Cooper&Hunter GWH09QC-D3DNA1D Victoria Owner's Manual

Cooper&Hunter GWH09QC-D3DNA1D Victoria Owner's Manual
VICTORIA
HIGH-WALL DUCTLESS
AIR CONDITIONING &
HEATING SYSTEM
OWNER'S MANUAL
Models:
GWH09QC-A3DNA1D (115V)
GWH12QC-A3DNA1D (115V)
GWH09QC-D3DNA1D (230V)
GWH12QC-D3DNA1D (230V)
GWH18QD-D3DNA1G (230V)
GWH24QE-D3DNA1D (230V)
GWH09QC-A3DNA1D(115V)
System Includes: GWH09QC-A3DNA1D/I, GWH09QC-A3DNA1D/O
GWH12QC-A3DNA1D(115V)
System Includes: GWH12QC-A3DNA1D/I, GWH12QC-A3DNA1D/O
GWH09QC-D3DNA1D(230V)
System Includes: GWH09QC-D3DNA1D/I, GWH09QC-D3DNA1D/O
GWH12QC-D3DNA1D(230V)
System Includes: GWH12QC-D3DNA1D/I, GWH12QC-D3DNA1D/O
GWH18QD-D3DNA1G(230V)
System Includes: GWH18QD-D3DNA1G/I, GWH18QD-D3DNA1G/O
GWH24QE-D3DNA1D(230V)
System Includes: GWH24QE-D3DNA1D/I, GWH24QE-D3DNA1D/O
Explanation of Symbols
Indicates a hazardous situation that, if not avoided, will
result in death or serious injury.
Indicates a hazardous situation that, if not avoided, could
result in death or serious injury.
Indicates a hazardous situation that, if not avoided, may
result in minor or moderate injury.
Indicates important but not hazard-related information,
used to indicate risk of property damage.
Indicates a hazard that would be assigned a signal word
WARNING or CAUTION.
Operation Notices
Content
Precautions. ...........................................................................................................1
Parts name . ...........................................................................................................6
Screen Operation Guide
Buttons on remote controller .................................................................................8
Introduction for icons on display screen ................................................................8
Introduction for buttons on remote controller .........................................................9
Function introduction for combination buttons .....................................................13
Operation guide ...................................................................................................15
Replacement of batteries in remote controller .....................................................15
Emergency operation . . .......................................................................................16
Maintenance
Clean and maintenance . .....................................................................................16
Malfunction
Malfunction analysis ............................................................................................19
System operation . ..............................................................................................23
Energy saving tips . .............................................................................................24
Precautions
WARNING
Operation and Maintenance
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety. Children should be supervised to
ensure that they do not play with the appliance.
Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by
children without supervision.
Do not connect air conditioner to multi-purpose socket.
Otherwise, it may cause fire hazard.
Do disconnect power supply when cleaning air
conditioner. Otherwise, it may cause electric shock.
If the supply cord is damaged, it must be replaced by
the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
Do not wash the air conditioner with water to avoid
electric shock.
Do not spray water on indoor unit. It may cause electric
shock or malfunction.
After removing the filter, do not touch fins to avoid injury.
Do not use fire or hair dryer to dry the filter to avoid
deformation or fire hazard.
1
Precautions
WARNING
Maintenance must be performed by qualified
professionals. Otherwise, it may cause personal injury
or damage.
Do not repair air conditioner by yourself. It may cause
electric shock or damage. Please contact dealer when
you need to repair air conditioner.
Do not extend fingers or objects into air inlet or air
outlet. It may cause personal injury or damage.
Do not block air outlet or air inlet. It may cause
malfunction.
Do not spill water on the remote controller, otherwise the
remote controller may be broken.
When below phenomenon occurs, please turn off air
conditioner and disconnect power immediately, and then
contact the dealer or qualified professionals for service.
● Power cord is overheating or damaged.
● There’s abnormal sound during operation.
● Circuit break trips off frequently.
● Air conditioner gives off burning smell.
● Indoor unit is leaking.
If the air conditioner operates under abnormal conditions,
it may cause malfunction, electric shock or fire hazard.
When turning on or turning off the unit by emergency
operation switch, please press this switch with an insulating
object other than metal.
Do not step on top panel of outdoor unit, or put heavy
objects. It may cause damage or personal injury.
2
Precautions
WARNING
Attachment
Installation must be performed by qualified professionals.
Otherwise, it may cause personal injury or damage.
Must follow the electric safety regulations when installing
the unit.
According to the local safety regulations, use qualified
power supply circuit and circuit break.
Do install the circuit break. If not, it may cause malfunction.
An all-pole disconnection switch having a contact separation
of at least 1/8in (3mm) in all poles should be connected
in fixed wiring.
Including an circuit break with suitable capacity, please
note the following table.Air switch should be included
magnet buckle and heating buckle function, it can protect
the circuit-short and overload.
Air Conditioner should be properly grounded. Incorrect
grounding may cause electric shock.
Don't use unqualified power cord.
Make sure the power supply matches with the
requirement of air conditioner.Unstable power supply or
incorrect wiring or malfunction. Please install proper power
supply cables before using the air conditioner.
Properly connect the live wire, neutral wire and
grounding wire of power socket.
Be sure to cut off the power supply before proceeding
any work related to electricity and safety.
3
Precautions
WARNING
Do not put through the power before finishing installation.
If the supply cord is damaged, it must be replaced by
the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
The temperature of refrigerant circuit will be high, please
keep the interconnection cable away from the copper
tube.
The appliance shall be installed in accordance with
national wiring regulations.
Installation must be performed in accordance with the
requirement of National Electrical Codes (NEC) and
local electrical codes by authorized personnel only.
The air conditioner is the first class electric appliance. It
must be properly grounding with specialized grounding
device by a professional. Please make sure it is always
grounded effectively, otherwise it may cause electric shock.
The yellow-green wire in air conditioner is grounding
wire, which can't be used for other purposes.
The grounding resistance should comply with national
electric safety regulations.
The appliance must be positioned so that the plug is
accessible.
All wires of indoor unit and outdoor unit should be
connected by a professional.
If the length of power connection wire is insufficient, please
contact the supplier for a new one. Avoid extending the
wire by yourself.
4
Precautions
WARNING
For the air conditioner with plug, the plug should be
reachable after finishing installation.
For the air conditioner without plug, an circuit break
must be installed in the line.
If you need to relocate the air conditioner to another
place, only the qualified person can perform the work.
Otherwise, it may cause personal injury or damage.
Select a location which is out of reach for children and
far away from animals or plants.If it is unavoidable,
please add the fence for safety purpose.
The indoor unit should be installed close to the wall.
Working temperature range
Maximum cooling
Maximum heating
Indoor side DB/WB(°C/°F) Outdoor side DB/WB(°C/°F)
26.7/19.4(80/66.9)
46.1/23.9(115/75)
26.7/-(80/-)
23.9/18.3(75/64.9)
NOTICE:
The operating temperature range (outdoor temperature) for cooling only unit is
-0.4°F(-18°C)~115°F(46.1°C); for heat pump unit is -4°F(-20°C)~115°F(46.1°C).
5
Parts Name
Indoor Unit
air inlet
panel
aux.button
horizontal louver
remote control
air outlet
(Display content or position may be different from above
graphics, please refer to actual products)
Outdoor Unit
air inlet
handle
air outlet
NOTICE:
Actual product may be different from above graphics, please refer to actual
products.
6
Parts Name
Display
For some model:
For some model:
cooling
indicator
power
indicator
receiver
window
heating
indicator
temp.
indicator
display
cooling
indicator
heating
indicator
temp.
indicator
drying
display
indicator
For some model:
receiver
window
power
indicator
drying
indicator
display
temp.
indicator
Power LED color indicator:
Green-status-ON.
Red -status-OFF.
receiver
window
Mode LED color indicator:
W
R
G
White-W-Cool ModeRed-R-Heat Mode-
W
(only for heating model)
R
Green-G-Dry Mode- G
For some model:
display
temp.
indicator
Power LED color indicator:
Green-status-ON.
Red -status-OFF.
receiver
window
Mode LED color indicator:
W
R
O
White-W-Cool ModeRed-R-Heat Mode-
R
W
(only for heating model)
Orange-O-Dry Mode- O
Display content or position may be different from above graphics, please refer to actual
products.
7
Buttons on remote controller
1
ON/OFF button
2 MODE button
3 FAN button
4 SWING button
2
4
3
5 TURBO button
5
6 ▲/
6
7
11
button
7 SLEEP button
8
9
▲
1
8 TEMP button
10
9 I FEEL button
12
10 LIGHT button
11 CLOCK button
12 TIMER ON/TIMER OFF
button
Introduction for icons on display screen
health function
I feel
Set fan speed
Send signal
Operation mode
Turbo mode
Auto mode
Cool mode
46°F(8°C) heating
function
Set temperature
Dry mode
Fan mode
Set time
TIMER ON/
TIMER OFF
Child lock
Heat mode
Clock
Sleep mode
Up&down swing
Light
Temp. display type
:Set temp.
:Indoor ambient temp.
:Outdoor ambient temp.
8
Introduction for buttons on remote controller
Note:
● This is a general use remote controller, it could be used for the air conditioners
with multifunction; For some function, which the model doesn't have, if press
the corresponding button on the remote controller that the unit will keep the
original running status.
● After putting through the power, the air conditioner will give out a sound.
Operation indictor " " is ON (red indicator). After that, you can operate the air
conditioner by using remote controller.
● Under ON status, pressing the button on the remote controller, the signal icon " "
on the display of remote controller will blink once and the air conditioner will give
out a “de” sound, which means the signal has been sent to the air conditioner.
● Under OFF status, set temperature and clock icon will be displayed on the display
of remote controller (If timer on, timer off and light functions are set, the corresponding icons will be displayed on the display of remote controller at the same
time); Under on status, the display will show the corresponding set function icons.
1
ON/OFF button
Press this button can turn on or turn off the air conditioner. After turning on the air
conditioner, operation indicator " "on indoor unit’s display is ON (green indicator.
The colour is different for different models), and indoor unit will give out a sound.
2
MODE button
Press this button to select your required operation mode.
AUTO COOL DRY
FAN
HEAT
● When selecting auto mode, air conditioner will operate automatically according
to ex-factory setting. Set temperature can’t be adjusted and will not be displayed
as well. Press "FAN" button can adjust fan speed. Press "SWING" button can
adjust fan blowing angle.
● After selecting cool mode, air conditioner will operate under cool mode. Cool
indicator " "on indoor unit is ON. Press "▲" or " " button to adjust set temperature. Press "FAN" button to adjust fan speed. Press "SWING" button to adjust
fan blowing angle.
● When selecting dry mode, the air conditioner operates at low speed under dry
mode. Dry indicator " " on indoor unit is ON. Under dry mode, fan speed can’t
be adjusted. Press "SWING" button to adjust fan blowing angle.
● When selecting fan mode, the air conditioner will only blow fan, no cooling and
no heating. All indicators are OFF. Press "FAN" button to adjust fan speed. Press
"SWING" button to adjust fan blowing angle.
● When selecting heating mode, the air conditioner operates under heat mode.
Heat indicator "
" on indoor unit is ON. Press "▲" or " " button to adjust set
▲
▲
9
Introduction for buttons on remote controller
temperature. Press "FAN" button to adjust fan speed. Press "SWING" button to
adjust fan blowing angle. (Cooling only unit won’t receive heating mode signal. If
setting heat mode with remote controller, press ON/OFF button can’t start up the
unit).
Note:
● For preventing cold air, after starting up heating mode, indoor unit will delay 1~5
minutes to blow air (actual delay time is depend on indoor ambient temperature).
● Set temperature range from remote controller: 60.8~86°F (16~30°C) ; Fan
speed: auto, low speed, medium speed, high speed.
3
FAN button
Pressing this button can set fan speed circularly as: auto (AUTO), low(
(
), high(
).
), medium
Auto
Note:
● Under AUTO speed, air conditioner will select proper fan speed automatically
according to ex-factory setting.
● Fan speed under dry mode is low speed.
4
SWING button
Press this button can select up&down swing angle. Fan blow angle can be selected
circularly as below:
no display
(horizontal louvers stops
at current position)
● When selecting " ", air conditioner is blowing fan automatically. Horizontal
louver will automatically swing up&down at maximum angle.
● When selecting " 、 、 、 、
● When selecting "
、 、
● Hold " "button above 2s to set your required swing angle. When reaching your
required angle, release the button.
Note:
" 、 、 " may not be available. When air conditioner receives this signal, the
air conditioner will blow fan automatically.
10
Introduction for buttons on remote controller
5 TURBO button
Under COOL or HEAT mode, press this button to turn to quick COOL or quick
HEAT mode. " " icon is displayed on remote controller. Press this button again
to exit turbo function and " " icon will disappear.
▲/
▲
6
button
▲
▲
● Press "▲" or " " button once increase or decrease set temperature 33.8°F(1°C).
Holding "▲" or " " button, 2s later, set temperature on remote controller will
change quickly. On releasing button after setting is finished, temperature indicator on indoor unit will change accordingly. (Temperature can’t be adjusted under
auto mode)
● When setting TIMER ON, TIMER OFF or CLOCK, press "▲" or " " button to
adjust time. (Refer to CLOCK, TIMER ON, TIMER OFF buttons) When setting
TIMER ON, TIMER OFF or CLOCK, press "▲" or " " button to adjust time. (Refer
to CLOCK, TIMER ON, TIMER OFF buttons)
▲
▲
7
SLEEP button
8
TEMP button
Under COOL, HEAT or DRY mode, press this button to start up sleep function.
" " icon is displayed on remote controller. Press this button again to cancel sleep
function and " " icon will disappear.
By pressing this button, you can see indoor set temperature, indoor ambient temperature or outdoor ambient temperature on indoor unit’s display. The setting on
remote controlleris selected circularly as below:
no display
● When selecting " " or no display with remote controller, temperature indicator
on indoor unit displays set temperature.
● When selecting " " with remote controller, temperature indicator on indoor unit
displays indoor ambient temperature.
● When selecting "
" with remote controller, temperature indicator on indoor unit
displays outdoor ambient temperature.
Note:
● Outdoor temperature display is not available for some models. At that time, indoor
unit receives "
" signal, while it displays indoor set temperature.
11
Introduction for buttons on remote controller
● It’s defaulted to display set temperature when turning on the unit. There is no
display in the remote controller.
● Only for the models whose indoor unit has dual-8 display.
● When selecting displaying of indoor or outdoor ambient temperature, indoor
temperature indicator displays corresponding temperature and automatically turn
to display set temperature after three or five seconds.
9
I FEEL button
Press this button to start I FEEL function and " " will be displayed on the remote
controller. After this function is set, the remote controller will send the detected
ambient temperature to the controller and the unit will automatically adjust the
indoor temperature according to the detected temperature. Press this button again
to close I FEEL function and " " will disappear.
● Please put the remote controller near user when this function is set. Do not put
the remote controller near the object of high temperature or low temperature in
order to avoid detecting inaccurate ambient temperature.
10
LIGHT button
Press this button to turn off display light on indoor unit. "
" icon on remote
controller disappears. Press this button again to turn on display light. "
" icon is
displayed.
11
CLOCK button
Press this button to set clock time. " " icon on remote controller will blink. Press
"▲" or " " button within 5s to set clock time. Each pressing of "▲" or " " button,
clock time will increase or decrease 1 minute. If hold "▲" or " " button, 2s later,
time will change quickly. Release this button when reaching your required time.
▲
▲
▲
Note:
● Clock time adopts 24-hour mode.
● The interval between two operation can’t exceeds 5s. Otherwise, remote controller will quit setting status. Operation for TIMER ON/TIMER OFF is the same.
12 TIMER ON / TIMER OFF button
● TIMER ON button
"TIMER ON" button can set the time for timer on. After pressing this button, " "
icon disappears and the word "ON" on remote controller blinks. Press "▲" or
" "button to adjust TIMER ON setting. After each pressing "▲" or " " button,
▲
▲
12
Introduction for buttons on remote controller
▲
TIMER ON setting will increase or decrease 1min. Hold "▲" or " " button, 2s
later, the time will change quickly until reaching your required time.
Press "TIMER ON" to confirm it. The word "ON" will stop blinking. " " icon
resumes displaying. Cancel TIMER ON: Under the condition that TIMER ON is
started up, press "TIMER ON" button to cancel it.
● TIMER OFF button
"TIMER OFF" button can set the time for timer off. After pressing this button, " "
icon disappears and the word "OFF" on remote controller blinks. Press "▲" or
" " button to adjust TIMER OFF setting. After each pressing "▲" or " " button,
TIMER OFF setting will increase or decrease 1min. Hold "▲" or " " button, 2s
later, the time will change quickly until reaching your required time.
Press "TIMER OFF" word "OFF" will stop blinking. " " icon resumes displaying.
Cancel TIMER OFF. Under the condition that TIMER OFF is started up, press
"TIMER OFF" button to cancel it.
▲
▲
▲
Note:
● Under on and off status, you can set TIMER OFF or TIMER ON simultaneously.
● Before setting TIMER ON or TIMER OFF, please adjust the clock time.
● After starting up TIMER ON or TIMER OFF, set the constant circulating valid.
After that, air conditioner will be turned on or turned off according to setting time.
ON/OFF button has no effect on setting. If you don’t need this function, please
use remote controller to cancel it.
Function introduction for combination buttons
Energy-saving function
Under cooling mode, press "TEMP" and " CLOCK" buttons simultaneously to
start up or turn off energy-saving function. When energy-saving function is started
up, "SE" will be shown on remote controller, and air conditioner will adjust the set
temperature automatically according to ex-factory setting to reach to the best
energy-saving effect. Press "TEMP" and "CLOCK" buttons simultaneously again to
exit energy-saving function.
Note:
● Under energy-saving function, fan speed is defaulted at auto speed and it can’t
be adjusted.
● Under energy-saving function, set temperature can’t be adjusted. Press "TURBO"
button and the remote controller won’t send signal.
● Sleep function and energy-saving function can’t operate at the same time. If
energy-saving function has been set under cooling mode, press sleep button will
cancel energy-saving function. If sleep function has been set under cooling
mode, start up the energy-saving function will cancel sleep function.
13
Function introduction for combination buttons
8℃ heating function
Under heating mode, press “TEMP” and “CLOCK” buttons simultaneously to start
up or turn off 46°F(8°C) heating function. When this function is started up, “ ” and
“46°F(8°C)” will be shown on remote controller, and the air conditioner keep the
heating status at 46°F(8°C). Press “TEMP” and “CLOCK” buttons simultaneously
again to exit 46°F(8°C) heating function.
Note:
● Under 46°F(8°C) heating function, fan speed is defaulted at auto speed and it
can’t be adjusted.
● Under 46°F(8°C) heating function, set temperature can’t be adjusted. Press
"TURBO" button and the remote controller won’t send signal.
● Sleep function and 46°F(8°C) heating function can’t operate at the same time. If
46°F(8°C) heating function has been set under cooling mode, press sleep button
will cancel 46°F(8°C) heating function. If sleep function has been set under cooling
mode, start up the 46°F(8°C) heating function will cancel sleep function.
● Under °F temperature display, the remote controller will display 46°F(8°C)
heating.
Child lock function
▲
Press "▲" and " " simultaneously to turn on or turn off child lock function. When
child lock function is on, " " icon is displayed on remote controller. If you operate
the remote controller, the " " icon will blink three times without sending signal to
the unit.
Temperature display switchover function
▲
Under OFF status, press " " and "MODE" buttons simultaneously to switch temperature display between ℃ and ℉ .
14
Operation guide
1. After putting through the power, press "ON/OFF" button on remote controller to
turn on the air conditioner.
2. Press "MODE" button to select your required mode: AUTO, COOL, DRY, FAN,
HEAT.
3. Press "▲" or " " button to set your required temperature. (Temperature can’t
be adjusted under auto mode).
4. Press "FAN" button to set your required fan speed: auto, low, medium and high
speed.
5. Press "SWING" button to select fan blowing angle.
▲
Replacement of batteries in remote controller
1. Press the back side of remote controller marked
with " ", as shown in the fig, and then push out
the cover of battery box along the arrow direction.
2. Replace two 7# (AAA 1.5V) dry batteries, and
make sure the position of "+" polar and "-" polar
are correct.
3. Reinstall the cover of battery box.
signal sender
battery
reinstall
remove
Cover of battery box
NOTICE
● During operation, point the remote control signal sender at the receiving
window on indoor unit.
● The distance between signal sender and receiving window should be no
more than 8m, and there should be no obstacles between them.
● Signal may be interfered easily in the room where there is fluorescent lamp
or wireless telephone; remote controller should be close to indoor unit during
operation.
● Replace new batteries of the same model when replacement is required.
● When you don’t use remote controller for a long time, please take out the
batteries.
● If the display on remote controller is fuzzy or there’s no display, please
replace batteries.
15
Emergency operation
If remote controller is lost or damaged, please use auxiliary button to turn
on or turn off the air conditioner. The operation in details are as below:
air conditioner. When the air conditioner is turned on, it will operate under
auto mode.
panel
aux. button
WARNING:
Use insulated object to press the auto button
Clean and maintenance
WARNING
■ Turn off the air conditioner and disconnect the power before cleaning the air
conditioner to avoid electric shock.
■ Do not wash the air conditioner with water to avoid electric shock.
■ Do not use volatile liquid to clean the air conditioner.
Clean surface of indoor unit
When the surface of indoor unit is dirty, it is recommended to use a soft dry cloth
or wet cloth to wipe it.
NOTICE:
● Do not remove the panel when cleaning it.
16
WARNING
CleanCAUTION
and maintenance
CAUTION
WARNING
• Turn off power and disconnect unit from power source before cleaning. Failure to
do so could cause electric shock.
•Never spray water on either indoor or outdoor unit. This could cause damage or
unit failure.
•Never use abrasive cleaners on indoor or outdoor unit. Use only slightly damp,
clean, soft cloth or very mild cleansers.
1
Open panel
3
Pull out the panel to a certain
● Use dust catcher or water to
the water (below 113°F(45°C) ) to
clean it, and then put it in a shady and
cool place to dry.
2
4
panel cover tightly.
WARNING
■ The filter should be cleaned every three months. If there is much dust in the
operation environment, clean frequency can be increased.
■ After removing the filter, do not touch fins to avoid injury.
■ Do not use fire or hair dryer to dry the filter to avoid deformation or fire hazard.
17
Clean and maintenance
NOTICE: Checking before use-season
1. Check whether air inlets and air outlets are blocked.
2. Check whether circuit break, plug and socket are in good condition.
4. Check whether drainage pipe is damaged.
NOTICE: Checking after use-season
1. Disconnect power supply.
Notice for recovery
1. Many packing materials are recyclable materials.
Please dispose them in appropriate recycling unit.
2. If you want to dispose the air conditioner, please contact local dealer or
consultant service center for the correct disposal method.
18
Malfunction analysis
General phenomenon analysis
Please check below items before asking for maintenance. If the malfunction still
can’t be eliminated, please contact local dealer or qualified professionals.
Phenomenon
Check items
Solution
● Whether it's interfered severely ● Pull out the plug. Reinsert
(such as static electricity,stable the plug after about 3min, and
voltage)?
then turn on the unit again.
Indoor unit
can’t receive
remote
controller’s
signal or
remote
controller
has no
action.
● Whether remote controller is
within the signal receiving
range?
● Signal receiving range is 8m.
● Whether there are obstacles?
● Remove obstacles.
● Whether remote controller is
● Select proper angle and point
pointing at the receiving
the remote controller at the rewindow?
ceiving window on indoor unit.
● Is sensitivity of remote contro- ● Check the batteries. If the
ller low; fuzzy display and no
power of batteries is too low,
display?
please replace them.
● Check whether remote cont● No display when operating
roller appears to be damaged.
remote controller?
If yes, replace it.
● Fluorescent lamp in room?
No air
emitted
from
indoor
unit
● Take the remote controller
close to indoor unit.
● Turn off the fluoresent lamp
and then try it again.
● Air inlet or air outlet of indoor
unit is blocked?
● Eliminate obstacles.
● Under heating mode, indoor
temperature is reached to set
temperature?
● After reaching to set temperature, indoor unit will stop blowing out air.
● Heating mode is turned on just ● In order to prevent blowing
now?
out cold air, indoor unit will be
started after delaying for several minutes, which is a normal phenomenon.
19
Malfunction analysis
Phenomenon
Air conditioner can’t
operate
Mist is emitted from
indoor unit’s
air outlet
Set temperature can’t
be adjusted
Cooling
(heating)
effect is
not good.
Check items
Solution
● Power failure?
● Wait until power recovery.
● Is plug loose?
● Reinsert the plug.
● Circuit break trips off or
fuse is burnt out?
● Ask professional to replace
circuit break or fuse.
● Wiring has malfunction?
● Ask professional to replace it.
● Unit has restarted immediately
● Wait for 3min, and then turn
after stopping operation?
on the unit again.
● Whether the function setting
for remote controller is
correct?
● Reset the function.
● Indoor temperature and humidity is high?
● Because indoor air is cooled
rapidly. After a while, indoor
temperature and humidity will
be decrease and mist will
disappear.
● Unit is operating under auto
mode?
● Temperature can’t be adjusted under auto mode.
Please switch the operation
mode if you need to adjust
temperature.
● Your required temperature
exceeds the set temperature
range?
● Set temperature range:
60.8~86°F (16~30°C).
● Voltage is too low?
● Wait until the voltage
resumes normal.
● Filter is dirty?
● Clean the filter.
● Set temperature is in proper
range?
● Adjust temperature to proper
range.
● Door and window are open?
● Close door and window.
20
Malfunction analysis
Phenomenon
Odours are
emitted
Check items
Solution
● Whether there’s odour source, ● Eliminate the odour source.
such as furniture and cigarette,
● Clean the filter.
etc.
Air conditioner ● Whether there’s interference,
such as thunder, wireless
operates normally suddenly devices, etc.
“Water
flowing”
noise
Cracking
noise
● Air conditioner is turned on or
turned off just now?
● Air conditioner is turned on or
turned off just now?
WARNING
● Disconnect power, put back
power, and then turn on the
unit again.
● The noise is the sound of
refrigerant flowing inside
the unit, which is a normal
phenomenon.
● This is the sound of friction
caused by expansion and/or
contraction of panel or other
parts due to the change of
temperature.
CAUTION
WARNING
WARNING
Do not attempt any repairs on the unit yourself. Incorrect repair can cause
shock or fire. Always call a qualified service professional. Using these
troubleshooting suggestions can save time when you contact the qualified
service professional.
21
Malfunction analysis
Error Code
● When air conditioner status is abnormal, temperature indictor on indoor unit will
ation of error code.
Error code
E5
E8
U8
H6
Troubleshooting
It can be eliminated after restarting the unit. If not,please
It can be eliminated after restarting the unit. If not,please
It can be eliminated after restarting the unit. If not,please
It can be eliminated after restarting the unit. If not, please
C5
F1
F2
Note:
service.
WARNING
■ When below phenomenon occurs, please turn off air conditioner and disconfor service.
● Power cord is overheating or damaged.
● There’s abnormal sound during operation.
● Air switch trips off frequently.
● Air conditioner gives off burning smell.
● Indoor unit is leaking.
■ If the air conditioner operates under abnormal conditions, it may cause
22
SYSTEM OPERATION
COOLING OPERATION
How it works:
In cooling mode, your victoria indoor unit will absorb heat from
the room, then the victoria outdoor unit will discharge the heat to
the outdoors. The victoria cooling capacity decreases as the outdoor
temperature increases. This causes the victoria to work harder and
longer to hold the selected room temperature.
Indoor Coil Freeze Protection:
Frost may form on the indoor coil during cooling operations when the
outdoor temperature below 50°F (10°C). Prolong operation may cause ice
to form on the indoor coil and block airflow. If the victoria indoor
unit microcomputer detects ice on the indoor coil it will stop the
compressor to defrost the coil and protect the unit.
HEATING OPERATION
How it works:
In heating mode, your victoria outdoor unit will absorb heat from
the outdoor ambient, then the victoria indoor unit will discharge the
heat to the room. The victoria heating capacity decreases as the outdoor
temperature decreases.
During extreme cold outdoor temperatures, you may need an additional
heating source to supplement the victoria heating output.
Defrost Function:
In heating mode, frost may form on the outdoor coil during humid and low
outdoor temperature conditions. Prolong operation may cause ice to form
on the outdoor coil and block airflow. This will reduce the victoria’s
heating capacity.
If the victoria microcomputer detects ice on the outdoor coil, it will
switch automatically to defrost mode to melt the ice and clear the coil.
During defrost mode, heating will be discontinued and the victoria
indoor unit will flash the Defrost indicator. The compressor will
continue to run while indoor and outdoor fans will stop. It is normal to see
steam or vapor coming from the outdoor unit during defrost mode. Defrost
mode will terminate 12 minutes after initiation of defrost cycle or when the
outdoor coil temperature is 50°F (10°C) or greater.
23
ENERGY SAVING TIPS
1. Relaxing room temperature at night is OK: During the nighttime
hours you don’t require the same level of conscious cooling or heating.
Try using Sleep Mode to gradually relax room temperature and allow the
unit to run less and save energy.
2. Curtains and shades: In the summer, you need to block the effects of
the sun. Close window curtains and shades on the south and west side
of your home to help block solar heat. In winter, the sun is your friend.
Open curtains and shades to allow solar heat into your room.
3. Close doors: If you don’t need to heat and cool your whole home,
confine the heating and cooling to one room by closing doors. Limit the
space you’re heating and cooling to specified capability of the unit.
4. Service the unit: Some basic maintenance might be all you need. The
outdoor unit will greatly benefit from a good hosing out, especially in
treed areas where seeds and other debris can stick to coil fins and make
the unit work up to 15% harder!
5. Rearrange the room: Furniture that obstructs airflow means you could
be heating and cooling the back of a chair or the front of a sofa instead
of the actual living space. Use the Swing Louvers to help direct the air in
the right direction for the room; remove or rearrange obstacles blocking
airflow.
6. Try 75 degrees: 75°F is a good point for an air conditioner to run at its
optimal performance level. Even a 5-degree change in temperature can
make your unit use up to 40% more energy!
7. Lighting: Turning lights off can help reduce your heat. Each light bulb is
a tiny heater. Your air conditioner must waste energy overcoming the
heat from your lights to reach and hold your desired room temperature.
8. Is anyone home? If possible, while you’re away turn your unit to Auto
mode and make sure windows and drapes are closed. Although the
room temperature will be uncomfortable for a few minutes when you
come home, the unit will have the room back to your desired
temperature in no time.
9. Don’t forget the fan: The fan is much like a car. The faster it runs, the
more energy is uses. Sometimes we need the car to go fast, but slow is
good enough most of the time. Try saving money by using the
comfortable quiet low fan speed as much as possible.
24
www.cooperandhunter.us
LIMITED WARRANTY STATEMENT
Ductless Heat Pump Split System
FOR WARRANTY SERVICE OR REPAIR:
Contact your installing contractor. You may find the installer’s name on the equipment or in your Owner’s packet.
Complete product registration below and send back by e-mail at
PRODUCT REGISTRATION:
Model No.: ______________________________________________________________________________________________
Serial No.: _______________________________________________________ Date of Installation: ______________________
Owner Name: ____________________________________________________________________________________________
Address of Installation:_____________________________________________________________________________________
Installing Contractor: ______________________________________________________________________________________
Address: ________________________________________________________________________________________
Phone No. / E-mail: _______________________________________________________________________________
C&H distributor (hereinafter “Company”) warrants this product against failure due to defect in materials or workmanship
under normal use and maintenance as follows. All warranty periods begin on the date of original installation. If the date cannot
be verified, the warranty period begins one hundred twenty (120) days from date of manufacture. If a part fails due to defect
during the applicable warranty period Company will provide a new or remanufactured part, at Company’s option, to replace the
failed defective part at no charge for the part. This limited warranty is subject to all provisions, conditions, limitations and
exclusions listed below.






A warranty period of Seven (7) years on compressor to the original registered end-user.
A warranty period of Five (5) years on all parts to the original registered end user.
A warranty period of One (1) year on the remote control provided with the original unit.
Limited warranty applies only to systems that are properly installed by a state certified or licensed HVAC contractor,
under applicable local and state law in accordance with all applicable building codes and permits; C&H installation
and operation instructions and good trade practices.
Warranty applies only to products remaining in their original installation location.
Defective parts must be returned to the distributor through a registered servicing dealer for credit.
LIMITATIONS OF WARRANTIES:
ALL IMPLIED WARRANTIES AND/OR CONDITIONS (INCLUDING IMPLIED WARRANTIES OR
CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR USE OR PURPOSE) ARE LIMITED TO THE DURATION OF
THIS LIMITED WARRANTY, SOME STATES OR PROVINCES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY
OR CONDITION LASTS, SO THE ABOVE MAY NOT APPLY TO YOU. THE EXPRESS WARRANTIES MADE IN THIS WARRANTY ARE
EXCLUSIVE AND MAY NOT BE ALTERED, ENLARGED, OR CHANGED BY ANY DISTRIBUTOR, DEALER, OR OTHER PERSON,
WHATSOEVER.
THIS WARRANTY DOES NOT COVER:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
Labor or other costs incurred for diagnosing, repairing, removing, installing, shipping, servicing or handling of either
defective parts, or replacement parts, or new units.
Product cleaning required prior to warranty service and repair.
Normal maintenance as outlined in the installation and servicing instructions or Owner’s Manual, including filter
cleaning and/or replacement and lubrication.
Failure, damage or repairs due to faulty installation, misapplication, abuse, improper servicing, unauthorized
alteration or improper operation.
Failure to start due to voltage conditions, blown fuses, open circuit breakers, or damages due to the inadequacy or
interruption of electrical service.
Failure or damage due to floods, winds, fires, lightning, accidents, corrosive environments (rust, etc.) or other
conditions beyond the control of the Company.
Failure or damage of coils or piping due to corrosion on installations within one (1) miles of sea coast or corrosive
body.
Parts not supplied or designated by Company, or damages resulting from their use.
Products installed outside continental USA and Canada.
Electricity or fuel costs, or increases in electricity or fuel costs from any reason whatsoever, including additional or
unusual use of supplemental electric heat.
Any cost to replace, refill or dispose of refrigerant, including the cost of refrigerant.
Shipping damage or damage as a result of transporting the unit.
Accessories such as condensate pumps, line sets and so forth are not covered.
Any special, indirect or consequential property or commercial damage of any nature whatsoever. Some states or
provinces do not allow the exclusion of incidental or consequential damages, so the above limitation may not apply to
you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to
province.
66160000086
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement