Klimaire | KSIL024H219 | User manual | Klimaire KSIL024H219 User Manual

19 SEER 9 ~18K
R ead This Manual
Inside you will find many helpful hints on how
to use and maintain your air conditioner properly.
Just a little preventative care on your part can
save you a great deal of time and money over
the life of your air conditioner. You'll find many
answers to common problems in the chart of
troubleshooting tips. If you review the chart of
Troubleshooting Tips first, you may not need
to call for service.
Sociable remark................................................................................................................2
Warning ...........................................................................................................................3
Caution ............................................................................................................................4
Parts names ........... ...................................................................................................5
Special functions ............................................................................................................6
Operating temperature.....................................................................................................7
Manual operation ............................................................................................................7
Airflow direction control
How the air conditioner works ........................................................................................9
Care and maintenance
Operation tips ............
Troubleshooting tips
Contact an authorised service technician for repair or maintenance of this unit.
Contact the authinstaller for installation of this unit.
This appliance is not intended for use by persons(including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
Young children should be supervised to ensure that they do not play with the
air conditioner.
If the power cord is to be replaced, replacement work shall be performed by
authorised personnel only.
Installation work must be performed in accordance with the national wiring
standards by authorised personnel only.
When using this air conditioner in the European countries, the following
informations must be followed:
DISPOSAL: Do not dispose this product as unsorted municipal waste. Collection
of such waste separately for special treatment is necessary.
It is prohibited to dispose of this appliance in domestic household waste.
For disposal, there are several possibilities:
A) The municipality has established collection systems, where electronic waste can
be disposed of at least free of charge to the user.
B) When buying a new product, the retailer will take back the old product at least
free of charge.
C) The manufacture will take back the old appliance for disposal at least free of
charge to the user.
D) As old products contain valuable resources, they can be sold to scrap metal
Wild disposal of waste in forests and landscapes endangers your health when
hazardous substances leak into the ground-water and find their way into the food
To prevent injury to the user or other people and property damage, the following instructions
must be followed. Incorrect operation due to ignoring of instructions may cause harm or damage.
The seriousness is classified by the following indications.
This symbol indicates the possibility of death or serious injury.
This symbol indicates the possibility of injury or damage to property.
Meanings of symbols used in this manual are as shown below.
Never do this.
Always do this.
Connect with the power
Do not operate or stop the
unit by switching on or off
the power.
Do not damage or use an
unspecified power cord.
Otherwise, it may cause electric
shock or fire due to excess heat
It may cause electric shock or fire
due to heat generation.
It may cause electric shock
or fire.
Do not modify power cord
length or share the outlet
with other appliances
It may cause electric shock
or fire due to heat generation.
Do not operate with wet
hands or in damp
Do not direct airflow at
room occupants only.
It may cause electric shock.
This could damage your
Always ensure effective
Do not allow water to run
into electric parts.
No earthing may cause
electric shock.
It may cause failure of
machine or electric shock.
Always install circuit
breaker and a dedicated
power circuit.
No installation may cause
fire and electric shock.
Disconnect the power if
strange sounds, smell, or
smoke comes from it.
It may cause fire and
electric shock.
Do not drink water drained
from air conditioner.
Do not open the unit
during operation.
It contains contaminants and
could make you sick.
It may cause electric shock.
Use the correctly rated
breaker or fuse.
Do not use the power cord
close to heating appliances.
Do not disassemble or
modify unit.
There is risk of fire or
electric shock.
It may cause fire and
electric shock.
It may cause failure and
electric shock.
Do not use the power cord near
flammable gas or combustibles, such
as gasoline, benzene, thinner, etc.
Ventilate room before operating air
conditioner if there is a gas leakage
from another appliance.
It may cause explosion, fire and, burns.
It may cause an explosion or fire.
When the air filter is to be
removed, do not touch the
metal parts of the unit.
Do not clean the air
conditioner with water.
It may cause an injury.
Water may enter the unit and
degrade the insulation. It may
cause an electric shock.
An oxygen shortage
may occur.
When the unit is to be
cleaned, switch off, and turn
off the circuit breaker.
Do not put a pet or house
plant where it will be
exposed to direct air flow.
Do not use for
special purposes.
Do not clean unit when
power is on as it may cause
fire and electric shock, it may
cause an injury.
This could injure the pet or
Stop operation and close
the window in storm or
Do not place obstacles
around air-inlets or inside
of air-outlet.
Do not use this air conditioner to preserve precision devices, food, pets,
plants, and art objects.
It may cause deterioration
of quality, etc.
Turn off the main power
switch when not using
the unit for a long time.
Operation with windows
opened may cause wetting
of indoor and soaking of
household furniture.
It may cause failure of
appliance or accident.
Do not use strong detergent
such as wax or thinner. Use
a soft cloth for cleaning.
Appearance may be
deteriorated due to change
of product color or
scratching of its surface.
Do not place heavy object on the
power cord and take care so that
the cord is not compressed.
Ensure that the installation bracket of
the outdoor appliance is not damaged
due to prolonged exposure.
If bracket is damaged, there
is concern of damage due to
falling of unit.
Use caution when unpacking
and installing. Sharp edges
could cause injury.
There is danger of fire or
electric shock.
Ventilate the room well
when used together
with a stove, etc.
It may cause failure of
product or fire.
Always insert the filters
securely. Clean filter
once every two weeks.
Operation without filters
may cause failure.
! If water enters the
unit, turn the unit off
and disconnect the
power , contact a
qualified service
Parts names
Indoor unit
NOTE: The indoor unit you purchased would like one of the following. There is a slightly
difference on front panel and display window, but the features are the same.
Indoor unit
Front panel
Air inlet
Air filter(under the panel)
Air outlet
Horizontal air flow grille
Vertical air flow louver(inside)
Display panel
Connecting pipe, drain hose
Outdoor unit
9. Connective cable
10. Connecting pipe
11. Stop valve
Outdoor unit
Air inlet(side)
Air inlet(rear)
All the pictures in this manual are for
explanation purpose only. Your air
conditioner may be slightly different.
The actual shape shall prevail.
Air outlet
Indicator Lights on Display panel
NOTE:The display panel of the indoor
unit you purchased may be look like
one of the following:
Auto indicator:
This indicator illuminates when the air
conditioner is in AUTO operation.
Timer indicator:
This indicator illuminates when TIMER
is set ON/OFF.
Defrost Indicator
(For cooling& heating model only):
This indicator illuminates when the air
conditioner starts defrosting automatically
or when the warm air control feature is
activated in heating operation.
Ion Indicator
Lights up when Ion feature is activated and
Ionizer can generate abundant anions to fill
the room with refreshing and natural air.
NOTE: This function is only available for
air conditioner adopts Ionizer.
and malfunction/protection code whenthe
Frequency display:
This display is separated into five zones.
The zones illuminate based on the
compressor current frequency. For example,
higher frequency will illuminate more zones.
RUN indication lamp
run This lamp illuminates when the air
conditioner is in operation.
AUTO indication lamp
Ion indication lamp(optional function)
Lights up when Clean Air feature is
activated and Ionizer can generate
abundant anions to fill the room with
refreshing and natural air .
TIMER indication lamp
timer Lights up during Timer operation.
(C )
DEFROST indication lamp
(For cooling & heating models only):
def. Lights up when the air conditioner starts
defrosting automatically or when the warm
air control feature is activated in heating
NOTE: This manual does not include Remote Controller Operations, see the
<<Remote Controller Instruction>> packed with the unit for details.
Operating temperature
Room temperature
Outdoor temperature
1. If air conditioner is used outside of the above conditions, certain safety protection
features may come into operation and cause the unit to function abnormally.
2. Room relative humidity less than 80%. If the air conditioner operates in excess of this
figure, the surface of the air conditioner may attract condensation. Please sets the vertical
air flow louver to its maximum angle (vertically to the floor), and set HIGH fan mode.
3. Optimum performance will be achieved within these operating temperature.
Suggestion: For the unit adopts an Electric Heater, when the outside ambient temperature
is below 0C(32 F), we strongly recommend you to keep the machine plugged in order to
guarantee it running smoothly.
Manual operation
Manul operation can be used temporarily in case the remote controller is disable or
maintenance necessary.
NOTE: The unit must be turned off before
operating the manual control button. If the
unit is operational, continue pressing the
manual control button until the unit is off.
1 Open and lift the front panel up to an angle
until it remains fixed with a clicking sound.
2 One press of the manual control button will
lead to the forced AUTO operation. If press
the button twice within five seconds, the unit
will operate under forced COOL operation.
3 Close the panel firmly to its original
Manual control
This button is used for testing purposes
only. You had better not choose it.
To restore the remote controller operation,
use the remote controller directly.
Airflow direction control
Adjust the air flow direction properly otherwise, it
might cause discomfort or cause uneven room
Adjust the horizontal louver using the remote
Adjust the vertical louver manually.
To set the vertical air flow(Up--Down) direction
Perform this function while the unit is in operation.
Use the remote controller to adjust the air flow
direction. The horizontal louver can be moved at
a range of 6O for each press, or swing
,, up and down
automatically. Please refer to the REMOTE
(three places)
To set the horizontal air flow direction (left - right)
Move the vertical louver manually to adjust the air
flow in the direction you prefer .
IMPORTANT: Before adjusting the vertical louvers,
the supply power must be disconnected.
For some models, the vertical louver can be adjusted
using the remote controller.
Please refer to the ,,
for details.
Do not operate the air conditioner for long periods with
the air flow direction set downward in cooling or
dehumidifying mode. Otherwise, condensation may
occur on the surface of the horizontal louver causing
moisture to drop on to the floor or on furnishings.
Do not move the horizontal louver manually unless it is
necessary. Always use the remote controller.
When the air conditioner is started immediately after it
was stopped, the horizontal louver might not move for
approximately 10 seconds.
Open angle of the horizontal louver should not be set
too small, as COOLING or HEATING performance may
be impaired due to too restricted air flow area.
Do not operate unit with horizontal louver in closed
When the air conditioner is connected to power (initial
power), the horizontal louver may generate a sound for
10 seconds, this is a normal operation.
How the air conditioner works
SLEEP operation
7 hours timer off
1 hour
1 hour
SLEEP operation
7 hours timer off
1 hour 1 hour
AUTO operation
When you set the air conditioner in AUTO mode, it will
automatically select cooling, heating(cooling/heating
models only), or fan only operation depending on what
temperature you have selected and the room
The air conditioner will control room temperature
automatically round the temperature point set by you.
If the AUTO mode is uncomfortable, you can select
desired conditions manually.
SLEEP operation
When you push SLEEP button on remote controller
during cooling, heating(cooling & heating models only),
or AUTO operation , the air conditioner will
automatically increase (cooling) or decrease (heating)
per hour for the first 2 hours, then hold
steady for the next 5 hours, after that it will switch off.
This characteristic maintains both enery saving and
comfort in night operation.
DRYING operation
The fan speed will be automatically controlled under
dry operation.
During the dry operation, if the room temperature is
lower than 10OC(50F),
the compressor stops operation
and restarts until the room temperature is above
Optimal operation
To achieve optimal performance, please note the
Adjust the air flow direction correctly so that it is not
directed on people.
Adjust the temperature to achieve the highest comfort
level. Do not adjust the unit to excessive temperature
Close doors and windows on COOL or HEAT modes,
or performance may be reduced.
Use TIMER ON button on the remote controller to
select a time you want to start your air conditioner.
Do not put any object near air inlet or air outlet, as the
efficiency of the air conditioner may be reduced and
the air conditioner may stop running.
Clean the air filter periodically, otherwise cooling or
heating performance may be reduced.
Do not operate unit with horizontal louvre in closed
Care and maintenance
Cleaning the Grille, Case and Remote Controller
Turn the system off before cleaning. To clean, wipe
with a soft, dry cloth. Do not use bleach or abrasives.
NOTE: Supply power must be disconnectd before
cleaning the indoor unit.
Filter Handle
A cloth dampened with cold water may be used
on the indoor unit if it is very dirty. Then wipe it
with a dry cloth.
Do not use a chemically treated cloth or duster to
clean the unit.
Do not use benzine, thinner, polishing powder, or
similar solvents for cleaning. These may cause
the plastic surface to crack or deform.
Never use water hotter than 40OC/104OF to clean
the front panel, it could cause deformation of
Cleaning the air filter
A clogged air filter reduces the cooling efficiency of
this unit. Please clean the filter once every 2 weeks.
1. Lift the indoor unit panel up to an angle until it
stops with a clicking sound.
2. Take hold of the handle of the air filter and lift it
up slightly to take it out from the filter holder,
then pull it downwards.
3. Remove the AIR FILTER from the indoor unit.
Clean the AIR FILTER once two weeks.
Clean the AIR FILTER with a vacuum cleaner
or water, then dry it up in cool place.
Air freshening filter
Air freshening filter
4. Remove the Air Freshening Filter from its support
frame (on some models).
(The optional filter include :Plasma Dust Collector/
Silver Ion filter /Bio filter /Vitamin C filter/3M air
purifier filter, etc. The removing and installation
methods are slightly different, see the pictures
marked 1 and 2 on the left.
Clean the air freshening filter at least once a
month, and replace it every 4-5 months.
Clean it with vacuum cleaner, then dry it in cool
Do not touch the Plasma Dust Collector
Filter within 10 minutes after opening the
front panel, it may cause an electric shock.
5. Install the air freshening filter back into position.
6. Insert the upper portion of air filter back into the
unit, taking care that the left and right edges line
up correctly and place filter into position.
If you plan to idle the unit for a long time, perform
the following:
(1) Operate the fan for about half a day to dry the
inside of the unit.
(2) Stop the air conditioner and disconnect power.
Remove the batteries from the remote controller.
(3) The outdoor unit requires periodic maintenance
and cleaning. Do not attempt to do this yourself.
Contact your dealer or servicer.
Checks before operation
Check that the wiring is not broken off or
Check that the air filter is installed.
Check if the air outlet or inlet is blocked after the
air conditioner has not been used for a long time.
Do not touch the metal parts of the unit when
removing the filter . Injuries can occur when
handling sharp metal edges.
Do not use water to clean inside the air conditioner.
Exposure to water can destroy the insulation,
leading to possible electric shock.
When cleaning the unit, first make sure that the
power and circuit breaker are turned off.
The following events may occur during normal operation.
1. Protection of the air conditioner.
Compressor protection
The compressor can't restart for 3 minutes after it stops.
Anti-cold air (Cooling and heating models only)
The unit is designed not to blow cold air on HEAT mode, when the indoor heat
exchanger is in one of the following three situations and the set temperature has not
been reached.
A) When heating has just starting.
B) Defrosting.
C) Low temperature heating.
The indoor or outdoor fan stop running when defrosting (Cooling and heating models
Defrosting (Cooling and heating models only)
Frost may be generated on the outdoor unit during heat cycle when outdoor temperature
is low and humidity is high resulting in lower heating efficiency of the air conditioner.
During this condition air conditioner will stop heating operation and start defrosting
The time to defrost may vary from 4 to 10 minutes according to the outdoor temperature
and the amount of frost build up on the outdoor unit.
2. A white mist coming out from the indoor unit
A white mist may generate due to a large temperature difference between air inlet and
air outlet on COOL mode in an indoor environment that has a high relative humidity.
A white mist may generate due to moisture generated from defrosting process when
the air conditioner restarts in HEAT mode operation after defrosting.
3. Low noise of the air conditioner
You may hear a low hissing sound when the compressor is running or has just stopped
running. This sound is the sound of the refrigerant flowing or coming to a stop.
You can also hear a low "squeak" sound when the compressor is running or has just
stopped running. This is caused by heat expansion and cold contraction of the plastic
parts in the unit when the temperature is changing.
A noise may be heard due to louver restoring to its original position when power is first
turned on.
4. Dust is blown out from the indoor unit.
This is a normal condition when the air conditioner has not been used for a long time or
during first use of the unit.
5. A peculiar smell comes out from the indoor unit.
This is caused by the indoor unit giving off smells permeated from building material, from
furniture, or smoke.
6. The air conditioner turns to FAN only mode from COOL or HEAT (For cooling and
heating models only) mode.
When indoor temperature reaches the temperature setting on air conditioner, the
compressor will stop automatically, and the air conditioner turns to FAN only mode. The
compressor will start again when the indoor temperature rises on COOL mode or falls on
HEAT mode (For cooling and heating models only) to the set point.
7. Dripping water may generate on the surface of the indoor unit when cooling in a high
relatively humidity (relative humidity higher than 80%). Adjust the horizontal louver to
the maximum air outlet position and select HIGH fan speed.
8. Heating mode (For cooling and heating models only)
The air conditioner draws in heat from the outdoor unit and releases it via the indoor unit
during heating operation. When the outdoor temperature falls, heat drawn in by the air
conditioner decreases accordingly. At the same time, heat loading of the air conditioner
increases due to larger difference between indoor and outdoor temperature. If a
comfortable temperature can't be achieved by the air conditioner, we suggest you use a
supplementary heating device.
9. Auto-restart function
Power failure during operation will stop the unit completely.
For the unit without Auto-restart feature, when the power restores, the OPERATION indicator
on the indoor unit starts flashing. To restart the operation, push the ON/OFF button on the
remote controller. For the unit with Auto-restart feature, when the power restores, the unit
restarts automatically with all the previous settings preserved by the memory function.
For some models, the machine is special designed with Auto-restart function for the open
angle of the horizontal louver.Power failure during operation or pressing the ON/OFF button
on the remote controller will stop the unit completely.When the power restores or pressing
the ON/OFF button on the remote controller again,the unit restarts automatically with all the
previous settings including the open angle of the horizontal louver by the memory function.
So we strongly suggest that the open angle of the horizontal louver should not be set too
small,in case the condensed water forms and drops from the horizontal louver. Press the
AUTO/COOL button under the front panel and the open angle of the horizontal louver will be
restored to the standard angle when the condensed water forms on the horizontal louver.
10. Lightning or a car wireless telephone operating nearby may cause the unit to malfunction.
Disconnect the unit with power and then re-connect the unit with power again. Push the
ON/OFF button on the remote controller to restart operation.
Troubleshooting Tips
Stop the air conditioner immediately if one of the following faults occur. Disconnect the
power and contact the nearest customer service center.
If the following code appears on the LED window, disconnect the power and contact
the service people: E0,E1,E2,E3,E4,E5,E6,E7,E8 or P0,P1,P2,P3,P4, P6.
Fuse blows frequently or circuit breaker trips frequently.
Other objects or water penetrate the air conditioner.
The remote controller won't work or works abnormally.
Operaton indicator or other indicators flash rapidly and this flash can not be
stopped by disconnecting the power and then connecting it in again.
Unit does not
What should be done?
Power cut
Wait for power to be restored.
Unit may have become unplugged.
Check that plug is securely in wall
Fuse may have blown.
Replace the fuse.
Battery in Remote controller may
have been exhausted.
Replace the battery.
The time you have set with timer
is incorrect.
Wait or cancel timer setting.
Unit not cooling Inappropriate temperature
or heating
Set temperature correctly. For
(Cooling/ heating
"Using remote control" section.
models only)
room very well
detailed method please refer to
Air filter is blocked.
Clean the air filter.
while air flowing Doors or Windows are open.
Close the doors or windows.
out from the air
Air inlet or outlet of indoor or
outdoor unit has been blocked.
Clear obstructions away first, then
restart the unit.
Compressor 3 minutes
protection has been activated.
If the trouble has not been corrected, please contact a local dealer or the nearest customer
service center. Be sure to inform them of the detailed malfunctions and unit model.
Notes: Do not attempt to repair the unit yourself.
Always consult an authorised service provider.
7909 N.W. 54th Street, Miami, FL 33166 USA
Tel: (305)594-4972 Fax (305) 675-2212
The design and specifications are subject to change without prior notice for
product improvement. Consult with the sales agency or manufacturer for details.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF