USER’S MANUAL PACKAGED TERMINAL AIR CONDITIONER WITH HEAT PUMP / HEAT STRIP Model: CH-PT09HPGF CH-PT09HSGF The warranty is only valid when installed by a LICENSED HVAC TECHNICIAN. F or proper operation, please read and keep this manual carefully. Designed by Cooper&Hunter International Corporation, Oregon, USA www.cooperandhunter.com CONTENTS 1. SAFETY PRECAUTIONS..................................................................2 2. IMPORTANT SAFETY INSTRUCTIONS ..........................................4 3. AIR CONDITIONER FEATURES.......................................................5 4. CONTROL PANEL OPERATION.......................................................6 5. INSTALLATION .................................................................................7 6. CARE AND CLEANING......................................................................9 7. TROUBLESHOOTING.......................................................................10 Read This Manual Inside you will find many helpful hints on how to use and maintain your air conditioner properly. Just a little preventive care on your part can save you a great deal of time and money over the life of your air conditioner. You'll find many answers to common problems in the chart of troubleshooting tips. If you review our chart of Troubleshooting Tips first, you may not need to call for service at all. ! CAUTION This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play the appliance. Cleaning and user maintenance shall not be made by children without supervision. ( be applicable for the European Countries ) This appliance is not intended for use by persons (including children) with reduced physical ,sensory or mental capabilities or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. (be applicable for other countries except the European Countries ) Children should be supervised to ensure that they do not play with the appliance. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. The appliance shall be installed in accordance with national wiring regulations. Do not operate your air conditioner in a wet room such as a bathroom or laundry room. The appliance with electric heater shall have at least 1 meter space to the combustible materials. Contact the authorised service technician for repair or maintenance of this unit. Contact the authorised installer for installation of this unit. 1 SAFETY PRECAUTIONS To prevent injury to the user or other people and property damage, the following instructions must be followed. Incorrect operation due to ignoring of instructions may cause harm or damage. The seriousness is classified by the following indications. ! WARNING This symbol indicates the possibility of death or serious injury. ! CAUTION This symbol indicates the possibility of injury or damage to property. Meanings of symbols used in this manual are as shown below. Never do this. ! Always do this. ! WARNING ! ! ! ! ! ! Plug in power plug properly. Do not operate or stop the unit by inserting or pulling out the power plug. Do not damage or use an unspecified power cord. Otherwise, it may cause electric shock or fire due to excess heat generation. It may cause electric shock or fire due to heat generation. It may cause electric shock or fire. If the power cord is damaged, it must be replaced by the manufacturer or an authorised service centre or a similarly qualified person in order to avoid a hazard. Do not modify power cord length or share the outlet with other appliances. Do not operate with wet hands or in damp environment. It may cause electric shock or fire due to heat generation. It may cause electric shock. This could damage your health. Always ensure effective earthing. Do not allow water to run into electric parts. ! Incorrect earthing may cause electric shock. It may cause failure of machine or electric shock. Incorrect installation may cause fire and electric shock. Unplug the unit if strange sounds, smell, or smoke comes from it. Do not use the socket if it is loose or damaged. It may cause fire and electric shock. It may cause fire and electric shock. Keep firearms away. Do not use the power cord close to heating appliances. It may cause fire. It may cause fire and electric shock. Ventilate room before operating air conditioner if there is a gas leakage from another appliance. Do not direct airflow at room occupants only. Always install circuit breaker and a dedicated power circuit. Do not open the unit during operation. It may cause electric shock. Do not use the power cord near flammable gas or combustibles, such as gasoline, benzene, thinner, etc. It may cause an explosion or fire. Do not disassemble or modify unit. It may cause failure and electric shock. It may cause explosion, fire and, burns. 2 ! CAUTION Do not clean the air conditioner with water. When the air filter is to be removed, do not touch the metal parts of the unit. It may cause an injury. ! When the unit is to be cleaned, switch off, and turn off the circuit breaker. Do not clean unit when power is on as it may cause fire and electric shock, it may cause an injury. ! Stop operation and close the window in storm or hurricane. Operation with windows opened may cause wetting of indoor and soaking of household furniture. Do not place obstacles around air-inlets or inside of air-outlet. It may cause failure of appliance or accident. Do not use strong detergent such as wax or thinner but use a soft cloth. Appearance may be deteriorated due to change of product color or scratching of its surface. ! Ventilate the room well when used together with a stove, etc. Water may enter the unit and degrade the insulation. It may cause an electric shock. Do not put a pet or house plant where it will be exposed to direct air flow. An oxygen shortage may occur. This could injure the pet or plant. Do not use this air conditioner to preserve precision devices, food, pets, plants, and art objects. It may cause deterioration of quality, etc. ! Turn off the main power switch when not using the unit for a long time. Hold the plug by the head of the power plug when taking it out. ! Do not use for special purposes. It may cause electric shock and damage. ! Ensure that the installation bracket of the outdoor appliance is not damaged due to prolonged exposure. If bracket is damaged, there is concern of damage due to falling of unit. Do not place heavy object on the power cord and ensure that the cord is not compressed. There is danger of fire or electric shock. ! Use caution when unpacking and installing. Sharp edges could cause injury. ! Clean the evaporator once every three months by professional people. ! Otherwise it may cause failure of electric heating feature. 3 It may cause failure of product or fire. ! Always insert the filters securely. Clean filter once every two weeks. Operation without filters may cause failure. Do not drink water drained from air conditioner. It contains contaminants and could make you sick. If water enters the unit, turn the unit off at the power outlet and switch off the circuit breaker. Isolate supply by taking the power-plug out and contact a qualified service technician. IMPORTANT SAFETY INSTRUCTIONS WARNING NOTE The power supply cord with this air conditioner contains a current detection device designed to reduce the risk of fire. Please refer to the section Operation , of Current Device for details. In the event that the power supply cord is damaged, it cannot be repaired-it must be replaced with a cord from the Product Manufacturer. , Do not, under any circumstances, cut, remove, or bypass the grounding prong. Power supply cord with 3-prong grounding plug and current detection device For your safety Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. Avoid fire hazard or electric shock. Do not use an extension cord or an adaptor plug. Do not remove any prong from the power cord. WARNING Electrical Infor mation Be sure the electrical service is adequate for the model you have chosen. This information can be found on the serial plate, which is located on the side of the cabinet and behind the grille. Be sure the air conditioner is properly grounded. To minimize shock and fire hazards, proper grounding is important. The power cord is equipped with a three-prong grounding plug for protection against shock hazards. Your air conditioner must be used in a properly grounded wall receptacle. If the wall receptacle you intend to use is not adequately grounded or protected by a time delay fuse or circuit breaker, have a qualified electrician install the proper receptacle. Ensure the receptacle is accessible after the unit installation. Do not run air conditioner without side protective cover in place. This could result in mechanical damage within the air conditioner. Do not use an extension cord or an adapter plug. NOTE: The shape may be different according to its model: Power Card Power Suppy 230V,15A 230V,20A 230V,30A 4 265V,15A 265V,20A 265V,30A Operation of Cur rent Device(optional) The power supply cord contains a current device that senses damage to the power cord. To test your power supply cord do the following: 1. Plug in the Air Conditioner. 2. The power supply cord will have TWO buttons on the plug head. Press the TEST button, you will notice a click as the RESET button pops out. 3. Press the RESET button, again you will notice a click as the button engages. 4. The power supply cord is now supplying electricity to the unit. (On some products this it also indicated by a light on the plug head.) NOTES: Do not use this device to turn the unit on or off. Always make sure the RESET button is pushed in for correct operation. The power supply must be replaced if it fails reset when either the TEST button is pushed, or it cannot be reset. A new one can be obtained from the product manufacturer. If power supply cord is damaged, it cannot be repaired. It MUST be replaced by one obtained from the product manufacturer. When 265V units are to be installed,the power supply must be permanent wiring.Permanent wiring may be done through the accessory subbase.An exposed cord connection on 265V units are not permitted. AIR CONDITIONER FEATURES This unit has many featrues.The servicer must be familiar with these features in order to properly service the unit. Compressor Restart Delay This feature extends the overall life of compressor by preventing the short-cycling of the air conditioner.When the compressor restarts,the unit is designed to give a minimum of three minutes to have a time of equalizing the refrigerant pressures for optimizing cycling. Memory The unit has memory .If power is lost,all of the control settings(mode,fan speed,on/off and configuration) are remembered.So when power is restored,the unit will start back up in the mode (and configuration) it was in,when power was lost. Automatic Evaporator Freeze Protection Automatically to keep the evaporator from freezing,the compressor is tuuned off and the indoor fan is turned on when the evaporator temperature is too lower.If the evaporator temperature is not too lower this function is off. 5 Automatic Quick Warm-up (for heat pump models only) If the room temperature falls to 4.5 OC/8 OF below the set point temperature,the reverse cycle heat is shut off and the electric strip heat is turned on for one cycle,until heating is satisfied. LED Indicators and Buttons The touch pad has buttons for MODE,FAN, POWER,SETPOINT UP and SETPOINT DOWN. It also has LEDs that correspond to the mode, fan speed,power, and setpoint operation,to indicate the unit s status.LEDs for HIGH,MED and LOW indicate the fan speed that is selected. LEDs for FAN,COOL and HEAT indicate what operating mode is active.LED for POWER is the unit ON/OFF status LED.If the unit is in ON mode, the LED will be green.If the unit is OFF,the LED will be off. NOTE: HEAT mode is for Cooling & Heating models only. High Temperature Protection In Heating Operation The compressor and(or) electric heater will be switched off to prevent damage in high indoor blow air temperature or error indoor temperature sensor. Unit Configuration O F or OC The unit can display in either OF or OC. CONTROL PANEL OPERATION The control panel keypad will look like the following Fig.1: UP/DOWN BUTTONS ( / ) - Push the UP (or DOWN) button to increase (or decrease) the set temperature of the unit in cooling or heating mode.The temperature can be set by increments of 1OC (1OF).The setting temperature appears in the display. NOTE:Press and hold and buttons together for 3 seconds will alternate the temperature display between OC & OF scale. Fig.1 POWER - Press the POWER button to turn the unit on or off. When the unit is on,the power indicator light will be green.When the unit is off,the light will go out. MODE - Push this button to cycle through the modes from COOL-HEAT-FAN-COOL.The indicator light beside the "MODE" option will illuminate, identifying the mode selected. - COOL:The range of set temperature is 17OC/62OF ~30OC/86OF.Cooling begins automatically when the room temperature is above the set point,and stops when the room temperature is 2OC(4OF) below the set point.But the compressor will run 5 minutes at least in COOL mode before stoping. The fan runs in continuous mode. - HEAT:The range of set temperature is 17OC/62OF ~29OC/84OF.For heat pump models,the unit can alternate to run between in reverse cycle heat mode and electric heater mode according to the difference between the setting temperature and the room temperature.The fan motor cycles on and off with the compressor and electric heater. NOTE: The reverse cycle and electric heater cannot be run at the same time. In following cases, it is normal that the reverse cycle does not operate. 1.When the outdoor temperatrue is lower than 4OC/40OF or the room temperature falls to 4.5OC/8OF below the set point temperature. 2.There is a 3-minute minimum compressor run time at any setting to prevent short cycling. The indoor fan motors starts before the compressor and stops after the compressor cycles off. 3.When frost builds up to the evaporator coils, the unit will defrost automatically and the compressor will cycle off. - FAN:Fan operation only without heating and cooling. 6 FAN (FAN SPEED) - Every time you push this button,the fan speed cycles through the settings as follows:HIGH-MEDLOW-HIGH. DISPLAYS: - Shows the set temperature in OC or OF. While on Fan only mode,it shows the room temperature. Control code (on some models): LC-Pads on the control panel is not available.The unit can be setted by using wire cotroller only. Error codes: AS-Room temperature sensor error; ES-Evaporator temperature sensor error; CS-Condenser temperature sensor error; OS-Outside temperature sensor error; HS-Exhaust temperature sensor error; NOTE:When error occurs,unplug the unit and plug it back in.If error repeats, call for service. Other codes: LO-Room temperature is lower than 0OC/32OF; HI-Room temperature is higher than 37OC/99OF. NOTE: All the illustrations in this manual are for explanation purpose only. Your air conditioner may be slightly different. The actual shape shall prevail. NOTE:This air conditioner is designed to be operated under condition as follows: Cooling operation Outdoor temp: Indoor temp: 18-43OC/64-109OF (18-52OC/64-125OF for special tropical models) O O Heating Outdoor temp: operation Indoor temp: O 17-32 C/62-90 F O -5-24 C/23-76 F 0-27 C/32-80OF O Note: Performance may be reduced outside of these operating temperatures. INSTALLATION HOW TO INSTALL THE UNIT Dimension of air conditioner ! CAUTION 1067mm/4 2in ch There are sharp edges that can cause serious cuts. When lifting the air conditioner,it is HEAVY.Use 2 people to lift. 408mm/1 6in ch - For existing sleeve,you should measure the wall sleeve dimensions. - Install the new air conditioner according to these installation instructions to achieve the best performance. All wall sleeves used to mount the new air conditioner must be in good structural condition and have a rear grille that securely attaches to the sleeve or the flange of the sleeve to secure the new air conditioner. - To avoid vibration and noise,make sure the unit is installed securely and firmly. - When installing the sleeve,make certain there is nothing within 20 of the back that would interfere with heat radiation and exhaust air flow. (See Fig.2) 606mm/2 3.9 in ch Dimension of sleeve assembly (optional) 1067mm/4 2in ch 408mm/1 6in ch 376mm/1 4.8 in ch COOLED AIR WALL SLEEVE HEAT RADIATION Shipping tape Over 20 INTAKE AIR WALL Fig.3 Fig.2 PREPARATION OF SLEEVE ASSEMBLY(optional) - Refer to the installation instruction of sleeve assembly for details. PREPARATION OF REAR GRILLE ASSEMBLY(optional) - Refer to the installation instruction of rear grille assembly for details. UNIT INSTALLATION - Carefully remove shipping tapes from the front panel. (See Fig.3) - Pull out at the bottom to release it from the tabs - Then lift up . Fig.4 Shipping screw - Remove the front panel. (See Fig.4) 2 - Remove the shipping screw from the vent door.(See 1 Fig.5) 7 2 1 Fig.5 . INSTALLATION（CONTINUED） UNIT INSTALLATION (CONTINUED) - Rotate the vent control lever to either open or close the vent door.(See Fig.6) Vent control lever Vent closed Vent open Fig.6 NOTE:When vent control lever set at CLOSE,only the air inside the room is circulated and filtered. When set at OPEN,some outdoor air will be drawn into room.This will reduce heating or cooling efficiency. - Lift unit level and slide unit into wall sleeve until firmly against front of wall sleeve and secure with 4 screws and washers (supplied in the SLEEVE ASSEMBLY ) through the unit flange holes. (See Fig.7 and Fig.8) Fig.7 Fig.8 - Reinstall front panel.(See Fig.9) Place tabs over top rail . Push Inward at bottom until panel snaps into place . Fig.9 1 8 2 2 1 ! CAUTION Do not put obstacles around air-inlet or inside of air-outlet of the unit, such as window curtain etc. Always insert the filter securely, clean filter once every two weeks as required. CARE AND CLEANING FRONT PANEL AND CASE - Turn unit off and disconnect power supply.To clean, use water and a mild detergent.DO NOT use bleach and abrasivers.Some commercial cleaners may damage the plastic parts. OUTDOOR COIL - Coil on outdoor side of unit should be checked regularly.Unit will need to be removed to inspect dirt build-up that will occur on the inside of the coil. If clogged with dirt and soot ,coil should be professionally cleaned.Clean inside and outside of outdoor coils regularly. NOTE: Never use a high-pressure spray on coil. ! CAUTION - Removing Air Filter 2 Air filters Pull up Fig.9 - Replacing Air Filter Push down UNIT DAMAGE HAZARD Failure to follow this caution may result in equipment damge or improper operation. Airflow restriction may cause damage to the unit. Fig.10 AIR FILTERS IMPORTANT:TURN UNIT OFF BEFORE CLEANING. VENT DOOR FILTER IMPORTANT:TURN UNIT OFF BEFORE CLEANING. ! CAUTION UNIT DAMAGE HAZARD Failure to follow this caution may result in equipment damge or improper operation. Do not operate unit without filters in place.If a filter becomes torn or damaged,it should be replaced immediately. Operating without filters in place or with damaged filter will allow dirt and dust to reach indoor coil and reduce cooling,heating,airflow and efficiency of unit. Airflow restriction may cause damage to unit. - The most important thing you can do to maintain unit efficiency is to clean the filters once every two weeks as required. Clogged filters reduce cooling,heating and airflow. - Keeping filters clean will: Decrease cost of operation. Save energy. Prevent clogged indoor coil. Reduce risk of premature component failure. - To Clean Air Filters: Vacuum off heavy soil. Run water through filter. Dry thoroughly before replacing. - If the vent door is open,access requires the removal of the unit from the wall sleeve.Clean the vent filter twice a year or as required. - Make sure to remove the shipping screw from the vent door.(See.Fig.5) - Rotate the vent control lever to open the vent door. (See. Fig.6) - Remove four screws from the vent door filter. (See.Fig.11) - First pull out the vent door steel wire from the hole of the vent door, then take off the vent door and filter. (See.Fig.11) - Clean the filter.Dry thoroughly before replacing. - Replac the vent door and filter,reinstall the four screws. - Reinsert the vent door steel wire into the hole of the vent door. Vent door control lever . Screws Vent door steel wire Vent door filter Fig.11 9 Vent door TROUBLESHOOTING POSSIBLE CAUSES UNIT DOES NOT START Unit may have become unplugged Fuse may have blown Circuit breaker may have been tripped Unit may be off Unit may be in a protection mode. UNIT NOT COOLING/HEATING ROOM Unit air discharge section is blocked Temperature setting is not high or low enough Note:Setpoint limits may not allow the unit to heat or cool the room to the temperature desired.Check section on dipswitch settings. Unit air filters are dirty. Room is excessively hot or cold when unit is started. Vent door left open. Unit may be in a protection mode. Compressor is in time delay. DISPLAY HAS STRANGE NUMBERS/ CHARACTERS ON IT UNIT MAKING NOISES SOLUTONS Check that plug is plugged securely in wall receptacle. Note:Plug has a test/reset button on it.Make sure that the plug has not tripped. Replace the fuse.See Note 1. Reset circuit breaker.See Note 1. Turn unit on (bottom right button on keypad). Make sure that curtains,blinds or furniture are not restricting or blocking unit airflow. Reset to a lower or higher temperature setting. Remove and clean filters. Allow sufficient amount of time for unit to heat or cool the room.Start heating or cooling early before outdoor temperature,cooking heat or gatherings of people make room uncomfortable. Close vent door. Check dipswitch settings for desired comfort. Wait approximately 3 minutes for compressor to start. The unit may be in a protection mode. The unit may be set for OC (instead of OF). Clicking,gurging and whooshing noises are normal during operation of unit. WATER DRIPPING OUTSIDE If a drain kit has not been installed,condensation runoff during very hot and humid weather is normal.See Note 2.If a drain kit has been installed and is connected to a drain system,check gaskets and fittings around drain for leaks and plugs. WATER DRIPPING INSIDE Wall sleeve is not installed level Wall sleeve must be installed level for proper drainage of condensation .Check that installation is level and make any necessary adjustments. ICE OR FROST FORMS ON INDOOR COIL Low outdoor temperature Dirty filters When outdoor temperature is approximately 55OF or below,frost may form on the indoor coil when unit is in Cooling mode.Switch unit to FAN operation until ice or frost melts. Remove and clean filters. COMPRESSOR PROTECTION Power may have cycled,so compressor is in a restart protection. Random Compressor restart-Whenever the unit is plugged in,or power has been restarted,a random compressor restart will occur. After a power outage,the compressor will restart after approximately 3 minutes. Compressor Protection-To prevent short cycling of the compressor, there is a random startup delay of 3 minutes and a minimum compressor run time of 3 minutes. Clean the evaporator once every three months by professional people. ELECTRIC HEATING FAILURE NOTES: 1.If circuit breaker is tripped or fuse is blown more than once,contact a qualified electrician. 2.If unit is installed where condensation drainage could drip in an undesirable location,an accessory drain kit should be installed and connected to drain system. 10 www.cooperandhunter.us LIMITED WARRANTY STATEMENT PACKAGED TERMINAL AIR CONDITIONER This warranty should be registered on our web-site www.cooperandhunter.us The warranty is only valid when installed by a Licensed HVAC Technician FOR WARRANTY SERVICE OR REPAIR: Contact your installing contractor. You may find the installer’s name on the equipment or in your Owner’s packet. Complete product registration below and send back by e-mail at [email protected] PRODUCT REGISTRATION: Model No.: ______________________________________________________________________________________________ Serial No.: _______________________________________________________ Date of Installation: ______________________ Owner Name: ____________________________________________________________________________________________ Address of Installation:_____________________________________________________________________________________ Installing Contractor: ______________________________________________________________________________________ Address: ________________________________________________________________________________________ Phone No. / E-mail: _______________________________________________________________________________ Place Of Purchase: ________________________________________________________________________________________ Date of Purchase: _______________________________________________________________________________ C&H distributor (hereinafter “Company”) warrants this product against failure due to defect in materials or workmanship under normal use and maintenance as follows. All warranty periods begin on the date of original installation. If the date cannot be verified, the warranty period begins one hundred twenty (120) days from date of manufacture. Damage resulting from failure to use, install or maintain the product in a manner consistent with our/manufacturer’s recommendations shall render the warranty void. Cooper&Hunter, at its option, may request a report from a qualified technician prior to honoring a warranty claim. If a part fails due to defect during the applicable warranty period Company will provide a new or remanufactured part, at Company’s option, to replace the failed defective part at no charge for the part. This limited warranty is subject to all provisions, conditions, limitations and exclusions listed below. ● A warranty period of Seven (7) years on compressor to the original registered end-user. ● A warranty period of Five (5) years on all parts to the original registered end user. ● A warranty period of One (1) year on the remote control provided with the original unit. ● Limited warranty applies only to systems that are properly installed by a state certified or licensed HVAC contractor, under applicable local and state law in accordance with all applicable building codes and permits; C&H installation and operation instructions and good trade practices. ● Warranty applies only to products remaining in their original installation location. ● Defective parts must be returned to the distributor through a registered servicing dealer for credit. LIMITATIONS OF WARRANTIES: ALL IMPLIED WARRANTIES AND/OR CONDITIONS (INCLUDING IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR USE OR PURPOSE) ARE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY. SOME STATES OR PROVINCES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY OR CONDITION LASTS, SO THE ABOVE MAY NOT APPLY TO YOU. THE EXPRESS WARRANTIES MADE IN THIS WARRANTY ARE EXCLUSIVE AND MAY NOT BE ALTERED, ENLARGED, OR CHANGED BY ANY DISTRIBUTOR, DEALER, OR OTHER PERSON, WHATSOEVER. THIS WARRANTY DOES NOT COVER: 1. Labor or other costs incurred for diagnosing, repairing, removing, installing, shipping, servicing, or handling of defective parts, replacement parts, or new units. 2. 3. Product cleaning required prior to warranty service and repair. Normal maintenance as outlined in the installation and servicing instructions or user's manual, including filter cleaning and/or replacement and lubrication. Failure, damage, or repairs due to faulty installation, misapplication, abuse, improper servicing, unauthorized alteration, or improper operation. Failure to start due to voltage conditions, blown fuses, open circuit breakers, or damages due to the inadequacy or interruption of electrical service. Failure or damage due to floods, winds, fires, lightning, accidents, corrosive environments (rust, etc.), or other conditions beyond the control of Company. Failure or damage of coils or piping due to corrosion on installations within one (1) mile of a sea coast or a corrosive body. Parts not supplied or designated by Company, or damages resulting from their use. Products installed outside the continental USA and Canada. Electricity or fuel costs, or increases in electricity or fuel costs for any reason whatsoever, including additional or unusual use of supplemental electric heat. Any cost to replace, refill, or dispose of refrigerant, including the cost of refrigerant. Shipping damage or damage as a result of transporting the unit. Accessories such as condensate pumps, line sets, and so forth. Any special, indirect, or consequential property or commercial damage of any nature whatsoever. Some states or provinces do not allow the exclusion of incidental or consequential damages, so the above limitation may not apply to you. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project