Frigidaire | FGPC1044U1 | Use & care guide | Frigidaire FGPC1044U1 Use & Care Guide

Frigidaire FGPC1044U1 Use & Care Guide
All about the
Use & Care
of your
Portable Air Conditioner
TA B L E O F C O N T E N T S
Important Safety Instructions ............................... 2-3
Installation Instructions ........................................ 7-8
FCC Statement .................................................... 4
Air Conditioner Features ...................................... 9
Product Registration ............................................. 5
Operating Instructions ......................................... 10-12
Normal Sounds .................................................... 5
Care and Cleaning ............................................... 12
Unit Description ................................................... 6
Before You Call ................................................... 13
Accessories Included ............................................ 6
Major Appliance Limited Warranty ........................ 14
www.frigidaire.ca Canada 1-800-265-8352
16120600A09454 (June 2009)
www.frigidaire.com USA 1-800-944-9044
Important Safety Instructions
NOTE:
This USE & CARE MANUAL provides specific operating instructions for your model. Use the Portable air conditioner only as
instructed in this USE & CARE MANUAL. These instructions are not meant to cover every possible condition and situation that
may occur. Common sense and caution must be practiced when installing, operating, and maintaining any appliance.
NOTE:
WARNING
The power supply cord with
this air conditioner contains a current
detection device designed to reduce the risk
of fire.
Please refer to the section ‘Operation of
Current Device’ for details.
In the event that the power supply cord is
damaged, it cannot be repaired. It must be
replaced with a cord from the product
manufacturer.
WARNING
Avoid fire hazard or electric shock. Do not
use an extension cord or an adaptor plug. Do
not remove any prong from the power cord.
Grounding type wall
receptacle
Do not, under any
circumstances, cut,
remove, or bypass the
grounding prong.
For Your Safety
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any
other appliance. Read product labels for flammability and other warnings.
WARNING
Prevent Accidents
To reduce the risk of fire, electrical shock, or injury to persons when using your air conditioner,
follow basic precautions, including the following:
Be sure the electrical service is adequate for the model you have chosen. This information
can be found on the serial plate, which is located on the side of the cabinet.
If the air conditioner is to be installed in a window, you will probably want to clean both
sides of the glass first.
Be sure the air conditioner has been securely and correctly installed according to the
installation instructions in this manual. Save this manual for possible future use in
removing or reinstalling this unit.
WARNING
Electrical Information
The complete electrical rating of your new protable air conditioner is stated on the serial
plate. Refer to the rating when checking the electrical requirements.
Be sure the air conditioner is properly grounded. To minimize shock and fire hazards,
proper grounding is important. The power cord is equipped with a three-prong grounding
plug for protection against shock hazards.
Your air conditioner must be used in a properly grounded wall receptacle. If the wall
receptacle you intend to use is not adequately grounded or protected by a time delay fuse
or circuit breaker, have a qualified electrician install the proper receptacle.
Power supply cord
with 3-prong grounding
plug and current
detection device
Do not run air conditioner without outside protective cover in place. This could result in
mechanical damage within the air conditioner.
Do not use an extension cord or an adapter plug.
SAFETY PRECAUTIONS
DANGER! Avoid Serious Injury or Death
This air conditioner contains no user-serviceable parts. Always call an authorized Electrolux servicer for repairs.
Do not insert or place fingers or objects into the air discharge area on top of the unit.
Do not start or stop the air conditioner by unplugging the power cord or turning off the power at the electrical box.
Do not cut or damage the power cord.
If the power cord is damaged, it should only be replaced by an authorized Electrolux servicer.
In the event of a malfunction (sparks, burning smell, etc.), immediately stop the operation, disconnect the power cord, and call an authorized
Electrolux servicer.
Do not operate the air conditioner with wet hands.
Do not pull on the power cord.
Do not drink any water that is drained from the air conditioner.
2
2009 Electrolux Home Products, Inc.
All rights reserved.
Important Safety Instructions
SAFETY PRECAUTIONS
CAUTION! Avoid Injury or damage to the unit or other property
Provide occasional ventilation during use. Do not direct airflow at fireplaces or other heat related sources as this could cause flare ups or make
units run excessively.
Do not climb on or place objects on the unit.
Do not hang objects off the unit.
Do not place containers with liquids on the unit.
Turn off the air conditioner at the power source when it will not be used for an extended period of time.
Periodically check the condition of the unit’s installation accessories for any damage.
Do not apply heavy pressure to the radiator fins of the unit.
Operate the unit with air filter in place.
Do not block or cover the intake grille, discharge area and outlet ports.
Ensure that any electrical/electronic equipment is one yard away from the unit.
Do not use or store flammable gases near the unit.
READ THIS SECTION BEFORE ATTEMPTING TO OPERATE AIR CONDITIONER.
Unit must be upright for one hour prior to operating.
The power supply cord contains a current device that senses damage to the power cord. To test
your power supply cord do the following:
Plug in &
press RESET
Plug in the Air Conditioner.
The power supply cord will have TWO buttons on the plug head. Press the TEST button. You will
notice a click as the RESET button pops out.
Press the RESET button. Again you will notice a click as the button engages.
The power supply cord is now supplying electricity to the unit.(On some model, this is also
indicated by a light on the plug head)
NOTE:
Do not use this device to turn the unit on or off.
Always make sure the RESET button is pushed in for correct operation.
The power supply cord must be replaced if it fails to reset when either the TEST button is pushed,
or it cannot be reset. A new one can be obtained from the product manufacturer.
If power supply cord is damaged, it CANNOT be repaired. It MUST be replaced by one obtained
from the product manufacturer.
2009 Electrolux Home Products, Inc.
All rights reserved.
3
FCC Statement
FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by tuning the device off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the device and receiver.
Connect the equipment into an outlet other than the one used for the receiver.
Consult the dealer or an experienced radio/TV technician for assistance.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) This device must accept any interference received, including interference that may cause
undesired operation.
FCC CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
Host device Labeling
This device includes the following module.
Contains FCC ID: 2AIBX-WD115
RF exposure statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be
installed and operated with minimum 20 cm between the radiator and your body. This transmitter must not be collocated or
operating in conjunction with any other antenna or transmitter unless authorized to do so by the FCC.
INDUSTRY CANADA (IC) STATEMENT
This Class B digital apparatus complies with Canadian ICES-003.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
RF Exposure
The antenna (or antennas) must be installed so as to maintain at all times a distance minimum of at least 20 cm between the
radiation source (antenna) and any individual. This device may not be installed or used in conjunction with any other antenna
or transmitter.
l'exposition aux RF
L’antenne (ou les antennes) doit être installé e de façon à maintenir à tout instant une distance minimum de au moins 20 cm entre la
source de radiation (l’antenne) et toute personne physique.
Host device Labeling
This device includes the following module.
Contains IC: 21700-NIUX
Host dispositif d'étiquetage
Ce dispositif inclut le module suivant.
Contient module émetteur IC: 21700-NIUX
This is the location
of the module.
4
2009 Electrolux Home Products, Inc.
All rights reserved.
Product Registration & Normal Sounds
Product Registration
Record Your Model and Serial Numbers
Record in the space provided below the model and serial numbers. On all models, the
serial plate is located on the side of the cabinet.
Model No.
Serial No.
Register Your Product
The self-addressed PRODUCT REGISTRATION CARD should be filled in completely,
signed and returned to the Frigidaire Company.
Normal Sounds
Sound of Rushing Air
At the top of the unit, you may
hear the sound of rushing air
being moved by the fan.
Gurgle/Hiss
“Gurgling or hissing” noise may be
heard due to refrigerant passing
through evaporator during normal
operation.
High pitched Chatter
Vibration
Today’s high efficiency
compressors may have a
high pitched chatter during
the cooling cycle.
Unit may vibrate and make noise
because of uneven floor.
2009 Electrolux Home Products, Inc.
All rights reserved.
5
Unit Description & Accessories Included
Unit Description
ROOM AIR DISCHARGE
CARRYING HANDLE
(BOTH SIDES)
HIDDEN DISPLAY
REMOTE SIGNAL
RECEIVER
FILTER
AIR INTAKE
EXHAUST
AIR OUTLET
CONTROL PANEL
DEHUMIDIFYING
DRAIN OUTLET
REMOTE CONTROL
CASTOR
Fig. 1
BOTTOM TRAY
DRAIN OUTLET
Accessories Included
PARTS:
PARTS NAME:
QUANTITY:
Exhaust hose
1 pc
Window Sliding Kit
1 set
Foam Seal A
2 pcs
Foam Seal B
1 pcs
Spared Extend Rod
1 pc
3/8” Screw
1 pcs
Decoration Film
1 pcs
Safety Lock
1 pc
Remote Control
1 pc
Fig. 2
Check all the accessories are included in the package and please refer to the installation
instructions for their usage.
6
2009 Electrolux Home Products, Inc.
All rights reserved.
Installation Instructions
Installation Instructions
EXHAUSTING HOT AIR
In the COOLING Mode the appliance must be placed close to a window or
opening so that the warm exhaust air can be ducted outside.
Adapter B
First position unit on a flat floor and make sure there’s a minimum of 12"
clearance around the unit, and is within the vicinity of a single circuit outlet
power source. It is recomended to have a 50” clearance in the back of the
unit.
Adapter A
Extend the side of hose
Fig. 3
1. Extend either side of the hose (Fig. 3).
2. Slide the adaptor A into the excharge hole of the unit as shown on Fig. 4.
3. Install the window kit on the window and slide the adaptor B into the
window slider kit and seal. (Fig. 5 & 6)
NOTE: Refer to page 8 about how to install the window kit.
Fig. 4
Vertical
window
Horizontal
window
Window Slider Kit
Minimum:22.1"(560mm)
Maxmum:44.1"(1120mm)
Fig. 5
Window Slider Kit
Minimum:22.1"(560mm)
Maxmum:44.1"(1120mm)
Fig. 6
The hose can be extended from its original length of 15" up to 59", but it is the best to keep the length to minimum required.
Also make sure that the hose does not have any sharp bends or sags. (Fig. 7)
Fig. 7
2009 Electrolux Home Products, Inc.
All rights reserved.
7
Installation Instructions
Installation Instructions
(continued)
Installation in a double-hung sash/sliding sash window
1. Cut the foam seals A(adhesive type) to the proper lengths and attach them to the window and stool (Fig. 8).
2. Open the window sash and lift the locking lever of the window slider kit (Fig. 9), then place the window slider kit on the
window stool. Adjust the length of the window slider kit according to the width of window (Fig. 10).
Locking lever
Window
slider kit
Foam seal A
(adhesive type)
Fig. 9
Fig. 8
Fig. 10
NOTE: If the window is too wide, you can replace the pre-installed telescopic rod with the spared extend rod or
combine the 2 rods. The recommended usage of the rods are as below:
t8JUINNQSFJOTUBMMFEUFMFTDPQJDSPEPOMZBWBJMBCMFSBOHFNNNN
t8JUINNTQBSFEFYUFOESPEPOMZBWBJMBCMFSBOHFNNNN
t8JUIUIFDPNCJOBUJPOBWBJMBCMFSBOHFNNNN
To replace the pre-installed telescopic rod with the spared extend rod, first take out the telescopic rod
completely(Fig.11 A). Then take down the cap from the pre-installed telescopic rod and put it on the spared extend
rod.
To combine the 2 rods, first take out the telescopic rod completely(Fig.11 A). Then align the 3 hooks on the extending
rod to the 3 slots on the end of the telescopic rod and slide the 3 hooks into the slots, then press down the extending
rod to lock the slots(Fig.11 B). After that slide the combined telescopic rod back into the window kit(Fig.11C).
Fig. 11 A
Fig. 11 C
Fig. 11 B
3. Press back the locking lever to fix the longth of the window slider kit then
close the window sash securely against the window slider kit (Fig. 12).
4. To secure lower sash, attach sash lock with 3/8” (9.5mm)
screw as shown Fig. 13.
NOTE: It is difficult to lock the windows with the sash lock for Vinyl-Clad
windows, so you can use lock by window itself.
Fig. 12
5. Cut the foam seal B(adhesive type) to an appropriate length and seal the open gap between
the top window sash and outer window sash, as shown in Fig. 14.
6. Cut the decoration film to an appropriate length and stick on the extending
rod channel(Fig. 15).
Sash lock
Foam seal B(adhesive type)
Fig. 13
8
Decoration
film
2009 Electrolux Home Products, Inc.
Fig. 14
Fig. 15
All rights reserved.
Air Conditioner Features
Air Conditioner Features
CONTROL PANEL
TURNS UNIT SETS MODE
ON OR OFF
DISPLAYS
TEMPERATURE/TIME
ADJUSTS
TEMPERATURE
OR TIME
Fig. 18
SETS FAN FILTER RESET
SPEED
BUTTON
HOLD 3 SECS
TO RESET
CONNECT
BUTTON
NOTE: Please see Quick Start Guide for how to download the Frigidaire® - Smart Appliance APP and find out more detail
about how to connect the unit and use the “Scheduler” function in the APP.
REMOTE CONTROL
MODE SELECTOR
To replace the battery
Protecting cover
TEMPERATURE
BUTTON
Battery
Back cover
On/Off
BUTTON
Fig. 20
FAN SPEED SELECTOR
Fig. 19
Note: Open the back covers and
remove the protecting film to
activate the remote control, when
use for the first time.
Be sure the batteries are inserted properly.
Do not use batteries other than the type specified.
Do not use old batteries with new ones .
Do not dispose of batteries in fire. Batteries may
explode or leak.
5. To prevent damage, remove the batteries when not
being used for a long time.
6. This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
2009 Electrolux Home Products, Inc.
Fig. 22
Turn over the remote control. In the button of the remote control there is
a slot. Use a coin or something like that to rotate the back cover
anti-clockwise to open it.(Fig.20 & 21) Use the same way to open the
protecting cover inside and take out the battery.(Fig.22) Replace the battery
and reinstall the inside cover and back cover.
Note: Place battery in tray with POSITIVE(“+”) side facing UP.
Battery Type: RG15D/E-ELL (Rated Voltage:3VDC)
Warning:
1.
2.
3.
4.
Fig. 21
WARNING: Chemical Burn Hazard. Keep batteries
away from children.
This product contains a lithium button/coin cell battery. If
a new or used lithium button/coin cell battery is swallowed
or enters the body, it can cause severe internal burns and
can lead to death in as little as 2 hours. Always
completely secure the battery compartment. If the
battery compartment does not close securely, stop using
the product, remove the batteries, and keep it away from
children. If you think batteries might have been swallowed
or placed inside any part of the body, seek immediate
medical attention. The cells shall be disposed of properly,
including keeping them away from children; Even used
cells may cause injury.
All rights reserved.
9
Operating Instructions
Operating Instructions
NOTE
The following instructions represent the Control Panel and some functions can only be selected by using the
control panel.
COOLING MODE:
In this mode the exhaust adaptor hose MUST be used.
1. Press the "modes" button until the "cool" indicator lights.
2. Press the " - " & " + " Temp buttons for desired setting.
3. Press the "fan speed" button for desired fan speed.
DRY MODE:
In this mode you do not need to use the exhaust adaptor hose, BUT the water
collected must be discharged. See Drainage Section.
1. Press the "modes" button until the "dry" indicator lights.
2. The fan will run at low speed and the display will show the room temperature.
3. Keep doors & windows closed for best effect.
ECO MODE:
Always have the exhaust hose attached in this mode.
The unit will run in energy saver(econ) mode when used for the first time. In this mode,
the fan will continue to run for 3 minute after the compressor shuts off. The fan then
cycles on for 90 seconds at 10 minutes intervals until the room temperature is above the
set temperature, at which time the compressor turns back on.
FAN MODE:
In this mode there is no need to use the exhaust hose or drainage hose.
However, if you require stale or smokey air to be removed from the room,
hook up the duct accessories as described in the "EXHAUSTING HOT AIR"
section.
1. Press the "modes" button until the "fan" indicator lights.
2. Press the "fan speed" button to choose the desired fan speed.
3. The fan will run at the selected speed and the display will show the room temperature.
CHECK FILTER FEATURE:
This feature is a reminder to clean the Air Filter (See Care and Cleaning) for more
efficient operation. The filter indicator will illuminate after 250 hours of operation.
To reset after cleaning the filter, press and hold the "filter" button for 3 seconds
and the light will go off.
SELECTING FAN SPEED:
You can select the desired fan speed, by pressing the "fan speed" button. The fan
speed will change in the sequence as the drawing on the left.
auto fan
lo
hi
med
NOTE: After choosing the fan speed as "auto fan", "lo", "med" or "hi", the
cooresponding fan speed indicator light will illuminate. Under Dry mode, you can not
select the fan speed.
DEACTIVATE WIF MODULE: The wifi module can be deactivated by holding the "Connect button" and " - "
synchronously 3 seconds. Press the "Connect button" again to activate the
wifi module again. It will take about 30 seconds for the module to initiate again.
10
2009 Electrolux Home Products, Inc.
All rights reserved.
Operating Instructions
Operating Instructions
(continued)
FAULT CODE:
If the display reads "AS" , the room temperature sensor has failed. Contact your Authorized
Frigidaire Service Center.
If the display reads "ES" , the evaporator temperature sensor has failed. Contact your
Authorized Frigidaire Service Center.
If the display reads "E4" , the display panel communication has failed. Contact your
Authorized Frigidaire Service Center.
If the display reads "P1" , bottom tray is full. Carefully move the unit to a drain location, remove
the bottom drain plug and let the water drain away. Restart the machine until the "P1" symbol
disappears. If error repeats, call for service.
If the display reads "E7", the indoor motor has failed. Contact your Authorized Frigidaire
Service Center.
DRAINAGE:
During the dry mode, you will need a garden hose (sold
separately) to drain the condensate from the unit.
Remove the rubber stopper from the hose connector, then screw on a
garden hose to the connector as shown on Fig. 23.
The hose may then:
A. Discharge into a drain that is lower than the unit.
B. Be connected to a condensate pump (sold separately).
C. During cooling mode, please replace the rubber stopper
to the hose connector to reach the maximum performance.
Garden hose
Unscrew the cap
and remove the
rubber stopper
Button drain
Fig. 23
2009 Electrolux Home Products, Inc.
All rights reserved.
11
Operating Instructions, CARE & CLEANING
Operating Instructions
(continued)
ADDITIONAL THINGS
YOU SHOULD KNOW
Now that you have mastered the operating procedure, here are more features in
your control that you should become familiar with.
The "Cool" circuit has an automatic 3 minutes time delayed start if the unit is turned
off and on quickly. This prevents overheating of the compressor and possible circuit
breaker tripping. The fan will continue to run during this time.
Temperature can be set between 60 °F and 90 °F (16 °C and 32 °C).
The control is capable of displaying temperature in degrees Fahrenheit or degrees
Celsius. To convert from one to the other and back, press and hold the "TEMP"
Up ( + ) and Down ( - ) buttons together for 3 seconds.
There is a 2-Second delay for the compressor shutting down when selecting
FAN ONLY. This is to cover the possibility of having to roll through to select another
mode.
After a power outage, the unit will memorize the last setting and return the unit to
the same setting once power is restored.
Indoor operating temperature range for this product is 60 °F to 95 °F (16 °C to 35 °C).
Wifi module can be shut down by holding the “wifi” button and “-” button simultaneously
for 3 seconds.
During normal operation, the unit's display will show room temperature but when the room
temperature is over 99 °F (37 °C) the display will show "HI".
After 60 seconds of control inactivity the display and indicator lights will turn off. Press any
button on the control panel or remote control and the display will resume.
This unit have a anion generator which can be turn on/off by using the “Clean air” feature
in the APP. When this feature is "ON", the electronic air purifier is energized to remove
pollen and impurities from the air. (This feature can be activated on the APP ONLY)
CARE & CLEANING
Clean your air conditioner occasionally to keep it looking new. Be sure to unplug
the unit before cleaning to prevent shock or fire hazards.
Air Filter Cleaning
Slide out
the filter
This unit has four filters, they are located on the back of the unit. Grasp the filters
tab and pull off the filters one by one(Fig.24).
Wash the filter using liquid dishwashing detergent and warm water. Rinse filter
thoroughly. Gently shake excess water from the filter. Be sure filter is thoroughly
dry before replacing.
Or, instead of washing you may vacuum the filter clean.
Replace the filter after the filter is dry.
Fig. 24
Cabinet Cleaning
Be sure to unplug the air conditioner to prevent shock or fire hazard. The cabinet
and front may be dusted with an oil-free cloth or washed with a cloth dampened
in a solution of warm water and mild liquid dishwashing detergent. Rinse
thoroughly and wipe dry.
Never use harsh cleaners, wax or polish on the cabinet front.
Be sure to wring excess water from the cloth before wiping around the controls.
Excess water in or around the controls may cause damage to the air conditioner.
Winter Storage
If you plan to store the appliance during the winter, cover it with plastic or return
it to its carton.
12
2009 Electrolux Home Products, Inc.
All rights reserved.
Before You Call
Before calling for service, review this list. It may save you time and expense. This list includes common occurrences that are not
the result of defective workmanship or materials in this appliance.
OCCURRENCE
Air conditioner will not operate.
SOLUTION
Wall plug disconnected. Push plug firmly into wall outlet.
Plug Current Device Tripped. Press the RESET button.
House fuse blown or circuit breaker tripped. Replace fuse with time delay type or reset circuit breaker.
Control is OFF. Turn Control ON and set to desired setting.
P1 appears in the display window. Drain water as described in Drainage Section.
Room Temperature lower than the set temperature (Cool Mode). Reset the temperature.
Air from unit does not feel cold
enough.
Room temperature below 60 °F (16 °C). Cooling may not occur until room temperature rises above
60 °F (16 °C).
Reset to a lower temperature.
Compressor shut-off by changing modes. Wait approximately 3 minutes and listen for compressor to
restart when set in the COOL mode.
Air conditioner cooling, but room
is too warm - ice forming
on cooling coil behind decorative
front
Outdoor temperature below 60 °F (16 °C). To defrost the coil, set FAN ONLY mode.
Air filter may be dirty. Clean filter. Refer to Care and Cleaning section. To defrost, set to FAN ONLY
mode.
Temperature is set too low for night-time cooling. To defrost the coil, set to FAN ONLY mode. Then,
set temperature to a higher setting.
Exhaust duct not connected or blocked. See EXHAUSTING HOT AIR Section.
Air conditioner cooling, but room
is too warm - NO ice forming on
cooling coil behind decorative
front.
Dirty air filter - air restricted. Clean air filter. Refer to Care and Cleaning section.
Temperature is set too high. Set temperature to a lower setting.
Air directional louvers positioned improperly. Position louvers for better air distribution.
Front of unit is blocked by drapes, blinds, furniture, etc. - restricts air distribution. Clear blockage in
front of unit.
Doors, windows, registers, etc. open - cool air escapes. Close doors, windows, registers, etc.
Unit recently turned on in hot room. Allow additional time to remove “stored heat” from walls, ceiling,
floor and furniture.
Air conditioner turns on and off
rapidly.
Noise when unit is cooling.
Dirty air filter - air restricted. Clean air filter.
Outside temperature extremely hot. Set FAN speed to a faster setting to bring air through cooling coils
more frequently.
Air movement sound. This is normal. If too loud, set to lower FAN setting.
Vibraion from uneven floor. Move or support appliance correctly on even surface.
Room too cold.
Set temperature too low. lncrease set temperature.
Trouble connecting the smart
Please visit Frigidaire.com and select the Owner Support section to view Frequently Asked Questions.
appliance to your wifi network or
experiencing an issue with the app.
If These Solutions Fail, Call 1-800-944-9044(US)/1-800-265-8352(Canada)
For Frigidaire Service.
2009 Electrolux Home Products, Inc.
All rights reserved.
13
Major Appliance Limited Warranty
Your appliance is covered by a limited one-year warranty and a limited 2-5 year warranty on the sealed system (the compressor,
condenser, evaporator and tubing). For one year from your original date of purchase, Electrolux will pay all costs for repairing or
replacing any parts of this appliance that prove to be defective in materials or workmanship when such appliance is installed,
used and maintained in accordance with the provided instructions. From the second to the fifth year from your original purchase
date, Electrolux will repair or replace any parts in the Sealed Refrigeration System (compressor, condenser, evaporator and tubing)
that prove to be defective in materials or workmanship. In years 2-5, the consumer will be responsible for diagnostic, labor and
parts costs as well as any removal, transportation and reinstallation expenses which are incurred during service on components
other than those covered under the Sealed Refrigeration System 5-year warranty.
Exclusions
This warranty does not cover the following:
1. Products with original serial numbers that have been removed, altered or cannot be readily determined.
2. Product that has been transferred from its original owner to another party or removed outside the USA or
Canada.
3. Rust on the interior or exterior of the unit.
4. Products purchased "as-is" are not covered by this warranty.
5. Food loss due to any refrigerator or freezer failures.
6. Products used in a commercial setting.
7. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances not
in ordinary household use or used other than in accordance with the provided instructions.
8. Service calls to correct the installation of your appliance or to instruct you how to use your appliance.
9. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves,
etc., which are not a part of the appliance when it is shipped from the factory.
10. Service calls to repair or replace appliance light bulbs, air filters, water filters, other consumables, or knobs,
handles, or other cosmetic parts.
11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry trip
charges, or mileage expense for service calls to remote areas, including the state of Alaska.
12. Damages to the finish of appliance or home incurred during installation, including but not limited to floors,
cabinets, walls, etc.
13. Damages caused by: services performed by unauthorized service companies; use of parts other than
genuine Electrolux parts or parts obtained from persons other than authorized service companies; or external
causes such as abuse, misuse, inadequate power supply, accidents, fires, or acts of God.
14. Limitations and/or restrictions on smart appliance connectivity outside Electrolux’s control including, but not
limited to, software incompatibility, inadequate home wireless network capability/range and internet availability.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR OR
REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES, INCLUDING WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST
PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE YEAR. ELECTROLUX SHALL NOT BE LIABLE FOR
CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES
RESULTING FROM ANY BREACH OF THIS WRITTEN LIMITED WARRANTY OR ANY IMPLIED WARRANTY. SOME
STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS
OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS.
YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.
If You Need Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty period
Service
should service be required. If service is performed, it is in your best interest to obtain and keep all receipts.
Service under this warranty must be obtained by contacting Electrolux at the addresses or phone numbers below.
You will be responsible for any service charges incurred due to limitations and/or restrictions on smart appliance
connectivity outside Electrolux’s control including, but not limited to, software incompatibility, inadequate home
wireless network capability/range and internet availability.
This limited warranty only applies in the USA and Canada. In the USA, your appliance is warranted by Electrolux Major Appliances
North America, a division of Electrolux Home Products, Inc. In Canada, your appliance is warranted by Electrolux Canada Corp.
Electrolux authorizes no person to change or add to any obligations under this warranty. Obligations for service and parts under
this warranty must be performed by Electrolux or an authorized service company. Product features or specifications as described
or illustrated are subject to change without notice.
USA
1.800.944.9044
Electrolux Major Appliances
10200 David Taylor Drive
Charlotte, NC 28262
14
2009 Electrolux Home Products, Inc.
Canada
1.800.265.8352
Electrolux Canada Corp.
5855 Terry Fox Way
Mississauga, Ontario, Canada
L5V 3E4
All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising