Cooper&Hunter | CH18MSPHFC230VI | Manual and User Guide | Cooper&Hunter CH18MSPHFC230VI Manual and User Guide

Cooper&Hunter CH18MSPHFC230VI Manual and User Guide
3
CONTENTS
INDOOR UNIT
PAGE
IMPORTANT SAFETY INFORMATION........................................................1
TEMPORARY OPERATIONS.....................................................................2
AIR CONDITIONER OPERATIONS AND PERFORMANCE............................3
1
HINTS FOR ECONOMICAL OPERATION.....................................................4
ADJUSTING AIR FLOW DIRECTION..........................................................4
SOPHIA
MULTI-ZONE
AU
CO
DR
HE
FAN
4
TO
OL
FOLLOWING SYMPTOMS ARE NOT AIR CONDITIONER TROUBLES..........5
TROUBLESHOOTING.................................................................................6
6
TEM
SE P
T
Y
AT
CLOC
SET
FAN
MO
M
MAINTENANCE.........................................................................................4
2
K
HOU
SPEE
R
D
DE
FAN
SPE
ED
SW
SW
AIR
ING
RESE
T LOCK
ING
C/H
DIRE
CTIO
N
CLO
OK
TIM
ECO
TIM
CK
8
7
1.
To prevent injury to the user or other people and property
damage, the following instructions must be followed. Incorrect
operation due to ignoring of instructions may cause harm or
damage.
9
The safety precautions listed are divided into two categories. In either
case, important safety information is listed which must be read.
WARNING
USER'S MANUAL
OR
Failure to observe a warning may result in death. The
appliance shall be installed in accordance with national
wiring regulations.
9
7
CAUTION
7
8
8
Failure to observe a caution may result in injury or damage
to the equipment.
9
WARNING
Ask your dealer for installation of the air conditioner.
Incomplete installation performed by yourself may result in a
water leakage, electric shock, and fire.
Models:
CH-18MSPHFC-230VI
CH-24MSPHFC-230VI
8
IMPORTANT NOTE:
• Read this manual carefully before
installing or operating your new air
conditioning unit. Make sure to save
this manual for future reference.
• This manual only describes the installation of
outdoor unit. When installing the indoor unit,
refer to the installation manual of indoor unit.
8
8
INDOOR UNIT
1
2
3
4
5
6
Never use a flammable spray such as hair spray, lacquer
or paint near the unit.
It may cause a fire.
Do not place items which might be damaged by moisture
under the indoor unit.
Condensation may form if the humidity is above 80%, the
drain outlet is blocked or the filter is polluted.
Never touch the air outlet or the horizontal blades while
the swing flap is in operation.
Fingers may become caught or the unit may break down.
After a long use, check the unit stand and fitting for
damage.
If damaged, the unit may fall and result in injury.
Never put any objects into the air inlet or outlet.
Objects touching the fan at high speed can be dangerous.
To avoid oxygen deficiency, ventilate the room
sufficiently if equipment with burner is used together
with the air conditioner.
Ask your dealer for improvement, repair, and
maintenance.
Incomplete improvement, repair, and maintenance may result
in a water leakage, electric shock, and fire.
Fig.1
OUTDOOR UNIT
7
8
9
Air flow louver (at air outlet)
Air inlet (with air filter in it)
Installation part
Connecting pipe
In order to avoid electric shock, fire or injury, or if you
detect any abnormality such as smell of fire, turn off the
power supply and call your dealer for instructions.
Air inlet
Air outlet
Never let the indoor unit or the remote controller get wet.
It may cause an electric shock or a fire.
Display panel
Remote controller
Never press the button of the remote controller with a
hard, pointed object.
The remote controller may be damaged.
Drain pipe
Never replace a fuse with that of wrong rated current or
other wires when a fuse blows out.
Use of wire or copper wire may cause the unit to break down
or cause a fire.
NOTE
All the pictures in this manual are for explanation purpose only. They may be slightly different from the air
conditioner you purchased(depend on model). The actual shape shall prevail.
Turn off any combustible heating devices, ventilate the
room, and contact the dealer where you purchased the
unit.
Do not use the air conditioner until a service person confirms
that the portion where the refrigerant leaks is repaired.
CAUTION
Symptom 2: Change into the fan mode during
cooling mode
Never use a damp cloth on the remote controller.
In order to prevent the indoor evaporator frosting, the system
will change into fan mode automatically, restore to the cooling
mode after soon.
The air-in side should face up when using vacuum cleaner.
Do not use a chemically-treted duster for wiping or leave
such material on the unit for long.
it may damage or fade the surface of the unit.
The air-in side should face down when using water.
Do not dry out the air filter under direct sunshine or with fire.
Maintenance after a long stop period
Before cleaning, be sure to stop the operation, turn the
breaker off or pull out the supply cord.
Otherwise, an electric shock and injury may result.
Open the air intake with the screwdriver or something like
that .(Refer to Fig.6-1)
Take out the air filter.(Refer to Fig.6-2)
Clean the air cleaning filter with water or vacuum cleaer,then
dry it in cool place.
Re-install the air filter in the reverse order of Fig.6-2.
2
14-16KW
Directly pull out the air filter from air inlet as indicated in
Fig.6-3.
Clean the air cleaning filter with water or vacuum cleaner,
then dry it in cool place.
Re-install the air filter in the reverse order of Fig.6-3.
2
Communication malfunction
between indoor and outdoor units
E1
OFF
2
3
Indoor fan speed malfunction
E3
OFF
4
OFF
6
A "pishi-pishi" squeaking sound is heard when the system stops
after heating operation.
Expansion and contraction of plastic parts caused by
temperature change make this noise.
Symptom 4.2: Indoor unit, outdoor unit
A continuous low hissing sound is heard when the system is in
operation.
This is the sound of refrigerant gas flowing through both indoor
and outdoor units.
A hissing sound which is heard at the start or immediately after
stopping operation or defrost operation.
This is the noise of refrigerant caused by flow stop or flow
change.
Fig.6-3
If the air conditioner is installed in a dust place, clean the
the air filter frequent.
3.2-10.5KW
1
E5
Clean air filters and casings of indoor units. Refer to "
Cleaning the air filter" for details on how to proceed and
make sure to install cleaned air filters back in the same
position.
1
OFF
Evaporator coil temperature
sensor open circuit or short circuit
A continuous low "shah" sound is heard when the system is in
cooling operation or at a stop.
When the drain pump (optional accessories) is in operation,this
noise is heard.
Symptom 4.3: Outdoor unit
When the tone of operating noise changes.
This noise is caused by the change of frequency.
FOLLOWING SYMPTOMS ARE NOT AIR
CONDITIONER TROUBLES
E0
5
Fig.6-2
7.
Indoor EEPROM error
A safety device such as a fuse, a breaker frequently actuates.
(eg. at the end of the season)
The filter cleaning should be performed by a suitable
service provider.
1
Obstacles and water enter the unit.
Water leaks from indoor unit.
Other malfunctions.
If the system does not properly operate except the above
mentioned cases or the above mentioned malfunctions is
evident, investigate the system according to the following
procedures. (See in Table 8-2)
8.2
Troubles and causes of remote controller
Before asking for serving or repairing, check the following
points.(See in Table 8-3)
6
Refrigerant leakage detection
malfunction
EC
OFF
7
7
Water-level alarm malfunction
EE
OFF
8
8
Communication malfunction
between two indoor units (for
twins model)
E8
OFF
9
9
Other malfunction of twins model
E9
OFF
10
10
Current overload protection
F0
ON
1
11
Outdoor room temperature sensor
open circuit or short circuit
F1
ON
2
12
Outdoor condenser pipe
temperature sensor error
F2
ON
3
13
Discharging air temperature
sensor error
F3
ON
14
Outdoor EEPROM error
F4
ON
5
15
Outdoor fan speed malfunction
(Only for DC fan motor)
F5
ON
6
16
T2b sensor error
F6
ON
7
17
Inverter module IPM protection
P0
Flash
1
18
High/Low voltage protection
P1
Flash
2
19
High temperature protection of
compressor top
P2
Flash
3
20
Outdoor low temp. protection
P3
Flash
4
21
Compressor drive error
P4
Flash
5
22
Mode conflict
P5
Flash
6
Unit does not start
Air flowing normally but
completely can't cooling
Units start or stop frequently
Low cooling effect
4
Low heating effect
Be sure the air conditioner is grounded.
In order to avoid electric shock, make sure that the unit is
grounded and that the earth wire is not connected to gas or
water pipe, lightning conductor or telephone earth wire.
If the operation lamp and the "PRE-DEF indicator(cooling and
heating type) or fan only indicator(cooling only type)" light, it
means you choose the heating model, When just starting, if the
compressor has not started, the indoor unit appears "anti cold
wind" protection because of its overlow outlet temperature.
owner’s manual
5
The unit can absorb the smell of rooms, furniture, cigarettes,
etc., and then emit it again.
Symptom 7: The outdoor unit fan does not
spin.
During operation. The speed of the fan is controlled in order to
optimize product operation.
6
DEF./FAN
Fig. 2-5
NOTE:DEF indicator(cooling and heating type)
or FAN indicator(cooling only type)
owner’s manual
7
owner’s manual
8
Lighting or a car wireless telephone operating nearby
may cause the unit to malfunction.
Disconnect the unit with the power and then connect the unit
with the power again. Push the ON/OFF button on the remote
controller to restart operation.
ALARM
,
Infrared signal receiver
NOTE:DEF indicator(cooling and heating type)
or FAN indicator(cooling only type)
Display panel
Fig. 2-1
DEF./FAN
Display panel
For some models, the machine is special designed with louver
angle memory function.Power failure during operation or
pressing the ON/OFF button on the remote controller will stop
the unit completely.When the power restores or pressing the
ON/OFF button on the remote controller again,the unit restarts
automatically with the previous open angle of the horizontal
louver by the memory function.So we strongly recommend that
the open angle of the horizontal louver should not be set too
small,in case the condensed water forms and drops from the
horizontal louver. Press the Manual control button and the open
angle of the horizontal louver will be restored to the standard
angle.
Fig. 2-6
Operation lamp
Infrared signal receiver
Timer indicator
ALARM
PRE-DEF indicator(cooling and heating
type)
or fan only indicator(cooling only type)
Infrared signal receiver
Temporary button
PRE-DEF indicator(cooling and heating
type)
or fan only indicator(cooling only type)
MANUAL
Operation lamp
Alarm indicator
Temporary button
Temperature indecator
Display panel
Timer indicator
Display panel
Fig. 2-2
Operation lamp
AIR CONDITIONER OPERATIONS AND
PERFORMANCE
4.
Outdoor
temperature
Mode
Temporary button
Cooling operation
0°C ~ 50°C / 32 °F~122°F
-15°C ~ 50°C / 5 °F~122°F
(for the models with low
temperature cooling system)
Heating operation
(cooling only type without)
-15°C ~ 24°C / 5 °F~76°F
Drying operation
0°C ~ 50°C / 32 °F~122°F
Room
temperature
Timer indicator
Alarm indicator
Display panel
Infrared signal receiver
Fig. 2-3
Timer indicator
Temperature indecator
Alarm indicator
Display panel
Fig. 2-8
For inverter type,this switch is used for after-sales service
purpose only,the user should not push it.
2
3
5.2
Auto-swing
Press SWING H button, the louver will swing left and right
automatically.
In cooling, close the curtains to avoid direct sunlight.
17°C ~ 32°C
( 62 °F ~ 90°F)
0°C ~ 30°C / 32 °F~86°F
Set the timer for the desired operating time.
17°C ~ 32°C
( 62 °F ~ 90°F)
Never put obstructions near the air outlet or the air inlet. Or it
will cause lower efficiency, even a sudden stop.
owner’s manual
3
2
Fig. 5-4
To keep cool or warm air in the room, never open doors or
windows more often than necessary.
If you don't plan to use the unit for a long time, please disconnect power and remove the batteries from the remote controller. When the power switch is connected, some energy will be
consumed, even if the air conditioner isn't in operation. So
please disconnect the power to save energy. And please
switch the power on 12 hours before you restart the unit to
ensure a smooth operation.
If air conditioner is used outside the above conditions, it may
cause the unit to function abnormally.
The phenomenon is normal that the surface of air
conditioning may condense water when the relative larger
humidity in room, please close the door and window.
Optimum performance will be achieved within these
operating temperature range.
owner’s manual
Adjust the Vertical louver
Adjust the room temperature properly to get a comfortable
situation and to avoid supercooling and superheat.
NOTE
1
HINTS FOR ECONOMICAL OPERATION
Adjust the air flow direction properly to avoid winding toward
your body.
Temperature
Fig. 2-7
Operation lamp
When heating
Adjust the louver downwards. (vertically)
The following should be noticed to ensure an economical operation.
(Refer to corresponding chapterfor details)
Table 3-1
PRE-DEF indicator(cooling and heating
type)
or fan only indicator(cooling only type)
Infrared signal receiver
PRE-DEF indicator(cooling and heating
type)
or fan only indicator(cooling only type)
3.
Temperature indecator
Alarm indicator
Fig. 5-2
Fig. 5-3
Use the system in the following temperature for safe and
effective operation. The Max operation temperature for
the air conditioner.(Cooling/Heating)
MANUAL
When cooling
Adjust the louver horizontally.
,
Louver Angle Memory Function(optional):
MANUAL
OPERATION TIMER
Fig. 5-1
Refrigerant Leakage Detection(optional):
This manual does not include Remote Controller
Operations, see the<<Remote Controller Owner's
manual>> packed with the unit for details.
Infrared signal receiver
Adjust the horizontal louver
Manual Swing
Adjust the louver to achieve better cooling/heating effects
when cooling /heating.
With this new technology, the dipsplay area will appear EC (if
applicable) and the LED indication lamps continue flashing
when the outdoor unit detects refrigerant leakage.
Causes
Solution
Power failure.
Power switch is off.
Fuse of power switch may have burned.
Batteries of remote controller exhausted
or other problem of controller.
Wait for the comeback of power.
Switch on the power.
Replace the fuse.
Replace the batterises or check the
controller.
Temperature is not set correctly.
Be in 3 minutes protection
compressor.
Set the temperature properly.
Wait.
of
Refrigerant is too little or too much.
Air or no concretingc gas in the
refrigerating circuit.
Compressor is malfunction.
Voltage is too high or too low.
System circuit is blocked.
Check leakage, and rightly recharge
refrigerant.
Vacuum and recharge refrigerant.
Maintenance or change compressor.
Install manostat.
Find reasons and solution.
Outdoor unit and indoor unit heat
exchanger is dirty.
The air filter is dirty.
Inlet/outlet of indoor/outdoor units is
blocked.
Doors and windows are open
Sunlight directly shine.
Too much heat resource.
Outdoor temp. is too high.
Leakage of refrigerant or lack of
refrigerant.
Clean the heat exchanger.
Clean the air filter.
Eliminate all dirties and make air
smooth.
Close doors and windows.
Make curtains in order to shelter from
sunshine.
Reduce heat source.
AC cooling capacity reduces (normal).
Check leakage and rightly recharge
refrigerant.
Outdoor temperature is lower than 7 C
Doors and windows not completely
closed.
Leakage of refrigerant or
lack of
refrigerant.
Use heating device.
Close doors and windows.
Check leakage and rightly recharge
refrigerant.
Symptoms
The fan speed can not be
changed.
Causes
A clogged air filter will reduce cooling or heating efficiency,
please clean it once two weeks.
6.
MAINTENANCE
CAUTION
Before you clean the air conditioner, be sure the power
supply is off.
Check if the wiring is not broken off or disconnected.
Use a dry cloth to wipe the indoor unit and remote
controller.
owner’s manual
4
Check whether the MODE
indicated on the display is
"AUTO"
When the automatic mode is
selected, the air conditioner will
automatically change the fan
speed.
Check whether the MODE
indicated on the display is
"DRY"
When dry operation is selected,
the air conditioner automatically
change the fan speed. The fan
speed can be selected during
"COOL" , "FAN ONLY", and "HEAT".
Check whether the batteries
in the remote controller are
exhausted.
The TEMP. indicator does
not come on.
Check whether the MODE
indicated on the display is
FAN ONLY
The temperature cannot be set during
FAN mode.
Check whether the timer
operation has come to an
end when the TIMER OFF
is indicated on the display.
The air conditioner operation will
stop up to the set time.
Check whether the timer
operation is started when
the TIMER ON is indicated
on the display.
Up to the set time, the air conditioner
will automatically start and the
appropriate indicator will go off.
The TIMER ON indicator
goes off after a lapse of
certain time.
www.cooperandhunter.us
THIS WARRANTY DOES NOT COVER:
LIMITED WARRANTY STATEMENT
MULTI ZONE INVERTER AIR CONDITIONING SYSTEM WITH HEAT PUMP
The remote controller signal is
not transmitted even when
the ON/OFF button is pushed.
The indication on the display
disappears after a lapse of
time.
LIMITATIONS OF WARRANTIES: ALL IMPLIED WARRANTIES AND/OR CONDITIONS (INCLUDING IMPLIED WARRANTIES OR
CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR USE OR PURPOSE) ARE LIMITED TO THE DURATION OF
THIS LIMITED WARRANTY. SOME STATES OR PROVINCES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY
OR CONDITION LASTS, SO THE ABOVE MAY NOT APPLY TO YOU. THE EXPRESS WARRANTIES MADE IN THIS WARRANTY ARE
EXCLUSIVE AND MAY NOT BE ALTERED, ENLARGED, OR CHANGED BY ANY DISTRIBUTOR, DEALER, OR OTHER PERSON,
WHATSOEVER.
Solution
The power supply is off.
This warranty should be registered on our web-site www.cooperandhunter.us
The warranty is only valid when installed by a Licensed HVAC Technician
FOR WARRANTY SERVICE OR REPAIR:
Contact your installing contractor. You may find the installer’s name on the equipment or in your Owner’s packet.
Complete product registration below and send back by e-mail at warranty@cooperandhunter.us
PRODUCT REGISTRATION:
Model No.: ______________________________________________________________________________________________
Serial No.: _______________________________________________________ Date of Installation: ______________________
Owner Name: ____________________________________________________________________________________________
No receiving tone sounds
from the indoor unit even
when the ON/OFF button is
pressed.
Check whether the signal
transmitter of the remote
controller is properly directed
to the infrared signal receiver
of the indoor unit when the
ON/OFF button is pressed.
Directly transmit the signal transmitter
of the remote controller to the infrared
signal receiver of the indoor unit, and
then repeatly push the ON/OFF button
twice.
Address of Installation:_____________________________________________________________________________________
Installing Contractor: ______________________________________________________________________________________
Address: ________________________________________________________________________________________
Phone No. / E-mail: _______________________________________________________________________________
C&H distributor (hereinafter “Company”) warrants this product against failure due to defect in materials or workmanship
under normal use and maintenance as follows. All warranty periods begin on the date of original installation. If the date cannot
be verified, the warranty period begins one hundred twenty (120) days from date of manufacture. Damage resulting from
failure to use, install or maintain the product in a manner consistent with our/manufacturer’s recommendations shall render the
warranty void. Cooper&Hunter, at its option, may request a report from a qualified technician prior to honoring a warranty
claim. If a part fails due to defect during the applicable warranty period Company will provide a new or remanufactured part, at
Company’s option, to replace the failed defective part at no charge for the part. This limited warranty is subject to all
provisions, conditions, limitations and exclusions listed below.
● A warranty period of Seven (7) years on compressor to the original registered end-user.
● A warranty period of Five (5) years on all parts to the original registered end user.
● A warranty period of One (1) year on the remote control provided with the original unit.
● Limited warranty applies only to systems that are properly installed by a state certified or licensed HVAC contractor,
under applicable local and state law in accordance with all applicable building codes and permits; C&H installation
and operation instructions and good trade practices.
● Warranty applies only to products remaining in their original installation location.
● Defective parts must be returned to the distributor through a registered servicing dealer for credit.
Symptom 6: The units can give off odours
owner’s manual
Display panel
TIMER
OPERATION
ADJUSTING AIR FLOW DIRECTION
Auto-swing
Press SWING V button, the louver will swing up and down
automatically.
To restart operation, push the ON/OFF button on the
remote controller.
ALARM
Date of Purchase: _______________________________________________________________________________
When the unit is used for the first time in a long time.
This is because dust has gotten into the unit.
The air conditioner does not start immediately after the ON/OFF
button on the romote controller is pressed.
If the operation lamp lights, the system is in normal condition.To
prevent overloading of the compressor motor, the air
conditioner starts 3 minutes after it is turned ON.
DEF./FAN
5.1
The OPERATION lamp on the indoor unit will start
flashing when power is restored.
OFF
The OPERATION lamp goes off. The air conditioner is OFF
while the remote controller operation is enabled.
MANUAL
5.
Power failure during operation will stop the unit completely.
NOTE
MANUAL
Children should be supervised to ensure that they do not
play with the appliance.
In order to avoid injury, do not remove the fan guard of
the outdoor unit.
3
OPERATION TIMER
Power failure
FORCED COOL
The OPERATION lamp flashes, the air conditioner will turn to
FORCED AUTO after it is enforced to cool with a wind speed of
HIGH for 30 minutes. The remote controller operation is
disabled.
Place Of Purchase: ________________________________________________________________________________________
Symptom 5: Dust comes out of the unit
Symptom 1: The system does not operate
Function indicators on indoor unit display panel
2
Infrared signal receiver
The air conditioner consists of the indoor unit, the outdoor unit,
the connecting pipe and the remote controller. (See Fig.1)
A protection feature prevents the air conditioner from being
activated for approximately 3 minutes when it restarts immediately after operation.
1 FORCED AUTO
The OPERATION lamp is lit, and the air conditioner will run
under FORCED AUTO mode. The remote controller operation is
enabled to operate according to the received signal.
Fig. 2-4
NOTE:DEF indicator(cooling and heating type)
or FAN indicator(cooling only type)
Three-minute protection feature
For fixed-frequency type,this function is used to operate the unit
temporarily in case you misplace the remote controller or its
batteries are exhausted. Two modes including FORCED
AUTO and FORCED COOL can be selected through the
TEMPORARY BUTTON on the air-in grill control box of the
indoor unit. Once you push this button, the air conditioner will
run in such order: FORCED AUTO, FORCED COOL, OFF,
and back to FORCED AUTO.
Table 8-3
Symptoms
running lamp (flashes per second)
Symptom 3.1: Indoor unit
Symptom 4.1: Indoor unit
If the accumulated dust is too heavy to be cleaned, please
replace the filter with a new one(replaceable air filter is an
optional fitting).
timer lamp
5
Sptom 4: Noise of air conditionerscooling
Cleaning the air filter
display (nixie tube)
OFF
Symptom 3.2: Indoor unit, outdoor unit
Maintenance before a long stop period
Malfunction
E4
When humidity is high during cooling operation If the interior of
an indoor unit is extremely contaminated, the temperature
distribution inside a room becomes uneven. It is necessary to
clean the interior of the indoor unit. Ask your dealer for details
on cleaning the unit. This operation requires a qualified service
erson
Air filter
The air filter can prevent the dust or other particulate from
going inside. In case of blockage of the filter, the working
efficiency of the air conditioner may greatly decrease.
Therefore, the filter must be cleaned once two weeks
during long time usage.
The operation lamp is flashing rapidly (5Hz) This lamp is still
flashing rapidly after turn off the power and turn on again.
(See in Table 8-1)
NO.
Indoor room temperature sensor
open circuit or short circuit
When the system is changed over to heating operation after
defrost operation Moisture generated by defrost becomes
steam and is exhausted.
Let the indoor units run in fan only operation for about half
a day in order to dry the interior of the units.
If one of the following malfunctions occur, stop operation, shut
off the power, and contact with your dealer.
TEMPORARY OPERATIONS
This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities,or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
In order to avoid electric shock or fire, make sure that an
earth leak detector is installed.
Table 8-2
4
Check and remove everything that might be blocking inlet
and outlet vents of indoor units and outdoor units.
Turn on the power at least 12 hours before operating the
unit in order to ensure smoother operation. As soon as he
power is turned on, the remote controller displays appear.
Troubles and causes of air conditioner
Table 8-1
Remote controller receives malfunction or the button does not
work well.
Air Inlet
Fig.6-1
TROUBLESHOOTING
Symptom 3: White mist comes out of a unit
(eg. at the beginning of the season)
Clean air filters and casings of indoor units.
Refer to "Cleaning the air filter" for details on how to
proceed and make sure to install cleaned air filters back in
the same position.
8.1
When the room temperature drops to the set temperature, the
compressor goes off and the indoor unit changes to fan mode;
when the temperature rises up, the compressor starts again. It
is same in the heating mode.
CAUTION
Do not use benzine, thinner, polishing powder, or similar
solvents for cleaning.
These may cause the plastic surface to crack or deform.
8.
2.
This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe way
and understand the hazards involved. Children shall not
play with the appliance.Cleaning and user maintenance
shall not be made by children without supervision.
Do not use the air conditioner for other purposes.
In order to avoid any quality deterioration, do not use the unit
for cooling precision instruments, food, plants, animals or
works of art.
ALARM
Display panel
Do not install the air conditioner at any place where
flammable gas may leak out.
If the gas leaks out and stays around the air conditioner, a
fire may break out.
The appliance is not intended for use by young children
or infirm persons without supervision.
1
NOTE
Do not place appliances which produce open fire in
places exposed to the air flow from the unit or under the
indoor unit.
It may cause incomplete combustion or deformation of the
unit due to the heat.
DEF./FAN
NOTE:DEF indicator(cooling and heating type)
or FAN indicator(cooling only type)
Do not operate the air conditioner when using a room
fumigation - type insecticide.
Failure to observe could cause the chemicals to become
deposited in the unit, which could endanger the health of
those who are hypersensitive to chemicals.
The refrigerant in the air conditioner is safe and normally
does not leak.
If the refrigerant leaks in the room, contact with a fire of a
burner, a heater or a cooker may result in a harmful gas.
TIMER
Infrared signal receiver
Do not allow a child to mount on the outdoor unit or
avoid placing any object on it.
Falling or tumbling may result in injury.
To prevent refrigerant leak, contact your dealer.
When the system is installed and runs in a small room, it is
required to keep the concentration of the refrigerant, if by any
chance coming out, below the limit. Otherwise, oxygen in the
room may be affected, resulting in a serious accident.
OPERATION
Temperature indecator
Never expose little children, plants or animals directly to
the air flow.
Adverse influence to little children, animals and plants may
result.
If electrical appliances are disposed of in landfills or
dumps, hazardous substances can leak into the
groundeater and get into the food chain, damaging your
health and well-being.
MANUAL
Do not operate your air conditioner in a wet room such
as a bathroom or laundry room.
Never touch the internal parts of the controller.
Do not remove the front panel. Some parts inside are
dangerous to touch, and a machine trouble may happen.
Do not dispose of electrical appliances as unsorted
municipal waste, use separate collection facilities.
Contact you local government for information regarding the
connection systems available.
owner’s manual
A wet cloth may be used to clean the indoor unit if it is
very dirty.
Arrange the drain hose to ensure smooth drainage.
Incomplete drainage may cause wetting of the building,
furniture etc.
Do not dispose this product as unsorted municipal
waste. Collection of such waste separately for special
treatment is necessary.
IMPORTANT SAFETY INFORMATION
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
Do not touch the heat exchanger fins.
These fins are sharp and could result in cutting injuries.
Never inspect or service the unit by yourself.
Ask a qualified service person to perform this work.
DUCTLESS INVERTER
INDOOR UNIT
Do not insert fingers, rods or other objects into the air
inlet or outlet.
When the fan is rotating at high speed, it will cause injury.
E ON
8
OUTDOOR UNIT
Do not operate the air conditioner with a wet hand.
An electric shock may happen.
E OFF
5
SPLIT AIR CONDITIONER
WITH HEAT PUMP
UNIVERSAL FLOOR/CEILING
It is not good for your health to expose your body to the
air flow for a long time.
1.
Labor or other costs incurred for diagnosing, repairing, removing, installing, shipping, servicing, or handling of defective
parts, replacement parts, or new units.
2.
3.
Product cleaning required prior to warranty service and repair.
Normal maintenance as outlined in the installation and servicing instructions or user's manual, including filter
cleaning and/or replacement and lubrication.
Failure, damage, or repairs due to faulty installation, misapplication, abuse, improper servicing, unauthorized
alteration, or improper operation.
Failure to start due to voltage conditions, blown fuses, open circuit breakers, or damages due to the inadequacy or
interruption of electrical service.
Failure or damage due to floods, winds, fires, lightning, accidents, corrosive environments (rust, etc.), or other
conditions beyond the control of Company.
Failure or damage of coils or piping due to corrosion on installations within one (1) mile of a sea coast or a corrosive
body.
Parts not supplied or designated by Company, or damages resulting from their use.
Products installed outside the continental USA and Canada.
Electricity or fuel costs, or increases in electricity or fuel costs for any reason whatsoever, including additional or
unusual use of supplemental electric heat.
Any cost to replace, refill, or dispose of refrigerant, including the cost of refrigerant.
Shipping damage or damage as a result of transporting the unit.
Accessories such as condensate pumps, line sets, and so forth.
Any special, indirect, or consequential property or commercial damage of any nature whatsoever. Some states or
provinces do not allow the exclusion of incidental or consequential damages, so the above limitation may not apply to
you.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to
province.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising