Frigidaire | FGRC1044T1 | Manual and User Guide | Frigidaire FGRC1044T1 Manual and User Guide

All about the
Use & Care
of your
Smart Room Air Conditioner
TA B L E O F C O N T E N T S
Important Safety Instructions ............................... 2-3
Operating Instructions ......................................... 6-10
FCC Statement ..................................................... 4
Product Registration ............................................. 5
Care and Cleaning .............................................. 11
Packaging ........................................................... 5
Normal Sounds .................................................... 5
Air Conditioner Features ....................................... 6
Before You Call ................................................... 12
Major Appliance Limited Warranty ........................ 13
www.frigidaire.ca Canada 1-800-265-8352
16120300A11043 (June 2009)
www.frigidaire.com USA 1-800-944-9044
Energy Saving Ideas ........................................... 11
Important Safety Instructions
NOTE:
This USE & CARE MANUAL provides specific operating instructions for your model. Use the room air conditioner only as
instructed in this USE & CARE MANUAL. These instructions are not meant to cover every possible condition and situation that
may occur. Common sense and caution must be practiced when installing, operating, and maintaining any appliance.
NOTE:
WARNING
The power supply cord with
this air conditioner contains a current
detection device designed to reduce the risk
of fire.
Please refer to the section ‘Operation of
Current Device’ for details.
In the event that the power supply cord is
damaged, it cannot be repaired. It must be
replaced with a cord from the product
manufacturer.
WARNING
Avoid fire hazard or electric shock. Do not
use an extension cord or an adaptor plug. Do
not remove any prong from the power cord.
Grounding type wall
receptacle
For Your Safety
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any
other appliance. Read product labels for flammability and other warnings.
WARNING
Prevent Accidents
To reduce the risk of fire, electrical shock, or injury to persons when using your air conditioner,
follow basic precautions, including the following:
Be sure the electrical service is adequate for the model you have chosen. This information
can be found on the serial plate, which is located on the side of the cabinet and behind the
grille.
If the air conditioner is to be installed in a window, you will probably want to clean both
sides of the glass first. If the window is a triple-track type with a screen panel included,
remove the screen completely before installation.
Be sure the air conditioner has been securely and correctly installed according to the
separate installation instructions provided with this manual. Save this manual and the
installation instructions for possible future use in removing or reinstalling this unit.
When handling the air conditioner, be careful to avoid cuts from sharp metal fins on front
and rear coils.
Do not, under any
circumstances, cut,
remove, or bypass the
grounding prong.
WARNING
Electrical Information
The complete electrical rating of your new room air conditioner is stated on the serial plate.
Refer to the rating when checking the electrical requirements.
Be sure the air conditioner is properly grounded. To minimize shock and fire hazards,
proper grounding is important. The power cord is equipped with a three-prong grounding
plug for protection against shock hazards.
Your air conditioner must be used in a properly grounded wall receptacle. If the wall
receptacle you intend to use is not adequately grounded or protected by a time delay fuse
or circuit breaker, have a qualified electrician install the proper receptacle.
Power supply cord
with 3-prong grounding
plug and current
detection device
Do not run air conditioner without outside protective cover in place. This could result in
mechanical damage within the air conditioner.
Do not use an extension cord or an adapter plug.
SAFETY PRECAUTIONS
DANGER! Avoid Serious Injury or Death
This air conditioner contains no user-serviceable parts. Always call an authorized Electrolux servicer for repairs.
Do not insert or place fingers or objects into the air discharge area in the front of the unit.
Do not start or stop the air conditioner by unplugging the power cord or turning off the power at the electrical box.
Do not cut or damage the power cord.
If the power cord is damaged, it should only be replaced by an authorized Electrolux servicer.
In the event of a malfunction (sparks, burning smell, etc.), immediately stop the operation, disconnect the power cord, and call an authorized
Electrolux servicer.
Do not operate the air conditioner with wet hands.
Do not pull on the power cord.
Do not drink any water that is drained from the air conditioner.
2
2009 Electrolux Home Products, Inc.
All rights reserved.
Important Safety Instructions
SAFETY PRECAUTIONS
CAUTION! Avoid Injury or damage to the unit or other property
Provide occasional ventilation during use. Do not direct airflow at fireplaces or other heat related sources as this could cause flare ups or make
units run excessively.
Do not climb on or place objects on outdoor part of the unit.
Do not hang objects off the unit.
Do not place containers with liquids on the unit.
Turn off the air conditioner at the power source when it will not be used for an extended period of time.
Periodically check the condition of the unit’s installation accessories for any damage.
Do not apply heavy pressure to the radiator fins of the unit.
Operate the unit with air filter in place.
Do not block or cover the intake grille, discharge area and outlet ports.
Ensure that any electrical/electronic equipment is one yard away from the unit.
Do not use or store flammable gases near the unit.
Do not touch the metal parts of the unit when removing the filter. Injuries can occur when handling sharp metal edges.
Do not use water to clean inside the air conditioner. Exposure to water can destroy the insulation, leading to possible electric shock.
When cleaning the unit, first make sure that the power and circuit breaker are turned off.
READ THIS SECTION BEFORE ATTEMPTING TO OPERATE AIR CONDITIONER.
Unit must be upright for one hour prior to operating.
The power supply cord contains a current device that senses damage to the power cord. To test
your power supply cord do the following:
Plug in &
press RESET
Plug in the Air Conditioner.
The power supply cord will have TWO buttons on the plug head. Press the TEST button. You will
notice a click as the RESET button pops out.
Press the RESET button. Again you will notice a click as the button engages.
The power supply cord is now supplying electricity to the unit. (This is also indicated by a light
on the plug head).
NOTE:
Do not use this device to turn the unit on or off.
Always make sure the RESET button is pushed in for correct operation.
The power supply cord must be replaced if it fails to reset when either the TEST button is pushed,
or it cannot be reset. A new one can be obtained from the product manufacturer.
If power supply cord is damaged, it CANNOT be repaired. It MUST be replaced by one obtained
from the product manufacturer.
2009 Electrolux Home Products, Inc.
All rights reserved.
3
FCC Statement
FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by tuning the device off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the device and receiver.
Connect the equipment into an outlet other than the one used for the receiver.
Consult the dealer or an experienced radio/TV technician for assistance.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) This device must accept any interference received, including interference that may cause
undesired operation.
FCC CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
Host device Labeling
This device includes the following module.
Contains FCC ID: 2ABHC-5430042
RF exposure statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be
installed and operated with minimum 20 cm between the radiator and your body. This transmitter must not be collocated or
operating in conjunction with any other antenna or transmitter unless authorized to do so by the FCC.
INDUSTRY CANADA (IC) STATEMENT
This Class B digital apparatus complies with Canadian ICES-003.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
RF Exposure
The antenna (or antennas) must be installed so as to maintain at all times a distance minimum of at least 20 cm between the
radiation source (antenna) and any individual. This device may not be installed or used in conjunction with any other antenna
or transmitter.
l'exposition aux RF
L’antenne (ou les antennes) doit être installé e de façon à maintenir à tout instant une distance minimum de au moins 20 cm entre la
source de radiation (l’antenne) et toute personne physique.
Host device Labeling
This device includes the following module.
Contains IC: 12012A-5430042
Host dispositif d'étiquetage
Ce dispositif inclut le module suivant.
Contient module émetteur IC: 12012A-5430042
This is the location
of the module.
4
2009 Electrolux Home Products, Inc.
All rights reserved.
Product Registration, Packaging & Normal Sounds
Product Registration
Record Your Model and Serial Numbers
Record in the space provided below the model and serial numbers. On all models, the
serial plate is located on the outside of the cabinet.
Model No.
Serial No.
Register Your Product
The self-addressed PRODUCT REGISTRATION CARD should be filled in completely,
signed and returned to the Frigidaire Company.
Packaging
Remove all packaging from inside the carton, along with any
inserts placed into the side louvers.
PACKAGING INSERTS
Normal Sounds
High pitched Chatter
Today’s high efficiency compressors
may have a high pitched chatter
during the cooling cycle.
Sound of Rushing Air
Vibration
Unit may vibrate and make noise
because of poor wall or window
construction or incorrect installation.
At the front of the unit, you may
hear the sound of rushing air
being moved by the fan.
Pinging or Swishing
Gurgle/Hiss
“Gurgling or hissing” noise may be
heard due to refrigerant passing
through evaporator during normal
operation.
2009 Electrolux Home Products, Inc.
Droplets of water hitting condenser
during normal operation may cause
“pinging or swishing” sounds.
Note: Don’t try to drill any holes
on the base pan to eliminate the
normal sounds, otherwise it will
void the warranty.
All rights reserved.
5
Air Conditioner Features & Operating Instructions
Air Conditioner Features
TURNS UNIT
ON OR OFF
ELECTRONIC CONTROL
Before you begin, thoroughly familiarize yourself with the control panel and remote
control and all its functions (as shown below). The unit can be controlled by the
touch pad alone, with the remote control, or with the Frigidaire app*.
ADJUSTS
SCHEDULE
TEMPERATURE
INDICATOR
WIFI
DISPLAYS
SETS FAN
CHECK FILTER
TEMPERATURE
SPEED
RESET BUTTON
*Refer to the Quick Start Guide that came with your Smart Air Conditioner for detailed instructions on setting up your air
conditioner for connected operation from your smart phone or tablet.
Note: The display and indicator lights will turn off if the unit does not receive any control signal in 60 second.
Press any button then the display will resume.
SET MODE
TO REPLACE BATTERY
TAB
Battery Size: CR2025
REMOTE CONTROL
Turn Remote Control upside down. Squeeze tab and
pull to remove battery tray. Place battery in tray with
POSITIVE(“+”) side facing UP, according to diagram.
Re-insert battery tray.
Operating Instructions
NOTE
The following instructions represent the touch pad. The same instructions can be used for the remote control.
TO TURN UNIT ON:
DO THIS:
PRESS ON/OFF BUTTON
6
2009 Electrolux Home Products, Inc.
YOU WILL SEE:
Note: The unit will run in eco (energy saver) mode when
used for the first time. We recommend leaving the unit in
eco mode to help save energy and money. For more
information please see section on 'Eco Mode'.
All rights reserved.
Operating Instructions
Operating Instructions
(continued)
TO CHANGE TEMPERATURE SETTlNG:
Note: The display will show the actual room temperature
during normal operation, press either up (+) or down (-)
button once to show the set temperature, press either the
button again to adjust the set temperature to the desired
setting. The unit will beep twice if the temperature up (+)
or down (-) button is pressed continuously when the set
temperature reaches the upper/lower limits 90°F or 60°F.
DO THIS:
PRESS
TO RAISE
PRESS
TO LOWER
YOU WILL SEE:
TO ADJUST FAN SPEEDS:
YOU WILL SEE:
DO THIS:
PRESS TO SELECT
TO USE AUTO FAN FEATURE:
DO THIS:
PRESS FAN BUTTON,
CHOOSE AUTO
2009 Electrolux Home Products, Inc.
YOU WILL SEE:
Note: Fan starts at High Speed and adjusts to a slower
speeds the room temperature dictates. For example, if the
room doesn't get too warm, it will stay at the slowest speed.
If the room temperature rises quickly, such as a door being
opened, it will automatically go to the highest speed. The fan
speeds will re-adjust back to the slowest speed as the room
returns to the original set temperature. Press either the fan
slower or fan faster button to adjust the fan speed manually.
All rights reserved.
7
Operating Instructions
Operating Instructions
(continued)
TO OPERATE ON FAN:
YOU WILL SEE:
DO THIS:
PRESS
MODE BUTTON
CHOOSE FAN
Note: Use this function only when cooling is not desired,
such as for room air circulation or to exhaust stale air on
some models. You can choose any fan speed you
prefer. (Except “Auto Fan”).
During this function, display will only show the actual
room temperature and the set temperature can not be
changed.
YOU WILL SEE:
COOL FEATURE:
DO THIS:
PRESS
MODE BUTTON
Note: In this mode, the fan remains on all the time with the
compressor cycling on and off when room temperature is
reached.
CHOOSE COOL
ECO (ENERGY SAVER) MODE:
The unit is factory set to run in eco (energy saver) mode.
We recommend leaving the unit in eco mode to help save
energy and money. However, if you would like to switch
out of eco mode, touch the button until another mode
is selected.
In eco mode, the fan will continue to run for 3 minute after
the compressor shuts off. The fan then cycles on for 90
seconds at 10 minute intervals until the room temperature
is above the set temperature, at which time the compressor
turns back on.
DO THIS:
PRESS
MODE BUTTON
CHOOSE COOL
NOTE:
Please note, that if the unit is changed to 'cool' or 'fan' mode then shut off, the unit will turn back on in eco mode. This is
mandatory per government regulations. If the unit is changed to 'cool' or 'fan' mode and a power failure occurs, once the
power is restored the unit will return to 'cool' or 'fan' mode.
8
2009 Electrolux Home Products, Inc.
All rights reserved.
Operating Instructions
Operating Instructions
(continued)
CHECK FILTER FEATURE, YOU WILL SEE:
Note: This feature is a reminder to clean the Air Filter (See
Care and Cleaning) for more efficient operation. The LED
(light) will illuminate after 250 hours of operation. To reset
after cleaning the filter, hold the " reset filter" button 3
seconds and the light will go off.
DO THIS:
HOLD RESET FILTER
BUTTON 3 SECONDS
FAULT CODES:
FAULT CODES:
If the display reads "AS" , a sensor has failed. Contact your
Authorized Frigidaire Service Center.
If the display reads "ES" , a sensor has failed. Contact your
Authorized Frigidaire Service Center.
DIMMING DISPLAY:
After 60 seconds of control inactivity the display and
indicator lights will turn off. Press any button on the
control panel or remote control and the display will
resume. Please note that if the unit is in eco mode
and the set temperature has been reached the unit
may appear off. However, the unit is on and will
continue to sample the air every 10 minutes. To
confirm, press any button on the control panel or
remote control to illuminate the display to show unit
in eco mode.
2009 Electrolux Home Products, Inc.
All rights reserved.
9
Operating Instructions
Operating Instructions
(continued)
TO CHANGE TEMPERATURE DISPLAY:
YOU WILL SEE:
Note: The control is capable of displaying temperature in
degrees Fahrenheit or degrees Celsius.
DO THIS:
PRESS AND HOLD THE
UP/DOWN BUTTONS
SIMULTANEOUSLY FOR 3 SECONDS
TO TURN UNIT OFF:
YOU WILL SEE:
Note: After the unit is turned off, the light on the display
will gradually fade away in 3 seconds. The unit will always
return to “eco” mode and “auto” fan speed setting when it
is turned on again.
DO THIS:
PRESS
ON/OFF BUTTON
ADDITIONAL THINGS YOU SHOULD KNOW
Now that you have mastered the operating procedure, here are more features in your control that you should become familiar with.
The "Cool" circuit has an automatic 3 minute time delayed start if the unit is turned off and on quickly.
This prevents overheating of the compressor and possible circuit breaker tripping. The fan will continue
to run during this time.
There is a 2-Second delay for the compressor shutting down when selecting FAN ONLY. This is to cover the possibility of having
to roll through to select another mode.
The control will maintain the set temperature within 2 degrees Fahrenheit, between 60F and 90F degrees.
After a power outage, the unit will memorize the last setting and return the unit to the same setting once power is restored.
Air Directional Louvers
Air directional louvers control air flow direction. Your air conditioner has the louver
type described below.
2-Way air directional louvers
(2-WAY)
10
The 2-Way air directional louvers allow you to direct the air flow Left or Right
throughout the room as needed. To adjust the air directional louvers side-to-side,
use the center handle as you move it side-to-side.
2009 Electrolux Home Products, Inc.
All rights reserved.
Care and Cleaning & Energy Saving Ideas
Care and Cleaning
Clean your air conditioner occasionally to keep it looking new. Be sure to unplug
the unit before cleaning to prevent shock or fire hazards.
Air Filter Cleaning
Air Filter
The air filter should be checked at least once a month to see if cleaning is
necessary. Trapped particles in the filter can build up and cause an accumulation
of frost on the cooling coils.
Pull out the alveolate grille from the front panel.
Grasp the filter(filter handle engraved with "filter" characters) by the center
and pull up and out.
Wash the filter using liquid dishwashing detergent and warm water. Rinse filter
thoroughly. Gently shake excess water from the filter. Be sure filter is
thoroughly dry before replacing
Or instead of washing, you may vacuum the filter clean.
Cabinet Cleaning
Be sure to unplug the air conditioner to prevent shock or fire hazard. The
cabinet and front may be dusted with an oil-free cloth or washed with a cloth
dampened in a solution of warm water and mild liquid dishwashing detergent.
Rinse thoroughly and wipe dry.
Never use harsh cleaners, wax or polish on the cabinet front.
Be sure to wring excess water from the cloth before wiping around the controls.
Excess water in or around the controls may cause damage to the air conditioner.
Plug in air conditioner.
Winter Storage
If you plan to store the air conditioner during the winter, remove it carefully from
the window according to the installation instructions. Cover it with plastic or return
it to the original carton.
Energy Saving Ideas
Do not block air flow inside with blinds, curtains or furniture; or outside with
shrubs, enclosures, or other buildings.
The capacity of the room air conditioner must fit the room size for efficient and
satisfactory operation.
Install the room air conditioner on the shady side of your home. A window that faces
north is best because it is shaded most of the day.
Close the fireplace damper, floor and wall registers so cool air does not escape up
the chimney and into the duct work.
Keep blinds and drapes in other windows closed during the sunniest part of the day.
Clean the air filter as recommended in the section “Care and Cleaning”.
Proper insulation and weather stripping in your home will help keep warm air out
and cool air in.
External house shading with trees, plants or awnings will help reduce the air
conditioner’s work load.
Operate heat producing appliances such as ranges, washers, dryers and dishwashers
during the coolest part of the day.
2009 Electrolux Home Products, Inc.
All rights reserved.
11
Before You Call
Before calling for service, review this list. It may save you time and expense. This list includes common occurrences that are not
the result of defective workmanship or materials in this appliance.
OCCURRENCE
SOLUTION
Air conditioner will not operate.
Wall plug disconnected. Push plug firmly into wall outlet.
Plug Current Device Tripped. Press the RESET button.
House fuse blown or circuit breaker tripped. Replace fuse with time delay type or reset circuit breaker.
Control is OFF. Turn Control ON and set to desired setting.
Air from unit does not feel cold
enough.
Room temperature below 60°F (16°C). Cooling may not occur until room temperature rises above
60°F (16°C).
Temperature sensing element touching cold coil, located behind air filter. Straighten away from coil.
Reset to a lower temperature.
Compressor shut-off by changing modes. Wait approximately 3 minutes and listen for compressor to
restart when set in the COOL mode.
Air conditioner cooling, but room
is too warm - ice forming
on cooling coil behind decorative
front
Outdoor temperature below 60 O F (16 O C). To defrost the coil, set FAN ONLY mode.
Air filter may be dirty. Clean filter. Refer to Care and Cleaning section. To defrost, set to FAN ONLY
mode.
Temperature is set too low for night-time cooling. To defrost the coil, set to FAN ONLY mode. Then,
set temperature to a higher setting.
Air conditioner cooling, but room
is too warm - NO ice forming on
cooling coil behind decorative
front.
Dirty air filter - air restricted. Clean air filter. Refer to Care and Cleaning section.
Temperature is set too high. Set temperature to a lower setting.
Air directional louvers positioned improperly. Position louvers for better air distribution.
Front of unit is blocked by drapes, blinds, furniture, etc. - restricts air distribution. Clear blockage in
front of unit.
Doors, windows, registers, etc. open - cool air escapes. Close doors, windows, registers, etc.
Unit recently turned on in hot room. Allow additional time to remove “stored heat” from walls, ceiling,
floor and furniture.
Air conditioner turns on and off
rapidly.
Noise when unit is cooling.
Dirty air filter - air restricted. Clean air filter.
Outside temperature extremely hot. Set FAN speed to a faster setting to bring air through cooling coils
more frequently.
Air movement sound. This is normal. If too loud, set to lower FAN setting.
Window vibration - poor installation. Refer to installation instructions or check with installer.
Water dripping INSIDE when
unit is cooling.
Improper installation. Tilt air conditioner slightly to the outside to allow water drainage. Refer to
installation instructions or check with installer.
Water dripping OUTSIDE when
unit is cooling.
Unit removing large quantity of moisture from humid room. This is normal during excessively humid
days.
Remote Sensing Deactivating
Prematurely (some models).
Remote control not located within range. Place remote control within 20 feet & 120° radius of the
front of the unit.
Remote control signal obstructed. Remove obstruction.
Room too cold.
Set temperature too low. lncrease set temperature.
Remote Sensing activated (on some models) and remote control located in Hot Spot - Relocate remote
control or deactivate remote sensing.
Trouble connecting the smart
Please visit Frigidaire.com and select the Owner Support section to view Frequently Asked Questions.
appliance to your wifi network or
experiencing an issue with the app.
If These Solutions Fail, Call 1-800-944-9044 For Frigidaire Service.
12
2009 Electrolux Home Products, Inc.
All rights reserved.
Major Appliance Limited Warranty
Your appliance is covered by a limited one-year warranty and a limited 2-5 year warranty on the sealed system (the compressor,
condenser, evaporator and tubing). For one year from your original date of purchase, Electrolux will pay all costs for repairing or
replacing any parts of this appliance that prove to be defective in materials or workmanship when such appliance is installed,
used and maintained in accordance with the provided instructions. From the second to the fifth year from your original purchase
date, Electrolux will repair or replace any parts in the Sealed Refrigeration System (compressor, condenser, evaporator and tubing)
that prove to be defective in materials or workmanship. In years 2-5, the consumer will be responsible for diagnostic, labor and
parts costs as well as any removal, transportation and reinstallation expenses which are incurred during service on components
other than those covered under the Sealed Refrigeration System 5-year warranty.
Exclusions
This warranty does not cover the following:
1. Products with original serial numbers that have been removed, altered or cannot be readily determined.
2. Product that has been transferred from its original owner to another party or removed outside the USA or
Canada.
3. Rust on the interior or exterior of the unit.
4. Products purchased "as-is" are not covered by this warranty.
5. Food loss due to any refrigerator or freezer failures.
6. Products used in a commercial setting.
7. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances not
in ordinary household use or used other than in accordance with the provided instructions.
8. Service calls to correct the installation of your appliance or to instruct you how to use your appliance.
9. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves,
etc., which are not a part of the appliance when it is shipped from the factory.
10. Service calls to repair or replace appliance light bulbs, air filters, water filters, other consumables, or knobs,
handles, or other cosmetic parts.
11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry trip
charges, or mileage expense for service calls to remote areas, including the state of Alaska.
12. Damages to the finish of appliance or home incurred during installation, including but not limited to floors,
cabinets, walls, etc.
13. Damages caused by: services performed by unauthorized service companies; use of parts other than
genuine Electrolux parts or parts obtained from persons other than authorized service companies; or external
causes such as abuse, misuse, inadequate power supply, accidents, fires, or acts of God.
14. Limitations and/or restrictions on smart appliance connectivity outside Electrolux’s control including, but not
limited to, software incompatibility, inadequate home wireless network capability/range and internet availability.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR OR
REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES, INCLUDING WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST
PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE YEAR. ELECTROLUX SHALL NOT BE LIABLE FOR
CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES
RESULTING FROM ANY BREACH OF THIS WRITTEN LIMITED WARRANTY OR ANY IMPLIED WARRANTY. SOME
STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS
OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS.
YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.
If You Need Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty period
Service
should service be required. If service is performed, it is in your best interest to obtain and keep all receipts.
Service under this warranty must be obtained by contacting Electrolux at the addresses or phone numbers below.
You will be responsible for any service charges incurred due to limitations and/or restrictions on smart appliance
connectivity outside Electrolux’s control including, but not limited to, software incompatibility, inadequate home
wireless network capability/range and internet availability.
This limited warranty only applies in the USA and Canada. In the USA, your appliance is warranted by Electrolux Major Appliances
North America, a division of Electrolux Home Products, Inc. In Canada, your appliance is warranted by Electrolux Canada Corp.
Electrolux authorizes no person to change or add to any obligations under this warranty. Obligations for service and parts under
this warranty must be performed by Electrolux or an authorized service company. Product features or specifications as described
or illustrated are subject to change without notice.
USA
1.800.944.9044
Electrolux Major Appliances
10200 David Taylor Drive
Charlotte, NC 28262
2009 Electrolux Home Products, Inc.
Canada
1.800.265.8352
Electrolux Canada Corp.
5855 Terry Fox Way
Mississauga, Ontario, Canada
L5V 3E4
All rights reserved.
13
Download PDF

advertising