Amana | PBE093G35CC | Installation instructions | Amana PBE093G35CC Installation Instructions

Amana PBE093G35CC Installation Instructions
THROUGH THE WALL
ROOM AIR CONDITIONER
WITH OPTIONAL ELECTRIC HEAT
INSTALLATION INSTRUCTIONS
RECOGNIZE THIS SYMBOL AS A SAFETY PRECAUTION.
ATTENTION INSTALLING PERSONNEL
As a professional installer you have an obligation to know the product better than the customer. This includes all
safety precautions and related items.
Prior to actual installation, thoroughly familiarize yourself with this Instruction Manual. Pay special attention to all
safety warnings. Often during installation or repair it is possible to place yourself in a position which is more
hazardous than when the unit is in operation.
Remember, it is your responsibility to install the product safely and to know it well enough to be able to instruct a
customer in its safe use.
Safety is a matter of common sense...a matter of thinking before acting. Most dealers have a list of specific good
safety practices...follow them.
The precautions listed in this Installation Manual are intended as supplemental to existing practices. However, if
there is a direct conflict between existing practices and the content of this manual, the precautions listed here take
precedence.
is a registered trademark of Maytag Corporation or its related companies and is used under
license to Goodman Company, L.P., Houston, TX. All rights reserved.
IO-370A
May 2010
www.amana-ptac.com
© 2010 Goodman Company, L.P.
TABLE OF CONTENTS
UNIT FEATURES
Important Note to Owner ............................................................. 2
Important Note to Servicer ........................................................... 2
This unit has many features which are different than those found
on conventional units. The servicer must be familiar with these
features in order to properly service the unit.
Operating Instructions ................................................................. 2
Unit Features ................................................................................ 2
Installation Instructions ............................................................... 3
Check the data specification plate and ensure the proper voltage
and current rating is available for the type power plug on the unit.
DO NOT REMOVE THE GROUNDING PRONG FROM THE POWER
CORD. Note the types of acceptable plugs in Figure 1.
Wiring ........................................................................................... 6
Air Conditioner Features ............................................................. 7
Refer to the data serial plate for electrical requirements.
Additional Information ................................................................ 11
Normal Operating Sounds and Conditions ............................... 11
Obtaining Service ....................................................................... 11
Consumer Warranty .................................................................. 12
Commercial Warranty ............................................................... 13
IMPORTANT NOTE TO THE HOMEOWNER
This manual is to be used by qualified, professionally trained HVAC
technicians only. Goodman does not assume any responsibility
for property damage or personal injury for improper service procedures or services performed by an unqualified person.
230V
20 Amp
120V
15 Amp
IMPORTANT NOTE TO THE SERVICER
Read this manual and familiarize yourself with the specific items
which must be adhered to before attempting to service this unit.
The precautions listed in this Installation Manual are intended as
supplemental to existing practices. However, if there is a direct
conflict between existing practices and the content of this manual,
the precautions listed here take precedence.
Figure 1
• LCDI or AFCI Power Cords - Underwriters Laboratories and
the National Electric Code (NEC) now require power cords
that sense current leakage and can open the electrical circuit to the unit on units rated at 250 volts or less. In the event
that unit does not operate, check the reset button located on
or near the head of the power cord as part of the normal
troubleshooting procedure.
LCDI Power Cord
Figure 2
OPERATING INSTRUCTIONS
Check the data specification plate and ensure the proper voltage
and current rating is available for the type power plug on the unit.
DO NOT REMOVE THE GROUNDING PRONG FROM THE POWER
CORD. Note the types of acceptable plugs on the following figure.
Refer to the data serial plate for electrical requirements.
VOLTAGE MEASUREMENTS
Before connecting the unit, measure the supply voltage. Voltage
must fall within the voltage utilization range given in the following
table.
2
CHASSIS INSTALLATION
Operating Voltage
Voltage Utilization Range
Unit Voltage
Rating
Minimum
Maximum
230/280
187
253
115
103
126
1. Remove front grille. See Figure A.
INSTALLATION INSTRUCTIONS
To ensure that the unit operates safely and efficiently, it must be
installed, operated, and maintained according to these installation and operating instructions and all local codes and ordinances,
or, in their absence, with the latest edition of the National Electrical
Code. The proper installation of this unit is described in the following sections. Following the steps in the order presented should
ensure proper installation.
SLEEVE INSTALLATION
Figure A
In order for condensate water to drain properly inside the unit, the
sleeve must be installed properly:
• Level from right to left.
•
The front grille can be removed for more thorough cleaning or to
make the model and serial numbers accessible. To remove, pull
the filter out and remove the two grille screws.
A slight downward pitch from the indoor side to the outdoor
side as shown in Figure 3.
Refer to the Installation Instructions supplied with the wall sleeve
for a complete description of the installation procedure.
NOTE: Wall sleeve (PBWS01A ) is not shipped with chassis and
must be purchased separately.
Inside
Outside
Wall
Sleeve
Level
1/4 Bubble
Tilt To
Outside
Outside
Wall
Pull the grille out from the bottom and lift up from the tabs on the
top of the case.
2. Remove the grounding screw and wire next to the grounding
symbol on right side of chassis control panel (Figure 3). Attach other end of ground wire to the hole in the bottom right
side of the sleeve with #8 x 3/8” blunt point sheet metal screw.
The hole on the sleeve is indicated by grounding symbol on
the sleeve. Slide chassis part of the way into the sleeve and
reattach the ground wire back to the hole on the right side on
the control panel area next to the grounding symbol.
Figure 2
REAR LOUVER PANEL
A TWKG rear louver panel kit is required for unit installation into an
existing Amana® brand 26” wall sleeve. A TWEAK or TWFAK adapter
kit is required for unit installation into an existing 27” wall sleeve.
The rear louver panel directs air flow for proper unit operation and
protects the outdoor coil. The panel must be installed before installing the chassis. These kits are not supplied with the unit.
Refer to the Installation Instructions supplied with the rear louver
panel kit for a complete description of the installation procedure.
3
Locking
Plate
Figure 3
Figure C
3. Remove shipping pads inside air conditioner next to
compressor. (See Figure B.)
6.
If outlet is on the left side of the unit, route power cord as
shown in Figure D.
Remove
shipping
pads
Clamp
Power
Cord
Figure B
4.
Carefully slide the chassis into the sleeve. Ensure that
the ground wire is not pinched or in the path of the
condenser fan.
5.
Loosen locking plate screw and rotate tab with tab
behind wall case flange (See Figure C) then tighten
locking plate screw.
Figure D
To replace front grille:
Hook the tabs on the front grille even with the tabs on the case and
snap into place. Replace the screws and filter. Refer to Page 3,
Figure A.
4
VENT CONTROL AND AIR DIRECTION (See Figure E)
AIR DIRECTION:
The vent control is located behind the front grille on the right side
of the air discharge area. When set at CLOSE only the air inside
the room will be circulated and conditioned. When set at OPEN,
some inside air is exhausted outside.
Horizontal louvers on the front grille let you control the air direction
up and down.
Locating
Hole
Locating
Hole
Screw Hole
Screw Hole
OPEN position
(Mesh end toward back)
CLOSE position
(Mesh end toward front)
Figure E
Remove the front grille to adjust the vertical louvers side-to-side
to direct the air left or right.
To open or close the vent:
1. Remove the front grille.
2. Remove the vent card screw.
3. Remove the vent card, turn it over and replace it by locating
rear hole in card over locating pin inside air discharge and
reattaching screw at front.
Screw
Figure 5
IMPORTANT NOTES:
1. The unit is equipped with a rubber-grommet-mounted
compressor. These grommets are factory set and require
no adjustment.
Figure 4
2. Obstruction to air flow must be checked and removed.
Check the indoor and outdoor grilles for obstructions. The
unit must be located where curtains, furniture, trees, or
other objects do not block air flow to and from the unit. If air
is obstructed and/or deflected back into the unit, the air
conditioner’s compressor may cycle on and off rapidly.
This could cause damage to the compressor.
5
WIRING
Before wiring the unit, please review the following warnings and
cautions.
6
AIR CONDITIONER FEATURES
ELECTRONIC CONTROL OPERATING INSTRUCTIONS
Before you begin, thoroughly familiarize yourself with all of the functions of the control panel and remote as shown below and follow the
instructions. The unit can be controlled by the touchpad alone or with the remote control.
RAISES
TEMPERATURE
OR TIME
SETS MODE
COOLING ONLY
UNIT
DISPLAYS
TEMPERATURE
AUTO
COOL
ENERGY
SAVER
FAN
ONLY
LOW
FAN
SPEED
+
MODE
TEMPERATURE/TIMER
TIMER
SLEEP MODE
TIMER
RAISES
TEMPERATURE
OR TIME
SETS MODE
HEAT/COOL UNIT
SETS FAN
SPEED
AUTO
HEAT
HIGH
COOL
MED
ENERGY
SAVER
FAN
ONLY
LOW
FAN
SPEED
POWER
DISPLAYS
TEMPERATURE
Set
+
MODE
TEMPERATURE/TIMER
SLEEP
TIMER
SLEEP MODE
TIMER
TURNS UNIT
ON OR OFF
LOWERS
TEMPERATURE
OR TIME
-
SLEEP
LOWERS
TEMPERATURE
OR TIME
Set
-
SETS FAN
SPEED
HIGH
MED
TURNS UNIT
ON OR OFF
POWER
ACTIVATES
TIMER
RAISES
TIME
SLEEP
Mode
LOWERS
TIME
_
TIMER
Select Mode
MO
SETS FAN
SPEED
LOWERS
TEMPERATURE
DE
SLEEP
+
AUT
O
RAISES
TEMPERATURE
∧
Fan
_
Fan
+
∨
ON/OFF
TURNS UNIT
ON OR OFF
REMOTE CONTROL
NOTE:
The remote control will work normally after a 5 second reset.
BATTERY SIZE:
AUTO
Mode
AAA
7
SETS FAN
SPEED
AIR CONDITIONER FEATURES
TO TURN UNIT ON:
MED
LOW
FAN
SPEED
AUTO
Set
ENERGY
SAVER
FAN
ONLY
MODE
+
TEMPERATURE/TIMER
SLEEP
COOL
MED
ENERGY
SAVER
FAN
ONLY
LOW
TIMER
POWER
FAN
SPEED
PRESS
ON/OFF
BUTTON
COOL
SLEEP
MED
LOW
FAN
SPEED
AUTO
ENERGY
SAVER
FAN
ONLY
MODE
+
TEMPERATURE/TIMER
SLEEP
TIMER
+
TIMER
POWER
YOU WILL SEE:
Set
-
HEAT
HIGH
MODE
Set
TEMPERATURE/TIMER
TO CHANGE TEMPERATURE SETTING:
AUTO
72
HEAT
HIGH
PRESS TO RAISE
PRESS TO LOWER
COOL
MED
ENERGY
SAVER
FAN
ONLY
LOW
FAN
SPEED
72
HEAT
HIGH
MODE
Set
-
COOL
-
HEAT
HIGH
-
AUTO
YOU WILL SEE:
+
TEMPERATURE/TIMER
SLEEP
POWER
TIMER
POWER
NOTE:
Tap or hold either up ( S ) or down ( T ) button until the desired temperature is seen on the display. This temperature will be
automatically maintained anywhere between 60°F (16°C) and 86°F (30°C) for both cooling and heating modes.
If you want the display to read the actual room temperature, select the FAN ONLY MODE.
COOL
MED
ENERGY
SAVER
FAN
LOW
FAN
SPEED
MODE
AUTO
Set
+
TIMER
COOL
MED
ENERGY
SAVER
FAN
LIGHT ON
LOW
FAN
SPEED
MODE
AUTO
Set
+
MODE
PRESS FAN SPEED
BUTTON
TIMER
+
TIMER
COOL
MED
ENERGY
SAVER
FAN
ONLY
FAN
SPEED
72
HEAT
HIGH
LOW
POWER
YOU WILL SEE:
MODE
+
Set
TEMPERATURE/TIMER
TEMPERATURE/TIMER
SLEEP
Set
TEMPERATURE/TIMER
SLEEP
POWER
-
HEAT
HIGH
ENERGY
SAVER
FAN
ONLY
SELECT SPEED
TO CHANGE AUTO FEATURE:
AUTO
COOL
MED
LOW
72
HEAT
HIGH
FAN
SPEED
TEMPERATURE/TIMER
SLEEP
PRESS FAN SPEED
BUTTON
-
HEAT
HIGH
-
AUTO
-
LIGHT ON
TO CHANGE FAN SPEEDS:
YOU WILL SEE
THE SPEED CHOSEN:
SELECT AUTO FAN
POWER
SLEEP
TIMER
POWER
NOTE:
The fan speed will automatically set to the speed needed to provide optimum comfort setting with the set temperature. If the room needs
more cooling, the fan speed will automatically increase. If the room needs less cooling, the fan speed will automatically decrease. Auto
fan speed cannot be used when in the FAN ONLY mode.
8
AIR CONDITIONER FEATURES
TO OPERATE ON FAN ONLY:
YOU WILL SEE:
HEAT
HIGH
COOL
MED
ENERGY
SAVER
FAN
ONLY
LOW
FAN
SPEED
MODE
Set
+
-
AUTO
AUTO
PRESS
MODE
BUTTON
COOL
MED
ENERGY
SAVER
FAN
ONLY
LOW
FAN
SPEED
+
MODE
TIMER
CHOOSE
FAN ONLY
POWER
Set
TEMPERATURE/TIMER
TEMPERATURE/TIMER
SLEEP
72
HEAT
HIGH
-
LIGHT ON
SLEEP
TIMER
POWER
Note: Use this function only when cooling is not desired, such as for room air circulation. You can choose any fan speed you prefer,
except AUTO FAN. During this function, the display will show the actual current temperature, not the set temperature as in the cooling
mode.
HEAT
HIGH
COOL
MED
ENERGY
SAVER
FAN
ONLY
LOW
FAN
SPEED
MODE
Set
+
-
AUTO
TEMPERATURE/TIMER
SLEEP
TIMER
POWER
YOU WILL SEE:
LIGHT ON
PRESS
MODE
BUTTON
AUTO
COOL
MED
ENERGY
SAVER
FAN
ONLY
LOW
FAN
SPEED
CHOOSE
ENERGY SAVER
72
HEAT
HIGH
MODE
Set
-
TO USE THE ENERGY SAVER FEATURE:
+
TEMPERATURE/TIMER
SLEEP
TIMER
POWER
Note: In this mode, the fan will continue to run for 1 (one) minute after the compressor or electric heat strip shuts off. This results in
wider variations of room temperature and is normally used when the room is unoccupied.
YOU WILL SEE
THE TIME CHOSEN:
HEAT
HIGH
COOL
MED
ENERGY
SAVER
FAN
LOW
FAN
SPEED
MODE
AUTO
Set
+
-
AUTO
TEMPERATURE/TIMER
SLEEP
TIMER
POWER
PRESS
TIMER BUTTON
COOL
MED
ENERGY
SAVER
FAN
ONLY
LOW
FAN
SPEED
THEN PRESS
TEMP/TIMER
BUTTON
0.5
HEAT
HIGH
MODE
+
Set
-
TIMER-DELAY START/STOP FEATURE:
TEMPERATURE/TIMER
SLEEP
TIMER
POWER
LIGHT ON
NOTES:
1. For DELAY STOP, the unit must be in the ON position.
2. For DELAY START, the unit must be in the OFF position.
To adjust the timer setting, tap or hold the UP ( S ) arrow or DOWN
( T ) arrow to change the delay time by 1/2 hour (0.5) increments
up to 10 hours; then 1 hour increments up to 24 hours. The
control will count down the time remaining until start or stop (8,
7.5, 7, etc.).
After setting the Timer, the unit will enter into Timer mode within
5 seconds. The Timer light will then be on and the Set light will
be off.
While in Timer mode, the Set temperature and fan speed will
maintain previously set temperature and fan speed and the Temperature display will show the set temperature. (There will be no
display if the power is turned off.) By pressing the Timer once,
the LED displays the remaining portion of the set time. (The LED
will return to set temperature within 5 seconds.) When in Fan
Only mode, the LED will only display the room temperature; it will
not display set temperature.
Turning the unit “ON” or “OFF” at any time will cancel the DELAY
START/STOP function. The DELAY START/STOP feature will work
until the unit starts or stops. Once this has happened, the above
steps must be repeated again.
NOTE: Factory default setting is for °F. To convert to °C, press the
INCREASE S / DECREASE T buttons simultaneously for
approximately 5 seconds. To return to °F, repeat the procedure.
9
AIR CONDITIONER FEATURES
HEATING FEATURE (on some models):
COOL
MED
ENERGY
SAVER
FAN
ONLY
LOW
FAN
SPEED
Set
+
MODE
HIGH
COOL
MED
ENERGY
SAVER
FAN
ONLY
LOW
FAN
SPEED
+
MODE
SELECT HEAT
TIMER
Set
TEMPERATURE/TIMER
TEMPERATURE/TIMER
SLEEP
72
HEAT
AUTO
PRESS
MODE
BUTTON
-
HEAT
HIGH
-
AUTO
YOU WILL SEE:
TIMER
SLEEP
POWER
POWER
Note: This feature can be used with any combination of FAN Speeds, Timer or Sleep Modes. When in the “heat” Mode, the fan will run
continuously while heat is needed. The temperature will automatically be maintained anywhere between 61°F (16°C) and 86°F (30°C).
SLEEP FEATURE:
COOL
MED
ENERGY
SAVER
FAN
ONLY
LOW
FAN
SPEED
Set
+
MODE
PRESS
MODE
BUTTON
-
HEAT
HIGH
HEAT
AUTO
HIGH
COOL
MED
ENERGY
SAVER
FAN
ONLY
LOW
FAN
SPEED
Set
+
MODE
TEMPERATURE/TIMER
TEMPERATURE/TIMER
SLEEP
TIMER
-
AUTO
YOU WILL SEE:
SELECT
SLEEP
POWER
TIMER
SLEEP
POWER
Note: After pressing this button, SLEEP ON and SLEEP OFF can be selected. After powered on, SLEEP OFF is defaulted. After the unit
is turned off, the SLEEP function is cancelled. If SLEEP mode is set while the unit is in COOL or ENERGY SAVER modes, the SET TEMP.
would increase 1.8°F (1°C) in 1 hour and 3.6°F (2°C) in 2 hours. If SLEEP mode is set while unit is in HEAT mode, the SET TEMP. would
decrease 1.8°F (1°C) in 1 hour and 3.6°F (2°C) in 2 hours. When unit is in FAN ONLY and AUTO modes, this function is not available.
TO TURN UNIT OFF:
YOU WILL SEE:
HEAT
HEAT
AUTO
HIGH
COOL
HIGH
COOL
MED
ENERGY
SAVER
FAN
ONLY
MED
ENERGY
SAVER
FAN
ONLY
FAN
SPEED
LOW
+
MODE
-
LOW
Set
SLEEP
TIMER
FAN
SPEED
PRESS
ON/OFF
BUTTON
TEMPERATURE/TIMER
POWER
+
MODE
TEMPERATURE/TIMER
SLEEP
TIMER
POWER
FAULT CODES
MED
LOW
FAN
SPEED
F1
ENERGY
SAVER
FAN
ONLY
MODE
AUTO
Set
COOL
MED
ENERGY
SAVER
FAN
ONLY
LOW
+
FAN
SPEED
MODE
TIMER
SLEEP
POWER
COOL
MED
LOW
FAN
SPEED
F4
ENERGY
SAVER
FAN
ONLY
MODE
AUTO
Set
+
TIMER
COOL
MED
ENERGY
SAVER
FAN
ONLY
FAN
SPEED
MODE
TIMER
SLEEP
POWER
If the display reads “F4”, a sensor has failed.
FJ
+
Set
TEMPERATURE/TIMER
TEMPERATURE/TIMER
SLEEP
POWER
HEAT
HIGH
LOW
-
HEAT
HIGH
+
If the display reads “F2”, a sensor has failed.
If the display reads “F1”, a sensor has failed.
AUTO
Set
TEMPERATURE/TIMER
TEMPERATURE/TIMER
SLEEP
F2
HEAT
HIGH
-
COOL
-
HEAT
HIGH
-
AUTO
Set
-
AUTO
TIMER
POWER
If the display reads “FJ”, a sensor has failed.
10
ADDITIONAL INFORMATION
• The remote control will operate all the control panel features.
Instructions will be the same.
• The “COOL” circuit has an automatic 3 minute time delayed start if the unit is turned off and on quickly. This
prevents overheating of the compressor and possible circuit breaker tripping.
NOTE: The fan will continue to run during this time.
• The control will maintain any set temperature between 60°F
and 90°F (cooling), 55°F and 80°F (heating).
• The control is capable of displaying temperature in degrees
(Fahrenheit) or degrees (Celsius). To convert from one to the
other, press and hold the UP and DOWN Temperature Selection Pads at the same time for 3 seconds.
COMPRESSOR
The compressor is hermetically sealed, permanently lubricated
and requires no additional oiling.
FRONT PANEL AND GRILLE
The front panel and grille can be cleaned with a mild soap or
detergent. Do not use hydrocarbon-based cleaners (e.g. acetone,
benzene, naphtha, gasoline, etc.) to clean the front panel or grille.
Use care when cleaning the control area. Do not use an excessively wet cleaning cloth.
NORMAL OPERATING SOUNDS
AND CONDITIONS
SCHEDULED MAINTENANCE
To achieve continuing top performance and high efficiency, a regular
cleaning/inspection schedule must be established. Maintaining
this schedule can be accomplished by either a local maintenance
staff or an authorized servicer and must follow the instructions
described in this manual.
POPPING OR GURGLING SOUNDS
This sound is the refrigerant traveling through the lines. This is a
normal sound which may be heard for a few seconds after the unit
shuts off.
• If the unit is operated in a dusty climate, dust may collect in
the basepan and clog the condenser coil. It is advisable to
remove the unit from the sleeve and thoroughly clean the
basepan and condenser coil on a periodic basis.
WATER TRICKLING SOUNDS
This sound is produced by the water as it is picked up and run
over the coils. This procedure improves the efficiency of the unit
and helps with water removal.
• If the unit is installed ocean side or in a corrosive atmosphere,
its life may be greatly reduced by the corrosive environment.
Under these conditions, the unit should be removed from the
sleeve and completely cleaned once a year. At that time any
scratches or blisters on the painted surfaces should be
sanded and repainted.
WATER DRIPPING
Water will collect in the basepan during high humidity days.
STARTING DELAY
You may notice a short delay in the startup if you try to restart the
unit too soon after turning it off or if you adjust the thermostat right
after the compressor has shut off. This delay protects the compressor.
OUTDOOR COIL CLEANING
The coils on the outdoor side of the air conditioner should be
checked regularly. For cleaning outside coil, remove the 6 screws
that mount the condenser coil top cover to condenser shroud.
Obtaining Service
In the unlikely event this unit requires repair or servicing beyond
what is covered in this manual, contact an authorized service organization.
To obtain an authorized servicer, contact your sales representative or agency.
11
12
Part No. PW-342B
5/2010
_________________________________
Date of Purchase
_________________________________
This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.
WHETHER ANY CLAIM IS BASED ON NEGLIGENCE OR OTHER TORT, BREACH OF WARRANTY OR OTHER BREACH OF CONTRACT, OR ANY OTHER THEORY, IN NO EVENT SHALL
WE BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT
LIMITED TO LOST PROFITS, LOSS OF USE OF A UNIT OR OTHERWISE. Some states do not
allow the exclusion or limitation of incidental or consequential damages, so the above
exclusion may not apply to you.
THIS WARRANTY IS THE ONLY EXPRESS WARRANTY PROVIDED ON THE UNITS COVERED;
AND ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO THE DURATION OF
THIS WARRANTY. Some states do not allow limitations on how long an implied warranty lasts,
so the above limitation may not apply to you.
•
•
•
•
•
•
•
•
1-877-254-4729 inside U.S.A. • 1-713-861-2500 outside U.S.A.
Goodman Consumer Affairs • 7401 Security Way • Houston, Texas 77040
For answers to questions regarding the above or to locate an authorized servicer, contact
For service, contact an Authorized Amana® Brand Servicer.
©2010 Goodman Company, L.P.
is a registered trademark of Maytag Corporation or its related companies and is used under license to Goodman Company, L.P., Houston, TX. All rights reserved.
Model # & Serial #
Goodman will not pay for electricity or fuel costs, or increases in electricity or fuel costs,
for any reason, including additional or unusual use of supplemental electric heat. This
warranty does not cover lodging.
The above remedies are our only responsibilities, and the consumer’s only remedies,
under this warranty. For warranty credit, any defective part must be returned to an
Amana® brand heating and air conditioning products distributor by an authorized
Amana® brand servicer; and all warranty service must be performed by an authorized
Amana® brand servicer. To locate an authorized Amana® brand servicer, contact
Goodman Company Consumer Affairs at the number or address found at the bottom of
this certificate.
Any part replaced or leak repaired under this warranty is warranted only for the unexpired portion of the original warranty term.
If the date of purchase cannot be verified, the warranty period begins three months after
the month of manufacture (indicated by the first four digits of the unit’s serial number
(yymm)).
SECOND THROUGH FIFTH YEARS SEALED SYSTEM COVERAGE: During the 2nd
through 5th years after the date of purchase, we will repair (to include labor) any refrigerant leaks caused by defects in workmanship or material of a unit, and will repair or
replace (to include labor) any portion of the evaporator coil, condenser coil, compressor,
reversing valves or connecting tubing that proves to be defective, in workmanship or
materials.
FIRST-YEAR COVERAGE (ENTIRE UNIT): We will repair or replace, free of charge (to
include labor), any part of a unit that proves to be defective due to workmanship or
materials within the first year after the date of purchase.
•
•
Amana® brand RAC window-type heating or air conditioning units identified as AE, AH,
PBC, PBE and PBH units are warranted by Goodman Company, L.P. to consumers
against defects in materials and workmanship under normal use and maintenance, as
provided below.
Damage or repairs required as a result of faulty installation or application
Damage or repairs required as a result of floods, fires, wind, lightning, accidents, corrosive
atmosphere or other conditions beyond our reasonable control
Damage or repairs required as a result of the use of components or accessories not
compatible with the unit
Units installed outside of the United States and Canada
Normal maintenance, as described in the installation and operating manual, such as
cleaning of the coils, filter cleaning and/or replacement, or damage caused by failure to
perform such maintenance
Parts or accessories not supplied or designated for use by us
Damage or repairs required as a result of any improper use, maintenance, operation or
servicing
Damage or failure to start due to interrupted and/or inadequate electrical service
Changes in the appearance of the unit that do not affect its performance
Replacement of fuses and replacement or resetting of circuit breakers
WARRANTY LIMITATIONS:
WE ARE NOT RESPONSIBLE FOR:
This warranty is extended only to purchasers for personal, family or household use. A
distinct warranty is extended to commercial customers.
RAC WINDOW TYPE H & C (AE, AH, PBC, PBE, PBH)
LIMITED WARRANTY
CONSUMERS
13
Part No. PW-343
5/2010
_________________________________
Damage or repairs required as a result of faulty installation or application
Damage or repairs required as a result of floods, fires, wind, lightning, accidents,
corrosive atmosphere or other conditions beyond our reasonable control
Damage or repairs required as a result of the use of components or accessories
not compatible with the unit
Units installed outside of the United States and Canada
Normal maintenance, as described in the installation and operating manual, such as
cleaning of the coils, filter cleaning and/or replacement, or damage caused by
failure to perform such maintenance
Parts or accessories not supplied or designated for use by us
Damage or repairs required as a result of any improper use, maintenance, operation or servicing
Damage or failure to start due to interrupted and/or inadequate electrical service
Changes in the appearance of the unit that do not affect its performance
Replacement of fuses and replacement or resetting of circuit breakers
Date of Purchase
_________________________________
THIS WARRANTY IS PROVIDED IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. WHETHER ANY CLAIM IS BASED ON NEGLIGENCE OR OTHER TORT, BREACH OF WARRANTY OR OTHER BREACH OF CONTRACT, OR ANY OTHER THEORY, IN NO EVENT SHALL WE BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LOST
PROFITS, LOSS OF USE OF A UNIT OR OTHERWISE.
•
•
•
•
•
•
•
•
•
•
WARRANTY LIMITATIONS:
WE ARE NOT RESPONSIBLE FOR:
Goodman will not pay for electricity or fuel costs, or increases in electricity or fuel
costs, for any reason, including additional or unusual use of supplemental electric heat.
This warranty does not cover lodging.
1-877-254-4729 inside U.S.A. • 1-713-861-2500 outside U.S.A.
Goodman Consumer Affairs • 7401 Security Way • Houston, Texas 77040
For answers to questions regarding the above or to locate an authorized servicer, contact
For service, contact an Authorized Amana® Brand Servicer.
©2010 Goodman Company, L.P.
is a registered trademark of Maytag Corporation or its related companies and is used under license to Goodman Company, L.P., Houston, TX. All rights reserved.
Model # & Serial #
The above remedies are our only responsibilities, and the customer’s only remedies,
under this warranty. For warranty credit, any defective part must be returned to an
Amana® brand heating and air conditioning products distributor by an authorized
Amana® brand servicer; and all warranty service must be performed by an authorized Amana® brand servicer. To locate an authorized Amana® brand servicer,
contact Goodman Company Consumer Affairs at the number or address found at the
bottom of this certificate.
Any part replaced or leak repaired under this warranty is warranted only for the
unexpired portion of the original warranty term.
If the date of purchase cannot be verified, the warranty period begins three months
after the month of manufacture (indicated by the first four digits of the unit’s serial
number (yymm)).
SECOND THROUGH FIFTH YEARS SEALED SYSTEM COVERAGE: During the 2nd
through 5 th years after the date of purchase, we will repair (to include labor) any
refrigerant leaks caused by defects in workmanship or material of a unit, and will
repair or replace (to include labor) any portion of the evaporator coil, condenser coil,
compressor, reversing valves or connecting tubing that proves to be defective, in
workmanship or materials.
FIRST-YEAR COVERAGE (ENTIRE UNIT): We will repair or replace, free of charge
(to include labor), any part of a unit that proves to be defective due to workmanship
or materials within the first year after the date of purchase.
Amana® brand RAC window-type heating or air conditioning units identified as AE,
AH, PBC, PBE and PBH units are warranted by Goodman Company, L.P. to commercial
customers against defects in materials and workmanship under normal use and
maintenance, as provided below.
This warranty is extended to commercial customers only. A distinct warranty is
extended to purchasers for personal, family or household use.
RAC WINDOW TYPE H & C (AE, AH, PBC, PBE, PBH)
WARRANTY TO COMMERCIAL CUSTOMERS
THIS PAGE LEFT INTENTIONALLY BLANK
14
THIS PAGE LEFT INTENTIONALLY BLANK
15
is a registered trademark of Maytag Corporation or its related companies and is used under
license to Goodman Company, L.P., Houston, TX. All rights reserved.
www.amana-ptac.com
© 2010 Goodman Company, L.P.
16
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising