OPERATING INSTRUCTIONS Dishwasher DOD651PHXXLS Contents Display panel Important safety instructions Before washing for the first time Loading the dishwasher Using the dishwasher Settings 2 3 4 5 8 12 Care and maintenance instructions Troubleshooting Technical information Installation instructions Service Quick start guide 14 16 19 20 23 24 Dear Customer, Thank you for choosing this quality product from ASKO. We hope it will meet your expectations and fulfill your needs for many years to come. Scandinavian design combines clean lines, everyday functionality, and high quality. These are key characteristics of all our products and the reason they are greatly appreciated throughout the world. To get the most out of your new dishwasher, we recommend that you read the operating instructions before using it. The last page also includes a Quick start guide. Display panel To switch on the dishwasher, press and hold the main power switch until the display lights up. "Welcome to your new ASKO. This is a first time set up." is shown on the display the first time the dishwasher is switched on. It is important that you choose the right settings to ensure good dishwashing results. See page 4. Main power switch Display Start/Stop START Eco STOP 2:00 Speed mode Program mode selector Navigation buttons for selecting a program 2 Option Delayed Start Option Extra Dry Important safety instructions SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE WARNING! • Should a child swallow dishwasher detergent or rinse aid, give plenty to drink immediately, i.e., one or two glasses of milk or water. Do not try to induce vomiting. Seek medical advice immediately: Call the National Capital Poison Center at 1-800-222-1222. When using your dishwasher, follow basic precautions, including the following: • Always close the door and start the dishwasher as soon as you put in the detergent. • Read all instructions before using the dishwasher. • Always keep small children away from the machine when it is open. There may be some detergent residue left inside the machine. • Use the dishwasher only for its intended function. • Use only detergents or wetting agents recommended for use in a dishwasher and keep them out of the reach of children. • When loading items to be washed: – locate sharp items so that they are not likely to damage the door seal, and – load sharp knives with the handles up to reduce the risk of cut-type injuries. • If dishwasher detergent gets in someone’s eyes, rinse them with plenty of water for at least 15 minutes. Activate child lock (Kid Safe™) You can activate the child lock (button lock) to prevent children from starting the dishwasher. See the chapter Settings. Outdoor use • Do not wash plastic items unless they are marked “dishwasher safe” or the equivalent. For plastic items not so marked, check the manufacturer’s recommendations. • Always keep the door closed when not loading or unloading the machine to ensure that water does not penetrate the electrical components or control panel. • Do not operate the dishwasher unless all enclosure panels are properly in place. Winter storage • Do not tamper with controls. • Do not abuse, sit on, or stand on the door or dish rack of the dishwasher. • To reduce the risk of injury, do not allow children to play in or on a dishwasher. • Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for two weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for two weeks, before using the dishwasher turn on all hot water faucets and let the water flow from each for several minutes. This will release any accumulated hydrogen gas. As the gas is flammable, do not smoke or use an open flame during this time. • Remove the door to the washing compartment when removing an old dishwasher from service or discarding it. • Read the grounding instructions in the installation instructions. General • Do not run the dishwasher while you are out of the home. • Do not store or use combustible materials, gasoline, or other flammable vapors and liquids in the vicinity of this or any other appliance. See the Winter storage section in the Care and maintenance instructions chapter. Transport • Avoid long transport distances in very cold weather. • Transport the dishwasher upright or laying on its back. Overflow guard function The overflow protection starts pumping out the machine and turns off the water supply if the water level in the dishwasher exceeds the normal level. If the overflow protection is triggered, turn off the water supply and call the Customer Care Center. Packing material The packaging protects the product during transport. The packaging material is recyclable. Separate the different packaging materials to help reduce raw material use and waste. Your dealer can take the packaging for recycling or direct you to the nearest recycling center. The packaging is comprised of: • Corrugated cardboard made from up to 100% recycled material. • Expanded polystyrene (EPS) with no added chlorine or fluorine. • Disconnect electrical power to dishwasher before servicing. • Supports made from untreated wood. • Repairs should be done by a qualified technician. • Protective plastic made from polyethylene (PE). WARNING! PROPOSITION 65 FOR CALIFORNIA RESIDENTS Cancer and Reproductive Harm – www.P65Warnings.ca.gov Installation See the chapter Installation instructions. Disposal • When the machine has reached the end of its service life and is to be disposed of, it should immediately be made unusable. Pull out the power cable and cut it as short as possible. • The dishwasher is manufactured and labeled for recycling. • Contact your municipality for information about where and how your dishwasher can be recycled correctly. Child safety TIP! Dishwasher detergents and rinse aids are corrosive, so always keep them out of reach of children. 3 Before washing for the first time 1. Checking water hardness 2. Basic settings Contact the local water utility to check the water hardness in your area. This is important to determine how much detergent and rinse aid to use. To switch on the dishwasher, press and hold the main power switch until the display lights up. In general, more rinse aid and detergent are needed for hard water. "Welcome to your new ASKO. This is a first time set up." is shown on the display. It is important that you choose the right settings to ensure good dishwashing results. Select setting Main power switch Confirm setting Settings 1 Language Select the language to be shown on the display. 2 Rinse aid 0/1/2/3/4/5 Use rinse aid to improve wash and dry times. Also use rinse aid to achieve clear and spotless results. Select rinse aid dosage. The rinse aid dispenser can be adjusted between 0 (Off) and 5 (High dosage). Pre-selected at factory: 5 To change the chosen setting, see the chapter Settings. 4 Loading the dishwasher 3. Top up with rinse aid Energy-efficient dishwashing Use rinse aid to improve wash and dry times. Also use rinse aid to achieve clear and spotless results. Run programs only with a full load Wait until the dishwasher is fully loaded before running a program, this way you save energy. Use the Rinse and hold program to rinse the dishes if there are any unpleasant odors while you wait for the dishwasher to become fully loaded. Press to open Run programs at a lower temperature If the dishes are only lightly soiled, you can select a program with a low temperature. Select Green mode The dishwasher has different program modes. To save energy and water, use Green mode. 1 Open the rinse aid compartment lid. 2 Carefully top up with rinse aid. Only add rinse aid to the level marked max. 3 Wipe up any spilled rinse aid around the compartment. 4 Close the lid firmly. Add rinse aid When the rinse aid needs topping up, the above symbol lights on the display. After topping up, it may take a while before the symbol goes out. NOTE! Increase the rinse aid dosage: • If the dishes have water marks. Reduce the rinse aid dosage: • If the dishes have a sticky white/blue film. • If the dishes are streaked. • Heavy foaming. If you have very soft water, the rinse aid can be diluted 50:50 with water. Better drying results are achieved if you open the door a little once the program has ended. (If the dishwasher is built-in, the surrounding furnishings must be resistant to any condensation from the dishwasher.) Do not rinse under running water Simply scrape off large food particles before loading the dishwasher. Choose a green detergent Read the environmental declaration on the packaging! Connect to cold water Connect the dishwasher to the cold water supply if the building is heated using oil, electricity, or gas. Connection to hot water supply Connect the dishwasher to the hot water supply (max. 160 °F (70 °C)) if the building is heated using an energy-efficient means such as district heating, solar power, or geothermal power. Choosing a hot water connection cuts dishwashing times and reduces the dishwasher's energy consumption. NOTE! Do not exceed the permitted water supply temperature. Certain materials used in some cookware cannot withstand strong heat. 5 Fragile dishes The baskets Some cookware is not dishwasher safe. This can be for several reasons. Some materials cannot withstand high temperatures, others can be damaged by dishwasher detergent. The dishwasher includes an upper, a lower, and a cutlery basket. Use caution with, for example, handmade items, fragile decoration, crystal/glassware, silver, copper, tin, aluminum, wood, and plastic. Look for the "Dishwasher safe" marking. Upper basket Fragile decoration Porcelain with decoration on top of the glazing (the items feel rough) should not be washed in a dishwasher. The basket appearance may differ depending on the configuration. Place glasses, cups, bowls, side plates, and saucers in the upper basket. Place all soiled surfaces down! Place wine glasses on the wine shelf. Place knives on the knife stand, if applicable. Crystal/Glass Wash fragile items made of crystal/glass, such as crystal glass from Orrefors, using the gentle dishwashing program Crystal glass. Remember to use a small amount of detergent and to place items so that they do not touch each other during the wash. Use rinse aid to improve wash and dry times. Also use rinse aid to achieve clear and spotless results. Hand-painted glassware, as well as antique and very fragile items, should not be washed in a dishwasher. Silver Silver and stainless steel items should not come into contact, as the silver can become discolored. Aluminum Aluminum can lose its shine if washed in a dishwasher. However, good quality aluminum pans can be washed in a dishwasher, even if some of the shine will be lost. Cutlery with glued handles Some types of glue are not dishwasher safe. In such cases, the handles may loosen. Points to consider • All dirty surfaces should face in and down! • Dishes should not be placed in or on each other. • Angle dishes with hollows, such as cups, so that the rinse water will run off. This is also important for plastic items. Raising the upper basket 1 Pull out the upper basket. • Place the upper basket in its highest position when dishwashing very large plates. 2 Grab the sides of the upper basket with both hands and lift it up. • Make sure small items cannot fall through the dishwasher basket; place them in the cutlery basket. NOTE! Lowering the upper basket 1 Pull out the upper basket. 2 While holding the basket, pull out the two locking handles on either side to lower the upper basket. Check that the spray arms can rotate freely. Lower basket Place plates, side plates, serving dishes, pots, and cutlery (in the cutlery basket) in the lower basket. Place pots and pans in the rear right of the lower basket to best utilize dishwashing performance from the rear spray nozzle (WideSpray™), which is intended for these types of dishes. 6 Accessory Buy an extra cutlery basket. The extra cutlery basket is flexible and can be dismantled and attached to the lower basket or the large cutlery basket to make an extra large cutlery basket. This accessory is available where you bought the dishwasher. 2 1 Foldable tines Lower the foldable tines when washing large pots. Release the foldable tines by pressing the catch inward before adjusting their position. Washing large plates Move adjustable tines and their mounts to widen the distance between the tine rows to adapt the lower basket to plates with a diameter greater than 9 3/4" (25 cm). Cutlery basket Place cutlery with the handles facing down, except for knives, and spread them out as much as possible. Ensure that spoons do not stack inside each other. The cutlery basket is best placed in the middle at the front of the lower basket to best utilize dishwashing performance from the unique spray nozzle (Power Zone Cutlery™), which is intended for the cutlery basket. WARNING! Knives and other pointed items must be placed with the points down in the cutlery basket or horizontally in other baskets. Fold-down section for small items The cutlery basket has a fold-down section in the middle for small items, or small shafts, such as electric whisk attachments. 7 Using the dishwasher Typical load Add detergent Recommended for daily, regular, or typical use. Press to open Upper basket 1 Prewash detergent compartment 2 Main wash detergent compartment Detergent is added according to water hardness. Follow the instructions on the detergent packaging. Too much detergent can result in less effective dishwashing and also entails greater environmental impact. NOTE! Ensure the upper basket is set to its lowest position. Lower basket The detergent compartment must be dry when adding detergent. There is one compartment for the prewash and one for the main wash. If powder or liquid dishwasher detergent is used, add a small amount of the detergent to the prewash compartment. Contact the detergent manufacturer if you have questions about the detergent. NOTE! Use only dishwasher detergent! Liquid hand-washing detergent must not be used as the foam that forms prevents the dishwasher from operating effectively. Dishwasher tablets Halve the tablet if it is difficult to close the dispenser lid. There is a risk that the detergent will not be released properly if the lid is tight and cannot open correctly. NOTE! Dishwasher tablets are not recommended for short programs (less than 75 minutes). Use powder or liquid dishwasher detergent instead. All-in-one detergent There are many types of all-in-one detergents on the market. Read through the directions for these products carefully. NOTE! Optimal washing and drying results are achieved by using normal dishwasher detergent together with separately dispensed rinse aid. 8 Press and hold the main power switch until the display lights up. Starting the dishwasher START Eco STOP 2:00 Speed mode Select the program Select a program mode The main power switch Press and hold the main power switch until the display turns on. Also check that the water supply valve is on. Select a program To select a program, press the Navigation button or until the desired program is shown on the display. Select a program to suit the type of dishes and how dirty they are. Normal wash This program is recommended for daily, regular, or typical use to completely wash a full load of normally soiled dishes, such as plates, serving dishes, cups, and glasses. No options are recommended. ECO wash This program is most effective in terms of combined energy and water consumption. Sanitation wash An effective program for daily use with slightly dried leftovers. (This program is not intended for burnt food, such as on oven dishes.) Time program The program adapts to the specified running time or finish time. With this program, it is important to choose a time suited to how dirty the dishes are. 0:15-0:45 Lightly soiled dishes 1:00-1:30 Normally soiled dishes 2:00-2:30 Heavily soiled dishes – To set the desired program time, press and hold the option button to set the desired program length. Rinse and hold Use to rinse dishes while you wait for the dishwasher to become fully loaded. Plastic wash A program intended for washing plastic items that are dishwasher safe. This program has an extra long drying cycle. Porcelain and glasses can also be washed. Hygiene wash This program is recommended for baby bottles and cutting boards when additional sanitation is required. The temperature is high in the main wash and in the final rinse. Crystal glass A gentle dishwashing program with a low temperature for washing fragile items made of crystal/glass, such as crystal glass from Orrefors. Remember to use a small amount of detergent and to place items so that they do not touch each other during the wash. See also Fragile dishes in the chapter Loading the dishwasher. Porcelain that has just Select any options been used without dried leftovers can also be washed using this program. Self-cleaning Self-cleaning program for sanitizing the dishwasher tub, spray arms, and spray pipes. This program should be run (with no dishes in the machine) using regular dishwasher detergent or citric acid. Special dishwasher cleaners are also available in stores. For the removal of limescale deposits, see The dishwasher tub in the chapter Care and maintenance instructions. Select a program mode To select a program mode, press the program mode selector until the desired mode is shown on the display. The available program modes vary between programs. For a brief description, press and hold the program mode selector. Green mode The dishwasher uses less energy and water. The program time is extended. Speed mode The program time is shortened, but the dishwasher uses more energy and water. Night mode Lower noise level during the dishwashing program. The program time is extended. Intensive mode (Heat Boost) Improves the dishwashing results, but the dishwasher uses more energy and water. The program time is extended. Select an Option To select an option, press the option button until the desired option is shown on the display. The available options vary between programs. Extra Dry (Heated drying option) A higher temperature in the final rinse and a longer drying cycle improve the drying results if you activate this option. Energy consumption is slightly increased. For a brief description, press and hold the button for Extra Dry. Delayed Start When you select Delayed Start, the dishwasher will start 1-24 hours after you have pressed the button Start/Stop and closed the door. 1 Press the button once to activate Delayed Start. Press the button several times – or hold it in – to set the desired number of hours. 2 Press Start/Stop and close the door. The timer counts down and the dishwasher starts after the selected delay. If you want to cancel the Delayed Start option, open the door and press and hold the main power switch until the display turns off. 9 START STOP Starting the dishwasher Press and hold Start/Stop until the display shows "Program started, close door in 4 sec". This indicates that the dishwasher is ready to start. Close the door properly within four seconds, otherwise the dishwasher will not start. If the dishwasher is not started or the door is not closed within 2 minutes of the last button press, the machine switches off. Time remaining Once you have chosen a program, program mode, and options, the time the program took when last used is displayed. Stopping or changing a program If you want to change the program after starting the dishwasher, open the door then press and hold Start/Stop for three seconds. Add more detergent if the lid of the detergent dispenser has opened. Then choose a new program, press Start/Stop, and close the door within four seconds. If you want to load more dishes Open the door. The dishwasher stops automatically. Add the dishes. Press Start/Stop and close the door within five seconds. WARNING! If the door is open, "Program paused" is shown on the display. If you want the dishwashing program to continue, press Start/Stop and close the door immediately. If you want to cancel the dishwashing program, press and hold Start/Stop for three seconds. If the dishwasher is turned off due to a power failure If the program was not finished, the interrupted program resumes when power is restored. NOTE! During drying, the program is interrupted if the power is cut or the door is open for more than 2 minutes. Once the program has finished Once the program has finished and the door is opened, "END" appears on the display. At the end of the program, one short signal will sound. Chapter Settings describes how to change this function. The dishwasher switches off automatically after the program ends. To minimize the risk of leaks, we recommend that you turn off the water supply valve if away from home for an extended period of time. How to get the best drying results • Fully load the dishwasher. • Angle dishes with hollows, such as cups, so that the rinse water will run off. This is also important for plastic items. • Top up with rinse aid or increase the rinse aid dosage level. • Activate the Extra Dry option. • Activate the High temperature setting. See the chapter Settings. • Open the door a little once the program has finished. • Allow the dishes to cool before unloading the dishwasher. 10 Unloading the dishwasher Hot porcelain is more fragile. Leave the dishes to cool in the dishwasher before unloading them. Unload the lower basket first to avoid any water drops from the upper basket falling onto the dishes in the lower basket. 25 25 25 25 Normal wash 4) ECO wash Sanitation wash Time program 2 2-3 60 °C 140 °F <65 °C <150 °F 0.8 1:20 1:00 0.5 0.9 0.6 2.5 2.8 3.3 0.9 The energy label performance figures are based on this program. This program is recommended for daily, regular, or typical use to completely wash a full load of normally soiled dishes, such as plates, serving dishes, cups and glasses. No options are recommended. 1:50 1.4 2:25 0.01 2.9- 5.0 4.2 3.2 3.49 Connection to hot water, approx. 120 °F (50 °C). 50 °C 120 °F 1:30 1.1 0:07 0.4-1.2 0.6 0.6 0.5 Energy (approx. kWh) 4) 2 45 °C 115 °F 70 °C 160 °F 2:55 0.01 0:15-2:30 1:35 2:05 2:00 Dishwashing time (approx. hrs:min) Water cons. (gallon) Connection to cold water, approx. 50 °F (10 °C). (A cold water supply is recommended.) 2 70 °C 160 °F 68 °C 155 °F 0:07 --- °C --- °F 0.5-1.6 1.2 0.9 1.0 1) Hot water 3) Consumption values 3) 2 50 °C 120 °F 0:15-2:30 2:05 2:20 2:20 Energy (approx. kWh) Cold water 2) Dishwashing time (approx. hrs:min) <65 °C <150 °F 65 °C 150 °F 50 °C 120 °F 58 °C 136 °F Final rinse Consumption values vary depending on the temperature of the incoming water, room temperature, load size, selected additional functions, and more. 20 Crystal glass 2 55 °C 130 °F 1 2 Number of rinses 50 °C 122 °F Main wash 2) 25 Hygiene wash 1 0-2 2 1 1 Prewashes 1) 25 Plastic wash Rinse and hold Detergent, compartment 2 (ml) Program Program chart 11 Settings Open the dishwasher's Settings menu To open the dishwasher's Settings menu, press the Navigation button with the mode selector . or until Settings menu is shown on the display and confirm your selection To exit the dishwasher's Settings menu, select Exit and confirm your selection with the mode selector . Navigation buttons for choosing setting Mode selector to confirm current setting START 1� Language Settings English STOP Current setting Settings Options 1. Language English US/Svenska/Français/ Deutsch/Italiano/Suomi/Español/ Norsk/Dansk/Nederlands You can choose the language used for the display. 2. Select programs Normal wash On/Off ECO wash On/Off Sanitation wash On/Off Time program On/Off Rinse and hold On/Off Plastic wash On/Off Hygiene wash On/Off Crystal glass On/Off Self-cleaning On/Off Programs can be shown or hidden in the menu. Choose between On and Off. On/Off You can activate the child lock (button lock) to prevent children from starting the dishwasher. 3. Child lock (ECO wash cannot be hidden in the menu.) To temporarily deactivate and activate the child lock, press and hold the left Navigation button and the option button Delayed Start for 3 seconds. 4. Display settings Contrast top display1/2/3/4 For adjusting the contrast of the display. Logo in top display On/Off Setting to hide the logo shown on the display. 5. Feedback sound 0/1/2/3 This sound is used to confirm each button press. 6. Buzzer volume 0/1/2/3 The buzzer indicates when a dishwashing program has ended. Error messages are always indicated by a loud buzzer. 7. Rinse aid 0/1/2/3/4/5 Setting for rinse aid dosage. The rinse aid dispenser can be adjusted between 0 (Off) and 5 (High dosage). Increase the rinse aid dosage: • If the dishes have water marks. Reduce the rinse aid dosage: • If the dishes have a sticky white/blue film. • If the dishes are streaked. • Heavy foaming. If you have very soft water, the rinse aid can be diluted 50:50 with water. 12 Settings Options 8. On/Off Super rinse Super rinse adds two extra rinses. Activated in the following programs: Normal wash ECO wash Sanitation wash Plastic wash 9. High temperature On/Off Activate the setting High temperature to improve the dishwashing results. Energy consumption is slightly increased. Activated in the following programs: Normal wash ECO wash Sanitation wash Plastic wash 13 Care and maintenance instructions Coarse filter The coarse filter traps larger food particles, which cannot get past the drain pump. Empty the coarse filter as necessary. Upper spray arm 1 Pull out the upper basket. 2 Unscrew the spray arm bearings counterclockwise to remove the spray arm from the upper basket. Coarse filter 1 Lift the coarse filter by the handle. Lower spray arm • Pull the lower spray arm straight up to release it. 2 Empty the coarse filter. Remember to replace it! Fine filter Debris that collects on the fine filter is automatically rinsed away during each wash. Clean the fine filter when necessary. Fine filter 1 Turn the handle counterclockwise. 2 Lift the filter straight up using the handle. Remove the coarse filter to clean the fine filter. 3 Rinse the fine filter and scrub it clean with a dish brush and liquid hand-washing soap. 4 Replace in reverse order. Check that the edges seal properly when replacing the fine filter. 5 Lock the filter in place by turning the handle clockwise to the stop position. The handle should point straight out from the dishwasher. Cleaning the outside of the machine • Use only a slightly damp cloth (with a little cleaner if necessary) when cleaning the outside of the machine. Do not use solvents, as these can damage the machine. • If the surface discolors or rust appears, clean the surface immediately with a non-abrasive cloth. Display panel Keep the buttons clean and free from grease. Wipe them clean with a dry or slightly damp cloth. Never use cleaners – they can scratch the surface. Use the main power switch to turn off the dishwasher before cleaning the buttons to avoid activating any buttons unintentionally. NOTE! The dishwasher tub The dishwasher must not be used without the filters in place! The dishwasher tub is made of stainless steel and is kept clean through normal use. Dishwashing results may be affected if the coarse filter is incorrectly fitted. Spray arms Holes and bearings can become blocked. Remove debris using a needle or similar item. The spray arms have holes on the bottom. Limescale deposits If you have hard water, limescale deposits may build up in the dishwasher. If this happens, run the Self-cleaning program with two tablespoons of citric acid in the detergent compartment (with no dishes in the machine). Special dishwasher cleaners are also available in stores. Never use anti-freeze, Draino®, CLR®, or other chemical cleaners. Unblocking the drain pump If the dishwasher still contains water after the program has finished, something may be blocking the drain pump. Such items are easily removed. 1 Turn off the machine using the main power switch and unplug it from the power outlet. 2 Remove the coarse filter and the fine filter. 3 Scoop out the water from the dishwasher tub. Spray arms can be removed for cleaning. Remember to fit them firmly back into place afterward. 14 4 In order to inspect the drain pump, remove the colored stop on the right in the bottom drain. 5 Turn the pump wheel located behind the drain pump stop by hand. Carefully remove any items. Winter storage 6 Replace the drain pump stop along with the fine and coarse filters. If the dishwasher is to be stored outdoors where the temperature can fall below freezing, do as follows: 7 Plug the machine in again. If the dishwasher still does not start and a whirring sound is heard, the overflow protection has been triggered. • Shut off the water. • Unplug the unit from the power outlet. • Call the Customer Care Center. 1 Look under the cabinet adjacent to the dishwasher for a white, plastic type hose leading away from the dishwasher. This hose is the dishwasher PEX fill hose. Follow this hose away from the dishwasher to where it connects to a shut-off valve. Turn this shut-off valve completely off. 2 Open the dishwasher door, choose any program, press Start/Stop, and close the dishwasher door. You will hear the drain pump come on to begin the cycle. Once you hear the drain pump stop, open the door and cancel the cycle by holding the Start/Stop button for three to five seconds. 3 Turn the dishwasher off with the main power switch. Drain pump stop 4 Go back under the cabinet to the shut-off valve for the dishwasher. Lay an old towel under the shut-off valve and dishwasher fill line. The towel will soak up any water that comes out of the hose or valve. 5 Disconnect the dishwasher fill line from the shut-off valve using a 11/16" (17 mm) wrench or an adjustable wrench. 6 When you no longer see water dripping from the fill line or shut-off valve, remove the towel. NOTE! 7 Remove the dishwasher power cord from the receptacle. Do not forget to replace the drain pump stop. 15 Troubleshooting Type of fault on the display Action F10 Overfilling water 1 Clear the drain pump. See the section Care and maintenance instructions. If the problem persists, call the Customer Care Center. F11 Water outlet fault See “Water remains in the dishwasher above the filters” in the table “Problem” below. If the problem persists, call the Customer Care Center. F12 Water inlet fault Check that the water supply valve is on. If the problem persists, call the Customer Care Center. The water pressure should be 4.2-140 psi. F40 Inlet valve leakage Turn off the water supply valve and call the Customer Care Center. F52 Water level fault Check that the drain hose is fitted in accordance with the installation instructions. If the problem persists, call the Customer Care Center. F54 Overfilling water 2 Turn off the water supply valve and call the Customer Care Center. F56 Circ. pump fault Call the Customer Care Center. Press any button to clear the error message. Problem Possible causes Action The buttons do not react when pressed. You have pressed the buttons too soon after Wait a moment then try again. opening the door. Cannot close door. Child lock (button lock) activated. See the chapter Settings. The door is closed. Open the door. The buttons only react to use when the door is open. The buttons are dirty. Clean with a dry or slightly damp cloth. The baskets are not correctly positioned. Check that the baskets are correctly positioned horizontally. Check that the dishes are not blocking the baskets from sliding properly into place. The dishwasher does not start. The Start/Stop start button has been pressed for Press and hold Start/Stop until the display shows too short a time. "Program started, close door in 4 sec". The door is not closed properly or was not closed Close the door within four seconds, otherwise immediately after pressing the Start/Stop button. the dishwasher will not start. You have opened the dishwasher to add more dishes while a program is in progress. If you want the dishwashing program to continue, press Start/Stop and close the door within five seconds. A fuse/circuit breaker has been tripped. Check. The plug is not plugged into the power outlet. Check. The water supply valve is turned off. Check. Overflow/leaks. Check. A whirring sound (the drain pump) is heard from Turn off the water supply valve. Pull out the plug the dishwasher and does not stop when the main and call the Customer Care Center. power switch is turned off. Check that the Delayed Start option has not been Press and hold Start/Stop for three seconds if selected. you want to cancel the Delayed Start option. 16 Problem Possible causes Action The dishes are not clean. The spray arms do not rotate. Check that the dishes are not blocking the spray arms. Spray arm holes or bearings blocked. Clean the spray arms. See the chapter Care and maintenance instructions. Unsuitable dishwashing program. Choose a longer program. Incorrect detergent dosage. Dose according to water hardness. Far too much or far too little detergent can result in poor dishwashing results. Detergent is too old. Detergent is a perishable product. Avoid large packages. Dishes loaded incorrectly. Do not cover dishes with large bowls or lids. Avoid placing very tall glasses in the corners of the baskets. Glasses and cups have toppled over during the Load the dishes securely. program. The filters are not fitted correctly. Spots on stainless steel or silver. Spots or films on the dishes. Check that the filter handle is locked in the stop position. The handle should point straight out from the dishwasher. Some types of food, such as mustard, Rinse off these types of food if not starting the mayonnaise, lemon, vinegar, salt, and dressings, dishwasher immediately. Use the Rinse and hold can mark stainless steel if left for too long. program. All stainless steel can cause spots on silver if they come into contact during dishwashing. Aluminum can also cause spots on dishes. In order to avoid marks and tarnishing, separate dishes made from different metals, such as silver, stainless steel, and aluminum. Incorrect rinse aid dosage setting. See the chapter Settings. Too high temperature and/or too much detergent Wash crystal at a low temperature and with a can cause etching on crystal. Unfortunately, this conservative amount of detergent. Contact the cannot be repaired, only prevented. detergent manufacturer. The dishes have a sticky white/blue film. Rinse aid dosage setting too high. Reduce the dosage. See the chapter Settings. If you have very soft water, you may want to dilute the rinse aid 50:50 with water. Spots left after washing. Lipstick and tea can be difficult to wash off. Use a detergent with a bleaching agent. Detergent residue in the detergent compartment The detergent compartment was damp when after dishwashing. adding detergent. The detergent compartment must be dry when adding detergent. The detergent compartment has been blocked. Check that the dishes are not preventing the detergent compartment from opening. Rattling sound when dishwashing. The dishes are not correctly placed or the spray Check that the dishes are placed securely. Spin arms are not rotating. the spray arms to make sure they can rotate. "Program paused" is shown on the display. The dishwasher door has been opened while a If you want the dishwashing program to continue, program is in progress. press Start/Stop and close the door within five seconds. If you want to cancel the dishwashing program, press and hold Start/Stop for three seconds. 17 Problem Possible causes Water remains in the dishwasher above the filters. The filters are blocked. Bad odor in dishwasher. Action Clean the coarse and fine filters. The filters are not fitted correctly. Check that the filter handle is locked in the stop position. The handle should point straight out from the dishwasher. Debris in the drain pump. Clean the drain pump. See the chapter Care and maintenance instructions. Kink in drain hose. Check that the hose is free from kinks and sharp bends. Blocked drain hose. Loosen the drain hose from where it terminates. Check that no debris has clogged the hose. Is the cone-shaped part of the drain boot cut to the maximum size of the fitting where it attaches? Dirt around the seals and in corners. Clean with dish brush and low foaming cleaner. Low temperature programs have been selected Run a program with a higher temperature once for a prolonged period. or twice a month. Or run a self-cleaning program. See Self-cleaning in the chapter Using the dishwasher. The dishes are not dry enough. The dishwasher is connected to a garbage disposer. Cleaning the garbage disposer connected to the dishwasher can eliminate odors. Follow the disposer manufacturer's cleaning instructions. Depending on the load, the program's drying cycle may be insufficient. Activate the Extra Dry option. The dishwasher is not fully loaded. Fully load the dishwasher. Rinse aid needs topping up or dosage is set too Top up with rinse aid or increase the rinse aid low. dosage level. See the chapter Settings. Open the door a little once the program has finished. 18 Technical information Technical data Height: 34 1/2 - 35 1/2" Width: 24 5/8" Depth: 25" 1) Weight: 163 lb (74 kg) 2) Water pressure: 4.2–140 psi Electrical connection: See serial number plate Rated power: 1) 2) See serial number plate 27 1/4" including handle. Weight can vary due to different specifications. 19 Installation instructions [''] 25 4 1/4 > 5 3/8 29 3/4 34 1/2 - 35 1/2 29 3/4 24 5/8 52 2 3/8 4 7/8 Nominal dimensions. Actual measurements may vary. Important safety instructions Transport protection for the door • Connections to electricity, water, and drainage must be performed by a qualified professional. Do not forget to remove the transport protection for the door when unpacking the dishwasher. • Always follow applicable regulations for water, drainage, and electricity. • Take care during installation! Wear protective gloves! There must always be two people! • Place a drip tray on the floor beneath the dishwasher to prevent damage from any water leaks. REMOVE • Before screwing the dishwasher into place, test the dishwasher by running the Rinse and hold program. Check that the dishwasher fills with water and drains. Also check that none of the connections leak. WARNING! Turn off the water supply when installing the dishwasher! Operating environment The plug must be disconnected or power to the outlet turned off while installing the dishwasher! Do not place this appliance (including the PEX fill hose and drain hose) where it will be hit by direct sunlight or exposed to extreme weather conditions. Do not place the outdoor dishwasher close to a swimming pool. Water splashing on the machine’s surfaces can ultimately lead to corrosion (rust). This appliance is designed to operate outdoors. It is set to operate within the ambient temperature limits between 50 °F (10 °C) and 104 °F (40 °C). These temperature limits should not be exceeded. 20 Placing the dishwasher The dishwasher is intended for freestanding installation, but can also be installed under a countertop. Adjust the height and slide the dishwasher into place Use caution when the appliance is installed or removed to reduce the likelihood of damage to the power supply cord. 5/8'' 1'' Freestanding 1 Make sure the area where the dishwasher will be installed is firm. Adjust the dishwasher's height using the four adjustable feet to level the unit. The dishwasher may lean no more than 0.2" (5 mm). 2 Lock the steel feet with the lock nuts. 3 Once the feet are properly adjusted, tighten the anti-tip feet firmly against the floor. Anti-tip feet Built-in 1 Start by measuring the height from the floor to the bottom edge of the countertop. 2 Measure the height from the floor to the top edge of the dishwasher. 3 Adjust the dishwasher's feet by turning them clockwise to raise or counterclockwise to lower the machine. 4 Verify there is an air gap of at least 1/8'' between the underside of the countertop and the top edge of the dishwasher. 5 Tighten the lock nuts (lock nut) on the rear feet. 6 Slide the dishwasher into place. • Pull the drain and supply hoses through the opening as the dishwasher is slid into place. • Check that the hoses have no kinks or sharp bends, and check that there is nothing that can damage the hoses. 7 Make any final adjustments to the front feet (the dishwasher may lean no more than 1/4'') and tighten the lock nuts. 8 Once the feet are properly adjusted, tighten the anti-tip feet firmly against the floor. 21 Drain connection Connection to water supply The high loop is necessary for proper draining. Therefore, the dishwasher has the drainage hose attached to the top back of the unit. This gives the drainage hose an automatic high loop. The drainage hose is fastened at the best high loop height. Use only the inlet hose supplied with the dishwasher. Do not re-use old or other spare hoses. The supply pipe must be fitted with a water supply valve. The water supply valve must be easily accessible, so that the water can be shut off if the dishwasher has to be moved. Once the installation is complete, turn on the water supply valve and allow the pressure to settle for a while. Check that all connections are watertight. High loop Water supply The machine can be connected to either a cold or a hot (max. 160 °F (70 °C)) water supply. The water pressure should be 4.2-140 psi. Connection to cold water supply Connect the dishwasher to the cold water supply if the building is heated using oil, electricity, or gas. The hose must always discharge at least 13 3/4'' above the bottom of the machine. Connection to hot water supply Connect the dishwasher to the hot water supply (max. 160 °F (70 °C)) if the building is heated using an energy-efficient means such as district heating, solar power, or geothermal power. Choosing a hot water connection cuts dishwashing times and reduces the dishwasher's energy consumption. NOTE! Do not exceed the permitted water supply temperature. Certain materials used in some cookware cannot withstand strong heat. See Fragile dishes in the chapter Loading the dishwasher. min. 1/2'' Electrical connection Information about the electrical connection can be found on the serial number plate. This specification must match the electricity supply. The power supply receptacle for the appliance must be installed in a cabinet or on a wall adjacent to the undercounter space in which the appliance is to be installed. Do not use an extension cord for this appliance. Connect the drain hose to, for example, the sink's water trap. The connection nipple must have an internal diameter of at least 1/2''. The water trap must be ventilated. The drain hose may be extended by a maximum of 87" (2.2 m) (the total length of the drain hose must not exceed 177" (4.5 m)). Any joins and connecting pipes must have an internal diameter of at least 1/2''. However, the drain hose should ideally be replaced with a new hose without joins. No part of the drain hose may be more than 37 3/8'' above the bottom of the dishwasher. Attach the drain hose with a hose clamp. Ensure that the drain hose has no kinks. NOTE! Do not remove the high loop attached to the back of the dishwasher! To accommodate a drain on the left side of the dishwasher, remove the drain hose and reverse the direction in the high loop bracket. The access hole for the the electrical supplie must be round and smooth and no bigger than 1 1/2'' in diameter. If the partition is metal, it needs to be covered with an edge protector. Use caution when the appliance is installed or removed to reduce the likelihood of damage to the power supply cord. Grounding Instructions This appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord fitted with an equipment grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is installed and grounded in accordance with all local codes and ordinances. WARNING! Improper connection of the equipment grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative if you are in doubt as to whether the appliance is properly grounded. Do not modify the plug provided with the appliance. If it does not fit the outlet, have an appropriate outlet installed by a qualified electrician. WARNING! Risk of electric shock. Do not use an extension cord for this appliance. Connect dishwasher cord directly to a dedicated outlet suitable for installation in damp or wet locations and protected by a Ground-Fault Circuit-Interrupter (GFCI) in accordance with local codes. If an outlet is not provided, contact a qualified electrician for proper installation. 22 Service Limited Warranty – Residential Appliances ASKO Distribution North America, LLC. (“ASKO”) warrants to the original purchaser (the “ASKO Customer”) of the ASKO product (the “ASKO Product”), who purchased the ASKO Product from a distributor, dealer, manufacturer’s representative or other seller who has been authorized by ASKO, that this ASKO Product is free of defects in materials and/or workmanship, subject to the terms and conditions set forth herein. This Limited Warranty covers parts and labor, except as set forth in this Limited Warranty. Service must be provided by an authorized ASKO service company. YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. This Limited Warranty is valid only when the ASKO Product is used in the country in which it was purchased. Proof of original purchase date is required to obtain service under this Limited Warranty. Residential ASKO Products Used Exclusively for Household/Personal Purposes: Two (2) Years limited Warranty – Any warranty service claims for residential ASKO Products must be filed with ASKO within two (2) years from date of purchase. Service will be provided during normal business hours. Residential ASKO Products Not Used Exclusively for Household/Personal Purposes or used Commercially or used in Marine, Mobile or Aeronautical Applications: One (1) Year limited Warranty – Any warranty service claims for ASKO Products not used exclusively for household and personal use, or used commercially or used in marine, mobile, or aeronautical applications must be filed with ASKO within one (1) year from date of purchase. Service will be provided during normal business hours. Items excluded from warranty This limited warranty does not cover: 1 Replacement parts or repair labor if the ASKO Product is used in a manner that is inconsistent with published user or operator instructions and/or installation instructions. 2 Service calls to correct the installation of the ASKO Product, to instruct you on how to use the ASKO Product, to replace or repair house fuses, or to correct house wiring or plumbing. Disclaimer YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. EXPRESSLY DISCLAIMED ARE ALL OTHER EXPRESS AND IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Some jurisdictions do not allow exclusion or limitations regarding warranty rights. This Limited Warranty gives you specific legal rights and you may have other rights that vary from jurisdiction to jurisdiction. Attempted repair by any person other than an authorized ASKO service company will void this Limited Warranty. Limitation of liability IN NO EVENT SHALL ASKO OR THE MANUFACTURER AND THEIR RESPECTIVE PARENTS, SUBSIDIARIES AND AFFILIATES BE LIABLE FOR CONSEQUENTIAL, INCIDENTAL, EXEMPLARY, PUNITIVE OR SPECIAL DAMAGES. IN NO EVENT SHALL ASKO OR THE MANUFACTURER AND THEIR RESPECTIVE PARENTS, SUBSIDIARIES AND AFFILIATES BE LIABLE FOR DAMAGES OTHER THAN ACTUAL DAMAGES AND IN NO EVENT FOR DAMAGES IN EXCESS OF THE PRICE PAID FOR THE ASKO PRODUCT AS TO WHICH A CLAIM IS MADE. Some jurisdictions do not allow the exclusion or limitation of incidental, consequential or other damages, so these limitations and exclusions may not apply to you. This Limited Warranty gives you specific legal rights. You also may have other rights that vary from jurisdiction to jurisdiction. Troubleshooting & ASKO Customer Care If you think you need repair service, first see the Troubleshooting section of the Use & Care Guide. If you are unable to resolve the problem after checking Troubleshooting, then additional help can be obtained by calling ASKO Customer Care at 1-800-898-1879. Read the chapter Troubleshooting before contacting the Customer Care Center. If you have encountered a problem that you cannot resolve, please contact your nearest dealer, see www.asko.com. When making contact, provide the details on the serial number plate. Include the service number (1), the article number (2), and the serial number (3). 3 Consumable items and parts, such as filters. 4 Damage resulting from accident, alteration, misuse, abuse, negligence, fire, flood, acts of God, improper use, improper installation, installation not in accordance with electrical or plumbing codes, or use of products not approved by ASKO, as well as any attempted repair by other than authorized ASKO service companies. 5 Cosmetic damage, including scratches, dents, chips or other damage to the finish of the ASKO Product, unless such damage results from defects in materials or workmanship and is reported to ASKO within 5 days from date of purchase. 6 Pickup and delivery. The ASKO Product is intended to be repaired in your home. 7 Repairs to parts or systems resulting from unauthorized modifications made to the ASKO Product. 8 Expenses for travel and transportation for product service if the ASKO Product is located in a remote area where service by an authorized ASKO service company is not available. 9 The removal and reinstallation of the ASKO Product if it is installed in an inaccessible location or is not installed in accordance with ASKO’s published installation instructions. 10 Replacement parts or repair labor on ASKO Products with original model/serial numbers that have been removed, altered or cannot be easily determined. 1 2 3 Service no. ART. NO. SERIAL NO. Service after expiration of limited warranty For information about obtaining parts and labor after expiration of this Limited Warranty or arising outside the scope of this Limited Warranty, please contact ASKO Customer Care at 1-800-898-1879. After your purchase and prior to first use of the ASKO Product, register your ASKO Product with ASKO by utilizing the address information below. Should you need further assistance as well, contact us at the address information below: ASKO Distribution North America, LLC Customer Care Center, PO Box 44848, MADISON WI 53744 23 Quick start guide Load the baskets (See page 5.) 1. Do not rinse dishes under running water before loading them in the dishwasher. Simply scrape off large food particles before loading the dishwasher. Check that the spray arms can rotate freely 2. Check also that the water supply valve is on. 3. The detergent compartment has a small compartment for prewash and a large compartment for the main wash. (See page 8.) Don't forget! Empty the coarse filter and clean the fine filter when necessary. (See page 14.) Add detergent Press and hold the main power switch until the display lights up 4. Check/Add rinse aid Top up rinse aid for optimal washing and drying results. (See page 4.) 5. Refill rinse aid indicator. Select a program, program mode, and any options (See page 9.) START Press and hold Start/Stop until the display shows "Program started, close door in 4 sec". This indicates that the dishwasher is ready to start. Close the door properly within four seconds, otherwise the dishwasher will not start. en (04-18) 7. STOP Press Start/Stop, close the door 24 www.askona.com Item No.: 706077. Rev. 02. We reserve the right to make changes. 6.