Blomberg | DWT58500SSWS | Installation instructions | Blomberg DWT58500SSWS Installation Instructions

Dishwasher
Installation Manual
DWT 25502 B
DWT 56502 SS
DWT 25502 SS
DWT 58500 B
DWT 25502 W
DWT 58500 FBI
DWT 28500 B
DWT 58500 SS
DWT 28500 SS
DWT 58500 SSWS
DWT 28500 SSWS DWT 58500 W
DWT 28500 W
DWT 59500 FBI
DWT 56502 FBI
DWT 59500 SS
To prevent accidents, which could cause serious injury or death, as well as
machine damage read these instructions before installation and / or use.
INTRODUCTION
1
1. IMPORTANT SAFETY INSTRUCTIONS
1
2. TOOLS WHICH MAY BE NEEDED
3
3. MATERIALS WHICH MAY BE NEEDED
3
4. MATERIALS SUPPLIED
4
5. DISHWASHER SPECIFICATIONS
5
6. ENCLOSURE PREPARATION
6
1.1 INSPECT THE DISHWASHER
1.2 HOW TO CONTACT US :
4.1 PARTS SUPPLIED
4.2 MANUAL BAG
4.3 DISHWASHER PARTS BAG 1
4.4 DISHWASHER PARTS BAG 2
4.5 PARTS ATTACHED TO THE REAR OF THE DISHWASHER
5.1 TECHNICAL FEATURES
2
2
4
4
4
4
4
5
6.1 ELECTRICAL PREPARATION
6.2 PREPARATION FOR INSTALLING MOUNTING BRACKETS
6.3 ADJUSTING HEIGHT
6.4 INSTALLING THE SIDE TRIM STRIPS
6.5 PREPARING THE WATER CONNECTION (A)
6.6 DRAIN PREPARATION
6.7 STEAM PROTECTION FOIL
6
6
6
7
8
9
10
7. PLACEMENT OF DISHWASHER INTO THE OPENING
11
8. INSTALLER CHECKLIST
22
9. FINAL INSTRUCTIONS
22
10. SELF HELP HINTS:
22
7.1 DRAIN HOSE CONNECTION, WATER SUPPLY & ELECTRICAL CONNECTIONS
7.2 READJUSTING FOOT LEVELS
7.3 ADJUSTING THE MOVABLE TOE KICK
7.4 INSTALLING THE OUTER DOOR
11
15
15
16
INTRODUCTION
WARNING
Please read this installation manual
and particularly the safety instructions
completely and carefully. They will save you
time and effort and help to ensure optimum
dishwasher performance.
When installing the dishwasher, follow
basic precautions, including the
following:
• The dishwasher installation must be
performed in accordance with this
installation manual. If you did not receive
an installation manual, order it by
calling 1-800-459-9848 or you may also
download it from our web site at www.
blombergappliances.com
• The dishwasher could only be converted
from cord-connected to permanently
connected by an authorized service
representative. (If needed contact your
dealer to schedule an authorized service
agent for conversion with an appropriate
conversion kit)
• Installation and repair should be
performed by a qualified installer.
Work by unqualified persons could be
dangerous and may void the warranty.
Be sure to observe all listed warnings and
cautions. Look particularly for the icons with
exclamation marks inside. The information
icon also will provide important references.
WARNING:
Indicates a potentially hazardous situation
which, if not avoided, could result in death
or serious injury.
CAUTION:
Indicates a potentially hazardous situation
which, if not avoided, may result in injury.
It may also be used to alert against unsafe
practices.
NOTICE:
Indicates a potentially hazardous situation
which, if not avoided, may result in damage
to the dishwasher, the table-ware, the
equipment or the environment.
NOTICE :
The dishwasher should be installed by
an insured licensed plumber, contractor
or trained installer. Installation performed
by persons other than this could result in
improper installation and property damage.
• Do not operate the appliance if damaged,
malfunctioning, partially disassembled or
if it has missing or broken parts.
• Also follow the safety instructions of the
user manual.
• To reduce the risk of electric shock, fire,
or injury to persons, the installer must
ensure that the dishwasher is completely
enclosed at the time of installation.
• Only connect the dishwasher to the
power supply when all installation and
plumbing work is complete.
• If the dishwasher is installed in a location
that experiences freezing temperatures
(e.g. in a vacation home, cabin, etc.),
you must drain all the water from the
dishwasher’s interior. Water system
ruptures that occur as a result of freezing
are not covered by warranty.
• Dishwasher must be secured to adjacent
1. IMPORTANT SAFETY
INSTRUCTIONS
In addition to these instructions, the
dishwasher shall be installed:
• In accordance with all local codes or, in
absence of a local code,
• In the United States, with the National
Electric Code,
• In Canada, with the Canadian Electric
Code C22.1-latest edition/Provincial and
Municipal codes and/or local codes.
NOTICE :
Read these installation instructions
completely before installing and follow
them carefully. Save these installation
instructions and pass them on to any future
user.
1
USA
•
•
•
•
•
cabinetry using the brackets provided.
Failure to do this may cause damage to
property or bodily injury.
Connect to a properly rated, protected
and sized power supply circuit to avoid
electrical overload. The dishwasher is
designed for an electrical supply of 120 V
(volts), 60 Hz (hertz), AC, connected to a
dishwasher-dedicated, properly grounded
electrical circuit with a fuse or breakers
rated for 15 amperes. Electrical supply
conductors shall be a minimum of # 16
AWG copper wire rated at 75 °C (167
°F) or higher. These requirements must
be met to prevent injury and machine
damage. Consult a qualified electrician if
in doubt.
Do not use any extension cord or
portable outlet device to connect the
dishwasher to a power supply.
Ensure that any plastic wrappings, bags,
small pieces etc. are disposed of safely
and kept out of the reach of children.
Danger of suffocation!
Remove the door to the washing
compartment when removing an old
dishwasher from service or discarding it.
Ensure that the appliance presents no
danger to children while being stored for
disposal.
Old appliances may contain materials
that can be recycled. Please contact
your local recycling authority about the
possibility of recycling these materials.
compatibility with the new dishwasher,
and replace parts as necessary.
1.1 INSPECT THE DISHWASHER
After unpacking the dishwasher and prior
to installation, thoroughly inspect the
dishwasher for possible freight or cosmetic
damage. Report any damage immediately.
NOTICE :
• Cosmetic defects must be reported within
10 days of installation.
• Do not discard any bags or items that
come with the original package until
after the entire installation has been
completed.
1.2 HOW TO CONTACT US :
You may either call our Toll Free Number
at 1-800-459-9848 or contact us via the
web site at www.blombergappliances.
com or Contact the Blomberg Distributor
for your State or Province as listed on the
Distributor Contact List provided.
NOTICE :
• The dishwasher drain hose must be
installed with a drain loop at least 28”
(710mm) off the cabinet floor; otherwise
the dishwasher may not drain properly.
• This dishwasher is intended for
residential use only, and should not be
used in commercial establishments.
• New installation - If the dishwasher is a
new installation, most of the work must
be done before the dishwasher is moved
into place.
• Replacement - If the dishwasher is
replacing another dishwasher, check
the existing dishwasher connections for
2
USA
2. TOOLS WHICH MAY BE NEEDED
3. MATERIALS WHICH MAY BE NEEDED
(Additional materials may be required to comply with local codes)
Hot Water Supply Line - Minimum 3/8” O.D. copper tubing or metal braided
dishwasher supply line.
90° elbow with 3/8” N.P.T. male threads on one leg, and sized to fit your
water supply line (copper tubing/compression fitting, or braided hose) on
the other leg.
UL listed conduit connector or strain relief.
Teflon tape or other pipe thread compound to seal plumbing connections.
Shut-off valve and fittings appropriate for hot water supply line (copper
tubing/compression fitting, or braided hose).
Silicone
Glue
3
USA
4. MATERIALS SUPPLIED
4.1 PARTS SUPPLIED
Parts for your dishwasher will come in several plastic bags.
Check your parts bags shown to make sure you have all the
parts as listed to the left.
4.2 MANUAL BAG
The dishwasher comes with a manual bag containing:
• User manual,
• Installation manual
4.3 DISHWASHER PARTS BAG 1
This dishwasher bag comes with the following parts:
a. Side Trim Strips (Left)
b. Side Trim Strips (Right)
c. Adjusting Wrench
d. Screws Ø 1/8” x 5/8” (Ø 3.5 mm x 14 mm)
e. Mounting Bracket Left
f. Mounting Bracket Right
g. Spring Clamp
h. Screw Clamp
j. Rubber Connector
k. Toe Kick Bracket - Left
l. Toe Kick Bracket – Right
m. Edge Protector
n. Clips
o. Toe Kick (toe kick without slots)
p. Toe Kick (MODEL DEPENDING)
r. Screws Ø 1/8” x 3/8” (Ø 3.9 mm x 9 mm)
s. Plastic Caps
t. Screws Ø 3/16” x 1/4” (Ø 4mm x 6mm)
z. Steam Protection Foil
4.4 DISHWASHER PARTS BAG 2
(MODEL DEPENDING)
In addition to the manual bag and the dishwasher parts bag
(dishwasher models which can accept a wooden kitchen door)
also come with a door panel installation kit which contains:
v. Screws Ø 1/8” x 5/8” (Ø 3.5mm x 14mm)
y. Screws Ø 3/16” x 13/4” (Ø 4mm x 43mm)
4.5 PARTS ATTACHED TO THE REAR OF THE
DISHWASHER
a. Side Trim Strips (Left)
b. Side Trim Strips (Right)
o. Toe Kick (toe kick without slots)
p. Toe Kick (MODEL DEPENDING)
4
USA
5. DISHWASHER SPECIFICATIONS
5.1 TECHNICAL FEATURES
Load capacity
Permissible water pressure
Electrical connection
Total power
Heater power
14 place settings
4.35 - 145 psi (0.3 - 10 bars)
120 V (volts), 12 A (amps), 60Hz (hertz)
1400 W (watts)
1100 W (watts)
NOTICE :
Because we continually strive to improve our products, we may change our specifications
and design without prior notice.
This device corresponds to the following directives:
UL 749 Household Dishwasher directive.
5
USA
6. ENCLOSURE PREPARATION
6.1 ELECTRICAL PREPARATION
WARNING
The dishwasher is designed for an electrical supply of 120 V, 60 Hz, AC, connected
to a dishwasher-dedicated, properly grounded electrical circuit with a fuse or breaker
rated for 15 amperes.
6.2 PREPARATION FOR INSTALLING MOUNTING BRACKETS
WARNING
Dishwasher must be secured to
adjacent cabinetry using the mounting
brackets provided. Failure to do this
may cause damage to property or
bodily injury.
Place the two mounting brackets into
the top corners of the dishwasher.
Fix the mounting brackets (A) to the
top corners of the dishwasher, with the
screws supplied.
Bend sides of mounting brackets (B) in
order to fix from sides (if necessary).
6.3 ADJUSTING HEIGHT
If the height of the enclosure is 337/8” to
357/8” (861 mm - 911mm) adjust supports
as shown in the figure.
Supplied (4)
6
USA
Adjust the front foot level with the adjusting
wrench to balance and raise the dishwasher to the
enclosure height.
Adjust the rear foot level with a screwdriver to
balance and raise the dishwasher to the enclosure
height.
NOTICE :
• Make sure the dishwasher is plumb and
notice dishwasher can be placed with a small
clearance under the counter top.
• Turning the screwdriver in the direction of the
black arrows will bring the dishwasher back feet
up.
• Turning the screwdriver in the direction of the
white arrows will take the dishwasher rear feet
down.
6.4 INSTALLING THE SIDE TRIM STRIPS
1. Remove the adhesive tape (Figure A).
Place the trim strips on the front edge of the side
walls (Figure B).
NOTICE :
• Make sure you use the correct trim strip since
there is a left and right side strip. The flexible
material should be facing forward (Figure B).
7
USA
6.5 PREPARING THE WATER
CONNECTION (A)
6.5.1 INSTALLING THE 90° ELBOW
FITTING (B)
CAUTION
Install an easily accessible shut-off valve
(not supplied) in the water supply line.
All solder connections must be made
before the water line is connected to the
dishwasher’s water inlet valve. Water can
also be supplied to the dishwasher by using
a flexible braided hose line.
Do not over tighten the 90° elbow. Doing
so may damage the water inlet valve and
cause a water leak.
If the water supply line is to be copper
tubing, make certain that the elbow has a
compression fitting. Apply Teflon tape or
other pipe sealant when required. Orient
the water supply connection downwards as
shown in the figure so the water line can be
easily pulled underneath or on the side of
the dishwasher.
Check with your plumbing supply sources
for the proper hose and 90° elbow and
necessary fittings for the water supply line.
This material is not supplied, and must be
purchased separately.
WARNING
Installation should be performed by a
qualified installer. Work by unqualified
persons could be dangerous and may
void the warranty.
If the dishwasher is installed in a
location that experiences freezing
temperatures (e.g. in a vacation home,
cabin etc.), you must drain all the water
from the dishwasher’s interior. Water
system ruptures that occur as a result of
freezing are not covered by warranty.
B
A
8
USA
6.6 DRAIN PREPARATION
The dishwasher drain hose may be connected to the drain plumbing in one of three ways
(Figure A, B, C).
NOTICE :
• Either one of the above methods must be used or the dishwasher will not operate
properly.
• A hose that attaches to a sink spray can burst if it is installed on the same water line as
the dishwasher. If your sink has one, it is recommended that the hose be disconnected
and the hole plugged.
• The total length of the drain hose is 763/4” (1950mm). If a hose extension is required, a
drainage hose of equal quality must be used.
• The maximum length must not exceed 157 ½” (4000mm). Otherwise, the cleaning
process is negatively influenced.
6.6.1 UNDER THE SINK DRAIN
Install a Y-branch tail pipe. (Figure A)
NOTICE :
You must add a loop at least 28” (710mm) above the floor of
the cabinet and above the drain connection in the drain hose
to prevent waste water from not draining properly, and causing
either poor washing results or a bad odor.
6.6.2 INSTALLING AN AIR GAP
If the local ordinance requires an air gap (Figure B).
NOTICE :
Check with local ordinance for type of air gap required.
6.6.3 DISPOSAL
Remove the drain connection plug before attaching the drain
hose from the dishwasher.
Every disposal has a hook up for a dishwasher; consult your
disposer manual for correct connection. (Figure C)
9
USA
6.7 STEAM PROTECTION FOIL
Steam will form inside the dishwasher during operation. At the end of the cycle, when the
dishwasher door is opened, it is required to use a steam protection foil to prevent any
steam from collecting on the underside of the counter top.
6.6.2 FITTING THE PROTECTION FOIL
Before applying the steam protection foil to the
underside of the countertop, clean the area with
a damp cloth (as shown in Figure A). Once the
area dries, apply the steam protection foil.
The steam protection
foil will be applied at the
location where the hot
steam escapes when you
first open the door (as
shown in Figure B).
CAUTION
Steam protection foil must be applied
where the steam escapes when door is
first opened. Failure to install the steam
protection foil during installation can
lead to damage to the cabinets and
countertop.
10
USA
7. PLACEMENT OF DISHWASHER INTO THE OPENING
Now place the dishwasher into the opening and get ready to connect all hoses and
electrical connections.
CAUTION
Make sure all hoses
are pulled through the
side opening of the
cabinet, no hoses are
kinked and all slack is
taken out as shown in
the above figure.
7.1 DRAIN HOSE CONNECTION, WATER SUPPLY & ELECTRICAL
CONNECTIONS
7.1.1 DRAIN HOSE CONNECTION
Connect the drain hose to the drain plumbing.
1. Use the supplied rubber connection hose and drain hose clamps to connect the
dishwasher drain hose to the plumbing drain connection.
2. Use the spring clamp to secure the rubber connection hose to the dishwasher drain
hose. Use the screw clamp to secure the rubber connection hose to the plumbing drain
connection.
Note that the marks on the
rubber connection hose
should be on the drain hose
side
11
USA
7.1.2 PREPERATION OF WATER SUPPLY
Left side water supply
connection
Before pushing the dishwasher in to the cabinet
you must place water supply hoses into the
channel of the dishwasher (Figure A). Place the
supplied clips into the channel (Figure B) so
that you can move these clips along the channel
(Figure C) and fix by pressing on (Figure D) so
that you can keep the water supply hose in the
channel.
12
USA
After installing one clip
for each side push the
dishwasher into the
cabinet (Figure E).
Note that while pushing the dishwasher into the
cabinet, water supply hose must move in the channel to
the front (Figure F).
Fix the second clip (Figure G).
13
USA
7.1.3 WATER SUPPLY CONNECTION
Water supply may be connected to the
dishwasher in one of two ways:
• With metal braided hose.
• With copper tubing.
CAUTION
• Hot water supply line: Use minimum 3/8”
O.D. copper tubing or metal braided
dishwasher supply line.
• Temperatures required for soldering and
sweating will damage the dishwasher’s
water inlet valve so if any such operation
is needed, keep the heat source
min. 77/8” (200mm) away from the
dishwasher’s water inlet valve.
• There should not be any sharp bends in
the water line that may restrict the water
flow.
• Teflon tape or pipe tread compound
must be used for sealing the connection.
Before connecting the copper water
supply line to the dishwasher, flush it with
hot water to clear any foreign material.
• Do not use any extension cord or
portable outlet device to connect the
dishwasher to a power supply.
• The power-supply receptacle for the
appliance shall be installed in a cabinet
or on a wall adjacent to the undercounter
space in which the appliance is to be
installed.
• The access hole of the supply cord to the
installation compartment must be smooth
and rounded and it must be large enough
for the attachment plug to pass through.
The longest dimension of the opening
shall not be more than 1,5” (38 mm).If the
partition is metal, it needs to be covered
with an edge protector.
• Care must be taken when the appliance
is installed or removed, to reduce the
likelihood of damage to the power-supply
cord.
7.1.4 ELECTRICAL CONNECTION
7.1.5 GROUNDING INSTRUCTIONS
This appliance must be grounded. In the
event of a malfunction or breakdown,
grounding will reduce the risk of electric
shock by providing a path of least
resistance for electric current. This
appliance is equipped with a cord having
an equipment-grounding conductor and a
grounding plug. The plug must be plugged
into an appropriate outlet that is installed
and grounded in accordance with all local
codes and ordinances. This appliance
must be connected to a grounded metal,
permanent wiring system, or an equipmentgrounding conductor must be run with the
circuit conductors and connected to the
equipment-grounding terminal or lead on
the appliance.
• Make sure the voltage and frequency
listed on the data plate correspond with
the household electrical supply. This data
must correspond to prevent injury and
machine damage. Consult a qualified
electrician if in doubt.
• Only connect the dishwasher to the
mains when all installation and plumbing
work is complete.
Improper connection of the equipmentgrounding conductor can result in a risk
of electric shock. Check with a qualified
electrician or service representative if
you are in doubt whether the appliance is
properly grounded. Do not modify the plug
provided with the appliance, if it will not fit
the outlet, have a proper outlet installed by
a qualified electrician.
NOTICE :
After connections are made turn on the
water supply to check for leaks.
WARNING
14
WARNING
USA
7.2 READJUSTING FOOT
LEVELS
Now that the dishwasher is in the
cabinet you must readjust the feet to
bring the dishwasher up to the required
height and attach it underneath the
countertop.
1. Readjust the front foot levels with
adjusting wrench to balance the
dishwasher and raise it up under the
countertop, make sure the unit is level.
2. Readjust the rear foot levels with a
screwdriver to balance the dishwasher
and raise it to the required height using
the brackets supplied.
3. Attach the dishwasher underneath
the countertop with the four screws
supplied (Ø 1/8” x 1/8” - Ø 3.5mm
x 14mm). Make sure you do not go
through the top of the countertop or
damage granite.
7.3 ADJUSTING THE MOVABLE TOE KICK
Now that you have successfully installed the dishwasher, you
need to attach the toe kick to the dishwasher. The two piece toe
kick can be adjusted to the height and depth needed for your
kitchen. Be sure to use the slotted toe kick in the front and the
other behind it. They slide into each other.
1. Insert the movable toe kick brackets into the channel (A).
2. Make sure that the plastic tab to the left of the “L” opening
on the dishwasher has not closed the channel you will push the
bracket through.
NOTICE :
Be sure to notice there is a left and a right bracket.
Adjust the toe kick brackets forward or backwards so that they
will align with the kitchen toe kick (B).
Lock the toe kick brackets as shown with the plastic tab in the
figure C by pushing the plastic tab on the dishwasher into the
teeth of the bracket (C).
3. Now attach the toe kick to the bracket with the two (Ø 3/16” x
1/4” - Ø 4mm x 6mm) screws and the caps provided as follows.
15
USA
If the enclosure height is above 331/16” (840mm)
use “o” and “p” labelled toe kicks together. Make
sure the slotted toe kick “p” is on the outside so
you can adjust height of the toe kick. Installation
should be done following the steps illustrated in the
figures A, B and C respectively.
1. Align the toe kick (o) and (p) (A).
2. Secure toe kicks to brackets with screws (t) after
adjusting the height of the slotted toe kick (p) (B).
3. Attach caps (s) as shown in the supply bags (C).
If the enclosure height is below
331/16” (840mm) use only
“o” labelled toe kick (toe kick
without slots). Installation should
be done following the steps
illustrated in the Figures A, B and
C respectively.
1.Bend tabs on toe kick (o)
inwards (A).
2. Secure toe kick to brackets
with screws (t) as shown in the
supply bags (B).
3. Attach caps (s) as shown in
the supply bags (C).
7.4 INSTALLING THE OUTER DOOR
(DWT 56502 FBI,DWT 58500 FBI,DWT 59500 FBI)
Measure the height and width of the enclosure
(Figure A) and the toe kick. Determine how big
the wooden door can be. For example if the height
is 337/8” (860mm) and if the toe kick is 315/16”
(100mm) the door can not be taller than 2915/16”
(760mm).
1. Prepare the wooden door with the mounting
brackets.
Height
: Height of the wooden door 30”
(760mm)
Width
: 23 ¼” to 23 ½” (592mm 595mm)
Thickness
: ¾ “ (19mm)
16
USA
2. To take the plastic bracket out, remove the
screws on it. Screws will be used in 5th step
again. (Figure B).
3. Mark the wooden door as shown
in the drawing (Figure C).
4. Place the plastic mounting brackets over the
marked holes and the side tabs must be flush
with the edge of the wooden door (Figure D).
17
USA
5. Attach the two mounting brackets to the wooden
door with 4 screws (Ø 1/8” x 5/8” (Ø 3.5mm x 14mm)
(Figure A).
6. Mount the wooden door onto the dishwasher
with the plastic mounting brackets which you have
attached (Figure B).
7. Open the door and remove the two caps and
two screws inside the door at position 1 and 4
(Figure C).
18
USA
8. Using the four screws Ø 3/16” x 111/16” (Ø
4mm x 43mm) provided, attach the wooden door
to the dishwasher at position 1 and 4 (Figure A).
9. Check the position of the wooden door and
make sure it is aligned properly (Figure B).
10. Tighten the screws in position 1 and 4
completely after the final alignment (Figure C).
19
USA
11. Check whether the bottom
of the door hits the toe kick of
the kitchen cabinet (A).
11.1. If the door hits the toe
kick cut the necessary section
out of the toe kick (B).
11.2. Apply silicon or sealant
to the cut edge of the kitchen
cabinet toe kick or paint so it
does not absorb moisture.
ADJUSTING DOOR TENSION WITH CUSTOM WOODEN DOOR
(DWT 56502 FBI,DWT 58500 FBI,DWT 59500 FBI)
Check the door tension of the
dishwasher: If the door closes too
quickly or if the door falls open,
the spring tension needs to be
adjusted.
The adjustment screws can
be found on the front of the
dishwasher after you open the
door (see drawing).
Adjust the spring tension by
turning the screw to the right for
more weight and to the left for
less weight (Figure C).
20
USA
NOTICE :
If you have a European kitchen or want to install a wooden toe kick to match your kitchen,
please refer to one of the two drawings given below. Follow the same instructions on the
brackets as for the removable toe kick.
Installation should be done following the steps illustrated in the figures A, B, C, D respectively.
See also page 15
See also page 20
NOTICE :
The installer is responsible for the dishwasher installation. Incorrect installation is not
covered by the warranty.
21
USA
8. INSTALLER CHECKLIST
Your installer must have completed and
checked the following:
• The dishwasher is square and level.
• The dishwasher is fastened securely to
the cabinetry.
• The dishwasher door opens and closes
freely. The dishwasher door must close
without hitting any cabinetry or counter
top.
• The inlet water supply is turned on and
checked for leaks.
• The drain hose has been connected and
checked for leaks. There must be no
kinks or obstructions in the drain hose.
• The drain hose must be installed with a
28" (710mm) high drain loop for drain
hook-ups without any air removed.
• If the dishwasher drain is hooked up to a
garbage disposal, the drain hopper plug
must be removed.
• The spray arms are free and rotate freely.
• The rinse cycle has been run.
• The water level will be below the
filter screen after the end of the wash
program. It is normal to find some water
in the drain filter area.
9. FINAL INSTRUCTIONS
1. Press the On/Off button to turn the
dishwasher on.
2. Power indicator light comes on.
3. Use the Program Select button to choose
a washing program.
4. Start the program with the Start/Pause/
Cancel button.
5. Run the dishwasher through one
complete cycle. When the wash cycle is
completed, use the On/Off button to turn
the dishwasher off.
10. SELF HELP HINTS:
The screen does not come on:
• Check to make sure the breaker to the
dishwasher is in the on position.
• Check to make sure that the Supply cord
is plugged.
No Water is coming into the dishwasher:
• Check to make sure the hot water shutoff is in the ON position.
Water does not drain:
• Make sure drain hose is not kinked or
comes out of air gap next to the sink.
• Remove drain hose from disposal making
sure plug is removed.
NOTICE :
• If your dishwasher is not operating
properly after following these steps:
Contact your dealer to schedule an
authorized service agent to inspect your
new dishwasher for any function related
failure.
• The manufacturer warranty does not
cover installation, conversion or customer
education service visits.
You will find the model and serial number
information on the label located on the
right-hand side of the inner door of your
dishwasher, as shown above.
NOTICE :
Please make a copy of your invoice and
keep it with this manual and register your
dishwasher on-line.
15 0575 0100_AA Installation Manual_USA/ 03-03-16.(10:05)
22
USA
www.blomberginternational.com
info@blomberginternational.com
Download PDF

advertising