Frigidaire | FDB2410HIB | Wiring Diagram All Languages | Frigidaire FDB2410HIB Wiring Diagram All Languages

Frigidaire FDB2410HIB Wiring Diagram All Languages
Product Specifications
Pump Assembly
The pump assembly is driven by a synchronous
motor. The motor drives a pump which supplies
100 percent filtered water
Draining is accomplished by using a small
separate synchronous drain pump mounted to
the side of the sump. The drain pump is
connected to the main pump by a small rubber
hose. The drain check valve is located at the
discharge end of the drain pump. The drain hose
is attached by a clamp to the discharge end of
the drain pump.
The drain hose must have a loop at a minimum Electrical
height of 32 inches in order to insure proper
Rating ................................... 120 Volts, 60Hz
drainage.
Separate Circuit..15 amp min.- 20 amp max.
Motor (Amps) ................................... 0.6 - 0.9
Heater Wattage .......................... 475 - 630W
Total Amps (load rated) .......................... 7.0
TempAssure .............................. 135°F ±5°F
(60°C±3°C) [with outer door in place]
TempBoost ................................ 140°F ±5°F
Heated Wash/Heated Rinse
Hi-Limit Thermostat ............... 200°F (93°C)
Water Supply
Suggested minimum incoming water
temperature ............................ 120°F (49°C)
Pressure (PSI) min./max. .................. 20/120
Connection (NPT) ..................................... 3/8"
Consumption (Normal Cycle) ......................
.......................................... 5.2 - 5.6 U.S. gal
Water valve flow rate (U.S. GPM) ............ 0.9
Water recirculation rate (U.S. GPM) ..............
................................................. approx. 5.28
Water fill time ................................... 36 sec.
Trouble Shooting Tips
Personal Injury Hazard
Always disconnect the dishwasher from the electrical power source before adjusting or
replacing components.
Symptom
Check the Following
Remedy
Dishwasher will not operate when
turned on.
1. Fuse (blown or tripped).
2. 120 VAC supply wiring connection
faulty.
3. Electronic control board defective.
4. No 12 VAC power to control.
5. Motor (inoperative).
6. Door switch (open contacts).
7. Door latch not making contact with
door switch.
8. Touch pad circuit defective.
9. No indicator lamps illuminate when
START or OPTIONS are pressed.
1. Replace fuse or reset breaker.
2. Repair or replace wire fasteners at
dishwasher junction box.
3. Replace control board.
4. Replace control board.
5. Replace motor/impeller assembly.
6. Replace latch assembly.
7. Replace latch assembly.
Motor hums but will not start or run.
1. Motor (bad bearings).
2. Motor stuck due to prolonged
non-use.
1. Replace motor assembly.
2. Rotate motor impeller.
Motor trips out on internal thermal
overload protector.
1. Improper voltage.
2. Motor windings shorted.
3. Glass or foreign items in pump.
1. Check voltage.
2. Replace motor/impeller assembly.
3. Clean and clear blockage.
Dishwasher runs but will not heat.
1.
2.
3.
4.
Heater element (open).
Electronic control board defective.
Wiring or terminal defective.
Hi-Limit thermostat defective.
1.
2.
3.
4.
Replace heater element.
Replace control board.
Repair or replace.
Replace thermostat.
Detergent cover will not latch or
open.
1.
2.
3.
4.
5.
Latch mechanism defective.
Electronic control board defective.
Wiring or terminal defective.
Broken spring(s).
Defective actuator.
1.
2.
3.
4.
5.
Replace dispenser.
Replace control board.
Repair or replace.
Replace dispenser.
Replace dispenser.
Dishwasher will not pump out.
1.
2.
3.
4.
5.
6.
Drain restricted.
Electronic control board defective.
Defective drain pump.
Blocked impeller.
Open windings.
Wiring or terminal defective.
1.
2.
3.
4.
5.
6.
Clear restrictions.
Replace control board.
Replace pump.
Check for blockage, clear.
Replace pump assembly.
Repair or replace.
Dishwasher will not fill with water.
1. Water supply turned off.
2. Defective water inlet fill valve.
3. Check fill valve screen for
obstructions.
4. Defective float switch.
5. Electronic control board defective.
6. Wiring or terminal defective.
7. Pressure Switch Stuck.
1. Turn water supply on.
2. Replace water inlet fill valve.
3. Disassemble and clean screen.
1. Drain hose (high) loop too low.
1. Repair to proper 32-inch minimum
height.
2. Install air gap at counter top.
Heater
Refer to the cycle chart on the reverse side to Voltage checks of the heater should be made in
determine when the heater is on during the the dry portion of the service test mode.
wash cycle. The heater cycles ON and OFF for
brief periods during the drying cycle.
Standard Dry Air Flow
The heated, moist air leaving the dishwasher
through the console vent causes drier air to be
drawn into the unit by way of intake vents located
at the bottom of the door.
The water on the dishes is evaporated into drier
air and the venting process continues. The
heating element is turned ON and OFF during the
entire drying cycle.
Detergent and Rinse Aid Dispenser
The detergent and rinse aid dispenser is a one
piece component consisting of a molded
detergent cup and a built-in rinse aid dispenser.
The detergent cup has a spring loaded cover
and the rinse aid dispenser has a removable
cover.
Liquid rinse aid is added to the dispenser up to
the fill line indicator. The amount of rinse aid
released can be adjusted by turning the arrow
indicator from one, being the least amount, to
four, being the greatest amount.
8. Replace console assembly.
9. Replace console assembly.
To replace dispenser:
•
•
•
•
•
•
•
shut off electricity to dishwasher,
remove outer door panel assembly,
disconnect wiring to the actuator,
remove the six screws,
remove the dispenser,
replace and reinstall screws,
rewire actuator.
Dishwasher water siphons out.
2. Drain line connected to a floor drain
not vented.
Detergent left in dispenser.
1. Detergent allowed to stand too long in
dispenser.
2. Dispenser wet when detergent was
added.
3. Detergent cover held closed or blocked
by large dishes.
4. Improper incoming water
temperature to properly dissolve
detergent.
5. See "Detergent cover will not open."
4.
5.
6.
7.
Repair or replace.
Replace control board.
Repair or replace.
Repair or replace.
1. Instruct customer/user.
2. Instruct customer/user.
3. Instruct customer/user on proper
loading of dishes.
4. Incoming water temperature of
120°F is required to properly
dissolve dishwashing detergents.
020905
Outputs
LED
Cycles
Cycle Selection Options
Pots and Pans
Normal
China Crystal
Energy Saver
Rinse and Hold
Washing
Drying
Clean
PRE-WASH PRE-WASH
2
1
Time in Minutes
8 MIN.
8 MIN.
Water Valve
Pump Motor
Drain Motor
Heater
Dispensers
PREWASH 3
8 MIN.
PREWASH 4
8 MIN.
MAIN WASH 5
35 MIN.
WATER HEAT DELAY
RINSE 6
8 MIN.
RINSE 7
8 MIN.
DRY (HOT OR COOL)
19.5 MIN
WATER HEAT DELAY
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising