Blomberg | DWT56502SS | User manual | Blomberg DWT56502SS User Manual

Dishwasher
User manual
DWT 56502 FBI
DWT 56502 SS
Dishwasher
User manual
DWT 56502 FBI
DWT 56502 SS
To prevent accidents, which could cause serious injury or death, as well
as machine damage read these instructions before installation and / or
use.
CONTENTS
1. IMPORTANT SAFETY INSTRUCTIONS
2. INSTALLATION
3. GETTING TO KNOW YOUR DISHWASHER
4. LOADING THE DISHWASHER
1
4
5
6
4.1 UPPER RACK
4.2 LOWER RACK
4.3 PROPER AND IMPROPER LOADING OF DISHWARE
9
11
15
5. WHAT SHOULD NOT BE WASHED IN YOUR DISHWASHER
6. OPERATING THE PRODUCT
16
17
6.9 RINSE AID INDICATOR ( )
6.10 END OF PROGRAMME
6.11 WATER CUT-OFF WARNING
6.12 OVERFLOWING WARNING
23
23
24
24
7. DETERGENT & RINSE AID DISPENSER
25
8. SETTING THE WATER SOFTENER
28
9. FILLING THE DISHWASHER SALT DISPENSER
10. CARE AND MAINTENANCE
29
30
6.1 KEYS
6.2 PREPARING THE MACHINE
6.3 PROGRAMME SELECTION
6.4 AUXILIARY FUNCTIONS
6.5 SCHEDULING THE WASHING TIME
6.6 STARTING THE PROGRAMME
6.7 CANCELLING THE PROGRAMME
6.8 SALT INDICATOR (
)
7.1 FILLING THE DETERGENT DISPENSER
7.2 FILLING RINSE AID DISPENSER
7.3 SET THE DOSE OF RINSE AID
WATER HARDNESS & REGENERATION SETTINGS
10.1 CARING FOR YOUR DISHWASHER EXTERIOR
10.2 CARING FOR YOUR DISHWASHER INTERIOR
10.3 CLEANING THE FILTERS
10.4 CLEANING THE HOSE FILTER
10.5 CLEANING THE IMPELLERS
17
18
18
20
22
22
23
23
25
26
27
28
31
31
32
33
33
11. TROUBLESHOOTING
35
12. TECHNICAL FEATURES
39
13. WARRANTY STATEMENT FOR THE BLOMBERG DISHWASHERS 40
14. HOW TO GET SERVICE
42
1. IMPORTANT SAFETY
INSTRUCTIONS
INTRODUCTION
Please read this user manual and
particularly the safety instructions
completely and carefully. They will save
you time and effort and help to ensure
optimum dishwasher performance.
A
Be sure to observe all listed warnings
and cautions. Look particularly for the
icons with exclamation marks inside.
The information icon will also provide
important references.
WARNING:Indicates a
potentially hazardous
situation which, if not
avoided, could result in death
or serious injury.
A
A
C
CAUTION :Indicates a
potentially hazardous
situation which, if not
avoided, may result in injury.
It may also be used to alert
against unsafe practices.
••
••
••
NOTICE: Indicates a
potentially hazardous
situation which, if not
avoided, may result
in damage to the
dishwasher, the tableware, the equipment or the
environment.
••
••
••
••
••
1
USA
WARNING:When using the
dishwasher, follow basic
precautions, including the
following:
Read all instructions before
using the dishwasher! Save
these operating instructions
and pass them on to any
future user.
Use the dishwasher only for its
intended purpose as described in
this user manual. This appliance
is intended for normal household
use only.
The manufacturer disclaims
responsibility for damage or
injury caused by improper use
of this appliance.
The information in this user
manual must be followed to
minimize the risk of fire or
explosion and to prevent property
damage, personal injury or loss of
life.
Do not operate your dishwasher
unless all the enclosure panels are
properly in place.
Do not tamper with the controls.
Do not abuse, sit on, stand in or
on the door or dish rack of the
dishwasher.
The cup racks are designed to
support cups, glasses and kitchen
utensils. When the cup racks are
in the dishwasher do not lean on
or use the cup racks to support
your body weight.
To reduce the risk of injury, do not
allow children to play in, on or near
the dishwasher.
••
••
••
••
••
••
••
Use only detergents or rinse
aids recommended for use in a
household dishwasher and keep
them in a dry place out of the
reach of children. Check that the
detergent dispenser is empty
after the completion of each wash
program.
Dishwasher detergents are
alkaline. They can be dangerous
if inhaled or swallowed. Avoid
contact with skin and eyes and
keep children and infirm persons
away from the dishwasher when
the door is opened. Consult a
doctor immediately if detergent
has been swallowed or inhaled.
Do not drink water from the
dishwasher! Harmful residues
could be present.
Under certain conditions hydrogen
gas may be produced in a hot
water heater system that has not
been used for two weeks or more.
Hydrogen gas is explosive. If the
hot water system has not been
used for such period, before using
the dishwasher turn on all hot
water taps and let the water flow
from each for several minutes.
This will release any accumulated
hydrogen gas. As gas is
flammable, do not smoke or use
an open flame during this time.
Do not store or use flammable
liquids or vapors in the area of the
dishwasher.
When loading items to be washed,
position sharp items so that they
are not likely to damage the door
seal and load sharp knives with
the handles up to reduce the risk
of cut-type injuries.
Do not wash plastic items unless
they are marked “dishwasher
safe” or the equivalent. For plastic
items not so marked, check the
••
••
••
••
••
••
••
2
USA
manufacturer’s recommendations.
If a malfunction occurs, switch
off the appliance and turn off the
water supply to the dishwasher.
Please do not attempt to carry the
dishwasher by yourself in order
to avoid potential injuries. Two or
more people are needed to move
a dishwasher.
Before cleaning or carrying out
maintenance, switch off the
appliance, disconnect the power
plug and turn off the water supply.
Repairs and technical
modifications must be carried
out exclusively by a qualified
technician.
If the dishwasher is not in use for
an extended period of time (i.e.
vacation home), we recommend
you check that the baskets are
empty, leave the inside of the
dishwasher clean, leave the
door cracked open to allow air
to circulate and turn off both the
power and water supply to the
dishwasher.
This appliance must be grounded.
In the event of a malfunction
or breakdown, grounding will
reduce the risk of electric shock
by providing a path of least
resistance for electric current. This
appliance is equipped with a cord
having an equipment-grounding
conductor and a grounding plug.
The plug must be plugged into an
appropriate outlet that is installed
and grounded in accordance with
all local codes and ordinances.
Potential hazards exist if any
equipment uses electricity, water
and moving parts.
••
••
••
••
••
••
••
••
This appliance must be connected
to a grounded metal, permanent
wiring system, or an equipmentgrounding conductor must be
run with the circuit conductors
and connected to the equipmentgrounding terminal or lead on the
appliance.
This appliance produces ozone
within the washing compartment
during normal operation. Longterm exposure to ozone or
exposure at elevated levels may
result in respiratory problems,
especially for the infirmed, elderly
and children.
It is the legal responsibility
of parents/legal guardians to
supervise or instruct concerning
use of the machine when the
children become old enough to
operate.
Do not leave the door open in
order not to cause a tripping
hazard.
Remove the door to the washing
compartment when removing
an old dishwasher from service
or discarding it. Ensure that the
appliance presents no danger to
children while being stored for
disposal.
Remove the door lock or door of
the washing compartment before
disposing dishwasher so that
children or small animals can not
trapped inside.
Old appliances may contain
materials that can be recycled.
Please contact your local recycling
authority about the possibility of
recycling these materials.
Please check the water supply
line periodically. It is susceptible
to breakage. It becomes less
flexible as time goes by.Replace
it immediately when it is torn, cut,
••
swollen or there is water leakage.
Please keep the dishwasher
package out of the reach of
children after unpacking it.
WARNING:If your
dishwasher is equipped with
internal illumination, lamp
should only be replaced by
the Authorised Service Agent
in case of failures that may
occur on the lamp.
A
A
A
WARNING:Improper
connection of the equipmentgrounding conductor can
result in a risk of electric
shock. Check with a qualified
electrician or service
representative if you are in
doubt whether the appliance
is properly grounded. Do not
modify the plug provided with
the appliance, if it will not
fit the outlet, have a proper
outlet installed by a qualified
electrician.
WARNING:Warning:
This product may contain
chemicals known to the state
of California to cause cancer
or birth defects or other
reproductive harm.
SAVE THESE INSTRUCTIONS
3
USA
2. INSTALLATION
A
••
WARNING:When installing
the dishwasher, follow basic
precautions, including the
following:
The dishwasher installation must be
performed in accordance with the
installation manual. If you did not
receive an installation manual order it
by calling 1-800-459-9848 or you may
also download it from our web site at
www.blombergappliances.com
•• Please check the standarts and
local codes for placement of
machine.
•• Installation, maintenance and
repair should be performed by
a qualified installer. Work by
unqualified persons could be
dangerous and may void the
warranty.
•• Do not operate the appliance if
damaged, malfunctioning, partially
disassembled or if it has missing
or broken parts.
•• Before installation or service,
disconnect the power supply to the
work area by unplugging the unit,
“tripping” the circuit breaker or
removing the fuse.
•• Only connect the dishwasher
to the power supply when all
installation and plumbing work is
complete.
•• Never connect the ground wire
to gas lines, or hot water pipes,
plumbing lines.
•• Do not install or store the
dishwasher where it can be
exposed to below freezing
temperatures or exposed to
weather.
•• Dishwasher must be secured
to adjacent cabinetry using the
brackets provided. Failure to
do this may cause damage to
4
••
property or bodily injury.
Connect to a properly rated,
protected and sized power supply
circuit to avoid electrical overload.
The dishwasher is designed for an
electrical supply of 120 V (volts),
60 Hz (hertz), AC, connected to
a dishwasher-dedicated, properly
grounded electrical circuit with
a fuse or breakers rated for
15 amperes. Electrical supply
conductors shall be a minimum
of # 16 AWG copper wire rated
at 75 °C (167 °F) or higher.
These requirements must be met
to prevent injury and machine
damage. Consult a qualified
electrician if in doubt.
Do not use any extension cord or
portable outlet device to connect
the dishwasher to a power supply.
WARNING:Danger of
suffocation! Ensure that
any plastic wrappings,
bags, small pieces etc. are
disposed of safely and kept
out of the reach of children.
A
USA
3. GETTING TO KNOW YOUR DISHWASHER
1. Upper rack
2. Upper spray arm
3. Salt container (MODEL DEPENDING)
4. Cutlery basket
5. Detergent dispenser
6. Door
7. Control panel
8. Guiding track for the upper rack
9. Lower spray arm
10. Filters
11. Lower rack
12. Model and Serial Tag
13. Turbo fan heat drying system (MODEL DEPENDING)
14. Removable 3rd basket (MODEL DEPENDING)
15. Additional upper spray arm (MODEL DEPENDING)
5
USA
13
Lower rack (MODEL DEPENDING)
4. LOADING THE
DISHWASHER
1.
Pull the handle to open the door.
If the door is opened during
operation, the dishwasher will stop
running. Once the door is closed
the program will continue.
Upper rack (MODEL DEPENDING)
Bottom rack load pattern for 12 place
settings according to the AHAM DW-1
Standards
Upper rack (MODEL DEPENDING)
Top rack load pattern for 12 place
settings according to the AHAM DW-1
Standards
CAUTION:Hot steam can
escape! Danger of serious
burns or other injury.
A
2.
3.
Remove coarse food leftovers
from tableware.
Now you can load the dishwasher.
International Loading Pattern – Top
rack (14 place settings)
CAUTION:Hot steam can
escape! Danger of serious
burns or other injury.
A
2.
3.
6
USA
Remove coarse food leftovers
from tableware.
Now you can load the dishwasher.
Lower rack (MODEL DEPENDING)
3.
Now you can load the dishwasher.
Lower rack (MODEL DEPENDING)
International Loading Pattern – Bottom
rack (14 place settings)
Additional Loading Pattern – Bottom
rack (10 place settings)
CAUTION:Large knives and
other utensils with sharp tips
and edges must be placed
horizontally into the upper
rack due to risk of injury.
Other smaller knives and
sharp utensils should be
placed with sharp side down
in the cutlery basket.
A
Upper rack (MODEL DEPENDING)
A
Additional Loading Pattern – Top rack
(10 place settings)
CAUTION:Hot steam can
escape! Danger of serious
burns or other injury.
A
2.
Remove coarse food leftovers
from tableware.
7
USA
CAUTION:Use extreme
caution when removing
knives and other sharp
utensils from the dishwasher.
These items may have
shifted position during the
wash program, and may be
wet or slippery.
A
C
CAUTION:The cup racks are
designed to support cups,
glasses and kitchen utensils.
When the cup racks are in
the dishwasher do not lean
on or use the cup racks to
support your body weight.
4.1 UPPER RACK
Load the upper rack with dessert
plates, cups, glasses etc.
NOTICE: 3rd basket should
be removed out of the
dishwasher during the tests
according to AHAM DW-1.
••Your dishwasher holds a maximum of
12 place settings.
••Place all containers such as cups,
glasses and pots into the dishwasher
with the opening facing downwards
(so that no water can collect).
••Small and light items can go into the
upper rack.
••Long and narrow items are placed in
the middle of the racks.
••Place all large and very dirty items in
the lower rack.
••Dishes and cutlery should not be
placed above each other.
••Glasses should not touch each other.
••The movement of the spray arms
must not be hindered.
••Do not overload your dishwasher
and pay attention to manufacturer
instructions regarding dishes which
are appropriate for use in for a
dishwasher. Only with suitable dishes
(mentioned in section 5) will you
obtain optimal washing results with a
sensible use of energy.
8
ADJUSTABLE SHELVES (MODEL
DEPENDING)
Depending on the size of the glasses
and cups, the shelf height setting may
be adjusted.
1. Fold the shelf upwards A.
2. Positioning at the desired height B.
3. Fold the shelf again downwards C.
USA
COLLAPSIBLE UPPER BASKET
TINES
(MODEL DEPENDING)
There are foldable tines on the upper
basket of the machine that you can lay
down when you need larger space for
big dishes. On your upper basket there
are two types of laying tines namely,
fully laid system (A) and gradually laid
system (B). To bring the foldable tines
into horizontal position, push the tines
in the direction of the arrow by holding
from the middle. Place your larger
dishes into the area created. To bring
the tines back to vertical position, just
lift them up. Foldable tines will then
snap in the latch again.
C
COLLAPSABLE UPPER BASKET
TINES
(MODEL DEPENDING)
Upper basket of the machine is
equipped with wires with gradual
folding system (A) that you can lay
down when you need a larger space
for large dishes.
To bring the collapsible wires into
horizontal position, grab the wire from
mid position and push them in the
directions of arrows. Place your larger
dishes into the area created. To bring
the wires back to vertical position, just
lift them up. Collapsible wires will click
into the latch again.
C
NOTICE: Bringing the
wires to the horizontal
position by holding them
from the tips may cause
them to bend. Therefore, it
will be appropriate to bring
the wires in the middle to
horizontal or vertical position
by holding them from their
stems and pushing in the
direction of arrow.
9
USA
NOTICE: Bringing the wires
to the horizontal position
by holding them from the
tips may cause them to
bend. Therefore, it will be
appropriate to bring the wires
in the middle to horizontal or
vertical position by holding
them from their stems and
pushing in the direction of
arrow.
FOLDING TINES
(MODEL DEPENDING)
There are “folding tines” in the upper
rack to allow you more space to
accommodate glasses or cups.
Simply pull in the first front folding tine,
move it to left A and right B to place in
another positon. When you need, take
the tines down until the tines fall down.
LOWER UPPER RACK
1. To lower the upper rack, hold and
press in the rack lever on one side and carefully lower the rack
without releasing the lever B.
VARIABLE HEIGHT SETTING
(MODEL DEPENDING)
The upper rack is equipped with a
lifting mechanism which enables you
to change the height of the rack even if
it is fully loaded, and without having to
remove it from the dishwasher.
LIFT UPPER RACK
1. To lift the upper rack to a higher
position, hold it on one side and
carefully pull it upwards A.
2. To lift the opposite side of the rack,
hold it and pull it upwards in the
same manner.
10
2.
Repeat the procedure with the
lever on the opposite side of the
rack.
C
USA
NOTICE: Make sure that
both levers catch in the same
height position.
HEIGHT SETTING
(MODEL DEPENDING)
In certain models, the height setting of
the upper rack may be changed using
the wheels which are present at two
height levels.
CAUTION:Make sure that
the rack is empty. Changing
the height setting while the
rack contains tableware
could cause the contents to
dislodge, causing personal
injury or damage to the
tableware.
A
4.
Push the latches back into the
correct position.
4.2 LOWER RACK
1.
Release the latches on both the
right and left tracks of the upper
rack by turning them to the outside
A.
2.
Pull out the rack completely B.
3.
Place the rack into the tracks
again at the desired height C.
11
Use the lower rack for plates, bowls,
pots etc.
USA
FOUR FOLDING PLATE SUPPORT
TINES (MODEL DEPENDING)
There are 4 separate “folding plate
support tines” in the lower rack of
your dishwasher designed to allow
you more space to accommodate
saucepans, pots and large bowls in the
lower rack. You can either fold each
section (1, 2, 3, 4). individually or, all at
once, to create a large empty space.
COLLAPSABLE LOWER BASKET
WIRES 4 PIECES-(MODEL
DEPENDING)
The four piece foldable wires located
at the lower basket of the machine
are designed for an easier placement
of large pieces such as pans, bowls,
etc. (1, 2, 3, 4). You can create larger
spaces by folding each wire individually
or all of them at once. Lay the foldable
wires down by pressing on the latch
(A).
Simply press the handgrips A and fold
them down. Pull tines up to fold them
up again.
12
USA
SILVERWARE BASKET
(MODEL DEPENDING)
Silverware basket is designed to wash
your dishes such as knife, fork, spoon,
etc. in a cleaner manner.
Since the cutlery basket can be moved
(A, B), you can create a wider space
while placing your dishes to the lower
basket and free up space for your
dishes in different sizes.
To bring the collapsible wires into
horizontal position, grab the wire from
mid position and push them in the
directions of arrows (B) To bring the
wires back to vertical position, just lift
them up. Collapsible wires will click into
the latch again.
C
NOTICE: When finished, test
to ensure that the spray arm
can still move freely.
C
COLLAPSABLE LOWER BASKET
WIRES 6 PIECES-(MODEL
DEPENDING)
The foldable wires (A) located at
the lower basket of the machine are
designed for an easier placement of
large pieces such as pans, bowls,
etc. You can create larger spaces by
folding each wire individually or all
them at once.
13
USA
NOTICE: Bringing the wires
to the horizontal position
byholding them from the
tips may cause them to
bend. Therefore, it will be
appropriate to bring the wires
in the middle to horizontal or
vertical position by holding
them from their stems and
pushing in the direction of
arrow..
UPPER CUTLERY BASKET
(MODEL DEPENDING)
The upper cutlery basket is designed
for small dishes, or long items that
cannot fit into the lower cutlery basket.
After taking out the basket by lifting it
up, remove the carrier part from the
rails by pulling it towards yourself (C).
Thanks to the easy take-out-from-themachine feature, it allows taking out
the dishes from the machine together
with the basket after they are washed
(A). Since it can fit into all standard
size drawers, it does not require the
dishes to be removed from the basket
and placed into the kitchen drawers or
shelves.
Replace the rail lids and push them
back to seat them into their places.
Turn the rails inside the machine
sideways to seat them properly in their
places (D).
If you don’t want to use the upper
cutlery basket, pull it back to yourself to
remove it from the machine, rotate the
rail lids towards outside and pull them
towards yourself to take them out (B).
14
In order to replace the upper cutlery
basket into its place again, repeat the
same process in reverse order.
USA
4.3 PROPER AND IMPROPER LOADING OF DISHWARE
6 4 4
3 2
3
1: Salad Fork
2: Teaspoon
3: Dinner fork
4: Knife-solid handle
5: Serving spoon
6: Serving fork
2
1
1
1
1
2
4 4
4
3
3
3
2
4
3
2 2
2 2
2
2 1 1
1 2
2
2 1
1 2
2 1 1
2
2 1
2
2 2
2 2
3 2 3
5
3
4 4 4
3 2 3
3
5
4 4 4
Sliding Cutlery Basket load pattern for 12
place settings according to the AHAM DW-1
Standards
••Place all large and very dirty items in the lower rack.
••Place all containers such as cups, glasses and pots into the dishwasher with
the opening facing downwards (so that no water can collect).
••The movement of the spray arms must not be hindered.
••Do not overload your dishwasher. Dishes and cutlery should not be placed
above each other. Glasses should not touch.
••Only with suitable dishes (mentioned in section 5) will you obtain optimal
washing results with a sensible use of energy.
incorrect
incorrect
incorrect
15
USA
incorrect
5. WHAT SHOULD NOT
BE WASHED IN YOUR
DISHWASHER
••
••
••
••
••
••
••
••
••
Rust-sensitive steel parts like iron
and cast iron that can rust and
stain other utensils and damage
the interior stainless steel liner
of the dishwasher and void the
warranty. Do not wash copper,
brass, pewter, bronze or tin.
Cutlery with wooden or horn
handles and cutlery with motherof-pearl or porcelain handles will
deteriorate over time if put in the
dishwasher.
Plastics may lose their shape
or color with hot water, please
follow the instructions of plastic
manufacturers. Be sure that plastic
items are marked “dishwasher
safe”.
Glued dishes or cutlery are not
suitable for machine washing
since certain adhesives may get
soft or dissolve with hot water.
Aluminum may fade over time.
Minerals in water and detergent
may cause the aluminum to
darken or spot.
Sterling silver articles should not
be washed in the dishwasher
because they tend to discolor
and become dull by dishwasher
detergent.
Silverware and stainless steel
items should not be in contact with
each other. Mixing these items can
cause staining. Remove and hand
dry these items immediately when
the program ends.
Decorated glasses, porcelain, fine
china and china with gold rims
are sensitive to machine washing.
They may lose their patterns and
colors over time.
16
••
••
••
Crystal and very fine glassware
may become opaque (etch) losing
their shine over time. You may
prefer to wash them by hand.
Do not wash sponges or dish
cloths in dishwasher.
Do not wash art and craft articles
in dishwasher.
Disposable plastics and
disposable aluminum cannot
withstand high temperatures; do
not wash them in the dishwasher.
CAUTION :If in doubt,
wash by hand or follow
the instructions from the
manufacturer of utensils,
dishes, glasses or pots and
pans.
Do not wash items soiled
with cigarette ash, candle
wax, varnish, paints or
chemicals since they can
damage your dishwasher.
A
C
NOTICE: We recommend
when buying new dishware,
try to choose ones that are
suitable for machine washing
(marked as dishwasher
safe).
CARING FOR YOUR TABLE-WARE
The combination of high temperatures
and dishwasher detergent may cause
damage to some items if they are
washed in the dishwasher. Remember,
if there is any doubt about any aspect
concerning items to be washed in the
dishwasher, follow the instructions from
the manufacturer of the items, or wash
the items by hand.
USA
6. OPERATING THE PRODUCT
C
NOTICE: If you do not perform any operation after switching on the
machine, it will be automatically switched off within 5 seconds.
1
2
Cancel 3”
3
4
5
6
7
8
3
F1
F2
9
F3
F4
13 12
1. On/Off key
2. Programme Selection / Programme
Cancel (3 seconds) key
3. Function keys & indicators
F1 Half Load Function
F2 Sanitize Function
F3 Extra Rinse function
F4 Rapid Clean
4. Programme indicator
5. Salt indicator (MODEL
DEPENDING)
11
10
6. Not in use
7. Start / Cancel indicator
8. Time Delay / Programme Time
indicator
9. Time Delay key
10. Time Delay indicator
11. End of Programme indicator
12. Sanitized indicator
13. Rinse Aid indicator
6.1 KEYS
On/Off key
When you press On / Off key, indicator lights illuminate on the display for ON
position. The lights turn off in OFF position.
Programme Selection / Programme Cancel key
Press this key until the desired programme appears in the programme indicator.
To cancel the running programme open the door of the product. Press and hold
the Programme Selection / Programme Cancel keys for 3 seconds. After the 3 2 - 1 countdown, 0:01 is displayed, close the door of the product and wait for the
17
USA
draining process complete. Draining
is completed in 2 minutes and the
machine gives an audible warning
when it is completed.
Function keys
If you press any of the Function keys
during programme selection or time
delay selection, an affirmative key
signal will be heard provided that the
relevant function is supported by the
selected programme. Function will be
deemed selected when the indicator of
the selected function is lit.
To cancel the selected function, keep
the function key pressed until the
function indicator disappears.
6.2 PREPARING THE
MACHINE
1. Open the door of the dishwasher.
2. Place the dishes in accordance
with the instructions in the user
manual.
3. Make sure that the upper and lower
impellers rotate freely.
4. Put adequate amount of detergent
into the detergent dispenser.
6.3 PROGRAMME SELECTION
1. Press the On/Off button to turn on
your machine.
2. Check the Salt and Rinse Aid
indicators and add salt and/or rinse
aid if needed.
3. Refer to the table of “Programme
data and average consumption
values” to determine a washing
programme suitable for your
dishes.
4. Selected programme will start
when you close the door of your
machine.
18
USA
19
USA
75
158
High
+
+
40
8
40
8
25-40
70
140
-
-
+
+
40
8
-
-
-
(°F)
(°C)
(°F)
15-25 ml
ml
tsp
ml
tsp
ml
tsp
15 ml
+ 5 ml
+
+
+
+
120
20,2
5,34
-
-
-
-
75
14,4
3,80
Main wash
Dry
Sanitize
Duration (minutes)
Water (liters)
Water (gallons)
4,28
16,2
102
+
+
+
+
5-8
25-40
8
40
8
40
+
+
-
High
158
70
158
70
Pots & Pans
2
3
3,06-5,01
11,6-19,0
90-135
+
+
+
+
3-5
15-25
5
25
5-8
25-40
+
+
-
Medium
142-154
61-68
122-131
50-55
Regular Wash *
PROGRAM TABLE
5,00
19
100
+
+
+
-
3-5
15-25
5
25
5-8
25-40
+
+
-
Medium
158
70
140
60
DailyWash
4
3,10
11,6
35
-
-
+
-
3
15
3
15
3-5
15-25
-
-
+
Few
131
55
113
45
Quick Wash
5
1,20
4,4
12
-
-
-
+
-
-
-
-
-
-
-
-
-
-
0
0
0
0
Rinse & Hold
6
The consumption values shown in the table were determined under standard conditions. For this reason, deviations are possible under practical conditions. * The energy-usage
label is based on this program.
5-8
-
Soft
water
Medium
water
Hard
water
70
167
72
160
(°C)
Pots & Pans+
1
ProCare
0
Wash
Recommended
detergent
amount
Detergent in
dispenser
section
Degree of dirtiness
Rinse Temperatures
Wash Temperatures
Program name
Program number
6.4 AUXILIARY FUNCTIONS
Washing programmes of your
dishwasher are designed to obtain the
best cleaning effect, considering the
type of the soiling, soiling degree and
properties of the dishes to be washed.
Auxiliary functions allow you save from
time, water and power.
Auxiliary functions may
cause changes in the
programme duration.
C
C
Auxiliary functions are not
suitable for all washing
programs. Indicator of the
auxiliary function that is
not compatible with the
programme will not be
active.
Half Load function
It is used to operate the machine
without loading it completely.
1. Load your dishes in the machine as
you like.
2. Turn the machine on with On/Off
key.
3. Select the desired programme
and press the Half Load key. The
Half Load indicator will light on the
display in the Function Selected
indicator.
4. Close the door of the machine to
start the programme.
C
With the Half Load function
you can save both water and
power while using the lower
and upper baskets of the
machine.
20
Sanitize Function
Sanitize function raises the water
temperature in the final rinse to
meet the requirements of NSF/ANSI
STANDARD 184 for Residential
Dishwashers. Certified residential
dishwashers are not intended for
licensed food establishments.
At the end of a succesfull
sanitization “S“ is displayed
on the display. “S” is not
displayed on the display if
the cycle is interrupted or the
water could not be heated to
the required temperature.
C
C
C
Available programs are
indicated on Program Table
chart.
Note: Only sanitizing cycles
have been designed to meet
the requirements of 6 for
soil removal and sanitization
efficacy.
There is no intention, either
directly or indirectly, that
all cycles have passed
sanitization performance
tests.
Extra Rinse function
Depending on the type of the detergent
used, if a detergent dissolving issue is
encountered it will remove the resulting
stains from the dishes and enables the
optimum rinsing performance.
Rapid Clean
It shortens the time of the washing
cycle selected and decreases water
consumption by enabling washing
under higher pressure.
USA
Interior Lighting
(MODEL DEPENDING)
Some models have interior lighting to
illuminate the interior when the door is
opened.
Changing the interior lighting
setting
1. After turning on the machine,
press Time Delay and P+ keys
simultaneously. Continue to press
until the countdown 3, 2, 1 is
completed on the display.
2. Press P+ key to activate the L:
option. The interior lighting is
turned off at "L:0" option and turned
on at "L:1" option. Set the desired
option with the Time Delay key.
3. Turn off the machine with On/Off
key to save the changes.
detection feature is disabled at
“a:0” option and enabled at "a:1"
option. Set the desired option by
pressing the Time Delay key.
3. Turn off the machine with On/Off
key to save the changes.
Automatic Detergent Detection
Feature
The product has a feature to
automatically detect the type of the
detergent and adjust the washing
programme and drying system to the
best performance. If special tablet
detergent is used, the programme
duration can be extended by 20
minutes in order to optimize the
washing and drying performance.
Notice: Automatic detergent
detection feature should be
deactivated during the tests
according to AHAM DW-1.
C
C
To deactivate:
1. After turning on the machine,
press Time Delay and P keys
simultaneously. Keep them
pressed until the countdown 3, 2, 1
is completed on the display.
2. Press P key to activate the a:
option. Automatic detergent
21
Floor illumination
Warning to show that machine is in
washing phase
(MODEL DEPENDING)
Your machine reflects a light to the
floor during the washing process. This
light turns off after the washing process
is complete.
Floor illumination is activated
automatically when the
washing programme starts
and remains lit until the end
of the programme.
C
Floor illumination cannot be
cancelled by the user.
Changing Warning Sound Volume
1. After turning on the machine,
press Time Delay and P / P+
keys simultaneously. Keep them
pressed until the countdown 3, 2, 1
is completed on the display.
2. Press P / P+ key to activate the S:
position.
3. Each pressing on the Time Delay
key will change the warning sound
volume as "S:0" off, "S:1" medium"
and "S:2" high.
4. Turn off the machine with On/Off
key to save the changes.
C
USA
Factory setting of your
machine is "S:2".
6.5 SCHEDULING THE
WASHING TIME
Time Delay
If an economical electricity tariff is
applied in your region, you can use
the Time Delay function to wash your
dishes during appropriate hours.
You can delay the start of the selected
programme until 24 hours.
1. Press the Time Delay function
key after selecting the washing
programme and other auxiliary
functions.
2. Once you press the Time Delay
key, Display Information Line
will show "0:30" and Time Delay
indicator will start flashing.
3. Set the desired time by pressing
the Time Delay key. Time will
increase with increments of 30
minutes up to 6 hours and after
that in 1 hour increments up to 24
hours every time you press the key.
4. Close the door of your machine
after setting the Delayed Start.
Once the delay time is over, the
selected programme will start
automatically.
Changing the settings while Time
Delay function is active
While the Time Delay function is
activated, you cannot make changes
in the washing programme, auxiliary
functions or the duration of delay time.
Programme and auxiliary
functions cannot be
set/changed after the
programme has started.
C
To cancel the Time Delay function
Open the door of the product Press
and hold the Programme Selection
/ Programme Cancel keys for 3
seconds. After the 3 - 2 - 1 countdown,
22
0:01 is displayed, close the door of
the product and wait for the draining
process complete. Draining is
completed in 2 minutes and the
machine gives an audible warning
when it is completed.
You can select and start a
new programme following
the cancellation of Time
Delay function.
C
C
Time Delay function cannot
be set after the programme
starts.
6.6 STARTING THE
PROGRAMME
Close the door of your machine to start
it after selecting the programme and
auxiliary functions.
MODEL DEPENDING:
Your machine performs
water softening depending
on the hardness level of
the supply water. Washing
time can change while
the programme is running
depending on the ambient
temperature where your
machine is installed,
temperature of the supply
water and amount of the
dishes.
C
C
C
USA
Pay attention not to open the
door of the machine when
it is running. There may
be a rush of vapour when
you open the door of your
machine; be careful.
The machine will be
switched off if no button is
pressed within 5 seconds
after opening the door while
the machine is running.
C
C
After the door has been
opened, if any button is
pressed within 5 seconds
and the door is closed,
the selected programme
resumes; otherwise, the
machine will be switched off.
Open the door after the
machine has been switched
off, press On/Off button
and close the door within 5
seconds. The programme
will resume washing.
6.8 SALT INDICATOR (
The machine will remain
silent in pause mode for
some time in order to
remove the water from the
machine and on the dishes
completely and to have the
water softener cleaned, and
then it will resume running in
drying mode.
6.9 RINSE AID INDICATOR ( )
6.7 CANCELLING THE
PROGRAMME
Open the door of the product Press
and hold the Programme Selection
/ Programme Cancel keys for 3
seconds. After the 3 - 2 - 1 countdown,
0:01 is displayed, close the door of
the product and wait for the draining
process complete. Draining is
completed in 2 minutes and the
machine gives an audible warning
when it is completed.
There might be residues
of detergent or rinse aid
in the machine and/or on
the pieces being washed
depending on the step
the programme you have
cancelled was in.
C
23
)
(MODEL DEPENDING)
Please check the salt indicator on
the display to see whether there is
adequate amount of softening salt
in the dishwasher or not. You need
to refill the salt reservoir with salt
whenever salt indicator appears on the
display of your machine.
Adjusting the water hardness
level is explained in Water
Softening System section.
C
Please check the rinse aid indicator
on the display to see whether there is
adequate amount of rinse aid in the
dishwasher or not. You need to refill
the rinse aid reservoir with rinse aid
whenever rinse aid indicator appears
on the display of your machine.
6.10 END OF PROGRAMME
C
When the programme you
have selected comes to an
end, an audible warning
signal will warn you to turn
off your machine. This
audible signal will warn you
with certain intervals before
it turns off.
End of Programme indicator will light
up when the washing programme is
over.
1. Open the door of the machine.
2. Press On/Off key to turn off your
machine.
3. Close the tap.
4. Unplug the machine from the
socket.
USA
C
C
disappear, there is a permanent fault.
In this case the authorised service
should be contacted.
For energy saving, the
machine is automatically
turned off following
the completion of the
programme or if the
programme is not started.
Leave your dishes in the
machine for about 15
minutes to allow them cool
down after they are washed.
Your dishes will dry in a
shorter time if you leave
the door of your machine
ajar during this period. This
process will increase the
drying effectiveness of your
machine.
ProCare
This programme is recommended
to be operated on each 1-2 months
for machine cleaning and necessary
hygiene. The programme should be
operated while the machine is empty.
In order to achieve an efficient result, it
is recommended to use together with
special machine cleaning agents.
Do not use this programme
to clean dishes. As
it operates in high
temperatures, it is harmful
for the dishes.
C
6.11 WATER CUT-OFF
WARNING
If mains water is cut or water inlet
tap is turned off the machine cannot
take water in and E:02 icon will flash
on the programme indicator. As long
as the problem continues, washing
programme is paused and the water
inlet is checked regularly by the
machine; when the water is restored
E:02 icon will disappear after a while
and the washing programme resumes.
6.12 OVERFLOWING
WARNING
If the machine intakes too much
water or there is leakage at any of
the components then the machine
will detect this and E:01 icon will flash
on the Programme indicator. As long
as the overflowing continues safety
algorithm will be active and try to
discharge the water. If overflowing
stops and safety is assured, E:01
icon will disappear. If E:01 does not
24
USA
7. DETERGENT & RINSE AID
DISPENSER
7.1 FILLING THE DETERGENT
DISPENSER
A
••
WARNING:Always store
your detergent in locations
which are cool, dry and out
of the reach of children.
Check that the detergent
dispenser is empty after the
completion of each wash
program.
WARNING:Dishwasher
detergents can be dangerous
if inhaled or swallowed.
Avoid contact with skin and
eyes, keep children and
infirm persons away from the
dishwasher when the door
is opened. Consult a doctor
immediately if detergent has
been swallowed or inhaled.
A
••
••
••
••
••
Only use detergents suitable for
dishwashers.
Do not use detergent in Rinse &
Hold cycle.
Don’t forget to pour / put the
detergent into the dispenser
before turning the machine on.
Too much detergent may mean
that the detergent does not
dissolve properly and dishes could
get scratched.
Too much detergent in soft water
may cause glass corrosion. Do
not use too much detergent if your
water supply is soft.
25
If you do not know the hardness
of your water supply, use 15 ml / 3
tsp detergent. Increase the amount
of detergent if you see white water
marks especially on the surface of the
glassware.
Find out the hardness of your water
supply by asking your local water
department, water softener company,
or county extension agent.
1.
2.
3.
USA
Open the detergent container by
pushing the lock to the right A.
Pour / put the detergent into the
dispenser.
Close the lid until it clicks in.The
detergent container holds a total
of 40 ml / 8 tsp of detergent
1.Marking lines on the inside of
the detergent container aid in
providing the correct amount of
detergent. When the dishwasher
is fully loaded and the dishes are
very dirty, we recommend filling
the detergent container up to
the 25 ml / 5 tsp mark. When the
dishes are less dirty, it is generally
sufficient to fill the detergent up to
the 15 ml / 3 tsp mark.
7.2 FILLING RINSE AID
DISPENSER
A
••
••
••
••
••
••
The detergent amounts for the
individual cleaning programs are
shown in the “Quick Reference
Guide - Program Table”.
Fill amounts given are for standard
powder detergent. Amounts
may vary if you use liquid or
concentrated powder detergent.
Tablet detergents should be
placed in detergent container 1.
With the cover closed.
Follow instructions on the package
of the detergent when using
liquid dishwasher detergent,
concentrated powder detergent, or
tablet detergent.
Deviations are possible depending
on how dirty the dishes are and
how hard the water is in your
location.
If your dishes have been in the
dishwasher for some time without
being washed, also fill the smaller
container 2. up to the top.
26
••
WARNING:Keep your
rinse aids out of the reach
of children. Ingestion or
inhalation of rinse aid may
cause serious injury. Avoid
contact with skin and eyes,
and keep children and infirm
persons away from rinse
aids.
Only use rinse aids suited for use
in dishwashers. Rinse aids allow
washing water to rinse off more
cleanly and prevent watermarks or
streaks on the dishes.
If you use “2 in 1” or “3 in 1”
detergents / tabs, you do not
need additional rinse aid.
1.
2.
USA
Open the rinse aid dispenser by
pressing the lock B.
Carefully pour in rinse aid to the
MAX mark.
3.
4.
Close the lid until it clicks in 3.
Carefully wipe off spilled rinse
aid. Excessive rinse aid causes
excessive foam formation, which
may hinder cleaning.
7.3 SET THE DOSE OF RINSE
AID
The dose of rinse aid to be used can
be set by means of the dispenser
regulator 4 between levels 1 and 6.
Change the setting, only if the following
applies after washing:
•• Watermarks are visible on the
dishes: Set dosage higher.
•• Streaks are visible on the dishes:
Set dosage lower.
27
USA
8. SETTING THE WATER SOFTENER
(MODEL DEPENDING)
WATER HARDNESS & REGENERATION SETTINGS
The dishwasher requires lime free water. Hard water leaves watermarks on your
dishes. Your dishwasher has a special water softening system to remove the
hardness of the tap water. Setting this system correctly will increase the washing
effectiveness.
To find out the hardness level of water in your area, contact your local Water
Board or Determine water hardness level by the help of test strip provided.
If you move to a different location, the level of water hardness will possibly
be different. It is essential to reset the water hardness in order to obtain
optimum washing efficiency.
Test Strip
Remove the
Let the water Fill a glass with Take the test strip
test strip from flow from your tap water and out of the water and
its packing. tap for 1 minute. dip the test strip
shake it.
into water for 1
second.
Hold for
1 minute.
Level 1
No Lime
Level 2
Very low lime content
Level 3
Low lime content
Level 4
Medium lime content
Level 5
High lime content
Level 6
Very High lime content
Set the water hardness level of your dishwasher
according to the result shown by the test strip.
To Adjust the Water Hardness
1. After turning on the machine, press Time Delay and P+/P keys simultaneously.
After the countdown (3,2,1) is displayed keep the keys pressed for a while.
2. Press P+/P key to activate the position.
3. Using Time Delay key, adjust water hardness level according to the hardness of
the supply water. See “Water hardness level adjustment table” for correct setting.
4. Press On / Off key to save the setting.
Water Hardness Level Adjustment Table
Hardness
Level
1st Level
2nd Level
3rd Level
4th Level
5 Level
English
Water
Hardness
°dE
German
Water
Hardness
°dH
French
Water
Hardness
°dF*
0-5
0-4
0-8
6-9
5-7
9-13
10-15
8-12
14-22
Press the Time Delay key to switch the water hardness level to position 2. (r 2)
16-19
13-15
23-27
Press the Time Delay key to switch the water hardness level to position 3. (r 3)
20-24
16-19
28-34
Press the Time Delay key to switch the water hardness level to position 4. (r 4)
25-62
20-50
35-90
Press the Time Delay key to switch the water hardness level to position 5. (r 5)
Water Hardness Level Indicator
Press the Time Delay key to switch the water hardness level to position 1. (r 1)
th
6th Level
28
USA
If the hardness level of the water
that you use is above 90°dF (French
standard for water hardness) or if
you are using well water, than it is
recommended to use filter and water
purification devices.
*
If the hardness level of the water
that you use is below 8°dF (French
standard for water hardness),
there is no need to use salt in your
dishwasher. If this is the case,
Salt Indicator (if any) illuminates
continuously on the panel of your
machine.
If the water hardness is set to level
1, the Salt Indicator will illuminate
continuously although it is not
necessary to use salt. If you use
salt under this condition, salt will not
be consumed and the lamp will not
illuminate.
If you move your house, it
is very important to make
the water hardness level
adjustment of your machine
according to the new
location you move in order
to preserve the washing
efficiency.
If the water hardness
level of your machine is
adjusted previously, your
machine will display the
most recent hardness level
adjustment. Adjust the new
water hardness level of the
machine based on the water
hardness level of the tap
water.
C
29
9. FILLING THE DISHWASHER
SALT DISPENSER
(MODEL DEPENDING)
A
C
1.
CAUTION :Never use
culinary or table salt. These
types of salt do not dissolve
in water easily and will
damage the function of the
softening device.
NOTICE: Only use special
dishwasher salt in your
machine to soften the water.
Do not use coarse grained
salt. Small grains or
powdered salt is more easily
soluble.
The manufacturer is not
liable for damages resulting
from the use of the wrong
type of salt.
Remove the lower rack from the
machine.
USA
2.
10. CARE AND MAINTENANCE
Open the screw-in cap of the salt
container by turning it counter
clockwise (Fig. A, B).
A
A
3.
When operating for the first time:
Pour 1 Liter of water into the salt
container (Fig. C).
A
4.
5.
Pour the salt into the container
with the aid of the supplied salt
funnel (Fig. D). Pour in enough
salt to fill the container. The
container holds approximately 2 kg
/ 4.4 pounds.
Close the cap tightly.
CAUTION :Begin any wash
program immediately after
filling the salt container. The
washing program prevents
damage to the machine
which may be caused by any
spilled salt solution.
A
After the first washing cycle, the salt
level indicator light will go out. (model
depending)
30
USA
WARNING:Before cleaning
or carrying out maintenance,
switch off the appliance,
disconnect the mains plug
and turn off the water tap.
WARNING:Do not repair
or replace any part of the
dishwasher or attempt any
servicing unless specifically
recommended by this
manual. We recommend
that the dishwasher only be
repaired by an authorized
service agent.
CAUTION :To avoid the
possibility of slipping,
keep the floor around the
dishwasher clean and dry.
Keep your appliance free
from the accumulation of
combustible materials, such
as lint, rags, and chemicals.
If the dishwasher is not in
use for an extended period
of time, we recommend you
check that the baskets are
empty, leave the inside of the
dishwasher clean, the door
cracked open to allow air to
circulate, turn off both the
power and water supply to
the dishwasher.
10.1 CARING FOR YOUR
DISHWASHER EXTERIOR
A
10.2 CARING FOR YOUR
DISHWASHER INTERIOR
CAUTION :Possible
dishwasher damage:
Abrasive cleaners, scouring
pads, abrasive cloths (paper
towels) can damage the
dishwasher decorative door.
Cleaning the control panel: Use only
soft cloth that is lightly dampened with
mild detergent. Clean the control panel
only with a moist cloth and clear water.
C
A
Cleaning the colored doors: Use only
soft cloth that is lightly dampened with
mild detergent.
Cleaning the stainless steel doors:
Use a soft cloth with a cleaner made
for cleaning stainless steel. For the
best results, apply the stainless steel
cleaner to a soft cloth and wipe the
surface in the direction of the grain.
Cleaning the door gasket: Regularly
clean the door gasket with a damp
cloth to remove food particles and
other debris. Use a gentle household
cleaner for the outside and the door
seals, and rinse thoroughly.
31
USA
NOTICE: Cleaning your
dishwasher at regular
intervals ensures longer
product life and reduces the
risk of recurring problems.
Always disconnect the power
to machine before cleaning.
CAUTION :When cleaning
the underside of the main
filter, care must be taken on
the sharp outer edge to avoid
the risk of cut type injuries.
10.3 CLEANING THE FILTERS
Clean the filters at least once a week
in order for the machine operates
efficiently. Check if food residues are
left on the filters. If there are food
residues on filters, take them out and
clean well under running water.
1. Turn the micro filter (1) and coarse
filter (2) assembly counterclockwise
and pull it out from its seating (A).
4. Clean all three filters under tap
water by means of a brush.
5. Replace the metal/plastic filter.
6. Place the coarse filter into the
microfilter. Make sure that it is
properly seated. Turn the coarse
filter clockwise until a “click” sound
is heard.
C
C
2. Pull out the metal / plastic filter (3)
from the seating (C).
3. Press the two pawls on the coarse
filter inwards and separate the
coarse filter from the assembly (B).
32
USA
Do not use the dishwasher
without filter.
Incorrect placement of the
filters will reduce washing
efficiency.
10.4 CLEANING THE HOSE
FILTER
10.5 CLEANING THE
IMPELLERS
Damages on the machine that may be
caused by impurities coming from the
urban supply water or your own water
installation (such as sand, dirt, rust,
etc.) can be prevented by means of the
filter attached to the water inlet hose.
Check the filter and the hose regularly
and clean them if necessary.
1. Turn off the tap and remove the
hose.
2. After taking out the filter, clean it
under running tap water.
3. Place the cleaned filter back to its
seat in the hose.
4. Install the hose to tap.
Clean the impellers at least once a
week in order for the machine operates
efficiently.
LOWER IMPELLER
Check if the holes on the lower impeller
(1) are clogged. If they are clogged,
remove and clean the impeller. Pull the
lower impeller up to remove it (A, B).
(MODEL DEPENDING)
33
USA
UPPER IMPELLER
Check if the holes on the upper
impeller (1) are clogged. If they
are clogged, remove and clean the
impeller. Turn its nut to left to remove
the upper impeller (A, B).
Make sure that the nut is tightened well
when installing the upper impeller.
CEILING IMPELLER
(MODEL DEPENDING)
Check if the holes on the top ceiling
impeller (1) of your machine are
clogged. If they are clogged, remove
and clean.
To remove them, slightly ( ) push them
upwards and then ( ) turn left (A,B).
To install the impeller, seat it into its
slot, push slightly upwards and turn it
rightwards until it is securely tightened.
When the impeller is released, check if
it rotates without any obstruction.
34
USA
11. TROUBLESHOOTING
Machine does not start.
•• Power cable is unplugged. >>> Check if the power cable is plugged in.
•• Fuse is blown. >>> Check the fuses in your house.
•• Water is cut. >>> Make sure that the water inlet tap is open.
•• Door of the machine is open. >>> Make sure that you have closed the door of
the machine.
•• On / Off button is not pressed. >>> Make sure that you have turned on the
machine by pressing the On / Off button.
Dishes are not washed clean
•• Dishes are not placed orderly in the machine. >>> Load the dishes as
described in the user manual.
•• Selected programme is unsuitable. >>> Select a programme with a higher
temperature and cycle time.
•• Impellers are stuck. >>> Prior to starting the programme, turn the lower and
upper impellers by hand to make sure that they rotate freely.
•• Impeller holes are clogged. >>> Lower and upper impeller holes might be
clogged with food remnants such as lemon pips. Clean the impellers regularly
as illustrated in section “Cleaning and Care”.
•• Filters are clogged. >>> Check if the filter system is clean. Clean the filter
system regularly as illustrated in section “Cleaning and Care”.
•• Filters are installed incorrectly. >>> Check the filter system and make sure
that it is installed correctly.
•• Baskets are overloaded. >>> Do not overload the baskets in excess of their
capacity.
•• Detergent is stored under unsuitable conditions. >>> If you are using powder
detergent, do not store the detergent package in humid places. Keep it in a
closed container if possible. For ease-of-storing, we recommend you to use
tablet detergents.
•• Detergent is not sufficient. >>> If you are using powder detergent, adjust
the amount of detergent according to the soiling degree of your dishes and/
or programme definitions. We recommend you to use tablet detergents for
optimum results.
•• Rinse aid is not sufficient. >>> Check the rinse aid indicator and add rinse
aid if necessary. Increase the rinse aid setting if there is enough amount of
rinse aid in the machine.
•• Detergent dispenser lid is left open. >>> Make sure that the detergent
dispenser lid is closed tightly after adding detergent.
Dishes are not dry at the end of cycle
•• Dishes are not placed orderly in the machine. >>> Place your dishes in a way
that no water will accumulate in them.
•• Rinse aid is not sufficient. >>> Check the rinse aid indicator and add rinse
aid if necessary. Increase the rinse aid setting if there is enough amount of
rinse aid in the machine.
•• Machine is unloaded right after the programme is over. >>> Do not unload
your machine right after washing process is completed. Slightly open the
35
USA
••
••
door and wait for evacuation of the steam inside for a while. Unload the
dishes after the pieces cool down to a touchable level. Start unloading
process from the lower basket. Thus, dropping of water remained on a piece
at upper basket onto the pieces at lower basket is prevented.
Selected programme is unsuitable. >>> Since rinsing temperature is low at
programmes with short duration, drying performance will also be low. Select
programmes with longer duration for a higher drying performance.
Surface quality of the kitchen utensils is deteriorated. >>> Desired washing
performance can not be obtained at kitchen utensils with deteriorated
surfaces and it is not suitable to use such utensils in terms of hygiene
as well. Also, water can not flow easily on deteriorated surfaces. It is not
recommended to wash such kitchen utensils in dishwasher.
It is normal that drying complaints can be experienced with Teflon
kitchen utensils. It is associated with the structure of Teflon. Since the
surface tensions of Teflon and water are different, water droplets will
remain as beads on the Teflon surface.
C
Tea, cafe or lipstick stains remain on dishes.
•• Selected programme is unsuitable. >>> Select a programme with a higher
temperature and cycle time.
•• Surface quality of the kitchen utensils is deteriorated. >>> Tea and cafe
stains or other dye spots may not be cleaned in dishwasher when they have
penetrated in deteriorated surfaces. Desired washing performance can not be
obtained at kitchen utensils with deteriorated surfaces and it is not suitable to
use such utensils in terms of hygiene as well. It is not recommended to wash
such kitchen utensils in dishwasher.
•• Detergent is stored under unsuitable conditions. >>> If you are using powder
detergent, do not store the detergent package in humid places. Keep it in a
closed container if possible. For ease-of-storing, we recommend you to use
tablet detergents.
Lime traces remain on dishes and glassware gains a misty appearance
•• Rinse aid is not sufficient. >>> Check the rinse aid indicator and add rinse aid
if necessary. Increase the rinse aid setting if there is enough amount of rinse
aid in the machine.
•• Water hardness setting is low or salt level is insufficient >>> Measure the
hardness of the supply water appropriately and check the water hardness
setting.
•• Salt leakage exists. >>> Pay attention not to spill salt around the salt filling
hole while adding salt. Make sure that the salt reservoir lid is tightly closed
after finishing the filling process. Run the prewash programme to remove the
salt that spilled inside the machine. Since the salt granules that will remain
under the lid will dissolve during prewash, causing the lid loosen, check the
lid once again at the end of the programme.
36
USA
There is a different odour in the machine
C
A new machine has a peculiar odour. It will fade out after a couple of
washing.
••
Filters are clogged. >>> Check if the filter system is clean. Clean the filter
system regularly as illustrated in section “Cleaning and Care”.
•• Dirty dishes are kept in dishwasher for 2-3 days. >>> If you are not going
to start the machine right after you have put the dishes into it, remove the
remnants on the dishes and run the Prewash programme without detergent
every 2 days. In such cases, do not close the door of the machine completely
in order to avoid odour build up in machine. You can also use commercially
available odour removers or machine cleaners.
Rust, discoloration or surface deterioration occurs on dishes
•• Salt leakage exists. >>> Salt may cause deterioration and oxidation on metal
surfaces. Pay attention not to spill salt around the salt filling hole while adding
salt. Make sure that the salt reservoir lid is tightly closed after finishing the
filling process. Run the prewash programme to remove the salt that spilled
inside the machine. Since the salt granules that will remain under the lid will
dissolve during prewash, causing the lid loosen, check the lid once again at
the end of the programme.
•• Salty food remnants have remained on dishes for a long time. >>> If
silverware soiled with such foods will be kept waiting in machine, dirt must be
removed by prewash or dishes must be washed without being kept waiting.
•• Electric installation is not grounded. >>>Check if your machine is connected
to the actual grounding line. Otherwise, the static electric created in the
product causes arcs on the surfaces of metal items creating pores, removing
the protective cover on the surface and causing discoloration.
•• Intensive cleansers such as bleaches are used. >>> Protective cover on
metal surfaces gets damaged and looses its efficiency in time when it gets in
contact with cleansers such as bleach. Do not wash your dishes with bleach.
•• Metal items particularly such as knives are used for purposes other then
their intended uses. >>> Protective cover on the edges of knives may get
damaged when they are used for purposes such as opening cans. Do not
use metal kitchen utensils out of their intended uses.
•• Silverware are made of low quality stainless steel. >>> Corrosion on such
items is inevitable; they should not be washed in dishwashers.
•• Kitchen utensils that are already corroded are washed in dishwasher. >>>
Rust on a corroded item can migrate to other stainless steel surfaces and
cause corrosion on those surfaces as well. Such items should not be washed
in dishwashers.
37
USA
Detergent remains in detergent dispenser.
•• Detergent dispenser was damp when adding detergent. >>> Make sure that
the detergent dispenser is dried well prior to filling it with detergent.
•• Detergent is added long before the washing process. >>> Pay attention to
add detergent shortly before start-up of the washing.
•• Opening of the detergent dispenser lid is prevented during washing. >>>
Place the dishes in a way that will not prevent the detergent dispenser lid
from opening and the water going into the machine from impellers.
•• Detergent is stored under unsuitable conditions. >>> If you are using powder
detergent, do not store the detergent package in humid places. Keep it in a
closed container if possible. For ease-of-storing, we recommend you to use
tablet detergents.
•• Impeller holes are clogged. >>> Lower and upper impeller holes might be
clogged with food remnants such as lemon pips. Clean the impellers regularly
as illustrated in section “Cleaning and Care”.
Decorations and ornaments on kitchen utensils are being erased.
C
Decorated glasses and decorated luster porcelains are not suitable for
washing in the dishwasher. Manufacturers of glassware and porcelain
tableware items do not recommend washing such kitchen utensils in
the dishwashers either.
Dishes are scratched.
C
••
••
••
Kitchen utensils that contains or are made of aluminum should not be
washed in dishwasher.
Salt leakage exists. >>> Pay attention not to spill salt around the salt filling
hole while adding salt. Spilled salt can cause scratches. Make sure that the
salt reservoir lid is tightly closed after finishing the filling process. Run the
prewash programme to remove the salt that spilled inside the machine. Since
the salt granules that will remain under the lid will dissolve during prewash,
causing the lid loosen, check the lid once again at the end of the programme.
Water hardness setting is low or salt level is insufficient >>> Measure the
hardness of the supply water appropriately and check the water hardness
setting.
Dishes are not placed orderly in the machine. >>> When placing the glasses
and other glassware into the basket lean them not against other dishes but
the edges or racks of the basket or the glass support wire. Striking of the
glasses to each other or to other dishes due to the impact of water during
washing can cause breaks, or scratches on their surfaces.
38
USA
A smear remains on glasses that resembles milk stain which can not be
removed when wiped by hand. A bluish / rainbow appearance occurs when
the glass is pointed to light.
•• Excessive rinse aid is used. >>>Lower rinse aid setting. Clean the spilled
rinse aid when adding rinse aid.
•• Corrosion has occurred on glass due to soft water. >>> Measure the
hardness of the supply water appropriately and check the water hardness
setting. If your supply water is soft (<5 dH), do not use salt. Choose
programmes that wash in higher temperatures (e.g. 60-65°C). You can also
use glass protective detergents that are commercially available.
Foam forms in the machine.
•• Dishes are washed with hand-wash detergent by hand but not rinsed before
placing them into the machine. >>> Hand-wash detergents do not contain
antifoam. There is no need to hand-wash the dishes before placing them into
the machine. Removing the coarse soil on the dishes under tap water, with a
tissue paper or fork will be sufficient.
•• Rinse aid has spilled into the machine when adding rinse aid. >>> Take care
that rinse aid is not spilled in the machine when you are filling it. Clean any
spilled rinse ait with the help of a tissue paper/towel.
•• Lid of the rinse aid reservoir is left open. >>> Make sure that the lid of the
rinse aid reservoir is closed after adding rinse aid.
Kitchen utensils are broken.
•• Dishes are not placed orderly in the machine. >>> Load the dishes as
described in the user manual.
•• Baskets are overloaded. >>> Do not overload the baskets in excess of their
capacity.
Water remains in the dishwasher at the end of the programme.
•• Filters are clogged. >>> Check if the filter system is clean. Clean the filter
system regularly as illustrated in section “Cleaning and Care”.
•• Discharge hose is clogged/blocked. >>> Check the discharge hose. If
necessary, remove the discharge hose, clear the blockage and insert is as
illustrated in the user manual.
39
USA
C
If you cannot eliminate the problem although you follow the
instructions in this section, consult your dealer or the Authorised
Service Agent. Never try to repair a nonfunctional product yourself.
12. TECHNICAL FEATURES
Load capacity
Permissible water
pressure
Electrical connection
Total power
Heater power
C
14 place settings
4.35 - 145 psi (0.3 - 10 bars)
120 V (volts), 12 A (amps), 60Hz (hertz)
1400 W (watts)
1240 W (watts)
NOTICE: Because we
continually strive to improve
our products, we may
change our specifications
and design without prior
notice.
This device corresponds to
the following directives:
UL 749 Household
Dishwasher directive.
40
USA
13. WARRANTY STATEMENT FOR THE BLOMBERG
DISHWASHERS
The warranties provided by Blomberg
in these statements only apply to
Blomberg dishwashers sold to the
original purchaser or homeowner in
the US and Canada. The warranty is
not transferable. To obtain warranty
service, please contact our nearest
distributor as listed by state. You
will need your dishwasher model
number, serial number, retailer name
and address, where purchased and
purchase date / installation date. This
warranty gives you specific legal rights,
and you may also have other rights
which vary from state to state.
“This product is fully tested and went
through official quality assurance
inspections before leaving the original
manufacturing site. Warranty terms
for this Blomberg household appliance
is not valid if the product is altered,
tampered, modifed, additional parts
assembled, fixed and re-packed by an
authorized distributor, servicer, a third
party retailer, reseller or by any other
unauthorized person(s)”
1 year * limited warranty from date of
first installation
Blomberg will repair or replace at no
cost to the consumer any defective
parts of the dishwasher if used under
normal household conditions or is
installed at an employee kitchen, office
use, lodges, primary care facilities such
as elderly homes, etc. (warranty is void
if the product is installed high traffic
locations such as dormitories, school
kitchens, restaurants, cafetaries etc.
Please consult Blomberg authorized
distributor prior to operating the
41
unit about the warranty disclaimer).
Service must also be performed
by an authorized Blomberg service
agency. (Cosmetic defects must be
reported within 10 business days from
installation)
2 year * ++ limited warranty from
date of first installation
(Parts only) Blomberg will repair or
replace any parts at no cost to the
consumer if material defects or
workmanship have caused the damage
or failure of these components. Again
the dishwasher must have been
used under normal household
conditions and not commercially as
stated above (Labor charges are the
responsibility of the consumer).
5 year * ++ limited warranty from
date of first installation
(parts only 3-5 years) Blomberg will
repair or replace any circuit boards or
nylon dishwasher racks (excluding
any plastic rack attachments) at
no cost to the consumer if material
defects or workmanship have caused
the damage or failure of these
components. The dishwasher must
have been used under normal
household conditions and not
commercially (Labor charges are the
responsibility of the consumer)
Lifetime limited warranty from date
of first installation * ++
(parts only) Blomberg will repair
or replace to the original owner
the stainless steel tub or door if
rust through occurs under normal
household use and normal water
USA
conditions (no excessive chlorine).
Blomberg may, at its option, also
replace the whole dishwasher with
the same and/or equivalent model
with equal or better functionality if the
original model is no longer available.
(Labor, removal and installation
charges are the responsibility of the
consumer.)
Disclaimers of warranties and
exclusions:
Warranty does not cover service
costs by an authorized service
agent to correct installation,
electrical and plumbing problems
or educational instruction on the
use of the dishwasher. The warranty
also does not cover defects or
damage caused by an act of god
(such as storms, floods, fires,
mudslides, steam protection folio
etc.), damage cause by use of the
dishwasher for purposes other than
those for which it was designed,
misuse, disuse, abuse, accident,
alteration, improper installation,
maintenance, travel fees, service
calls outside normal service hours,
unauthorized service work.
TO THE EXTENT PERMITTED BY
LAW, THIS WARRANTY IS IN LIEU
OF ALL OTHER EXPRESSED AND
IMPLIED WARRANTIES, INCLUDING
THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE.
BLOMBERG UNDERTAKES NO
RESPONSIBILITY FOR THE
QUALITY OF THIS PRODUCT
EXCEPT AS OTHERWISE
PROVIDED IN THIS WARRANTY
STATEMENT. BLOMBERG ASSUMES
NO RESPONSIBILITY THAT THE
42
PRODUCT WILL BE FIT FOR ANY
PARTICULAR PURPOSE FOR
WHICH YOU MAY BE BUYING THIS
PRODUCT, EXCEPT AS OTHERWISE
PROVIDED IN THIS WARRANTY
STATEMENT.
Blomberg does not assume any
responsibility for incidential or
consequential damages. Such
damages include, but are not
limited to, loss of profits, loss of
savings or revenue, loss of use of
the dishwasher or any associated
equipment, cost of capital, cost of
any substitute equipment, facilities
or services, downtime, the claims of
third parties, and injury to property.
Some states do not allow the
exclusion or limitation of incidental
or consequential damages, so the
above limitations or exclusion may
not apply to you.
*
installation date shall
refer to either purchase date or 5
business days after delivery of the
product to the home, whichever is
later.
++
parts replaced will assume
the identity of the original parts +
their original warranty.
No Other Warranties. This Warranty
Statement is the complete and
exclusive warranty from the
manufacturer. No employee of
Blomberg or any other party is
authorized to make any warranty in
Statement addition to those made in
this Warranty Statement.
USA
14. HOW TO GET SERVICE
Please contact the Distributor for your
State or Province as listed on the
Distributor Contact List, or call our Toll
Free Number at 1 800 459 9848 for
direction to an Authorized Blomberg
Service Agent.
Document Number :
15 0571 01 00_AA_BLOMBERG_E5_USA/ 12-02-16.(15:11)
43
USA
www.blomberginternational.com
info@blomberginternational.com
Download PDF

advertising