U-Line | U3024RGLS01 | Installation guide | U-Line U3024RGLS01 Installation Guide

INSTALL GUIDE
®
MODULAR 3000 SERIES
WINE CAPTAIN®
MODELS
BEVERAGE
CENTERS
GLASS DOOR
REFRIGERATORS
REFRIGERATORS
U-3018WCOL-00
U-3024BEVOL-00
U-3018RGLOL-00
U-3018RFOL-00
U-3018WCOL-01
U-3024BEVOL-01
U-3018RGLOL-01
U-3018RFOL-01
U-3018WCS-00
U-3024BEVS-00
U-3018RGLS-00
U-3018RFS-00
U-3018WCS-01
U-3024BEVS-01
U-3018RGLS-01
U-3018RFS-01
U-3018WCS-13
U-3036BVWCOL-00
U-3018RGLS-13
U-3024RFOL-00
U-3018WCS-15
U-3036BVWCS-00
U-3018RGLS-15
U-3024RFOL-01
U-3024WCOL-00
U-3036BVWCS-13
U-3024RGLOL-00
U-3024RFS-00
U-3024WCOL-01
U-3024RGLOL-01
U-3024RFS-01
U-3024WCS-00
U-3024RGLS-00
U-3036RROL-00
U-3024WCS-01
U-3024RGLS-01
U-3036RRS-00
U-3036WCWCOL-00
U-3036RRGLOL-00
U-3036WCWCS-00
U-3036RRGLS-00
U-3036WCWCS-13
U-3036RRGLS-13
THE MODULAR 3000 SERIES ARE INTENDED FOR BUILT IN INSTALLATIONS ONLY
The Built-In Undercounter Leader Since 1962
U-LINE.COM
1 Table of Contents
Safety Precautions
Safety Alert Definitions ........................................................................................................................................ 1
General Precautions.............................................................................................................................................. 1
Inspect & Plan
Product Registration ............................................................................................................................................. 2
Product Description.............................................................................................................................................. 2
Exterior Cleaning................................................................................................................................................... 2
Prepare Site
Electrical Specifications......................................................................................................................................... 3
Cut-Out Dimensions ............................................................................................................................................ 3
3018 Series ................................................................................................................................................... 3
3024 Series ................................................................................................................................................... 3
3036 Series ................................................................................................................................................... 3
Product Dimensions
3018, 3024 & 3036 Series ......................................................................................................................... 4
Door Swing Dimensions
Other Site Requirements..................................................................................................................................... 5
Side-By-Side Installation ............................................................................................................................ 5
Power Supply ............................................................................................................................................... 5
Environmental Requirements................................................................................................................... 5
3000 Series Doors
Door Alignment and Adjustment....................................................................................................................... 6
3000 Series Overlays
Overlay / Frame Overlay Panel .......................................................................................................................... 7
Panel Preparation........................................................................................................................................ 7
Panel Installation ......................................................................................................................................... 8
Overlay Grille ......................................................................................................................................................... 9
3000 Series Anti-Tip Bracket
Anti-Tip Brackets Installation............................................................................................................................11
Level & Install
Leveling Information............................................................................................................................................13
Installation..............................................................................................................................................................13
Relocating the Shelves ............................................................................................................................. 13
Installation Troubleshooting................................................................................................................... 13
General Precautions
2 Safety Precautions
IMPORTANT
• PLEASE READ all instructions before installing,
operating, or servicing the appliance.
• Proper installation procedures must be followed when
completing an installation or relocation of a unit.
Consult the installation guide before any installation
begins. U-Line contact information appears on the rear
cover of this guide.
• This unit requires connection to a dedicated 15 Amp
grounded (three-prong), polarized receptacle.
Receptacle should be installed by a qualified electrician,
compliant with applicable electrical codes.
Safety Alert Definitions
Throughout this guide are safety items labeled with a Danger,
Warning or Caution based on the risk type:
Use this appliance for its intended purpose only. The 3000 model
series is intended for BUILT IN installation only. Anti tip
brackets MUST be installed. Follow these general precautions
with those listed throughout this guide:
DANGER
RISK OF CHILD ENTRAPMENT. Before you throw away your
old refrigerator or freezer, take off the doors and leave shelves
in place so children may not easily climb inside.
WARNING
SHOCK HAZARD - Electrical Grounding Required.
• Never attempt to repair or perform maintenance on
the unit until the electricity has been disconnected.
• Never remove the round grounding prong from the
plug and never use a two-prong grounding adaptor.
• Altering, cutting of power cord, removal of power
cord, removal of power plug, or direct wiring can
cause serious injury, fire and or loss of property and
or life, and will void the warranty.
• Never use an extension cord to connect power to the
unit.
• Always keep your working area dry.
WARNING
DANGER
Danger means that failure to follow this safety statement will
result in severe personal injury or death.
Install provided Anti-Tip kit on all models. Units
may NOT be installed as free standing. Serious
personal injury could occur.
CAUTION
WARNING
Warning means that failure to follow this safety
statement could result in serious personal injury,
property or equipment damage.
CAUTION
Caution means that failure to follow this safety statement
may result in minor or moderate personal injury, property
or equipment damage.
• Use care when moving and handling the unit. Use gloves
to prevent personal injury from sharp edges.
• If your model requires defrosting, DO NOT use an ice
pick or other sharp instrument to help speed up
defrosting. These instruments can puncture the inner
lining or damage the cooling unit. DO NOT use any type
of heater to defrost. Using a heater to speed up
defrosting can cause personal injury and damage to the
inner lining.
IMPORTANT
• Do not lift unit by door handle.
• Never install or operate the unit behind closed doors.
Be sure front grille is free of obstruction. Obstructing
free airflow can cause the unit to malfunction and will
void the warranty.
• Failure to clean the condenser every six months can
cause the unit to malfunction. This could void the
warranty.
• Allow unit temperature to stabilize for 24 hours before
use.
• Do not Block any internal Fans
Use only genuine U-Line replacement parts. Imitation
parts can damage the unit, affect its operation or
performance and may void the warranty.
1
U-Line 3000 Series Product Features
Exterior Cleaning
3 Inspect & Plan
IMPORTANT
Stainless door panels, handles and frames can discolor
when exposed to chlorine gas, pool chemicals, salt water
or cleaners with bleach.
Product Registration
You have received a carton containing your 3000 series unit with a
package inside containing a Use and Care Guide and a Product
Registration Card. Please complete and mail the Product
Registration Card or register online at www.U-LineService.com.
Once your unit is installed, keep the Use and Care Guide and this
Installation Guide in a safe place for future reference.
• Keep your Stainless unit looking new by cleaning with a good
quality all-in-one stainless steel cleaner/polish on a monthly
basis. For best results use Claire Stainless Steel Polish and
Cleaner, which can be purchased from U-Line Corporation
(Part numbers 173348). Frequent cleaning will remove surface
contamination that could lead to rust. Some installations may
require cleaning on a weekly basis.
• Do not clean with steel wool or abrasive pads.
Product Description
• Do not use cleaners that are not specifically intended
for stainless steel on stainless surfaces (this includes
glass, tile and counter cleaners).
This installation guide covers the following models.
U-3018RGLOL-00
U-3024RGLS-00
U-3018RGLOL-01
U-3024RGLS-01
U-3018RGLS-00
U-3024RFOL-00
U-3018RGLS-01
U-3024RFOL-01
U-3018RGLS-13
U-3024RFS-00
U-3018RGLS-15
U-3024RFS-01
U-3018RFOL-00
U-3024WCOL-00
U-3018RFOL-01
U-3024WCOL-01
U-3018RFS-00
U-3024WCS-00
U-3018RFS-01
U-3024WCS-01
U-3018WCOL-00
U-3036RRGLOL-00
U-3018WCOL-01
U-3036RRGLS-00
U-3018WCS-00
U-3036RRGLS-13
U-3018WCS-01
U-3036BVWCOL-00
U-3018WCS-13
U-3036BVWCS-00
U-3018WCS-15
U-3036BVWCS-13
U-3024BEVOL-00
U-3036WCWCOL-00
U-3024BEVOL-01
U-3036WCWCS-00
U-3024BEVS-00
U-3036WCWCS-13
U-3024BEVS-01
U-3036RRS-00
U-3024RGLOL-00
U-3036RROL-00
• If any surface discolors or rust appears, clean it quickly with
Bon-Ami or Barkeepers Friend Cleanser and a non-abrasive
cloth. Always clean in the direction of the grain. Always finish
this process with Claire Stainless Steel Polish and Cleaner or
comparable product to prevent further problems.
• Glass surfaces may be cleaned with standard household window
cleaners.
WARNING
Rust that is allowed to linger can penetrate into the
surface of the stainless steel and complete removal of
the rust may not be possible.
U-3024RGLOL-01
Inspection
Unwrap and inspect the unit on a flat, level surface capable of
supporting its entire weight. If necessary, remove protective film
from Stainless Steel models.
U-Line Inspect & Plan
2
3024 Series
4 Prepare Site
Your U-Line product has been designed exclusively for a built-in
installation. When built-in, your unit does not require additional air
space for top, sides, or rear. However, the front grille must NOT
be obstructed and clearance is required for an electrical
connection in the rear.
Follow the cut-out drawing. The 23-7/8" width allows for ease in
installation and removal of the unit. 24" is the cabinet depth in
most installations.
IMPORTANT
• Unit can NOT be installed behind a closed cabinet door.
Electrical Specifications
24"
33-7/8"
to
34-7/8"
WARNING
SHOCK HAZARD — Electrical Grounding Required.
7"
4"
• Never remove the round grounding prong from the
plug and never use a two-prong grounding adapter.
• Never use an extension cord to connect power to the
unit.
IMPORTANT
Electrical installation must observe all state and local
codes. This unit requires connection to a grounded (threeprong), polarized receptacle that has been placed by a
qualified electrician.
The unit requires a grounded and polarized 115 VAC, 60 Hz, 15A
power supply (normal household current). An individual, properly
grounded branch circuit or circuit breaker is recommended. GFCI
(ground fault circuit interrupter) is usually not required for fixed
location appliances and is not recommended for your unit because
a GFCI could be prone to nuisance tripping. However, be sure to
consult your local codes.
See “Cut-Out Dimensions” for recommended receptacle location.
23-7/8"
3036 Series
Follow the cut-out drawing. The 35 11/16" width allows for ease in
installation and removal of the unit. 24" is the cabinet depth in
most installations.
24"
33-7/8"
to
34-7/8"
Cut-Out Dimensions
7"
4"
3018 Series
35 11/16"
Follow the cut-out drawing. The 18" width allows for ease in
installation and removal of the unit. 24" is the cabinet depth in
most installations.
33-7/8"
to
34-7/8"
24"
7"
4"
18"
U-Line Prepare Site
3
3018, 3024 & 3036 Series
5 Product Dimensions
3024 Series
3018 Series
3036 Series
22-11/16"
22-11/16"
33-11/16"
To
34-11/16"
33-11/16"
To
34-11/16"
4-3/4" To 5-3/4"
17-3/4"
22-11/16"
4-3/4" To 5-3/4"
33-11/16"
To
34-11/16"
23-5/8"
35-7/16"
4-3/4" To 5-3/4"
Glass & Solid Overlay
Glass & Solid Overlay
Glass & Solid Overlay
23-7/16"
23-7/16"
23-7/16"
33-11/16"
To
34-11/16"
33-11/16"
To
34-11/16"
33-11/16"
To
34-11/16"
3-5/8" To 4-5/8"
3-5/8" To 4-5/8"
23-5/8"
35-7/16"
3-5/8" To 4-5/8"
17-3/4"
Stainless Steel Glass Door
Stainless Steel Overlay Door
Stainless Steel Glass Door
23-7/16"
23-7/16"
23-7/16"
33-11/16"
To
34-11/16"
3-5/8" To 4-5/8"
17-3/4"
Stainless Steel Overlay Door
33-11/16"
To
34-11/16"
33-11/16"
To
34-11/16"
3-5/8" To 4-5/8"
23-5/8"
Stainless Steel Overlay Door
Product Dimensions
35-7/16"
3-5/8" To 4-5/8"
Stainless Steel Solid Door
4
Other Site Requirements
6 Door Swing Dimensions
Side-By-Side Installation
Units have a zero clearance for the door to open 90°. Overlay
models will need additional space for any knobs or pulls installed
on the overlay panel / frame. Stainless Steel models require 2"
door clearance to accommodate the handle if installed next to a
wall.
Wall
Cut-out width for a side-by-side installation is the total of the
widths listed under Cut-Out Dimensions in each unit’s Installation
Guide.
No trim kit is required. However, a 1/4-inch of space needs to be
maintained between the units to ensure unobstructed door swing.
Units must operate from separate, properly grounded electrical
receptacles placed according to each unit’s electrical specifications
requirements.
Power Supply
20 3/4"
The unit requires a grounded and polarized 115 VAC, 60 Hz, 15A
circuit (normal household current). See Electrical Specifications.
Environmental Requirements
The units are designed to operate between 50°F (10°C) and 100°F
(37°C). High ambient temperatures (100°F [37°C] or higher) may
reduce the unit’s ability to reach low temperatures.
20 1/8"
For best performance, keep the unit out of direct sunlight and away
from heat generating equipment.
In climates where high humidity and dew points are present,
condensation may appear on outside surfaces. This is considered
normal. The condensation will evaporate when the humidity drops.
90°
Door Swing
Space Required
For any Knobs or Pulls
Overlay
2" Min
Wall
20 3/4"
20 1/4"
90°
Door Swing
Stainless
U-Line Door Swing Dimensions
5
3. Gently pull bottom of wrap away from door.
7 3000 Series Doors
Door Alignment and Adjustment
4. The Wrap hinges on top of the door. Carefully pull wrap away
and then up. See below.
Align and adjust the door if it is not level, or is not sealing properly.
If the door is not sealed the unit may not cool properly, or
excessive frost or condensation may form in the interior.
Step 2
Door Top
IMPORTANT
Properly aligned, the door’s gasket should be firmly in
contact with the cabinet all the way around the door (no
gaps). Carefully examine the door’s gasket to assure that
it is firmly in contact with the cabinet. Also make sure the
door gasket is not pinched on the hinge side of the door.
WARNING
• Do not attempt to use the door to raise or pivot
your unit. This would put excessive stress on the
hinge system.
• Pay special attention to the Cable Arm. Make sure not
to over extend or damage it during door alignment.
Step 1
Stainless Models (Removing Wrap)
Door Bottom
1. Open door completely.
2. Remove the two wrap screws from the bottom of the stainless
steel door wrap.
Wrap Screws
5. If door being adjusted houses the
display unit, remove cable from
display by pressing in the release tab
on the cable connector.
Press Tab Down
Alignment and Adjustment
1. Using a T-25 Torx Bit, loosen each
pair of Torx head screws on both the upper and lower hinge
plate.
2. Square and align door as necessary.
3. Tighten Torx head screws on hinge.
Cable Arm
4. If necessary re-connect display and re-install stainless steel wrap.
T-25 Torx Screw
T-25 Torx Screw
U-Line 3000 Series Maintenance
6
8 3000 Series Overlays
IMPORTANT
Overlay / Frame Overlay Panel
IMPORTANT
•
The door panel must not weigh more than 20lbs.
•
It is important to ensure that all drilled holes are drilled to the
correct depth in order to avoid splits in the wood when
hardware is installed.
Appliance will need up to 34 1/2" to the under side of the
counter to leave room for leveling adjustments.
•
Due to differences in surrounding cabinetry the panel may
not perfectly align with door. The procedure below is
designed to provide a finished overlay panel that
seemlessly integrates with surrounding cabinetry.
Panel Preparation
A full overlay door panel completely covers the door frame and
provides a built-in appearance.
1. Cut the panels to the dimensions listed in the appropriate
diagram below.
2. Optional: Stain or Finish panel to desired stain or color. Be sure
to closely follow the instructions provided by the manufacturer.
IMPORTANT
If finishing frame overlay, both sides of overlay must be
finished in order to prevent warping.
3. Optional: Install handles and hardware.
Overlay & Frame Overlay Panel Dimensions
3018 and 3036 Series
BACK SURFACE MUST HAVE AMPLE FLAT SURFACE
TO MOUNT OVERLAY PANEL FLAT AND WITHOUT
INTERFERENCE
BACK SURFACE MUST HAVE AMPLE FLAT SURFACE
TO MOUNT OVERLAY FRAME FLAT AND WITHOUT
INTERFERENCE
3/4"
MIN
17 1/2"
3/4"
MIN
17 1/2"
2 3/4" Min
30"
Solid Overlay
30"
Frame Overlay
U-Line Door Panel Installation Guide
7
3024 Series
BACK SURFACE MUST HAVE AMPLE FLAT SURFACE
TO MOUNT OVERLAY PANEL FLAT AND WITHOUT
INTERFERENCE
3/4"
MIN
BACK SURFACE MUST HAVE AMPLE FLAT SURFACE
TO MOUNT OVERLAY FRAME FLAT AND WITHOUT
INTERFERENCE
23-1/2"
3/4"
MIN
23-1/2"
2 3/4" Min
30"
30"
Solid Overlay
Frame Overlay
Panel Installation
1. Fully open door,
2. Starting at corner, pull gasket
away from door.
3. Continue to pull gasket free
from gasket channel.
IMPORTANT
If working with the door that houses the display, make
certain the display cable remains securely seated in the
inner door channel, see below.
Inner
Display
Door Channel Cable
4. Upon removal, lay gasket
down on a flat surface.
U-Line Door Panel Installation Guide
8
5. The frame should be aligned with the outside edge (opposite the
hinge) and high enough to align with the highest point in the
door.
10. Be sure the screws force their way past the opening on the
gasket channel and sit flush against the bottom of the channel.
Align Top Of Panel With Highest Point Of Door
Align Frame
Against
Door Edge
First
Due to differences in floor construction or surrounding
cabinetry, the frame may not sit flush with the top of the
door.
Door
Overlay Panel
11. Remove clamps from door.
IMPORTANT
If frame requires additional adjustment after removing
clamps, slightly loosen each screw and adjust frame as
necessary. Tighten screws upon completion.
IMPORTANT
Frame
Overlay Panel
12. Starting at the corners, re-install the gasket into the gasket
channel in the frame. Make sure the gasket is fully seated. This
may take some force.
13. If installing an additional overlay on a 36" unit, repeat steps 1
through 12 on the opposite door.
Overlay Grille
The 3000 series grille is fully adjustable and can be set to match
your surrounding cabinetry dimensions. In addition to its
adjustability, an overlay may also be installed to truly provide a
seamless appearance.
6. Secure overlay to
door using clamps. A
robust tape may also
be used. U-Line
recommends the use
of bar clamps to
securely clamp the
overlay to the door. If
using tape, be certain
the tape will not
damage overlay finish
upon removal.
7. Using a 7/64" drill bit,
drill 6 pilot holes into
the wood panel
1/2" deep using the
holes in the door
frame as a guide.
8. Locate 6 of the #6x
1 1/2" screws
provided with your
unit
9. Using a phillips
screwdriver, place one
screw into each of the
6 pilot holes and
screw down. Do not
overtighten screws.
Preparing The Overlay
Bar
Clamp
1. Use the dimensions provided in the diagram on page 10 to cut
and shape your grille overlay. Recommended overlay thickness
is between 1/4" and 3/8". Dimension A will vary based on your
toe kick height.
2. Finish or stain your grille overlay to match your surrounding
cabinetry. Both sides require finishing to prevent warping. Be
certain to carefully follow the finish manufacturer’s
recommendations for application and cure times.
Door
Overlay
Panel / Frame
3. Apply double sided tape to the backside of the overlay grill. Use
the diagram below for reference. U-Line recommends 3M™
VHB™ tape, a high strength bonding tape.
Apply Tape To Shaded Area
Bar
Clamp
4. Remove backing paper from double sided tape.
5. Carefully align grille over overlay and press into position.
U-Line Door Panel Installation Guide
9
1-15/32"
1-15/32"
U-Line Door Panel Installation Guide
3036 Models
33-9/32"
35-7/32"
3024 Models
20-3/8"
23-9/16"
3018 Models
15-19/32"
17-17/32"
1"
1"
A
Dimension A may vary from a minimum of 3-1/4" to a maximum 4-1/4" depending on toe kick height.
Measure toe kick height and cut overlay to same dimension.
1-15/32"
Recommended Overlay Grille Thickness is 1/4" And May Not Exceed 3/8"
A
1"
A
Overlay Grille Dimensions
10
9 3000 Series Anti-Tip Bracket
Anti-Tip Brackets Installation
3036 Side Mount
Side mount configurations work well if you have a granite counter
top or do not wish to mount the brackets to the underside of your
counter top.
1. Align each bracket to the side mounting holes on your model
as shown below.
WARNING
The Anti-tip bracket must be installed to prevent the
unit from tipping when doors are fully opened, or
excess weight is placed on the front of the unit.
Left View Of Cabinet
Right View Of Cabinet
The Anti-tip brackets have multiple mounting options. Mounting
will depend on your particular cabinet configuration. Follow the
instructions below to secure your unit to your cabinet. Locate
your two Anti-tip brackets and 10 #8 x 5/8" screws included with
your unit.
3036 Top Mount
Top mount configurations work well with fully secured wood or
laminate counter tops.
1. Align the brackets on top of your unit as shown below. Both
brackets must be used to ensure a secure mount.
2. Using 4 of the supplied 10 #8 5/8" screws, install 2 screws into
each Anti-tip bracket, mounting the bracket to your unit.
3. Completely slide the unit into its position in the opening. Be
certain unit height is properly adjusted. (See Leveling
Information on pg. 13)
4. Open both doors completely to gain access to the Anti-tip
bracket. Make certain doors clear surrounding cabinetry.
2. Using 4 of the supplied 10 #8 5/8" screws, install 2 screws into
each plate using a #2 Phillips head screwdriver.
3. Completely slide the unit into its position in the opening. Be
certain unit height is properly adjusted. (See Leveling
Information on pg. 13)
5. Using a 3/32" drill bit, drill 6 pilot holes, 3 for each bracket, 5/8"
deep into cabinetry frame using the anti-tip bracket as a
template.
The 6 remaining cabinet side mounting screws will be installed
later in this guide.
4. Open both doors completely. Make certain doors clear
surrounding cabinetry.
5. Using a 3/32" drill bit drill 6 pilot holes, 3 for each bracket, 5/8"
deep into bottom of counter top. Use the Anti-tip brackets as a
template.
The 6 remaining cabinet side mounting screws will be installed
later in this guide.
U-Line 3000 Series Anti-tip Bracket Installation
11
3018/3024 Top Mount
3018/3024 Side Mount
Left View Of Cabinet
Right View Of Cabinet
Top mount configurations work well with fully secured wood or
laminate counter tops.
1. Align the brackets on top of your unit as shown below. Both
brackets must be used to ensure a secure mount.
2. Using 4 of the supplied 10 #8 5/8" screws, install 2 screws into
each plate using a #2 Phillips head screwdriver.
3. Completely slide the unit into its position in the cabinet. Be
certain unit height is properly adjusted. (See Leveling
Information on pg. 13)
4. Open both doors completely. Make certain doors clear
surrounding cabinetry.
5. Using a 3/32" drill bit, drill 6 pilot holes, 3 for each bracket, 5/8"
deep into bottom of counter top. Use the Anti-tip brackets as a
template.
The 6 remaining cabinet side mounting screws will be installed
later in this guide.
Side mount configurations work well if you have a granite counter
top or do not wish to mount the brackets to the underside of your
counter top.
1. Align each bracket to the side mounting holes on your model
as shown below.
2. Using 4 of the supplied 10 #8 5/8" screws, install 2 screws into
each Anti-tip bracket, mounting the bracket to your unit.
3. Completely slide the unit into its position in the opening. Be
certain unit height is properly adjusted. (See Leveling
Information on pg. 13)
4. Open door completely to gain access to the Anti-tip brackets.
Make certain door clears surrounding cabinetry.
5. Using a 3/32" drill bit, drill 6 pilot holes, 3 for each bracket, 5/8"
deep into cabinetry frame using the anti-tip bracket as a
template.
The 6 remaining cabinet side mounting screws will be installed later
in this guide.
U-Line 3000 Series Anti-tip Bracket Installation
12
Installation
10
10 Level & Install
1. Plug in the powercord.
Leveling Information
It is recommended that the unit is level once installed.
1. Use a level to check the levelness of the unit from front to back
and from side to
side. Level should be
placed along top
edge and side edge as
shown.
2. Gently push the unit into position. Be careful to not entangle the
electrical cord.
3. Re-check the leveling, from front to back and side to side. Make
any necessary adjustments. The unit’s top surface should be
approximately 1/8" below the countertop.
4. Install the 6 cabinet mounting screws for the Anti-tip bracket.
5. Remove the tape from the glass shelves and wipe out the inside
of the unit with a clean, water-dampened cloth.
Relocating the Shelves
The glass shelves can be moved to accommodate your bottles,
cans and containers.
Glass Shelves
• Open door fully, grasp shelf firmly, lift front edge slightly, and
pull straight out.
• Remove shelf tabs and reposition as necessary.
2. If the unit is not level,
remove grille and adjust feet as necessary. Use included tool to
adjust the height of the rear leveler feet. Turn screw clockwise to
raise the rear foot, counter-clockwise to lower.
• Reinsert shelf into cabinet and set down onto shelf tabs.
• All four shelf tabs must be set to the same height to properly
support the weight of the shelf.
Installation Troubleshooting
3. Check the levelness after each adjustment and repeat the
previous steps until the unit is level.
Q:
Problem
The door remains open unless it is pushed closed.
A:
Adjustment
Screw
Rear Level Foot
Adjustment
Screw
Rear Level Foot
Rotate Forward Feet to Adjust
INSTALLATION TIP
If the room floor is higher than the floor in the cut-out opening,
adjust the rear feet to achieve a total unit rear height of 1/8" less
than the opening’s rear height. Shorten the unit height in the front
by adjusting the front feet. This allows the unit to be gently tipped
into the opening. Readjust the front feet to level the unit after it is
correctly positioned in the opening.
Solution
The hinges should be self-closing when the door is open
approximately 8". If this is not the case, make sure nothing is
caught in the hinge closing mechanism. Also, re-check leveling from
front to back of the unit and readjust if necessary. Make sure that
pivot plate is installed correctly.
Q:
Problem
The custom overlay door was designed to align with the rest of the
cabinet doors, but the unit has crept forward.
A:
Solution
Make sure that the electrical cord is not obstructing the
installation.
Level & Install Unit
13
INSTALLATION GUIDE
®
SERVICE INFORMATION
If you have a problem with this appliance, your use and care guide has troubleshooting information to help you
quickly identify common problems and provide information on possible cause and remedy. Answers to
Customers Frequently Asked Questions are available at www.u-line.com/customer/faq.cfm. You may contact
U-Line directly:
GENERAL INQUIRIES:
SERVICE ASSISTANCE:
U-Line Corporation
P.O. Box 245040
Milwaukee, Wisconsin 53224-9540 U.S.A.
Phone (414) 354-0300
FAX (414) 354-7905
Email: sales@u-line.com
www.u-line.com
Phone (800) 779-2547
FAX (414) 354-5696
Email: onlineservice@u-line.com
www.u-lineservice.com
PARTS ASSISTANCE:
E-mail: onlineparts@u-line.com
BUILDING ON THREE GENERATIONS OF INNOVATION
For nearly five decades and three generations, U-Line continues to be the leader in innovation, quality and value
in the premium built-in undercounter ice making, refrigeration and wine preservation market. U-Line has
captivated those with an appreciation for the finer things with exceptional functionality, style, inspired
innovation and attention to even the smallest details. We are known and respected for our unwavering
dedication to product design, quality and selection.
In 1962, Henry Uihlein founded U-Line Corporation as an outgrowth of Ben-Hur Freezer Company and was
the first to develop and patent an automatic stand-alone undercounter residential ice maker. His foresight and
determination to develop new ideas and to succeed when there were no clear guidelines or solutions are
evident today. The newest Uihlein generation continues to build upon the family’s innovative legacy at the
Milwaukee, Wisconsin based business by providing continuity and vision from which new designs and
technology continue to be born.
Today the complete U-Line product collection includes Ice Makers, Wine Captain® Models, Combo® Models,
a Refrigerator / Freezer, Refrigerators, Drawers and Beverage Centers. The U-Line brand offers products in the
1000 Series, 2000 Series and the Modular 3000 Series. The 1000 Series offers a more targeted priced product
with appropriate features, while the 2000 Series offers upscale features, advanced technology and specialized
product families. U-Line’s approach to its breadth of products, multiple price points and features allows a choice
and product that will fit any lifestyle.
DESIGNED, ENGINEERED AND ASSEMBLED IN WISCONSIN, USA
The Built-In Undercouter Leader Since 1962
U-LINE.COM
©2009 U-Line Corporation
Publication Number 30253 02/2012 Rev H
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising