Fisher Paykel | RF135BDRUX4 | Surround Kit Installation | Fisher Paykel RF135BDRUX4 Surround Kit Installation

Fisher Paykel RF135BDRUX4 Surround Kit Installation
Installation instructions
Refrigerator Surround Kit
NZ AU GB AE HK SG IE US CA EU CN IN
E402B, E442B, E522B, RF610A, RF540, RF522A models
Important!
SAVE THESE INSTRUCTIONS
The model shown in this document may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our website
www.fisherpaykel.com or contact your local Fisher & Paykel dealer.
1
Refrigerator Surround Kit
2
This kit is designed to be used with models with a cabinet height of
between: 1695mm – 1806mm (66 ¾” – 71 1/8”) with curved or flat door styling.
You can find the part number for each installation type in Section 10.
3
4
5
Tools required (not included)
No. 2 drill bit – long
Electric drill
Phillips screwdriver
1 x 16mm (5/8 inch) piece of MDF the same size as the base of the cavity
(optional). Not needed if refrigerator cabinet is sitting directly on the floor
and not on raised toe kick area
Joiner kit (part number 819264) required if joining two refrigerators side by side
■■
■■
■■
■■
■■
Before starting
All dimensions are internal or cut out dimensions.
The refrigerator can be installed:
1. In a cavity with a toe kick under the product with the bottom trim fitted to the base (diagram 1b/5).
2. In a cavity with 16mm panel under the product with the bottom trim fitted to the panel
(diagram 1a/6).
3. In a cavity where the product is at floor level with no bottom trim (diagram 1a).
4. Check whether your fridge has hinges concealed by the front of the fridge door. If unsure refer to
page 2 note*** for instructions.
3
Check that the internal Cupboard Cavity dimensions are correct (see diagram 1a/b).
Unpack the refrigerator and/or freezer cabinets from their separate delivery cartons (see individual
cartons for unpacking procedures).
Ensure the floor and/or the cupboards are protected from damage during the unpacking and
assembly of the cabinets.
Check the refrigerator and freezer doors are hinged on the desired side.
Check that the kit is complete (refer to Parts Supplied in section 3).
1
2
To give the most integrated look, the kitchen cabinetry should be flush with
the front of the refrigerator door.
Getting Started
Note 1: Due to the size of the refrigerator cabinets, it is essential that assembly of the kit be undertaken
with a minimum of two able-bodied persons.
Note 2: It is important to include adequate venting to the top of the cabinet to ensure the efficient
operation of the refrigerator.
Note 3: The installation of the cabinet or cabinets can be at floor level as shown in diagram 1a or installed
above the toe kick board as in diagram 1b.
Note 4: Rollers and feet must be fitted.
Note 5: Cabinets installed above the toe kit should have a floor base constructed to support the total
weight of the loaded cabinet or cabinets placed on it.
The placement of the 16mm (5/8") MDF or plywood under the cabinet or cabinets on either installation
type is to allow the fitment of the bottom trim that covers it. It is optional.
Cabinetry Dimensions
4
Parts supplied
B
C1
Top trim (x 1)
B
E
E
C2
D
D
Side trim (x 2)
A
Bottom trim
(x 1)
A
Diagram 1a
Cabinet at floor level
Diagram 1b
Cabinet above toe kick
Diagram 1
Installation diagrams for illustration purposes only
Cutout dimensions – flush to edge of door (mm / inches)
Side trim centre
brackets (x 6)
SECURE Top
Trim Brackets
5
SECURE Side
trim brackets
6
Locate the ten side trim brackets.
For the Side By Side Refrigerator kits, one
bracket is to be screwed in the top centre of the
cabinet, secure the top bracket with two of the
screws (Type A, #8 x 12 Pozi Drive CSK).
Position five brackets to the left hand side of
the cabinet and the remaining five brackets to
the right hand side of the cabinet.
Looking at the front of the product, place the
top brackets on top of the wooden cabinet.
807 (31 13⁄16”)
852 (33 9⁄16”)
962 (37 7⁄8”)
1072 (42 1⁄4”)
1467 (57 3⁄4”)
1557 (61 5⁄16”)
1777 (70”)
B depth*
700 (27 9⁄16”)
700 (27 9⁄16”)
700 (27 9⁄16”)
700 (27 9⁄16”)
700 (27 9⁄16”)
700 (27 9⁄16”)
700 (27 9⁄16”)
C1 height** 1790 (70 1/2") 1790 (70 1/2") 1790 (70 1/2") 1875 (73 13/16") 1790 (70 1/2") 1790 (70 1/2") 1790 (70 1/2")
Locate the two/three top trim brackets.
For all other kits, the two brackets are to be
secured on either side, by two screws which are
mounted from the side (see diagram 2).
A width
790 (31 1/8") model
+ 790 (31 1/8") model
Washers
4 x 11 x 1mm
(x 2)
680 (26 3/4") model
+ 680 (26 3/4") model
Floor stops
P/no 460912
(x 2)
635 (25") model
+ 635 (25") model
Long screws
10 x 75 CSK PH
P/no SP0207
(x 2)
900 (35 7/16") model
Screw type A:
#8 x 12 Pozi
Drive CSK (x 26)
790 (31 1/8") model
or
Side trim
brackets (x 4)
635 (25") model
Top trim brackets:
– Single
refrigerator kits
(2 x brackets)
– Side by Side kits
(3 x brackets)
680 (26 3/4") model
Side trim
brackets (x 10)
Brackets should be evenly spaced down each
side (see diagram 3a/b). Secure each of these
brackets with the two screws provided.
Care must be taken to line up the front edge
of the brackets with the leading edges of
the cabinet.
Care must be taken to line up the top front
edge of the brackets with the leading edge of
the cabinet.
C2 height*** 1806 (71 1/8") 1806 (71 1/8") 1806 (71 1/8") 1891 (74 1/2") 1806 (71 1/8") 1806 (71 1/8") 1806 (71 1/8")
D
air vent
depth
200 (8”)
200 (8”)
200 (8”)
200 (8”)
200 (8”)
200 (8”)
200 (8”)
E
air vent
width
502 (19 13/16")
547 (21 9⁄16")
657 (25 7/8")
767 (30 1/4")
1162 (45 3⁄4")
1252 (49 5⁄16")
1472 (58")
* Depth is a minimum requirement
** Height is without 16mm MDF packer
*** Height is with 16mm MDF packer
Cut out dimensions above are to be used as minimum dimensions.
7
SECURE Floor Stops
Two floor stops are supplied to prevent the refrigerator from being pushed too far back into the cavity.
These are mounted on the base or floor at a distances of 688mm (27") from the face front edge of the
trim kit.
Hint: Holes should be drilled in the centre of
the slot in the brackets to allow for adjustment.
Diagram 3a
or
150 mm
688 mm
End bracket
Centre bracket
Diagram 2
Diagram 3b
Diagram 4
8
TRIM INSTALLATION
9
The bottom trim is designed to cover the front edge of the
floor base panel of the cabinet. This trim can be installed
on a raised toe kick (diagram 1a) or toe kick below the
refrigerator (diagram 1b)
If installing two refrigerators/
freezers side by side a joiner
kit is required. Refer to these
instructions and fit joiner kit
before pushing refrigerator into
place, see diagram 6.
16mm (5/8 inch)
plywood or MDF
board insert
Remembering that if this trim is to be used with the
refrigerator at floor level the cut out dimensions will need
to have 16mm (5/8") added to its height to allow for the
bottom trim to be fitted. Note this trim is optional on this Part of base
type of installation. If used with a raised toe kick the 16mm
packer should be part of the base (diagram 5). Therefore
16mm is not required to be added to the height dimension.
Plug refrigerator into electrical
socket, run water connection
to refrigerator if required
(Ice & Water models only).
Optional
Gently install refrigerator into
cabinetry making sure it is
centred within the surround trim.
1. If used place the 16mm (5/8") piece of plywood or
with bottom trim fitted into the cavity (diagram 5 or 6).
Note the piece should be the same size as the base of
the cavity.
The front of the refrigerator
door should be flush with the
front of the cabinetry to obtain
an integrated look.
2. Remove protective coating film from surround trim.
3. To install the surrounds, first clip in the top surround.
Ensure the locator strips at the rear of the top brackets clip
into the rear of the top trim.
Ensure the front leveling feet are
adjusted to take the load of the
fridge and keep it in place.
4. Clip both side trims into place starting from the front
cabinet edge.
10
MOVE INTO CAVITY
Diagram 6
Diagram 5
Kit part numbers and cut out dimensions table
Kit Part Numbers
Plus
Brushed
Joiner
Stainless
Kit
23980
Refrigerator Model
1 x 635
(25")
LH
807
23981
1790mm
27 9/16”
70 1/2”
1 x 790
(31 1/8")
LH
807mm
700mm
1790mm
31 13⁄16”
27 9/16”
70 1/2”
1 x 790
(31 1/8")
RH
819264
1467mm
700mm
1790mm
57 3/4”
27 9/16”
70 1/2”
700mm
1790mm
33 9⁄16”
27 9/16”
70 1/2”
1 x 900
(35 7/16")
(French door
model)
852mm
700mm
1790mm
33 9⁄16”
27 9/16”
70 1/2”
1 x 790
(31 1/8")
(French door
model)
819264
1557mm
700mm
1790mm
61 5/16”
27 9/16”
70 1/2”
23990
962
1790
680
700mm
1790mm
37 7/8”
27 9/16”
70 1/2”
962mm
700mm
1790mm
37 7/8”
27 9/16”
70 1/2”
1777mm
700mm
1790mm
70”
27 9/16”
70 1/2”
1072mm
700mm
1875mm
42 ¼”
27 9/16”
73 13/16”
962mm
700mm
1790mm
37 7/8”
27 9/16”
70 1/2”
* Depth is a minimum requirement
** Height is without 16mm MDF packer
*** For refrigerators / freezers where the hinge is not concealed
by the door refer to spare parts for the correct kit number.
820413 D should list non concealed number kit.
680
962mm
1790
1790
23985
819264
23989
1072
790
1557
Height
C**
1875
1790
23984
680
790
900
852
Depth
B*
1790
852mm
23988
1777
790
23983
680
23987
962
2 x 790
(31 1/8")
1790
635
962
Width
A
1790
23982
852
2 x 680
(26 3/4")
700mm
31 13⁄16”
790
1467
635
1 x 680
(26 3/4")
RH
807mm
Refrigerator Model
1790
635
1 x 680
(26 3/4")
LH
Height
C**
790
807
2 x 635
(25")
Depth
B*
Cut Out Dimensions
1790
1 x 635
(25")
RH
Width
A
1790
635
Kit Part Numbers
Plus
Brushed
Joiner
Stainless
Kit
23986
Cut Out Dimensions
Concealed Hinge
Non Concealed Hinge
Before you call for service or assistance ...
Check the things you can do yourself. Refer to the installation instructions, your User Guide – in particular
the troubleshooting section and check that:
1
2
your product is correctly installed.
you are familiar with its normal operation.
If after checking these points you still need assistance or parts, use the link at
www.fisherpaykel.com for regional service providers.
839254 A NZ AU GB AE HK SG IE US CA EU CN IN 09.13
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising