MicroFridge 20160 Instruction Manual

MicroFridge 20160 Instruction Manual
When you start this refrigerator from the Microwave Oven Power Supply: Do NOT plug in while the Microwave
Oven is working. WAIT at least three (3) minutes after using the Microwave Oven before plugging in the
refrigerator because the electricity will be cut off during this period.
UNLESS THE ABOVE GROUNDING METHOD IS FOLLOWED, YOU ARE NOT PROTECTED AGAINST
SEVERE OR LETHAL SHOCK IN THE EVENT OF A SHORT CIRCUIT OF AN ELECTRICAL COMPONENT
OR WIRING OF THE REFRIGERATOR.
Use a 3-prong plug with the 3-prong grounded outlet on the Microwave Oven. (This is the only method that
complies with the National Electric Code, local codes and ordinances.)
Do not operate your refrigerator near flammable materials such as gasoline. Do not use for storage of
flammable materials. Your refrigerator must be grounded. Use a 120 volt, 60 Hz outlet. If you are using
this refrigerator as part of a MicroFridge® with Safe Plug® combination appliance, you must use the
120 V/60 Hz outlet located on the back of the Microwave Oven in order to take advantage of patentpending Safe Plug® technology to limit electrical draw. Do not use an extension cord.
If your oven does not operate properly, unplug it from the 120 volt household outlet
and then plug it back in. This unit is not designed for 50 Hz or any circuit other than
120 volt/ 60Hz AC current.
The MicroFridge® with Safe Plug® brand refrigerator and charging outlets will not
operate when the oven is on. This is part of the patent-pending MicroFridge® with
Safe Plug® technology that prevents wiring overload.
NOTE:
CAUTION:
The MicroFridge® with Safe Plug® combination appliance will now operate with eleven
(11) - fifteen (15) amps of current draw.
4.8MFR
•
3. Plug refrigerator into the socket
provided in the rear of the microwave
oven.
•
⑩
④
②
⑥
⑦
Screws can be found in the
attached bag.
2. Attach the microwave oven to the
refrigerator by screwing in the four (4)
side screws and one (1) rear screw.
Do not remove the feet from the
bottom of the oven.
•
Do not block the inlet and outlet
openings located at the rear and
bottom of the oven. Blocking the
inlet and/or outlet openings can
damage the oven.
•
⑫
⑪
The socket is intended for use with approved MicroFridge® with Safe Plug®
refrigerators. Use of this socket for other appliances may be hazardous.
1. Place the oven on top of the
approved MicroFridge® with Safe
Plug® refrigerator carefully lining up
screw holes of the refrigerator sash
with microwave side holes.
⑨
Remove all packing materials and
accessories. Examine the oven for any
damage, such as dents or broken door.
Do not install if the oven is damaged.
⑤
①
⑧ ③
Installation of Microwave Models
− Microwave oven magnetron
− Refrigerator/freezer sealed system and compressor
− Microwave oven and refrigerator/freezer mechanical components
2 years
Parts and Features
MicroFridge® with Safe Plug®
Assembly Diagram - Model 4.8MFR
Duration
1.
Discharge Outlet for Refrigerated Air: Since cold air flows through this outlet into the
refrigerator, be sure to avoid blocking it with stored food.
Suction Inlet
Temperature Control
Slide Out Shelves
Freezer Shelf
Interior Light
Interior Light Switch
Ice Cube Tray
Full-Width Door Shelves
2-Liter Door Shelf
Glass Shelf with Crisper
Adjustable Feet
Intirion is pleased to provide a comprehensive warranty on these products. Intirion takes
pride in its product and manufacturing standards and warrants its products and parts
against defects in materials or workmanship to the original purchaser.
Subassembly
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
4. Plug your oven into a standard 120-volt/60Hz household outlet. Be sure the
electrical circuit is at least fifteen (15) amperes and that your microwave oven is the
only appliance on the circuit.
MicroFridge® with Safe Plug®, a Product of Intirion Corporation
Microwave Oven and Refrigerator/Freezer Residential Limited Warranty
INSTRUCTION
MANUAL
4.8MFR
by Intirion
REFRIGERATOR/FREEZER
2 years
1 year
All requests for service should be directed to Customer Service at Intirion by calling
1-800-637-7567. Intirion offers a quick response customer service program. Customer
Service will diagnose the problem and either replace or the original purchaser will carryin the appliance to an authorized service provider for repair, at the discretion of
Intirion.
MicroFridge® with Safe Plug® warranty services are performed by Intirion authorized
service providers. Intirion expects prompt, courteous and efficient service. Intirion
further expects that all authorized service providers will make every reasonable effort
to enhance the image and reputation of Intirion and its products. Inadequate service or
customer dissatisfaction should be promptly reported to Intirion.
Damage initiated by spark fires caused by using inappropriate material inside the
microwave oven is specifically excluded from this warranty. Intirion assumes no liability
and does not guarantee or warranty any repairs and/or replacement parts not supplied
or performed by an authorized service provider, nor any 50/60 cycle or 60/50 cycle
conversions, damage caused by failure to follow the owner’s manual as to adjustments
and/or maintenance, customer adjustments that are not covered in the instruction
booklet, broken or marred cabinet, misuse, neglect, accident, fire, flood or other acts of
nature.
THIS WARRANTY WILL BECOME INVALID IF ANY SERIAL NUMBER ON THE
PRODUCT IS ALTERED, REPLACED, DEFACED OR MISSING. THIS WARRANTY IS
FOR INTIRION PRODUCTS PURCHASED AND USED IN THE UNITED STATES
EXCEPT FOR UNITED STATES POSSESSIONS AND/OR DOMINIONS OF THE
UNITED STATES.
This is the entire Intirion warranty and it may not be changed or amended by any
person, agency, distributor, dealer, or company. Intirion assumes no liability and indeed
specifically denies responsibility for any consequential damages beyond the repair or
replacement of the product or its components.
What is Safe Plug® Technology?
MicroFridge® combination appliances utilize Safe Plug® technology, a revolutionary,
patent-pending design, to conserve electricity and reduce potential fire hazards that can be caused
by overloaded circuits. This technology, built into the microwave, works by temporarily shutting off
the power to the refrigerator and charging outlets when the microwave is in use. When the
microwave is finished, power to the refrigerator and charging outlets resumes. Engineered with
unique one-plug-to-the-wall operation, our combination appliances never draw more than
11-15 amps of current.
MicroFridge® with Safe Plug® uses patent-pending intelligent load monitoring technology to control
the microwave, refrigerator and extra outlets. The two charging outlets are designed to
conveniently re-charge cell phones, digital cameras, laptops or similar low power devices.
The warranty period begins on the date of sale and proof of that date (evidenced by an
original sales slip or bill of sale) will be necessary to initiate a warranty claim.
ATTENTION
MICROFRIDGE® WITH SAFE PLUG®, A PRODUCT OF INTIRION CORPORATION,
10 Walpole Park South, Walpole MA 02081 1-800-637-7567
For your protection in the event of theft or loss of
refrigerator, fill in spaces provided below.
Model and Serial Numbers are indicated on the
inside right liner of the refrigerator.
MODEL No. ____________________________
Part No. 8336460132800
SR4886/87MF*
SERIAL No. ____________________________
Printed in Mexico
Where to Place Your MicroFridge® with Safe Plug®
Temperature Control
1. Select a location with a strong, level floor. If the
floor is not quite level, adjust the height of the front
legs accordingly.
2. Allow four inches of space between the refrigerator’s
back and the wall, one inch above the refrigerator
and one inch on the side.
3. Avoid any direct sunlight and heat. Direct sunlight
may affect the enamel coating. Heat sources
nearby will cause higher electricity consumption.
4. Avoid very moist places. Too much moisture in the
air will cause frost to form very quickly on the
evaporator and the refrigerator will have to be
defrosted more frequently.
5. Your refrigerator is equipped with a three-prong plug
and is grounded to eliminate electrical hazards. In order to make it more
effective, it must be plugged into a grounded electrical outlet.
6. Plug your refrigerator in the back of the microwave.
You can Control the temperature inside your refrigerator by turning the temperature
control dial. Higher numbers mean greater cooling power, smaller numbers mean less
cooling power.
Test Run Your Refrigerator
Before using your refrigerator, clean it and test run it to see if it is operating
properly. If it is not, then check your electrical source. If you cannot locate the
source of the problem, contact your dealer.
1. Set the temperature control knob to the “OFF” position and then plug the AC
cord into an electrical outlet of 115 volt, 60Hz. The compressor motor should
not run.
2. Set the temperature control knob to the “MAX” position and let the
refrigerator operate for 20 minutes. The freezer should get slightly frosted
and the motor should run smoothly with a soft hum.
3. Rotate the temperature control knob counter-clockwise toward the “MIN”
position. Before the pointer of the temperature control knob reaches the
“MIN” position, the compressor motor should turn off.
Sound of Flowing Is Noticeable
Refrigerator
Set the temperature control dial to 3 for optimum
refrigeration effects under normal conditions. Set the
temperature control dial to MAX only when the rapid
refrigeration in your refrigerator is necessary. Be sure
to set it back to 3 later on.
Freezer
For ordinary use, set the temperature control in
the “MED” position. For rapid freezing of
foodstuffs or to make ice cubes in a hurry, set the
knob to the “COLD” position. Do not forget to set
the temperature control back to “MED” once the
rapid freezing process has been completed.
Important
−
Do not operate your refrigerator for more than six hours at a stretch with the
temperature control dial set to 5 or MAX. At this setting, the compressor
will run continuously. Consequently, foodstuffs stored in the refrigerator
compartment will be frozen and frost will form on the cooling (evaporator)
unit.
−
At the control dial setting of MIN, the freezer compartment temperature will
not remain at a sufficiently low level for ice cream and frozen foods.
Usually the cold control knob should be set at middle position.
This sound is caused by the refrigerant flowing into the refrigerating device. It
does not denote a malfunction.
How to Remove Ice Cubes from the Tray
The ice cube tray is flexible. Twist the tray to remove the
ice cubes. If the ice cube tray is frozen hard to the surface,
do not use a knife or other metal instrument to remove it
because this may damage the surface.
ATTENTION
If the unit is turned off or unplugged., YOU MUST ALLOW THREE (3) MINUTES BEFORE
RESTARTING OR REPLUGGING THE UNIT. The unit will not start if you attempt to restart it in
less than three (3) minutes.
Cleaning and Maintenance
Changing Door Hinge Location
Your refrigerator does not require any maintenance.
Turn off your refrigerator and remove all food, shelves, trays, etc. Wash
the interior liner with a solution of two tablespoons of baking soda and a
quart of warm water. Then, rinse and wipe it out. Do not use soaps,
detergents, scouring powders, spray cleaners or the like for cleaning the
interior liner. It may cause odors in the refrigerator compartment.
Wash the ice cube trays, drip tray and shelves in a mild detergent solution
and dry with a soft cloth.
Wipe the exterior surface with a soft cloth dampened with soapy water
and dry it with a soft cloth. Normal appliance spray cleaners may be used
for the exterior only.
Use only mild soap and water to clean the door gasket.
Never use acid, chemical thinners, gasoline, benzene or the like to clean
any part of the refrigerator. Boiling water and benzene may deform or
damage the plastic parts.
The door of the refrigerator can be hinged on either side
so that the direction they open in can be chosen to suit
the place of installation. Refer to the disassembly
diagram and change the door hinges according to the
following steps:
1. Remove the hinge cap by twisting it off.
2. Remove the upper hexagonal head screws.
The freezer door can now be removed.
3. Remove the middle hexagonal head screws. The
refrigerator door can now be removed.
4. Remove the hinge side leg, attach it to the leg hole
on the opposite side.
5. Remove the other leg, attach it to the leg hole on the
opposite side.
6. Attach the bottom hinge symmetrically to the other
side of the cabinet.
7. Remove the upper hinge plug buttons and insert
them in the holes from which the screws were
removed in Step 2.
8. Remove the middle hinge plastic cover and remount it to cover the holes from which the screws
were removed in Step 3.
9. Remove the plug button from each door using a screwdriver and insert in the hole on the
opposite side of each door.
10. Attach the refrigerator door to the bottom hinge.
Cleaning the Evaporating Tray
Since dust accumulated on the evaporating tray
will decrease the evaporation efficiency, remove
the tray to clean.
The evaporating tray is set on refrigerator back.
To remove, pull it away from the unit. After
cleaning make sure to put the tray securely back
in place otherwise defrosted water may spill or
the evaporation process maybe hindered.
Hot-Line
With the freezer-refrigerator in operation, it is possible that the
cabinet will feel warm at the front edges. This does not
indicate trouble. It is attributable to the hot gas line design.
This prevents moisture from accumulating and has nothing to
do with the storage temperature inside.
11. Rotate the middle hinge 180 degrees. Attach it
to the refrigerator door and secure it with a
screw. (Do not tighten the screw completely.)
Installing the Hinge Clip
12. Attach the upper hinge to the freezer door. Attach
the freezer to the middle hinge and use the screw
to attach the upper hinge. (Do not tighten the
screw completely.)
13. The direction in which the doors open has now
been changed; however, the following points
should be checked:
A) Make sure both doors are on straight.
B) Make sure that there is no space between the door
gasket and the refrigerator unit itself when the doors
are closed.
C) Make sure that the gasket on the hinged side is not
caught between the door and the unit when the door is
opened or closed. (If the door is forced closed when
the gasket is caught, the gasket may be damaged.)
14. After making sure that the doors are installed
correctly, tighten all the screws holding the hinges.
If they are not tightened, the doors may slip out of
position or there may be an opening between the
doors and the cabinet.
15. For models with senior living handles, remove the
screws holding the handle on the door. Remove
plastic pins from the other side of the door and
insert them into the holes where the screws were
removed. Re-install the handle using the same
screws that were removed from the door handles.
WARNING:
Do not route high-voltage electrical cords
underneath the hinge clip. Only use the clip
to cover low-voltage electrical cords.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement