MicroFridge | 3.0LMF4RHW | Instruction manual | MicroFridge 3.0LMF4RHW Instruction Manual

Consult a qualified electrician if the grounding instructions are not completely understood, or if doubt exists as
to whether the appliance is properly grounded.
When you start this refrigerator from the Microwave Oven Power Supply: Do NOT plug in while the Microwave
Oven is working. WAIT at least three (3) minutes after using the Microwave Oven before plugging in the
refrigerator because the electricity will be cut off during this period.
UNLESS THE ABOVE GROUNDING METHOD IS FOLLOWED, YOU ARE NOT PROTECTED AGAINST
SEVERE OR LETHAL SHOCK IN THE EVENT OF A SHORT CIRCUIT OF AN ELECTRICAL COMPONENT
OR WIRING OF THE REFRIGERATOR.
If your oven does not operate properly, unplug it from the 115 volt household outlet
and then plug it back in. This unit is not designed for 50 Hz or any circuit other than
115 volt/ 60Hz AC current.
The MicroFridge® with Safe Plug® brand refrigerator and charging outlets will not
operate when the oven is on. This is part of the patented MicroFridge® with Safe
Plug® technology that prevents wiring overload.
NOTE:
Use a 3-prong plug with the 3-prong grounded outlet on the Microwave Oven. (This is the only method that
complies with the National Electric Code, local codes and ordinances.)
Do not operate your refrigerator near flammable materials such as gasoline. Do not use for storage of
flammable materials. Your refrigerator must be grounded. Use a 115 volt, 60 Hz outlet. If you are using
this refrigerator as part of a MicroFridge® with Safe Plug® combination appliance, you must use the
115 V/60 Hz outlet located on the back of the Microwave Oven in order to take advantage of patentpending Safe Plug® technology to limit electrical draw. Do not splice cord. Do not use an extension
cord.
CAUTION:
Freezer
Ice Cube Tray
Please ensure that component parts shall be
Wire Shelf
replaced with like components and that
Glass Shelf
servicing shall be done by factory authorized
Crisper
service personnel, so as to minimize the risk
of possible ignition due to incorrect parts or
Adjustable Feet
improper service.
Temperature Control Knob
Small Item Rack
2-Liter Door Shelf
Evaporating Tray (on rear bottom of unit)
Ice Scraper
3.0MF4R
⑥
⑩
⑦
③
⑧
②
①

The socket is intended for use with approved MicroFridge® with Safe Plug®
refrigerators. Use of this socket for other appliances may be hazardous.
3. Plug refrigerator into the socket
provided in the rear of the microwave
oven.

Screws can be found in the
attached bag.
2. Attach the microwave oven to the
refrigerator by screwing in the four (4)
side screws and one (1) rear screw.
Do not remove the feet from the
bottom of the oven.

Do not block the inlet and outlet
openings located at the rear and
bottom of the oven. Blocking the
inlet and/or outlet openings can
damage the oven.

⑨
⑤
④
4. Plug your oven into a standard 115-volt/60Hz household outlet. Be sure the
electrical circuit is at least fifteen (15) amperes and that your microwave oven is the
only appliance on the circuit.
1. Place the oven on top of the
approved MicroFridge® with Safe
Plug® refrigerator carefully lining up
screw holes of the refrigerator sash
with microwave side holes.
Remove all packing materials and
accessories. Examine the oven for any
damage, such as dents or broken door.
Do not install if the oven is damaged.
⑪
MicroFridge® with Safe Plug®
Assembly Diagram - Model 3.0MF4R
Installation of Microwave Models
Subassembly
Duration
 Microwave oven magnetron
 Refrigerator/freezer sealed system and compressor
 Microwave oven and refrigerator/freezer mechanical components
2 years
Parts and Features
INTIRION, a division of Danby Limited, is pleased to provide a comprehensive warranty on
these products. INTIRION takes pride in its product and manufacturing standards and
warrants its products and parts against defects in materials or workmanship to the original
purchaser.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
The MicroFridge® with Safe Plug® combination appliance will now operate with eleven
(11) - fifteen (15) amps of current draw.
MicroFridge® with Safe Plug®, a Product of INTIRION™ Corporation
Microwave Oven and Refrigerator/Freezer Residential Limited Warranty
INSTRUCTION
MANUAL
3.0MF4R
by INTIRION
REFRIGERATOR/FREEZER
2 years
1 year
All requests for service should be directed to Customer Service at INTIRION by calling 1800-637-7567 if you are located in the U.S., and 1-800-263-2629 if you are located in
Canada. INTIRION offers a quick response customer service program. Customer service
will diagnose the problem and either replace or the original purchaser will carry-in the
appliance to an authorized service provider for repair, at the discretion of INTIRION.
MicroFridge® with Safe Plug® warranty services are performed by INTIRION authorized
service providers. INTIRION expects prompt, courteous and efficient service. INTIRION
further expects that all authorized service providers will make every reasonable effort to
enhance the image and reputation of INTIRION and its products. Inadequate service or
customer dissatisfaction should be promptly reported to INTIRION.
Damage initiated by spark fires caused by using inappropriate material inside the
microwave oven is specifically excluded from this warranty. INTIRION assumes no liability
and does not guarantee or warrant any repairs and/or replacement parts not supplied or
performed by an authorized service provider, nor any 50/60 cycle or 60/50 cycle
conversions, damage caused by failure to follow the owner’s manual as to adjustments
and/or maintenance, customer adjustments that are not covered in the instruction booklet,
broken or marred cabinet, misuse, neglect, accident, fire, flood or other acts of nature.
THIS WARRANTY WILL BECOME INVALID IF ANY SERIAL NUMBER ON THE
PRODUCT IS ALTERED, REPLACED, DEFACED OR MISSING. THIS WARRANTY IS
FOR INTIRION PRODUCTS PURCHASED AND USED IN THE UNITED STATES AND
CANADA EXCEPT FOR UNITED STATES POSSESSIONS AND/OR DOMINIONS OF
THE UNITED STATES.
This is the entire INTIRION warranty and it may not be changed or amended by any
person, agency, distributor, dealer, or company. INTIRION assumes no liability and indeed
specifically denies responsibility for any consequential damages beyond the repair or
replacement of the product or its components.
The warranty period begins on the date of sale and proof of that date (evidenced by an
original sales slip or bill of sale) will be necessary to initiate a warranty claim.
MICROFRIDGE® WITH SAFE PLUG® A PRODUCT OF INTIRION CORPORATION, A
DIVISION OF DANBY PRODUCTS LIMITED
2 Annette Road, Suite 3, Foxborough, MA 02035
1-800-637-7567 U.S. Customers
PO Box 1778, Guelph, Ontario, Canada N1H 6Z9 1-800-263-2629 Canada Customers
Part No. 8336460122000
PR2970MF*
What is Safe Plug® Technology?
MicroFridge® with Safe Plug® combination appliances utilize Safe Plug® technology, a
revolutionary, patented design, to conserve electricity and reduce potential fire hazards that can be
caused by overloaded circuits. This technology, built into the microwave, works by temporarily
shutting off the power to the refrigerator and charging outlets when the microwave is in use. When
the microwave is finished, power to the refrigerator and charging outlets resumes. Engineered with
unique one-plug-to-the-wall operation, our combination appliances never draw more than 11-15
amps of current.
MicroFridge® with Safe Plug® uses patented intelligent load monitoring technology to control the
microwave, refrigerator and extra outlets. The two charging outlets are designed to conveniently recharge smart phones, tablets, laptops or similar low power devices.
IMPORTANT WARNING
An empty refrigerator is a very dangerous attraction
to children. Remove the gasket, latches, lids or
doors from unused appliances, or take some other
action that will guarantee the appliance harmless.
DANGER: Risk of child entrapment. Before you
throw away your old refrigerator:
• Take off the doors.
• Leave the shelves in place so that children may
not easily climb in.
DON’T WAIT! DO IT NOW!
Printed in Mexico
ATTENTION
For your protection in the event of theft
or loss of refrigerator, fill in spaces
provided below.
Model and Serial Numbers are
indicated on the inside right liner of the
refrigerator.
MODEL No. ___________________
SERIAL No.
21.07.2014
Where to Place Your MicroFridge® with Safe Plug®
Temperature Control
1. This product is designed for free-standing installation only.
2. Select a location with a strong level floor. If the floor is not quite level, adjust the
height of the front legs accordingly. Do not place anything under either one of the
front legs or the rear of the unit.
3. A minimum of 2 inches of clearance must be provided
between the rear condenser and the wall. Providing
greater rear wall clearance when space allows in order to
improve air circulation is recommended; in addition, leave
unobstructed space above the refrigerator and both sides.
4. Avoid any direct sunlight and heat. Direct sunlight may
affect the enamel coating. Heat sources nearby will cause
higher electricity consumption.
5. Avoid very moist places. Too much moisture in the air will cause frost to form
very quickly on the evaporator and the refrigerator will have to be defrosted more
frequently.
6. Your refrigerator is equipped with a three-prong plug and is grounded to
eliminate electrical hazards. In order to make it more effective, it must be plugged
into a grounded electrical outlet.
7. Plug your refrigerator into the back of the microwave.
You can Control the temperature inside your refrigerator by turning the
thermostat dial. Higher numbers mean greater cooling power, smaller numbers
mean less cooling power. Set the temperature control dial to 3 for optimum
refrigeration/freezing effects under normal conditions. Set the temperature
control dials to MAX only when the rapid refrigeration/freezing of foodstuffs in
your refrigerator is necessary. Be sure to set it back to 3 later on.
Test Run Your Refrigerator
We urge you to read the chart below. If the problem is not caused by defective
workmanship or materials, you may be charged for service calls even during the
warranty period. Before calling for service, check these few simple points:
Before using your refrigerator, clean it and test run it to see if it is operating
properly. If it is not, then check your electrical source. If you cannot locate the
source of the problem, contact your dealer.
1. Set the temperature control knob to the OFF position and then plug the AC cord
into an electrical outlet of 115 volt, 60Hz. The compressor motor should not run.
2. Set the temperature control knob to the MAX position and let the refrigerator
operate for 20 minutes. The freezer should get slightly frosted and the motor
should run smoothly with a soft hum.
3. Rotate the temperature control knob counter-clockwise toward the MIN position.
Before the pointer of the temperature control knob reaches the MIN position, the
compressor motor should turn off.
NOTE: The refrigerator will not operate when timer of microwave oven is
on. This is part of the patented MicroFridge® with Safe Plug® technology
that prevents wiring overloads.
Sound of Flowing is Noticeable
Important


Do not operate your refrigerator for more than six hours at
a stretch with the temperature control dial set to 5 or MAX.
At this setting, the compressor will run continuously.
Consequently, foodstuffs stored in the refrigerator
compartment will be frozen and frost will form on the
cooling (evaporator) unit.
At the control dial setting of 1 the freezer compartment temperature will not
remain at a sufficiently low level for ice cream and frozen foods.
Before Calling for Service
Refrigerator
not operating
 Is the temperature control dial inside the refrigerator set to OFF?
 Is the unit unplugged? Be sure!
 Is the fuse blown or the circuit breaker tripped?





Has the door been opened frequently? Is it slightly ajar?
Storage
compartment
too warm





Is the refrigerator level? (Try to rock it.)
Excessive
noise
This sound is caused by the refrigerant flowing into the refrigerating device. It does
not denote a malfunction.
How to Remove Ice Cubes from the Tray
The ice cube tray is flexible. Twist the tray to remove the ice
cubes. If the ice cube tray is frozen hard to the surface, do not
use a knife or other metal instrument to remove it because this
may damage the surface.
Moisture
Are the shelves overcrowded?
Have large amounts of warm food been added recently?
Are the coils on the back clogged or blocked?
Is the temperature control dial set properly?
Are dishes vibrating?
Are there objects behind or on top that are shaking?
Does any part of the refrigerator touch the back or side wall?
When the motor comes on, you may hear popping or cracking sounds as
metals expand or contract.
 Moisture in the storage compartment is normal in humid weather.
 Is the door opened frequently? Has the door been left ajar?
Does the door fit properly?
Cleaning and Maintenance
Changing Door Hinge Location
Your refrigerator does not require any maintenance.
Turn off your refrigerator and remove all food, shelves, trays, etc. Wash the
interior liner with a solution of two tablespoons of baking soda and a quart of
warm water. Then, rinse and wipe it out. Do not use soaps, detergents,
scouring powders, spray cleaners or the like for cleaning
the interior liner. It may cause odors in the refrigerator
compartment.
Wash the ice cube trays, drip tray and shelves in a mild
detergent solution and dry with a soft cloth. Normal
appliance spray cleaners may be used for the exterior
only.
Use only mild soap and water to clean the door gasket.
Never use acid, chemical thinners, gasoline, benzene
or the like to clean any part of the refrigerator. Boiling
water and benzene may deform or damage the plastic
parts.
The door of the refrigerator can be hinged on either
side so that the direction they open in can be chosen to
suit the place of installation. Refer to the disassembly
diagram and change the door hinges according to the
following steps:
Cleaning the Evaporating Tray
Since dust accumulated on the evaporating tray will
decrease the evaporation efficiency, remove the tray
to clean.
The evaporating tray is set on the back of the
refrigerator. To remove, pull it away from the unit.
After cleaning make sure to put the tray securely
back in place otherwise defrosted water may spill or
the evaporation process may be hindered.
Hot-Line
With the refrigerator/freezer in operation, it is possible that the
cabinet will feel warm at the front edges. This does not
indicate trouble. It is attributable to the hot gas line design.
This prevents moisture from accumulating and has nothing to
do with the storage temperature inside.
ATTENTION
If the unit is turned off or unplugged, YOU MUST ALLOW THREE (3) MINUTES
BEFORE RESTARTING OR REPLUGGING THE UNIT. The unit will not start if you
attempt to restart it in less than three (3) minutes.
1. Remove the hinge cap by twisting it off.
2. Remove the upper hexagonal head screws. The
freezer door can now be removed.
3. Remove the middle hexagonal head screws. The
refrigerator door can now be removed.
4. Remove the hinge-side leg, attach it to the leg hole
on the other side.
5. Remove the other leg, attach it to leg hole on the
other side.
6. Attach the bottom hinge symmetrically to the other
side of the cabinet.
7. Remove the upper hinge plug buttons and insert
them in the holes from which the screws were removed in Step 2.
8. Remove the middle hinge plastic cover and remount it to cover the holes from which the screws
were removed in Step 3.
9. Remove the door plug button from the top of each door using a screwdriver and insert in the hole
on the opposite side of each door.
10. Attach the refrigerator door to the bottom hinge.
11. Rotate the middle hinge 180 degrees. Attach it
to the refrigerator door and secure it with a
screw. (Do not tighten the screw completely.)
12. Attach the upper hinge to the freezer door.
Attach the freezer to the middle hinge and use
the screw to attach the upper hinge. (Do not
tighten the screw completely.)
13. The direction in which the doors open has now
been changed; however, the following points
should be checked:
Installing the Hinge Clip
A) Make sure both doors are on straight.
B) Make sure that there is no space between the door
gasket and the refrigerator unit itself when the doors
are closed.
C) Make sure that the gasket on the hinged side is not
caught between the door and the unit when the door
is opened or closed. (If the door is forced closed
when the gasket is caught, the gasket may be
damaged.)
14. After making sure that the doors are installed
correctly, tighten all the screws holding the
hinges. If they are not tightened, the doors may
slip out of position or there may be an opening
between the doors and the cabinet.
15. For models with senior living handles, remove the
screws holding the handle on the door. Remove
plastic pins from the other side of the door and
insert them into the holes where the screws were
removed. Re-install the handle using the same
screws that were removed from the door handles.
WARNING
Do not route high-voltage electrical cords
underneath the hinge clip. Only use the
clip to cover low-voltage cords.
Download PDF

advertising