Marvel | ML15CRP1XP | Owner's Manual | Marvel ML15CRP1XP Owner's Manual

Installation
Operation and
Maintenance
Instructions
Ice Machine
ML15CRS1XS
ML15CRS1XB
ML15CRP1XP
Installation Operation and Maintenance Instructions
Contents
Service
Intro
Troubleshooting
Warranty
Safety
Obtaining Service
Safety and Warning
Disposal and Recycling
Installation
Environmental Requirements
Electrical
Cutout Dimensions
Product Dimensions
Side by Side Installation Water
Hookup
Anti-Tip Bracket
General Installation
Overlay Door Panel Dimensions
Overlay Door Panel Installation
Grille Installation
Door Swing
Door Adjust
Operating Instructions
First Use
Ice
Airflow and Product Loading
Maintenance
Cleaning
Cleaning Condenser
Extended Non-Use
2
Installation Operation and Maintenance Instructions
Welcome to the Marvel Experience
Congratulations on adding a new Marvel crescent ice maker to your home and thank
you for choosing our quality American-built product. You’ll enjoy years of crescent ice
in the comfort and convenience of your home, backed by our full worry-free warranty.
We are thrilled to welcome you to our growing community of Marvel owners, who
trust in our products and our support.
The information in this guide is intended to help you install and maintain your new
Marvel crescent ice maker to protect and prolong the lifetime of your unit. We
encourage you to contact our Technical Support team at (800) 223-3900 with any
questions.
Cheers!
3
Installation Operation and Maintenance Instructions
Safety and Warning
Disposal and Recycling
! DANGER
NOTICE
Please read all instructions before installing, operating, or
RISK OF CHILD ENTRAPMENT. Before you throw away
servicing the appliance.
your old refrigerator or freezer, take off the doors and leave
shelves in place so children may not easily climb inside.
Use this appliance for its intended purpose only and follow
these general precautions with those listed throughout this
If the unit is being removed from service for disposal, check and
guide:
obey all federal, state and local regulations regarding the
disposal and recycling of refrigeration appliances, and follow
SAFETY ALERT DEFINITIONS
these steps completely:
Throughout this guide are safety items labeled with a Danger,
Warning or Caution based on the risk type:
1. Remove all consumable contents from the unit.
! DANGER
2. Unplug the electrical cord from its socket.
3. Remove the door(s)/drawer(s).
Danger means that failure to follow this safety statement
will result in severe personal injury or death.
Environmental Requirements
! WARNING
This unit is designed to operate between 50°F (10°C) and
100°F (38°C). Higher ambient temperatures may reduce the
Warning means that failure to follow this safety statement
unit’s ability to reach low temperatures and/or reduce ice
could result in serious personal injury or death.
production on applicable models.
For best performance, keep the unit out of direct sunlight and
! CAUTION
away from heat generating equipment.
Caution means that failure to follow this safety statement
In climates where high humidity and dew points are present,
may result in minor or moderate personal injury, property
condensation may appear on outside surfaces. This is
or equipment damage.
considered normal. The condensation will evaporate when the
humidity drops.
! WARNING
CALIFORNIA PROPOSITION 65
! CAUTION
This product contains chemicals known to the state of
California to cause cancer and birth defects or other
reproductive harm.
Damages caused by ambient temperatures of
www.P65warnings.CA.gov
warranty.
40°F (4°C) or below are not covered by the
4
Installation Operation and Maintenance Instructions
Cutout Dimensions
Electrical
PREPARE SITE
! WARNING
Your U-Line product has been designed for either free-standing
or built-in installation. When built-in, your unit does not require
SHOCK HAZARD — Electrical Grounding Required. Never
additional air space for top, sides, or rear. However, the front
attempt to repair or perform maintenance on the unit until
grille must NOT be obstructed, and clearance is required for an
the electricity has been disconnected.
electrical connection in the rear.
Never remove the round grounding prong from the plug
and never use a two-prong grounding adapter.
! CAUTION
Altering, cutting or removing power cord, removing power
plug, or direct wiring can cause serious injury, fire, loss of
property and/or life, and will void the warranty.
Unit can NOT be installed behind a closed cabinet door.
Never use an extension cord to connect power to the unit.
CUTOUT DIMENSIONS
Always keep your working area dry.
NOTICE
Electrical installation must observe all state and local
Preferred location
for water line and
eletrical outlet is in
adjacent cabinet.
codes. This unit requires connection to a grounded
(three-prong), polarized receptacle that has been placed
by a qualified electrician.
34-1/4"
(87 0 mm)
to
35"
(889 mm)
The unit requires a grounded and polarized 115 VAC, 60 Hz,
15A power supply (normal household current). An individual,
properly grounded branch circuit or circuit breaker is
recommended. A GFCI (ground fault circuit interrupter) is
7"
(178 mm)
4"
(102 mm)
15-1/4"
(38 7 mm)
usually not required for fixed location appliances and is not
recommended for your unit because it could be prone to
nuisance tripping. However, be sure to consult your local codes.
See CUTOUT DIMENSIONS for recommended receptacle
location.
5
24"
(610 mm)
5/8"
(16 mm)
Installation Operation and Maintenance Instructions
Product Dimensions - ML15CRS1XS & ML15CRS1XB
Not Including Handle
*Add 3/4" To Depth For Water Line Clearance
6
Installation Operation and Maintenance Instructions
Product Dimensions - ML15CRP1XP
Includes 3/4" (20 mm)
Overlay Panel
*Add 3/4" To Depth For Water Line Clearance
7
Installation Operation and Maintenance Instructions
Side-by-Side Installation
3. Place bracket over holes and attach to unit with two screws
removed in step 2 using a T-25 Torx driver. Tighten screws
Two units may be installed side-by-side.
fully.
Cutout width for a side-by-side installation is the cutout
4. Gently push units into position. Be careful not to entangle
dimension of a single unit times two.
the electrical cord or water line, if applicable.
No trim kit is required. However, 1/4" (6 mm) of space needs to
5. Re-check the leveling, from front to back and side to side.
be maintained between the units to ensure unobstructed door
Make any necessary adjustments. The unit’s top surface
swing.
should be approximately 1/8" (3 mm) below the countertop.
Units must operate from separate, properly grounded electrical
receptacles placed according to each unit’s electrical
specifications requirements.
Side-by-Side Installation with Bracket
1. Slide both units out so screws on top of units are easily
accessible.
2. Remove screws as shown below.
8
Installation Operation and Maintenance Instructions
Water Hookup
! CAUTION
PREPARE PLUMBING
Do not use any plastic water supply line. The line is under
The water valve uses a standard 1/4" (6.35 mm) compression
pressure at all times. Plastic may crack or rupture with age
fitting.
and cause damage to your home.
Do not use tape or joint compound when attaching a
braided flexible water supply line that includes a rubber
! CAUTION
gasket. The gasket provides an adequate seal – other
materials could cause blockage of the valve.
Plumbing installation must observe all state and local
codes. All water and drain connections MUST BE made by
Failure to follow recommendations and instructions may
a licensed/qualified plumbing contractor. Failure to follow
result in damage and/or harm, flooding or void the product
recommendations and instructions may result in damage
warranty.
and/or harm.
Use new hose set. Do not reuse old hose set.
Water Supply Connection
When connecting the water supply, please note the following:
! CAUTION
• Before installing the unit and connecting to the cold water
supply, review the local plumbing codes.
Turn off water supply and disconnect electrical supply to
unit prior to installation.
• The water pressure should be between 20 and 120 psi (138
and 827 kPa).
Use caution when handling back panel. The edges could
be sharp.
• The water line MUST have a shut-off valve in the supply line.
1. Turn off water supply and disconnect electrical supply to
product prior to attempting installation.
• The water line should be looped into 2 coils. This will allow
the unit to be removed for cleaning and servicing. Make
certain that the tubing is not pinched or damaged during
2. Remove the back panel.
installation.
! WARNING
Connect to potable water supply only.
9
Installation Operation and Maintenance Instructions
Anti-Tip Bracket
3. Locate water valve inlet.
1. Slide unit out so screws on top of unit are easily accessible.
2. Remove the two screws from the opposite side of the hinge
assembly using a T-25 Torx driver (see below).
4. Break away filler feature in bushing with flat screwdriver.
Remove
ZLWKɠDW
screwdriver
5. Thread water line through back panel hole (with bushing).
3. Place bracket over holes and attach to unit with two screws
removed in step 2 using a T-25 Torx driver. Tighten screws
fully.
4. Gently push unit into position. Be careful not to entangle the
electrical cord or water line, if applicable.
5. Check to be sure the unit is level from front to back and side
6. Locate water valve inlet and connect to valve.
to side. Make any necessary adjustments. The unit’s top
surface should be approximately 1/8" (3 mm) below the
7. Turn on water supply and check for leaks.
countertop.
8. Reinstall back panel.
9. Install retaining clip.
6. Secure bracket into adjoining surface.
10
Installation Operation and Maintenance Instructions
General Installation
INSTALLATION
1. Plug in the power/electrical cord.
LEVELING INFORMATION
1. Use a level to confirm
2. Gently push the unit into position. Be careful not to entangle
the unit is level. Level
the cord or water and drain lines.
should be placed
along top edge and
side edge as shown.
3. Re-check the leveling, from front to back and side to side.
Make any necessary adjustments. The unit’s top surface
should be approximately 1/8" (3 mm) below the countertop.
4. Install the anti-tip bracket.
1
5. Remove interior packing material and wipe out the inside of
the unit with a clean, water-dampened cloth.
2. If the unit is not level,
adjust the legs on the corners of the unit as necessary.
Turn to Adjust
3. Confirm the unit is level after each adjustment and repeat
the previous steps until the unit is level.
INSTALLATION TIP
If the room floor is higher than the floor in the cutout opening,
adjust the rear legs to achieve a total unit rear height of 1/8"
(3 mm) less than the opening’s rear height. Shorten the unit
height in the front by adjusting the front legs. This allows the
unit to be gently tipped into the opening. Readjust the front legs
to level the unit after it is correctly positioned in the opening.
11
Installation Operation and Maintenance Instructions
Overlay Door Panel Dimensions
- ML15CRP1XP
OVERLAY PANEL
Overlay Panel Dimensions
NOTICE
Due to differences in surrounding cabinetry the panel may
not perfectly align with door. The procedure below is
BACK SURFACE MUST HAVE AMPLE FLAT SURFACE
TO MOUNT OVERLAY PANEL FLAT AND WITHOUT
INTERFERENCE
3/4"
designed to provide a finished overlay panel that
seamlessly integrates with surrounding cabinetry.
(20 mm)
14-3/4"
(375 mm)
The door panel must not weigh more than 20 lbs (10 kg).
It is important to ensure that all drilled holes are drilled to
the correct depth in order to avoid splits in the wood when
hardware is installed.
When applying an overlay panel to a unit, ensure that
both sides are finished in order to prevent warping.
A full overlay door panel completely covers the door frame and
30-1/4"
(768 mm)
provides a built-in appearance.
Overlay Panel Preparation
1. Cut the panels to the dimensions listed in the diagram
below.
2. Optional: Stain or Finish panel to desired stain or color. Be
sure to closely follow the instructions provided by the
manufacturer.
Overlay Panel
3. Optional: Install handles and hardware.
12
Installation Operation and Maintenance Instructions
Overlay Door Panel Installation - ML15CRP1XP
1. Fully open door.
6.
Secure overlay panel to
door using clamps. A
robust tape may also be
2. Starting at corner, pull gasket
away from door.
Bar
Clamp
used. AGA Marvel
recommends the use of
bar clamps to secure the
3. Continue to pull gasket free
from gasket channel.
panel to the door. If using
tape, be certain the tape
will not damage panel
4. Upon removal, lay gasket down on a flat surface.
finish upon removal.
5. The panel should be aligned with the outside edge
(opposite the hinge) and high enough to align with the
highest point in the door.
7.
Door
Wood
Panel
Using a 7/64" (3 mm) drill
bit, drill 6 pilot holes into
the wood panel 1/2" (12
mm) deep using the holes
in the door frame as a
Align Top Of Panel With Highest Point Of Door
Bar
Clamp
guide.
Align Panel
Against
Door Edge First
It is important to ensure that all drilled holes are drilled to
the correct depth in order to avoid splits in the wood when
hardwood is installed.
8.
NOTICE
Locate 6 of the #6x 1-1/4" (32 mm) screws provided with
your unit.
Due to differences in floor construction or surrounding
cabinetry, the panel may not sit flush with the top of
9.
the door.
Using a Phillips screwdriver, place one screw into each of
the 6 pilot holes and screw down. Do not over tighten
Panel
screws.
Door
10. Be sure the screws force their way past the opening on
the gasket channel and sit flush against the bottom of the
channel.
Overlay Panel
13
Overlay Panel
Installation Operation and Maintenance Instructions
Door Swing
11. Remove clamps from door.
NOTICE
Wall
If panel requires additional adjustment after removing
1/4" Min.
(6 mm)
clamps, slightly loosen each screw and adjust panel as
Wall
2-1/8" Min.
(54 mm)
necessary. Tighten screws upon completion.
12. Starting at the corners, re-install the gasket into the gasket
channel in the frame. Make sure the gasket is fully seated.
This may take some force.
Grille Installation
90°
Door Swing
REMOVING AND INSTALLING GRILLE
90°
Door Swing
! WARNING
Units have a zero clearance for the door to open 90°, when
Disconnect electric power to the unit before
removing the grille.
installed adjacent to cabinets.
When using the unit, the grille must be installed.
Stainless Steel and black and white models require
Removing the grille
installed next to a wall.
2-1/8" (54 mm) door clearance to accommodate the handle if
1. Disconnect power to the unit.
Overlay models require 1/4" (6 mm) clearance if installed
next to a wall. Allow for additional space for any knobs or
2. Loosen the two screws (1).
pulls installed on the overlay panel/frame.
3. Remove grille (2) from unit.
Installing the grille
1. Align cabinet and grille holes and secure, but do not over
tighten grille screws (1).
2. Reconnect power to the unit.
14
Installation Operation and Maintenance Instructions
Door Adjust
Location of the unit may make it desirable to mount the door
on the opposite side of the cabinet.
HINGE COVER
Hinge cover included with the literature bag is optional.
The hinge hardware will be removed and reinstalled on the
opposite side of the cabinet.
To install hinge cover:
TO REVERSE THE DOOR (Black and Stainless Models)
1. Press hinge cover squarely over hinge.
Hinge Cover
DOOR ALIGNMENT AND ADJUSTMENT
Align and adjust the door if it is not level or is not sealing
properly. If the door is not sealed, the unit may not cool properly,
or excessive frost may form in the interior.
NOTICE
Properly aligned, the door’s gasket should be firmly in
Remove top hinge and door:
contact with the cabinet all the way around the door (no
gaps). Carefully examine the door’s gasket to ensure that it
is firmly in contact with the cabinet. Also make sure the
door gasket is not pinched on the hinge side of the door.
1. Remove hinge cover from top of unit.
To align and adjust the door:
2. Hold door to keep it from falling.
1. Gently pry off hinge cover from top of unit.
3. Remove top hinge from cabinet using a Torx T-25
screwdriver to remove three screws.
2. Loosen (do not remove) top and bottom hinge screws using
a Torx T-25 screwdriver on the top and a 1/4" socket on the
4. Remove pivot screw from hinge, flip hinge over, and
bottom.
install the pivot screw in the same hole from the
opposite surface.
3. Align door squarely with cabinet.
Top Hinge
Right Side
4. Make sure gasket is firmly in contact with cabinet all the way
around the door (no gaps).
Top Hinge
Left Side
5. Tighten bottom hinge screws.
6. Tighten top hinge screws and replace hinge cover.
15
Pivot
Screw
Installation Operation and Maintenance Instructions
Install top hinge and door:
1. Install the top hinge. Do not tighten.
5. Remove door by tilting forward and lifting door off bottom
hinge. Retain shoulder washers; they will be reused.
2. Rotate the door 180o to reverse and set the door onto
the bottom hinge.
6. Remove three screws from hinge holes on the opposite
side. Reinstall into holes where the hinge was removed.
Take care not to scratch the cabinet.
3. Align edge of the hinge with the outer edge of the unit.
4. Tighten three hinge screws and replace hinge cover.
Remove bottom hinge:
Align and adjust the door:
1. Remove bottom hinge from cabinet using a 1/4" socket
Align and adjust the door (see DOOR ADJUST)
2. Remove corresponding screws on opposite side of cabinet.
On some models there may be a nut behind one or both
screws on either side.
Install bottom hinge:
Install two or three screws, depending on model. Replace
nuts if used.
16
Installation Operation and Maintenance Instructions
TO REVERSE THE DOOR (Overlay Model)
Remove bottom hinge:
1. Remove bottom hinge from cabinet.
2. Remove corresponding screws on opposite side of cabinet.
On some models there may be a nut behind one or both
screws on either side.
Remove top hinge and door:
Install bottom hinge:
1. Hold door to keep it from falling.
Install two or three screws, depending on model. Replace
nuts if used.
2. Remove top hinge from cabinet using a Torx T-25
screwdriver to remove three screws. Set aside and save for
possible future use.
Install top hinge and door:
1. Use alternate hinge supplied with unit and reinstall the
screws. Do not tighten..
2. Lift the door on to the bottom hinge.
3. Align flat edge of the hinge with the outer edge of the unit.
4. Tighten three screws.
3. Remove door by tilting forward and lifting door off bottom
hinge. Retain shoulder washers; they will be reused.
4. Remove three screws from hinge holes on the opposite
side. Reinstall into holes where the hinge was removed.
Take care not to scratch cabinet.
Align and adjust the door:
Align and adjust the door (see DOOR ADJUST).
17
Installation Operation and Maintenance Instructions
First Use
To turn off ice production: Raise the bin arm into an
All controls are preset at the factory. Initial startup
for ice storage.
upright and locked position. The unit will preserve temperature
requires no adjustments.
NOTICE
NOTICE
If not intending to use the ice maker, turn the water supply
AGA Marvel recommends discarding the ice produced
valve off. It is also important to raise the bin arm of the ice
during the first two to three hours of operation to avoid
maker (see above). Failure to raise the bin arm may result
possible dirt or scale that may dislodge from the water
in damage to the water valve.
line.
Certain sounds are normal during the unit’s operation. You may
To turn the unit on or off:
hear the compressor or fan motor, the water valve, or ice
ON
OFF
dropping into the ice bucket.
! CAUTION
Press the rocker switch located inside the door on the front
panel, or behind the grille.
NEVER use an ice pick, knife or other sharp instrument to
separate cubes. Shake the ice bucket instead.
Ice
During periods of limited use or high ambient temperatures, it is
common for cubes to fuse together. Gently shake the bucket to
ICE MAKER OPERATION
break apart cubes. If not using the ice maker regularly, empty
the ice bucket periodically to ensure fresh cubes.
When the ice bucket is full, the ice making mechanism will
shut off. However, the refrigeration system will continue to
cool and maintain the ice supply.
It is normal for cubes to appear cloudy. The cause is air trapped
in the water because of fast freezing. It is not caused by the
health, taste or chemical make up of the water. It is the same air
that is in every glass of water you drink.
NOTICE
Do not place cans or bottles in the ice compartment
because they will freeze.
Remove the ice bucket for emptying and cleaning. To remove
the ice bucket, raise the bin arm and remove the bucket from
the ice compartment. Use the ice bucket for ice storage only.
OFF
ON
18
Installation Operation and Maintenance Instructions
ICE MAKER ADJUSTMENT
4. Install the ice maker assembly cover.
Ice Cube Thickness Adjustment
Interval - As Required
ADJUSTING ICE HARVEST
On ice maker equipped models, adjust the cube size by
1. Remove the front grille (see GRILLE INSTALLATION).
changing water amount injected into the ice maker assembly as
follows:
2. Using a flat tip screwdriver, turn the adjusting screw (3) a
small increment clockwise for a COLDER setting (slower ice
production) or counterclockwise for a WARMER setting
(faster ice production).
1
OL
C
1
2
DE R
3
Warmer Colder
3. Reinstall the front grille (two screws).
2
Airflow and Product Loading
1. Remove the ice maker assembly cover (1).
NOTICE
The unit requires proper airflow to perform at its highest
2. Find the adjusting screw on the ice maker assembly control
efficiency. Do not block the front grille at any time, or the
box (2). The adjusting screw is just below the minus (-) and
unit will not perform as expected. Do not install the unit
plus (+) signs on the control box.
behind a door.
! CAUTION
Too large of an adjustment to the screw can cause the
water to overflow the ice maker and can cause property
damage.
3. Turn the adjusting screw toward the minus (-) sign
(clockwise) for smaller cubes or toward the plus (+) sign
(counterclockwise) for larger cubes.
19
Installation Operation and Maintenance Instructions
Cleaning
Using abrasive pads such as ScotchBrite™ will cause the
graining in the stainless steel to become blurred.
EXTERIOR CLEANING
Vinyl Clad (Black or White) Models
Rust not cleaned up promptly can penetrate the surface of
Clean surfaces with a mild detergent and warm water solution.
the stainless steel and complete removal of the rust may
Do not use solvent-based or abrasive cleaners. Use a soft
not be possible.
sponge and rinse with clean water. Wipe with a soft, clean towel
to prevent water spotting.
Integrated Models
To clean integrated panels, use household cleaner per the
Clean any glass surfaces with a non-chlorine glass cleaner.
cabinet manufacturer’s recommendations.
Stainless Models
INTERIOR CLEANING
Stainless door panels, handles and frames can discolor when
Disconnect power to the unit.
exposed to chlorine gas, pool chemicals, saltwater or cleaners
with bleach.
Clean the interior and all removed components using a mild
nonabrasive detergent and warm water solution applied with a
Keep your stainless unit looking new by cleaning with a good
soft sponge or non-abrasive cloth.
quality all-in-one stainless steel cleaner and polish monthly. For
best results use Claire® Stainless Steel Polish and Cleaner.
Rinse the interior using a soft sponge and clean water.
Comparable products are acceptable. Frequent cleaning will
remove surface contamination that could lead to rust. Some
installations may require cleaning weekly.
Do not use any solvent-based or abrasive cleaners. These
types of cleaners may transfer taste to the interior products and
damage or discolor the interior.
Do not clean with steel wool pads.
Do not use stainless steel cleaners or polishes on any
glass surfaces.
Clean any glass surfaces with a non-chlorine glass cleaner.
Do not use cleaners not specifically intended for stainless
steel on stainless surfaces (this includes glass, tile and
counter cleaners).
If any surface discoloring or rusting appears, clean it quickly with
Bon-Ami® or Barkeepers Friend Cleanser® and a nonabrasive
cloth. Always clean with the grain. Always finish with Claire®
Stainless Steel Polish and Cleaner or comparable product to
prevent further problems.
20
Installation Operation and Maintenance Instructions
DEFROSTING
Cleaning Condenser
Manual Defrost Models
INTERVAL - EVERY SIX MONTHS
Unit is a manual defrost model and will require occasional
defrosting. When there is build-up of 1/4" (6 mm) or more of
To maintain operational efficiency, keep the front grille free of
frost, manually defrost the unit.
dust and lint, and clean the condenser when necessary.
Depending on environmental conditions, more or less
! CAUTION
frequent cleaning may be necessary.
DO NOT use an ice pick or other sharp instrument to help
! WARNING
speed up defrosting. These instruments can puncture the
inner lining or damage the cooling unit. DO NOT use any
type of heater to defrost. Using a heater to speed up
Disconnect electric power to the unit before
defrosting can cause personal injury and damage to the
cleaning the condenser.
inner lining.
NOTICE
To defrost:
DO NOT use any type of cleaner on the
1. Disconnect power to the unit.
condenser unit.
2. Remove ice bucket and discard ice.
1. Remove the grille. (See GRILLE INSTALLATION).
3. Place towel or other absorbent material on bottom of ice bin.
2. Clean the condenser coil using a using a soft brush
with a “combing” action or vacuum cleaner. Do not
touch the condenser coil.
4. Fill the ice bucket half full with warm, not hot water. This will
help the unit defrost faster.
3. Install the grille.
5. Place the ice bucket back into the unit on top of a towel or
other absorbent material.
Condenser
6. Prop the door in an open position (2 in. [50 mm] minimum).
7. After about 1 hour remove the ice bin and discard water.
8. Allow the frost to melt naturally.
9. After the frost melts completely clean the interior and all
removed components. (See INTERIOR CLEANING).
NOTICE
DO NOT clean ice bucket using a dishwasher. The bucket is
not dishwasher safe and will be damaged.
10. When the interior is dry, reconnect power and turn unit on.
NOTE: To safeguard against contamiments in ice,
discard first three batches of ice after defrosting.
21
Installation Operation and Maintenance Instructions
Extended Non-Use
VACATION/HOLIDAY, PROLONGED SHUTDOWN
For questions regarding extended non-use, please
The following steps are recommended for periods of
call AGA Marvel at 800.223.3900.
extended non-use or if the unit will be exposed to
temperatures of 40°F (5°C) or less:
! CAUTION
1. Remove all consumable content from the unit.
Damage caused by freezing temperatures is not covered
by the warranty.
2. Disconnect the power cord from its outlet/socket and
leave it disconnected until the unit is returned to service.
Do not put anti-freeze in your unit.
3. Turn off the water supply.
4. If ice is on the evaporator, allow ice to thaw naturally.
5. Clean and dry the interior of the cabinet. Ensure all water
has been removed from the unit.
6. Disconnect the water and drain line making sure all water
is removed from the lines.
7. The door must remain open to prevent formation of mold
and mildew. Open door a minimum of 2"
(50 mm) to provide the necessary ventilation.
22
Installation Operation and Maintenance Instructions
Troubleshooting
BEFORE CALLING FOR SERVICE
TROUBLESHOOTING GUIDE
If you think your AGA Marvel product is malfunctioning, read
! DANGER
the CONTROL OPERATION section to clearly understand the
function of the control.
ELECTROCUTION HAZARD. Never attempt to repair or
perform maintenance on the unit before disconnecting
If the problem persists, read the NORMAL OPERATING
the main electrical power.
SOUNDS and TROUBLESHOOTING GUIDE sections below
to help you quickly identify common problems and possible
causes and remedies. Most often, this will resolve the problem
Troubleshooting - What to check when problems occur:
without the need to call for service.
IF SERVICE IS REQUIRED
If you do not understand a troubleshooting remedy, or your
product needs service, contact AGA Marvel directly
Problem
Possible Cause and Remedy
Unit Develops
Frost on
Internal
Surfaces.
If there is excessive build-up of 1/4" or more,
manually defrost the unit.
Ensure the door is closing and sealing properly.
High ambient temperature and excessive
humidity can also produce frost.
Unit Develops
Condensation
on External
Surfaces.
The unit is exposed to excessive humidity.
Moisture will dissipate as humidity levels
decrease.
Product Is
Freezing.
Because product in contact with the rear wall
may freeze, ensure no product is touching the
rear wall.
Adjust the temperature to a warmer set point.
Product is Not
Cold Enough.
Adjust the temperature to a cooler set point.
Ensure unit is not located in excessive ambient
temperatures or in direct sunlight.
Ensure the door is closing and sealing properly.
Ensure nothing is blocking the front grille, found
at the bottom of the unit.
Ensure the condenser coil is clean and free of
any dirt or lint build-up.
at 800.223.3900
When you call, you will need your product Model and Serial
Numbers. This information appears on the Model and Serial
number plate located on the upper right or rear wall of the
interior of your product.
NORMAL OPERATING SOUNDS
All models incorporate rigid foam insulated cabinets to
provide high thermal efficiency and maximum sound reduction
for its internal working components. Despite this technology,
your model may make sounds that are unfamiliar.
Normal operating sounds may be more noticeable because of
the unit’s environment. Hard surfaces such as cabinets, wood,
vinyl or tiled floors and paneled walls have a tendency to
reflect normal appliance operating noises.
Causes which affect the internal temperatures of the
cabinet include:
Listed below are common refrigeration components with a
• Temperature setting.
brief description of the normal operating sounds they make.
• Ambient temperature where installed.
NOTE: Your product may not contain all the components
listed.
• Installation in direct sunlight or near a heat source.
• Compressor: The compressor makes a hum or pulsing
sound that may be heard when it operates.
• The number of door openings and the time the door is open.
• Obstruction of front grille or condenser.
• Evaporator: Refrigerant flowing through an evaporator
may sound like boiling liquid.
• Condenser Fan: Air moving through a condenser may be
heard.
23
Household Product Warranty
Entire Product
Limited One Year Parts and Labor Warranty
AGA MARVEL warrants that it will supply all necessary parts
and labor to repair or replace in the end user’s home or office,
any component which proves to be defective in material or
workmanship, subject to the condition and exclusions stated
below, for a period of one year from the date of purchase by the
end user.
Parts or Service
Not Supplied or Designated by AGA MARVEL The
above warranties also do not apply if:
Additional Second Through Fifth Year
Limited Parts Only Warranty
During the four years following expiration of the one year limited
warranty, AGA MARVEL will supply replacement parts for the
hermetically sealed refrigeration system which consists of the
compressor, condenser, drier, accumulator, bypass valve,
connecting tubing and the evaporator that are proven to be
defective due to workmanship or materials subject to the
conditions and exclusions below.
• The refrigeration equipment is not in the possession of the
original end use purchaser.
The above warranties do not cover:
• Shipping costs of replacement parts or returned defective
parts.
• Customer education or instructions on how to use the
appliance.
• Any content loss due to product failure.
• Removal or installation of product.
Nor do the above warranties cover failure of this product or its
components due to:
• The original bill of sale, deliver date, or serial number
cannot be verified.
• Defective parts are not returned for inspection if so
requested by AGA MARVEL.
The warranties set forth herein are the only warranties extended
by AGA MARVEL. Any implied warranties, including the implied
warranty of merchantability, are limited to the duration of these
express warranties. In no event shall AGA MARVEL be liable for
any consequential or incidental damages or expenses resulting
from breach of these or any other warranties, whether express or
implied.
Some states do not allow the exclusion or limitation of
consequential damages or a limitation on how long an implied
warranty lasts, so the above exclusion or limitation may not apply
to you. This warranty gives you specific legal rights and you may
have other rights that may vary from state to state.
No person, firm, or corporation is authorized to make any other
warranty or assume any other obligation for AGA MARVEL.
These warranties apply only to products used in any of the fifty
states of the United States and the District of Columbia.
To obtain performance of this warranty, report any defects to:
• Transportation or subsequent damages.
• Improper installation, misuse, abuse, accident or
alteration, use of wiring not conforming to electrical
codes, low or high voltages, failure to provide
necessary maintenance, or other unreasonable use.
• Improper installation, misuse, abuse, accident or
alteration, use of wiring not conforming to electrical
codes, low or high voltages, failure to provide
necessary maintenance, or other unreasonable use.
1260 E. VanDeinse
St. Greenville MI
48838
Phone: 800.223.3900
24
Obtaining Service
If Service is Required:
• If the product is within the first year warranty period please
contact your dealer or call AGA MARVEL Customer Service
at 800.223.3900 for directions on how to obtain warranty
coverage in your area.
• If the product is outside the first year warranty period, AGA
MARVEL Customer Service can provide recommendations of
service centers in your area. A listing of authorized service
centers is also available at www.agamarvel.com under the
service and support section.
• In all correspondence regarding service, be sure to give the
service number, serial number, located on your product’s
serial plate, and proof of purchase.
• Try to have information or description of nature of the
problem, how long the unit has been running, the room
temperature, and any additional information that may be
helpful in quickly solving the problem.
• Table B is provided for recording pertinent information
regarding your product for future reference.
For Your Records
Date of Purchase
Dealer’s name
Dealer’s Address
Dealer’s City
Dealer’s State
Dealer’s Zip Code
Appliance Serial Number
Appliance Service Number
Date Warranty Card Sent
(Must be within 10 days of
purchase).
25
www.agamarvel.com
10/11/18
30603 Rev_A
Download PDF

advertising