U-Line | UADA24RGLINT00A | Manual and User Guide | U-Line UADA24RGLINT00A Manual and User Guide

U-Line UADA24RGLINT00A Manual and User Guide
USER GUIDE & SERVICE MANUAL
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
RIGHT PRODUCT. RIGHT PLACE. RIGHT TEMPERATURE. SINCE 1962.
ADA Series
•
ADA24RGL
•
24" Glass Door Refrigerator
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Contents
Intro
Safety
Extended Non-Use
Service
Safety and Warning
Troubleshooting
Disposal and Recycling
Warranty
Installation
Service Extended
Environmental Requirements
Wire Diagram
Electrical
Product Liability
Cutout Dimensions
Warranty Claims
Product Dimensions
Parts
Side by Side Installation
Ordering Replacement Parts
Anti-Tip Bracket
System Diagnosis Guide
General Installation
Compressor Specifications
Integrated Panel Dimensions
Troubleshooting Extended
Integrated Panel Installation
Control Quick Guide
Grille / Plinth Installation
Thermistor
Door Swing
Defrost
Door Stop
Remove Fan and Cover
Door Adjust
Operating Instructions
First Use
Control Operation
Sabbath Mode
Airflow and Product Loading
Interior Shelves
Maintenance
Cleaning
Cleaning Condenser
USER GUIDE
u-line.com
WELCOME TO U-LINE
Congratulations on your U-Line purchase. Your product comes from a company with over five decades and three generations
of premium modular ice making, refrigeration, and wine preservation experience. U-Line continues to be the American
leader, delivering versatility and flexibility for multiple applications including residential, light commercial, outdoor and marine
use. U-Line’s complete product collection includes modular Wine Captain® Models, Beverage Centers, Clear Ice Machines,
Crescent Ice Makers, Glass & Solid Door Refrigerators, Drawer Models, Freezers, and Combo® Models.
U-Line has captivated those with an appreciation for the finer things with exceptional functionality, style, inspired innovations
and attention to even the smallest details. We are known and respected for our unwavering dedication to product design,
quality and selection. U-Line is headquartered in Milwaukee, Wisconsin and has shipped product to five continents for over
two decades and is proud to have the opportunity to ship to you.
PRODUCT INFORMATION
Looking for additional information on your product? User Guides, Quick Reference Guides, CAD Drawings, Compliance
Documentation, and Product Warranty information are all available for reference and download at u-line.com.
PROPERTY DAMAGE / INJURY CONCERNS
In the unlikely event property damage or personal injury is suspected related to a U-Line product, please take the following
steps:
1. U-Line Customer Care must be contacted immediately at +1.800.779.2547.
2. Service or repairs performed on the unit without prior written approval from U-Line is not permitted. If the unit has been
altered or repaired in the field without prior written approval from U-Line, claims will not be eligible.
SERVICE INFORMATION
Answers to Customer Frequently Asked Questions are available at u-line.com under Customer Care or you may contact our
Customer Care group directly, contact information below.
GENERAL INQUIRIES
SERVICE & PARTS ASSISTANCE
U-Line Corporation
Monday - Friday 8:00 am to 4:30 pm CST
8900 N. 55th Street
T: +1.800.779.2547
Milwaukee, Wisconsin 53223 USA
F: +1.414.354.5696
Monday - Friday 8:00 am to 4:30 pm CST
Service Email: onlineservice@u-line.com
T: +1.414.354.0300
Parts Email: onlineparts@u-line.com
F: +1.414.354.7905
Email: sales@u-line.com
u-line.com
CONNECT WITH US
Designed, engineered and assembled in WI, USA
Introduction 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Safety and Warning
! DANGER
NOTICE
This unit contains R600a (Isobutane) which is a
Please read all instructions before installing,
flammable hydrocarbon. It is safe for regular
operating, or servicing the appliance.
use. Do not use sharp objects to expedite
defrosting. Do not service without consulting the
Use this appliance for its intended purpose only and follow
these general precautions with those listed throughout this
guide:
SAFETY ALERT DEFINITIONS
Throughout this guide are safety items labeled with a
Danger, Warning or Caution based on the risk type:
“R600a specifications” section included in the
User Guide. Do not damage the refrigerant
circuit.
! WARNING
Service must be done by factory authorized
service personnel. Any parts shall be replaced
! DANGER
with like components. Failure to comply could
increase the risk of possible ignition due to
incorrect parts or improper service.
Danger means that failure to follow this safety
statement will result in severe personal injury or
death.
! WARNING
Warning means that failure to follow this safety
statement could result in serious personal injury
or death.
! CAUTION
Caution means that failure to follow this safety
statement may result in minor or moderate
personal injury, property or equipment damage.
Safety and Warning 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Disposal and Recycling
! DANGER
RISK OF CHILD ENTRAPMENT. Before you throw
away your old refrigerator or freezer, take off
the doors and leave shelves in place so children
may not easily climb inside.
If the unit is being removed from service for disposal,
check and obey all federal, state and local regulations
regarding the disposal and recycling of refrigeration
appliances, and follow these steps completely:
1. Remove all consumable contents from the unit.
2. Unplug the electrical cord from its socket.
3. Remove the door(s)/drawer(s).
Disposal and Recycling 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Environmental Requirements
This model is intended for indoor/interior applications only
and is not to be used in installations that are open/
exposed to natural elements.
This unit is designed to operate between 50°F (10°C) and
100°F (38°C). Higher ambient temperatures may reduce
the unit’s ability to reach low temperatures and/or reduce
ice production on applicable models.
For best performance, keep the unit out of direct sunlight
and away from heat generating equipment.
In climates where high humidity and dew points are
present, condensation may appear on outside surfaces.
This is considered normal. The condensation will
evaporate when the humidity drops.
! CAUTION
Damages caused by ambient temperatures of
40°F (4°C) or below are not covered by the
warranty.
Environmental Requirements 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Electrical
! WARNING
SHOCK HAZARD — Electrical Grounding
Required. Never attempt to repair or perform
maintenance on the unit until the electricity has
been disconnected.
Never remove the round grounding prong from
the plug and never use a two-prong grounding
adapter.
Altering, cutting or removing power cord,
removing power plug, or direct wiring can cause
serious injury, fire, loss of property and/or life,
and will void the warranty.
Never use an extension cord to connect power to
the unit.
Always keep your working area dry.
NOTICE
Electrical installation must observe all state and
local codes. This unit requires connection to a
grounded (three-prong), polarized receptacle
that has been placed by a qualified electrician.
The unit requires a grounded and polarized 115 VAC,
60 Hz, 15A power supply (normal household current). An
individual, properly grounded branch circuit or circuit
breaker is recommended. A GFCI (ground fault circuit
interrupter) is usually not required for fixed location
appliances and is not recommended for your unit because
it could be prone to nuisance tripping. However, be sure
to consult your local codes.
See CUTOUT DIMENSIONS for recommended receptacle
location.
Electrical 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Cutout Dimensions
PREPARE SITE
Your U-Line product has been designed for either freestanding or built-in installation. When built-in, your unit
does not require additional air space for top, sides, or
rear. However, the front grille must NOT be obstructed,
and clearance is required for an electrical connection in
the rear.
! CAUTION
Unit can NOT be installed behind a closed cabinet
door.
CUTOUT DIMENSIONS
Preferred location
for electrical
outlet is in
5/8"
adjacent
(16 mm)
cabinet.
32"
(813 mm)
to
33"
(838 mm)
24"
(610 mm)
7"
(178 mm)
4"
(102 mm)
24-1/4"
(616 mm)
Cutout Dimensions 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Product Dimensions
Not Including Handle
23-1/4" (591 mm)
32" to 33”
(813 mm 838 mm)
24" (610 mm)
Product Dimensions 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Side-by-Side Installation
Two units may be installed side-by-side.
Cutout width for a side-by-side installation is the cutout
dimension of a single unit times two.
No trim kit is required. However, 1/4" (6 mm) of space
3. Place bracket over holes and attach to unit with two
screws removed in step 2 using a T-25 Torx driver.
Tighten screws fully.
4. Gently push units into position. Be careful not to
entangle the electrical cord or water line, if applicable.
5. Re-check the leveling, from front to back and side to
needs to be maintained between the units to ensure
side. Make any necessary adjustments. The unit’s top
unobstructed door swing.
surface should be approximately 1/8" (3 mm) below
the countertop.
Units must operate from separate, properly grounded
electrical receptacles placed according to each unit’s
electrical specifications requirements.
Side-by-Side Installation with Bracket
1. Slide both units out so screws on top of units are easily
accessible.
2. Remove screws as shown below.
Side-by-Side Installation 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Anti-Tip Bracket
1. Slide unit out so screws on top of unit are easily
accessible.
2. Remove the two screws from the opposite side of the
hinge assembly using a T-25 Torx driver (see below).
NOTE: 1224 models shown with four screw. 1215 models
only have three screws, but same screws are used in both
applications.
3. Place bracket (part #14154) over holes and attach to
unit with two screws removed in step 2 using a T-25
Torx driver. Tighten screws fully.
4. Gently push unit into position. Be careful not to
entangle the electrical cord or water line, if applicable.
5. Check to be sure the unit is level from front to back
and side to side. Make any necessary adjustments.
The unit’s top surface should be approximately 1/8"
(3 mm) below the countertop.
6. Secure bracket into adjoining surface.
Anti-Tip Bracket 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
General Installation
INSTALLATION
1. Plug in the power/electrical cord.
LEVELING INFORMATION
1. Use a level to
2. Gently push the unit into position. Be careful not to
confirm the unit is
entangle the cord.
level. Level should
be placed along top
3. Re-check the leveling, from front to back and side to
edge and side edge
side. Make any necessary adjustments. The unit’s top
as shown.
surface should be approximately 1/8" (3 mm) below
the countertop.
1
4. Remove the interior packing material and wipe out the
inside of the unit with a clean, water-dampened cloth.
2. If the unit is not level, adjust the legs on the corners of
the unit as necessary.
Turn to Adjust
3. Confirm the unit is level after each adjustment and
repeat the previous steps until the unit is level.
INSTALLATION TIP
If the room floor is higher than the floor in the cutout
opening, adjust the rear legs to achieve a total unit rear
height of 1/8" (3 mm) less than the opening’s rear height.
Shorten the unit height in the front by adjusting the front
legs. This allows the unit to be gently tipped into the
opening. Readjust the front legs to level the unit after it is
correctly positioned in the opening.
General Installation 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Integrated Frame
NOTICE
Due to differences in surrounding cabinetry the
panel may not perfectly align with door. The
2. Optional: Stain or Finish panel to desired stain or color.
Be sure to closely follow the instructions provided by
the manufacturer.
3. Optional: Install handles and hardware.
procedure below is designed to provide a
finished integrated panel that seamlessly
Integrated Frame Dimensions
integrates with surrounding cabinetry.
The door panel must not weigh more than 20 lbs
BACK SURFACE MUST HAVE AMPLE FLAT SURFACE
TO MOUNT OVERLAY FRAME FLAT AND WITHOUT
INTERFERENCE
3/4"
(20 mm)
(10 kg).
23-3/4"
(603 mm)
It is important to ensure that all drilled holes are
drilled to the correct depth in order to avoid
splits in the wood when hardware is installed.
When applying an integrated panel to a unit,
ensure that both sides are finished in order to
prevent warping. In some frame installations,
the panel may be visible through the glass while
the door is open.
2-3/4"
(70 mm)
30-1/4"
(768 mm)
A full integrated door panel completely covers the door
frame and provides a built-in appearance.
Integrated Frame Preparation
1. Cut the panels to the dimensions listed in the diagram
below.
Integrated Frame
Integrated Panel Dimensions 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Integrated Panel Installation
1. Fully open door/drawer.
6. Secure integrated
panel to door/drawer
Bar
Clamp
using clamps. A
robust tape may also
be used. U-Line
2. Starting at corner, pull
recommends the use
gasket away from door/
of bar clamps to
drawer.
Door/Drawer
secure the panel to
the door/drawer. If
3. Continue to pull gasket
using tape, be
free from gasket channel.
Wood
Panel
certain the tape will
not damage panel
4. Upon removal, lay gasket down on a flat surface.
5. The panel should be aligned with the outside edge
finish upon removal.
7. Using a 7/64" (3 mm)
(opposite the hinge) and high enough to align with the
drill bit, drill 6 pilot
highest point in the door/drawer.
holes into the wood
Bar
Clamp
panel 1/2" (12 mm)
Align Top Of Panel With Highest Point Of Door/Drawer
Align Panel
Against
Door/Drawer
Edge First
deep using the holes in the door/drawer frame as a
guide.
NOTICE
It is important to ensure that all drilled holes are
drilled to the correct depth in order to avoid
splits in the wood when hardwood is installed.
8. Locate 6 of the #6x 1-1/4" (32 mm) screws provided
with your unit.
NOTICE
Due to differences in floor construction or
surrounding cabinetry, the panel may not sit
flush with the top of the door/drawer.
Panel
Door
9. Using a Phillips screwdriver, place one screw into each
of the 6 pilot holes and screw down. Do not overtighten
screws.
10.Be sure the screws force their way past the opening on
the gasket channel and sit flush against the bottom of
the channel.
Integrated Panel
Integrated Panel
Integrated Panel Installation 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
11.Remove clamps from door/drawer.
NOTICE
If panel requires additional adjustment after
removing clamps, slightly loosen each screw and
adjust panel as necessary. Tighten screws upon
completion.
12.Starting at the corners, re-install the gasket into the
gasket channel in the frame. Make sure the gasket is
fully seated. This may take some force.
Integrated Panel Installation 2
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Grille - Plinth Installation
REMOVING AND INSTALLING GRILLE
! WARNING
Disconnect electric power to the unit before
removing the grille.
When using the unit, the grille (plinth strip/base
fascia) must be installed.
! WARNING
DO NOT touch the condenser fins. The condenser
fins are SHARP and can be easily damaged.
Removing the grille
1. Disconnect power to the unit.
2. Loosen the two screws (1). Some models may have
only one screw in the center.
3. Remove grille (2) and grille cap from unit.
Installing the grille
1. Align cabinet and grille holes and secure, but do not
overtighten grille screws (1).
2. Reconnect power to the unit.
1
2
Grille - Plinth Installation 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Door Swing
Wall
Wall
1/4" Min.
(6 mm)
90
Door Swing
2-1/8" Min.
(54 mm)
90
Door Swing
Units have a zero clearance for the door to open 90°,
when installed adjacent to cabinets.
Stainless Steel and black and white models require 2-1/8"
(54 mm) door clearance to accommodate the handle if
installed next to a wall.
Integrated models require 1/4" (6 mm) clearance if
installed next to a wall. Allow for additional space for any
knobs or pulls installed on the integrated panel/frame.
Door Swing 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Door Stop
3. On 24" models, a second pin is included for the bottom
hinge. Repeat steps above for second hinge.
Your U-Line unit was shipped to you with the optional
90° pin(s). (Models that are 15" wide include 1 pin. Models
that are 24" wide include 2 pins.) The unit’s door will open
NOTE: Threaded pin will be inserted from the bottom.
freely without a fixed opening angle limitation. If you
would like the door stop at 90° follow these instructions.
NOTICE
The pin is designed to stop the door at 90° under
normal operating conditions. It is not designed
for excessive force. Do not use the door to move
the unit in/out of the cutout during installation.
If your unit is already undercounter, it might
need to be moved out/forward to access the
hinge.
1. Locate the threaded pin.
2. With the door between 0° (closed) and 90° and using a
4. Carefully slide your unit back in place.
NOTICE
3/32" hex driver, install the threaded pin through the
The pin can be removed to return the door swing
hinge.
back to its original state by unscrewing the
threaded pin.
Door Stop 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Door Adjustments
DOOR ALIGNMENT AND ADJUSTMENT
Align and adjust the door if it is not level or is not sealing
properly. If the door is not sealed, the unit may not cool
properly, or excessive frost may form in the interior.
NOTICE
Properly aligned, the door’s gasket should be
firmly in contact with the cabinet all the way
around the door (no gaps). Carefully examine
the door’s gasket to ensure that it is firmly in
contact with the cabinet. Also make sure the
door gasket is not pinched on the hinge side of
the door.
TO REVERSE THE DOOR
Remove grille:
TO ALIGN AND ADJUST THE DOOR
Remove the grille (see GRILLE-PLINTH INSTALLATION
Remove grille:
section of this guide).
Remove the grille (see GRILLE-PLINTH INSTALLATION
section of this guide).
Remove top hinge and door:
1. Hold door to keep it from falling.
1. Loosen (do not remove) top and bottom hinge screws.
2. Remove top hinge from cabinet by removing three
2. Align door squarely with cabinet.
screws. Set aside and save for possible future use.
3. Make sure gasket is firmly in contact with cabinet all
the way around the door (no gaps).
4. Tighten bottom hinge screws.
5. Tighten top hinge screws.
REVERSING THE DOOR
Location of the unit may make it desirable to mount the
door on the opposite side of the cabinet.
The hinge hardware will be removed and installed on the
opposite side of the cabinet.
Door Adjustments 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
3. Remove door by tilting forward and lifting door off
3. Rotate gasket 180°, aligning notch with magnet
bottom hinge. Retain shoulder washers; they will be
assembly and pressing firmly into the gasket channel
reused.
starting at the corners.
4. Remove four screws from hinge holes on the opposite
4. Rotate door 180° to reverse.
side. Reinstall into holes where the hinge was
removed. Take care not to scratch cabinet.
Install top hinge and door:
1. Use alternate hinge supplied with unit and reinstall the
Remove and reinstall bottom hinge:
screws. Do not tighten..
1. Remove bottom hinge from cabinet by removing three
screws.
2. Lift the door on to the bottom hinge.
3. Align flat edge of the hinge with the outer edge of the
unit.
4. Tighten three screws.
2. Remove corresponding screws on opposite side of
cabinet.
Align and adjust the door:
Align and adjust the door (see DOOR ALIGNMENT AND
3. Flip hinge plate over and reinstall on opposite side.
ADJUSTMENT).
Install grille:
Prepare door for reinstallation:
Install the grille.
1. Remove gasket. This will reveal mounting holes for the
magnet assembly
2. Remove plunger bracket from door with T-10 TORX
driver. Be sure to only remove the two screws holding
the assembly to the door. Reinstall on the opposite end
of the door
Door Adjustments 2
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
First Use
All U-Line controls are preset at the factory. Initial startup
requires no adjustments.
NOTICE
U-Line recommends allowing the unit to run
overnight before loading with product.
When plugged in, the unit will begin operating under the
factory default settings. If the unit was turned off during
installation, simply press
and the unit will immediately
switch on. To turn the unit off, press
.
First Use 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Control Operation
Up Down
Not
Light Power Used LED
CONTROL FUNCTION GUIDE
FUNCTION
COMMAND
DISPLAY/OPTIONS
ON/OFF
Press
and release
Unit will immediately turn ON or OFF.
Press
and release to leave interior
Toggle lights
Adjust refrigerator set
light on for 3 hours
Press
or
and release
View temperature in unit
Press
and
together and release
Toggle between F/C
Hold
point
and
for 5 seconds
Glass door wine and beverage centers only.
When the “F” or “C” in the display is flashing, press
or
to adjust the set point temperature.
The display will flash and then toggle from set point
to temperature in unit.
The display will change units.
DOOR ALERT NOTIFICATION
When the door is left open for more than 5 minutes:
• An audible tone will sound for several seconds every
minute.
• “dr” will appear in display.
Close door to silence alert and reset.
Control Operation 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
L
Sabbath Mode
1
2
3
4
5
6
7
This unit is Star-K certified and offers a Sabbath mode.
Sabbath mode disables system responses to user initiated
activities and all external functions, including lighting,
display and audible alarms. The unit will still maintain
internal temperatures and set points. View a full list of
Star-K certified U-Line units at www.star-k.org.
To enable Sabbath Mode:
1. Press
(4) and hold for ten seconds and release (the
°F/°C symbol will flash briefly at the end of the ten
second period).
2. The interior light and control display (3) will go dark
until user resets mode.
3. NOTE: Although the display will not be visible, the
temperature controls in the unit remain active and
preserve the interior temperature.
Sabbath Mode remains active until
(4) is quickly
pressed and released.
Sabbath Mode 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Airflow and Product Loading
NOTICE
The unit requires proper airflow to perform at its
highest efficiency. Do not block the front grille,
internal fans or vents at any time, or the unit will
not perform as expected. When loading your
unit, leave space between the internal fans or
vents and product loaded. Anything blocking the
required airflow/circulation will result in uneven
temperature distribution in the cabinet and can
also freeze product. Do not install the unit
behind a door.
When properly loaded, your U-Line unit will store up to
140 (12 oz. [330 ml]) cans or 70 (12 oz. [330 ml]) bottles.
For optimal airflow, leave approximately two inches of
space around the fan and one inch around the back wall
and lower vents.
Airflow and Product Loading 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Interior Shelves
WIRE SHELF REMOVAL AND INSTALLATION
Insert the shelves as follows:
1. To move to a different position in the unit, insert shelf
at an angle, approximately 15-20°, over the rib in the
For ADA models equipped with wire racks, reposition the
side of the unit where you want to place the shelf. The
shelves as follows:
shelf must be started into the unit at an angle to clear
the door.
2. Continue to slide the shelf into the unit at an angle
until it clears the door.
3. Lower the shelf and push it in completely.
4. Install shelf retention clip.
1. Remove shelf retention clip.
2. Pull shelf out about 6" (1), until back of shelf clears the
“hump” on the right-hand side.
3. Tilt up right-hand edge of shelf (2).
4. Remove shelf from unit by pulling out (3).
Interior Shelves 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Cleaning
If any surface discoloring or rusting appears, clean it
EXTERIOR CLEANING
and a nonabrasive cloth. Always clean with the grain.
Vinyl Clad (Black or White)
Always finish with Claire® Stainless Steel Polish and
Clean surfaces with a mild detergent and warm water
solution. Do not use solvent-based or abrasive cleaners.
quickly with Bon-Ami® or Barkeepers Friend Cleanser®
Cleaner or comparable product to prevent further
problems.
Use a soft sponge and rinse with clean water. Wipe with a
soft, clean towel to prevent water spotting.
Clean any glass surfaces with a non-chlorine glass
Using abrasive pads such as Scotchbrite™ will
cause the graining in the stainless steel to
become blurred.
cleaner.
Stainless Models
Rust not cleaned up promptly can penetrate the
surface of the stainless steel and complete
removal of the rust may not be possible.
Stainless door panels, handles and frames can discolor
when exposed to chlorine gas, pool chemicals, saltwater
or cleaners with bleach.
Integrated Models
To clean integrated panels, use household cleaner per the
cabinet manufacturer’s recommendation.
Keep your stainless unit looking new by cleaning with a
good quality all-in-one stainless steel cleaner and polish
monthly. For best results use Claire® Stainless Steel
Polish and Cleaner. Comparable products are acceptable.
INTERIOR CLEANING
Disconnect power to the unit.
Frequent cleaning will remove surface contamination that
could lead to rust. Some installations may require cleaning
Clean the interior and all removed components using a
weekly.
mild nonabrasive detergent and warm water solution
applied with a soft sponge or non-abrasive cloth.
Do not clean with steel wool pads.
Rinse the interior using a soft sponge and clean water.
Do not use stainless steel cleaners polishes on
any glass surfaces.
Do not use any solvent-based or abrasive
cleaners. These types of cleaners may transfer taste to
Clean any glass surfaces with a non-chlorine glass
the interior products and damage or discolor the interior.
cleaner.
DEFROSTING
Do not use cleaners not specifically intended for
stainless steel on stainless surfaces (this
includes glass, tile and counter cleaners).
Under normal conditions this unit does not require manual
defrosting. Minor frost on the rear wall or visible through
the evaporator plate vents is normal and will melt during
each off cycle.
If there is excessive build-up of 1/4" (6 mm) or more,
manually defrost the unit.
Ensure the door is closing and sealing properly.
Cleaning 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
High ambient temperature and excessive humidity can
also produce frost.
! CAUTION
DO NOT use an ice pick or other sharp
instrument to help speed up defrosting. These
instruments can puncture the inner lining or
damage the cooling unit. DO NOT use any type of
heater to defrost. Using a heater to speed up
defrosting can cause personal injury and
damage to the inner lining.
NOTICE
The drain pan was not designed to capture the
water created when manually defrosting. To
prevent water from overflowing the drain pan,
place towels or other absorbent materials over
the interior drain trough (under the evaporator)
before defrosting.
To defrost:
1. Disconnect power to the unit.
2. Remove all products from the interior.
3. Prop the door in an open position (2 in. [50 mm]
minimum).
4. Allow the frost to melt naturally.
5. After the frost melts completely clean the interior and
all removed components. (See INTERIOR CLEANING).
6. When the interior is dry, reconnect power and turn unit
on.
Cleaning 2
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Cleaning Condenser
INTERVAL - EVERY SIX MONTHS
To maintain operational efficiency, keep the front grille
free of dust and lint, and clean the condenser when
necessary. Depending on environmental conditions, more
or less frequent cleaning may be necessary.
! WARNING
Disconnect electric power to the unit before
cleaning the condenser.
! WARNING
DO NOT touch the condenser fins. The condenser
fins are SHARP and can be easily damaged.
NOTICE
DO NOT use any type of cleaner on the
condenser unit.
1. Remove the grill (See GRILLE-PLINTH INSTALLATION).
2. Clean the condenser coil using a using a soft brush
with a “combing” action or vacuum cleaner. Do not
touch the condenser coil.
3. Install the grille.
Condenser
Cleaning Condenser 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Extended Non-Use
VACATION/HOLIDAY, PROLONGED SHUTDOWN
The following steps are recommended for periods of
extended non-use:
1. Remove all consumable content from the unit.
2. Disconnect the power cord from its outlet/socket and
leave it disconnected until the unit is returned to
service.
3. If ice is on the evaporator, allow ice to thaw naturally.
4. Clean and dry the interior of the unit. Ensure all water
has been removed from the unit.
5. The door must remain open to prevent formation of
mold and mildew. Open door a minimum of 2"
(50 mm) to provide the necessary ventilation.
WINTERIZATION
If the unit will be exposed to temperatures of 40°F (5°C)
or less, the steps above must be followed.
For questions regarding winterization, please
call U-Line at +1.800.779.2547.
! CAUTION
Damage caused by freezing temperatures is not
covered by the warranty.
Extended Non-Use 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Troubleshooting
• Evaporator: Refrigerant flowing through an evaporator
may sound like boiling liquid.
BEFORE CALLING FOR SERVICE
If you think your U-Line product is malfunctioning, read
the CONTROL OPERATION section to clearly understand
• Condenser Fan: Air moving through a condenser may
be heard.
the function of the control.
• Automatic Defrost Drain Pan: Water may be heard
If the problem persists, read the NORMAL OPERATING
dripping or running into the drain pan when the unit is
SOUNDS and TROUBLESHOOTING GUIDE sections below
in the defrost cycle.
to help you quickly identify common problems and
possible causes and remedies. Most often, this will resolve
the problem without the need to call for service.
IF SERVICE IS REQUIRED
TROUBLESHOOTING GUIDE
! DANGER
If you do not understand a troubleshooting remedy, or
ELECTROCUTION HAZARD. Never attempt to
your product needs service, contact U-Line Corporation
repair or perform maintenance on the unit
directly at +1.800.779.2547.
before disconnecting the main electrical power.
When you call, you will need your product Model and
Troubleshooting - What to check when problems occur:
Serial Numbers. This information appears on the Model
and Serial number plate located on the upper right or rear
Problem
Possible Cause and Remedy
wall of the interior of your product.
Digital Display
and Light Do Not
Work.
Ensure power is connected to the unit.
If the unit is cooling, it may be in Sabbath
mode.
NORMAL OPERATING SOUNDS
Interior Light
Does Not
Illuminate.
The light bulb may be defective.
If the unit is cooling, it may be in Sabbath
mode.
Light Remains on
When Door Is
Closed.
For glass door models, press the light icon
and close the door.
Check reed switch.
Unit Develops
Frost on Internal
Surfaces.
Frost on the rear wall is normal and will melt
during each off cycle.
If there is excessive build-up of 1/4" or
more, manually defrost the unit.
Ensure the door is closing and sealing
properly.
High ambient temperature and excessive
humidity can also produce frost.
Unit Develops
Condensation on
External
Surfaces.
The unit is exposed to excessive humidity.
Moisture will dissipate as humidity levels
decrease.
Digital Display
Functions, But
Unit Does Not
Cool.
Ensure the unit is not in “Showroom Mode.”
Momentarily unplug or interrupt power
supply to the unit.
Digital Display
Shows ER or E
Followed by a
Number.
E3 indicates the door may be opened too
long. Ensure the door is closing properly.
For other error codes contact U-Line
Customer Service.
All models incorporate rigid foam insulated cabinets to
provide high thermal efficiency and maximum sound
reduction for its internal working components. Despite this
technology, your model may make sounds that are
unfamiliar.
Normal operating sounds may be more noticeable because
of the unit’s environment. Hard surfaces such as cabinets,
wood, vinyl or tiled floors and paneled walls have a
tendency to reflect normal appliance operating noises.
Listed below are common refrigeration components with a
brief description of the normal operating sounds they
make. NOTE: Your product may not contain all the
components listed.
• Compressor: The compressor makes a hum or pulsing
sound that may be heard when it operates.
Troubleshooting 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Problem
Possible Cause and Remedy
Digital Display
Shows 1-16 or 99
A factory test mode may be enabled. Adjust
the temperature to 99 and press the LIGHT
icon.
Product Is
Freezing.
Because product in contact with the rear
wall may freeze, ensure no product is
touching the rear wall.
Adjust the temperature to a warmer set
point.
Product Is Not
Cold Enough.
Air temperature does not indicate product
temperature. See CHECKING PRODUCT
TEMPERATURE below.
Adjust the temperature to a cooler set point.
Ensure unit is not located in excessive
ambient temperatures or in direct sunlight.
Ensure the door is closing and sealing
properly.
Ensure the interior light has not remained
on too long.
Ensure nothing is blocking the front grille,
found at the bottom of the unit.
Ensure the condenser coil is clean and free
of any dirt or lint build-up.
6. After 24 hours, check the temperature of the water. If
required, adjust the temperature control in a small
increment (see CONTROL OPERATION).
Causes which affect the internal temperatures of
the cabinet include:
• Temperature setting.
• Ambient temperature where installed.
• Installation in direct sunlight or near a heat source.
• The number of door openings and the time the door is
open.
• The time the internal light is illuminated. (This mainly
affects product on the top rack or shelf.)
CHECKING PRODUCT TEMPERATURE
To check the actual product temperature in the
unit:
1. Partially fill a plastic (nonbreakable) bottle with water.
2. Insert an accurate thermometer.
3. Tighten the bottle cap securely.
4. Place the bottle in the desired area for 24 hours.
5. Avoid opening the unit during the testing period.
Troubleshooting 2
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
U-Line Corporation (U-Line) Limited Warranty
One Year Limited Warranty
For one year from the date of original purchase, this U-Line product warranty covers all parts and labor to repair or replace any part of the
product that proves to be defective in materials or workmanship. For products installed and used for normal residential use, material
cosmetic defects are included in this warranty, with coverage limited to 60 days from the date of original purchase. All service provided by ULine under the above warranty must be performed by U-Line factory authorized service, unless otherwise specified by U-Line. Service
provided during normal business hours.
Available Second Year Limited Warranty
Beyond the standard one year warranty outlined above, U-Line offers an extension of the one year warranty coverage for an additional
second year from the date of purchase, free of charge. To take advantage of this second year warranty, you must register your product with
U-Line within two months from the date of purchase at u-line.com providing proof of purchase.
Five Year Sealed System Limited Warranty
For five years from the date of original purchase, U-Line will repair or replace the following parts, labor not included, that prove to be
defective in materials or workmanship: compressor, condenser, evaporator, drier, and all connecting tubing. All service provided by U-Line
under the above warranty must be performed by U-Line factory authorized service, unless otherwise specified by U-Line. Service provided
during normal business hours.
Terms
These warranties apply only to products installed in any one of the fifty states of the United States, the District of Columbia, or the ten
provinces of Canada. The warranties do not cover any parts or labor to correct any defect caused by negligence, accident or improper use,
maintenance, installation, service, repair, acts of God, fire, flood or other natural disasters. The product must be installed, operated, and
maintained in accordance with the U-Line User Guide.
The remedies described above for each warranty are the only ones that U-Line will provide, either under these warranties or under any
warranty arising by operation of law. U-Line will not be responsible for any consequential or incidental damages arising from the breach of
these warranties or any other warranty, whether express, implied, or statutory. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion may not apply to you. These warranties give you specific legal
rights, and you may also have other rights which vary from state to state.
Any warranty that may be implied in connection with your purchase or use of the product, including any warranty of merchantability or any
warranty fit for a particular purpose is limited to the duration of these warranties, and only extends to five years in duration for the parts
described in the section related to the five year limited warranty above. Some states do not allow limitations on how long an implied warranty
lasts, so the above limitations may not apply to you.
•
The warranties only apply to the original purchaser and are non-transferable.
•
The second year and five year warranties cover products installed and used for normal residential or designated marine use only.
•
The warranties apply to units operated outside only if designed for outdoor use by model and serial number.
•
Replacement water filters, light bulbs, and other consumable parts are not covered by these warranties.
•
The start of U-Line’s obligation is limited to four years after the shipment date from U-Line.
•
In-home instruction on how to use your product is not covered by these warranties.
•
Food, beverage, and medicine loss are not covered by these warranties.
•
If the product is located in an area where U-Line factory authorized service is not available, you may be responsible for a trip charge
•
Units purchased after use as floor displays are covered by the limited one year warranty only and no coverage is provided for cosmetic
•
Signal issues related to Wi-Fi connectivity are not covered by these warranties.
or you may be required to bring the product to a U-Line factory authorized service location at your own cost and expense.
defects.
For parts and service assistance, or to find U-Line factory authorized service near you, contact U-Line:
8900 N. 55th Street, Milwaukee, WI 53223 • u-line.com • onlineservice@u-line.com • +1.800.779.2547
Copyright © 2014/2017 U-Line Corporation. All Rights Reserved. | Publication Number 30379 | 04/2017 Rev. K
Warranty 1
R/B LIGHT
L/T LIGHT
EVAP TEMP
COND FAN
L/T DOOR SWITCH
R/B DOOR SWITCH
AMBIENT TEMP
ZONE TEMP
EVAP TEMP
5
1
6
10
8
1
16
9
J9 J10
AN
D
NA
TE
N
G
CONTROL
BOARD
OPEN
FUSE
Y
ISP
TO
IN
RA
M
OG
PR
LA
42350_B WIRING DIAGRAM
10
1
NEUTRAL:
WHITE (115v)
DARK BLUE (220-240v)
BLUE (115V)
LIGHT BLUE (220V-240V)
(TO COMPRESSOR)
220-240 VOLT
CAP.
BLUE
RELAY
CAP
NEUTRAL:
WHITE (115v)
DARK BLUE (220-240v)
(TO COMPRESSOR)
GROUND:
GREEN or
GREEN W/ YELLOW
115 VOLT
RELAY
NEUTRAL
HOT
OVERLOAD
115
VOLT
PLUG
PLUG
220-240 VOLT
EMBRACO
COMPRESSOR
POWER CORD
ASSEMBLY
HOT:
BLACK (115v)
BROWN (220-240v)
GROUND:
GREEN or GREEN W/ YELLOW
EMBRACO COMPRESSOR
BROWN
GROUND:
GREEN W/ YELLOW
NEUTRAL:
DARK BLUE
HOT (LIGHT BLUE)
OVERLOAD
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Wire Diagram
Wire Diagram 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Product Liability
Field service technicians are authorized to make an initial
assessment in the event of reported damages. If there are
any questions about the process involved, the technician
should call U-Line for further explanation.
While inspecting for defects or installation issues, photos
should be taken to document any damages or issues
found.
During the assessment, if the service technician is able to
find the source of the damage and it can be resolved by
replacement of a part, the servicer is authorized to
replace the part in question. The part that caused the
damage must be returned to U-Line in its entirety. The
part must be clearly labeled with the serial number of the
unit it was removed from, the date, and the servicer who
removed the part.
If the service technician determines the damage is the
result of installation issues (water connection/drain, etc.),
the consumer would be notified and the issues shall be
resolved at the direction of the consumer.
If damage is evident and the service technician is unable
to find the source, U-Line must be contacted at 1-800799-2547 for further direction
8900 N. 55th Street • Milwaukee, WI 53223
T: +1.414.354.0300 • F: +1.414.354.354.5696
Website: www.u-line.com
Right product. Right place.
Right temperature Since 1962.
Product Liability 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Warranty Claims
warranty status. We also accept the following
information to verify warranty status:
The following information defines the parameters for filing
a warranty claim:
• New Construction Occupancy Documents
• Valid serial number needed
• Valid model number needed
• Narda (or equivalent) form or submitted online at
www.u-line.com
• Closing Paperwork
• Final Billing – Remodel
Noting all of the following on the warranty claim will be
considered proof of purchase, hard copy will not be
required:
• 60 day submittal deadline from date of completed
service
• Name of the selling Dealer
• Only one repair or unit per warranty claim
• Refrigerant should be labeled and included on the labor
submittal
• Door and water level adjustments are covered 30 days
from install date.
Serial Number Requirements:
14 30911 12 X X X X
Year
• Date of purchase/installation
• Order or Invoice number (if available)
• Description of document reviewed (i.e. store receipt,
closing paperwork, etc)
Parts and labor claims are paid separately. Indicate part
numbers and description for parts used in the warranty
repair. Include the purchase invoice and name of the parts
supplier used to procure the parts.
Month
A typical serial number is shown above. The first two
digits of the first segment, 14, represents the production
year. The number between the dashes, 12, represents the
production month. In most cases, warranty status can be
verified by the production date information within the
serial number.
• Alternatively, a Proof of Purchase (or equivalent) may
submitted with the warranty claim to document
Warranty Claims 1
Parts
2
1
U-ADA24RGLINT-00A
19
8
7
Item
18
9
16
14
15
12
13
32
26
31
17
3
4
6
25
21
22
5
10
27
Description
U-Line P/N
1
Anti tip bracket w/screws
80-54239-00
2
Back panel
80-54324-00
3
Compressor electricals only
80-54149-00
4
Compressor w/electricals
80-54150-00
5
Condenser assembly
80-54322-00
6
Condenser fan w/screws
80-54014-00
7
Control Housing
80-54273-00
8
Display module
80-54236-00
9
Door assembly w/hinges
80-54815-00
10 Drain pan w/double sided tape
80-54819-00
11 Drier
80-54055-00
12 Evaporator assembly
80-54275-00
13 Evaporator cover w/screws
80-54319-00
14 Evaporator fan
80-54321-00
15 Evaporator fan cover w/screws
80-54320-00
16 Gasket, door, injection molded
80-54213-00
17 Grille w/screws
80-54325-00
18 Hinges (2) w/screws
80-54208-00
19 LED light strip and cover assy
80-54000-00
20 Leg Levelers (4)
80-54201-00
21 Magnet w/bracket and screws
80-54749-00
22 Main board (no case or wires)
80-54008-00
23 Packaging
80-54209-00
24 Power cord
80-54171-00
25 Reed switch
80-54134-00
26 Thermistor (1 pc)
80-54006-00
27 Thermistor cover and pin
80-54237-00
28 Tool, leg leveler
80-54794-00
29 WIFI antenna
80-54804-00
30 Wire harness, board
80-54251-00
31 Wire shelf btm, w/clips(1)
80-54329-00
32 Wire shelf w/clips(1)
80-54328-00
20
Parts 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Ordering Replacement Parts
If you have a purchasing account, please utilize our
service website to order parts.
Orders may also be placed by Fax or phone. See our
contact information below:
www.U-LineService.com (with service login)
FAX Number: +1.414.354.5696
Phone Number: +1.800.779.2547
NOTICE
Use only genuine U-Line replacement parts. The
use of non-U-Line parts can reduce speed of ice
production, cause water to overflow from ice
maker mold, damage the unit, and void the
warranty.
Warranty parts will be shipped at no charge after U-Line
confirms warranty status. Please provide the model, serial
number, part number and part description. Some parts
will require color or voltage information.
If U-Line requires the return of original parts, we will
inform you when the parts order is taken. This
requirement will be noted on your packing list. A prepaid
shipping label will be included with the replacement part.
Please enclose a copy of the parts packing list and any
labor claims with your return. Please be sure the model
and serial numbers are legible on the paperwork. Tag the
part with the reported defect.
When ordering a non-warranty part, you will need an open
account and tax exemption on file at U-Line. Another
option would be to visit www.u-line.com to locate an
authorized parts distributor in your area.
Ordering Replacement Parts 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
System Diagnosis Guide
REFRIGERATION SYSTEM DIAGNOSIS GUIDE
System
Condition
Suction
Pressure
Suction
Line
Compressor
Discharge
Condenser
Capillary
Tube
Evaporator
Wattage
Normal
Normal
Slightly below
room
temperature
Very hot
Very hot
Warm
Cold
Normal
Overcharge
Higher than
normal
Very cold may
frost heavily
Slightly warm
to hot
Hot to warm
Cool
Cold
Higher than
normal
Undercharge
Lower than
normal
Warm-near
room
temperature
Hot
Warm
Warm
Extremely cold
near inlet Outlet below
room
temperature
Lower than
normal
Partial
Restriction
Somewhat
Warm - near
lower than
room
normal vacuum temperature
Very hot
Top passes
warm - Lower
passes cool
(near room
temperature)
due to liquid
Room
temperature
(cool) or
colder
Extremely cold
near inlet Outlet below
room
temperature
backing up
Lower than
normal
Complete
Restriction
In deep
vacuum
Room
temperature
(cool)
Room
temperature
(cool)
Room
temperature
(cool)
Room
temperature
(cool)
No refrigeration
Lower than
normal
No Gas
0 PSIG to 25"
Room
temperature
(cool)
Cool to hot
Room
temperature
(cool)
Room
temperature
(cool)
No refrigeration
Lower than
normal
System Diagnosis Guide 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Compressor Specifications
OVERLOAD PROTECTOR
STARTING RELAY
! DANGER
C
S
Electrocution can cause death or serious injury.
R
Burns from hot or cold surfaces can cause
serious injury. Take precautions when servicing
RELAY COVER
CAPACITOR
this unit.
Disconnect the power source.
ULIN_0368_A
EMX20CLC
Refrigerant
R600a
Voltage
Do not stand in standing water when working
Frequency
around electrical appliances.
Run Cap
115 - 127 VAC
60 Hz
12μF/165 VAC
Start Winding
6.7 Ohm at 77°F
Make sure the surfaces you touch are not hot or
Run Winding
12.6 Ohm at 77°F
frozen.
LRA
3.7 A
FLA
0.5 A
Do not touch a bare circuit board unless you are
Starting Device
wearing an anti-static wrist strap that is
Overload
grounded to an electrical ground or grounded
8EA14C
4TM142RFBYY-53
* All resistance readings are ±10%
water pipe.
Handle circuit boards carefully and avoid
touching components.
To measure the start winding resistance, measure across
the C and S pins.
To measure the run winding resistance, measure across
the C and R pins.
Also check S to R and you should get the sum of the run
and start windings.
To ensure the windings are not shorted, check the S and R
to ground.
Compressor Specifications 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Troubleshooting - Extended
NORMAL OPERATING SOUNDS
All models incorporate rigid foam insulated cabinets to
! CAUTION
Never attempt to repair or perform maintenance
on the unit until the main electrical power has
provide high thermal efficiency and maximum sound
reduction for its internal working components. Despite this
technology, your model may make sounds that are
unfamiliar.
been disconnected from the unit.
Normal operating sounds may be more noticeable because
SPECIFIC ERRORS AND ISSUES
The technically advanced diagnostic capabilities of the
of the unit’s environment. Hard surfaces such as cabinets,
wood, vinyl or tiled floors and paneled walls have a
tendency to reflect normal appliance operating noises.
electronic controls utilized on the 1200 and 2200 series
units allows for easy and thorough troubleshooting.
Listed below are common refrigeration components with a
brief description of the normal operating sounds they
Navigation of the control is the key and is explained in the
make. NOTE: Your product may not contain all the
CONTROL OPERATION section of the manual, along with
components listed.
control button layout, control function descriptions, a
service mode menu and service menu selection
explanations.
Verification of temperature and thermistor performance
can be identified by directly viewing thermistor readings in
the service mode.
Component failure issues can be identified through service
mode menu #19, “Component Testing.” Individual
• Compressor: The compressor makes a hum or pulsing
sound that may be heard when it operates.
• Evaporator: Refrigerant flowing through an evaporator
may sound like boiling liquid.
• Condenser Fan: Air moving through a condenser may
be heard.
components can be switched on and off to check for both
proper function of a specific component and also delivery
• Automatic Defrost Drain Pan: Water may be heard
of supply voltage to the components through the relays
dripping or running into the drain pan when the unit is
and DC outputs located on the relay/power board.
in the defrost cycle.
Included in this section are some diagnostic tips and of
Solenoid Valves: An occasional clicking sound may be
course, if additional help is required please contact the
heard as solenoid valves are operated.
U-Line Corp, “Customer Care Facility” at +1.800.779.2547
for assistance.
Troubleshooting - Extended 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
TROUBLESHOOTING GUIDE
Concern
Potential Causes
Suggested Remedy
Not Cooling
Compressor overheating
Verify proper air flow through condenser. Is condenser clean?
Confirm condenser fan operation.
Confirm proper compressor operating voltage. Use #19, Component
Testing in Service Mode.
Compressor not operating
Confirm proper compressor operating voltage. Use #19, Component
Testing in Service Mode.
Compressor operating - no cooling
Refer to System Diagnosis Guide.
Test overload and relay, replace as needed.
Frozen Product
Frost Buildup
Inside Unit
Display Not
Working
Evaporator fan not operating
Use #19, Component Testing in Service Mode.
Control set too cold
Adjust Set Point Temp accordingly.
Review logged error codes
Refer to #14, Error Log in Service Mode.
Thermistor failure
Check Error Log in Service Mode, OHM thermistor.
Door Ajar or Restricted from Closing
Check door clearance to adjoining cabinetry. Check distribution of
product in unit.
Evaporator fan not operating
Use Relay Toggle, Component Testing in Service Mode.
Thermistor failure
Check Error Log.
Unit placed in Sabbath mode?
Press and hold
Display unplugged
Verify that both ends of the display wiring are firmly connected.
for 5 seconds to check.
Display wiring broken or damaged
Perform continuity test of wiring and replace as needed.
Internal Lights
Not Working
Control Setting
Unit set to Sabbath Mode. Press and hold
Door switch misaligned or defective
Check the function of reed switch and door magnet adjustment.
Noisy
Refrigeration tubing touching cabinet
Carefully reposition tubing.
Fan blade obstruction (wiring, foam
insulation, packaging material)
Remove obstruction.
for 5 seconds to check.
Troubleshooting - Extended 2
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
MAIN CONTROL
Testing The Main Control
The main control board is very robust and is rarely the
If the main control is suspected of being faulty, the
cause of system issues. It is important to fully diagnose
following procedure should be performed to verify main
the board for any suspected failures before attempting to
control for functionality.
remove the board for replacement or service. Follow the
guidelines below to fully test and diagnose the main
control.
Relay & DC Outputs
One of the primary functions of the main control is to
operate the multiple relay and DC outputs during each
Power Fault
cycle. Verify proper operation of these relays using the
If the unit does not (or seems to not) power on, follow the
following procedure.
flow chart below to help diagnose the issue. Before
beginning it is important to first verify the unit is not
simply set to sabbath mode.
1. Enter “Relay Toggle” through the service menu.
NOTICE
Check Voltage
At Wall Outlet
No Voltage
Alert Customer
Of Power Failure
Frequently toggling the compressor relay could
force the compressor into overload. The
compressor will automatically deactivate during
Voltage
an overload and will remain deactivated until the
overload switch cools. This could take some
Verify Voltage At
Main Control
Voltage Input
No Voltage
Replace
Power Cord
time. It is important to allow the compressor at
least 5 minutes off time between relay cycles.
Voltage
2. Toggle the relay. Its related component should
Check Fuse F1
For Continuity
No Continuity
Replace
Fuse
activate / deactivate with the switching of the relay. If
it does not, test component.
Continuity
Other Suspected Main Control Faults
Connect Test Display
Cycle Power And Check
For Operation
Operating
Inspect
Customer UI
and Data Cable
but the unit continues to have operating issues, it is most
likely due to a configuration error. Configuration errors
Not Operating
Is the Reed
Switch Operating
Properly?
If other components have been ruled out as being faulty
can be cleared by restoring the unit to its factory default
setting. Factory defaults may be restored through the
Yes
Replace Main
Board
service menu.
No
! CAUTION
Replace
Reed Switch
Precautions must be taken while working with
live electrical equipment. Be sure to follow
proper safety procedures while performing tests
on live systems.
Troubleshooting - Extended 3
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
REED SWITCH
A reed switch is used to monitor door state. When the
door is closed magnetic force pulls the reed to its contact
and closes the circuit which turns the light and display off.
When the door is open the reed pulls away from the
contact and opens the circuit. If the door is left open for
longer than 5 minutes, the switch will trigger an error code
and set an audible warning.
Magnet Away From Switch
(Door Open)
(Switch Open)
Magnet Close To Switch
(Door Closed)
(Switch Closed)
Troubleshooting - Extended 4
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Control Operation - Service
UI BUTTON LAYOUT
1
2
3
4
5
6
7
1. Hidden Button
-Accesses Service Menu
-No LED directly above. All LEDs turn on with button
activation except #7.
2. Up Button
-Increases temperature
-Navigates through service menu
-LED activated with button activation.
3. Down Button
-Decreases temperature
-Navigates through service menu
-LED activated with button activation
4. Light Button
-Activates light for 3 hours on select models
-Used to select items in service menu
-LED activated with button activation
5. Power Button
-Turns unit off/on
-LED activated with button activation (only turning unit
off)
6. Clean Button
-Activates Clean Cycle on CLR models
-LED activated with button activation
7. LED
-No button
Control Operation - Service 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
CONTROL FUNCTION QUICK GUIDE
FUNCTION
COMMAND
DISPLAY/OPTIONS
ON/OFF
Press
and release
Unit will immediately turn ON or OFF
Press
and release to leave interior light
Glass door wine captains and beverage centers
Toggle lights
Adjust refrigerator
temperature
on for 3 hours
only.
When the “F” or “C” in the display is flashing,
Push
and release
or
push
or
to adjust the set point
temperature.
View temperature in unit
Push
Toggle between F/C
Hold the
and release the together
and
and
for five seconds
The display will flash and then toggle from set
point to temperature in unit.
The display will change units.
DOOR ALERT NOTIFICATION
When the degree symbol is flashing the unit will allow the
When the door is left open for more than 5 minutes:
use of the control for demonstrations. The unit can be left
in this mode indefinitely.
•
An audible tone will sound for several seconds every
minute.
•
“dr” will appear in display.
Close door to silence alert and reset.
SERVICE MODE
This mode has options available for service diagnostics.
To enter the mode hold the hidden key for 10 seconds.
The display will show “0.” When in this mode use the up
VIEWING ACTUAL TEMPERATURE
and down arrows to select the desired option. The LIGHT
In viewing temperature in these modes any offsets are
key is the ENTER key and will initiate the function. If
taken into account. This means that if you place a therm-
changing a setting, you must press the LIGHT key again
istor in a known temperature, let’s say ice water, it may
to retain the changed setting. To exit the service mode
not read the 32°F that you would assume. If the control
scroll to option “0” and press the LIGHT key. After five
offset was preset at -3°F while you placed the thermistor
minutes of not touching any keys the mode will also exit
in an icebath, the actual thermistor reading when viewing
automatically.
actual temperature would read 35°F. In the unit this would
cause the cabinet to push itself 3° cooler. To view pure
thermistor readings you must go into the service menu
and choose the correct option.
To view the thermistor temperature, push and release the
up and down keys. The display will show the corrected
refrigerator temperature.
SHOWROOM MODE
This mode is designed to show units in a display environment. When in this mode the only functions will be the
control and cabinet lights. The compressor, fans, etc. will
not operate. To enter/exit this mode hold the light key
and the power key for 5 seconds. The display will flash
once and beep and the degree symbol will begin to flash.
Control Operation - Service 2
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
SERVICE MODE GUIDE
#
Service Mode Menu Item
SERVICE MODE GUIDE
1. THERMISTOR 1 — ZONE
This shows the pure thermistor reading with no
offsets taken into account.
1
View thermistor #1 (no offsets)
2
View thermistor #2 (no offsets)
3
View thermistor #3 (no offsets)
4
View thermistor #4 (no offsets)
5
Adjust thermistor #1 offset
6
Adjust thermistor #2 offset
7
Adjust thermistor #3 offset
4. Does not apply to this model.
8
Adjust thermistor #4 offset
5. THERMISTOR 1 — ZONE OFFSET
9
View thermistor #2 set point no offsets
10
View thermistor #3 set point no offsets
11
View thermistor #4 set point no offsets
12
Adjust defrost interval 3 to 24 hours
13
Adjust defrost duration 0 to 99 minutes
14
View error log
15
Clear error log
16
Adjust thermistor #1 differential
17
Adjust evaporator fan delay in minutes (start of cooling
cycle) 0 - 99 minutes
18
Adjust evaporator fan delay in minutes (after cooling
cycle stops) 0 - 99 minutes
19
Individual component toggle
20
Model number indicator
7. THERMISTOR 3 — AMBIENT OFFSET
Not adjustable.
21
Light all LED segments of display
8. Does not apply to this model.
22
View defrost cycles
23
View compressor run time
24
Activate defrost/harvest
25
Restore factory defaults
9. THERMISTOR 2 — SET POINT MINUS
OFFSET
This shows the thermistor reading with offsets
taken into account.
26
View software version - main board
10. Does not apply to this model.
27
View software version - user interface
11. Does not apply to this model.
28
Login period
29
Factory test mode
0
Exit service mode
12. ADJUST DEFROST INTERVAL — 3 TO 24
HOURS
This will adjust the interval between defrosts
from 3 to 24 hours. Adjusting from the factory
settings may cause undesired temperature in
the refrigerator section.
NAVIGATE SERVICE MODE
Use up or down arrows to scroll through the menu.
Use the light bulb key to enter or exit menu. If values
have been changed, they will be saved when exiting.
2. THERMISTOR 2 — EVAPORATOR
This shows the pure thermistor reading with no
offsets taken into account.
3. Does not apply to this model.
(DO NOT MAKE AN ADJUSTMENT TO THIS WITHOUT
CONTACTING TECH LINE: 800-779-2547)
This calibration is only to be used if actual
temperature at thermistor #1 is off from set
point.
By adjusting the offset higher we can force the
unit to drive the temperature down below the set
point. (example: adjusting from 0 to +2 will drop
the unit temperature 2 degrees)
6. THERMISTOR 2 — EVAPORATOR OFFSET
(DO NOT MAKE AN ADJUSTMENT TO THIS WITHOUT
CONTACTING TECH LINE: 800-779-2547)
13. ADJUST DEFROST DURATION — 0 TO 99
MINUTES
The length of the defrost can be adjusted 0 to 99
minutes long. The other defrost parameters still
apply. Lengthening a defrost may cause higher
than normal temperatures in the refrigerator
section.
Control Operation - Service 3
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
14. VIEW ERROR LOG
A list of the errors in the order they occurred will
scroll once on the display. All errors are logged
in memory. Only door error is displayed on the
display and has an audible signal.
E0: Door 1 (upper) open.
E1: Thermistor 1 open.
E2: Thermistor 2 open.
E3: Thermistor 3 open.
E4: Thermistor 4 open (Does not apply to this
model).
Thermistor 1 shorted.
Thermistor 2 shorted.
Thermistor 3 shorted.
Thermistor 4 shorted (Does not apply to this
model).
E9: Door 2 (lower) open.
P1: Pump Circuit open (Does not apply to this
model).
E5:
E6:
E7:
E8:
15. CLEAR ERROR LOG
To clear errors, press and hold
when CLR is flashing.
(5 seconds)
16. THERMISTOR — 1 DIFFERENTIAL
This number should not be adjusted.
17. EVAPORATOR FAN DELAY IN MINUTES —
ON
“Fan Delay On” is the amount of time in minutes
the fan will be delayed from starting from the
beginning of a cooling cycle. Adjustable 0-99
minutes.
18. EVAPORATOR FAN DELAY IN MINUTES —
OFF
“Fan Delay Off” is the amount of time in minutes
the fan will continue to run at the end of a
cooling cycle. Adjustable 0-99 minutes.
19. INDIVIDUAL COMPONENT TOGGLE
Display #
Relay/Output
0
Exit
2
Relay 2
3
Relay 3
4
Relay 4
5
Relay 5
6
Relay 6
7
Relay 7
8
DC Output 1
9
DC Output 2
10
DC Output 3
11
DC Output 4
12
DC Output 5
20. MODEL NUMBER INDICATOR
Displays the two-digit model number of the
specific unit. See model list table.
21. LIGHT ALL LED SEGMENTS
This will illuminate all the LEDs on the display to
ensure they work properly.
22. VIEW DEFROST CYCLES
Displays the number of defrosts that have
occurred in the past 24 hours.
23. VIEW COMPRESSOR RUNTIME
This will show the number of minutes the
compressor has run in the prior cycle (or
current cycle if the compressor was running
when service mode was entered).
24. ACTIVATE DEFROST/HARVEST
Turns on the hot gas bypass valve allowing hot
gas to circulate through the evaporator causing
frost to melt.
25. RESTORE FACTORY DEFAULTS
Will restore all adjustable functions to their
factory settings.
26. SOFTWARE VERSION — MAIN BOARD
Displays software version of the main control
board.
27. SOFTWARE VERSION — USER INTERFACE
Displays software version of the user interface.
28. LOG IN PERIOD
Factory use only - do not adjust.
29. FACTORY TEST MODE
Should be 0.
0. EXIT SERVICE MODE
SEE RELAY/OUTPUT CHART
Control Operation - Service 4
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
MODEL LIST
1000
1215R
MODEL
INDICATOR
07
2000 (120V)
2218R
MODEL
INDICATOR
05
2000 (230V)
2245R
MODEL
INDICATOR
55
1215WC
12
2218RGL
04
2245DC
54
1224BEV
13
2218WC
06
2245WC
56
1224DWR
08
2224BEV
00
2260DC
50
1224R
14
2224R
02
2260R
52
1224RF
09
2224RGL
01
2260RDC
51
1224RSOD
10
2224WC
03
2260WC
53
1224WC
15
2224ZWC
59
2260ZWC
58
CLR1215
18
ADA24R
17
CO1224F
19
1224FZR
11
PROGRAMMING THE UNIT TO CORRECT
MODEL NUMBER
1. Disconnect the unit from power source.
2. Push and hold the U-Line button.
3. While still holding the U-Line button, plug the
unit into the appropriate power source.
4. When the flashing digits appear (3-5 seconds),
use the up and down arrow buttons to select the
appropriate model number*.
or
*(See Above “Model List”)
5. Press the light bulb button once.
6. The display will blink, and then will appear as the
programmed display.
Control Operation - Service 5
vl2
N/A
N/A
Defrost Heater
N/A
N/A
N/A
N/A
N/A
N/A
2260R
2260RDC
2260WC
2260ZWC
1224FZR
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
vl2
2260DC
Hot Gas Valve
Hot Gas Valve
Hot Gas Valve
N/A
N/A
N/A
N/A
2224ZWC
N/A
N/A
2245WC
N/A
2224WC
N/A
N/A
N/A
2224RGL
N/A
N/A
N/A
N/A
N/A
2224R
N/A
N/A
N/A
N/A
Pan Heater
Water Valve
N/A
N/A
N/A
Pan Heater
N/A
2245RDC
N/A
2224BEV
N/A
N/A
Ice Maker 1
Pump
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Relay 4
2245R
N/A
N/A
2218WC
N/A
N/A
2218RGL
Ice Maker 2
CO1224F
2218R
N/A
CLR1215
1224RSOD
N/A
N/A
1224RF
N/A
N/A
1224R
ADA24R
N/A
1224DWR
1224WC
N/A
Mullion
Heater
N/A
N/A
N/A
N/A
N/A
N/A
124BEV
N/A
1215R
Relay 3
1215WC
Relay 2
Name
N/A
vl1
N/A
N/A
N/A
N/A
N/A
N/A
N/A
vl1
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Hot Gas Valve
Hot Gas Valve
N/A
N/A
N/A
Hot Gas Valve
N/A
N/A
N/A
N/A
N/A
Relay 5
Compressor
Compressor
Condenser
Fan
Compressor
Compressor
Compressor
Compressor
Compressor
Compressor
Compressor
Compressor
Compressor
Compressor
Compressor
Compressor
Compressor
Compressor
Compressor
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Compressor
Compressor
Condenser
Fan
N/A
Compressor
Compressor
Compressor
Compressor
Compressor
Compressor
Compressor
Compressor
Compressor
Relay 7
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Relay 6
Light
Top Light
Light
Light
Light
Light
Light
Light
Light
Top Light
Light
Light
Light
Light
Light
Light
Light
Light
Light
Light
Light
Light
Light
Light
Top Light
Light
Light
Light
DC
Output 1
Relay / Output Chart
Evaporator Fan
N/A
Evaporator Fan
Evaporator Fan
Evaporator Fan
Evaporator Fan
Evaporator Fan
Evaporator Fan
Evaporator Fan
N/A
Evaporator Fan
Evaporator Fan
Evaporator Fan
Evaporator Fan
Evaporator Fan
Evaporator Fan
Evaporator Fan
Evaporator Fan
N/A
Evaporator Fan
Evaporator Fan
Evaporator Fan
Evaporator Fan
Evaporator Fan
Evaporator Fan
Evaporator Fan
Evaporator Fan
Evaporator Fan
DC
Output 2
N/A
Condenser Fan
Condenser Fan
Condenser Fan
Condenser Fan
Condenser Fan
Condenser Fan
Condenser Fan
Condenser Fan
Condenser Fan
Condenser Fan
Condenser Fan
Condenser Fan
Condenser Fan
Condenser Fan
Condenser Fan
Condenser Fan
Condenser Fan
N/A
Condenser Fan
Condenser Fan
Condenser Fan
Condenser Fan
Condenser Fan
Condenser Fan
Condenser Fan
Condenser Fan
Condenser Fan
DC
Output 3
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
DC
Output 4
N/A
Bottom Light
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Bottom Light
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Bottom Light
N/A
N/A
N/A
DC
Output 5
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Control Operation - Service 6
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Thermistors
1000 Series Self Preservation Mode:
Thermistors are used for various temperature readings.
minutes.
The unit will cycle on for 10 minutes then off for 40
Thermistors provide reliable temperature readings using a
resistance which varies based on surrounding
temperatures. If a faulty thermistor is suspected it may
be tested using an accurate ohmmeter.
Both thermistors in the unit are identical. If a thermistor is
suspected of being defective, the resistance can be
verified. Place the thermistor in an ice water bath, the
resistance should read 16.1k OHMs +/-5% on your meter.
Evaporator Thermistor
If the evaporator thermistor fails, the unit will rely on a
preset defrost timer during defrost cycles. The unit will
otherwise operate normally. Refer to defrost section.
Thermistor Resistance Data
Temp (F)
Temp (C)
Nominal Resistance
(OHMS)*
Thermistor connections must be kept clean. A thermistor
-40
-40
169157
connection that has become corroded can cause
-31
-35
121795
resistance values from the thermistor to change as they
-22
-30
88766
pass through a dirty connection to the board.
-13
-25
65333
-4
-20
48614
It is for that reason that we apply dielectric grease to all of
5
-15
36503
our thermistor connections. Dielectric grease will help to
14
-10
27681
keep thermistor connections clean and dry.
23
-5
21166
32
0
16330
41
5
12696
50
10
9951
59
15
7855
68
20
6246
Thermistor error information can be found in the Control
77
25
5000
Operations - Service section.
86
30
4029
95
35
3266
This unit has two thermistors.
104
40
2665
If you change a thermistor in the unit please re-apply
dielectric grease to the connection. If you encounter a
dirty thermistor connection, you should replace the
thermistor and the thermistor harness.
113
45
2186
Thermistor one (Zone):
122
50
1803
Located along the right hand side wall. It is used to
131
55
1495
maintain the operating temperature within that zone.
140
60
1247
Thermistor two (Evaporator):
149
65
1044
158
70
879
167
75
743
176
80
631
Located on the evaporator. It is used for defrost.
THERMISTOR FAILURE
Zone Thermistor
* (+/-5%)
If the zone thermistor in the unit fails, the unit will
continue to cool in a backup mode (Self Preservation
Mode) to preserve the integrity of the contents. The unit
will otherwise operate normally.
Thermistor 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Defrost
The models below have automatic or frost free design and do not require manual defrosting under normal conditions.
Defrost Settings
Base Model
Variant(s)
Compressor Run Time
Between Defrost (Hours)
Duration in Minutes
(Maximum)
Stop Temperature
°F (°C)
1224
RF
12
45
15 (-9)
1215/1224/2218/2245/
2224/2260
WC, ZWC
12
45
45 (7)
1215/1224/2218/2245/
2224/2260
R, RSOD, RDC,
BEV, DC, DWR, RGL
12
45
42 (6)
CO29
F
12
18
n/a
CO1224
F
12
18
45 (7)
1224FZR
Freezer Mode
6
45
42(6)
1224FZR
Refrigerator Mode
12
45
42(6)
Duration in Minutes
(Maximum)
Stop Temperature
°F (°C)
The defrost settings for 3000 series models are determined by zone.
Defrost Settings by Zone (3000 Series)
Zones
Compressor Run Time
Between Defrost (Hours)
Duration in Minutes
(Minimum)
Beverage/Drinks
12
5
60
42 (6)
Market/Fresh
12
5
60
42 (6)
Root/Root Cellar
12
5
60
45 (7)
Pantry
12
5
60
42 (6)
White Wine
12
5
60
45 (7)
Red Wine
12
5
60
45 (7)
Sparkling Wine
12
5
60
45 (7)
Polar
6
5
20
42 (6)
Deli
12
5
60
42 (6)
Defrost 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Remove Fan and Cover
Evaporator Fan Replacement
CONVECTION COOLING
steps below.
Should an evaporator fan need to be replaced follow the
This unit is equipped with an advanced convection cooling
system. Convection cooling stabilizes cabinet
temperature, cools product faster and increases energy
efficiency.
Evaporator Fan
The evaporator fan is responsible for circulating warm air
1. Remove any product from the unit.
2. Uninstall unit.
3. Disconnect power to the unit.
from the refrigeration zone, past the evaporator and back
into the refrigerated zone.
4. Remove the rear panel from unit.
The evaporator fan is factory set to have a 1 minute delay
5. Disconnect fan electrical connection to the fan which
at the beginning of a cooling cycle. This delay gives the
must be changed.
evaporator time to cool properly before warm air is passed
over it. The fan will continue to run for an additional 2
minutes at the end of a cooling cycle. Fan delay times can
be modified through the service menu.
Evaporator fan operation is also determined by door
switch state. If the door switch circuit opens, the fan will
6. Remove insulating foam from refrigerant line passthrough hole as needed to gain clearance for the fan
plug.
7. Remove shelf clips.
stop. When the door switch circuit is closed the fan will
either continue running with the cooling cycle, or if not
8. Remove internal shelving.
currently cooling, the fan will run for 1 minute to circulate
air and clear any condensation that may have appeared
9. Remove thermistor cover.
on glass doors and shelves.
10.Remove two evaporator cover screws from top of
Note: If the unit is set to sabbath mode, the evaporator
evaporator cover and two from the bottom.
fan will no longer respond to the state of the door switch.
In order to operate efficiently, the evaporator fan blade
and vents should be unobstructed and free of any dust
buildup.
The 3060 is a dual zone unit made up of two
independently controlled cooling zones. The 3060 can
contain wine captains, beverage centers and refrigerators,
either paired together or any combination there of.
Evaporator Cover
Screws
Remove Fan and Cover 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
11.While pulling the evaporator cover clear of the unit, it
may be necessary to use your free hand to manipulate
the fan plug end through the pass-through hole.
12.Remove the 4 screws mounting the fan shroud to the
evaporator plate.
Air Flow
13.Remove and replace fan. Take special care to properly
route fan wire.
NOTICE
Fan must be oriented to pull air in through lower
evaporator cover vents and push air out at fan
mounting location.
14.Installation is the reverse of removal.
15.Use sealant gum to seal any holes in the rear of the
unit before replacing the rear cover.
16.Reinstall the unit taking care to level, center and
secure as you found it.
Remove Fan and Cover 2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising