advertisement
▼
Scroll to page 2
of 96
Sub-Zero Design Guide Contents 3 Built-In Refrigeration 38 PRO 48 Refrigeration 44 Integrated Refrigeration 54 Wine Storage 84 Undercounter Refrigeration 94 Sub-Zero Warranties Features and specifications are subject to change at any time without notice. Visit subzero.com/specs for the most up-to-date information. IMPORTANT NOTE: Throughout this guide, dimensions may vary by ± 1/8" (3). Dimensions in parentheses are millimeters unless otherwise specified. BUILT-IN REFRIGERATION BUILT-IN Built-In Refrigeration Energy efficient; many models are ENERGY STAR® qualified. • Advanced water filtration and air purification systems. • NEW! French door models requires less space for door clearance to accommodate virtually any-size kitchen. • Four distinct design approaches: framed, overlay, flush inset and stainless steel. NEW! Internal dispenser models provide ice and chilled water inside the refrigerator. • Handle options coordinate with handles of Wolf cooking products. Crisper and deli drawers form a lower-temperature zone for produce and meats. • Dual refrigeration; two compressors preserve food’s goodness in two sealed compartments. Flip-up grille provides easy access for quick routine maintenance. • All models are Star-K certified. KEY FEATURES • • • PRO 48 • For the built-in line, Sub-Zero designers and engineers took a fresh look at everything, inside and out. Exterior refinements include redesigned grilles and lower-profile hinges. Inside, new technology in food preservation makes the builtin line nothing short of revolutionary. BUILT-IN MODELS INTEGRATED BI-36R BI-36RG BI-36F BI-30U BI-30UG BI-36U BI-36UG WINE BI-36UFD BI-42UFD BI-36S BI-42S(ID) BI-42SD BI-48S(ID) BI-48SD UNDERCOUNTER subzero.com/specs | 3 BUILT-IN BUILT-IN REFRIGERATION PRO 48 Built-In Design Options FRAMED OVERLAY For the classic Sub-Zero look, choose framed custom door panels that contrast with the stainless steel full-length handles and louvered grille (shown). The framed application is an overlay model with framed design features. Panel, grille and handle options are available. Custom overlay door panels can be combined with unique handle hardware for design flexibility. Shown with pro handle option to complement Wolf ranges. Customize with panel, grille and handle options. Panels | Custom panels, stainless steel or white enamel. Grille | Classic louvered grille insert or solid custom panel for 84" (standard), 83" or 88" overall unit height. Dual wide grille for dual installations. Panels | Custom panels or stainless steel. Grille | Solid custom panel or pro louvered grille for 84" (standard), 83" or 88" overall unit height. Dual wide grille for dual installations. Handles | Custom, tubular or pro handles. UNDERCOUNTER WINE INTEGRATED Handles | Full-length standard or extended. Framed. 4 | Sub-Zero Customer Care 800.222.7820 Overlay. BUILT-IN REFRIGERATION BUILT-IN Built-In Design Options FLUSH INSET STAINLESS STEEL The flush inset design option allows for flush door and grille panels and custom handle hardware. Shown with tubular handle option to match Wolf built-in ovens. The flush inset application is an overlay model with flush inset panels. Customize with panel, grille and handle options. For a professional look, classic stainless steel models require no customization. To complement the look of Wolf ranges, choose the pro handle option (shown). Grille and handle options are available. Grille | Solid custom panel or pro louvered grille for 84" (standard), 83" or 88" overall unit height. Dual wide grille for dual installations. Grille | Pro louvered grille for 84" (standard), 83" or 88" overall unit height. Dual wide grille for dual installations. PRO 48 Panels | Custom panels or stainless steel. Handles | Tubular or pro handles. Handles | Custom, tubular or pro handles. INTEGRATED WINE UNDERCOUNTER Flush inset. Stainless steel. subzero.com/specs | 5 BUILT-IN BUILT-IN REFRIGERATION Overall Dimensions ALL REFRIGERATOR / ALL FREEZER 26 3/16" (665) PRO 48 36" (914) 84" (2134) 73 3/4" INTEGRATED (1873) HEIGHT DIMENSIONS ± 1/2" (13) 4" (102) 23 7/8" (606) 14 1/8" (359) 37 1/4" WINE (946) 2 3/8" (60) UNDERCOUNTER Models BI-36R, BI-36RG and BI-36F. 6 | Sub-Zero Customer Care 800.222.7820 23 7/8" (606) Overall dimensions are based on stainless steel models. For flush inset applications, add 1/2" (13) to door clearance dimensions. BUILT-IN REFRIGERATION BUILT-IN Overall Dimensions OVER-AND-UNDER 26 3/16" (665) 30" (762) 84" (2134) 50 3/4" 50 3/4" (1289) (1289) 23" 23" (584) (584) HEIGHT DIMENSIONS ± 1/2" (13) 23 7/8" (606) 23 7/8" (606) 23 7/8" 23 7/8" (606) (606) 12 1/8" (308) (600) 4" (102) INTEGRATED 4" (102) PRO 48 84" (2134) HEIGHT DIMENSIONS ± 1/2" (13) 23 5/8" 26 3/16" (665) 36" (914) 14 1/8" (359) 311/4" (796) 23 5/8" (600) 37 1/4" (946) WINE 2 3/8" (60) 2 3/8" (60) Models BI-30U and BI-30UG. Models BI-36U and BI-36UG. UNDERCOUNTER subzero.com/specs | 7 BUILT-IN BUILT-IN REFRIGERATION Overall Dimensions OVER-AND-UNDER 26 3/16" (665) INTEGRATED PRO 48 36" (914) 26 3/16" (665) 42" (1067) 84" 84" (2134) (2134) 50 3/4" 50 3/4" (1289) (1289) 23" 23" (584) (584) HEIGHT DIMENSIONS ± 1/2" (13) 4" (102) HEIGHT DIMENSIONS ± 1/2" (13) 23 7/8" (606) 4" (102) 23 7/8" 23 7/8" (606) (606) 8" 9" (203) (229) 23 5/8" 191/2" 23 5/8" (495) (600) (600) 221/4" WINE (565) 2 3/8" (60) UNDERCOUNTER Model BI-36UFD. 8 | Sub-Zero Customer Care 800.222.7820 2 3/8" (60) Model BI-42UFD. 23 7/8" (606) BUILT-IN REFRIGERATION BUILT-IN Overall Dimensions SIDE-BY-SIDE 26 3/16" (665) 36" (914) 26 3/16" (665) 42" (1067) 84" (2134) 73 3/4" 73 3/4" (1873) (1873) 4" (102) HEIGHT DIMENSIONS ± 1/2" (13) 23 7/8" (606) 4" (102) (606) (606) 7 1/2" (191) 8 3/4" (222) 23 7/8" (606) 23 7/8" 23 7/8" 7 1/4" (184) INTEGRATED HEIGHT DIMENSIONS ± 1/2" (13) PRO 48 84" (2134) 10 3/8" (264) 221/4" 26 1/4" (565) (668) WINE 2 3/8" (60) 2 3/8" (60) Model BI-36S. Model BI-42S, BI-42SID and BI-42SD. UNDERCOUNTER subzero.com/specs | 9 BUILT-IN BUILT-IN REFRIGERATION Overall Dimensions SIDE-BY-SIDE 26 3/16" (665) PRO 48 48" (1219) 84" (2134) 73 3/4" INTEGRATED (1873) HEIGHT DIMENSIONS ± 1/2" (13) 4" (102) 23 7/8" (606) 8 3/8" (213) 11 5/8" (295) 30" WINE (762) 2 3/8" (60) UNDERCOUNTER Model BI-48S, BI-48SID and BI-48SD. 10 | Sub-Zero Customer Care 800.222.7820 23 7/8" (606) BUILT-IN REFRIGERATION BUILT-IN Specifications BUILT-IN MODELS INTERIOR CAPACITY ALL REFRIGERATOR / ALL FREEZER BI-36R BI-36RG BI-36F BI-30U BI-30UG BI-36U BI-36UG BI-36UFD BI-42UFD SIDE-BY-SIDE 23.5 (665) 23.4 (663) 22.7 (643) R CU FT (L) F CU FT (L) 13.2 (374) 13.1 (371) 16.4 (464) 16.3 (462) 15.7 (445) 18.3 (518) 4.2 (119) 4.2 (119) 5.3 (150) 5.3 (150) 5.3 (150) 6.4 (181) R CU FT (L) F CU FT (L) 12.4 (351) 16.3 (462) 15.8 (447) 16.0 (453) 19.1 (541) 18.6 (527) 18.8 (532) 8.2 (232) 8.0 (227) 7.9 (224) 7.9 (224) 9.8 (278) 9.6 (272) 9.6 (272) ALL REFRIGERATOR / ALL FREEZER BI-36R BI-36RG BI-36F OVER-AND-UNDER BI-30U BI-30UG BI-36U BI-36UG BI-36UFD BI-42UFD SIDE-BY-SIDE BI-36S BI-42S BI-42SID BI-42SD BI-48S BI-48SID BI-48SD LB (KG) 420 (191) 430 (195) 406 (184) LB (KG) 462 (210) 476 (216) 515 (234) 529 (240) 529 (240) 582 (264) LB (KG) 538 (244) 582 (264) 608 (276) 608 (276) 630 (286) 656 (298) 656 (298) Shipping weights are based on stainless steel models. INTEGRATED BI-36S BI-42S BI-42SID BI-42SD BI-48S BI-48SID BI-48SD F CU FT (L) PRO 48 OVER-AND-UNDER SHIPPING WEIGHT R CU FT (L) WINE UNDERCOUNTER subzero.com/specs | 11 BUILT-IN BUILT-IN REFRIGERATION Opening Dimensions STANDARD INSTALLATION PRO 48 24" (610) OPENING DEPTH INTEGRATED TOP VIEW 83 3/4" W (2127) OPENING HEIGHT OPENING WIDTH WINE SIDE VIEW FRONT VIEW NOTE: Shaded line represents profile of unit. OPENING WIDTH MODEL UNDERCOUNTER BI-36R, BI-36RG, BI-36F BI-30U, BI-30UG BI-36U, BI-36UG, BI-36UFD, BI-36S BI-42UFD, BI-42S, BI-42SID, BI-42SD BI-48S, BI-48SID, BI-48SD 12 | Sub-Zero Customer Care 800.222.7820 W 35 1/2" (902) 29 1/2" (749) 35 1/2" (902) 41 1/2" (1054) 47 1/2" (1206) If an 83" (2108) grille height is specified, the opening height must be decreased by 7/8" (22). If an 88" (2235) grille height is specified, the opening height must be increased by 4" (102). If two units are installed side by side, refer to page 14 for dual standard installations. BUILT-IN REFRIGERATION BUILT-IN Opening Dimensions FLUSH INSET INSTALLATION 26 3/16" (665) FLUSH INSET DEPTH 2 3/16" (56) PRO 48 FINISHED CLEATS* TOP VIEW 11/4" 1/4" (6) (32) W FLUSH INSET WIDTH INTEGRATED 84" (2134) FLUSH INSET HEIGHT 11/4" (32) 4" (102) 3" (76)* TYPICAL SIDE VIEW 2 3/16" (56) FRONT VIEW WINE *3" (76) typical depth. Shaded areas will be visible and should be finished to match cabinetry. NOTE: Shaded line represents profile of unit with 3/4" (19) panel. Dimensions assume a 3/4" (19) panel thickness. FLUSH INSET WIDTH MODEL BI-36R, BI-36RG, BI-36F BI-30U, BI-30UG BI-36U, BI-36UG, BI-36UFD, BI-36S BI-42UFD, BI-42S, BI-42SID, BI-42SD BI-48S, BI-48SID, BI-48SD W 38" (965) 32" (813) 38" (965) 44" (1118) 50" (1270) If an 83" (2108) grille height is specified, the flush inset height must be decreased by 7/8" (22). If an 88" (2235) grille height is specified, the flush inset height must be increased by 4" (102). subzero.com/specs | UNDERCOUNTER If two units are installed side by side, refer to page 15 for dual flush inset installations. 13 BUILT-IN BUILT-IN REFRIGERATION Opening Dimensions DUAL STANDARD INSTALLATION PRO 48 24" (610) OPENING DEPTH INTEGRATED TOP VIEW 83 3/4" W (2127) OPENING HEIGHT OPENING WIDTH WINE SIDE VIEW FRONT VIEW NOTE: Shaded line represents profile of unit. A dual installation kit will be required for this installation. OPENING WIDTH MODELS UNDERCOUNTER Two 30" Models 30" Model and 36" Model Two 36" Models 14 | Sub-Zero Customer Care 800.222.7820 W 59 3/4" (1518) 65 3/4" (1670) 71 3/4" (1822) BUILT-IN REFRIGERATION BUILT-IN Opening Dimensions DUAL FLUSH INSET INSTALLATION 26 3/16" (665) FLUSH INSET DEPTH 2 3/16" (56) PRO 48 FINISHED CLEATS* TOP VIEW 11/4" 1/4" (6) (32) W FLUSH INSET WIDTH INTEGRATED 84" (2134) FLUSH INSET HEIGHT 11/4" (32) 4" (102) 3" (76)* TYPICAL SIDE VIEW 2 3/16" (56) FRONT VIEW WINE *3" (76) typical depth. Shaded areas will be visible and should be finished to match cabinetry. NOTE: Shaded line represents profile of unit with 3/4" (19) panel. FLUSH INSET WIDTH MODELS Two 30" Models 30" Model and 36" Model Two 36" Models W Dimensions assume a 3/4" (19) panel thickness. A dual installation kit will be required for this installation. 62 1/4" (1581) 68 1/4" (1734) 74 1/4" (1886) UNDERCOUNTER subzero.com/specs | 15 BUILT-IN BUILT-IN REFRIGERATION Electrical Plumbing The electrical supply should be located within the shaded area shown in the illustration below. A separate circuit, servicing only this appliance is required. A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation. The water supply line should be located within the shaded area shown in the illustration below. The water supply line should be connected to the house supply with an easily accessible shut-off valve. Do not use self-piercing valves. The water supply line must not interfere with installation of the anti-tip brackets. PRO 48 Installation must comply with all applicable electrical codes. ELECTRICAL REQUIREMENTS Electrical Supply 115 VAC, 60 Hz Service 15 amp Receptacle 3-prong grounding-type A reverse osmosis system can be used provided there is constant water pressure of 35–120 psi (2.4–8.3 bar) supplied to the unit at all times. A copper line is not recommended for this application. Installation must comply with all applicable plumbing codes. PLUMBING REQUIREMENTS 1/4" OD copper, braided stainless steel or PEX tubing Water Supply Pressure 7" E INTEGRATED (178) 35–120 psi (2.4–8.3 bar) Excess Line for Connection 6" (152) 75 1/2" (1918) FROM FLOOR RIGHT SIDE OF OPENING RIGHT SIDE OF OPENING Electrical supply location. 18" (457) 6" (152) 3" (76) WINE AREA EXTENDS 1/2" (13) FORWARD ON FLOOR UNDERCOUNTER Water supply location. 16 | Sub-Zero Customer Care 800.222.7820 36" (914) BUILT-IN REFRIGERATION BUILT-IN Custom Panels For framed, overlay and flush inset applications, custom door panels must be provided. Handle hardware must also be provided for overlay and flush inset applications. Refer to panel requirements below and the charts on pages 20–25 for custom panel dimensions for your specific design application. Finish all sides of the custom panels. They may be visible when the door is open or through the window of glass door models. PANEL REQUIREMENTS PANEL WEIGHT BI-36R, BI-36RG, BI-36F All Other Models Grille Panel PANEL THICKNESS 75 lb (34 kg) 50 lb (23 kg) 13 lb (6 kg) MIN 1/4" 5/8" (6) (16) If the custom panel is thinner than 1/4" (6), a filler material must be added to achieve a proper fit. If the panel is thicker than 1/4" (6), rout an edge around the panel or mount the custom panel on a sheet of 1/4" (6) thick material and insert into the channel. Refer to the illustrations below. Routing, recessing or optional extended handles may be required for finger clearance. Refer to the full-scale template on page 32. When installing two units side by side, refer to page 14 for dual standard installations. 1/4" (6) TRIM REVEAL 1/4" (6) min INTEGRATED Framed Overlay and Flush Inset MAX The framed application is an overlay model with framed design features. It is not a separate model. PRO 48 IMPORTANT NOTE: Do not cover a glass door with a solid panel. FRAMED PANELS ROUT TO 1/4" (6) 1/4" (6) PANEL DOOR Panel 1/4" thick or less. DOOR Panel thicker than 1/4". WINE UNDERCOUNTER subzero.com/specs | 17 BUILT-IN BUILT-IN REFRIGERATION PRO 48 Custom Panels PARTIAL FRAMED OPTION PANEL MOUNTING KIT The partial framed kit includes a stainless steel panel for above and below the external dispenser. Refer to the chart below for panel width. The kit is available through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. A Sub-Zero custom panel mounting kit eliminates the need for a backer and spacer panel and is available through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. The kit consists of mounting cleats, screws and gages used to properly position the cleats. The kit is available for all built-in models except glass door models. Dual installations require two mounting kits. PARTIAL FRAMED PANEL MODEL BI-42SD BI-48SD WIDTH 15 1/16" (383) 18 3/4" (476) OVERLAY PANELS Overlay panels are typically created by combining a 3/4" (19) custom panel, a .10" (3) spacer panel and a 1/4" (6) backer panel. Refer to the illustrations below. INTEGRATED When installing two units side by side, refer to page 14 for dual standard installations. CUSTOM PANEL SPACER PANEL SPACER PANEL CUSTOM PANEL BACKER PANEL BACKER PANEL TRIM 5/16" (8) min 3/4" 1/8" (3) (OVERLAY) (19) typical UNDERCOUNTER WINE Panel assembly cross section (overlay). 18 | Sub-Zero Customer Care 800.222.7820 .10" (3) 1/4" (6) Panel assembly rear view. BUILT-IN REFRIGERATION BUILT-IN Custom Panels FLUSH INSET PANELS ICE AND WATER DISPENSER The flush inset application is an overlay model with flush inset panels. It is not a separate model. For models BI-42SD and BI-48SD, the refrigerator door panel must include a cut-out to accommodate the external dispenser. The thickness of the panel in this area can range from 1/4" (6) to a maximum of 1 1/8" (29). Refer to the illustrations below. For flush inset panels thicker than 3/4" (19), a 90° door stop may be required to prevent interference with adjacent cabinets. Refer to the full-scale templates at the end of this guide. PRO 48 The flush inset design allows custom panels to be installed flush with adjacent cabinets. Similar to overlay, flush inset panels are typically created by combining a 3/4" (19) custom panel, a .10" (3) spacer panel and a 1/4" (6) backer panel. Refer to the illustrations for overlay panels. 5 /8 " 3/32" (16) (2) When installing two units side by side, refer to page 15 for dual flush inset installations. 6 5/16" (160) 1/8" (3) RADIUS 2" (51) HANDLE 1" 12 7/8" (25) (327) Dispenser dimensions. INTEGRATED GLASSWELL Handle placement. WINE UNDERCOUNTER subzero.com/specs | 19 BUILT-IN BUILT-IN REFRIGERATION Framed Panel Dimensions H H H A A A H H A PRO 48 H H H H H A A W A H W H H B W BI-36R / BI-36F W W BI-36RG BI-30U / BI-36U INTEGRATED MODEL BI-36R, BI-36RG, BI-36F REFRIGERATOR / FREEZER Door Panel GRILLE (OPTIONAL) Grille Panel BI-36RG Stiles / Rails W BI-30UG / BI-36UG W BI-36UFD / BI-42UFD MODEL BI-36U, BI-36UG W H 35 3/4" (908) 69 9/16" (1767) W H 35 3/4" (908) 8 15/16" (227) A B 5 3/16" (132) 10 5/16" (262) REFRIGERATOR Door Panel FREEZER Drawer Panel GRILLE (OPTIONAL) Grille Panel W H 35 3/4" (908) 49 15/16" (1268) W H 35 3/4" (908) 18 11/16" (475) W H 35 3/4" (908) 8 15/16" (227) BI-36UG REFRIGERATOR Door Panel FREEZER Drawer Panel WINE GRILLE (OPTIONAL) Grille Panel A 5 3/16" (132) Stiles / Rails MODEL BI-30U, BI-30UG W H 29 3/4" (756) 49 15/16" (1268) W H 29 3/4" (756) 18 11/16" (475) W H 29 3/4" (756) 8 15/16" (227) BI-30UG Stiles / Rails A 5 3/16" (132) MODEL BI-36UFD REFRIGERATOR (2 PANELS) Door Panels FREEZER Drawer Panel GRILLE (OPTIONAL) Grille Panel W H 17 5/8" (448) 49 15/16" (1268) W H 35 3/4" (908) 18 11/16" (475) W H 35 3/4" (908) 8 15/16" (227) MODEL BI-42UFD REFRIGERATOR (2 PANELS) Door Panels FREEZER Drawer Panel UNDERCOUNTER GRILLE (OPTIONAL) Grille Panel 20 | Sub-Zero Customer Care 800.222.7820 W H 20 5/8" (524) 49 15/16" (1268) W H 41 3/4" (1060) 18 11/16" (475) W H 41 3/4" (1060) 8 15/16" (227) BUILT-IN REFRIGERATION BUILT-IN Framed Panel Dimensions H H H H PRO 48 A B W W BI-36S / BI-42S / BI-42SID BI-48S / BI-48SID W W BI-42SD / BI-48SD MODEL BI-36S MODEL BI-48S, BI-48SID, BI-48SD Door Panel W H 19 13/16" (503) 69 9/16" (1767) FREEZER Door Panel W H 15 7/16" (392) 69 9/16" (1767) GRILLE (OPTIONAL) Grille Panel W H 35 3/4" (908) 8 15/16" (227) REFRIGERATOR Door Panel FREEZER Door Panel GRILLE (OPTIONAL) Grille Panel BI-48SD Dispenser Cut-Out* MODEL BI-42S, BI-42SID, BI-42SD REFRIGERATOR Door Panel FREEZER Door Panel GRILLE (OPTIONAL) BI-42SD Dispenser Cut-Out* Cut-Out Location H 24 13/16" (630) 69 9/16" (1767) W H 16 7/16" (418) 69 9/16" (1767) W H 41 3/4" (1060) 8 15/16" (227) W H 5 7/8" (149) 12 7/16" (316) A B 1 7/8" (48) 28 3/4" (730) Cut-Out Location H 69 9/16" (1767) W H 18 3/4" (476) 69 9/16" (1767) W H 47 3/4" (1213) 8 15/16" (227) W H 5 7/8" (149) 12 7/16" (316) A B 1 7/8" (48) 28 3/4" (730) *For models BI-42SD and BI-48SD, panel thickness in the dispenser area can range from 1/4" (6) to a maximum of 1 1/8" (29). If the panel is thicker, you must rout out a minimum 1/4" (6) flat landing area to accommodate the dispenser. WINE Grille Panel W W 28 1/2" (724) INTEGRATED REFRIGERATOR UNDERCOUNTER subzero.com/specs | 21 BUILT-IN BUILT-IN REFRIGERATION Overlay Panel Dimensions H H H A A A H H A PRO 48 H H H H H A A W A H W H H B W BI-36R / BI-36F W W BI-36RG BI-30U / BI-36U INTEGRATED MODEL BI-36R, BI-36RG, BI-36F REFRIGERATOR / FREEZER Overlay Panel Spacer Panel Backer Panel GRILLE Overlay Panel Spacer Panel Backer Panel BI-36RG Stiles / Rails W BI-30UG / BI-36UG W BI-36UFD / BI-42UFD MODEL BI-36U, BI-36UG W H 36" (914) 35 1/8" (892) 35 3/4" (908) 69 3/4" (1772) 68 15/16" (1751) 69 9/16" (1767) W H 36" (914) 35 1/8" (892) 35 3/4" (908) 9 1/4" (235)* 8 5/16" (211) 8 15/16" (227) A B 5 1/4" (133) 10 3/8" (264) REFRIGERATOR Overlay Panel Spacer Panel Backer Panel FREEZER Overlay Panel Spacer Panel Backer Panel GRILLE Overlay Panel Spacer Panel Backer Panel W H 36" (914) 35 1/8" (892) 35 3/4" (908) 50 1/8" (1273) 49 5/16" (1253) 49 15/16" (1268) W H 36" (914) 35 1/8" (892) 35 3/4" (908) 19" (483) 18 1/16" (459) 18 11/16" (475) W H 36" (914) 35 1/8" (892) 35 3/4" (908) 9 1/4" (235)* 8 5/16" (211) 8 15/16" (227) MODEL BI-30U, BI-30UG WINE REFRIGERATOR Overlay Panel Spacer Panel Backer Panel FREEZER Overlay Panel Spacer Panel Backer Panel GRILLE Overlay Panel Spacer Panel Backer Panel W 30" (762) 29 1/8" (740) 29 3/4" (756) 49 5/16" (1253) 49 15/16" (1268) W H 30" (762) 29 1/8" (740) 29 3/4" (756) 19" (483) 18 1/16" (459) 18 11/16" (475) W H 9 1/4" (235)* 8 5/16" (211) 8 15/16" (227) UNDERCOUNTER Stiles / Rails | (1273) 30" (762) 29 1/8" (740) 29 3/4" (756) BI-30UG 22 H 50 1/8" Sub-Zero Customer Care 800.222.7820 A 5 1/4" (133) BI-36UG A 5 1/4" (133) Stiles / Rails MODEL BI-36UFD REFRIGERATOR (2 PANELS) Overlay Panels Spacer Panels Backer Panels FREEZER Overlay Panel Spacer Panel Backer Panel GRILLE Overlay Panel Spacer Panel Backer Panel W H 17 7/8" (454) 17" (432) 17 5/8" (448) 50 1/8" (1273) 49 5/16" (1253) 49 15/16" (1268) W H 36" (914) 35 1/8" (892) 35 3/4" (908) 19" (483) 18 1/16" (459) 18 11/16" (475) W H 36" (914) 35 1/8" (892) 35 3/4" (908) 9 1/4" (235)* 8 5/16" (211) 8 15/16" (227) BUILT-IN REFRIGERATION BUILT-IN Overlay Panel Dimensions H MODEL BI-42S, BI-42SID, BI-42SD H REFRIGERATOR Overlay Panel Spacer Panel Backer Panel H H BI-36S / BI-42S / BI-42SID BI-48S / BI-48SID W W H 16 11/16" (424) 15 13/16" (402) 16 7/16" (418) 69 3/4" (1772) 68 15/16" (1751) 69 9/16" (1767) GRILLE Overlay Panel Spacer Panel Backer Panel W W H 42" (1067) 41 1/8" (1045) 41 3/4" (1060) 9 1/4" (235)* 8 5/16" (211) 8 15/16" (227) BI-42SD BI-42SD / BI-48SD Dispenser Cut-Out Cut-Out Location MODEL BI-42UFD Overlay Panels Spacer Panels Backer Panels FREEZER Overlay Panel Spacer Panel Backer Panel GRILLE Overlay Panel Spacer Panel Backer Panel H 20 7/8" (530) 20" (508) 20 5/8" (524) 50 1/8" (1273) 49 5/16" (1253) 49 15/16" (1268) W H 42" (1067) 41 1/8" (1045) 41 3/4" (1060) 19" (483) 18 1/16" (459) 18 11/16" (475) W H 42" (1067) 41 1/8" (1045) 41 3/4" (1060) 9 1/4" (235)* 8 5/16" (211) 8 15/16" (227) REFRIGERATOR Overlay Panel Spacer Panel Backer Panel FREEZER Overlay Panel Spacer Panel Backer Panel GRILLE Overlay Panel Spacer Panel Backer Panel BI-48SD FREEZER Overlay Panel Spacer Panel Backer Panel GRILLE Dispenser Cut-Out W H 20 1/16" (510) 19 3/16" (487) 19 13/16" (503) 69 3/4" (1772) 68 15/16" (1751) 69 9/16" (1767) W H 15 11/16" (398) 14 13/16" (376) 15 7/16" (392) 69 3/4" (1772) 68 15/16" (1751) 69 9/16" (1767) W H 36" (914) 35 1/8" (892) 35 3/4" (908) 9 1/4" (235)* 8 5/16" (211) 8 15/16" (227) Cut-Out Location W H 28 3/4" (730) 27 7/8" (708) 28 1/2" (724) 69 3/4" (1772) 68 15/16" (1751) 69 9/16" (1767) W H 19" (483) 18 1/8" (460) 18 3/4" (476) 69 3/4" (1772) 68 15/16" (1751) 69 9/16" (1767) W H 48" (1219) 47 1/8" (1197) 47 3/4" (1213) 9 1/4" (235)* 8 5/16" (211) 8 15/16" (227) W H 5 7/8" (149) 12 7/16" (316) A B 2" (51) 28 13/16" (732) *Panel height may be increased by 7/16" (11) to hide upper main frame. For more information, refer to the built-in panel configurator at subzero.com/trade/panels. Grille panel dimensions are for standard 84" (2134) overall unit height. For 83" (2108) height, subtract 1" (25) from grille panel height dimensions and for 88" (2235) height, add 4" (102). A specific panel grille must be ordered for an 83" or 88" overall unit height. UNDERCOUNTER Overlay Panel Spacer Panel Backer Panel B 28 13/16" (732) WINE Overlay Panel Spacer Panel Backer Panel A 2" (51) MODEL BI-48S, BI-48SID, BI-48SD W MODEL BI-36S REFRIGERATOR H 12 7/16" (316) INTEGRATED REFRIGERATOR (2 PANELS) W 5 7/8" (149) PRO 48 Overlay Panel Spacer Panel Backer Panel B W H 69 3/4" (1772) 68 15/16" (1751) 69 9/16" (1767) FREEZER A W W 25 1/16" (637) 24 3/16" (614) 24 13/16" (630) subzero.com/specs | 23 BUILT-IN BUILT-IN REFRIGERATION Flush Inset Panel Dimensions H H H A A A H A H PRO 48 H H H H H B A W B H W H H B W W BI-36R / BI-36F W BI-36RG BI-30U / BI-36U INTEGRATED MODEL BI-36R, BI-36RG, BI-36F REFRIGERATOR / FREEZER Flush Inset Panel Spacer Panel Backer Panel GRILLE Flush Inset Panel Spacer Panel Backer Panel BI-36RG Stiles / Rails W BI-30UG / BI-36UG W BI-36UFD / BI-42UFD MODEL BI-36U, BI-36UG W H 37" (940) 35 1/8" (892) 35 3/4" (908) 69 3/4" (1772) 68 15/16" (1751) 69 9/16" (1767) W H 37" (940) 35 1/8" (892) 35 3/4" (908) 9 1/4" (235) 8 5/16" (211) 8 15/16" (227) A B 5 3/4" (146) 10 3/8" (264) REFRIGERATOR Flush Inset Panel Spacer Panel Backer Panel FREEZER Flush Inset Panel Spacer Panel Backer Panel GRILLE Flush Inset Panel Spacer Panel Backer Panel W H 37" (940) 35 1/8" (892) 35 3/4" (908) 50 1/8" (1273) 49 5/16" (1253) 49 15/16" (1268) W H 37" (940) 35 1/8" (892) 35 3/4" (908) 19" (483) 18 1/16" (459) 18 11/16" (475) W H 37" (940) 35 1/8" (892) 35 3/4" (908) 9 1/4" (235) 8 5/16" (211) 8 15/16" (227) MODEL BI-30U, BI-30UG WINE REFRIGERATOR Flush Inset Panel Spacer Panel Backer Panel FREEZER Flush Inset Panel Spacer Panel Backer Panel GRILLE Flush Inset Panel Spacer Panel Backer Panel UNDERCOUNTER BI-30UG Stiles / Rails 24 | W H 50 1/8" 31" (787) 29 1/8" (740) 29 3/4" (756) 49 5/16" (1253) 49 15/16" (1268) W H 31" (787) 29 1/8" (740) 29 3/4" (756) 19" (483) 18 1/16" (459) 18 11/16" (475) (1273) W H 31" (787) 29 1/8" (740) 29 3/4" (756) 9 1/4" (235) 8 5/16" (211) 8 15/16" (227) A B 5 3/4" (146) 5 1/4" (133) Sub-Zero Customer Care 800.222.7820 BI-36UG Stiles / Rails A B 5 3/4" (146) 5 1/4" (133) MODEL BI-36UFD REFRIGERATOR (2 PANELS) Flush Inset Panels Spacer Panels Backer Panels FREEZER Flush Inset Panel Spacer Panel Backer Panel GRILLE Flush Inset Panel Spacer Panel Backer Panel W H 18 3/8" (467) 17" (432) 17 5/8" (448) 50 1/8" (1273) 49 5/16" (1253) 49 15/16" (1268) W H 37" (940) 35 1/8" (892) 35 3/4" (908) 19" (483) 18 1/16" (459) 18 11/16" (475) W H 37" (940) 35 1/8" (892) 35 3/4" (908) 9 1/4" (235) 8 5/16" (211) 8 15/16" (227) BUILT-IN REFRIGERATION BUILT-IN Flush Inset Panel Dimensions H MODEL BI-42S, BI-42SID, BI-42SD H REFRIGERATOR Flush Inset Panel Spacer Panel Backer Panel H H BI-36S / BI-42S / BI-42SID BI-48S / BI-48SID W W H 17 3/16" (437) 15 13/16" (402) 16 7/16" (418) 69 3/4" (1772) 68 15/16" (1751) 69 9/16" (1767) GRILLE Flush Inset Panel Spacer Panel Backer Panel W W H 43" (1092) 41 1/8" (1045) 41 3/4" (1060) 9 1/4" (235) 8 5/16" (211) 8 15/16" (227) DISPENSER (BI-42SD) BI-42SD / BI-48SD Dispenser Cut-Out Cut-Out Location MODEL BI-42UFD Flush Inset Panels Spacer Panels Backer Panels FREEZER Flush Inset Panel Spacer Panel Backer Panel GRILLE Flush Inset Panel Spacer Panel Backer Panel H 21 3/8" (543) 20" (508) 20 5/8" (524) 50 1/8" (1273) 49 5/16" (1253) 49 15/16" (1268) W H 43" (1092) 41 1/8" (1045) 41 3/4" (1060) 19" (483) 18 1/16" (459) 18 11/16" (475) W H 43" (1092) 41 1/8" (1045) 41 3/4" (1060) 9 1/4" (235) 8 5/16" (211) 8 15/16" (227) REFRIGERATOR Flush Inset Panel Spacer Panel Backer Panel FREEZER Flush Inset Panel Spacer Panel Backer Panel GRILLE Flush Inset Panel Spacer Panel Backer Panel DISPENSER (BI-48SD) FREEZER Flush Inset Panel Spacer Panel Backer Panel GRILLE Cut-Out W H 20 9/16" (522) 19 3/16" (487) 19 13/16" (503) 69 3/4" (1772) 68 15/16" (1751) 69 9/16" (1767) W H 16 3/16" (411) 14 13/16" (376) 15 7/16" (392) 69 3/4" (1772) 68 15/16" (1751) 69 9/16" (1767) W H 37" (940) 35 1/8" (892) 35 3/4" (908) 9 1/4" (235) 8 5/16" (211) 8 15/16" (227) Cut-Out Location W H 29 1/4" (743) 27 7/8" (708) 28 1/2" (724) 69 3/4" (1772) 68 15/16" (1751) 69 9/16" (1767) W H 19 1/2" (495) 18 1/8" (460) 18 3/4" (476) 69 3/4" (1772) 68 15/16" (1751) 69 9/16" (1767) W H 49" (1245) 47 1/8" (1197) 47 3/4" (1213) 9 1/4" (235) 8 5/16" (211) 8 15/16" (227) W H 5 7/8" (149) 12 7/16" (316) A B 2" (51) 28 13/16" (732) Grille panel dimensions are for standard 84" (2134) overall unit height. For 83" (2108) height, subtract 1" (25) from grille panel height dimensions and for 88" (2235) height, add 4" (102). A specific panel grille must be ordered for an 83" or 88" overall unit height. UNDERCOUNTER Flush Inset Panel Spacer Panel Backer Panel B 28 13/16" (732) WINE Flush Inset Panel Spacer Panel Backer Panel A 2" (51) MODEL BI-48S, BI-48SID, BI-48SD W MODEL BI-36S REFRIGERATOR H 12 7/16" (316) INTEGRATED REFRIGERATOR (2 PANELS) W 5 7/8" (149) PRO 48 Flush Inset Panel Spacer Panel Backer Panel B W H 69 3/4" (1772) 68 15/16" (1751) 69 9/16" (1767) FREEZER A W W 25 9/16" (649) 24 3/16" (614) 24 13/16" (630) subzero.com/specs | 25 BUILT-IN BUILT-IN REFRIGERATION Flush Inset Panels PANEL OFFSETS TOP VIEW TOP VIEW The illustrations provide panel offsets and reveals for built-in models in a flush inset application. Refer to the chart below for reference to the illustrations. DOOR / DRAWER / GRILLE DOOR BACKER SPACER DOOR CABINETRY PRO 48 PANEL OFFSET ALL REFRIGERATOR / ALL FREEZER Door / Grille Sides Grille Top Grille Bottom / Door Top Door Bottom OVER-AND-UNDER Door / Drawer / Grille Sides Grille Top Grille Bottom / Door Top Door Bottom / Drawer Top Drawer Bottom INTEGRATED SIDE-BY-SIDE Doors (hinge) / Grille Sides Doors (handle) Sides Grille Top Grille Bottom / Door Top Door Bottom ILLUS FLUSH INSET PANEL A C D F ILLUS A C D E F 5/16" (8) 1/2" (13) 5/16" (8) 1/8" (3) 5/8" (16) 1/4" (6) REVEAL Illus. A Illus. B CABINETRY 1/2" (13) 5/16" (8) 5/32" (4) GRILLE ILLUS A B C D F GRILLE 1/8" 5/16" (3) (8) 1/2" (13) DOOR 3/32" 5/16" (2) (8) SIDE VIEW SIDE VIEW Illus. C Illus. D DOOR / DRAWER 5/16" (8) 3/32" (2) DOOR WINE 5/8" (16) DRAWER 5/16" (8) 5/32" 5/16" (4) (8) SIDE VIEW UNDERCOUNTER Illus. E 26 | Sub-Zero Customer Care 800.222.7820 SIDE VIEW Illus. F 3/32" (2) BUILT-IN REFRIGERATION BUILT-IN Dual Installation For dual standard installations, panel dimensions are the same as for single installations. Refer to the charts on pages 20–23. Panel dimensions and offsets for dual flush inset installations are listed on the following pages. PRO 48 If two units are installed side by side, a dual installation kit may be required. Installations without a custom filler strip require a dual installation kit. If a dual installation kit is not specified, a 2" (51) filler strip is recommended between units. A custom filler strip is required when installing two French door or side-by-side models. Dual installations without a filler strip can only be accomplished using two units with opposite hinges. Refer to the illustrations below. Dual installation kits are available through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. For questions regarding the installation, call Sub-Zero customer care at 800-222-7820. INTEGRATED WITHOUT FILLER STRIP Opposite hinges. FILLER STRIP Same side hinges. WINE UNDERCOUNTER subzero.com/specs | 27 BUILT-IN BUILT-IN REFRIGERATION Dual Flush Inset Panel Dimensions H H H H A A A H H PRO 48 H B A A H B H H B W W BI-36R / BI-36F W BI-36RG BI-30U / BI-36U INTEGRATED MODEL BI-36R, BI-36RG, BI-36F W H 36 1/2" (927) 35 1/8" (892) 35 3/4" (908) 69 3/4" (1772) 68 15/16" (1751) 69 9/16" (1767) GRILLE Flush Inset Panel Spacer Panel Backer Panel W H 36 1/2" (927) 35 1/8" (892) 35 3/4" (908) 9 1/4" (235) 8 5/16" (211) 8 15/16" (227) BI-36RG Stiles / Rails BI-30UG / BI-36UG MODEL BI-36U, BI-36UG REFRIGERATOR / FREEZER Flush Inset Panel Spacer Panel Backer Panel W A B 5 3/4" (146) 10 3/8" (264) REFRIGERATOR Flush Inset Panel Spacer Panel Backer Panel FREEZER Flush Inset Panel Spacer Panel Backer Panel GRILLE Flush Inset Panel Spacer Panel Backer Panel W H 36 1/2" (927) 35 1/8" (892) 35 3/4" (908) 50 1/8" (1273) 49 5/16" (1253) 49 15/16" (1268) W H 36 1/2" (927) 35 1/8" (892) 35 3/4" (908) 19" (483) 18 1/16" (459) 18 11/16" (475) W H 36 1/2" (927) 35 1/8" (892) 35 3/4" (908) 9 1/4" (235) 8 5/16" (211) 8 15/16" (227) MODEL BI-30U, BI-30UG WINE REFRIGERATOR Flush Inset Panel Spacer Panel Backer Panel FREEZER Flush Inset Panel Spacer Panel Backer Panel GRILLE Flush Inset Panel Spacer Panel Backer Panel UNDERCOUNTER BI-30UG Stiles / Rails 28 | W 30 1/2" (775) 29 1/8" (740) 29 3/4" (756) H 50 1/8" (1273) 49 5/16" (1253) 49 15/16" (1268) W H 30 1/2" (775) 29 1/8" (740) 29 3/4" (756) 19" (483) 18 1/16" (459) 18 11/16" (475) W H 30 1/2" (775) 29 1/8" (740) 29 3/4" (756) 9 1/4" (235) 8 5/16" (211) 8 15/16" (227) A B 5 3/4" (146) 5 1/4" (133) Sub-Zero Customer Care 800.222.7820 BI-36UG Stiles / Rails A B 5 3/4" (146) 5 1/4" (133) Grille panel dimensions are for standard 84" (2134) overall unit height. For 83" (2108) height, subtract 1" (25) from grille panel height dimensions and for 88" (2235) height, add 4" (102). A specific panel grille must be ordered for an 83" or 88" overall unit height. For dual wide grilles, refer to page 30. BUILT-IN REFRIGERATION BUILT-IN Dual Installation DUAL FLUSH INSET PANEL OFFSETS TOP VIEW The illustrations provide panel offsets and reveals for built-in models in a dual flush inset application. Refer to the chart below for reference to the illustrations. TOP VIEW DOOR / DRAWER / GRILLE DUAL TRIM BACKER SPACER CABINETRY DOOR DOOR PANEL OFFSET Door (hinge) / Grille Sides Door (handle) Sides Grille Top Grille Bottom / Door Top Door Bottom OVER-AND-UNDER Door (hinge) / Drawer / Grille Sides Door (handle) Sides Grille Top Grille Bottom / Door Top Door Bottom / Drawer Top Drawer Bottom ILLUS FLUSH INSET PANEL A B C D F ILLUS 5/16" (8) 1/2" (13) 5/16" (8) 1/8" (3) 5/8" (16) 1/4" (6) REVEAL Illus. A A B C D E F PRO 48 ALL REFRIGERATOR / ALL FREEZER Illus. B CABINETRY 1/2" (13) 1/8" 5/16" (3) (8) 1/2" (13) DOOR 3/32" 5/16" (2) (8) SIDE VIEW SIDE VIEW Illus. C INTEGRATED GRILLE 5/16" (8) 5/32" (4) GRILLE Illus. D DOOR / DRAWER 5/16" (8) 3/32" (2) DOOR DRAWER 5/16" (8) 5/32" 5/16" (4) (8) SIDE VIEW Illus. E WINE 5/8" (16) SIDE VIEW 3/32" (2) Illus. F UNDERCOUNTER subzero.com/specs | 29 BUILT-IN BUILT-IN REFRIGERATION Dual Installation DUAL WIDE GRILLE DUAL WIDE GRILLE—FLUSH INSET A dual wide grille spans the entire width of both units in a dual installation and is a part of a dual installation kit. TWO 30" MODELS W H Flush Inset Panel Spacer Panel Backer Panel 61 1/4" (1556) 59 3/8" (1508) 60" (1524) 9 1/4" (235) 8 5/16" (211) 8 15/16" (227) PRO 48 For overlay and flush inset panel dimensions for the dual wide grille, refer to the charts below. Dimensions listed are for a standard 84" (2134) finished height. DUAL WIDE GRILLE—OVERLAY TWO 30" MODELS Overlay Panel Spacer Panel Backer Panel 30" MODEL AND 36" MODEL Overlay Panel Spacer Panel Backer Panel Overlay Panel Spacer Panel Backer Panel | W H 67 1/4" (1708) 65 3/8" (1661) 66" (1676) 9 1/4" (235) 8 5/16" (211) 8 15/16" (227) W H TWO 36" MODELS W H 9 1/4" (235) 8 5/16" (211) 8 15/16" (227) Flush Inset Panel Spacer Panel Backer Panel 73 1/4" (1861) 71 3/8" (1813) 72" (1829) 9 1/4" (235) 8 5/16" (211) 8 15/16" (227) W H 66 1/4" (1683) 65 3/8" (1661) 66" (1676) 9 1/4" (235) 8 5/16" (211) 8 15/16" (227) W H 72 1/4" (1835) 71 3/8" (1813) 72" (1829) 9 1/4" (235) 8 5/16" (211) 8 15/16" (227) UNDERCOUNTER 30 Flush Inset Panel Spacer Panel Backer Panel 60 1/4" (1530) 59 3/8" (1508) 60" (1524) WINE INTEGRATED TWO 36" MODELS 30" MODEL AND 36" MODEL Sub-Zero Customer Care 800.222.7820 BUILT-IN REFRIGERATION BUILT-IN Handle Hardware The custom side panels must be a minimum of 24" (610) deep and 1/2" (13) thick. Routing will be necessary for the side panel to fit flush against the side of the unit. Refer to the illustrations below. Optional stainless steel tubular and pro handles are available through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. When installing a built-in unit with a custom side panel, an accessory kit is required. Stainless steel and white enamel side panels are available through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. Refer to the chart below for the length and stud spacing of standard handles for built-in models. STANDARD HANDLES FULL DOOR Tubular Pro OVER-AND-UNDER DOOR 24" (610) Tubular Pro FRONT OF SIDE PANEL 30" DRAWER 1" (25) 1 7/8" (48) Tubular Pro 36" DRAWER 1/8" (3) 1/2" (13) ROUT TO 1/8" (3) 1 7/8"(48) 84" 1" (25) MAIN FRAME 42" DRAWER SIDE PANEL ROUTING Tubular Pro STUD SPACING 43 7/8" (1114) 43 7/8" (1114) LENGTH STUD SPACING 44 1/4" (1124) 37 1/2" (952) 36 1/4" (921) 36 1/4" (921) LENGTH STUD SPACING 24 5/16" (633) 17 9/16" (447) 16 5/16" (414) 16 5/16" (414) LENGTH STUD SPACING 30 5/16" (770) 23 5/8" (600) 22 5/16" (567) 22 5/16" (567) LENGTH STUD SPACING 36 5/16" (922) 29 5/8" (753) 28 5/16" (719) 28 5/16" (719) INTEGRATED Tubular Pro LENGTH 63 7/8" (1622) 45 3/16" (1147) PRO 48 Side Panel (2134) Routing detail. 4 1/4" (108) ROUT TO 3/16" (5) (OVER-AND-UNDER MODELS) 5 3/4" (146) 20 1/2" (521) WINE 4" (102) OPTIONAL TOE KICK CUT-OUT 2 5/8" (67) Side panel dimensions. UNDERCOUNTER subzero.com/specs | 31 BUILT-IN BUILT-IN REFRIGERATION Framed Panels PRO 48 FULL-SCALE TEMPLATE OPTIONAL EXTENDED FULL-LENGTH HANDLE INTEGRATED STANDARD FULL-LENGTH HANDLE 1" 2" 3" (25) (51) (76) 11/4" (32) PANEL 1" (25) PANEL 3/4" (19) PANEL 1/2" (13) PANEL WINE 1/4" (6) FRAMED PANEL DOOR UNDERCOUNTER Framed panel thickness. 32 | Sub-Zero Customer Care 800.222.7820 BUILT-IN REFRIGERATION BUILT-IN Overlay and Flush Inset Panels FULL-SCALE TEMPLATE Overlay and flush inset panels must be a minimum of 5/8" (16) thick to support mounting the handle. Panel thickness does not include backer and spacer panel. Mount handle close to the opening edge of the door. PRO 48 DEPTH OF TUBULAR AND PRO HANDLES 2" 3" (51) (76) INTEGRATED 1" (25) 11/4" (32) PANEL 1" (25) PANEL 3/4" (19) PANEL .10" (3) SPACER PANEL 1/4" (6) BACKER PANEL WINE DOOR Overlay and flush inset panel thickness. UNDERCOUNTER subzero.com/specs | 33 BUILT-IN BUILT-IN REFRIGERATION Overlay Application FULL-SCALE TEMPLATE 237/8" (606) TO REAR OF UNIT OVERALL WIDTH OF UNIT PRO 48 0" (0) 1/4" (6) 1/2" (13) 3/4" (19) 1" (25) 11/4" (32) 11/2" (38) 13/4" (44) INTEGRATED 2" (51) 21/4" (57) 21/2" (63) 23/4" (70) 3" (76) 31/4" (83) 31/2" (89) WINE 1" (25) THICK PANEL 3/4" (19) THICK OVERLAY PANEL (TYPICAL) 1/4" (6) BACKER UNDERCOUNTER PANEL 0" 1" (25) SCALE 90° door opening (top view). 34 | Sub-Zero Customer Care 800.222.7820 BUILT-IN REFRIGERATION BUILT-IN Flush Inset Application FULL-SCALE TEMPLATE 24" (610) TO BACK WALL For panels thicker than 3/4" (19), a 90° door stop may be required to prevent interference with adjacent cabinets. 1 1/4" (32) PRO 48 2 3/16" (56) ASSUMES 3/4" (19) FLUSH INSET PANEL THICKNESS INTEGRATED WINE 1" (25) THICK PANEL 3/4" (19) THICK FLUSH INSET PANEL (TYPICAL) 1/4" (6) BACKER PANEL 0" 1" (25) UNDERCOUNTER SCALE 110° door opening (top view). subzero.com/specs | 35 BUILT-IN BUILT-IN REFRIGERATION PRO 48 FILLER STRIP 11/4" (32) DOOR CLOSED WINE INTEGRATED APPROX PROFILE OF STAINLESS STEEL WRAPPED DOOR AND HANDLE Dual Standard Installation FULL-SCALE TEMPLATE Typical framed, overlay or stainless steel dual installation with filler strip at maximum 110° door opening. Panel thickness may require a 90° door stop. UNDERCOUNTER 0" 1" (25) SCALE Dual standard installation (top view). 36 | Sub-Zero Customer Care 800.222.7820 DOOR OPEN 110° BUILT-IN REFRIGERATION BUILT-IN FILLER STRIP PRO 48 1 1/2" (38) 1/2" (13) PROFILE OF 3/4" (19) FLUSH INSET PANEL AND TUBULAR HANDLE DOOR CLOSED INTEGRATED WINE Dual Flush Inset Installation DOOR OPEN 110° FULL-SCALE TEMPLATE Typical flush inset dual installation with filler strip at maximum 110° door opening. Panel thickness may require a 90° door stop. 0" 1" (25) UNDERCOUNTER SCALE Dual flush inset installation (top view). subzero.com/specs | 37 PRO 48 REFRIGERATION BUILT-IN PRO 48 Refrigeration Freshness finds unmistakable expression in the Sub-Zero PRO 48. An 800-pound monument to food preservation— equal parts sculpted metal design statement and culinary secret weapon. Its vast interior, like its bold exterior, is crafted of stainless steel. The PRO 48 is available with or without a glass door and may be either built in or freestanding. KEY FEATURES • Stainless steel interior as well as exterior. • Handles coordinate with handles of Wolf ranges. • Dual refrigeration system enhanced with triple evaporators allow independent control of storage conditions in refrigerator cabinet and drawer compartments. • Advanced water filtration system. • Slide-out stainless steel bins fit neatly under refrigerator glass shelves. • Exterior temperature display. • Flip-up grille provides easy access for quick routine maintenance. • Star-K certified. PRO 48 MODELS 648PRO INTEGRATED Can be used freestanding or installed as a standard or flush built-in application. PRO 48 • 648PROG WINE UNDERCOUNTER subzero.com/specs | 39 BUILT-IN PRO 48 REFRIGERATION Overall Dimensions PRO 48 MODELS 25 7/8" (657) PRO 48 48" (1219) 84" (2134) 42 1/8" (1070) 30 1/2" INTEGRATED (775) 4" (102) HEIGHT DIMENSIONS ± 1/2" (13) 30 3/16" (767) 23 7/8" (606) 14 1/2" (368) 21" (533) 30 3/4" WINE (781) SPECIFICATIONS INTERIOR CAPACITY R CU FT (L) F CU FT (L) 648PRO, 648PROG 18.4 (521) 11.7 (331) SHIPPING WEIGHT 2 3/8" (60) UNDERCOUNTER Models 648PRO and 648PROG. 40 | Sub-Zero Customer Care 800.222.7820 648PRO 648PROG LB (KG) 860 (390) 875 (397) PRO 48 REFRIGERATION BUILT-IN Opening Dimensions STANDARD AND FLUSH INSTALLATION D OPENING DEPTH PRO 48 TOP VIEW W OPENING WIDTH SIDE VIEW INTEGRATED H OPENING HEIGHT FRONT VIEW WINE OPENING DIMENSIONS INSTALLATION Standard Flush W H D 47 1/2" (1206) 48" (1219) 83 3/4" (2127) 84 1/8" (2137) 24" (610) 26" (660) For standard built-in installations, the face frame of the unit will extend 2" (51) beyond cabinetry. For flush installations, the front of the face frame will be flush with surrounding cabinetry. UNDERCOUNTER subzero.com/specs | 41 BUILT-IN PRO 48 REFRIGERATION Electrical Plumbing The electrical supply should be located within the shaded area shown in the illustration below. A separate circuit, servicing only this appliance is required. A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation. The water supply line should be located within the shaded area shown in the illustration below. The water supply line should be connected to the house supply with an easily accessible shut-off valve. Do not use self-piercing valves. The water supply line must not interfere with installation of the anti-tip bracket. PRO 48 Installation must comply with all applicable electrical codes. ELECTRICAL REQUIREMENTS Electrical Supply 115 VAC, 60 Hz Service 15 amp Receptacle 3-prong grounding-type A reverse osmosis system can be used provided there is constant water pressure of 35–120 psi (2.4–8.3 bar) supplied to the unit at all times. A copper line is not recommended for this application. Installation must comply with all applicable plumbing codes. PLUMBING REQUIREMENTS 1/4" OD copper, braided stainless steel or PEX tubing Water Supply Pressure 7" E INTEGRATED (178) 35–120 psi (2.4–8.3 bar) Excess Line for Connection 6" (152) 75 1/2" (1918) FROM FLOOR RIGHT SIDE OF OPENING RIGHT SIDE OF OPENING Electrical supply location. 6" 5 3/16" (152) (132) 3" (76) WINE AREA EXTENDS 1/2" (13) FORWARD ON FLOOR UNDERCOUNTER Water supply location. 42 | Sub-Zero Customer Care 800.222.7820 36" (914) PRO 48 REFRIGERATION BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER subzero.com/specs | 43 INTEGRATED REFRIGERATION BUILT-IN Integrated Refrigeration With custom front panels and hardware, Sub-Zero invented integrated columns, tall and drawer models that disappear into the decor. Integrated units fit flush with other cabinets, making integrated refrigeration as practical and beautiful in the master suite, bar or theatre room as in the kitchen. KEY FEATURES Custom front panels and hardware allow for infinite design options. • Point-of-use refrigeration that can be placed anywhere in the home. • Dual refrigeration; two compressors preserve food’s goodness in self-contained compartments. • Energy efficient; many models are ENERGY STAR® qualified. • Star-K certified. PRO 48 • INTEGRATED MODELS INTEGRATED IC-18FI IC-24R, IC-24FI IC-30R(ID), IC-30FI IC-36R(ID) IT-30R(ID), IT-30FI, IT-30CI(ID) IT-36R(ID), IT-36CI(ID) WINE ID-24R, ID-24F(I) ID-27R ID-30R(P), ID-30F(I), ID-30C(I) ID-36R(P), ID-36C(I) UNDERCOUNTER subzero.com/specs | 45 BUILT-IN INTEGRATED REFRIGERATION Specifications Overall Dimensions COLUMN INTERIOR CAPACITY PRO 48 COLUMN IC-18FI IC-24R IC-24FI IC-30R(ID) IC-30FI IC-36R(ID) TALL ID-24R ID-24F(I) ID-27R ID-30R(P) ID-30F(I) ID-30C(I) ID-36R(P) ID-36C(I) 8.4 (238) W 24" (610) 4 1/2" (114) 12.3 (348) 17.3 (490) 15.3 (433) 21.4 (606) F CU FT (L) 16.5 (467) 10.6 (300) 20.5 (580) 13.3 (377) R CU FT (L) 15.1 (428) 5.0 (142) 84"* 69 1/2" (2134) (1765) 6.4 (181) F CU FT (L) 4.0 (113) 3.8 (108) 4.6 (130) 5.2 (147) 3.0 (85) 6.6 (187) 3.4 (96) 4.9 (139) 2.0 (57) 2.5 (71) SHIPPING WEIGHT COLUMN IC-18FI IC-24R, IC-24FI IC-30R(ID), IC-30FI IC-36R(ID) TALL LB (KG) 260 (118) 340 (154) 400 (181) 440 (200) 3 5/8" (92) *83 1/2" (2121) MIN TO 84 1/2" (2146) MAX A LB (KG) IT-30R(ID), IT-30FI, IT-30CI(ID) IT-36R(ID), IT-36CI(ID) DRAWER WINE F CU FT (L) 12.9 (365) R CU FT (L) IT-30R(ID) IT-30FI IT-30CI(ID) IT-36R(ID) IT-36CI(ID) DRAWER INTEGRATED R CU FT (L) ID-24R, ID-24F(I) ID-27R ID-30R(P), ID-30F(I), ID-30C(I) ID-36R(P), ID-36C(I) 13/4" (45) 400 (181) 460 (209) LB (KG) 170 (77) 190 (86) 210 (95) 250 (113) IMPORTANT NOTE: Overall dimensions do not include panels or handles. Dimensions will vary with panel thickness. B COLUMN MODEL UNDERCOUNTER IC-18FI IC-24R, IC-24FI IC-30R(ID), IC-30FI IC-36R(ID) 46 | Sub-Zero Customer Care 800.222.7820 W A B 18" (457) 24" (610) 30" (762) 36" (914) 2 1/2" (64) 4" (102) 5 5/8" (143) 7 1/4" (184) 16 1/2" (419) 22 1/2" (572) 28 1/2" (724) 34 1/2" (876) INTEGRATED REFRIGERATION BUILT-IN Overall Dimensions TALL DRAWER W 24" (610) W 24" (610) 1/4" (6) 4 1/2" (114) 13 5/16" (338) (876) 84"* 44 7/8" (2134) (1140) 3/8" (10) PRO 48 34 1/2"* 10 9/16" (268) 3 5/8" (92) *34" (864) MIN TO 35" (889) MAX 3/8" (10) 13 5/16" (338) 3/8" (10) INTEGRATED 10 9/16" (268) 18 3/8" (476) 3 5/8" (92) *83 1/2" (2121) MIN TO 84 1/2" (2146) MAX DRAWER A MODEL 13/4" (45) ID-24R, ID-24F(I) ID-27R ID-30R(P), ID-30F(I), ID-30C(I) ID-36R(P), ID-36C(I) W 24" (610) 27" (686) 30" (762) 36" (914) WINE 18 3/8" B (476) TALL MODEL W A B 30" (762) 30" (762) 36" (914) 5 5/8" (143) 5 5/8" (143) 7 1/4" (184) 28 1/2" (724) 28 1/2" (724) 34 1/2" (876) UNDERCOUNTER IT-30R(ID), IT-30FI IT-30CI(ID) IT-36R(ID), IT-36CI(ID) subzero.com/specs | 47 BUILT-IN INTEGRATED REFRIGERATION Opening Dimensions INTEGRATED MODELS OPENING DIMENSIONS COLUMN IC-18FI IC-24R, IC-24FI IC-30R(ID), IC-30FI IC-36R(ID) PRO 48 25" (635) OPENING DEPTH TALL TOP VIEW IT-30R(ID), IT-30FI, IT-30CI(ID) IT-36R(ID), IT-36CI(ID) DRAWER INTEGRATED ID-24R, ID-24F(I) ID-27R ID-30R(P), ID-30F(I), ID-30C(I) ID-36R(P), ID-36C(I) H W OPENING HEIGHT OPENING WIDTH W H 18" (457) 24" (610) 30" (762) 36" (914) 84" (2134) 84" (2134) 84" (2134) 84" (2134) W H 30" (762) 36" (914) 84" (2134) 84" (2134) W H 24" (610) 27" (686) 30" (762) 36" (914) 34 1/2" (876) 34 1/2" (876) 34 1/2" (876) 34 1/2" (876) The depth of each integrated model is 24" (610). Allow for panel thickness when planning the finished opening depth. A minimum 3 1/2" (89) finished return is required on all sides of the opening. Framed cabinets will require additional finished filler material behind the face frame for a proper installation. Refer to the illustration. DUAL INSTALLATION When installing two units side by side in a dual installation, the opening width is the width of the two units added together. A dual installation kit will be required for this installation. If a dual installation kit is not specified, a minimum 2" (51) filler strip is required between units. WINE SIDE VIEW FRONT VIEW NOTE: 3 1/2" (89) finished returns will be visible and should be finished to match cabinetry. 3/4" 3 1/2" (89) (19) TYPICAL 3 1/2" (89) FINISHED RETURN FINISHED RETURN W W FRAMED CABINETRY UNDERCOUNTER FRAMELESS CABINETRY 48 | FILLER Sub-Zero Customer Care 800.222.7820 Dual installation kits are available through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. For questions regarding the installation, call Sub-Zero customer care at 800-222-7820. INTEGRATED REFRIGERATION BUILT-IN Electrical Plumbing The electrical supply must be located within the shaded area shown in the illustration and chart below. A separate circuit, servicing only this appliance is required. A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation. The water supply line should be located within the shaded area shown in the illustration below. The water supply line should be connected to the house supply with an easily accessible shut-off valve. Do not use self-piercing valves. The water supply line must not interfere with installation of the anti-tip bracket. Installation must comply with all applicable electrical codes. ELECTRICAL REQUIREMENTS Electrical Supply 115 VAC, 60 Hz Service A reverse osmosis system can be used provided there is constant water pressure of 35–120 psi (2.4–8.3 bar) supplied to the unit at all times. A copper line is not recommended for this application. PRO 48 The electrical outlet must be positioned with the grounding prong to the right of the thinner blades. Installation must comply with all applicable plumbing codes. 15 amp Receptacle 3-prong grounding-type PLUMBING REQUIREMENTS 1/4" OD copper, braided stainless steel or PEX tubing Water Supply ELECTRICAL SUPPLY LOCATION Pressure MODEL A 6" (152) 9 1/2" Excess Line for Connection 36" (914) (241) 11" (279) 12 1/2" (318) 15 1/2" (394) WATER SUPPLY LOCATION MODEL A 18" Model 24" Model 30" Model 36" Model 3" (76) 5 1/2" (140) 6" (152) 9" (229) INTEGRATED 18" Model 24" Model 27" Model 30" Model 36" Model 35–120 psi (2.4–8.3 bar) LEFT SIDE OF OPENING 41/2" RIGHT SIDE OF OPENING A (114) 4 1/4" A 1/4" (6) WINE (108) FLOOR 6" (152) 3" (76) Electrical supply location. AREA EXTENDS 1/2" (13) FORWARD ON FLOOR Water supply location. UNDERCOUNTER subzero.com/specs | 49 BUILT-IN INTEGRATED REFRIGERATION Custom Panels PRO 48 For integrated models, custom door panels and handle hardware must be provided. Refer to the panel requirements chart and typical panel dimensions. TYPICAL PANEL DIMENSIONS The thickness of the custom panel can vary. A minimum 5/8" (16) thick panel is required, but the thickness can be increased provided it does not exceed the weight limit. The depth of each integrated model is 24" (610). Allow for panel thickness when planning the finished opening depth. Refer to the full-scale template on page 53. 79 7/8" 49 3/8" (2029) (1254) 13 9/16" (345) CAUTION 16 11/16" As reveals between cabinetry and the unit decrease, severe finger pinching can occur while door is closing. (424) INTEGRATED W W W Finish all sides of custom panels. They will be visible when the door/drawer is open. Column D-style handles are recommended. Door handles must be located near the edge of the panel opposite the hinge and should be centered top to bottom. Drawer handles must be located near the top edge of each panel. Stainless steel tubular and pro handles are available through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. Typical panel dimensions are based on an 84" (2134) finished height for column and tall models and 34 1/2" (876) for drawer models, with a 4" (102) toe kick and 1/8" (3) reveals. Panel dimensions must be adjusted accordingly for all other installations. Refer to the illustration for panel heights and the chart below for panel widths. Tall Drawer PANEL WIDTH PANEL REQUIREMENTS PANEL WEIGHT 18" Column 24" Column 30" Column 36" Column WINE PANEL WEIGHT 30" Tall (door) 36" Tall (door) Drawer PANEL THICKNESS All Panels MODEL MAX 45 lb (20 kg) 60 lb (27 kg) 75 lb (34 kg) 75 lb (34 kg) 18" Model 24" Model 27" Model 30" Model 36" Model W 17 3/4" (451) 23 3/4" (603) 26 3/4" (679) 29 3/4" (756) 35 3/4" (908) MAX 50 lb (22 kg) 60 lb (27 kg) 15 lb (7 kg) MIN 5/8" (16) DUAL INSTALLATION For dual installations, refer to the illustration for panel heights and the chart below for panel widths. PANEL WIDTH MODEL UNDERCOUNTER 18" Model 24" Model 27" Model 30" Model 36" Model 50 | Sub-Zero Customer Care 800.222.7820 W 17 13/16" (452) 23 13/16" (605) 26 13/16" (681) 29 13/16" (757) 35 13/16" (910) INTEGRATED REFRIGERATION BUILT-IN Custom Panels TOE KICK CLEARANCE The height of the custom door panel can extend beyond the typical panel height, provided it does not exceed the weight limit. Refer to the illustration below. The height of the toe kick area can extend beyond the typical toe kick height, provided it does not exceed the dimensions in the illustration below. Toe kick heights from 2" (51) to 3 7/8" (98) require a reduced toe kick accessory available through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. For questions regarding the installation, call Sub-Zero customer care at 800-222-7820. 1 3/4" (45) PRO 48 DOOR PANEL HEIGHT A DECORATIVE VALANCE CANNOT EXTEND BEYOND THIS PLANE 1/8" (3) DOOR PANEL 84" 24" (610) TO BACK OF UNIT (2134) HINGE VENTED LOUVERS INTEGRATED 24" (610) TO BACK OF UNIT HINGE DOOR PANEL 1 1/8" (29) MAX TOE KICK ADJUSTMENT 2" (51)* TO 6" (152) FROM FLOOR A DECORATIVE TOE KICK CANNOT EXTEND BEYOND THIS PLANE Upper valance (column and tall)—side view. *2" (51) to 3 7/8" (98) requires sales accessory. WINE Toe kick—side view. UNDERCOUNTER subzero.com/specs | 51 BUILT-IN INTEGRATED REFRIGERATION Handle Hardware Optional stainless steel tubular and pro handles are available through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. PRO 48 Refer to the chart below for the length and stud spacing of standard handles for integrated models. HANDLE LENGTH TUBULAR 50 1/8" (1273) 33 1/4" (845) 27 1/4" (692) 24 1/4" (616) 21 1/4" (540) UNDERCOUNTER 52 | 47 1/8" (1197) 30 1/4" (768) 24 1/4" (616) 21 1/4" (540) 18 1/4" (464) STUD SPACING 48 3/8" (1229) 31 1/2" (800) 25 1/2" (648) 22 1/2" (572) 19 1/2" (495) WINE INTEGRATED PRO STUD SPACING Sub-Zero Customer Care 800.222.7820 47 1/8" (1197) 30 1/4" (768) 24 1/4" (616) 21 1/4" (540) 18 1/4" (464) INTEGRATED REFRIGERATION BUILT-IN Maximum Door Opening FULL-SCALE TEMPLATE As the panel width and/or depth increases, so does the potential for panel interference. Interference may be minimized by utilizing the 90° door stop. PRO 48 3/4" (19) PANEL DOOR OPEN MAXIMUM 105° 1/8" (3) REVEAL INTEGRATED POTENTIAL INTERFERENCE DOOR CLOSED 3/4" (19) PANEL ADJACENT CABINETRY WINE POTENTIAL INTERFERENCE 0" 1" (25) UNDERCOUNTER SCALE Maximum door opening (top view). subzero.com/specs | 53 WINE STORAGE BUILT-IN Wine Storage Wine finds a well-deserved place of honor in a Sub-Zero wine storage unit. Every detail is designed to ensure better wine preservation. Cherrywood-faced racks, soft lighting, custom cabinetry if desired—Sub-Zero helps make a wine collection an element of beauty in the home. KEY FEATURES Integrated, overlay, flush inset and stainless steel design options. • Full-view glass door standard on all models. • Freestanding model 424FSG does not require panels or surrounding cabinetry. • Discreet interior lighting with illuminated display rack for prized bottles of wine. • Two independent storage zones maintain temperature, humidity and UV protection. • Roller-assembly wine racks with natural cherrywood facing have three-quarter extension for easy access. • Wine racks accommodate 750 ml bottles, half-bottles and magnums. INTEGRATED WINE STORAGE MODELS 424G 424FSG 427G 427RG WINE 315W PRO 48 • WS-30 UNDERCOUNTER subzero.com/specs | 55 BUILT-IN WINE STORAGE Overall Dimensions MODEL 315W MODEL 424G PRO 48 15 1/8" (384) 23 7/8" (606) 24" (610) 341/16" 34" (865) (864) 4" (102) INTEGRATED 24" (610) 4" (102) 16 5/8" (422) 25 3/8" (645) 1 3/4" (44) 1 3/4" (44) SPECIFICATIONS WINE STORAGE CAPACITY 315W 424G 424FSG SHIPPING WEIGHT UNDERCOUNTER 315W 424G 424FSG 56 | Sub-Zero Customer Care 800.222.7820 BOTTLES (750 ML) 26 46 46 LB (KG) 118 (54) 195 (88) 220 (100) Overall dimensions are based on the stainless steel model. Refer to page 77 for door clearance information. WINE STORAGE BUILT-IN Overall Dimensions Opening Dimensions MODEL 424FSG MODELS 315W AND 424G 24 1/4" (616) 24 5/8" (625) 24" (610) OPENING DEPTH PRO 48 34 3/16" (868) TOP VIEW 4" (102) W (876) OPENING HEIGHT OPENING WIDTH INTEGRATED SIDE VIEW 34 1/2" FRONT VIEW 25 3/8" (645) OPENING WIDTH 1 3/4" (44) MODEL 315W 424G W 15 1/4" (387) 24" (610) Freestanding model 424FSG has a finished stainless steel exterior and handles. WINE UNDERCOUNTER subzero.com/specs | 57 BUILT-IN WINE STORAGE Overall Dimensions MODEL 427G MODEL 427RG 27" (686) 24" (610) 27" (686) 14" (356) PRO 48 13/16" (21) 13/16" (21) 78 9/16" 78 9/16" (1995) (1995) 80" 80" (2032) OPENING HEIGHT (2032) OPENING HEIGHT 3/8" (10) 1/2" (13) 13 1/4" (337) INTEGRATED 10 1/4" 34 1/2" (876) (260) 20 3/8" (518) 8 15/16" 9 3/4" (227) (248) 4" HEIGHT DIMENSIONS ± 1/2" (13) 24" (610) WINE 24" (610) STORAGE CAPACITY 427G 427RG 4 5/8" (117) (117) 251/2" 191/2" 251/2" (648) (495) (648) R CU FT (L) BOTTLES (750 ML) 5.3 (150) 132 78 427G 427RG | (102) 4 5/8" SHIPPING WEIGHT 58 4" HEIGHT DIMENSIONS ± 1/2" (13) (102) SPECIFICATIONS UNDERCOUNTER 24" (610) 14" (356) Sub-Zero Customer Care 800.222.7820 LB (KG) 395 (179) 410 (186) Overall dimensions do not include panels or handles. Dimensions will vary with panel thickness. WINE STORAGE BUILT-IN Opening Dimensions MODELS 427G AND 427RG OPENING DIMENSIONS 25" (635) OPENING DEPTH MODEL W H 427G 427RG 27" (686) 27" (686) 80" (2032) 80" (2032) TOP VIEW PRO 48 The depth of each integrated model is 24" (610). Allow for panel thickness when planning the finished opening depth. DUAL INSTALLATION When installing two integrated units (models 427G and 427RG) side by side in a dual installation, the opening width is the width of the two units added together. A dual installation kit will be required for this installation. If a dual installation kit is not specified, a minimum 2" (51) filler strip is required between units. W OPENING HEIGHT OPENING WIDTH Dual installation kits are available through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. For questions regarding the installation, call Sub-Zero customer care at 800-222-7820. INTEGRATED SIDE VIEW H FRONT VIEW WINE UNDERCOUNTER subzero.com/specs | 59 BUILT-IN WINE STORAGE Overall Dimensions Opening Dimensions MODEL WS-30 MODEL WS-30 STANDARD INSTALLATION 26 3/16" (665) 30" (762) PRO 48 24" (610) OPENING DEPTH 84" TOP VIEW (2134) 73 3/4" INTEGRATED (1873) HEIGHT DIMENSIONS ± 1/2" (13) 4" (102) 23 7/8" (606) 83 3/4" W (2127) OPENING HEIGHT OPENING WIDTH 23 7/8" (606) 17" (432) 311/4" (796) WINE SIDE VIEW NOTE: Shaded line represents profile of unit. 2 3/8" (60) SPECIFICATIONS STORAGE CAPACITY WS-30 SHIPPING WEIGHT WS-30 UNDERCOUNTER FRONT VIEW OPENING WIDTH BOTTLES (750 ML) MODEL W 147 WS-30 29 1/2" (749) LB (KG) 445 (202) Overall dimensions are based on the stainless steel model. For flush inset applications, add 1/2" (13) to door clearance dimensions. 60 | Sub-Zero Customer Care 800.222.7820 If an 83" (2108) grille height is specified, the opening height must be decreased by 7/8" (22). If an 88" (2235) grille height is specified, the opening height must be increased by 4" (102). If two units are installed side by side, refer to page 62 for dual standard installations. WINE STORAGE BUILT-IN Opening Dimensions MODEL WS-30 FLUSH INSET INSTALLATION 26 3/16" (665) FLUSH INSET DEPTH 2 3/16" (56) PRO 48 FINISHED CLEATS* TOP VIEW 11/4" 1/4" (6) (32) W FLUSH INSET WIDTH INTEGRATED 84" (2134) FLUSH INSET HEIGHT 11/4" (32) 4" (102) 3" (76)* TYPICAL SIDE VIEW 2 3/16" (56) FRONT VIEW WINE *3" (76) typical depth. Shaded areas will be visible and should be finished to match cabinetry. NOTE: Shaded line represents profile of unit with 3/4" (19) panel. Dimensions assume a 3/4" (19) panel thickness. FLUSH INSET WIDTH MODEL W WS-30 32" (813) If an 83" (2108) grille height is specified, the flush inset height must be decreased by 7/8" (22). If an 88" (2235) grille height is specified, the flush inset height must be increased by 4" (102). subzero.com/specs | UNDERCOUNTER If two units are installed side by side, refer to page 63 for dual flush inset installations. 61 BUILT-IN WINE STORAGE Opening Dimensions MODEL WS-30 DUAL STANDARD INSTALLATION PRO 48 24" (610) OPENING DEPTH INTEGRATED TOP VIEW 83 3/4" W (2127) OPENING HEIGHT OPENING WIDTH WINE SIDE VIEW FRONT VIEW NOTE: Shaded line represents profile of unit. A dual installation kit will be required for this installation. OPENING WIDTH MODELS UNDERCOUNTER WS-30 and 30" Built-In WS-30 and 36" Built-In 62 | Sub-Zero Customer Care 800.222.7820 W 59 3/4" (1518) 65 3/4" (1670) WINE STORAGE BUILT-IN Opening Dimensions MODEL WS-30 DUAL FLUSH INSET INSTALLATION 26 3/16" (665) FLUSH INSET DEPTH 2 3/16" (56) PRO 48 FINISHED CLEATS* TOP VIEW 11/4" 1/4" (6) (32) W FLUSH INSET WIDTH INTEGRATED 84" (2134) FLUSH INSET HEIGHT 11/4" (32) 4" (102) 3" (76)* TYPICAL SIDE VIEW 2 3/16" (56) FRONT VIEW WINE *3" (76) typical depth. Shaded areas will be visible and should be finished to match cabinetry. NOTE: Shaded line represents profile of unit with 3/4" (19) panel. FLUSH INSET WIDTH MODELS WS-30 and 30" Built-In WS-30 and 36" Built-In W Dimensions assume a 3/4" (19) panel thickness. A dual installation kit will be required for this installation. 62 1/4" (1581) 68 1/4" (1734) UNDERCOUNTER subzero.com/specs | 63 PRO 48 BUILT-IN WINE STORAGE Electrical Custom Panels The electrical supply should be located within the shaded area shown in the illustration for your specific model. For model 315W, the electrical supply can be located anywhere on the back wall of the opening. A separate circuit, servicing only this appliance is required. A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation. For framed, overlay, integrated and flush inset applications, custom door panels must be provided. Handle hardware must also be provided for overlay, integrated and flush inset applications. Refer to panel requirements and custom panel dimensions charts for your specific model and design application. If the unit will be connected to a home security system, allow 36" (914) of excess wiring for proper connection. IMPORTANT NOTE: For models 427G and 427RG, it is critical the electrical outlet be positioned with the grounding prong to the right of the thinner blades. Installation must comply with all applicable electrical codes. ELECTRICAL REQUIREMENTS Electrical Supply 115 VAC, 60 Hz INTEGRATED Service 15 amp Receptacle 3-prong grounding-type LEFT SIDE OF OPENING LEFT SIDE OF OPENING 21/2" (64) 2" 15 1/2" (51) (394) 13" (330) 4 1/2" (114) 3" (76) 1/4" (6) WINE FLOOR FLOOR Model 424G. Models 427G and 427RG. 7" E (178) 6" UNDERCOUNTER (152) 75 1/2" (1918) FROM FLOOR RIGHT SIDE OF OPENING Model WS-30. 64 | Sub-Zero Customer Care 800.222.7820 Do not install a solid panel on a glass door unit. A solid door is available as a sales accessory (except model 315W and WS-30) and must be installed if a solid panel is being specified. Service may be required to install the door. Contact an authorized Sub-Zero dealer for more information. Overall dimensions are the same for glass and solid door panels. Finish all sides of the custom panels. They may be visible when the door is open or through the window of glass door models. Model 424FSG has a finished stainless steel exterior that is designed to be used in a freestanding application. WINE STORAGE BUILT-IN Custom Panels—315W and 424G For models 315W and 424G, the custom door panel will attach directly to the door frame with screws through a series of pre-drilled holes. Refer to the charts for panel requirements and dimensions. PANEL REQUIREMENTS 315W 424G PANEL THICKNESS All Panels A A A H A MAX 10 lb (5 kg) 10 lb (5 kg) MIN 5/8" (16) W PRO 48 PANEL WEIGHT OVERLAY PANEL DIMENSIONS 315W / 424G PANEL DIMENSIONS MODEL 315W 424G W H 15" (381) 23 3/4" (603) 30 1/16" (764) 30 1/16" (764) STILES / RAILS (MIN) 315W 424G A 2 1/4" (57) 2 1/4" (57) Models 315W and 424G can be installed flush with surrounding cabinetry. Depending on the thickness of the overlay door panel, it may be necessary to install the unit 1/4" (6) beyond the front surface of adjacent cabinetry to prevent interference when the door is opened to 145°. Refer to the full-scale template on page 77. INTEGRATED DOOR CLEARANCE WINE UNDERCOUNTER subzero.com/specs | 65 BUILT-IN WINE STORAGE Custom Panels—427G and 427RG PRO 48 For models 427G and 427RG, the custom door panel will attach directly to the door with screws through a series of pre-drilled holes. For model 427RG, the drawer panels will attach using mounting brackets supplied with the unit. Refer to the panel requirements chart and integrated panel dimensions. The thickness of the custom panel can vary. A minimum 5/8" (16) thick panel is required, but the thickness can be increased provided it does not exceed the weight limit. The depth of each model is 24" (610). Allow for panel thickness when planning the finished opening depth. CAUTION INTEGRATED When using a 3/4" (19) or thicker panel with a reveal less than 1/4" (6), panel may cause damage to the unit when door is opened to 105°. Use the built-in 90° door stop. CAUTION As reveals between cabinetry and the unit decrease, severe finger pinching can occur while door is closing. PANEL REQUIREMENTS PANEL WEIGHT Door Drawer (427RG) PANEL THICKNESS UNDERCOUNTER WINE All Panels 66 | Sub-Zero Customer Care 800.222.7820 MAX 20 lb (9 kg) 12 lb (5 kg) MIN 5/8" (16) Finish all sides of custom panels. They will be visible when the door/drawer is open. D-style handles are recommended. Door handles must be located near the edge of the panel opposite the hinge and should be centered top to bottom. Drawer handles must be located near the top edge of each panel. Stainless steel tubular and pro handles are available through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. An optional lock kit is available for models 427G and 427RG. Review the lock kit instructions to ensure your panels will allow for adequate installation. These instructions are available on our website, subzero.com/specs. WINE STORAGE BUILT-IN Custom Panels—427G and 427RG INTEGRATED PANEL DIMENSIONS B DUAL INSTALLATION For dual installations, refer to the illustration for panel heights and the chart below for panel widths. B PANEL WIDTH A A 75 7/8" A A (1927) MODEL W (1153) 427G 427RG 26 13/16" (681) 26 13/16" (681) C STILES / RAILS (MIN) 13 9/16" 427G 427RG (345) A B C 2 1/4" (57) 2 1/4" (57) 3 3/4" (95) 3 3/4" (95) 8" (203) 3" (76) PRO 48 45 3/8" 16 11/16" (424) C W 427G W 427RG INTEGRATED Typical panel dimensions are based on an 80" (2032) overall height, 4" (102) toe kick and 1/8" (3) reveals. Panel dimensions must be adjusted accordingly for all other installations. Refer to the illustration for panel heights and the chart below for panel widths. PANEL WIDTH MODEL W 427G 427RG 26 3/4" (679) 26 3/4" (679) STILES / RAILS (MIN) 427G 427RG A B C 2 1/4" (57) 2 1/4" (57) 3 3/4" (95) 3 3/4" (95) 8" (203) 3" (76) WINE UNDERCOUNTER subzero.com/specs | 67 BUILT-IN WINE STORAGE Custom Panels—427G and 427RG TOE KICK CLEARANCE The height of the custom door panel can extend beyond the typical panel height, provided it does not exceed the weight limit. Refer to the illustration below. The height of the toe kick area can extend beyond the typical toe kick height, provided it does not exceed the dimensions in the illustration below. PRO 48 DOOR PANEL HEIGHT 25" (635) TO WALL INTEGRATED UNIT (SIDE VIEW) 11/2" (38) DECORATIVE VALANCE CANNOT EXTEND BEYOND THE FRONT OF THE MOLDING 1/8" (3) DOOR PANEL OVERALL HEIGHT DECORATIVE VALANCE HEIGHT OF PANEL KICKPLATE / GRILLE CAN BE ADJUSTED FORWARD KICKPLATE / GRILLE 1/8" (3) BASE MOLDING MUST BE REMOVABLE— 4" (102) MAX HEIGHT INTEGRATED REMOVABLE MOLDING MINIMUM HEIGHT HINGE 4" (102) TO 9" (229) TYPICAL HEIGHT OF DOOR PANEL 25" (635) TO WALL FROM FLOOR INTEGRATED UNIT (SIDE VIEW) 2 5/8" (67) TO 4" (102) UNDERCOUNTER WINE Upper valance—side view. 68 | Sub-Zero Customer Care 800.222.7820 Toe kick—side view. WINE STORAGE BUILT-IN Custom Panels—WS-30 FRAMED PANEL FRAMED PANEL DIMENSIONS The framed application is an overlay model with framed design features. It is not a separate model. H A 1/4" Routing, recessing and optional extended handles may be required for finger clearance. Refer to the full-scale template on page 78. A A H PRO 48 (6), a filler material If the custom panel is thinner than must be added to achieve a proper fit. If the panel is thicker than 1/4" (6), rout an edge around the panel or mount the custom panel on a sheet of 1/4" (6) thick material and insert into the channel. A W PANEL REQUIREMENTS PANEL WEIGHT MAX Door Grille (optional) 75 lb (34 kg) 13 lb (6 kg) PANEL THICKNESS MIN 1/4" (6) FRAMED PANELS PANEL Door Grille (optional) W H 29 3/4" (756) 29 3/4" (756) 69 9/16" (1767) 8 15/16" (227) STILES / RAILS Minimum A 3 1/8" (79) INTEGRATED Framed WS-30 WINE UNDERCOUNTER subzero.com/specs | 69 BUILT-IN WINE STORAGE Custom Panels—WS-30 OVERLAY PANELS OVERLAY PANEL DIMENSIONS Overlay panels are typically created by combining a 3/4" (19) custom panel, a .10" (3) spacer panel and a 1/4" (6) backer panel. Refer to the illustrations below. H A PRO 48 PANEL REQUIREMENTS PANEL WEIGHT MAX Door Grille A A H 75 lb (34 kg) 13 lb (6 kg) PANEL THICKNESS MIN 5/8" Overlay (16) A W SPACER PANEL CUSTOM PANEL SPACER PANEL WS-30 OVERLAY PANELS CUSTOM PANEL INTEGRATED DOOR BACKER PANEL BACKER PANEL TRIM DOOR FRAME GLASS Overlay Panel Spacer Panel Backer Panel W H 30" (762) 29 1/8" (740) 29 3/4" (756) 69 3/4" (1772) 68 15/16" (1751) 69 9/16" (1767) STILES / RAILS 5/16" (8) min 1/8" (3) Panel assembly cross section (overlay). A 3 1/4" (83) Minimum 3/4" (19) typical .10" (3) 1/4" (6) Panel assembly rear view. GRILLE Overlay Panel Spacer Panel Backer Panel W H 30" (762) 29 1/8" (740) 29 3/4" (756) 9 1/4" (235)* 8 5/16" (211) 8 15/16" (227) *Panel height may be increased by 7/16" (11) to hide upper main frame. For more information, refer to the built-in panel configurator at subzero.com/trade/panels. UNDERCOUNTER WINE Grille panel dimensions are for standard 84" (2134) overall unit height. For 83" (2108) height, subtract 1" (25) from grille panel height dimensions and for 88" (2235) height, add 4" (102). A specific panel grille must be ordered for an 83" or 88" overall unit height. 70 | Sub-Zero Customer Care 800.222.7820 WINE STORAGE BUILT-IN Custom Panels—WS-30 FLUSH INSET PANELS FLUSH INSET PANEL DIMENSIONS The flush inset application is an overlay model with flush inset panels. It is not a separate model. A A A H PRO 48 The flush inset design allows custom panels to be installed flush with adjacent cabinets. Similar to overlay, flush inset panels are typically created by combining a 3/4" (19) custom panel, a .10" (3) spacer panel and a 1/4" (6) backer panel. Refer to the illustrations for overlay panels on the previous page. H For flush inset panels thicker than 3/4" (19), a 90° door stop may be required to prevent interference with adjacent cabinets. Refer to the full-scale template on page 81. A W PANEL REQUIREMENTS PANEL WEIGHT Door Grille Flush Inset 75 lb (34 kg) 13 lb (6 kg) MIN 5/8" (16) FLUSH INSET PANELS DOOR Flush Inset Panel Spacer Panel Backer Panel W H 31" (787) 29 1/8" (740) 29 3/4" (756) 69 3/4" (1772) 68 15/16" (1751) 69 9/16" (1767) STILES / RAILS A 3 3/4" (95) Minimum GRILLE Flush Inset Panel Spacer Panel Backer Panel W H 31" (787) 29 1/8" (740) 29 3/4" (756) 9 1/4" (235) 8 5/16" (211) 8 15/16" (227) INTEGRATED PANEL THICKNESS WS-30 MAX Grille panel dimensions are for standard 84" (2134) overall unit height. For 83" (2108) height, subtract 1" (25) from grille panel height dimensions and for 88" (2235) height, add 4" (102). A specific panel grille must be ordered for an 83" or 88" overall unit height. WINE UNDERCOUNTER subzero.com/specs | 71 BUILT-IN WINE STORAGE Custom Panels—WS-30 FLUSH INSET PANEL OFFSETS TOP VIEW The illustrations provide panel offsets and reveals for model WS-30 in a flush inset application. Refer to the chart below for reference to the illustrations. CABINETRY DOOR / DRAWER / GRILLE 1/2" (13) BACKER SPACER CABINETRY PRO 48 PANEL OFFSET FLUSH INSET Door / Grille Sides Grille Top Grille Bottom / Door Top Door Bottom ILLUS 1/8" 5/16" (3) (8) GRILLE FLUSH INSET PANEL A B C D 5/16" (8) 1/2" (13) 5/8" (16) SIDE VIEW Illus. A Illus. B DOOR / DRAWER INTEGRATED GRILLE 5/16" (8) 5/32" (4) 5/16" (8) 1/2" (13) DOOR 3/32" 5/16" (2) (8) SIDE VIEW SIDE VIEW UNDERCOUNTER WINE Illus. C 72 | Sub-Zero Customer Care 800.222.7820 Illus. D 3/32" (2) WINE STORAGE BUILT-IN Custom Panels—WS-30 DUAL FLUSH INSET PANEL DIMENSIONS DUAL INSTALLATIONS Dual installation kits are available through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. For questions regarding the installation, call Sub-Zero customer care at 800-222-7820. For dual standard installations, panel dimensions are the same as for single installations. Refer to the chart on the previous page. Panel dimensions and offsets for dual flush inset installations are listed on the following pages. H A A A H PRO 48 If two models WS-30 or a model WS-30 and built-in unit are installed side by side, a dual installation kit may be required. Installations without a custom filler strip require a dual installation kit. If a dual installation kit is not specified, a 2" (51) filler strip is recommended between units. Dual installations without a filler strip can only be accomplished using two units with opposite hinges. Refer to the illustrations below. A W WS-30 MODEL WS-30 DOOR W H 30 1/2" (775) 29 1/8" (740) 29 3/4" (756) 69 3/4" (1772) 68 15/16" (1751) 69 9/16" (1767) STILES / RAILS A 3 3/4" (95) Minimum GRILLE Flush Inset Panel Spacer Panel Backer Panel WITHOUT FILLER STRIP H 9 1/4" (235) 8 5/16" (211) 8 15/16" (227) Grille panel dimensions are for standard 84" (2134) overall unit height. For 83" (2108) height, subtract 1" (25) from grille panel height dimensions and for 88" (2235) height, add 4" (102). A specific panel grille must be ordered for an 83" or 88" overall unit height. WINE Opposite hinges. FILLER STRIP W 30 1/2" (775) 29 1/8" (740) 29 3/4" (756) INTEGRATED Flush Inset Panel Spacer Panel Backer Panel Same side hinges. UNDERCOUNTER subzero.com/specs | 73 BUILT-IN WINE STORAGE Custom Panels—WS-30 DUAL FLUSH INSET PANEL OFFSETS TOP VIEW The illustrations provide panel offsets and reveals for model WS-30 in a dual flush inset application. Refer to the chart below for reference to the illustrations. TOP VIEW DOOR / DRAWER / GRILLE DUAL TRIM BACKER SPACER CABINETRY DOOR DOOR PRO 48 PANEL OFFSET DUAL FLUSH INSET Door (hinge) / Grille Sides Door (handle) Sides Grille Top Grille Bottom / Door Top Door Bottom ILLUS FLUSH INSET PANEL A B C D E 5/16" (8) 1/2" (13) 5/16" (8) 1/8" (3) 5/8" (16) 1/4" (6) REVEAL Illus. A Illus. B CABINETRY INTEGRATED 1/2" (13) GRILLE GRILLE 1/8" 5/16" (3) (8) 1/2" (13) DOOR Illus. D WINE DOOR / DRAWER 5/16" (8) SIDE VIEW UNDERCOUNTER Illus. E 74 | Sub-Zero Customer Care 800.222.7820 3/32" (2) 3/32" 5/16" (2) (8) SIDE VIEW SIDE VIEW Illus. C 5/16" (8) 5/32" (4) WINE STORAGE BUILT-IN Custom Panels—WS-30 Handle Hardware SIDE PANEL Optional stainless steel tubular and pro handles are available through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. The custom side panel must be a minimum of 24" (610) deep and 1/2" (13) thick. Routing will be necessary for the side panel to fit flush against the side of the unit. Refer to the illustrations below. STANDARD HANDLES 315W, 424G, 424FSG Tubular Pro 427RG (DRAWER) Tubular Pro 24" (610) 427G, 427RG (DOOR) Tubular Pro FRONT OF SIDE PANEL LENGTH STUD SPACING 24 3/16" (614) 21" (533) 16 1/4" (413) 19 11/16" (500) LENGTH STUD SPACING 24 3/16" (614) 21" (533) 16 1/4" (413) 19 11/16" (500) LENGTH STUD SPACING 41 3/16" (1046) 39 9/16" (1006) 33 1/4" (845) 38 5/16" (973) LENGTH STUD SPACING 63 7/8" (1622) 45 3/16" (1147) 43 7/8" (1114) 43 7/8" (1114) PRO 48 When installing model WS-30 with a custom side panel, an accessory kit is required. Stainless steel and white enamel side panels are available through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. Refer to the chart below for the length and stud spacing of standard handles for wine storage models. 1" (25) 1 7/8" (48) WS-30 1/8" (3) 1/2" (13) ROUT TO 1/8" (3) 1 7/8"(48) 1" (25) 84" MAIN FRAME INTEGRATED Tubular Pro SIDE PANEL ROUTING (2134) Routing detail. WINE 4" (102) OPTIONAL TOE KICK CUT-OUT 2 5/8" (67) Side panel dimensions. UNDERCOUNTER subzero.com/specs | 75 BUILT-IN WINE STORAGE Wine Rack Wood Facing WOOD FACING WIDTH The natural cherrywood facing on wine storage racks can be stained and sealed, or replaced with wood more complementary to surrounding cabinetry. Refer to the full-scale template below for profile dimensions of the wood facing and the chart for widths. MODEL PRO 48 FULL-SCALE TEMPLATE 1/2" 5/8" (13) (16) 7/64" (3) 7/64" (3) 1/4" (6) 11/2" (38) INTEGRATED 11/16" 27/32" (27) 5/64" (2) (21) 23/64" 23/64" (9) (9) 9/16" 9/16" (14) (14) IW MODELS 400 SERIES UNDERCOUNTER WINE Wine rack wood facing profile. 76 | Sub-Zero Customer Care 800.222.7820 5/64" (2) 315W 424G, 424FSG 427G, 427RG WS-30 WIDTH 10 15/16" (278) 19 1/2" (495) 20 15/16" (532) 24 9/16" (624) WINE STORAGE BUILT-IN Door Clearance—315W and 424G FULL-SCALE TEMPLATE To allow for a 145° door opening, the unit should extend a minimum of 1/4" (6) beyond the front surface of adjacent cabinetry. The unit can be installed flush, however, there is potential for interference with the panel if the door is opened past 90°. PRO 48 UNDERCOUNTER UNIT ADJACENT CABINETRY INTEGRATED DOOR CLOSED 1/2" (13) 3/4" (19) DOOR PANEL 1/4" (6) 1/8" (3) WINE HINGE AT 145° OPENING (DOOR OPENS PAST 145°) 0" 1" (25) UNDERCOUNTER SCALE 145° door opening (top view). subzero.com/specs | 77 BUILT-IN WINE STORAGE Framed Panel—WS-30 PRO 48 FULL-SCALE TEMPLATE OPTIONAL EXTENDED FULL-LENGTH HANDLE INTEGRATED STANDARD FULL-LENGTH HANDLE 1" 2" 3" (25) (51) (76) 11/4" (32) PANEL 1" (25) PANEL 3/4" (19) PANEL 1/2" (13) PANEL WINE 1/4" (6) FRAMED PANEL DOOR UNDERCOUNTER Framed panel thickness. 78 | Sub-Zero Customer Care 800.222.7820 WINE STORAGE BUILT-IN Overlay and Flush Inset Panels—WS-30 FULL-SCALE TEMPLATE Overlay and flush inset panels must be a minimum of 5/8" (16) thick to support mounting the handle. Panel thickness does not include backer and spacer panel. Mount handle close to the opening edge of the door. PRO 48 DEPTH OF TUBULAR AND PRO HANDLES 2" 3" (51) (76) INTEGRATED 1" (25) 11/4" (32) PANEL 1" (25) PANEL 3/4" (19) PANEL .10" (3) SPACER PANEL 1/4" (6) BACKER PANEL WINE DOOR Overlay and flush inset panel thickness. UNDERCOUNTER subzero.com/specs | 79 BUILT-IN WINE STORAGE Overlay Application—WS-30 FULL-SCALE TEMPLATE 237/8" (606) TO REAR OF UNIT OVERALL WIDTH OF UNIT PRO 48 0" (0) 1/4" (6) 1/2" (13) 3/4" (19) 1" (25) 11/4" (32) 11/2" (38) 13/4" (44) INTEGRATED 2" (51) 21/4" (57) 21/2" (63) 23/4" (70) 3" (76) 31/4" (83) 31/2" (89) WINE 1" (25) THICK PANEL 3/4" (19) THICK OVERLAY PANEL (TYPICAL) 1/4" (6) BACKER UNDERCOUNTER PANEL 0" 1" (25) SCALE 90° door opening (top view). 80 | Sub-Zero Customer Care 800.222.7820 WINE STORAGE BUILT-IN Flush Inset Application—WS-30 FULL-SCALE TEMPLATE 24" (610) TO BACK WALL For panels thicker than 3/4" (19), a 90° door stop may be required to prevent interference with adjacent cabinets. 1 1/4" (32) PRO 48 2 3/16" (56) ASSUMES 3/4" (19) FLUSH INSET PANEL THICKNESS INTEGRATED WINE 1" (25) THICK PANEL 3/4" (19) THICK FLUSH INSET PANEL (TYPICAL) 1/4" (6) BACKER PANEL 0" 1" (25) UNDERCOUNTER SCALE 110° door opening (top view). subzero.com/specs | 81 BUILT-IN WINE STORAGE PRO 48 FILLER STRIP 11/4" (32) DOOR CLOSED WINE INTEGRATED APPROX PROFILE OF STAINLESS STEEL WRAPPED DOOR AND HANDLE Dual Standard Installation—WS-30 FULL-SCALE TEMPLATE Typical framed, overlay or stainless steel dual installation with filler strip at maximum 110° door opening. Panel thickness may require a 90° door stop. UNDERCOUNTER 0" 1" (25) SCALE Dual standard installation (top view). 82 | Sub-Zero Customer Care 800.222.7820 DOOR OPEN 110° WINE STORAGE BUILT-IN FILLER STRIP PRO 48 1 1/2" (38) 1/2" (13) PROFILE OF 3/4" (19) FLUSH INSET PANEL AND TUBULAR HANDLE DOOR CLOSED INTEGRATED WINE Dual Flush Inset Installation—WS-30 DOOR OPEN 110° FULL-SCALE TEMPLATE Typical flush inset dual installation with filler strip at maximum 110° door opening. Panel thickness may require a 90° door stop. 0" 1" (25) UNDERCOUNTER SCALE Dual flush inset installation (top view). subzero.com/specs | 83 UNDERCOUNTER REFRIGERATION BUILT-IN Undercounter Refrigeration Sub-Zero undercounter refrigeration is a helpful addition to a master suite, bar, home office or media room. In the kitchen, a high-volume ice machine is a must for entertaining. The design flexibility of these compact yet roomy units makes them all the more welcome in any room or outdoor kitchen. They are ready to be fitted with a custom cabinet panel or can be ordered with a stainless steel panel. KEY FEATURES Overlay and stainless steel design applications. • Handle options coordinate with handles of Wolf cooking products. • Models UC-24RO and UC-15I(P)O are UL approved for outdoor use. • Energy efficient; many models are ENERGY STAR® qualified. • Star-K certified (except ice machine models). PRO 48 • UNDERCOUNTER MODELS UC-24BG UC-24C(I) UC-24RO UC-15I(P) UC-15I(P)O INTEGRATED UC-24R WINE UNDERCOUNTER subzero.com/specs | 85 BUILT-IN UNDERCOUNTER REFRIGERATION Overall Dimensions UNDERCOUNTER MODELS PRO 48 23 7/8" (606) ICE MACHINE 14 3/4" (375) 24" (610) 23" (584) 34" 33 5/8" (864) (854) 4" (102) INTEGRATED 4" (102) 18" (457) 25 3/8" (645) 6" (152) 26" (660) 8" (203) WINE SPECIFICATIONS SPECIFICATIONS INTERIOR CAPACITY R CU FT (L) UC-24R, UC-24RO UC-24BG UC-24C(I) 5.7 (161) 6.0 (170) 3.6 (102) SHIPPING WEIGHT UC-24R, UC-24BG, UC-24C(I), UC-24RO UNDERCOUNTER Refer to page 91 for door clearance information. 86 | Sub-Zero Customer Care 800.222.7820 F CU FT (L) 1.1 (31) STORAGE CAPACITY LB (KG) UC-15I(P), UC-15I(P)O 26 (12) SHIPPING WEIGHT LB (KG) UC-15I(P), UC-15I(P)O 100 (45) LB (KG) 130 (59) Model UC-15I overall dimensions do not include panel or handle. UNDERCOUNTER REFRIGERATION BUILT-IN Opening Dimensions DUAL INSTALLATION UNDERCOUNTER MODELS 24" (610) OPENING DEPTH TOP VIEW 34 1/2" W (876) OPENING HEIGHT OPENING WIDTH INTEGRATED SIDE VIEW Dual installation kits are available through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. For questions regarding the installation, call Sub-Zero customer care at 800-222-7820. PRO 48 If two units are installed side by side, a dual installation kit may be required. Installations without a custom filler strip require a dual installation kit. If a dual installation kit is not specified, a 2" (51) filler strip is recommended between units. Dual installations without a filler strip can only be accomplished using two units with opposite hinges. Refer to the illustrations below. FRONT VIEW OPENING WIDTH MODEL UC-24R UC-24C(I) UC-24BG UC-24RO ICE MACHINE UC-15I(P) UC-15I(P)O W 24" (610) 24" (610) 24" (610) 24" (610) WITHOUT FILLER STRIP Opposite hinges. FILLER STRIP Same side hinges. W 15 1/4" (387) 15 1/4" (387) WINE UNDERCOUNTER subzero.com/specs | 87 BUILT-IN UNDERCOUNTER REFRIGERATION Electrical PRO 48 The electrical supply should be located within the shaded area shown in the illustration. For ice machine models, it is recommended that electrical supply be placed in an adjacent cabinet. A separate circuit, servicing only this appliance is required. IMPORTANT NOTE: For outdoor models UC-24RO and UC-15I(P)O, a ground fault circuit interrupter (GFCI) is required to reduce the risk of electrical shock. A GFCI is not recommended for use with other undercounter models and may cause interruption of operation. Installation must comply with all applicable electrical codes. INTEGRATED LEFT SIDE OF OPENING 2" 15 1/2" (51) (394) 3" (76) FLOOR UNDERCOUNTER WINE Electrical supply location. 88 | Sub-Zero Customer Care 800.222.7820 ELECTRICAL REQUIREMENTS Electrical Supply Service Receptacle 115 VAC, 60 Hz 15 amp 3-prong grounding-type UNDERCOUNTER REFRIGERATION BUILT-IN Plumbing IMPORTANT NOTE: A reverse osmosis system can be used provided there is constant water pressure as indicated in the chart below at all times. A copper line is not recommended for this application. ICE MACHINE DRAIN Ice machine models can be ordered with or without a drain pump. Models without a pump will drain water by gravity. A drain must be installed. The drain and inlet water tubes must be plumbed before connecting to the ice machine. For the gravity drain, horizontal drain lines must have a 1/4" (6) per 12" (305) fall. An air gap will likely be required between the unit and drain. A stand pipe with a trap below is acceptable for the drain. PRO 48 The water supply line should be located within the shaded area shown in the illustrations below. The water supply line should be connected to the house supply with an easily accessible shut-off valve between the supply and the unit. Do not use self-piercing valves. A saddle valve kit is available through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. PLUMBING REQUIREMENTS 1/4" Water Supply OD copper, braided stainless steel or PEX tubing Pressure (UC-24CI) 20–100 psi (1.4–6.9 bar) Pressure (UC-15I) 20–80 psi (1.4–5.5 bar) INTEGRATED Excess Line for Connection 36" (914) LEFT SIDE OF OPENING 8" 1/2" (13) 2" 15 1/2" (51) (394) (203) LOCATION OF WATER LINE 3" (76) Model UC-24CI. TOP VIEW WINE AREA EXTENDS 1/2" (13) FORWARD ON FLOOR Ice machine. UNDERCOUNTER subzero.com/specs | 89 BUILT-IN UNDERCOUNTER REFRIGERATION Custom Panels For overlay undercounter models, custom door panels and handle hardware must be provided. Refer to the charts for panel requirements and dimensions. PRO 48 Finish all sides of the custom panels. They may be visible when the door is open or through the window of glass door models. PANEL REQUIREMENTS PANEL WEIGHT UC-24R, UC-24C(I) UC-24BG UC-15I(P) PANEL THICKNESS UNDERCOUNTER WINE INTEGRATED All Panels 90 | Sub-Zero Customer Care 800.222.7820 MAX 20 lb (9 kg) 10 lb (5 kg) 15 lb (7 kg) MIN 5/8" (16) MODEL UC-24BG For model UC-24BG, the custom door panel will attach directly to the door frame with screws through a series of pre-drilled holes. Refer to the illustration below. Do not install a solid panel on a glass door unit. A solid door is available as a sales accessory and must be installed if a solid panel is being specified. Service may be required to install the door. Contact an authorized Sub-Zero dealer for more information. Overall dimensions are the same for glass and solid door panels. UNDERCOUNTER REFRIGERATION BUILT-IN Custom Panels Handle Hardware OVERLAY PANEL DIMENSIONS Optional stainless steel tubular and pro handles are available through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. A H A A H Refer to the chart below for the length and stud spacing of standard handles for undercounter models. A UC-24R / UC-24C(I) UC-15I(P) W HANDLE LENGTH UC-24BG TUBULAR 24 3/16" (614) PRO PANEL DIMENSIONS MODEL UC-24R UC-24C(I) UC-24BG UC-15I(P) STILES / RAILS (MIN) UC-24BG W 23 3/4" (603) 23 3/4" (603) 23 3/4" (603) 15" (381) H 30 1/16" 21" (533) STUD SPACING PRO 48 W 16 1/4" (413) STUD SPACING 19 11/16" (500) (764) 30 1/16" (764) 30 1/16" (764) 30 3/8" (772) A 2 1/4" (57) INTEGRATED DOOR CLEARANCE Undercounter models can be installed flush with surrounding cabinetry. Depending on the thickness of the custom door panel, it may be necessary to install the unit 1/4" (6) beyond the front surface of adjacent cabinetry to prevent interference when the door is opened to 145°. Refer to the full-scale template on page 93. WINE UNDERCOUNTER subzero.com/specs | 91 BUILT-IN UNDERCOUNTER REFRIGERATION Wine Rack Wood Facing FULL-SCALE TEMPLATE WOOD FACING WIDTH The natural cherrywood facing on wine storage racks can be stained and sealed, or replaced with wood more complementary to surrounding cabinetry. Refer to the full-scale template below for profile dimensions of the wood facing and the chart for widths. MODEL WIDTH 19 1/2" (495) 19 1/2" (495) PRO 48 UC-24BG UC-24C(I) 1/2" 5/8" (13) (16) 7/64" (3) 7/64" (3) 1/4" (6) 11/2" (38) INTEGRATED 11/16" 27/32" (27) 5/64" (2) (21) 23/64" 23/64" (9) (9) 9/16" 9/16" (14) (14) IW MODELS 5/64" (2) 400 SERIES UNDERCOUNTER WINE Wine rack wood facing profile. Sub-Zero, Sub-Zero & Design, Dual Refrigeration, The Living Kitchen, Great American Kitchens The Fine Art of Kitchen Design, and Ingredients are registered trademarks and service marks of Sub-Zero, Inc. Wolf, Wolf & Design, Wolf Gourmet, W & Design and the color red as applied to knobs are registered trademarks and service marks of Wolf Appliance, Inc. All other trademarks or registered trademarks are property of their respective owners in the United States and other countries. 92 | Sub-Zero Customer Care 800.222.7820 UNDERCOUNTER REFRIGERATION BUILT-IN Door Clearance—Undercounter Models FULL-SCALE TEMPLATE To allow for a 145° door opening, the unit should extend a minimum of 1/4" (6) beyond the front surface of adjacent cabinetry. The unit can be installed flush, however, there is potential for interference with the panel if the door is opened past 90°. PRO 48 UNDERCOUNTER UNIT ADJACENT CABINETRY INTEGRATED DOOR CLOSED 1/2" (13) 3/4" (19) DOOR PANEL 1/4" (6) 1/8" (3) WINE HINGE AT 145° OPENING (DOOR OPENS PAST 145°) 0" 1" (25) UNDERCOUNTER SCALE 145° door opening (top view). subzero.com/specs | 93 Sub-Zero Residential Limited Warranty FOR RESIDENTIAL USE FULL TWO YEAR WARRANTY* For two years from the date of original installation, this Sub-Zero product warranty covers all parts and labor to repair or replace, under normal residential use, any part of the product that proves to be defective in materials or workmanship. All service provided by Sub-Zero under the above warranty must be performed by Sub-Zero factory certified service, unless otherwise specified by Sub-Zero, Inc. Service will be provided during normal business hours. FULL FIVE YEAR SEALED SYSTEM WARRANTY For five years from the date of original installation, this Sub-Zero product warranty covers all parts and labor to repair or replace, under normal residential use, these parts that prove to be defective in materials or workmanship: compressor, condenser, evaporator, drier and all connecting tubing. All service provided by Sub-Zero under the above warranty must be performed by Sub-Zero factory certified service, unless otherwise specified by Sub-Zero, Inc. Service will be provided during normal business hours. LIMITED TWELVE YEAR SEALED SYSTEM WARRANTY For twelve years from the date of original installation, Sub-Zero will repair or replace the following parts that prove to be defective in materials or workmanship: compressor, condenser, evaporator, drier and all connecting tubing. If the owner uses Sub-Zero factory certified service, the service provider will repair or replace these parts with the owner paying for all other costs, including labor. If the owner uses non-certified service, the owner must contact Sub-Zero, Inc. (using the information below) to receive repaired or replacement parts. Sub-Zero will not reimburse the owner for parts purchased from non-certified service or other sources. TERMS APPLICABLE TO EACH WARRANTY The warranty applies only to products installed for normal residential use. The warranty applies only to products installed in any one of the fifty states of the United States, the District of Columbia or the ten provinces of Canada. This warranty does not cover any parts or labor to correct any defect caused by negligence, accident or improper use, maintenance, installation, service or repair. THE REMEDIES DESCRIBED ABOVE FOR EACH WARRANTY ARE THE ONLY ONES THAT SUB-ZERO, INC. WILL PROVIDE, EITHER UNDER THIS WARRANTY OR UNDER ANY WARRANTY ARISING BY OPERATION OF LAW. SUB-ZERO, INC. WILL NOT BE RESPONSIBLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES ARISING FROM THE BREACH OF THIS WARRANTY OR ANY OTHER WARRANTY, WHETHER EXPRESS, IMPLIED OR STATUTORY. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other legal rights that vary from state to state. To receive parts and/or service and the name of Sub-Zero factory certified service nearest you, contact Sub-Zero, Inc., P.O. Box 44848, Madison, WI 53744; check the contact & support section of our website, subzero.com, email us at [email protected] or call 800-222-7820. *Stainless steel (doors, panels, handles, product frames and interior surfaces) are covered by a limited 60-day parts and labor warranty for cosmetic defects. *Replacement water filters and air purification cartridges are not covered by the product warranty. Sub-Zero Outdoor Limited Warranty* FOR RESIDENTIAL USE FULL ONE YEAR WARRANTY** For one year from the date of original installation, this Sub-Zero product warranty covers all parts and labor to repair or replace, under normal residential use, any part of the product that proves to be defective in materials or workmanship. All service provided by Sub-Zero under the above warranty must be performed by Sub-Zero factory certified service, unless otherwise specified by Sub-Zero, Inc. Service will be provided during normal business hours. FULL FIVE YEAR SEALED SYSTEM WARRANTY For five years from the date of original installation, this Sub-Zero product warranty covers all parts and labor to repair or replace, under normal residential use, these parts that prove to be defective in materials or workmanship: compressor, condenser, evaporator, drier and all connecting tubing. All service provided by Sub-Zero under the above warranty must be performed by Sub-Zero factory certified service, unless otherwise specified by Sub-Zero, Inc. Service will be provided during normal business hours. TERMS APPLICABLE TO EACH WARRANTY The warranty applies only to products installed for normal residential use. The warranty applies only to products installed in any one of the fifty states of the United States, the District of Columbia or the ten provinces of Canada. This warranty does not cover any parts or labor to correct any defect caused by negligence, accident or improper use, maintenance, installation, service or repair. THE REMEDIES DESCRIBED ABOVE FOR EACH WARRANTY ARE THE ONLY ONES THAT SUB-ZERO, INC. WILL PROVIDE, EITHER UNDER THIS WARRANTY OR UNDER ANY WARRANTY ARISING BY OPERATION OF LAW. SUB-ZERO, INC. WILL NOT BE RESPONSIBLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES ARISING FROM THE BREACH OF THIS WARRANTY OR ANY OTHER WARRANTY, WHETHER EXPRESS, IMPLIED OR STATUTORY. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other legal rights that vary from state to state. To receive parts and/or service and the name of Sub-Zero factory certified service nearest you, contact Sub-Zero, Inc., P.O. Box 44848, Madison, WI 53744; check the contact & support section of our website, subzero.com, email us at [email protected] or call 800-222-7820. *Product must be approved for outdoor use, designated by model and serial number. **Stainless steel (doors, panels, handles, product frames and interior surfaces) are covered by a limited 60-day parts and labor warranty for cosmetic defects. **Replacement water filters are not covered by the product warranty. SUB-ZERO, INC. P.O. BOX 44848 MADISON, WI 53744 SZDGIP2 10 / 2014 SUBZERO.COM 800.222.7820
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project