U-Line | U-3018CLRINT-00B | User Guide Integrated Solid | U-Line U-3018CLRINT-00B User Guide Integrated Solid

USER GUIDE
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
RIGHT PRODUCT. RIGHT PLACE. RIGHT TEMPERATURE. SINCE 1962.
Modular 3000 Series
•
3018CLR
•
18" Clear Ice Machine
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Contents
Intro
Maintenance
Cleaning
Safety
Safety and Warning
Cleaning Condenser
Disposal and Recycling
Extended Non-Use
Installation
Service
Environmental Requirements
Troubleshooting
Electrical
Warranty
Cutout Dimensions
Product Dimensions
Side by Side Installation
Water Hookup
Drain
Drain Pump
Anti-Tip Bracket
General Installation
Integrated Panel Dimensions
Integrated Grille / Plinth Dimensions
Integrated Panel Installation
Grille / Plinth Installation
Door Swing
Door Stop
Door Adjust
Operating Instructions
First Use
Control Operation
Ice
Sabbath Mode
Airflow and Product Loading
USER GUIDE
u-line.com
WELCOME TO U-LINE
Congratulations on your U-Line purchase. Your product comes from a company with over five decades and three generations
of premium modular ice making, refrigeration, and wine preservation experience. U-Line continues to be the American
leader, delivering versatility and flexibility for multiple applications including residential, light commercial, outdoor and marine
use. U-Line’s complete product collection includes modular Wine Captain® Models, Beverage Centers, Clear Ice Machines,
Crescent Ice Makers, Glass & Solid Door Refrigerators, Drawer Models, Freezers, and Combo® Models.
U-Line has captivated those with an appreciation for the finer things with exceptional functionality, style, inspired innovations
and attention to even the smallest details. We are known and respected for our unwavering dedication to product design,
quality and selection. U-Line is headquartered in Milwaukee, Wisconsin and has shipped product to five continents for over
two decades and is proud to have the opportunity to ship to you.
PRODUCT INFORMATION
Looking for additional information on your product? User Guides, Quick Reference Guides, CAD Drawings, Compliance
Documentation, and Product Warranty information are all available for reference and download at u-line.com.
PROPERTY DAMAGE / INJURY CONCERNS
In the unlikely event property damage or personal injury is suspected related to a U-Line product, please take the following
steps:
1. U-Line Customer Care must be contacted immediately at +1.800.779.2547.
2. Service or repairs performed on the unit without prior written approval from U-Line is not permitted. If the unit has been
altered or repaired in the field without prior written approval from U-Line, claims will not be eligible.
SERVICE INFORMATION
Answers to Customer Frequently Asked Questions are available at u-line.com under Customer Care or you may contact our
Customer Care group directly, contact information below.
GENERAL INQUIRIES
SERVICE & PARTS ASSISTANCE
U-Line Corporation
Monday - Friday 8:00 am to 5:30 pm CST
8900 N. 55th Street
T: +1.800.779.2547
Milwaukee, Wisconsin 53223 USA
F: +1.414.354.5696
Monday - Friday 8:00 am to 4:30 pm CST
Service Email: onlineservice@u-line.com
T: +1.414.354.0300
Parts Email: onlineparts@u-line.com
F: +1.414.354.7905
Email: sales@u-line.com
u-line.com
CONNECT WITH US
Designed, engineered and assembled in WI, USA
Introduction 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Safety and Warning
NOTICE
Please read all instructions before installing,
operating, or servicing the appliance.
Use this appliance for its intended purpose only and follow
these general precautions with those listed throughout this
guide:
SAFETY ALERT DEFINITIONS
Throughout this guide are safety items labeled with a
Danger, Warning or Caution based on the risk type:
! DANGER
Danger means that failure to follow this safety
statement will result in severe personal injury or
death.
! WARNING
Warning means that failure to follow this safety
statement could result in serious personal injury
or death.
! CAUTION
Caution means that failure to follow this safety
statement may result in minor or moderate
personal injury, property or equipment damage.
Safety and Warning 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Disposal and Recycling
! DANGER
RISK OF CHILD ENTRAPMENT. Before you throw
away your old refrigerator or freezer, take off
the doors and leave shelves in place so children
may not easily climb inside.
If the unit is being removed from service for disposal,
check and obey all federal, state and local regulations
regarding the disposal and recycling of refrigeration
appliances, and follow these steps completely:
1. Remove all consumable contents from the unit.
2. Unplug the electrical cord from its socket.
3. Remove the door(s)/drawer(s).
Disposal and Recycling 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Environmental Requirements
This model is intended for indoor/interior applications only
and is not to be used in installations that are open/
exposed to natural elements.
This unit is designed to operate between 50°F (10°C) and
100°F (38°C). Higher ambient temperatures may reduce
the unit’s ability to reach low temperatures and/or reduce
ice production on applicable models.
For best performance, keep the unit out of direct sunlight
and away from heat generating equipment.
In climates where high humidity and dew points are
present, condensation may appear on outside surfaces.
This is considered normal. The condensation will
evaporate when the humidity drops.
! CAUTION
Damages caused by ambient temperatures of
40°F (4°C) or below are not covered by the
warranty.
Environmental Requirements 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Electrical
! WARNING
SHOCK HAZARD — Electrical Grounding
Required. Never attempt to repair or perform
maintenance on the unit until the electricity has
been disconnected.
Never remove the round grounding prong from
the plug and never use a two-prong grounding
adapter.
Altering, cutting or removing power cord,
removing power plug, or direct wiring can cause
serious injury, fire, loss of property and/or life,
and will void the warranty.
Never use an extension cord to connect power to
the unit.
Always keep your working area dry.
NOTICE
Electrical installation must observe all state and
local codes. This unit requires connection to a
grounded (three-prong), polarized receptacle
that has been placed by a qualified electrician.
The unit requires a grounded and polarized 115 VAC,
60 Hz, 15A power supply (normal household current). An
individual, properly grounded branch circuit or circuit
breaker is recommended. A GFCI (ground fault circuit
interrupter) is usually not required for fixed location
appliances and is not recommended for your unit because
it could be prone to nuisance tripping. However, be sure
to consult your local codes.
See CUTOUT DIMENSIONS for recommended receptacle
location.
Electrical 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Cutout Dimensions
CUTOUT DIMENSIONS
PREPARE SITE
Your U-Line product has been designed exclusively for a
built-in installation. When built-in, your unit does not
Preferred location
for drain, water
line and receptacle
is in adjacent
5/8"
cabinet.
(16 mm)
require additional air space for top, sides, or rear.
However, the front grille must NOT be obstructed.
The product is designed and manufactured for seamless
integration in the specified cutout opening shown, which
33-7/8"
(860 mm)
to
34-7/8"
(886 mm)
24"
(610 mm)
requires precise measurements. The opening must be
square and plumb front to back. Although not required,
you may choose to increase the overall cutout width for
ease of installation.
17-7/8"
(455 mm)
Metric measurements rounded and optimized.
The Modular 3000 Series units are engineered with a
variety of adjustment features to help ensure a seamless
installation. Adjustable doors, leveling legs and grille will
assist in fine tuning the installation.
All 3000 Series models fully integrate into overlay/face
frame, inset or European/frameless cabinet styles and
install seamlessly into standard 24" (610 mm) depth
cabinet base.
! CAUTION
Unit can NOT be installed behind a closed cabinet
door.
Cutout Dimensions 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Product Dimensions
24" (610 mm)
(Includes 3/4" [20 mm] Integrated Panel)
33-11/16" to 34-11/16"
(856 mm to 881 mm)
3-5/8" to 4-5/8"
(92 mm to 118 mm)
17-3/4"
(450 mm)
Product Dimensions 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Side-by-Side Installation
OTHER SITE REQUIREMENTS
Side-by-Side Installation
Hinge-by-Hinge Installation (Mullion)
When installing two units hinge-by-hinge, 13/16" (22 mm)
is required for integrated models. Additional space may be
needed for any knobs, pulls or handles installed.
Units must operate from separate, properly grounded
electrical receptacles placed according to each unit’s
electrical specifications requirements.
13/16" (22 mm)
Cutout width for a side-by-side installation is the total of
the widths listed under Cutout Dimensions in each unit’s
Installation Guide. Each door can be opened individually
(one at a time) without interference.
Stainless steel models which include the standard stainless
handle will require 4-9/16" (116 mm) to allow both doors
to open to 90° at the same time.
4-9/16" (116 mm)
However, to ensure unobstructed door swing (opening
both doors at the same time), 1/4" (6.4 mm) of space
needs to be maintained between the units.
1/4" (6 mm)
Side-by-Side Installation 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Water Hookup
PREPARE PLUMBING
! CAUTION
Please use the braided stainless steel water supply line
Do not use any plastic water supply line. The line
which comes attached. The water line is fitted with a
is under pressure at all times. Plastic may crack
standard 1/4" (6.35 mm) compression fitting.
or rupture with age and cause damage to your
home.
! WARNING
Do not use tape or joint compound when
attaching a braided flexible water supply line
Prior to installation, determine if this product
that includes a rubber gasket. The gasket
contains a gravity style drain or factory installed
provides an adequate seal – other materials
drain pump. Products without a drain pump may
could cause blockage of the valve.
only use a gravity style drain. Failure to connect
water supply or drain line connections properly
may result in water leakage, personal injury,
and/or property damage. Disconnect power and
turn off water to the unit before attempting to
Failure to follow recommendations and
instructions may result in damage and/or harm,
flooding or void the product warranty.
alter these connections. These connections are
the responsibility of the owner and must be
connected per local plumbing code. If you are
uncertain of how to safely and properly install
this product, contact a licensed plumber.
Water Supply Connection
! CAUTION
Review, obey, and understand the local
plumbing codes before you install your unit.
! CAUTION
Turn off water supply and disconnect electrical
supply to unit prior to installation.
1. Turn off water supply and disconnect electrical supply
to product prior to attempting installation.
2. Locate the desired cold water supply location.
Connect to the cold water supply. The water
pressure should be between 20 and 120 psi (138
3. Locate braided stainless steel
and 827 kPa). The water line MUST have a shut-
water supply line and connect
off valve on the supply line.
to your cold water supply. The
water line should be looped into
2 coils. This will allow the unit
to be removed for cleaning and
servicing. However, make
certain that the tubing is not
pinched or damaged during installation.
Water Hookup 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
4. Turn on water and check for leaks.
5. Route water supply line in cable clamp and secure with
screw.
Water Hookup 2
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Drain
GRAVITY DRAIN
Model numbers including “-00” or “-07” do not include a
factory installed drain pump.
Normal
Proper Drain
Model numbers including “-40” or “-47” include a factory
installed drain pump.
With Trap
Poor Drainage, Water Will Back Up
DRAIN CONNECTION
! CAUTION
With Trap and Vent
Proper Drain
If your U-Line unit did not come with a factory
installed drain pump you must use a gravity
style drain connection. For assistance in
determining if your unit has a pump please
contact U-Line. The floor drain must be large
A gravity drain may be used if:
Drain line has at least a 1" drop per 48" (approximately
2 cm drop per 100 cm) of run.
enough to accommodate drainage from all
attached drains. Follow these guidelines when
Drain line does not create traps and is vented per local
installing drain lines to prevent water from
code.
flowing back into the ice maker storage bin and/
or potentially flowing onto the floor, which may
result in personal injury or property damage.
1. Cut the pre-installed drain tube to length.
2. Connect to your local plumbing per the local code.
NOTICE
Drain can NOT be located directly below the unit.
Unit has a solid base that will not allow the unit
3. If necessary, insulate drain line to prevent
condensation.
to drain below itself.
There is a possibility that hose connections may
! CAUTION
have loosened during shipment.
Failure to connect water supply or drain line
Verify all connections and fittings are free from
leaks.
connections properly can result in personal
injury and property damage. Gravity drain
connections must be routed downward from the
rest of the unit at the rate of 1/4" per foot (1 cm
per 50 cm).
Drain 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
FACTORY INSTALLED DRAIN PUMP
If your drain line will run up to a stand pipe, disposal or
Y-Branch Tailpiece
P60 Pump Required
Air Gap
(Optional Hook-Up)
spigot assembly, or does not otherwise meet the
requirements for a gravity drain, you may have ordered a
pre-installed U-Line P60 drain pump.
Waste
If you need to install a P60 drain pump into your unit, see
6KXW2ɞ
Valve
DRAIN PUMP section in the User Manual.
Hot
Water
See below for typical installations requiring a drain pump.
Cold
Water
NOTICE
Stand Pipe
P60 Pump Required
The maximum lift for the P60 drain pump is
10 feet. This must be done as close to the rear of
the unit as possible.
Waste
6KXW2ɞ
Valve
Hot
Water
Cold
Water
Waste
Disposal Assembly
P60 Pump Required
Air Gap
(Optional Hook-Up)
Waste
Hot
Water
Cold
Water
6KXW2ɞ
Valve
Drain 2
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Drain Pump
NOTICE
PLEASE READ this instruction completely before
attempting to install or operate the unit.
Improper hook-up can result in substantial
property damage! If you are unsure of your
ability to safely connect the drain pump to the
INCLUDED IN KIT:
1. 1x S-shaped Drain Tube
1
2. 1x Straight Drain Tube
(Not used)
2
3. 1x Vent Tube
3
unit, consult a licensed plumber for assistance.
Use these instructions to install the U-Line P60-
4. 1x Braided Discharge Tube
00 drain pump in the U-Line Clear Ice Machine
(Not included in pump kit.
(unit). The drain pump should be installed
Ice Machine ships with
before installing the unit.
discharge tube installed.)
• The U-Line P60-00 drain pump is designed to be used
5. 2x Vent tube Zip Ties
exclusively on the U-Line Clear Ice Machine and is UL
recognized only for use on the U-Line Clear Ice
Machine.
• U-Line Corporation assumes no warranties or
responsibility, whether express or implied, if the P60-00
drain pump is used on another ice machine or product
4
5
6. 2x Small Worm Gear
Clamps
7. 1x Large Worm Gear
6
7
Clamp
for which it is not UL recognized or listed.
9
8. 1x P60 Pump
• Modification of the P60-00 drain pump will void all
warranties.
9. 1x Discharge Tub
(Used on older models only)
NOTICE
Keep your proof of purchase for warranty
purposes.
TOOLS REQUIRED:
• 1/4" x 6" Blade Screwdriver
• Adjustable Pliers
• 1/4" Nut Drive
Drain Pump 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
8
Wiring Plug
Ground Terminal
Discharge Tube Connector
Drain Tube Connector
Vent Tube Connector
Pump Assembly
Note: Slide clamp on hose end before installing hose. Do
not tighten clamp until pump and hoses have been
installed.
4. Install the 3 hoses and hose clamps to the pump
assembly as shown below. Do not tighten clamps at
this time.
INSTALLATION PROCEDURE
! WARNING
Drain Tube
To prevent accidental electrocution, make
certain that the floor surfaces surrounding the
unit are dry whenever power/electricity is
removed from, or applied to the unit.
Vent Tube
Discharge Tube
1. Disconnect your unit from its electrical outlet/socket.
2. Using a screwdriver or 1/4" nut driver, remove the 9
screws from the back panel.
3. Remove the drain line/pipe from the storage bin drain
nipple. Save the clamp for pump installation.
5. Remove the protective paper from the adhesive strip
and carefully set pump inside of unit.
6. Unplug jumper block from ice
machine wiring harness
Jumper
Block
(jumper block has a single
pink wire). Discard jumper
! CAUTION
To prevent damage to the pump, leave sufficient
space between leveling leg and pump.
block.
7. Connect pump wiring plug
to the ice machine wiring
harness connector, where
the jumper block was
Pump Wiring
Plug
removed. The connector is
keyed and can only be
inserted one way.
Drain Pump 2
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
! CAUTION
8. Route the vent tube up
the back of the unit, next
to the insulated tubes.
When working with tools inside of unit, be
Secure vent tube vertical
careful so as not to nick or damage any
to the insulated tubes
refrigerant lines/pipes or wires.
using plastic tie wraps.
! WARNING
9. Connect pump drain tube
to storage bin drain nipple
with clamp removed from
The back panel serves as a guard. Do not put
step 3. Ensure that no
your hands inside the ice machine cabinet or
kinks are present in the
attempt to touch any components except the
tube.
discharge tube during testing.
10.Tighten the clamps on the
! CAUTION
Failure to properly secure the vent tube will
result in water damage to the unit and
surrounding areas. Do not allow vent tube to
kink, bend or be obstructed in any way.
drain, discharge, and vent tubes with a screwdriver or
1/4" nut driver.
Note: The discharge tube will need to be trimmed. Cut
back the tube (MAX of 1/4" on each end) so that no kinks
are formed in drain tube.
! CAUTION
Vent tube must be straight and parallel to
insulated tubes. Do not over-tighten the plastic
tie wraps. Over-tightening can pinch vent tube
closed or cut into insulation.
Drain Pump 3
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Anti-Tip Bracket
SIDE MOUNT
Left Hinged Cabinet
Right Hinged Cabinet
! CAUTION
The anti-tip bracket must be installed to prevent
the unit from tipping when doors are fully
opened or excess weight is placed on the front of
the unit.
The anti-tip bracket has multiple mounting options.
Mounting will depend on your particular cabinet
configuration. Locate 3 #8x5/8" screws included with your
unit.
TOP MOUNT
Side mount position is used when you are unable to mount
the bracket to the underside of your countertop.
1. Remove the pre-installed anti-tip bracket from the top
mount position and align the bracket to the hinge side
of the unit as shown above.
2. Reinstall the 2 #8x5/8" screws into the plate using a
For ease of installation, the anti-tip bracket is pre-installed
#2 Phillips head screwdriver.
in the top mount position.
3. Completely slide the unit into its position in the
1. Completely slide the unit into its position in the
cabinet. Be certain unit height is properly adjusted.
cabinet. Be certain unit height is properly adjusted.
(See GENERAL INSTALLATION).
(See GENERAL INSTALLATION).
4. Open door completely. Make certain door clears
2. Open door completely. Make certain door clears
surrounding cabinetry.
surrounding cabinetry.
5. Using a 3/32" (2.50 mm) drill bit, drill 3 pilot holes 5/8"
3. Using a 3/32" (2.50 mm) drill bit, drill 3 pilot holes 5/8"
(16 mm) deep into bottom of counter top. Use the
(16 mm) deep into cabinetry frame using the anti-tip
bracket as a template.
anti-tip bracket as a template.
6. Install 3 #8x5/8" screws into the plate using a #2
4. Install 3 #8x5/8" screws into the plate using a
Phillips head screwdriver.
#2 Phillips head screwdriver.
Anti-Tip Bracket 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
General Installation
1. Plug in the power/electrical cord.
1. Use a level to confirm
the unit is level. Level
2. Gently push the unit into position. Be careful not to
should be placed along
top edge and side
INSTALLATION
1
entangle the cord or water and drain lines.
edge as shown.
3. Re-check the leveling, from front to back and side to
side. Make any necessary adjustments. The unit’s top
2. If the unit is not level,
surface should be approximately 1/8" (3 mm) below
remove grille and
adjust legs as
2
the countertop.
necessary. Use
included tool to adjust the height of the rear legs.
4. Install the anti-tip bracket.
5. Remove the interior packing material and wipe out the
inside of the unit with a clean, water-dampened cloth.
Rotate Front Legs to Adjust
Rotate Clockwise to raise rear leg.
Rotate Counter-Clockwise to lower leg.
3. Confirm the unit is level after each adjustment and
repeat the previous steps until the unit is level.
INSTALLATION TIP
If the room floor is higher than the floor in the cutout
opening, adjust the rear legs to achieve a total unit rear
height of 1/8" (3 mm) less than the opening’s rear height.
Shorten the unit height in the front by adjusting the front
legs. This allows the unit to be gently tipped into the
opening. Adjust the front legs to level the unit after it is
correctly positioned in the opening.
General Installation 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Integrated Panel Dimensions
Integrated Panel Dimensions
Metric measurements rounded and optimized.
INTEGRATED PANEL
BACK SURFACE MUST HAVE AMPLE FLAT SURFACE
TO MOUNT OVERLAY PANEL FLAT AND WITHOUT
INTERFERENCE
3/4"
(20 mm)
NOTICE
Due to differences in surrounding cabinetry the
17-5/8"
(445 mm)
panel may not perfectly align with door. The
procedure below is designed to provide a
finished integrated panel that seamlessly
integrates with surrounding cabinetry.
Panel Preparation
A full integrated door panel completely covers the door
frame and provides a built-in appearance.
30"
(762 mm)
NOTICE
The door panel must not weigh more than 20 lbs
(10 kg).
It is important to ensure that all drilled holes are
drilled to the correct depth in order to avoid
splits in the wood when hardware is installed.
1. Cut the panels to the dimensions listed in the diagram
Integrated Panel
below.
2. Optional: Stain or finish panel to desired stain or color.
Be sure to closely follow the instructions provided by
the manufacturer.
3. Optional: Install handles and hardware.
NOTICE
When applying an integrated panel to a unit,
ensure that both sides are finished in order to
prevent warping. In some panel installations,
the panel may be visible through the glass while
the door is open.
Integrated Panel Dimensions 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
HANDLELESS INTEGRATED DOOR PANEL
3. Prepare the insert(s) that will back up the handleless
The following procedure is designed to provide a finished,
design. Wooden Insert – Cut 1/8" (3 mm) thick
handleless solid panel for an 18" (450 mm) door that
wooden insert(s) to the dimensions below.
seamlessly integrates with its surrounding cabinetry.
NOTE: Many cabinet manufacturers provide a ready
Wooden insert width
Wooden insert height
17-5/8" (445 mm)
3-1/2" (89 mm)
solution for a handleless, integrated design that can be
easily applied to your U-Line 3000 Series model. Consult
your cabinet manufacturer for applicable design and
installation details. The cabinet manufacturer’s solution to
Wooden Insert
this design and integration detail will often result in an
integrated panel solution wherein the size of the panel
Top Design
and Insert Notch
may result in a height dimension taller than what we
specify. This can be achieved provided the additional
height is positioned above the appliance door.
Main Panel
NOTICE
The integrated panel aligns with the surrounding
cabinetry and, due to differences in cabinetry,
may not align perfectly with the door.
Integrated Panel
The appliance will need up to 34-1/2" (876 mm)
to the underside of the counter to leave room for
leveling adjustments.
4. Optional: Stain or finish panel and wooden insert to
desired stain or color. Be sure to closely follow the
instructions provided by the manufacturer.
A single prepared panel with insert must not
weigh more than 20 lbs (10 kg).
NOTICE
If finishing panel or wooden insert, all sides
Integrated Panel Preparation
must be finished to prevent warping.
1. Cut the main panel to the dimensions below. For
details, see the drawings on the next page.
5. Attach the insert to the panel. Wood glue or equivalent
adhesive should be used to attach insert to panel.
Main panel width
Main panel height
17-5/8" (445 mm)
28-13/16" (732 mm)
2. Create the top design for the handleless feature and
the 1/8" (3 mm) notch for the insert(s) indicated on
the Top Detail drawing, on the next page.
Attach Wooden Insert
Integrated Panel Dimensions 2
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Handleless Integrated Panel Dimensions
1/8" (3 mm)
Top Design
1/4" (6 mm)
7/8" (22 mm)
Ref.
R 5/8"
(R 16 mm)
2-3/8"
(60 mm)
17-5/8"
(445 mm)
2-3/4"
70 mm
Insert Notch
2-3/4"
(70 mm)
Wooden Insert
Notch Depth: 1/8" (3 mm)
Top Detail
28-13/16"
(732 mm)
3/4" (20 mm)
Wooden Insert Dimensions
17-5/8" (445 mm)
1/8" (3 mm)
3-1/2"
(89 mm)
Integrated Panel Dimensions 3
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
EXTENDED INTEGRATED PANEL
NOTICE
Due to differences in surrounding cabinetry the
panel may not perfectly align with door. The
procedure below is designed to provide a
finished panel that seamlessly integrates with
surrounding cabinetry.
Panel Preparation
An extended integrated panel can be used to maintain
alignment with an adjacent extended cabinet height or a
reduced toe-kick/grille application.
1. Cut the panels to the dimensions listed in the
appropriate diagram on the next page.
2. Optional: Stain or finish panel to desired stain or color.
Be sure to closely follow the instructions provided by
the manufacturer.
3. Optional: Install handles and hardware.
NOTICE
The door panel must not weigh more than 20 lbs
(10 kg).
It is important to ensure that all drilled holes are
drilled to the correct depth in order to avoid
splits in the wood when hardware is installed.
Appliance will need up to 34-1/2" (876 mm) to
the underside of the counter to leave room for
leveling adjustments.
When applying an integrated panel to a unit,
ensure that both sides are finished in order to
prevent warping. In some installations, the
panel may be visible through the glass while the
door is open.
Integrated Panel Dimensions 4
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Front
Side
Integrated Panel/Integrated Frame
Integrated Panel
U-Line
Unit
Cabinet
U-Line
Unit
3-5/16" (89 mm)
to
4-5/16" (114 mm)
> 3-5/16"
(> 89 mm)
3-5/16" (89 mm)
to
4-5/16" (114 mm)
Floor
Front
Side
Extended Integrated Panel/Extended Integrated Frame
U-Line
Unit
Cabinet
Integrated Panel
U-Line
Unit
* Panel can extend beyond the door frame.
** A minimum of 1" (25 mm) from the floor
is required for proper ventilation.
*
3-5/16" (89 mm)
to
1" (25 mm)**
3-5/16" (89 mm)
to
1" (25 mm)**
Floor
Integrated Panel Dimensions 5
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Extended Integrated Panel Dimensions
BACK SURFACE MUST HAVE AMPLE FLAT SURFACE
TO MOUNT INTEGRATED PANEL FLAT AND
3/4"
WITHOUT INTERFERENCE
(20 mm)
17-5/8"
(445 mm)
30.0" 33-7/8"
(762 mm 860 mm)*
Integrated Panel
* A minimum of 1" (25 mm) is required from the
floor to the bottom of the extended integrated
panel/frame for proper ventilation.
Integrated Panel Dimensions 6
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
INTEGRATED GRILLE (PLINTH STRIP/BASE
FASCIA) DIMENSIONS
3-5/16" to 4-5/16"
(84 mm to 110 mm)
Integrated Grille - Plinth
Dimensions
PREPARE AND INSTALL INTEGRATED GRILLE
(PLINTH STRIP/BASE FASCIA)
panel. Recommended panel thickness is between 1/4"
(6 mm) and 3/8" (9 mm). Height will vary from 3-5/16"
1" (25 mm)
shape your integrated grille (plinth strip/base fascia)
1-9/16"
(40 mm)
1. Use the dimensions provided in the diagram to cut and
(84 mm) to 4-5/16" (110 mm) based on your grille
(plinth strip/base fascia) height.
front, back and edges to prevent warping. Carefully
follow the manufacturer’s recommendations for finish
17-7/8"
(455 mm)
panel to match your surrounding furniture. Finish
14-3/4”
(375 mm)
2. Finish or stain your grille (plinth strip/base fascia)
application and cure times.
3. Apply double sided tape to the backside of the
integrated grill (plinth strip/base fascia). Use the
3M™ VHB™ tape, a high strength bonding tape.
1-9/16"
(40 mm)
diagram below for reference. U-Line recommends
Apply Tape To Shaded Area
4. Remove backing paper from double sided tape.
5. Carefully align grille (plinth strip/base fascia) over
integrated panel and press into position.
Integrated Grille - Plinth Dimensions 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Integrated Panel Installation
1. Fully open door.
NOTICE
It is important to ensure that all drilled holes are
drilled to the correct depth in order to avoid
splits in the wood when hardwood is installed.
2. Starting at corner, pull
gasket away from door.
8. Locate 6 of the #6x 1-1/2" (38 mm) screws provided
with your unit.
3. Continue to pull gasket
free from gasket channel.
9. Using a Phillips screwdriver, place one screw into each
4. Upon removal, lay gasket down on a flat surface.
5. Align top of panel with top edge of door. Center panel
on door. (For 3036/3090 models, align panel on the
hinge side-edge of door.)
of the 6 pilot holes and screw down. Do not overtighten
screws.
10.Ensure the screws sit flush against the bottom of the
channel.
NOTICE
Due to differences in floor construction or
surrounding cabinetry, the panel may not sit
flush with the top of the door.
6. Secure integrated
panel to door using
Integrated Panel
Integrated Panel
11.Remove clamps from door.
Bar
Clamp
clamps. A robust
NOTICE
tape may also be
used. U-Line
If panel requires additional adjustment after
recommends the
removing clamps, slightly loosen each screw and
use of bar clamps
to secure the panel
to the door. If using
tape, be certain the
adjust panel as necessary. Tighten screws upon
Door/Drawer
Wood
Panel
tape will not
fully seated.
upon removal.
(3 mm) drill bit, drill
12.Starting at the corners, re-install the gasket into the
gasket channel in the frame. Make sure the gasket is
damage panel finish
7. Using a 7/64"
completion.
Bar
Clamp
6 pilot holes into
the wood panel 1/2"
(12 mm) deep using
the holes in the door
frame as a guide.
Integrated Panel Installation 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Grille - Plinth Installation
Installing the grille
(plinth strip/base fascia)
REMOVING AND INSTALLING GRILLE
(PLINTH STRIP/BASE FASCIA)
1. Align slots in grille (plinth strip/base fascia) rail with
! WARNING
Disconnect electrical current to the unit before
removing the grille (plinth strip/base fascia).
When using the unit, the grille (plinth strip/base
fascia) must be installed.
screw heads in base of unit
2. Push grille (plinth strip/base fascia) rails towards the
center of the unit and set rails over screw head.
3. Slide grille (plinth strip/base fascia) into position. Using
included 7/64" Allen wrench tighten grille (plinth strip/
base fascia) lock screws.
Edges of sheet metal may be sharp.
Removing the grille
(plinth strip/base fascia)
1. Disconnect electrical current to unit.
ADJUSTING GRILLE
(PLINTH STRIP/BASE FASCIA)
2. Using the included 7/64" Allen wrench, loosen (but do
not remove) both grille (plinth strip/base fascia) lock
screws. See below.
The grille (plinth strip/base fascia) has an automatic
vertical plane adjustment and can also be adjusted on its
horizontal plane as well. To adjust your grille (plinth strip/
base fascia) to match your surrounding furniture, follow
the instructions below.
Grille Mounting
Screws
Grille
Skirt
3. Gently pull grille (plinth strip/base fascia) away from
unit until it stops.
1. Loosen, but do not remove, the lock screws on the
inside of the grille (plinth strip/base fascia) rails. Lock
4. Push grille (plinth strip/base fascia) rails towards the
center of the unit to lift rails off lock screws.
screws are located on the inside of each grille (plinth
strip/base fascia) rail.
2. The grille (plinth strip/base fascia) can be extended
horizontally by pulling out a maximum of 1-1/2"
(38 mm). Do not exceed 1-1/2" (38 mm). Secure the
lock screws after adjusting.
Grille Rail
3. The grille (plinth strip/base fascia) skirt may be
manually adjusted to the height of your floor. Simply
5. Pull grille (plinth strip/base fascia) free from unit.
raise or lower the skirt as needed.
Grille - Plinth Installation 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Door Swing
For models that are installed adjacent to a wall, 1/4"
(6 mm) clearance is recommended from wall on hinge side
to allow the door to open 90°. Allow for additional space
for any knobs or pulls installed on the integrated panel/
frame.
Units have a zero clearance when installed adjacent to
cabinets.
Wall
1/4" (6 mm)
90°
Door Swing
Space Required
For any Knobs or Pulls
Door Swing 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Door Stop
3. Once cover is removed, slide hinge pin into hole as
shown. Pin should slide into place, stopping the door at
Your U-Line unit was shipped to you with the optional 90°
90°; if the pin does not go into the hole shown, hold
pin.
the door less than 90° open and try again.
Your unit’s door(s) will open 115° straight from the
factory. If you would like the door stop at 90° follow these
instructions.
NOTICE
If your unit is already undercounter, it will need
to be moved out to access the hinge. With the
90° stop pin in place, you will not be able to
replace the hinge cover.
1. Open door approximately 90°.
4. To fully seat the pin, tap it lightly with a hammer.
5. Carefully slide your unit back in place.
NOTICE
The pin can be removed to return the door swing
back to its original 115° swing by tapping the pin
out from the bottom of the hinge.
2. Remove hinge cover by lifting top and bottom of hinge
CLOSER
cover and sliding the cover inwards to remove from
The door hinge has a self-closing feature that engages
hinge.
when the door is open approximately 6" (150 mm) (about
25°).
1
3
2
Door Stop 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Door Adjustments
DOOR ALIGNMENT AND ADJUSTMENT
Align and adjust the door if it is not level or is not sealing
properly. If the door is not sealed, the unit may not cool
T-25 Torx Screw
properly, or excessive frost or condensation may form in
the interior.
NOTICE
Properly aligned, the door’s gasket should be
firmly in contact with the cabinet all the way
T-25 Torx Screw
around the door (no gaps). Carefully examine
the door’s gasket to ensure that it is firmly in
contact with the cabinet. Also make sure the
door gasket is not pinched on the hinge side of
the door.
REVERSING THE DOOR
1. Open door.
! CAUTION
Do not attempt to use the door to raise or pivot
2. Remove top hinge cover by lifting top and bottom flaps
and slide inwards. Repeat on bottom hinge.
your unit. This would put excessive stress on the
hinge system.
Alignment and Adjustment Procedure
1. Open door and remove gasket near the hinges.
2. Using a T-25 Torx Bit, loosen each pair of Torx head
screws on both the upper and lower hinge plates.
3. Square and align door as necessary.
4. Tighten Torx head screws on hinge.
5. Reinstall gasket into the channel starting at the corner.
Door Adjustments 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
3. Using T-25 Torx bit loosen screw #1 and remove screw
#2 on top and bottom hinge. Slide and remove the
door from unit. Completely remove screw #1 on top
and bottom.
2
1
4. Remove caps from screw heads on opposite side (2 on
top and 2 on bottom). Using #2 Phillips bit remove the
4 underlying screws. Reinstall the screws and caps on
the opposite side.
5. Partially install screw #1 in the outer most holes on top
and bottom. Rotate door 180°, align hinge over screw
#1 and slide/seat into position. Reinstall screw #2 on
top and bottom. Tighten both screws and install hinge
cover.
Align and adjust the door:
Align and adjust the door (see DOOR ALIGNMENT AND
ADJUSTMENT).
Door Adjustments 2
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
First Use
All U-Line controls are preset at the factory. Initial startup
requires no adjustments.
NOTICE
U-Line recommends discarding the ice produced
during the first two to three hours of operation
to avoid possible dirt or scale that may dislodge
from the water line.
When plugged in, the unit will begin operating under the
factory default setting. Follow the on screen prompt for
language selection and temperature units.
To turn the unit off, press
and hold for 5 seconds and
release. The display will show a countdown to switching the
unit off.
To power your unit on, simply press
and the unit will
immediately switch on.
First Use 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Control Operation
Zone Toggle
Up
Select
ICE PRODUCTION
Power
U-Select Lighting
Down
CONTROL FUNCTION GUIDE
FUNCTION
COMMAND
DISPLAY/OPTIONS
OFF
Press
and hold
Display will count down from 5 to off.
ON
Press
and release
Unit will come on immediately.
Adjust lighting
Press
to adjust lighting
Press
or
to set low, medium or high.
Customer menu
Press
and hold for 5 seconds
Press
or
to scroll through menu.
Service menu
Press
or
Press
or
to scroll through menu.
and hold for 5 seconds
U-SELECT® CONTROL
2. Press
Digital Display
or
to cycle through each available
brightness setting (Low, Medium or High).
The 3000 Series units are controlled by a feature rich,
advanced OLED display control unit. The control panel
allows adjustment to temperature set point, access to
Energy Saver Mode, internal temperature readings, and
many other features.
U-Select Lighting
3. Press
to cycle through each available timer setting.
Selections include “On With Door”, “On 3 Hours”, “On 6
Hours”, or “On 24 Hours”.
4. To exit, press
or simply wait for the menu to time
out.
Up
Select
CUSTOMER MENU
The 3000 Series of U-Line undercounter refrigeration
appliances contains a feature rich customer menu. The
Down
Power
U-Select Lighting
Customer Menu allows access to a series of advanced
features including Energy Saver Mode, Sabbath Mode,
actual temperature readings as well as a method to
1. To begin, press
to enter the lighting menu.
restore factory defaults.
Control Operation 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Energy Saver Mode
3000 Series - Customer Menu
Up
Up
Energy Saver Mode
Indicator
Select
WELCOME TO THE
CUSTOMER MENU. USE
UP/DOWN ARROWS TO
SCROLL SETTINGS.
Select
ICE PRODUCTION
(12m remaining)
Down
Down
1. To access the Customer Menu hold
for 5 seconds.
Energy Saver mode reduces overall energy consumption
by reducing the amount of ice stored in the bin, along with
decreasing the lighting.
2. Press
or
to scroll through available selections.
1. To enter Energy Saver Mode, first select Energy Saver
3. Press
from the Customer Menu.
to enter selected sub-menu.
4. To exit Customer Menu, press
bottom of the display and press
to scroll to the
2. Press
to select “Off” in the menu.
to select “Exit”.
3. Press
.
Actual Temps
Up
Select
RETURN TO MENU
ACTUAL TEMPS
BIN TEMP = 1.6
COND TEMP = 45.5
4. Press
or
to change the selection from Off to On.
5. Press
to confirm your selection.
Can be displayed in Celsius
6. To return to the Customer Menu, press
Down
The Actual Temps option displays the actual temperature
and select
“Return to Menu”.
of the ice bin and condenser, as well as ambient
temperature.
7. To cancel Energy Saver Mode simply return to the
Customer Menu, select Energy Saver and change “On”
1. To view actual temperature, press
and select
to “Off”.
“Actual Temps” from the Customer Menu.
2. Press
or
to scroll through available information.
3. To return to the Customer Menu, press
and select
“Return to Menu”.
Control Operation 2
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Languages
2. Press
. The current setting will begin to flash.
Up
Select
RETURN TO MENU
LANGUAGES
ENGLISH
3. Press
or
to select a different level.
4. Press
to confirm your choice.
Down
The U-Line 3000 Series of models supports a number of
display languages including English, Spanish, French,
Fahrenheit / Celsius
Up
Select
German and Italian.
RETURN TO MENU
FARENHEIT/CELSIUS
DEGREES = °F
1. To change display language select Languages from the
Customer Menu.
Down
2. Press
Temperature and set point information can be displayed in
to select “English”.
either Fahrenheit or Celsius.
3. Press
. “English” will begin to flash.
To change from Fahrenheit to Celsius enter the
Fahrenheit / Celsius Menu from within the Customer
4. Press
or
to cycle through the available
Menu.
languages.
1. Press
5. Press
to select “Degrees”.
to confirm your choice.
2. Press
Sound Level
3. Press
Up
Select
RETURN TO MENU
SOUND LEVEL
HIGH
. The selection will begin to flash.
or
to select between °F (Fahrenheit) or °C
(Celsius).
4. Press
to confirm your choice.
Down
Audible alarms and alert tones support four different
Sound Level settings, High, Medium, Low, and Off.
To select a new tone level, enter the Sound Level Menu
from the Customer Menu.
1. Press
or
to select the current sound level.
Control Operation 3
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
To activate Silent Mode:
Clean Cycle
Up
Select
RETURN TO MENU
CLEAN CYCLE
CLEAN?
1. Press
2. Press
to select “Silence?”.
. Silent Mode will now begin.
To cancel Silent Mode:
Down
A clean cycle can be initiated through this menu. Once the
cleaning cycle starts, the cycle cannot be stopped until
1. Press
to select “Cancel?”.
2. Press
. Silent Mode will end.
complete.
To initiate a clean cycle, select “Clean Cycle” from the
Customer Menu. Please refer to CLEANING section
regarding proper cleaning procedure.
Ice Adjust
Up
Select
1. Press
to select “Clean Cycle”.
RETURN TO MENU
ICE ADJUST
ICE ADJUST = 0
2. Press
. The clean cycle will now begin.
Down
3. Refer to CLEANING section regarding proper cleaning
procedure.
The Ice Adjust option adjusts ice thickness by adding or
subtracting up to 5 minutes of ice production.
Silent Mode
Up
Select
To change the ice thickness, enter the Ice Adjust Menu
from within the Customer Menu.
RETURN TO MENU
SILENT MODE
SILENCE?
To adjust thickness:
1. Press
to select “Ice Adjust”.
Down
Users can halt ice production for 3 hours with an option
2. Press
. The selection will begin to flash.
called “Silent Mode” in the Customer Menu. Silent Mode
will begin once the current ice making cycle is complete.
After 3 hours in Silent Mode, normal ice production will
continue.
NOTE: Silent Mode will not silence any alerts.
3. Press
to make the ice thicker or
to make the ice
thinner.
4. Press
to confirm your choice.
To initiate Silent Mode, enter Silent Mode Menu from
within the Customer Menu.
Control Operation 4
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Help
Up
Select
RETURN TO MENU
Help
Model 3018CLR
1-800-779-2547
Down
To access the Help Menu, select “Help” from the Customer
Menu. Press
or
to scroll through available
information.
To return to the Customer Menu, press
“Return to Menu” and press
to select
to confirm.
Control Operation 5
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Ice
Your clear ice machine is pre-set to produce ice between
the optimal dimensions illustrated below:
ICE CUBE THICKNESS ADJUSTMENT
Cube Types
NOTICE
Ice thickness adjustment should only be made
1/4" TO 1/2"
(6.4 mm to 12.7 mm)
DIMPLE
1/16" TO 1/8"
(1.6 mm to 3.2 mm)
ICE BRIDGE
one increment at a time. Allow ice maker
production to stabilize for 24 hours before
rechecking ice thickness.
Remove all ice from the storage bin.
Ice cubes in any given batch will vary, so it is necessary
to choose cubes from the sample area for comparison
when making adjustments.
THIN BRIDGE
The ice cube thickness is factory set for best overall
DEEP DIMPLE
THICK BRIDGE
LITTLE OR
NO DIMPLE
performance. The factory setting “0” is designed to
maintain an ice bridge of approximately 1/16" to 1/8"
(1.6 mm to 3.2 mm) under normal conditions, resulting in
a dimple of approximately 1/4" to 1/2" (6.4 mm to
12.7 mm) in depth. A fuller cube with less of a dimple
results in a thicker ice bridge. As the ice bridge thickens,
the tendency for the cubes to stay together as a slab
increases. A bridge thicker than 1/8" (3.2 mm) may cause
cubes to overfill the ice bucket.
DIMPLES
ICE BRIDGE
Ice Bridge and Dimples
Ice 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
ICE ADJUST
Up
Select
RETURN TO MENU
ICE ADJUST
ICE ADJUST = 0
Down
Adjust ice thickness as follows:
1. Press
and
and hold for 5 seconds to enter the
Customer Menu.
2. Press
3. Press
4. Press
to select “Ice Adjust”.
. The selection will begin to flash.
to make the ice thicker or
thinner. Press
to make the ice
to confirm your choice.
The total range of adjustment is -5 (thinest) to +5
(thickest). If further adjustments are desired, repeat
Steps 1 through 4.
Ice 2
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
L
Sabbath Mode
1
2
3
4
5
6
7
Up
Select
Down
U-Line Clear Ice Machine models are Star-K certified and
can be used during the Sabbath. View a full list of Star-K
certified U-Line units at www.star-k.org.
To prepare the unit for the Sabbath:
1. Press
and hold the until the unit turns off.
2. No new ice will form when the unit is off, but previously
made ice will still be accessible/present for over 24
hours. Pump equipped models will continue to remove
water as needed even if the unit is off.
Sabbath Mode remains active until
is pressed again
and the unit turns on.
Sabbath Mode 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Airflow and Product Loading
NOTICE
The unit requires proper airflow to perform at its
highest efficiency. Do not block the front grille at
any time, or the unit will not perform as
expected. Do not install the unit behind a door.
Airflow and Product Loading 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Cleaning
EXTERIOR CLEANING
Integrated Models
To clean integrated panels, use household cleaner per the
cabinet manufacturer’s recommendations.
Stainless Models
Stainless door panels and handles can discolor when
exposed to chlorine gas, pool chemicals, saltwater or
cleaners with bleach.
Keep your stainless unit looking new by cleaning with a
good quality all-in-one stainless steel cleaner and polish
monthly. For best results use Claire® Stainless Steel
INTERIOR CLEANING
Disconnect electric current to the unit.
Clean the interior and all removed components using a
mild nonabrasive detergent and warm water solution
applied with a soft sponge or non-abrasive cloth.
Polish and Cleaner. Comparable products are acceptable.
Frequent cleaning will remove surface contamination that
Rinse the interior using a soft sponge and clean water.
could lead to rust. Some installations may require cleaning
weekly.
Do not use any solvent-based or abrasive
cleaners. These types of cleaners may transfer taste to
Do not clean with steel wool pads.
the interior products and damage or discolor the lining.
Do not use stainless steel cleaners or polishes on
any glass surfaces.
CLEAR ICE MAKER CLEANING CYCLE
The 3000 series ice maker is equipped with an automatic
clean alert function. Cleaning cycles should be run as
Clean any glass surfaces with a non-chlorine glass
notified. Otherwise, to maintain operational efficiency, the
cleaner.
unit should be cleaned every three months. Depending on
water conditions, more frequent cleaning may be
Do not use cleaners not specifically intended for
stainless steel on stainless surfaces (this
includes glass, tile and counter cleaners).
If any surface discoloring or rusting appears, clean it
quickly with Bon-Ami® or Barkeepers Friend Cleanser® and
necessary. If the ice maker requires more frequent
cleaning, consult a plumber to test the water quality and
recommend appropriate treatment.
! CAUTION
a nonabrasive cloth. Always clean with the grain. Always
finish with Claire® Stainless Steel Polish and Cleaner or
Wear rubber gloves and safety goggles and/or
comparable product to prevent further problems.
face shield when handling Ice Machine Cleaner.
Using abrasive pads such as ScotchBrite™ will
cause the graining in the stainless steel to
become blurred.
NOTICE
Rust not cleaned up promptly can penetrate the
surface of the stainless steel and complete
removal of the rust may not be possible.
Discard all ice produced in the first harvest.
Should electricity to the unit be interrupted
during the self-clean cycle, the complete
cleaning cycle will repeat after electricity is
restored.
Cleaning 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Use only U-Line Ice Machine Cleaner (Part No.
5. Re-install the standpipe into the water trough.
37050), available from your dealer or direct from
your local parts distributor. To locate a parts
distributor near you, visit www.u-line.com. It is
a violation of federal law to use this solution in a
manner inconsistent with its labeling. Use of any
Evaporator
other cleaner can ruin the finish of the
evaporator and will void the warranty. Read and
understand all labels printed on the package
before use.
Standpipe
Water trough
U-Line Ice Machine Cleaner is used to remove lime scale
and other mineral deposits. Refer to the following steps to
6. Clean the Interior Bin as follows:
initiate the self-cleaning cycle.
• Dilute one packet of CLR cleaner into two quarts of
water.
! CAUTION
Never use anything to force ice from the
evaporator. Damage may result.
1. Switch the ice maker
off and allow any ice
Evaporator cover
to melt off of the
• Using a sponge or cloth, clean interior of ice bin,
tubing and door. This cleaner will remove all mineral
deposits and other contaminants from the surfaces.
• Using a bottle brush, clean out the trough drain tube
and pump tubing where needed.
evaporator.
2. Remove all ice from
the storage bin.
Brush
3. Remove evaporator
cover.
4. Remove the standpipe by lifting it up while using a
slight back and forth motion to loosen it from the drain
hole. The water in the reservoir will flow down the
drain.
7. Switch on unit on by pressing
.
8. Place unit in cleaning mode. See CONTROL
OPERATION for more detail.
Cleaning 2
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
9. When water begins flowing over the evaporator
(approximately 3 minutes), pour 1 packet of CLR
cleaner into the water trough. The cleaning process will
last approximately 45 minutes.
10.Dilute 1 tablespoon (15 ml) bleach in 1 gallon
(3.8 liters) of warm water. Apply this solution to the
entire inside of the storage area. Then rinse thoroughly
with water.
The unit will resume operation approximately 15 minutes
after the automated cleaning process is completed. The
water fill valve will energize, fill the water reservoir, and
shut-off after three minutes. The compressor begins to
operate and water flows over the evaporator assembly (ice
mold). Initially, the water flow may not be uniform,
causing uneven sized cubes or water to spill into the ice
storage bin. This is a normal situation that will correct
itself within the first 24 hours of operation.
NOTICE
Discard all ice produced in the first harvest.
Should power to the unit be interrupted during
the self-clean cycle, the complete cleaning cycle
will repeat after power is restored.
REFRESH KIT
Due to variations in water quality or inadequate
maintenance your unit may become excessively coated in
lime scale or calcium. U-Line offers a cost effective
refresh kit which replaces many interior components and
will return your unit to like new condition. Refresh kits
may be ordered from your local distributor and installed
by your local service company. For information on your
local distributor or service company please visit
www.u-line.com.
Cleaning 3
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Cleaning Condenser
INTERVAL - EVERY SIX MONTHS
To maintain operational efficiency, keep the front grille
(plinth strip/base fascia) free of dust and lint, and clean
the condenser when necessary. Depending on
environmental conditions, more or less frequent cleaning
may be necessary.
! WARNING
Disconnect electric current to the unit before
cleaning the condenser.
NOTICE
DO NOT use any type of cleaner on the
condenser unit. Condenser may be cleaned using
a vacuum, soft brush or compressed air.
1. Remove the grille (plinth strip/base fascia). (See
GRILLE-PLINTH INSTALLATION).
2. Clean the condenser coil using a soft brush or vacuum
cleaner.
3. Install the grille (plinth strip/base fascia).
Condenser
Cleaning Condenser 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Extended Non-Use
VACATION/HOLIDAY, PROLONGED SHUTDOWN
For questions regarding winterization, please
The following steps are recommended for periods of
call U-Line at +1.800.779.2547.
extended non-use:
1. Remove all consumable content from the unit.
2. Disconnect the power cord from its outlet/socket and
leave it disconnected until the unit is returned to
service.
! CAUTION
Damage caused by freezing temperatures is not
covered by the warranty.
Do not put anti-freeze in your unit.
3. Turn off the water supply.
4. If ice is on the evaporator, allow ice to thaw naturally.
5. Clean and dry the interior of the cabinet. Ensure all
water has been removed from the unit.
6. Disconnect the water and drain line (if applicable)
making sure all water is removed from the lines.
7. The door must remain open to prevent formation of
mold and mildew. Open door a minimum of 2"
(50 mm) to provide the necessary ventilation.
WINTERIZATION
If the unit will be exposed to temperatures of 40°F (5°C)
or less, the steps above must be followed. In addition, P60
drain pumps in clear ice machines must be drained
according to the following procedure:
1. Remove the drain pump from the ice machine.
2. Drain the water in the pump’s reservoir by turning the
pump upside down and allowing the water to drain
through the pump’s inlet and vent tube fittings.
3. After water is drained, reinstall the drain pump and
reattach all connections.
Extended Non-Use 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Troubleshooting
• Compressor: The compressor makes a hum or pulsing
sound that may be heard when it operates.
BEFORE CALLING FOR SERVICE
If you think your U-Line product is malfunctioning, read
the CONTROL OPERATION section to clearly understand
the function of the control.
If the problem persists, read the NORMAL OPERATING
SOUNDS and TROUBLESHOOTING GUIDE sections below
to help you quickly identify common problems and
possible causes and remedies. Most often, this will resolve
the problem without the need to call for service.
IF SERVICE IS REQUIRED
If you do not understand a troubleshooting remedy, or
your product needs service, contact U-Line Corporation
directly at +1.800.779.2547.
When you call, you will need your product Model and
Serial Numbers. This information appears on the Model
and Serial number plate located on the interior of your
product or can be accessed through “Help” in the
• Evaporator: Refrigerant flowing through an evaporator
may sound like boiling liquid.
• Condenser Fan: Air moving through a condenser may
be heard.
• Solenoid Valves: An occasional clicking sound may be
heard as solenoid valves are operated.
TROUBLESHOOTING GUIDE
! DANGER
ELECTROCUTION HAZARD. Never attempt to
repair or perform maintenance on the unit
before disconnecting the main electrical power.
Troubleshooting - What to check when problems occur:
Customer Menu.
Problem
Possible Cause and Remedy
Digital Display
and Light Do
Not Work.
Ensure power is connected to the unit.
If the unit is cooling, it may be in Sabbath
mode.
Interior Light
Does Not
Illuminate.
If the unit is cooling, it may be in Sabbath
mode or manually set to off.
Lighting may be set to on; reset to with door.
unfamiliar.
Light Remains
on When Door
Is Closed.
Normal operating sounds may be more noticeable because
Unit Develops
Condensation
on External
Surfaces.
The unit is exposed to excessive humidity.
Moisture will dissipate as humidity levels
decrease.
tendency to reflect normal appliance operating noises.
Digital Display
Functions, But
Unit Does Not
Produce Ice.
Ensure the unit is not in “Showroom Mode.”
Momentarily unplug or interrupt power supply
to the unit.
Listed below are common refrigeration components with a
Digital Display
Shows an
Error.
“Door” indicates the door may be opened too
long. Ensure the door is closing properly. For
other error codes contact U-Line Customer
Service.
Ice Is Too
Thick/Thin
Ice Adjust not set to user’s preference. Adjust
ice thickness via Customer Menu.
NORMAL OPERATING SOUNDS
All models incorporate rigid foam insulated cabinets to
provide high thermal efficiency and maximum sound
reduction for its internal working components. Despite this
technology, your model may make sounds that are
of the unit’s environment. Hard surfaces such as cabinets,
wood, vinyl or tiled floors and paneled walls have a
brief description of the normal operating sounds they
make. NOTE: Your product may not contain all the
components listed.
Poor Ice Quality Unit may not be level. Check if unit is level.
Ice maker may be dirty. Clean ice maker.
Troubleshooting 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
Problem
Possible Cause and Remedy
No Ice
Production
Ensure water is being supplied to the unit.
Verify the ice making unit is turned on.
Not Enough Ice Ensure the condenser coil is clean and free of
any dirt or lint buildup.
Water in Bin
Ensure the unit is plugged in. Check if the
drain is restricted. Ensure drain is free of
foreign debris and hose is not kinked or
twisted.
Hear Running
Water
During ice creation, the water running over the
evaporator may be heard.
Hear Ice Falling After each harvest, ice will fall into the bin.
ERROR NOTIFICATION
The 3000 model series continuously monitors a series of
inputs and parameters to ensure proper and efficient
operation of your unit. Should the system detect a fault, an
error notification will be displayed on the user interface.
See below for a list of errors.
ID
Description
Solution
No Comm
Unit lost
communication to
the display.
Disconnect and
reconnect power to
unit. Contact Customer
Care if persistent.
Zone T Open
Left or right zone
thermistor circuit
open.
Contact Customer
Care.
Amb Thrm Open Ambient thermistor
circuit open.
Contact Customer
Care.
Zone T Short
Contact Customer
Care.
Left or right zone
thermistor circuit
shorted.
Troubleshooting 2
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
U-Line Corporation | Limited Warranty
1. U-Line Corporation (“U-Line”) warrants each U-Line
product to be free from defects in materials and
workmanship for a period of one year (two years on
Modular 3000 Series) from the date of installation. ULine further warrants the sealed system (consisting of
the compressor, condenser, evaporator, hot gas
bypass valve, dryer, and connecting tube) in each ULine product to be free from defects in materials and
workmanship for a period of five years from the date of
installation.
4. The following conditions are excluded from this limited
warranty: use of cleaners other than the recommended
stainless steel cleaners and U-Line Clear Ice Maker
cleaner; installation charges; damages caused by
disasters or acts of God, such as fire, floods, wind and
lightning; damages incurred or resulting from shipping,
improper installation, unauthorized modification, or
misuse/abuse of the product; customer education
calls; food loss and spoilage; door and water level
adjustments (except during the first 30 days from the
date of installation); defrosting the product; adjusting
the controls; door reversal; and cleaning the
condenser.
2. During the initial one year warranty period (two years
on Modular 3000 Series) for all U-Line products U-Line
shall: (1) repair any product or replace any part of a
product; and (2) for all Marine, RV and Domestic ULine products sold and serviced in the United States
(including Alaska and Hawaii) and Canada, U-Line shall
be responsible for the labor costs performed by a ULine authorized service company, incurred in
connection with the replacement of any defective part.
During years two through five of the warranty period
for the sealed system, U-Line shall: (1) at U-Line’s
option repair or replace any part of the sealed system;
and (2) for all Marine, RV and Domestic U-Line
products sold and serviced in the United States
(including Alaska and Hawaii) and Canada, U-Line shall
be responsible for the labor costs incurred in
connection with the replacement of any defective part
of the sealed system. All other charges, including
transportation charges for replacements under this
warranty and labor costs not specifically covered by
this warranty, shall be the responsibility of the
purchaser. This warranty extends only to the original
purchaser of the U-Line product. The Product
Registration Card included with the product should be
promptly completed by you and mailed back to U-Line
or you can register on-line at www.u-line.com.
3. The warranty listed above does not apply to floor
display models. The warranty for these models shall be
one year from the date of installation. This one-year
warranty does not apply to cosmetic damages; proof of
purchase may be required.
5. U-Line products are designed to operate in ambient
temperatures between 50°F and 100°F unless
otherwise noted in the product manual. Exposure to
temperatures outside this range may cause
degradation of performance and issues such as lower
ice production or spoiled contents are not covered
under the terms of this warranty as a result of that
exposure. U-Line product may not be subjected to
temperatures below 40°F without following the
winterization and vacation shutdown procedures in
your product manual.
6. U-Line’s Outdoor Limited Warranty, set forth in this
Paragraph 6, shall apply to U-Line models deemed
suitable for outdoor use by Underwriters Laboratory
(“UL”) as noted in the U-Line Product Catalog, U-Line’s
website and/or on the serial tag located inside the
product. Outdoor product may come into contact with
rain by virtue of outdoor use. Exposure to other
sources of water shall also cause this warranty to be
void, including flooding of the area in proximity of the
unit greater than 1/8" deep in water, hurricanes,
splashing of pool water, or directing a spray from a
hose or similar device into and around the unit.
7. If a product defect is discovered during the applicable
warranty period, you must promptly notify U-Line at 1800-779-2547 or the dealer from whom you purchased
the product. In no event shall such notification be
received later than 30 days after the expiration of the
applicable warranty period. U-Line may require that
Warranty 1
USER GUIDE
u-line.com
SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE
defective parts be returned, at your expense, to ULine’s factory in Milwaukee, Wisconsin, for inspection.
Any action by you for breach of warranty must be
commenced within one year after the applicable
warranty period.
8. THIS LIMITED WARRANTY IS IN LIEU OF ANY AND ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR IMPLIED WARRANTY OF
FITNESS FOR A PARTICULAR PURPOSE, ALL OF WHICH
ARE DISCLAIMED. U-Line’s sole liability and your
exclusive remedy under this warranty are set forth in
the paragraphs above. U-Line shall have no liability
whatsoever for any incidental, consequential or special
damages arising from the sale, use or installation of
the product or from any other cause whatsoever
whether based on warranty (express or implied) or
otherwise based on contract, tort or any other theory
of liability.
9. Some states do not allow limitations on how long an
implied warranty lasts or the exclusion or limitation of
incidental or consequential damages, so the above
limitations may not apply to you. This warranty gives
you specific legal rights, and you may also have other
rights which vary from state to state.
10.Copyright © 2014 U-Line Corporation. All Rights
Reserved. | Publication Number 30379 | 03/2016 Rev. I
Warranty 2
Download PDF

advertising