Frigidaire | DGHX2355TF | Use and Care | Frigidaire DGHX2355TF Use and Care

All about the
Use & Care
of your
Refrigerator
TA B L E O F C O N T E N T S
Storage Features.......................................18
Features at a Glance....................................4
Automatic Ice & Water Dispenser...............20
Installation.................................................5
Changing the Filter....................................26
Door Removal Instructions...........................7
Normal Operating Sounds and Sights..........29
Handle Installation......................................9
Care and Cleaning.....................................30
Connecting Water Supply...........................10
Before you Call..........................................34
Controls....................................................12
Major Appliance Warranty..........................39
www.frigidaire.com USA 1-800-944-9044
www.frigidaire.ca Canada 1-800-265-8352
A00535104 (January 2016)
Important Safety Instructions.......................2
IMPORTANT SAFETY INSTRUCTIONS
WARNING
Please read all instructions before using this
refrigerator.
For your Safety
• DO NOT store or use gasoline, or other
flammable liquids in the vicinity of this or
any other appliance. Read product labels for
warnings regarding flammability and other
hazards.
• DO NOT operate the refrigerator in the
presence of explosive fumes.
• Avoid contact with any moving parts of
automatic ice maker.
• Remove all staples from the carton. Staples
can cause severe cuts, and also destroy
finishes if they come in contact with other
appliances or furniture.
Definitions
This is the safety alert symbol. It is
used to alert you to potential personal injury
hazards. Obey all safety messages that follow
this symbol to avoid possible injury or death.
DANGER
DANGER indicates an imminently hazardous
situation which, if not avoided, will result in
death or serious injury.
Installation Checklist
Doors
 Handles are secure and tight
 Door seals completely to cabinet on all
sides
 Freezer door is level across the top
Leveling
 Refrigerator is level, side-to-side and
tilted ¼” (6mm) front-to-back
 Toe grille is properly attached to
refrigerator
 Cabinet is setting solid on all corners
Electrical Power
 House power turned on
 Refrigerator plugged in
Ice Maker
 House water supply connected to
refrigerator
 No water leaks present at all connections
- recheck in 24 hours
 Ice maker is turned ON
 Ice & water dispenser operates correctly
 Front filter must be flush with filter
housing (select models)
Final Checks
 Shipping material removed
 Fresh food and freezer temperatures set
WARNING
WARNING indicates a potentially hazardous
situation which, if not avoided, could result
in death or serious injury.
CAUTION
CAUTION indicates a potentially hazardous
situation which, if not avoided, may result in
minor or moderate injury.
IMPORTANT
IMPORTANT indicates installation, operation
or maintenance information which is
important but not hazard-related.
2
 Crisper humidity controls set
 Registration card sent in
Child Safety
Destroy or recycle the carton, plastic bags, and
any exterior wrapping material immediately
after the refrigerator is unpacked. Children
should NEVER use these items to play.
Cartons covered with rugs, bedspreads, plastic
sheets or stretch wrap may become airtight
chambers, and can quickly cause suffocation.
Proper Disposal of your
Refrigerator or Freezer
Risk of child entrapment
Child entrapment and suffocation are not
problems of the past. Junked or abandoned
refrigerators or freezers are still dangerous
– even if they will sit for “just a few days”. If
IMPORTANT SAFETY INSTRUCTIONS
you are getting rid of your old refrigerator or
freezer, please follow the instructions below to
help prevent accidents.
Proper Disposal of Refrigerators/Freezers
We strongly encourage responsible appliance
recycling/disposal methods. Check with your utility
company or visit www.energystar.gov/recycle for
more information on recycling your old refrigerator.
Before you throw away your old
refrigerator/freezer:
• Remove doors.
• Leave shelves in
place so children
may not easily
climb inside.
• Have refrigerant
removed by a
qualified service
technician.
IMPORTANT
CFC/HCFC Disposal
Your old refrigerator may have a cooling system
that used CFCs or HCFCs (chlorofluorocarbons
or hydrochlorofluorocarbons). CFCs and HCFCs
are believed to harm stratospheric ozone if
released to the atmosphere. Other refrigerants
may also cause harm to the environment if
released to the atmosphere.
If you are throwing away your old refrigerator,
make sure the refrigerant is removed for
proper disposal by a qualified technician. If
you intentionally release refrigerant, you may
be subject to fines and imprisonment under
provisions of environmental legislation.
WARNING
These guidelines must be followed to ensure
that safety mechanisms in this refrigerator
will operate properly.
refrigerator to a Ground Fault Interrupter
(GFI) circuit. Do not use an extension
cord or adapter plug.
• If the power cord is damaged, it should be
replaced by an authorized service technician
to prevent any risk.
• Never unplug the refrigerator by pulling on
the power cord. Always grip the plug firmly,
and pull straight out from the receptacle to
prevent damaging the power cord.
• Unplug the refrigerator before cleaning and before
replacing a light bulb to avoid electrical shock.
• Performance may be affected if the voltage
varies by 10% or more. Operating the
refrigerator with insufficient power can
damage the compressor. Such damage is
not covered under your warranty.
• Do not plug the unit into an electrical outlet
controlled by a wall switch or pull cord to prevent
the refrigerator from being turned off accidentally.
IMPORTANT
Pressing and holding the On/Off button for
three seconds, located on the temperature
control panel (Electronic controls), or
turning the Freezer and Fresh Food controls
to “0” (Mechanical controls) will disable
your refrigerator’s cooling system, but does
not disconnect the power to the light bulb
and other electrical components. To turn off
power to your refrigerator you must unplug
the power cord from the electrical outlet.
Grounding type wall receptacle
Do not, under any
circumstances,
cut, remove, or
bypass the
grounding prong.
Electrical information
• The refrigerator must be plugged into
its own dedicated 115 Volt, 60 Hz.,
15 Amp, AC only electrical outlet. The
power cord of the appliance is equipped
with a three-prong grounding plug for your
protection against electrical shock hazards.
It must be plugged directly into a properly
grounded three prong receptacle. The
receptacle must be installed in accordance
with local codes and ordinances. Consult
a qualified electrician. Avoid connecting
Power cord with
3-prong gounded plug
CAUTION
To avoid personal injury or property
damage, handle tempered glass shelves
carefully. Shelves may break suddenly if
nicked, scratched, or exposed to sudden
temperature change.
3
FEATURES AT A GLANCE
Features may vary according to model
Ice Cream Shelf
Ice Maker
Air Filter
SpillSafe®
Adjustable Shelf
Water Filter
Fixed
Door Bin
Dairy
Compartment
Ice
Container
Door Bin
SpillSafe®
Adjustable
Shelf
Wine Rack
Tall Bottle
Retainer
Door Bin
Special Item
Rack
Meat Keeper
and Cover
Shelf
Tilt Out
Door Bin
Small
Basket
Large
Glide Out
Basket
Can Rack
Crisper Pan
and Cover
Fixed
Door Bin
Toe Grille
IMPORTANT
Features not included with your refrigerator can be purchased at
www.frigidaire.com or by calling 1-800-944-9044.
4
INSTALLATION
This Use & Care Guide provides general
operating instructions for your model. Use
the refrigerator only as instructed in this
Use & Care Guide. Before starting the
refrigerator, follow these important first
steps.
Location
• Choose a place that is near a grounded
electrical outlet. Do Not use an extension
cord or an adapter plug.
• If possible, place the refrigerator out of
direct sunlight and away from the range,
dishwasher or other heat sources.
Toe Grille Installation and
Removal
To install toe grille
1 Open both doors. Slide left and right
sides of toe grille over lower hinges of
refrigerator.
2 While pushing toe grille firmly against
cabinet, fasten bottom clips of toe grille to
cabinet.
3 Fasten top clips to cabinet.
4 Close the doors. Fasten right and left side
clips into groove of bottom hinge.
• The refrigerator must be installed on a floor
that is level and strong enough to support a
fully loaded refrigerator.
• Consider water supply availability for models
equipped with an automatic ice maker. If
you do not hook up water to the refrigerator,
remember to turn the ice maker off.
CAUTION
Do Not install the refrigerator where the
temperature will drop below 55°F (13°C) or
rise above 110°F (43°C). The compressor
will not be able to maintain proper
temperatures inside the refrigerator.
Do Not block the toe grille on the lower front
of your refrigerator. Sufficient air circulation
is essential for the proper operation of your
refrigerator.
Installing Toe Grille
4
Allow the following clearances for ease
of installation, proper air circulation, and
plumbing and electrical connections:
4
2
3
2
1
To remove toe grille
1 With both doors closed, unfasten right
and left side clips of toe grille from bottom
hinge groove.
2 Open both doors. Press firmly on top of
toe grille until top of toe grille pops off.
3 Pull toe grille outward toward your body
and off of lower hinges.
Removing Toe Grille
Installation
Installation clearances
1 3
1
2
1
3
2
3
Sides & Top
⅜ inch
Back1 inch

NOTE
If your refrigerator is placed with the door
hinge side against a wall, you may have to
allow additional space so the door can be
opened wider.
5
INSTALLATION
Door Opening

To level the doors using the adjustable
lower hinge (some models):
NOTE
The refrigerator doors are designed to shut
by themselves within a 20 degree opening.
Your refrigerator should be positioned to
allow easy access to a counter or table when
removing food. For best use of drawers and
freezer baskets, the refrigerator should be
in a position where both the refrigerator and
freezer doors can be fully opened.
Guidelines for final positioning of your
refrigerator:
• All four corners of the cabinet must rest
firmly on the floor.
• The cabinet should be level at the front and
rear.
1 Before leveling either door, remove set
screw that locks door height into position.
(The door cannot be adjusted without set
screw removed).
2 If the refrigerator door is lower than the
freezer door, raise the refrigerator door by
turning the adjustment screw clockwise
using a 7/16 inch wrench. (See illustration.)
3 If the freezer door is lower than the
refrigerator door, raise the freezer door by
turning the adjustment screw clockwise
using a 7/16 inch wrench. (See illustration.)
Door
Door
• The sides should tilt ¼ inch (6 mm) from
front to back (to ensure that doors close and
seal properly).
• Doors should align with each other and be
level.
All of these conditions can be met by
raising or lowering the adjustable front
rollers.
To level the cabinet using the front
rollers:
1 Open both doors and remove the toe
grille (see “Toe Grille Installation and
Removal” in the “Installation” section).
2 Close the doors and use a flat-blade
screwdriver or ⅜ inch socket wrench to
raise or lower the front rollers.
3 Ensure both doors are bind-free with their
seals touching the cabinet on all four
sides.
Raise
Raise
Door
Raise
Door
4 After leveling, verify door stop contacts
lower hinge and top of door does
not contact upper hinge through full
movement of door (from fully closed to
fully open).
5 Reinstall set screw, locking the door
height.
Door Stop
Flange
Open Door
Hinge Flange
Set Screw
(some models)
Hinge
7/16" Wrench and
3/32" Hex Key (some models)
6 Replace the toe grille by fitting it into
place (see “Toe Grille Installation and
Removal” in the “Installation” section).
6
DOOR REMOVAL INSTRUCTIONS
Tools Necessary:
4 Close the doors.
To remove the refrigerator top hinge
cover:
1 Remove the three screws from each cover
over the top door hinges.
2 Lift hinge cover straight up and off.
Rear Cover Front Cover
Screw
Screws
Top
Hinge
Cover
Phillips™
Head
Hinge
Screws
Top
Hinge
or
Adjustable
Wrench
Socket
Wrench Set
To remove the refrigerator door:
1 Trace lightly around the door’s top hinge
with a pencil. This makes reinstallation
easier.
or
3/8" Fixed
Wrench
Top Hinge
Cover Front
Screw
Top
Hinge
Screw
Top Hinge
Cover Rear
Screw
Bottom
Hinge
Screw
To prepare for removing the doors:
1 Make sure the electrical power cord is
unplugged from the wall outlet.
2 Remove the two screws from the top
hinge. Lift the door off of the bottom
hinge and set it aside.
2 Open both doors and remove the toe
grille (as explained in the Installation
Instructions that came with your
appliance).
3 Remove any food from the door shelves.
7
DOOR REMOVAL INSTRUCTIONS
3 Remove the two bottom hinge screws and
hinge if necessary.
Door
Hinge
Assembly
Closer
Pin
Screws
Hinge
Adjustable Hinge (some models)
To reinstall the refrigerator door, reverse the
above steps.
To remove the freezer top hinge cover:
1 Remove the two screws from each cover
over the top door hinges.
2 Lift hinge cover straight up and off.
Front
Cover Screws
Top Hinge
Cover
connector releases when you press its
outer sleeve inward.
4 Remove the screws from the top hinge
and pull the multi-wire cable through it.
Lift the door off of the bottom hinge.
5 Remove the two bottom hinge screws and
hinge if necessary.
To Disconnect
1. Press outer ring against face of
fitting
2. Pull to
remove tube
To Connect
Insert tube and push until mark
touches face of fitting
Door
Rear Cover
Screw
Closer
Hinge
Screws
Water
Line
Tubing
Pin
Hinge
Hinge
Assembly Screws
Adjustable Hinge (some models)
Multi-Wire
Cable
Door
Top
Hinge
To remove the freezer door:
1 Detach the
multi-wire
cable
connector
located
above the
top hinge.
Grasp both
sides of the
connector
firmly and
pull apart.
2 Trace lightly around the hinge with a
pencil. This makes reinstallation easier.
3 Detach the water tube from the connector
located below the freezer door. The
8
Water
Line
Tubing
Hinge
Assembly Screws
Non-Adjusting Hinge (some models)
6 Lay the door on its side to avoid damage to the
water tube extending from the bottom hinge.
To reinstall the freezer door, reverse the above steps.
CAUTION
Be sure doors are set aside in a secure position
where they cannot fall and cause personal injury.
HANDLE INSTALLATION
CAUTION
Frigidaire Professional®
Freezer Upper
End Cap
Wear gloves and safety goggles and
use extreme CAUTION when installing
these handles. The rounded end of the
handles may be sharp (some models).
IMPORTANT
To ensure proper installation of
handles, please review these
instructions and illustrations thoroughly
prior to installing the handles.
A
Refrigerator Upper
End Cap
A
B
B
B
B
1 Remove handles from protective
packaging.
2 Position freezer handle end caps
over upper and lower pre-installed
shoulder bolts (A) that are fastened
into door, ensuring the holes for the
set screws are facing towards the
refrigerator door.
3 While holding handle firmly against
door, fasten furthermost upper and
furthermost lower Allen set screws
(B) with supplied Allen wrench.
4 Firmly tighten the inside Allen set
screws.
A
Freezer Lower
End Cap
A
Refrigerator Lower
End Cap
Frigidaire Gallery®
Freezer Upper
End Cap
Refrigerator Upper
End Cap
Freezer Lower
End Cap
Refrigerator Lower
End Cap
5 Repeat steps 2 through 4 to install
refrigerator handle. Ensure the holes
for the set screws are facing towards
the freezer door.

NOTE
All set screws should be tightened
and sub-flush (Allen set screw should
be seated just below the surface of
the end cap) of handle end cap. The
end caps should be drawn tight to
freezer and refrigerator doors with
no gaps.
Ensure Handle Set Screws
are Facing Each Other
with Doors Closed
9
CONNECTING THE WATER SUPPLY
WARNING
To avoid electric shock, which can cause
death or severe personal injury, disconnect
the refrigerator from electrical power before
connecting a water supply line to the
refrigerator.
CAUTION
To Avoid Property Damage:
• Copper or Stainless Steel braided tubing
is recommended for the water supply
line. Water supply tubing made of ¼
inch plastic is not recommended to be
used. Plastic tubing greatly increases
the potential for water leaks, and the
manufacturer will not be responsible for
any damage if plastic tubing is used for
the supply line.
• DO NOT install water supply tubing in
areas where temperatures fall below
freezing.
• Chemicals from a malfunctioning softener
can damage the ice maker. If the ice
maker is connected to soft water, ensure
that the softener is maintained and
working properly.
IMPORTANT
Ensure that your water supply line
connections comply with all local plumbing
codes.
Before Installing The Water Supply Line,
You Will Need:
• Basic Tools: adjustable wrench, flat-blade
screwdriver, and PhillipsTM screwdriver
• Access to a household cold water line with
water pressure between 30 and 100 psi.
• A water supply line made of ¼ inch
(6.4 mm) OD, copper or stainless steel
tubing. To determine the length of tubing
needed, measure the distance from the
ice maker inlet valve at the back of the
refrigerator to your cold water pipe. Then
add approximately 7 feet (2.1 meters),
so the refrigerator can be moved out for
cleaning (as shown).
10
• A shutoff valve to connect the water supply
line to your household water system. Do not
use a self-piercing type shutoff valve.
• Do not re-use compression fitting or use
thread seal tape.
• A compression nut and ferrule (sleeve) for
connecting a copper water supply line to the
ice maker inlet valve.

NOTE
Check with your local building authority
for recommendations on water lines and
associated materials prior to installing
your new refrigerator. Depending on
your local/state building codes, Frigidaire
recommends for homes with existing
valves its Smart Choice® water line kit
5304490728 (with a 6 ft. Stainless Steel
Water Line) or 5304493869 (with a 6
ft. Polyline Water Line) and for homes
without an existing valve, Frigidaire
recommends its Smart Choice® water
line kit 5304490717 (with a 20 ft. copper
water line with self-tapping saddle valve).
Please refer to www.frigidaire.com/store
for more information.
To Connect Water Supply Line To Ice
Maker Inlet Valve
1 Disconnect refrigerator from electric
power source.
2 Place end of water supply line into sink or
bucket. Turn ON water supply and flush
supply line until water is clear. Turn OFF
water supply at shutoff valve.
3 Remove plastic cap from water valve inlet
and discard cap.
4 If you use copper tubing - Slide brass
compression nut, then ferrule (sleeve)
onto water supply line. Push water supply
line into water valve inlet as far as it
will go (¼ inch/6.4 mm). Slide ferrule
(sleeve) into valve inlet and finger tighten
compression nut onto valve. Tighten
another half turn with a wrench; DO NOT
over tighten. See Figure 1.
If you use stainless steel or polyline
tubing - The nut and ferrule are
already assembled on the tubing. Slide
compression nut onto valve inlet and
finger tighten compression nut onto valve.
Tighten another half turn with a wrench;
DO NOT over tighten. See Figure 2.
CONNECTING THE WATER SUPPLY
5 With steel clamp and screw, secure water
supply line (copper tubing only) to rear
panel of refrigerator as shown.
6 Coil excess water supply line (copper
tubing only), about 2½ turns, behind
refrigerator as shown and arrange coils so
they do not vibrate or wear against any
other surface.
Plastic Water Tubing
to Ice Maker
Fill Tube
Water Line
7 Turn ON water supply at shutoff valve and
tighten any connections that leak.
Water Valve
Bracket
8 Reconnect refrigerator to electrical power
source.
Valve Inlet
9 To turn ice maker on, lower wire signal
arm (side mounted) or set the ice maker’s
On/Off power switch to the “I” position
(rear mounted).
Plastic Water
Tubing to Ice
Maker Fill
Tube
Steel
Clamp
Brass
Compression
Nut
Ferrule
(Sleeve)
Copper
water line
Water Valve
Bracket
Valve Inlet
Water Valve
Copper water line
from household
water supply
Steel
Clamp
Water Valve
Water line
from household water supply
(Include enough tubing in loop to allow
moving refrigerator out for cleaning.)
Figure 2
IMPORTANT
After connecting the water supply, refer to
“How to Prime the Water Supply System”
for important information about priming an
empty water supply system.
To ensure that your water dispenser works
properly, the water supply system must
be completely filled with water when
your refrigerator is first connected to the
household water supply line.
(Include enough tubing in loop to allow
moving refrigerator out for cleaning.)
Figure 1
11
CONTROLS
FRIGIDAIRE &
FRIGIDAIRE GALLERY
User Interface (varies by model)
Enlarged view of user interface display menu (varies by model)
12
FRIGIDAIRE &
FRIGIDAIRE GALLERY
options
(∧ or ∨)
Used to enter and exit the
options menu and make
selections.
exit
Toggles the options and run
modes.
control
locked
CONTROLS
air filter
Displays the current status of
the air filter (Good, Order, or
Replace). To reset the filter
status to “Good”, press and
hold the “set” key for three
seconds.
While in the locked state,
you will not be able to
change any settings on the
display nor dispense ice and
water. The “Control Locked”
indicator will flash and an
audible warning tone is
played.
default
settings
While in the default option,
press and hold the set key
for three seconds to reset all
refrigerator settings to their
factory default settings.
set (+ or -)
Selects the current menu
selection option.
light
Toggles dispenser light On
and Off.
water
quick
freeze
on off
Activates a faster rate for
freezing food. Deactivates
after 12 hours.
Press the “water” key
to select water. A green
indicator light will be
illuminated above the active
feature.
quick ice
Increases the production
of ice. Deactivates after 12
hours.
cube
Press the “cube” key to
select cubed ice. A green
indicator light will be
illuminated above the active
feature.
crush
Press the “crush” key
to select crushed ice. A
green indicator light will be
illuminated above the active
feature.
on off
display
on off
Toggles the temperature
displays On and Off.
refrigerator
temp
Allows the temperature
set-points to be adjusted.
Control temperatures range
from +33°F / +1°C to +47°F
/ +8°C.
freezer
temp
Allows the temperature
set-points to be adjusted.
Control temperatures range
from -6°F / -21°C to +6°F /
-15°C.
Setting cooling temperatures
mode
°F °C
Toggles display from
Fahrenheit to Celsius.

power off
Press and hold for three
seconds to turn off the
cooling system. It also turns
off the ice maker and all
dispenser functions. The
display will read “power off”.
water filter
Displays the current status of
the water filter (Good, Order,
or Replace). To reset the filter
status to “Good”, press and
hold the “set” key for three
seconds.
When you first power on the refrigerator, the
temperature displays 0°F and 37°F. After a
few seconds, both of the displays will switch
to “HI”. The displays will continue to show
“HI” for 20 minutes. After 20 minutes, the
High Temp alarm will sound and both
displays will show the actual temperature.
NOTE
1 Plus (+) and Minus (-) indicators are
located on the right side of the control
panel.
2 Press the + or - indicator to adjust the
temperature to the desired setting.
13
CONTROLS
Alarms
Power
Failure
Sabbath Mode
In the event of a power failure,
the power fail alert will be
illuminated. Press alarm reset to
acknowledge the alarm. Other
modes may be turned off until
the alarm is acknowledged.
When the power fail alert is
acknowledged, the refrigerator
will resume normal operation.
The high temp alarm may
also be illuminated until a safe
operating range temperature
has been reached.
Freezer
Temp
If the freezer temperature
reaches 26°F or greater, the
alarm will sound and the
temperature will flash. You can
disable the alarm by pressing
the set key but the “High Temp”
indicator will illuminate until the
temperature goes below 26°F.
Fresh Food
Temp
If the fresh food temperature
reaches 55°F or greater, the
alarm will sound and the
temperature will flash. You can
disable the alarm by pressing
the set key but the “High Temp”
indicator will illuminate until the
temperature goes below 55°F.
Door Ajar
If the freezer or fresh food
doors have been left open for
five minutes or more, an alarm
will sound and the door ajar
indicator will illuminate on the
display. Press the set key to
reset any system alarms.
Flapper
When “Cube” or “Crush” is
selected, if the flapper (or ice
chute door) is being held open
by a jammed ice cube, an alarm
will sound for two minutes.
The alarm will reset after two
minutes or when the ice cube
is removed and the set key is
pressed to reset.
14
FRIGIDAIRE &
FRIGIDAIRE GALLERY
The Sabbath Mode is a feature that disables
portions of the refrigerator and its controls
in accordance with observance of the weekly
Sabbath and religious holidays within the
Orthodox Jewish community.
Sabbath Mode is turned ON and OFF by
pressing and holding both the “∨” and “+” for
five seconds. The display shows “Sb” while in
Sabbath mode.
In the Sabbath Mode, the High Temp alarm
is active for health reasons. For example,
if the door is left ajar the High Temp alarm
is activated. The refrigerator will function
normally once the door is closed, without
any violation of the Sabbath/Holidays. The
High Temp alarm is permitted when cabinet
temperature is outside the safe zone for 20
minutes. The alarm silences itself after 10
minutes while the High Temp icon stays lit until
the Sabbath mode is exited.
For further assistance, guidelines for proper
usage and a complete list of models
with the Sabbath feature, please visit
the web at http:\\www.star-k.org.

NOTE
While in Sabbath Mode, neither the lights,
dispenser, nor the control panel will work
until Sabbath Mode is deactivated.
Refrigerator stays in Sabbath Mode
after power failure recovery. It must be
deactivated with the buttons on the control
panel.

NOTE
Although you have entered the Sabbath
Mode, the ice maker will complete the
cycle it had already initiated. The ice cube
compartment will remain cold and new ice
cubes can be made with standard trays.
FRIGIDAIRE
PROFESSIONAL
CONTROLS
User Interface In-Door Controls
(options may vary)
POWER
ON-OFF
Press and hold for three seconds
to turn off the cooling system. It
also turns off the ice maker and all
dispenser functions. The display will
read “OFF”.
DEFAULT
SETTINGS
Press and hold for three seconds to
reset all refrigerator settings to their
factory default settings.
ICE MAKER
ON-OFF
Press and hold for 3 seconds to
toggle the ice maker in the freezer
compartment “ON” or “OFF”.
POWERPLUS
FREEZE
Activates a faster rate for freezing
food and increases ice production
in the freezer. Deactivates after 12
hours.
AIR FILTER
Displays the current status of the air
filter (GOOD, ORDER, or REPLACE).
To reset the filter status to “GOOD”,
press and hold for three seconds.
WATER FILTER
Displays the current status of the
water filter (GOOD, ORDER, or
REPLACE). To reset the filter status
to “GOOD”, press and hold for three
seconds.
REFRIGERATOR
TEMP
Allows the temperature setpoints to be adjusted. Press the
“-” or “+” indicator to adjust the
temperature to the desired setting.
Control temperatures range from
+33°F / +1°C to +43°F / +6°C.
FREEZER TEMP
Allows the temperature setpoints to be adjusted. Press the
“-” or “+” indicator to adjust the
temperature to the desired setting.
Control temperatures range from
-6°F / -21°C to +4°F / -16°C.
15
FRIGIDAIRE
PROFESSIONAL
CONTROLS
Dispenser Controls
(options may vary)
Alarms
Power Failure
In the event of a power failure, the “POWER
FAIL” alert will be illuminated. Press “MUTE
ALARM” to acknowledge the alarm. Other
modes may be turned off until the alarm is
acknowledged. While a “POWER FAIL” alert
is displayed on the control panel, the unit will
continue normal operation. The “POWER FAIL”
alert on the control panel will be removed once
the user acknowledges the power fail condition
by pressing “MUTE ALARM” or “DEFAULT
SETTINGS”.
Freezer Temp
WATER
Press the “WATER” key to
select water.
CUBES
Press the “CUBES” key to
select cubed ice.
CRUSHED
Press the “CRUSHED” key to
select crushed ice.
light
Toggles dispenser light on
and off.
If the freezer temperature reaches 26°F
or greater, the alarm will sound and the
temperature will flash and the dispenser
control will display “HIGH TEMP DETECTED”.
You can disable the alarm by pressing “MUTE
ALARM” but the “HIGH TEMP DETECTED”
indicator will illuminate until the temperature
goes below 26°F.
Fresh Food Temp
If the fresh food temperature reaches 55°F
or greater, the alarm will sound and the
temperature will flash and the dispenser
control will display “HIGH TEMP DETECTED”.
You can disable the alarm by pressing “MUTE
ALARM” but the “HIGH TEMP DETECTED”
indicator will illuminate until the temperature
goes below 55°F.
Door Ajar
If the freezer or fresh food doors have been
left open for five minutes or more, an alarm
will sound and the door ajar indicator will
illuminate on the display. Press “MUTE ALARM”
to reset any system alarms.
Flapper
When “CUBES” or “CRUSHED” is selected,
if the flapper (or ice chute door) is being
held open by a jammed ice cube, an alarm
will sound for two minutes and the current
selection will blink on the dispenser control.
The alarm will reset after two minutes or when
the ice cube is removed.
16
FRIGIDAIRE
PROFESSIONAL
CONTROLS
Sabbath Mode
The Sabbath Mode is a feature that disables
portions of the refrigerator and its controls
in accordance with observance of the weekly
Sabbath and religious holidays within the
Orthodox Jewish community.
Sabbath Mode is turned ON and OFF by
simultaneously pressing and holding both
the freezer “-” and the refrigerator “+” for
five seconds. The display shows “Sb” while in
Sabbath mode.
In the Sabbath Mode, the “HIGH TEMP” alarm
is active for health reasons. For example, if
the door is left ajar the “HIGH TEMP” alarm
is activated. The refrigerator will function
normally once the door is closed, without
any violation of the Sabbath/Holidays. The
“HIGH TEMP” alarm is permitted when cabinet
temperature is outside the safe zone for 20
minutes. The alarm silences itself after 10
minutes while the “HIGH TEMP” icon stays lit
until the Sabbath mode is exited.
For further assistance, guidelines for proper
usage and a complete list of models
with the Sabbath feature, please visit
the web at
http:\\www.star-k.org.

NOTE
While in Sabbath Mode, neither the lights,
dispenser, nor the control panel will work
until Sabbath Mode is deactivated.
Refrigerator stays in Sabbath Mode
after power failure recovery. It must be
deactivated with the buttons on the control
panel.

NOTE
Although you have entered the Sabbath
Mode, the ice maker will complete the
cycle it had already initiated. The ice cube
compartment will remain cold and new ice
cubes can be made with standard trays.
17
STORAGE FEATURES
CAUTION
To avoid personal injury or property damage,
handle tempered glass shelves carefully.
Shelves may break suddenly if nicked,
scratched, or exposed to sudden temperature
change. Allow the glass shelves to stabilize
to room temperature before cleaning. Do not
wash in dishwasher.
The dairy compartment, which is warmer than
the general food storage section, is intended
for short term storage of cheese, spreads, or
butter.
Fresh Drawers with Humidity
Control (some models)
The fresh drawers, located under the bottom
refrigerator shelf, are designed for storing
fruits, vegetables, and other fresh produce.
The fresh drawers feature humidity control
Cantilever Shelf Adjustment
which allows you to adjust the humidity within
Refrigerator shelves are easily adjusted to
the drawer. This can extend the life of fresh
suit individual needs. Before adjusting the
vegetables that keep best in high humidity.
shelves, remove all food. Cantilever shelves are
Wash items in clear water and remove excess
supported at the back of the refrigerator.
water before placing them in the crispers.
Items with strong odors or high moisture
To adjust cantilever shelves:
content should be wrapped before storing.
1 Lift front edge up.
2 Pull shelf out.
Replace the shelf by inserting the hooks at
rear of the shelf into the wall bracket. Lower
the shelf into the desired slots and lock into
position.
SpillSafeTM glass shelves (some models) catch
and hold accidental spills. In some models, the
SpillSafeTM shelves slide out for easy access
to food and for fast cleaning. The shelves slide
out independently of their mounting brackets.
Just pull the front of the shelf forward.
Shelves can be extended as far as the stopper
will allow but are not removable from their
mounting brackets.
1
Higher Humidity
Lower Humidity
Crisper Humidity Control

NOTE
Leafy vegetables keep best when stored
with the humidity control set on Higher
Humidity, or in a drawer without a
Humidity Control. This keeps incoming air
to a minimum and maintains maximum
moisture content.
Crispers
2
Cantilever Glass Shelf
Cantilever Sliding
Glass Shelf
Door storage
Door bins and shelves are provided for
convenient storage of jars, bottles, and cans.
Frequently used items can be quickly selected.
Some models have door bins that can
accommodate gallon-sized plastic drink
containers and economy-sized jars and
containers. Some bins are adjustable for
maximum storage capacity.
18
Crispers allow you
the flexibility to store
any manner of items
including fruits,
vegetables, nuts, etc.
Crispers do not feature
humidity controls.
Crisper Drawer
Cool Drawer (some models)
Some models are equipped with a Cool Drawer
for storage of luncheon meats, spreads,
cheeses, and other deli items. This drawer
does not have a separate temperature control.
STORAGE FEATURES
Chill Drawer (some models)
Some models are equipped with a Chill Drawer. Chill Drawer temperatures can be adjusted by
sliding the Chill Drawer Temperature Control in either direction. Use this pan for short term
storage of bulk meat items. If meats are to be kept longer than one or two days, they should be
frozen. The Chill Drawer is fixed and cannot be moved up or down. If fruits or vegetables are to
be stored in the Chill Drawer, set the Chill Drawer Temperature Control to a warmer setting to
prevent freezing.
Colder
Warmer
Chill Drawer
with Temperature Control
19
AUTOMATIC ICE & WATER DISPENSER
FRIGIDAIRE & FRIGIDAIRE GALLERY
Priming the Water Supply
System
Your refrigerator’s water supply system
includes several tubing lines, an advanced
water filter, and a distribution valve bank to
ensure ample supply to the ice and water
dispenser at all times. This system needs to
be completely filled with water when first
connected to an external supply line.
CAUTION
For proper dispenser operation,
recommended water supply pressure
should fall between 30 psi and 100 psi.
Excessive pressure may cause water filter to
malfunction.
To prime the water supply system:
1 Begin filling the system by pressing and
holding a drinking glass against the water
dispenser paddle.
2 Keep the glass in this position until water
comes out of the dispenser. It may take
about 1½ minutes.
3 Continue dispensing water for about four
minutes to flush the system and plumbing
connections of any impurities (stopping to
empty the glass as necessary).

NOTE

NOTE
The water dispenser has a built-in device
that shuts off the water flow after three
minutes of continuous use. To reset this
shutoff device, simply release the dispenser
paddle.
Dispensed water is not chilled. For colder
water, add ice to cup or container before
dispensing water.
Ice Maker Operation & Care
The ice maker, ice bin, and dispenser feeding
mechanism are located in the top of the freezer
compartment. After the refrigerator is installed
properly and has cooled for several hours, the
ice maker can produce ice within 24 hours. It
can completely fill an ice bin in about two days.
20
Ice Production: What to Expect
How much ice will a side-mounted ice
maker produce in 24 hours?
A side mounted ice maker will produce 4 to
4.5 pounds of ice every 24 hours, depending
on usage conditions. Ice is produced at a rate
of 8 cubes every 75 to 90 minutes.
How Much Ice Will a Rear Mounted Ice
Maker Produce in 24 Hours?
A rear mounted ice maker will produce 3 to
4 pounds of ice every 24 hours, depending on
usage conditions. Ice is produced at a rate of
8 cubes every 75 to 90 minutes.
How much ice can be stored in the bin?
When completely full, the bin in standard
depth units will hold about 9.5 pounds of ice.
The bin in counter depth units will hold about
5.5 pounds of ice.
Using the Ice Maker after Installation
Before making ice for the first time, be sure
to prime the water supply system. Air in new
plumbing lines can result in two or three empty
ice maker cycles. Furthermore, if the system
is not flushed, the first ice cubes may be
discolored or have an odd flavor.
IMPORTANT
Your ice maker is shipped from the factory
with the wire signal arm in the ON position
(side mounted) or with the switch turned
ON (rear mounted). To ensure proper
function of your ice maker, hook up water
supply immediately or turn ice maker OFF
by lifting the wire signal arm until it clicks
and locks in the UP position (side mounted)
or turn the On/Off switch to the Off (0)
position (rear mounted). If the ice maker
is not turned off and the water supply
is not connected, the water valve will
make a loud chattering noise.
AUTOMATIC ICE & WATER DISPENSER
FRIGIDAIRE & FRIGIDAIRE GALLERY
Turning the REAR MOUNTED Ice
Maker On and Off
Ice Maker/Dispenser Tips
• Ice cubes stored too long may develop
an odd flavor. Empty the ice container as
Ice production is controlled by the ice maker’s
explained below.
ON/OFF power switch. To gain access to the
ice maker, pull the ice cream shelf out. Press
• Occasionally shake the ice container to keep
the switch to the “O” position to turn it Off and
ice separated.
press it to the “I” position to turn it On. The
•
If your refrigerator is not connected to a
ice maker also has a built-in wire signal arm,
water supply or the water supply is turned
which automatically stops ice production when
off, turn Off the ice maker.
the ice bin is full. DO NOT use this signal arm
to manually stop the ice maker.
• If you need a large quantity of ice at one
time, it is best to get cubes directly from the
ice container.
Off On
Wire
Signal Arm
• The following sounds are normal when the
ice maker is operating:
- Motor running
- Ice dropping into ice container
- Water valve opening or closing
- Ice loosening from tray
- Running water
• When dispensing ice, you will hear a
snapping or clicking sound when the ice
chute opens and closes.
• To avoid splashing, dispense ice into your
container before adding liquids.
IMPORTANT
Small ice cubes or ice chips jamming in the
ice maker may be a sign that your water
filter needs changing. If you have a side
mounted ice maker you may also experience
hollow cubes partially frozen cubes with
water inside. When these cubes are
harvested, they break open and spill water
over the other ice cubes in the ice container,
forming a solid mass of ice. As the water
filter nears the end of its useful life and
becomes clogged with particles, less water is
delivered to the ice maker during each cycle.
The ice maker can’t fill every cube in the ice
maker mold, leading to small cubes or chips
that can get caught between the ice ejector
blades and the stripper. Remember, if your
ice maker is jamming with small ice cubes or
it’s been six months or longer since you last
changed your water filter replace the water
filter with a new one. Poor quality household
water may require the filter to be changed
more frequently.
• It is normal for ice to fill to the top of the
ice bin.
• Turn Off the ice maker when cleaning the
freezer and during vacations.
- If you turn Off the ice maker for a
long period of time, you should also
turn off the water supply valve.
CAUTION
Chemicals from a malfunctioning water
softener can damage the ice maker. If the
water supply to your refrigerator is softened,
be sure the softener is maintained to work
properly.
21
AUTOMATIC ICE & WATER DISPENSER
FRIGIDAIRE & FRIGIDAIRE GALLERY
Cleaning the Ice Maker
Clean the ice maker and ice bin at regular
intervals, particularly before you take a
vacation or move.
To clean the ice maker:
1 Turn Off the ice maker.
2 Remove the ice bin by lifting up and out.
3 Empty and carefully clean the ice bin with
mild detergent. Rinse with clear water. Do
not use harsh or abrasive cleaners.
4 Allow the ice bin to dry completely before
replacing in the freezer.
IMPORTANT
When removing or replacing the ice bin,
DO NOT rotate the auger in the ice bin. If
the auger is accidentally rotated, you must
realign the auger by turning it in 90 degree
turns (see below) until the ice bin fits into
place with the drive mechanism. If the
auger is not properly aligned when
replacing the ice bin, the refrigerator will
only dispense Crushed Ice. The freezer door
may also not close properly causing warm
air to leak into the freezer.
5 Remove ice chips and clean the ice bin
shelf and the freezer door chute.
6 Replace the ice bin. Turn On the ice maker
to resume ice production.
Remove and empty the ice storage bin if:
• An extended power failure (one hour or
longer) causes ice cubes in the ice storage
bin to melt and freeze together, jamming the
dispenser mechanism.
• You do not use the ice dispenser frequently.
Ice cubes will freeze together in the bin,
jamming the dispenser mechanism.
Remove the ice storage bin and shake to
loosen the cubes or clean as explained above.
CAUTION
NEVER use an ice pick or similar sharp
instrument to break up the ice. This could
damage the ice storage bin and dispenser
mechanism.
22
Auger
AUTOMATIC ICE & WATER DISPENSER
FRIGIDAIRE PROFESSIONAL
Priming the water supply system Ice Maker and Storage Bin
Capacity
CAUTION
This ice maker should produce 2.5 to 3 pounds
For proper dispenser operation, recommended
water supply pressure should fall between
30 psi and 100 psi. Excessive pressure may
cause the system to malfunction.
1 Begin filling the system by pressing and
holding a drinking glass against the water
dispenser
paddle.
2 Keep the
glass
in this
position
until water
comes
out of the
dispenser.
It may
take
about 1½
minutes.
Dispenser
3 Continue
(varies by model)
dispensing
water for about four minutes to flush the
system and plumbing connections of any
impurities (stopping to empty the glass as
necessary).

NOTE

NOTE
The water dispenser has a built-in device that
shuts off the water flow after three minutes
of continuous use. To reset this shutoff
device, simply release the dispenser paddle.
of ice per 24 hours, depending on usage
conditions. Ice is produced at a rate of 10
cubes every 75 to 90 minutes.
How much ice can be stored in
the ice bin?
When completely full, the bin in standard
depth units will hold about 11 pounds of ice
(total weight of ice and bin will be about 15
pounds). The bin in counter depth units will
hold about 8.5 pounds of ice (total weight of
ice and bin will be about 12 pounds).
Turning the ice maker on and off
Ice production is controlled by the ice maker’s
On/Off feature on the control panel. Pressing
and holding the On/Off button toggles the ice
maker On/Off.
IMPORTANT
Turning off the ice maker simply disables
ice making. You will still be able to dispense
existing ice, and you will still be able to
dispense water.

NOTE
The ice maker also has a built-in plastic
signal arm that automatically stops ice
production when the ice bin is full. This
signal arm should not be used to manually
stop the ice maker.
Dispensed water is not chilled. For colder
water, add ice to cup or container before
dispensing water.
Ice maker operation & care
After the refrigerator is installed properly and
has cooled for several hours, the ice maker can
produce ice within 24 hours. The ice maker will
fill the ice bin from the rear. You must dispense
some ice to force the ice forward in the bin.
This will allow the bin to fill completely.
23
AUTOMATIC ICE & WATER DISPENSER
FRIGIDAIRE PROFESSIONAL
Using the ice maker after
installation
Before making ice for the first time, be sure
to prime the water supply system. Air in new
plumbing lines can result in two or three empty
ice maker cycles. Furthermore, if the system
is not flushed, the first ice cubes may be
discolored or have an odd flavor.
IMPORTANT
Your ice maker is turned on at the factory
so it can work as soon as you install your
refrigerator. If you cannot connect a water
supply, set the ice maker’s On/Off feature
to Off; otherwise, the ice maker’s fill valve
may make a loud chattering noise when it
attempts to operate without water.
IMPORTANT
On occasion, unusually small ice cubes may
be noticed in the bucket or in dispensed ice.
This could occur in normal operation of the
ice maker. If you start seeing these more
frequently, it may be an indication of low
water pressure or the water filter needs to be
replaced. As the water filter nears the end of its
useful life and becomes clogged with particles,
less water is delivered to the ice maker during
each cycle. Remember, if it’s been six months
or longer since you last changed your water
filter, replace the water filter with a new one.
Poor quality household water may require the
filter to be changed more frequently.
Ice maker/dispenser tips
• If your refrigerator is not connected to a
water supply or the water supply is turned
off, turn off the ice maker as described in
the previous section.
• The following sounds are normal when the
ice maker is operating:
- Motor running
- Ice dropping into ice bin
- Water valve opening or closing
- Running water
• When dispensing ice, you will hear a
snapping or clicking sound when the ice
chute opens and closes.
• If you need a large quantity of ice at one
time, it is best to get cubes directly from
the ice bin.
• Ice cubes stored too long may develop an
odd flavor. Empty the ice bin as explained
below.
• When dispensing cubed ice, it is normal to
have a small quantity of little pieces along
with the whole cubes.
• To avoid splashing, dispense ice into your
container before adding liquids.
• It is normal for ice to fill to the top of the
ice bin.
CAUTION
If the water supply to your refrigerator is
softened, be sure the softener is properly
maintained. Chemicals from a water softener
can damage the ice maker.
24
AUTOMATIC ICE & WATER DISPENSER
FRIGIDAIRE PROFESSIONAL
Cleaning the storage bin
Clean the ice
maker and ice
bin at regular
intervals,
especially prior
to vacation or
moving.
1 Turn off
the ice
maker.
2 Remove
the ice
Removing Ice Bin
bin by
lifting up slightly on the front of the bin
and pulling it straight out of the ice maker
housing.
Remove and empty the ice bin if:
• An extended power failure (one hour or
longer) causes ice cubes in the ice bin to
melt and refreeze together after power is
restored, jamming the dispenser mechanism.
• You do not use the ice dispenser frequently.
Ice cubes will freeze together in the bin,
jamming the dispenser mechanism.
Remove the ice bin and shake to loosen the
cubes or clean as explained above.
CAUTION
NEVER use an ice pick or similar sharp
instrument to break up the ice. This could
damage the ice bin and dispenser mechanism.
To loosen stuck ice, use warm water.
Before replacing the ice bin, make sure it is
completely dry.
IMPORTANT
CAUTION
Be sure to firmly support the underside
of the ice bin when removing it from the
refrigerator. A standard depth bin that is full
of ice will weigh about 15 pounds total, and
a counter depth bin that is full of ice will
weigh about 12 pounds total.
When removing or replacing the ice bin,
avoid rotating the auger in the ice bin. If
the auger is accidentally rotated, you must
realign the auger by turning it in 45 degree
turns (see below) until the ice bin fits into
place with the drive mechanism. If the
auger is not properly aligned when replacing
the ice bin, the refrigerator will not dispense
ice. The freezer door also may not close
properly causing warm air to leak into the
freezer compartment.
3 Empty and carefully clean the ice bin
with mild detergent. Do not use harsh or
abrasive cleaners. Rinse with clear water.
4 Allow the ice bin to dry completely before
replacing in the freezer.
5 Remove ice chips and clean the ice bin
shelf and the freezer door chute.
6 Replace the ice bin. Turn the ice maker on
to resume ice production.
Auger
Adjusting Ice Bin Auger
25
CHANGING THE FILTER
FRIGIDAIRE &
FRIGIDAIRE GALLERY
Locating the Filter
Water Filter
Your refrigerator is equipped with a water
filtering system. The water filter system filters
all dispensed drinking water, as well as the
water used to produce ice.
The water filter is located at the top right side
of the fresh food compartment.
Air Filter (some models)
The air filter is located at the top of the fresh
food compartment next to the water filter.
Replacing the Air Filter
In general, you should change the air filter
every six months (the filter status light on
the control panel prompts you to replace
the filter after six months) to ensure optimal
filtering of refrigerator odors. You may want
to adjust this time period depending on the
types and amounts of food you typically
store in your refrigerator. To replace your
PureSource UltraTM air filter:
Replacing the Water Filter
In general, you should change the water
filter every six months to ensure the
highest possible water quality. Water
Filter Status on the user interface prompts
you to replace the filter after a standard
amount of water (200 gallons/757 liters for
PureSource UltraTM) has flowed through the
system.
If your refrigerator has not been used for a
period of time (during moving for example),
change the filter before reinstalling the
refrigerator.
Filter Cartridge
1 Pull the air filter housing straight out.
2 Remove the old filter and discard it.
3 Unpack the new filter and place it inside
the housing.
4 Slide the housing back into position.
Air Filter
Ordering Replacement Filters
To order your replacement filters, please visit
our online store at www.frigidaire.com/store,
by calling toll-free at 877-808-4195, or by
visiting the dealer where you purchased your
refrigerator. Frigidaire recommends that you
order extra filters when you first install your
refrigerator, and that you replace your filters at
least once every six months.
Here are the product numbers to request when
ordering:
PureSource UltraTM Water Filter
Part# ULTRAWF
26
FRIGIDAIRE &
FRIGIDAIRE GALLERY
More about your Advanced
Water Filter
The PureSource UltraTM ice and
water filter system is tested and
certified to NSF/ANSI Standards
42, 53 and 401 for the reduction
of claims specified on the
performance data sheet.
CHANGING THE FILTER
7 After filling one glass of water, continue
flushing the system for about four
minutes.
8 Turn On the ice maker.
9 Press and hold the Water Filter button
on the Ice & Water Dispenser control
panel for three seconds. When the display
changes from “Red” to “Green,” the status
has been reset.
Do not use with water that is microbiologically
unsafe or of unknown quality without adequate
disinfection before or after the system.
Systems certified for cyst reduction may be
used on disinfected waters that may contain
filterable cysts.
Test & certification results:
• Rated Capacity - 200 gallons/757 liters for
PureSource UltraTM ice and water filter
• Rated service flow - .50 gallons per minute
• Operating Temp.: Min. 33°F, Max. 100°F
• Maximum Rated Pressure - 100 pounds per
square inch
• Recommended Minimum Operating
Pressure: 30 pounds per square inch
To replace your water filter:
It is not necessary to turn the water supply off
to change the filter. Be ready to wipe up any
small amounts of water released during the
filter replacement.
1 Turn Off the ice maker.
2 Remove the filter by pushing on the end/
face of the filter.
3 Slide the old water filter cartridge straight
out of the housing and discard it.
4 Unpackage the new filter cartridge. Using
the alignment guide, slide it gently into
the filter housing until it stops against
the snap-in connector at the back of the
housing.
5 Push firmly until the cartridge snaps into
place (you should hear a click as the
cartridge engages the snap-in connector).
6 Press a drinking glass against the water
dispenser while checking for any leaks at
the filter housing. Any spurts and sputters
that occur as the system purges air out of
the dispenser system are normal.
27
CHANGING THE FILTER
Locating the Filters
Your refrigerator is equipped with water
filtering system. The water filter system filters
all dispensed drinking water, as well as the
water used to produce ice. The filter is located
in the top right rear corner of the fresh food
compartment.
Water Filter
The water filter is located at the top right side
of the fresh food compartment.
Replacing the Water Filter
In general, you should change the water
filter every six months to ensure the highest
possible water quality. Water Filter Status
on the user interface prompts you to replace
the filter after a standard amount of water
(125 gallons/473 liters for PureSource
Ultra IITM) has flowed through the system.
If your refrigerator has not been used for a period
of time (during moving for example), change the
filter before reinstalling the refrigerator.
Filter Cartridge
Ordering Replacement Filters
To order your replacement filters, please visit
our online store at www.frigidaire.com/store,
by calling toll-free at 1-800-599-7569, or by
visiting the dealer where you purchased your
refrigerator. Frigidaire recommends that you
order extra filters when you first install your
refrigerator, and that you replace your filters at
least once every six months.
Here is the product number to request when
ordering:
PureSource Ultra IITM Water Filter
Part #EPTWFU01

NOTE
When ordering your replacement filter,
please reorder the same filter type that is
currently in your refrigerator.
28
FRIGIDAIRE
PROFESSIONAL
More about your Advanced
Water Filter
The PureSource Ultra IITM
ice and water filter system is
tested and certified to NSF/ANSI
Standards 42, 53 and 401 for the
reduction of claims specified on
the performance data sheet.
Do not use with water that is microbiologically
unsafe or of unknown quality without adequate
disinfection before or after the system. Systems
certified for cyst reduction may be used on
disinfected waters that may contain filterable cysts.
Test & certification results:
• Rated Capacity - 125 gallons/473 liters for
PureSource Ultra IITM ice and water filter
• Rated service flow - .65 gallons per minute
• Operating Temp: Min. 33°F, Max. 100°F
• Maximum Rated Pressure - 100 pounds per
square inch
• Recommended Minimum Operating
Pressure: 30 pounds per square inch
To replace your PureSource Ultra IITM
water filter:
It is not necessary to turn the water supply off
to change the filter. Be ready to wipe up any
small amounts of water released during the
filter replacement.
1 Turn Off the ice maker power switch.
2 Remove the old filter by rotating it counterclockwise (to the left) 90 degrees to release it.
3 Slide the old filter cartridge straight out of
the housing and discard it.
4 Unpackage the new filter cartridge. Slide it
into the filter housing as far as it will go with
the grip end horizontal.
5 Push lightly inward on the filter while rotating
it clockwise (to the right). The filter will then
pull itself inward as it is rotated. Rotate the
filter 90 degrees until it stops and the grip
end is vertical. You may be able to feel a very
light click as the filter locks into place.
6 Press a drinking glass against the water
dispenser while checking for any leaks at
the filter housing. Any spurts and sputters
that occur as the system purges air out of
the dispenser system are normal.
7 Continue dispensing water for 3-4 minutes
or until 1.5 gallons of water has flowed
through the system. You will likely need to
empty and refill your glass several times.
8 Turn On the ice maker.
9 Press and hold the Water Filter reset
button on the control panel for three
seconds. When the display changes from
Red to Green, the status has been reset.
NORMAL OPERATING SOUNDS AND SIGHTS
Understanding the Sounds you
may Hear
Your new, high-efficiency refrigerator may
introduce unfamiliar sounds. These sounds
normally indicate your refrigerator is operating
correctly. Some surfaces on floors, walls, and
kitchen cabinets may make these sounds more
noticeable.
Following is a list of major components in your
refrigerator and the sounds they can cause:
A Evaporator Refrigerant through the
evaporator may create a boiling or
gurgling sound.

NOTE
Energy efficient foam in your refrigerator is
not a sound insulator.

NOTE
During automatic defrost cycle, a red glow
in the back wall vents of your freezer
compartment is normal.
B Evaporator fan You may hear air being
forced through the refrigerator by the
evaporator fan.
C Defrost heater During defrost cycles,
water dripping onto the defrost heater
may cause a hissing or sizzling sound.
After defrosting, a popping sound may
occur.
D Automatic ice maker When ice has
been produced, you will hear ice cubes
falling into the ice bin.
E Electronic control & automatic
defrost control These parts can produce
a snapping or clicking sound when turning
the cooling system on and off.
F Condenser fan You may hear air being
forced through the condenser.
G Compressor Modern, high-efficiency
compressors run much faster than in the
past. The compressor may have a highpitched hum or pulsating sound.
H Water valve Makes a buzzing sound each
time it opens to fill the ice maker.
I Drain pan (not removable) You may hear
water dripping into the drain pan during
the defrost cycle.
J Condenser May create minimal sounds
from forced air.
K Motorized damper May produce a light
humming during operation.
L Ice chute When dispensing ice, you will
hear a snapping or clicking sound when
the solenoid opens and closes the ice
chute.
29
CARE & CLEANING
Protecting your investment
Keeping your refrigerator clean maintains appearance and prevents odor build-up. Wipe up any
spills immediately and clean the freezer and fresh food compartments at least twice a year.
When cleaning, take the following precautions:
•
•
•
•
Never use CHLORIDE or cleaners with bleach to clean stainless steel.
Do not wash any removable parts in a dishwasher.
Always unplug the electrical power cord from the wall outlet before cleaning.
Remove adhesive labels by hand. Do not use razor blades or other sharp instruments which
can scratch the appliance surface.
• Do not remove the serial plate.
Do not use abrasive cleaners such as window sprays, scouring cleansers, brushes, flammable
fluids, cleaning waxes, concentrated detergents, bleaches or cleansers containing petroleum
products on plastic parts, interior doors, gaskets or cabinet liners. Do not use paper towels,
metallic scouring pads, or other abrasive cleaning materials or strong alkaline solutions.

NOTE
If you set your temperature controls to turn off cooling, power to lights and other electrical
components will continue until you unplug the power cord from the wall outlet.
CAUTION
• Pull the refrigerator straight out to move it. Shifting it from side to side may damage
flooring. Be careful not to move the refrigerator beyond the plumbing connections.
• Damp objects stick to cold metal surfaces. Do not touch refrigerated surfaces with wet or
damp hands.
IMPORTANT
If you store or move your refrigerator in freezing temperatures, be sure to completely drain
the water supply system. Failure to do so could result in water leaks when the refrigerator is
put back into service. Contact a service representative to perform this operation.
Vacation and moving tips
Occasion
Short
Vacations
Long
Vacations
Tips
• Leave refrigerator operating during vacations of three weeks or less.
• Use all perishable items from refrigerator compartment.
• Turn automatic ice maker off and empty ice bucket, even if you will only be
gone a few days.
• Remove all food and ice if you will be gone one month or more.
• Turn the cooling system off (see “Controls” section for location of On/Off
button) and disconnect power cord.
• Turn water supply valve to closed position.
• Clean interior thoroughly.
Moving
• Leave both doors open to prevent odors and mold build-up. Block doors open
if necessary.
• Remove all food and ice.
• If using a handcart, load from the side.
• Adjust rollers all the way up to protect them during sliding or moving.
• Pad cabinet to avoid scratching surface.
30
CARE & CLEANING
Care and Cleaning Tips
Part
Cleaning
Agents
Tips and Precautions
Interior &
Door Liners
• Soap and water
• Use two tablespoons of baking soda in one quart of
warm water.
• Baking soda and
water
Door Gaskets • Soap and water
Drawers &
Bins
• Soap and water
Glass
Shelves
• Soap and water
Toe Grille
• Glass cleaner
• Be sure to wring excess water out of sponge or cloth
before cleaning around controls, light bulb or any
electrical part.
• Wipe gaskets with a clean soft cloth.
• Use a soft cloth to clean drawer runners and tracks.
• Do not wash any removable items (bins, drawers, etc.)
in dishwasher.
• Allow glass to warm to room temperature before
immersing in warm water.
• Mild liquid sprays
• Soap and water • Remove toe grille (see Installation Instructions).
• Mild liquid sprays • Vacuum both sides and wipe with sudsy cloth or
sponge. Rinse and dry.
• Vacuum
Exterior &
Handles
• Soap and water
• Non abrasive
glass cleaner
• Do not use commercial household cleaners containing
ammonia, bleach or alcohol to clean handles.
• Use a soft cloth to clean smooth handles.
• Do not use a dry cloth to clean smooth doors.
Exterior &
• Soap and water
Handles
• Stainless steel
(Stainless
cleaners
Steel Models
Only)
• Never use CHLORIDE or cleaners with bleach to clean
stainless steel.
• Clean stainless steel front and handles with nonabrasive soapy water and a dishcloth. Rinse with clean
water and a soft cloth.
• Use a non-abrasive stainless steel cleaner. These
cleaners can be purchased at most home improvement
or major department stores. Always follow
manufacturer’s instruction. Do not use household
cleaners containing ammonia or bleach. NOTE: Always
clean, wipe and dry with grain to prevent scratching.
Replacing
Light Bulbs
• Unplug
refrigerator
• Wash the rest of the cabinet with warm water and
mild liquid detergent. Rinse well and wipe dry with a
clean soft cloth.
• CAUTION: Wear gloves when replacing light bulbs to
avoid getting cut.
• Wear gloves
• Use same wattage when replacing bulb.
• Remove light
cover
• Replace old bulb
• Replace light
cover
• Plug in the
refrigerator
31
CARE & CLEANING
Replacing LED Lights
(select models)
The fresh food compartments of your
refrigerator may have LED lights. Always use
Frigidaire parts for replacement.
To replace LED Lights:
1 Unplug your refrigerator’s power cord.
2 Remove lens cover.
3 Remove LED board.
4 Replace LED board and snap in place
assuring the light is facing in toward the
unit (inside fresh food).
5 Replace lens cover.
Lens Removal
LED Light Board Removal
32

NOTE
LED lights are in series so if one is bad or
unplugged, several lights may not light up.
Ordering Replacement LED Lights
Order new LEDs by calling 877-808-4195,
online at www.frigidaire.com/store, or through
the dealer where you bought the refrigerator.
Here is the product number to request when
ordering:
LED Light, Part #242196201
CARE & CLEANING
Replacing light bulbs
(select models)
Both the freezer and fresh food compartments
of your refrigerator include light bulbs that
will need replacing from time to time. Some
lights have covers that you will need to remove
before replacing the bulbs. Always use bulbs
that are designed for appliance lighting.
Water
Filter
Bulbs
To replace light bulbs:
CAUTION
Wear gloves when replacing light bulbs to
avoid getting cut.
Light Socket
Located Behind
Rear of
Crispers
Crisper Light
Cover
1 Unplug your refrigerator’s power cord.
2 Wear gloves as protection against possible
broken glass.
3 Remove light cover, if necessary.
4 Unscrew and replace old bulb with an
appliance bulb of the same type and
wattage (normally 40 watts).
Light Bulbs
5 Replace light cover, if necessary.
6 Plug in the refrigerator’s power cord.
Light Bulb
Light socket
located behind right
rear of ice container
33
BEFORE YOU CALL
1-800-944-9044 (United States)
1-800-265-8352 (Canada)
CONCERN
CAUSE
AUTOMATIC ICE MAKER
Ice maker is
• Ice maker is turned off.
not making any
ice.
Visit our web site at
www.frigidaire.com
SOLUTION
• Turn on ice maker. For the Frigidaire
Professional ice maker, press and hold the
“ON-OFF” button for three seconds until
the indicator light is on. For the Frigidaire
& Frigidaire Gallery ice maker, lower the
wire signal arm.
• Refrigerator is not
connected to water line
or water valve is not
open.
• Connect the unit to the household water
supply and ensure the water valve is open.
• The water supply line is
kinked.
• Ensure that the supply line does not kink
when the refrigerator is pushed into place
against the wall.
• The water filter is not
seated properly.
• For Frigidaire & Frigidaire Gallery, remove
and re-install the water filter. Be sure to
push the filter firmly so that you hear it
lock solidly into position.
For Frigidaire Professional, remove and
re-install the water filter. Remove by
rotating it counter-clockwise (to the left)
90 degrees to release it. Re-install by
sliding it into the filter housing as far as it
will go with the grip end horizontal. Push
lightly inward on the filter while rotating it
clockwise (to the right). The filter will then
pull itself inward as it is rotated. Rotate the
filter 90 degrees until it stops and the grip
end is vertical. You may be able to feel a
very light click as the filter locks into place.
• The water filter may be
clogged with foreign
material.
• If water dispenses slowly or not at all, or
if the filter is six months old or older, it
should be replaced.
• Freezer ice maker wire
• Move any item or frozen ice cubes that
signal arm is being
may block the signal arm from being in the
held up by an item not
on or down position. See Automatic Ice
allowing it to go in the on
Maker-Freezer section in manual.
or down position. (Does
not apply to Frigidaire
Professional)
34
BEFORE YOU CALL
CONCERN
CAUSE
AUTOMATIC ICE MAKER (Continued)
Ice maker is
• Ice maker is producing
not making
less ice than you expect.
enough ice.
SOLUTION
• The Frigidaire ice maker produces
approximately 4 to 4.5 pounds of ice every
24 hours depending on usage conditions.
The Frigidaire Gallery ice maker
produces approximately 3 to 4 pounds of
ice every 24 hours depending on usage
conditions.
The Frigidaire Professional ice maker
produces approximately 2.5 to 3 pounds
every 24 hours depending on usage
conditions.
• The water filter may be
clogged with foreign
material.
• If water dispenses slower than normal,
or if the filter is six months old or older, it
should be replaced.
• The water supply line is
kinked.
• Ensure that the supply line does not kink
when the refrigerator is pushed into place
against the wall.
• Saddle valve on cold
water pipe is clogged
or restricted by foreign
material.
• Turn off household water line valve.
Remove valve. Ensure that valve is not
a self-piercing saddle valve. Clean valve.
Replace valve if necessary.
• Heavy traffic, opening
or closing of the doors
excessively.
• Press Fast Freeze to temporarily increase
ice production rate. (Does not apply to
Frigidaire Professional.)
• Freezer control is set too
warm.
• Set freezer control to colder setting to
improve performance of the ice maker.
Allow 24 hours for temperature to stabilize.
Ice maker
• Ice maker wire signal arm • Move any item or frozen ice cubes that
will not stop
is being held down by a
may block the signal arm from being in the
making ice
package in the freezer
off or upward position. See Automatic Ice
(select models).
that has fallen against ice
Maker-Freezer section in manual.
maker. (Does not apply to
Frigidaire Professional.)
Ice cubes
• Ice cubes are not being
• Remove ice container and discard ice. The
are freezing
used frequently enough
ice maker will produce fresh supply. Ice
together.
or interruption of power
should be used at least twice weekly to
for prolonged time.
keep the cubes separated.
• Ice cubes are small or
hollow (shells of ice
with water inside). The
hollow cubes break open
in the bin and leak their
water onto existing ice,
which causes it to freeze
together.
• This generally occurs when the ice maker
does not get enough water. This is usually
the result of a clogged water filter or
restricted water supply. Replace the water
filter and if the condition still occurs check
for a Saddle Valve, water valve not turned
on all the way or kinked water supply line.
35
BEFORE YOU CALL
CONCERN
CAUSE
SOLUTION
DISPENSER (Ice & Water)
Dispenser will
• Dispenser lock out is
• Press and hold control lock for three
not dispense
engaged. (Does not apply
seconds.
ice.
to Frigidaire Professional.) • See the “Ice maker is not making any ice”
• There is no ice in the bin
section above.
to be dispensed.
• Be sure the refrigerator doors are
• The refrigerator doors are
not completely closed.
•
• Dispenser paddle has
been pressed too long
and the dispenser motor
has overheated.
Ice dispenser is • Ice has melted and
•
jammed.
frozen around auger
due to infrequent use,
temperature fluctuations,
and/or power outages.
Dispenser will
not dispense
water.
completely closed.
The motor overload protector will reset in
about three minutes and then ice can be
dispensed.
Remove ice container, thaw, and empty the
contents. Clean container, wipe dry, and
replace in proper position. When new ice is
made, dispenser should operate.
• Ice cubes are jammed
• Remove ice cubes that are jamming the
between ice maker and
dispenser.
back of ice container.
• Dispenser lock out is
• Press and hold control lock for three
engaged. (Does not apply
seconds.
to Frigidaire Professional.)
• Water filter not seated
properly.
• For Frigidaire & Frigidaire Gallery, remove
and reinstall the water filter. Be sure to
push the filter firmly so that you hear it
lock solidly into position.
For Frigidaire Professional, remove and
reinstall the water filter. Be sure to press
inward as you rotate it clockwise to lock it
in place.
• Water filter is clogged.
• For Frigidaire & Frigidaire Gallery, replace
filter cartridge. Be sure to remove
protective caps and push the filter firmly so
that you hear it lock solidly into position.
For Frigidaire Professional, replace filter
cartridge. Be sure to press inward as you
rotate it clockwise to lock it in place.
Water has an
odd taste and/
or odor.
36
• Household water line
valve is not open.
• Water has not been
dispensed for an
extended period of time.
• Open household water line valve. See
CONCERN column AUTOMATIC ICE MAKER.
• Draw and discard 10-12 glasses of water to
freshen the supply.
• Unit not properly
connected to cold water
line.
• Connect unit to cold water line that
supplies water to the kitchen faucet.
BEFORE YOU CALL
CONCERN
CAUSE
DISPENSER (Ice & Water) (Continued)
Water pressure • Cut-off and cut-on
is extremely
pressures are too low
low.
(well systems only).
SOLUTION
• Have someone turn up the cut-off and cuton pressure on the water pump
system (well systems only).
• Reverse osmosis system
is in regenerative phase.
• It is normal for a reverse osmosis system
to be below 20 psi during the regenerative
phase.
Water not cold • The water dispensing
• Add ice to cup or container before
enough.
system is not designed to
dispensing water.
chill water.
OPENING/CLOSING OF DOORS/DRAWERS
Door(s) will not • Door was closed too
• Close both doors gently.
close.
hard, causing other door
to open slightly.
• Refrigerator is not level. • Ensure floor is level and solid, and can
It rocks on the floor when
adequately support the refrigerator.
moved slightly.
Contact a carpenter to correct a sagging or
sloping floor.
Drawers are
difficult to
move.
• Refrigerator is touching a • Ensure floor is level and solid, and can
wall or cabinet.
adequately support the refrigerator.
Contact a carpenter to correct a sagging or
sloping floor.
• Food is touching shelf on • Remove top layer of items in drawer.
top of drawer.
• Track that drawers slide
on is dirty.
• Ensure drawer is properly installed on
track.
• Clean drawer, rollers, and track. See Care
& Cleaning.
RUNNING OF REFRIGERATOR
Compressor
• Freezer control is set to
does not run.
“OF” or “0”.
• Refrigerator is in defrost
cycle.
• Set freezer control.
• This is normal for a fully automatic defrost
refrigerator. The defrost cycle occurs
periodically, lasting about 30 minutes.
• Plug at electrical outlet is • Ensure plug is tightly pushed into outlet.
disconnected.
• House fuse blown or
tripped circuit breaker.
• Check/replace fuse with a 15 amp timedelay fuse. Reset circuit breaker.
• Power outage.
• Check house lights. Call local electric
company.
37
BEFORE YOU CALL
CONCERN
CAUSE
SOLUTION
RUNNING OF REFRIGERATOR (Continued)
Refrigerator
• Room or outside weather • It’s normal for the refrigerator to work
runs too much
is hot.
longer under these conditions.
or too long.
• Doors are opened too
• Warm air entering the refrigerator causes it
(Single Speed
frequently or too long.
to run more. Open doors less often.
Compressor)
(Some Models) • Fresh Food/freezer door • Ensure refrigerator is level. Keep food and
may be slightly open.
contains from blocking door. See PROBLEM
column OPENING/CLOSING OF DOORS/
DRAWERS.
• Freezer control is set too
cold.
• Set Fresh Food control to warmer
setting until refrigerator temperature
is satisfactory. Allow 24 hours for
temperature to stabilize.
• Fresh Food/freezer gasket • Clean or change gasket. Leaks in door
is dirty, worn, cracked, or
seal will cause refrigerator to run longer in
poorly fitted.
order to maintain desired temperatures.
• Condenser is dirty.
• Clean condenser. See Care & Cleaning.
Compressor
• Thermostat keeps the
• This is normal. Refrigerator goes on and
goes off and on
refrigerator at a constant
off to keep temperature constant. (Single
frequently.
temperature.
Speed Compressor) (Some Models)
Refrigerator
• Your variable speed
• It is normal for the compressor to run
seems to run
compressor is designed
continuously except during defrost mode.
too much
to run 100% of the time
or too long.
except during the defrost
(Variable Speed
cycle. At times it will run
Compressor)
faster, such as after a
(Some Models)
defrost cycle.
DIGITAL TEMPERATURE DISPLAY
Digital
• Electronic control system • Call your Frigidaire service representative,
temperature
has detected a
who can interpret any messages or number
displays are
performance problem.
codes flashing on the digital displays.
flashing.
WATER/MOISTURE/FROST INSIDE REFRIGERATOR
Moisture collects • Weather is hot and
• The rate of frost buildup and internal
on inside of
humid.
sweating increases.
refrigerator
• Door is slightly open.
• See PROBLEM column OPENING/CLOSING
walls.
OF DOORS/DRAWERS.
Water collects
on bottom
side of drawer
cover.
• Vegetables contain and
give off moisture.
• It is not unusual to have moisture on the
bottom side of the cover.
• Move humidity control (some models) to
lower setting.
Water collects • Washed vegetables and
• Dry items before putting them in the
in bottom of
fruit drain while in the
drawer. Water collecting in bottom of
drawer.
drawer.
drawer is normal.
WATER/MOISTURE/FROST OUTSIDE REFRIGERATOR
Moisture
• Weather is humid.
• This is normal in humid weather. When
collects on
humidity is lower, the moisture should
outside of
disappear.
refrigerator or • Door is slightly open,
• See PROBLEM column OPENING/CLOSING
between doors.
causing cold air from
OF DOORS/DRAWERS.
inside refrigerator to meet
warm air from outside.
38
MAJOR APPLIANCE WARRANTY
Your appliance is covered by a one year limited warranty. For one year from your original date of
purchase, Electrolux will pay all costs for repairing or replacing any parts of this appliance that prove
to be defective in materials or workmanship when such appliance is installed, used and maintained in
accordance with the provided instructions.
Exclusions
This warranty does not cover the following:
1. Products with original serial numbers that have been removed, altered or cannot be readily determined.
2. Product that has been transferred from its original owner to another party or removed outside
the USA or Canada.
3. Rust on the interior or exterior of the unit.
4. Products purchased “as-is” are not covered by this warranty.
5. Food loss due to any refrigerator or freezer failures.
6. Products used in a commercial setting.
7. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances
not in ordinary household use or used other than in accordance with the provided instructions.
8. Service calls to correct the installation of your appliance or to instruct you how to use your appliance.
9. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards,
shelves, etc., which are not a part of the appliance when it is shipped from the factory.
10. Service calls to repair or replace appliance light bulbs, air filters, water filters, other
consumables, or knobs, handles, or other cosmetic parts.
11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry
trip charges, or mileage expense for service calls to remote areas, including the state of Alaska.
12. Damages to the finish of appliance or home incurred during installation, including but not
limited to floors, cabinets, walls, etc.
13. Damages caused by: services performed by unauthorized service companies; use of parts other
than genuine Electrolux parts or parts obtained from persons other than authorized service
companies; or external causes such as abuse, misuse, inadequate power supply, accidents,
fires, or acts of God.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT
REPAIR OR REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES,
INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE
LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE
YEAR. ELECTROLUX SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH
AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS
WRITTEN LIMITED WARRANTY OR ANY IMPLIED WARRANTY. SOME STATES AND PROVINCES DO
NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES,
OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS OR
EXCLUSIONS MAY NOT APPLY TO YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.
If You Need Service
Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty
period should service be required. If service is performed, it is in your best interest to obtain and
keep all receipts. Service under this warranty must be obtained by contacting Electrolux at the
addresses or phone numbers below.
This warranty only applies in the USA and Canada. In the USA, your appliance is warranted by
Electrolux Major Appliances North America, a division of Electrolux Home Products, Inc. In Canada,
your appliance is warranted by Electrolux Canada Corp. Electrolux authorizes no person to change
or add to any obligations under this warranty. Obligations for service and parts under this warranty
must be performed by Electrolux or an authorized service company. Product features or specifications
as described or illustrated are subject to change without notice.
USA
1.800.944.9044
Frigidaire
10200 David Taylor Drive
Charlotte, NC 28262
Canada
1.800.265.8352
Electrolux Canada Corp.
5855 Terry Fox Way
Mississauga, Ontario, Canada
L5V 3E4
39
Download PDF

advertising