Marvel | ML24RDS2NS | Specifications | Marvel ML24RDS2NS Specifications

24” Marvel
Refrigerated Drawers
Model # ML24RD****
Certified to meet
ENERGY STAR® requirements
•D
ynamic Cooling Technology™ delivers rapid cooldown and
the industry’s best temperature stability
• Specially designed for a truly flush fit with adjoining
cabinetry
• MARVEL Intuit™ Integrated Controls provide precise
temperature management from 34°F to 42°F
• Pristine arctic white interior easily wipes clean and efficient
white LED lighting illuminates interior for better viewing
• Insulated thermal-efficient cabinet ensures optimum
efficiency and preservation
• Close Door Assist System™ gently and automatically closes
drawers
• Audible and visual alarms signal when drawer is left ajar to
protect food integrity and energy use
• Vacation/Sabbath mode conserves energy during times
when the unit is not in use and complies with Star-K
requirements
• Height adjustment up to 1” with leveling legs
• 4” black adjustable toe kick
• 1-year warranty
Storage Capacity
Up to (108) 12-oz cans
Product Dimensions
23⅞” W x 33¾” minimum H x 25⅝” D
(including handle)
Finish/Door Options
Ordering Details
Solid Stainless Steel Drawer Front
ML24RDS2NS
Solid Black Drawer Front, Black
Handles
ML24RDS2NB
Solid Panel Ready Drawer Front
ML24RDP2NP
No panel installation kit required.
Stainless Steel
Black
Wood Overlay
(Panel Ready)
Forced
Air Fan
"A"
Evaporator
Plate
"B"
Return
Air Intake
Front
"C"
24" Rough-In Dimensions
PRODUCT
"A"
DIMENSIONS
24”
(61 cm)
"B"
"C"
**34" to 35"
(86.4 to 88.9 cm)
24”
(61 cm)
PRODUCT DATA
MODEL
ELECTRICAL
REQUIREMENTS #
PRODUCT
WEIGHT
ML24RDS
115V/60Hz/15A
130 lbs
(59 kg)
130 lbs
(59 kg)
Cabinet115V/60Hz/15A
Dimensions
ML24RDP
"D"
"E"
"F"
23 7⁄8”
(60.7 cm)
33 3⁄4” to 34 3⁄4”
(85.7 to 88.3 cm)
23 23⁄32”
(60.2 cm)
“G”
“H”
25 21⁄32”
(65.2 cm)
39 5⁄32”
(99.5 cm)
Forced
Air Fan
Evaporator
Plate
Return
Air Intake
Front
Side
"G"
"D"
"F"
Dynamic Cooling Technology™
delivers rapid cool down
and the industry’s best
temperature stability
"E"
The distinctive Marvel design features a
thermal-efficient cabinet and door combined
with Dynamic Cooling Technology™ for
superior temperature stability, faster cooling
1"times and speedy temperature recovery even
(2.5 cm)
with high frequency.
Figure 8
* Depth dimension of rough-in opening may vary depending
on each individual installation. To recess entire drawer "F"
dimension plus 1" (2.5 cm) for thickness
of power cord plug
Width
23 ⅞"
Control Type
is required.
Interior Finish
White
Temperature Range
** Minimum rough-in opening required is to be larger than
Lock
Up to 108 12-oz cans
the adjusted height of the cabinet.
Capacity
Electrical Requirements
Shelving
System 15 amp dedicated NA
# A grounded
circuit is required. Follow
Length of Power Cord
all local building codes when installing electrical and appli-
Shelf
Fronts
ance.
NA
Product Dimensions
Other Storage
NA
Depth to Front of Door
Interior Lighting
Toe Grill Finish
Hinge
Handle
!
WARNING
1 White LED Pod per drawer
Black
NA
Designer
211⁄2"
(54.6 cm)
"H"
Intuit™
34° - 42° F
NA
120V / 60Hz / 15A
5'
Finishes
Yes
Agency Approvals
CSA
ENERGY STAR
Certified
23 ⅞" W x 33 ¾" H x 21 ½" D
23 23/32"
Finishes Key
DepthFloor
to Handle
25 21/32
" installed for freestandmount Anti-tip Bracket must
be
applications.
for5/built
Depthing
with
door at 90° Not required 29
" in applications. SS
32
9
Shipping Weight
160 lbs
SS, B, O
Vacation /
Sabbath Mode
= Stainless Steel
B = Black
O = Overlay
holes from the front, to the recommended diameter of the
handle manufacturer. Counter bore the back-side of the
panel so the screw heads do not interfere with the surface
Overlay
Panels
of the drawer.
Panel thickness
233⁄4"
(603 mm)
13⁄16" (30 mm)
OVERLAY 19"
DRAWER PANEL INSTALLATION
23⁄8"
(60 mm)
(483 mm)
3: Attach the Overlay Panel to the Drawer
1"(25 mm) diameter Step
counter
1. deep
Set the overlay panel on drawer front face and align
bore 1⁄4" (6 mm)
edges. (See Figure 15 below). The custom overlay
2 places, top drawer only.
1429⁄32"
(379 mm)
panel should be flush with the top of the drawer and
centered on the width of the drawer. Clamp panel in
position and mark pilot hole locations. Pick the required
pilot hole size from "Table B" below and drill the pilot
holes ensuring not to drill all the way through the overlay panel.
.35/.31
(9 mm/7.5 mm)
.50
(12.5)
Figure 14
OVERLAY
DRAWER PANEL INSTALLATION
Face
of
Table B: Pilot Hole Drill Sizes for Wood Screws
Overlay Panel
#8 Wood Screw
(This side facing interior) Material Type
1
Figure 13
Hardwood
Step 4: Reinstall the Drawers
⁄8 Diameter Pilot Hole
Softwood
⁄64 Diameter Pilot Hole
7
Step 1.
2: Size
the
Overlay
Panel
Fully
extend
drawer
slides and place drawer on slides.
Cut the overlay
thedrawer
dimensions
below
2. Insert
Be panel
sure to
that
sitsshown
evenly
on inboth slides
andwood
clipsscrews through clearance holes and
Figure 14. On
the
top
drawer
only
drill
the
2
counter-bored
tighten
to
secure overlay panel.
slide into place in rear of drawer.
holes which are clearance for screw heads on the face of
3. Reinstall gasket into channel. Make sure the corners
2.
Re-install
wire
harness
at
rear
corner
of
top
drawer.
the top drawer.
are fully inserted.
3. Re-install two screws through drawer into slides.
This is also a convenient time to locate and drill the holes
ER PANEL
INSTALLATION
for your
handle. Most often the handle is to match that of
the surrounding cabinetry. If your handle attaches from the
back-side of the custom panel, locate the mounting holes
while the panel is attached to the drawer and cabinet. After
Step
Attach
the Overlay
the3:
panel
is removed
from the Panel
drawer, to
drillthe
the Drawer
mounting
1. holes
Set INSTALLATION
the
overlay
paneltoon
drawer
front face diameter
and alignof the
ER PANEL
from
the front,
the
recommended
edges. manufacturer.
(See Figure 15Counter
below). bore
The custom
overlayof the
handle
the back-side
panel so
should
be flush
with do
thenot
topinterfere
of the drawer
and
panel
the screw
heads
with the
surface
centered
on the width of the drawer. Clamp panel in
of
the drawer.
position
and mark
hole locations.
Pick
theDrawer
required
Step
3: Attach
thepilot
Overlay
Panel to
the
Panel
thickness
pilotthe
hole
size from
"Table
B" below
drill
thealign
pilot
1. Set
overlay
panel
on drawer
frontand
face
and
holes ensuring
not to
all the
way
through
the overedges.
(See Figure
15drill
below).
The
custom
overlay
lay panel.
panel
should be flush with the top3 of the drawer and
23 ⁄4"
centered on the width of the drawer.
Clamp panel
in
(603 mm)
13⁄16" (30 mm)
Table
B: Pilot
Hole
Drill
Sizes
Wood Screws
position
and
mark
pilot
holeforlocations.
Pick the required
pilot
hole size
from "Table B"
drill the pilot
Material
Type
#8below
Woodand
Screw
holes ensuring
not to drill1 all the way through the over3
2 ⁄8"
19" Pilot Hole
Hardwood
⁄8 Diameter
lay panel.
(60 mm)
(483 mm)
7
Softwood
⁄64 Diameter Pilot Hole
Table B: Pilot Hole Drill Sizes for Wood
Screws
1"(25 mm)
diameter counter
1
1429⁄32"wood screws through clearance
n
2. Insert
holes
and deep
⁄4" (6 mm)
Material
Type
#8 Woodbore
Screw
(379
mm)
drawer only. PANEL
red
tighten to secure overlayOVERLAY
panel.2 places, top
DRAWER
1
Hardwood
⁄8 Diameter
Pilot the
Hole
of
3. Reinstall
gasket into channel.
Make sure
corners
7
⁄64 Diameter Pilot Hole
are Softwood
fully inserted.
14
Screw clearance
hole through
gasket extrusion
Figure 15a
Overlay panel
flush with top
edge of drawer
Custom overlay
panel to be centered on width of
drawer.
INSTALLATION
Step
4: Reinstall
the
Drawers
nes
2.PANEL
Insert
wood screws
through
clearance
Figure 14holes and
RAWER
INSTALLATION
of
red
the
of
es
After
g
es
he
of
ethe
ace
es
fter
g
he
1. Fully
extend
drawer
slidespanel.
andFace
placeof
drawer on slides.
tighten
to secure
overlay
sure that
drawer
evenly
on both
and clips
3. Be
Reinstall
gasket
intosits
channel.
Make
sureslides
the corners
Overlay
Panel
slide
into
placethe
in rear
of drawer.
are fully
inserted.
(This
side facing
interior)
Step
3:
Attach
Overlay
Panel
to the Drawer
Set the overlay
panel on drawer
front
face and
2. 1.
Re-install
wire harness
at rear
corner
ofalign
top drawer.
edges. (See
15 below).
The drawer
custom overlay
3. Re-install
twoFigure
screws
through
into slides.
ace
elow in
nter-bored
e face of
panel should be flush with the top of the drawer and
centered on the width of the drawer. Clamp panel in
position and mark pilot hole locations. Pick the required
pilot hole size from "Table B" below and drill the pilot
holes ensuring not to drill all the way through the overlay panel.
Figure 15
14
Screw clearance
hole through
gasket extrusion
Using clearance holes in
gasket channel mark
hole locations onto panel
Table B: Pilot Hole Drill Sizes for Wood Screws
Material Type
#8 Wood Screw
Hardwood
1
Softwood
7
⁄8 Diameter Pilot Hole
⁄64 Diameter Pilot Hole
2. Insert wood screws through clearance holes and
tighten to secure overlay panel.
3. Reinstall gasket into channel. Make sure the corners
are fully inserted.
Figure 15a installation instructions,
For comprehensive
please visit www.marvelrefrigeration.com
Overlay panel
Download PDF

advertising