advertisement
▼
Scroll to page 2
of 7
30” Bottom Mount Refrigerator KFN 9855 iDE LI/ KFN 9855 iDE RE Shown: KFN 9855 iDE LI Please note: This information is subject to change 8mieleusa.com Specification Sheets TRS 03282018 30” Bottom Mount Refrigerator KFN 9855 iDE SPECIFICATIONS Overall Unit Dimensions 297/8” (759 mm) W x 7913/16” (2,027 mm) H x 24” (610 mm) D Niche 30 ” (762 mm) W x 80” (2,032 mm) H x 24” (610 mm) D Minimum Niche Opening Dimensions Interior Volume Fresh Food Volume 9.8 cu-ft (277.5 L) Freezer Volume 4.3 cu-ft (127 L) Plumbing Water Supply Requirements Connect to a cold water supply only. Must be connected to a shut-off valve. The water shut-off valve must be accessible after installation. The water pressure must be between 22 psi (1.5 bar) and may not exceed 87 psi (6 bar). If the pressure is higher than 87 psi (6 bar), a pressure reducing valve must be installed. Water Connection Line Unit comes with a male 3/4” BPT connection on back of unit. The connection parts included with the appliance permit the connection of various water lines (included 1/4” compression fitting). Water line is not included. Electrical Electrical Requirements - Volts/Amps 110V / 120V, 60Hz, 15A (single) 110V / 120V, 60Hz, 20A (2 Individual units installed side-by-side, using a Duplex outlet) Power Cord - Plug NEMA 5-15 plug, 6’ 6” (2 m) Custom Panel - Refer to manual for further detail Maximum Refrigerator Door Panel Weight 60 lbs (27 kg) Maximum Freezer Door Panel Weight Each 26.5 lbs (12 kg) Maximum Panel Thickness 3/4” (19 mm) Minimum Panel Thickness 5/8” (16 mm) Shipping Shipping Weight 345 lbs (156.5 kg) Shipping Dimension 325/16” W x 8211/16” H x 291/8” D Support Call Miele (800) 999-1360 Miele Website 8www.mieleusa.com 20/20 Link 82020technologies.com KFN 9855 iDE LI (Left Hinged) Item 38985552CDN KFN 9855 iDE RE (Right Hinged) Item 38985551CDN Hinging is not field reversible. KFN 9855 iDE Page 2 of 7 30” Bottom Mount Refrigerator KFN 9855 iDE Unit Dimensions 29-7/8” (759 mm) 55-1/4” Power Cord exits at the top right when looking at the rear of the unit. KFN 9855 iDE Page 3 of 7 30” Bottom Mount Refrigerator KFN 9855 iDE Niche Dimensions and Water Supply Connection Water Connection • Water line feed-in (D) from left or right above the anit-tipping bracket. • The water line lead-throught for the water supply line (E) is at the bottom right of the appliance. KFN 9855 iDE Page 4 of 7 30” Bottom Mount Refrigerator KFN 9855 iDE Inset Installation Panel Dimensions Stainless steel panels are available as an optional Accessory STAINLESS STEEL PANELS Item# Top Panel 38996045CDN Bottom Panels 38996046CDN Please note following: -Stainless steel panels are not pre-drilled -Handles are sold separately Please take into account the followiong information concerning the cabinet front: - The Panels should be at least 5/8” (16 mm) thick to allow the connecting rails to be fastened to them. - The maximum panel thickness is 3/4” (19 mm). - The refrigerator panel weight must not exceed 60 lbs (27 kg). - Each freezer panel weight must not exceed 26.5 lbs (12 kg) KFN 9855 iDE Page 5 of 7 30” Bottom Mount Refrigerator KFN 9855 iDE Frameless Installation Panel Dimensions Please take into account the followiong information concerning the cabinet front: - The Panels should be at least 5/8” (16 mm) thick to allow the connecting rails to be fastened to them. - The maximum panel thickness is 3/4” (19 mm). - The refrigerator panel weight must not exceed 60 lbs (27 kg). - Each freezer panel weight must not exceed 26.5 lbs (12 kg) KFN 9855 iDE Page 6 of 7 30” Bottom Mount Refrigerator KFN 9855 iDE Door Swing Dimensions KFN 9855 iDE Page 7 of 7 Specification Sheets TRS 03282018
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project