GE Monogram | ZIBI240HII | Quick Specs | GE Monogram ZIBI240HII Quick Specs

MONOGRAM BAR REFRIGERATOR WITH ICEMAKER
ZIBI240HII
OVERALL DIMENSIONS
23 5/8" (60.0)
34 1/4"
(87.0)
FRONT VIEW
24 1/2" (61.6)
21 3/4" (54.8)
SPECIFICATIONS
Overall Width
23 5/8" (60.0 cm)
Overall Height
34 1/8" (86.7 cm)
Overall Depth
23 1/4" (59.1 cm)
Door Clearance
8 3/8" (21.3 cm) @ 110°
1/2" (1.3 cm) @ 90°
25 1/8" (63.8) door
length
Overall Capacity
4.25 cu. ft.
Minimum Cabinet
Width
23 3/4" (60.3 cm)
Minimum Cabinet
Depth
24" (61.0 cm)
Cutout Width
23 3/4" (60.3 cm)
Cutout Height
34 1/2" (87.6 cm) Min
35" (88.9 cm) Max
Electrical
Requirements
2.0 A
Voltz/Hertz/Amps
120 V, 60 Hz,
15 or 20 amp circuit
Shipping Weight
SIDE VIEW
23 5/8" (60.0)
8 3/8"
(21.3)
126 lb (57 kg)
1/4"
(0.6)
ATTENTION ELECTRICIAN:
A 115 volt 60Hz., 15 or 20 amp power
supply is required. An individual properly
grounded branch circuit or circuit breaker
is recommended. Install a properly
grounded 3-prong electrical receptacle
recessed into the back wall.
Dimensions in
parentheses are in
centimeters unless
otherwise noted.
Actual product
dimension may
vary due to
manufacturing
tolerances.
TOP VIEW
(SHOWING
DOOR SWING)
25 1/8"
(63.8)
Product Specification Revised 7/17
ZIBI240PII
MONOGRAM BAR REFRIGERATOR
WITH ICEMAKER
NOTES
INSTALLATION
Installation Space: This module
can be installed beneath a
countertop or can be used freestanding.
24" (61.0)
min cutout depth
For a standard installation of
stainless steel unit: The product
must be installed so that the
front face will project 1-5/8"
forward of adjacent cabinets.
23 3/4" (60.3)
min standard
24 3/4" (62.9)
min flush inset
34 1/2"
(87.6) min
underside of
counter to floor
35" (88.9) max
10 1/2" (26.7)
ELECTRIC/
WATER
9"
(22.9) max
1 1/2" (3.8)
CUTOUT INSTALLATION
SIDE VIEW
INSTALLATION CUTOUT
FRONT VIEW
23 3/4" min.
Trim
24 3/4" min. width
stainless steel models
.10" Spacer Panel
(bb)
Front Edge of
Product Case
Dim. A
In a standard installation, the
product will project forward of
adjacent cabinets. See Dim. A.
Flush
3/4"
Overlay
Installation
Dim. A
Panel
Filler panel or cleat to be set
back even with front of case.
CABINET
CABINET
Front Edge of
Product Case
CABINET
110º
Front Face
110º
Front Face
• Do not install these products
where the temperatures will
go below 55° F (13 C) or above
90° F (32 C).
See installation instructions for
side-by-side information.
Door
1/4" Backer Panel
B"
Location Requirements: All
Monogram Refrigeration
Modules may be closed in on
the top and sides as long as
the front is unobstructed for air
circulation and door swing.
• These products are not
designed to be stacked one
over the other.
A" (aa)
Standard
Installation
For a flush installation of
stainless steel unit: Install a
1" wide filler strip on the hinge
side. The width of the opening
must be 24-3/4" min. wide.
See installation instructions for
details.
• Products must operate from
separate properly grounded
receptacles.
REFRIGERATION MODULES, TOP VIEW
CABINET
ZIBI240HII
These products will fit flush to adjacent
cabinets when installed with a Dim. A - width
filler panel or cleat. The filler panel should be
recessed or set back behind the door and
even with the front edge of the product case.
120º
120º
PRODUCT
DIM. A
PRODUCT
DIM. A
ZDWI240, ZDB1240
2"
ZDWI240, ZDB1240
1"
ZDWR240, ZDBR240
1-3/4"
ZDWR240, ZDBR240
1"
ZIFS240, ZIF1240
1-5/8"
ZIB1240, ZIF1240
1"
ZDOD240
1-7/8"
ZIFS240, ZIBS240
1/4"
ZIB1240, ZIBS240
2-5/8"
ZDOD240
1-1/4"
Product Specification Revised 7/17
MONOGRAM BAR REFRIGERATOR WITH ICEMAKER
NOTES
3/4" OVERLAY PANEL DIMENSIONS
(IN INCHES)
A (WIDTH)
B (HEIGHT)
1/4" Backer
23 3/16"
29 9/16"
.10" Spacer
22 1/2"
29 1/16"
3/4" Overlay
23 5/8"
30"
ZIBI240HII
Assemble overlay panels with
glue and screws
Center spacer panel on the
backer panel, left to right and
top to bottom. Secure the
panels with glue.
Center the spacer/bracket
panel on the overlay panel.
Secure with glue and screws.
Countersink screws into the
backer panel.
Note: Max assembled drawer panel wight is 25 lbs.
3/4"
Max. assembled door panel
weight is 25 lbs.
7/8"
3/8"
Backer side of
custom panel
7/8"
3/4"
The overlay panel must be
secured to a 1/4"-thick backer
panel which slides into the trim.
A .10"-thick spacer panel must
be placed between the custom
and backer panel.
3/8"
Use a 3/4" router bit to cut a
notch into the back side of the
assembled panel to allow for
hinge clearance.
A custom handle of your choice,
supplied by your cabinetmaker,
must be installed on this overlay
panel. Countersink all screws
into the backer panel. Screws
cannot protrude from the
backer panel.
Overlay Panel
Spacer Panel
Backer Panel
Product Specification Revised 7/17
MONOGRAM BAR REFRIGERATOR WITH ICEMAKER
ZIBI240HII
FEATURES AND BENEFITS
DIGITAL TOUCH CONTROLS
Provide precise temperature settings for cooling
all types of fresh foods and beverages, and a LED
display allows easy viewing of temperatures
AUTOMATIC ICEMAKER WITH REMOVABLE
ICE BIN
Makes up to 8 pounds of ice per day
SPACIOUS INTERIOR WITH REMOVABLE
SPILLPROOF GLASS SHELVES AND FULLEXTENSION WINE RACKS
Accommodates beverages and fresh foods of all
types and sizes, and puts them all within easy reach
SOFT INTERIOR LED LIGHTING
Automatically illuminates when the door is open,
but can be activated by an internal on/off switch
CONVENIENT 24" CONFIGURATION
Is fully finished on all sides to allow installation
virtually anywhere in the home
FLUSH INSET INSTALLATION CAPABLE
Allows near-seamless integration with surrounding
cabinetry
CUSTOM-PANEL READY
Lets you coordinate models with cabinetry for
a look of elegant understatement. Customer
must choose a custom door panel and handle to
complement their décor
R
Product Specification Revised 7/17
Download PDF

advertising