RCS RWD1 Manual
RCS Warming Drawer
Instruction Manual
Model Number: RWD1 36"
Electric Warming Drawer
Rated 120V, 60 Hz, 8A
Electrical: 120 Volt, 60 Hz, AC Only 15- or 20- amp.
Use copper wire only.
A time-delay or circuit breaker and
separate circuit is recommended.
TABLE OF CONTENTS
PAGE #
SAFETY INSTRUCTIONS………………………………………………………………………………………………………………………… 2
INSTALLATION INSTRUCTIONS…………………………………………………………………………………………………………….. 3
OPERATING INSTRUCTIONS…………………………………………………………………………………………………………………. 4
CLEANING & MAINTENANCE……………………………………………………………………………………………………………….. 5
TROUBLESHOOTING GUIDE………………………………………………………………………………………………………………… 5
PARTS LIST…………………………………………………………………………………………………………………………………………… 6
WARRANTY………………………………………………………………………………………………………………………………………….. 6
READ THE FOLLOWING INSTRUCTIONS CAREFULLY AND BE SURE YOUR WARMING DRAWER IS
PROPERLY INSTALLED, ASSEMBLED AND CARED FOR. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY
RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE, IF YOU HAVE QUESTIONS
CONCERNING ASSEMBLY OR OPERATION, CONSULT YOUR DEALER OR APPLIANCE SERVICE
REPRESENTATIVE.
NOTE TO INSTALLER:
LEAVE THESE INSTRUCTIONS WITH THE CONSUMER AFTER INSTALLATION.
NOTE TO THE CONSUMER:
RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
THIS OUTDOOR COOKING ELECTRIC APPLIANCE IS NOT INTENDED TO BE INSTALLED IN OR ON
RECREATIONAL VEHICLES AND/OR BOATS.
SAFETY INSTRUCTIONS
Read carefully before operating your warming drawer
Electrical Requirements
Important: Observe all governing
codes and ordinances.
It is the customer's responsibility:
To contact a qualified electrical installer.
To assure that the electrical installation is adequate
and in conformance with National Electrical Code.
ANSUNFPA 70 — latest edition* or
CAN/CSA-C22.2 No. 0-M91
CANICSA-022.2 No. 0.4-04
CANSCSA-C22 2 No. No. 64-M91
UL 1026, 5Th Edition
and all local codes and ordinances.
You must have:
 120-volt, 60Hz, AC-only. 15- or 'Hamp., fused electrical supply,
 Outlet located in the cabinet as close as
possible to the warming oven.
We recommend:
 A time-delay fuse or circuit breaker

a separate circuit serving this appliance
only.
If codes permit and a separate ground wire is used,
it is recommended that a qualified electrician
determine that the ground path is adequate.
Copies of the standards listed may be obtained
from:
*National Fire Protection Association
1 Batterymarch Park Quincy, Massachusetts
02169-7471
** Canadian Electrical Association
175 Rexdale Boulevard
For your personal safety, this appliance
must be grounded. This appliance is
equipped with a power supply cord having
3-prong ground plug. To minimize possible
shock hazard, the cord must be plugged
into a mating 3-prong ground-type outlet
grounded in accordance with local codes
and ordinances. See Figure 1. If a grounded
outlet is not available, it is the personal
responsibility and obligation of the
customer to have a properly grounded 3prong outlet, installed by a qualified
electrician.
Warning — Improper connection of the
equipment-grounding conductor can result
in a risk of electric shock. Check with a
qualified electrician or serviceman if you
are in doubt as to whether the appliance is
properly grounded Do not modify the plug
provided with the appliance - If it will not
fit the outlet, have a proper outlet
installed by a qualified electrician.
Important Safety Instructions
WARNING:
To reduce the risk of fire, electrical shock,
injury to persons, or damage when using the warming drawer,
follow basic precautions, including the following:
 Proper Installation — Be sure the warming drawer is properly
installed and grounded by a qualified technician.
 Do Not Leave Children Alone — Children should not be left alone or
unattended in area where warming drawer is in use. They
should never be allowed to lie, sit or stand on any part of the
warming drawer.
 Wear Proper Apparel — Loose-fitting or hanging garments
should never be worn while using the warming drawer.
 User Servicing — Do not repair or replace any part of the warming
drawer unless specifically recommended in the manual. All other
servicing should be referred to a qualified technician.
Use Only Dry Potholders — Moist or damp potholders on hot surfaces
may result in burns from steam. Do not let potholder touch hot
heating elements. Do not use a towel or other bulky cloth.
 Do Not Heat Unopened Food Containers — Build-up of pressure may
cause container to burst and result in injury.
 DO NOT TOUCH HEATING ELEMENTS OR INTERIOR SURFACES
OF WARMING DRAWER — Heating elements may be hot even
though they are dark in color. Interior surfaces of a warming
drawer become hot enough to cause burns. During and after use,
do not touch, or let clothing or other flammable materials contact
heating elements or interior surfaces of warming drawer until they
have had sufficient time to cool. Other surfaces of the warming
drawer may become hot enough to cause burns —among these surfaces
the warming drawer vent openings and surfaces near these
openings and warming drawer doors.
 Storage in Warming Drawer— Flammable materials should not be
stored in a warming drawer.
 Do Not Use Water on Grease Fires — Smother fire or flame or
use dry chemical or foam-type extinguisher.
 Use Care When Opening Drawer — Let hot air or steam escape
before removing or replacing food.
*SAVE THESE INSTRUCTIONS
2
INSTALLATION INSTRUCTIONS
Island Installation
1) Provide a 10 1/8" H x 34 1/2" W x 21" D cutout to the front of the island.
2) Provide support beams using metal studs.
3) Pull the drawer out of the drawer casing to gain access to the mounting holder at the front of the
casing.
4) Insert the drawer casing into the island opening.
5) Secure the drawer casing with screws at the inside front top and bottom, using the pre-punched
mounting holes.
6) Re-assemble the drawer section into the drawer casing.
7) Apply weather-proof sealant along the edges of the warmer. (Not Included)
8) Plug-in the warmer to a properly grounded, weather-proof, electrical outlet.
IMPORTANT
- Be sure that the warming drawer is properly grounded and installed by a qualified technician. The
electrical cord has a 3 prong plug. Do not cut any of the prongs.
- Make sure that the island is free of cracks that would allow water or other liquids to get into the
electrical controls.
- Keep the warming drawer away from water sprinklers.
3
OPERATING INSTRUCTIONS
Temperature Controls
The temperature control dial is used to select the temperature of the warming drawer. It is located on the right
hand side of the control panel and has dial settings from 50°F-230°F.
The warming drawer should only be opened when adding or removing food. Continuous opening of the
drawer allows warm air to escape and make the food colder.
Do not use aluminum foil to line the drawer. Foil is an excellent heat Insulator and will trap heat beneath it.
This may affect the performance of the warming drawer, the Interior finish and possibly be a safety issue.
Heat-On Light
The heat-on light is located above the temperature control knob. The red light turns on when the control knob
is set and cycles "on" and "off" with the heating element as temperature is maintained.
Moisture Vent Control
The moisture vent control is located at the top inside of the warming drawer, it can be adjusted In any position
between "open' and "close" to maintain desired degree of moisture.
For crispy foods, slide the moisture vent control inward to open the vents and allow the moisture to escape.
For moist food, side the moisture vent control outward to close the vents and seal the moisture inside the
drawer.
Heating Instructions
1. Dry Heat
a) The main function of the warming drawer is to hold hot cooked foods at serving temperature.
b) For crispy foods, slide the moisture vent control inward to open the vents and allow the moisture to
escape.
c) Set the temperature control dial, Heat-on light will appear until the desired temperature is reached.
2. Moist Heat
a) The warming drawer also seals moisture within the drawer to keep the food moist.
b) Put just enough water, approximately 1/2” high, in the steam pans. (Not Included)
c) Place the steam rack inside the steam pan. (Not Included)
d) Place the food directly on the rack or use a suitable container that will fit in the steam pans. Do not use
plastic containers or utensils.
e) Slide the moisture vent control outward to close the vents and seal the moisture inside the drawer.
f) Set the temperature control dial. Heat-on light will appear until the desired temperature is reached.
g) Periodically, check the water level in the steam pans and add water when necessary.
3. Proofing Yeast Dough
a) Yeast dough can be proofed in a warming drawer.
b) Place the dough in a bowl and turn the temperature control at the lowest setting, to facilitate the
fermentation process.
c) Place a towel over the dough to minimize surface drying.
d) Let the dough remain in the warming drawer until it has doubled in size and a slight depression remains
when the surface is touched gently with a finger.
4
CLEANING & MAINTENANCE
The Warming Drawer is made of welded #304 stainless steel.
1. Allow the warming drawer and its accessories to cool before cleaning.
2. Clean all items including the drawer with the mildest cleanser. Scrub dirt with sponge.
3. When cleaning the front panel, always scrub in the direction of the grain. In order to maintain
the luster and highlights of polished surface, do not use abrasives when cleaning polished
surfaces. Use the mildest cleaner.
4. Do not use steel wool to clean the drawer and accessories.
5. Check out the slide rails and make sure they are clean and free from debris.
6. It is highly recommended to clean the warming drawer after every use.
TROUBLESHOOTING GUIDE
Problem
1. Warming Drawer will not heat up
2. Heat-light will not come on
What To Do
1. Check if the unit is plugged in to an
electrical outlet.
2. Check if the temperature control dial
is set properly.
3. Check if the circuit breaker is open.
1. If service is required:
1. Call your dealer.
2. Provide the following info
- Model Number
- Serial Number
- Date Purchased
- Name of dealer where the unit was
purchased from
5
PARTS LIST & WARRANTY
Model Number: RWD1
36" Electric Warming Drawer, Rated 120V, 60 Hz, 8A
1) Heating Element
6) Roller Guides
2) Thermostat
7) Drawer Handle
3) Chrome Bezel
8) Handle Bracket
4) Heat on Light
9) Drawer
5) Control Knob
10) Steam Pan Guide
HOW TO ORDER REPLACEMENT PARTS
Please refer to the parts list on this page.
To make sure you obtain the correct replacement parts for your warming drawer, the following information is
required to assure getting the correct part.
1. Model number (see data sticker on unit)
2. Reference number of replacement part needed.
3. Description of replacement part needed
4. Quantity of parts needed.
IMPORTANT: Use only factory authorized parts. The use of any part that is not factory authorized can be
dangerous. This will also void your warranty.
IMPORTANT: Keep this operating instruction manual for referral and for replacement parts ordering.
WARRANTY
MODEL Number: RWD1
36" Electric Warming Drawer, Rated 120V, 60 Hz, 8A
Limited Lifetime on all construction and workmanship, and 1 year on electrical/parts.
RCS Gas Grills 1-800-833-5998 RCSGasGrills.com
V3.23.17
6
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising