Smeg | C36GGXU | Conversion Kit Installation | Smeg C36GGXU Conversion Kit Installation

Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS
WARNING: If the instructions contained in this manual are not followed
precisely, fire or explosion may result causing property damage, personal
injury or loss of life.
- Do not store or use gasoline or other flammable vapors or liquids near this
or any other appliance.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switches.
• Do not use any telephones in your building.
• Immediately call your gas supplier from a neighbor’s phone. Follow the gas
supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
- Installation and service must be performed by a qualified installer, service
company or gas supplier.
READ AND SAVE THESE INSTRUCTIONS - Your safety and the safety of others are very important.
We have provided many important safety messages throughout this manual and on the appliance.
Read all the instructions before using the appliance and always obey all safety messages.
RECOGNIZE SAFETY INFORMATION
This is a safety alert symbol. This symbol alerts you to potential hazards that can result in severe
personal injury or loss of life.
UNDERSTAND SIGNAL WORDS
A signal word - DANGER, WARNING or CAUTION - is used with the safety alert symbol. DANGER
denotes the most serious hazards. It means you could lose your life or be seriously injured if you do not
immediately follow the instructions. WARNING means you could lose your life or be seriously injured if
the instructions are not followed. CAUTION indicates a potentially hazardous situation which, if not
avoided, could result in minor to moderate injury.
3
Important Safety Instructions
The safety messages will inform you of potential hazards, on how to avoid the risk of injury and what can
occur if the instructions are not followed.
IMPORTANT: Observe all governing codes and ordinances.
WARNING: For your safety, the instructions contained in this manual must be followed to
minimize the risk of fire or explosion and to prevent property damage, personal injury or loss of
life.
-
This conversion kit must be installed by a qualified service agency in accordance with the
manufacturer's instructions and all applicable codes and requirements of the authority having
jurisdiction.
-
If the information in these instructions is not followed exactly, a fire, an explosion or
production of carbon monoxide may result causing property damage, personal injury or loss
of life.
-
The qualified service agency is responsible for the proper installation of this kit. The
Installation is not proper and complete until the operation of the converted appliance is
checked as specified in the manufacturer’s instructions supplied with the kit.
Installation shall not be considered correct and complete until the operation of the converted
appliance is checked as specified in the manufacturer's instructions supplied with this kit.
FIRE HAZARD
WARNING
Securely tighten all gas connections. lf connected to LP, have a qualified
technician ensure that the gas pressure does not exceed a 14” W.C.P.
Examples of qualified technicians include licensed heating personnel,
authorized gas company personnel and authorized service personnel.
FAILURE TO DO SO CAN RESULT IN LOSS OF LIFE, EXPLOSION, OR FIRE.
Caution: Before proceeding with the conversion, the gas supply must be shut off prior to
disconnecting the electrical power.
4
Conversion Kit
Check that the main gas supply line to the range is shut off and that the
power supply cord is disconnected.
1)
2)
Remove access cap “A” by using a screwdriver or a coin, turning the access cap counterclockwise.
The gas pressure regulator has two settings which are indicated on two sides of the cap. Turn the cap
and reinstall it in the regulator with "LP" visible from the outside of the regulator.
Incoming line pressure upstream from the
regulator must be 1” (2.5 cm) W.C.P. higher than
the manifold pressure in order to check the
regulator. Incoming line pressure to the regulator
should be as follows for operation and checking
the regulator setting:
- NATURAL GAS: Set pressure to 4” W.C.P.
Incoming line pressure of 3 1/2” - 10 1/2” W.C.P
maximum;
- LP GAS: Set pressure to 11” W.C.P. Incoming
line pressure 8”- 13” W.C.P. maximum.
The range must be isolated from the gas supply piping system by turning off the respective manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or
greater than 1/2 psig (3.5 kPa).
Replacing the rangetop's burners nozzles (This operation does not require primary air regulation).
1 Remove the grates and all the burner caps and heads;
2 Unscrew the burner nozzles with a 7 mm socket wrench;
3 Replace the nozzles according to the type of gas to be used and the description in paragraph 3.2
“Burner and nozzle characteristics table”.
4 Put the burners back in their correct position.
3)
5
Conversion Kit
Replacing the oven's burners nozzles (This operation does not require primary air regulation).
C24GGXU (23 15/16 ” - 608 mm)
1) Oven burner: Open the oven door and remove any accessories that are inside.
2) Lift up the oven surface and pull it outwards.
3) Loosen the screws A and B.
4)
4) Move away the lock that secures the thermocouple and igniter to the burner with screw A.
5) Slide the burner outwards until the nozzle is accessible.
6) Replace the nozzle using a 7mm socket wrench.
1) Broil burner: Open the oven door and remove any accessories that are inside.
2) Loosen the screw B.
3) Slide the burner outwards until the nozzle is accessible.
4) Replace the nozzle using a 7mm socket wrench.
6
Conversion Kit
Replacing the oven's burners nozzles (This operation does not require primary air regulation).
C36GGXU (35 3/4 ” - 908 mm)
1) Oven burner: Open the oven door and remove any accessories that are inside.
2) Unscrew the two fastening screws before
removing the oven floor.
3) Lift the oven floor and slide it out.
5)
4) Unscrew the burner's fastening screw.
5) Remove the burner from its place by
sliding it out and moving it to the side.
(Make sure not to damage the
thermocouple or the spark electrode
during this operation).
7
Conversion Kit
6) Using a 7mm socket wrench replace the
nozzle, installing the one that is
appropriate for the type of gas to be used.
Refer to the gas charts at point 5.
7) WARNING: The tightening torque of the
nozzle must be equal to 4 Nm.
After replacing the nozzle, put the burner back
in its place. (Make sure not to damage the
thermocouple or the spark electrode during
this operation).
8) Screw in the burner's fastening screw.
9) Reposition the oven floor making sure to insert it correctly. The floor must be perfectly level.
10) Screw in the two fastening screws after having repositioned the oven floor.
8
Conversion Kit
1) Broil burner: Open the oven door and remove any accessories that are inside.
2) Unscrew the two fastening screws for the
burner.
3) Remove the burner by sliding it from its
place and reposition it as shown in the
picture. (Make sure not to damage the
thermocouples and the spark electrode).
4) Using a 13mm socket wrench replace the
nozzle, installing the one that is appropriate
for the type of gas to be used. Refer to the
gas charts at point 5.
5) WARNING: The tightening torque of the
nozzle must be equal to 4 Nm - 14.4 Ozf.
Correctly reposition the burner in its place and
screw in the two fastening screws.
9
Conversion Kit
6)
To adjust the range for LP gas or to return to Natural Gas use, refer to the charts below.
C24GGXU (23 15/16 ” - 608 mm)
Natural gas
Qt
Injector
Qr
BTU
Ø mm
BTU
Front Right
6200
1.20
1500
Front Left
6200
1.20
1500
Rear Left
3400
0.90
1200
0.80
1000
1.65
2000
Rear Right
Inner
Outer
14400
Oven
11500
1.60
3000
Broiler
11000
1.55
-
Qt
Injector
Qr
By-pass
BTU
Ø mm
BTU
mm
Front Right
6200
0.72
1500
0.39
Front Left
6200
0.72
1500
0.39
Rear Left
3400
0.54
1200
0.33
0.46
1000
0.30
0.94
2000
0.60
LP
Rear Right
Inner
Outer
14400
Oven
11500
0.94
3000
0.52
Broiler
11000
0.93
-
-
NOTE: Save the nozzles that were removed from the appliance along with these instructions for possible
future use.
10
Conversion Kit
C36GGXU (35 3/4 ” - 908 mm)
Natural gas
Qt
Injector
Qr
BTU
Ø mm
BTU
Front Right
6200
1.20
1500
Front Center
3400
0.90
1200
Front Left
6200
1.20
1500
Rear Left
3400
0.90
1200
0.80
1000
1.65
2000
Rear Center
Inner
Outer
14400
Rear Right
10000
1.52
2500
Oven
16900
2.15
4600
Broiler
16900
2.15
-
Qt
Injector
Qr
By-pass
BTU
Ø mm
BTU
mm
Front Right
6200
0.72
1500
0.39
Front Center
3400
0.54
1200
0.33
Front Left
6200
0.72
1500
0.39
Rear Left
3400
0.54
1200
0.33
0.46
1000
0.30
0.94
2000
0.60
LP
Rear Center
Inner
Outer
14400
Rear Right
10000
0.90
2500
0.45
Oven
16900
1.20
4600
0.68
Broiler
16900
1.20
-
-
NOTE: Save the nozzles that were removed from the appliance along with these instructions for possible
future use.
FIRE HAZARD
WARNING
Use a soapy solution to check that it is leak-tight.
Never test for gas leaks with a match or other flames.
Failure to follow this instruction can result in loss of life or fire
11
Conversion Kit
7)
Follow these instructions to leak test the appliance:
Use a brush and liquid detergent to test all gas connections for leaks. Bubbles around connections
indicate a leak. If a leak appears, shut off the gas valve controls and adjust the connections. Then check
the connections again. Remove all the detergent product from the range. Replace the parts on the
burner and turn the knobs on the gas tap pins.
NEVER TEST FOR GAS LEAKS WITH A MATCH OR OTHER FLAMES.
8)
Check that the flame at the maximum flame position has a blue color. It should be clean and soft in
character. No blowing or lifting of flame should occur. Occasional orange flashes are normal and reflect
different elements in the air or gas.
Minimum adjustment for Natural Gas
Cooking Hob: Light the burner and turn the knob to the minimum
position
. Remove the gas tap knob and turn the adjustment screw
at the side of the tap rod until the desired minimum flame is achieved.
Refit the knob and verify that the burner flame is stable (when turning
the knob rapidly from the maximum to the minimum position the flame
must not go out).
Repeat this operation on the remaining gas taps on the hob.
9)
Oven: Light the burner and turn it to the maximum temperature for at
least 10 minutes. Then, turn the knob to the minimum position (LOW).
Remove the knob and, using a screwdriver, locate the adjustment
screw alongside of the tap rod (as shown in the figure). Turn the
adjustment screw until the desired minimum flame is achieved.
Refit the knob and verify that the burner flame is stable (when turning
the knob rapidly from the maximum to the minimum position the flame
must not go out).
Moreover, check that the flame does not go out when the door is being
openend or closed.
10)
Minimum adjustment for LP Gas
Turn off the burners and unplug the appliance from the electrical power supply.
For regulating the minimum with LP, the screws at the side of the tap rod must be turned clockwise all the
way. Once the regulation has been completed, replace the seal on the by-passes using paint or similar
materials. Follow the instructions given in point 9 to locate the adjustment screws.
11)
Completely fill out the conversion label (part no. 92849A078) and attach it to the rear of the appliance.
Do not cover any other labels with the conversion label.
12)
At higher altitudes, no further adjustments are necessary. Derating the burners is also unnecessary.
NATURAL GAS:
To convert back to Natural Gas: Follow steps 1 through 9 and replace the nozzles in the order in which
they were removed.
12
Download PDF

advertising