Viking | VGR5606GQSS | Installation Instruction | Viking VGR5606GQSS Installation Instruction

Installation
Professional Freestanding Ranges
Table of Contents
Warnings & Important Safety Instructions ______________________________________________3
Dimensions ________________________________________________________________________6
Specifications ______________________________________________________________________8
Clearance Dimensions (Proximity to Cabinet __________________________________________10
Clearance Dimensions (Wood/Composite Overlay) ____________________________________11
Electrical & Gas Requirements ______________________________________________________12
General Information________________________________________________________________14
Installation ________________________________________________________________________15
Door Removal ________________________________________________________________15
Leg Installation ________________________________________________________________16
Leveling/Adjustments/Alignment ________________________________________________16
Anti-tip Device Installation ______________________________________________________18
Connecting Gas & Electric ______________________________________________________19
Standoff Spacer Removal ______________________________________________________20
Final Installation________________________________________________________________20
Door Replacement ____________________________________________________________21
Final Preparation __________________________________________________________________22
Performance Checklist______________________________________________________________22
Service & Registration ______________________________________________________________23
2
IMPORTANT–
Read and Follow!
• Before beginning, please read these
instructions completely and carefully.
Your safety and the safety of others is
very important.
We have provided many important safety
messages in this manual and on your
appliance. ALWAYS read and obey all
safety messages.
• DO NOT remove permanently affixed
labels, warnings, or plates from product.
This may void the warranty.
This is the safety alert symbol. This
symbol alerts you to hazards that
can kill or hurt you and others.
• All local and national codes and ordinances
must be observed. Installation must
conform with local codes or in the absence
of codes, the National Fuel Gas Code ANSI
Z223.1 INFPA54.
All safety messages will be preceded by
the safety alert symbol and the word
“DANGER,” “WARNING” or “CAUTION.”
These words mean:
• The installer must leave these instructions
with the consumer who should retain for
local inspector’s use and for future
reference.
DANGER
Hazards or unsafe practices
which WILL result in severe personal injury or
death.
In Canada: Installation must be in accordance
with the current CAN/CGA B149.1 & 2 Gas
Installation codes and/or local codes. Electrical
installation must be in accordance with the
current CSA C22.1 Canadian Electrical Codes
Part 1 and/or local codes.
WARNING
Hazards or unsafe practices
which COULD result in severe personal injury or
death.
CAUTION
In Massachusetts: All gas products must be
installed by a “Massachusetts” licensed
plumber or gasfitter. A “T” type handle
manual valve must be installed in the gas
supply line to the appliance.
Hazards or unsafe practices which COULD result
in minor personal injury or property damage.
All safety messages will identify the
hazard, tell you how to reduce the chance
of injury, and tell you what can happen if
the instructions are not followed.
An air curtain or other overhead range hood
which operates by blowing a downward
airflow onto the range, shall not be used with
a gas range
3
IMPORTANT–
Read and Follow!
A GFI shall be used if required by NFPA-70 (National Electric Code), federal/state/local
laws, or local ordinances.
• The required use of a GFI is normally related to the location of a receptacle with respect to
any significant sources of water or moisture.
• Viking Range, LLC will NOT warranty any problems resulting from GFI outlets which are not
installed properly or do not meet the requirements below.
If
•
•
•
•
the use of a GFI is required, it should be:
Of the receptacle type (breaker type or portable type NOT recommended)
Used with permanent wiring only (temporary or portable wiring NOT recommended)
On a dedicated circuit (no other receptacles, switches or loads in the circuit)
Connected to a standard breaker of appropriate size (GFI breaker of the same size NOT
recommended)
• Rated for Class A (5 mA +/- 1 mA trip current) as per UL 943 standard
• In good condition and free from any loose-fitting gaskets (if applicable in outdoor situations)
• Protected from moisture (water, steam, high humidity) as much as reasonably possible
WARNING
DANGER
To prevent possible damage to cabinets and
cabinet finishes, use only materials and finishes
that will not discolor or delaminate and will
withstand temperatures up to 194°F (90°C).
Heat resistant adhesive must be used if the
product is to be installed in laminated
cabinetry. Check with your builder or cabinet
supplier to make sure that the materials meet
these requirements.
FIRE/EXPLOSION HAZARD
IF THE INFORMATION IN THIS
MANUAL IS NOT FOLLOWED EXACTLY, A
FIRE OR EXPLOSION MAY RESULT CAUSING
PROPERTY DAMAGE, PERSONAL INJURY, OR
DEATH.
• DO NOT store or use gasoline or other
flammable vapors and liquids in the vicinity of
this or any other appliance.
• WHAT TO DO IF YOU SMELL GAS:
–DO NOT try to light any appliance.
–DO NOT touch any electrical switch;
DO NOT use any phone in your building.
–Immediately call your gas supplier from a
neighbor’s phone.
–Follow the gas supplier’s instructions.
–If you cannot reach your gas supplier, call
the fire department.
• Installation and service must be performed by
a qualified installer, service agency, or the gas
supplier.
CAUTION
This appliance is not to be used by persons
(including children) with reduced physical,
sensory or mental capabilities, or lack of
experience and knowledge, unless they have
been given supervision or instruction concerning
the use of the appliance by a person responsible
for their safety. Children should be supervised to
ensure that they do not play with the appliance.
4
IMPORTANT–
Read and Follow!
WARNING
DANGER
MOVING HAZARD
CHEMICAL HAZARD
To avoid risk of severe personal
injury; this appliance requires two
or more personnel while handling
and moving. Possible use of
appliance moving devices is
recommended.
To avoid risk of property damage
and/or personal injury or death;
this appliance is not too be used
as a heating source.
• Benzene is a chemical which is part of the
gas supply to this cooking product, which is
consumed in the flames during combustion.
Exposure to a small amount of benzene is
possible if a gas leak occurs. Formaldehyde
and soot are by-products of incomplete
combustion.
• This appliance contains or produces
chemicals which can cause serious injury or
death and which are known to the state of
California to cause cancer, birth defects or
other reproductive harm. To reduce the risk
from substances in the fuel or from fuel
combustion make sure this appliance is
installed, operated, and maintained in
accordance to the instructions in this
document.
WARNING
TIPPING HAZARD
•
•
•
DANGER
•
To reduce the risk of property
damage or personal injury; install
anti-tipping device provided in
accordance with the installation
instructions in this document.
Device must be engaged properly
to prevent product from tipping
over.
THIS RANGE CAN TIP
INJURIES TO PERSONS CAN RESULT
INSTALL ANTI-TIP DEVICE PACKED
WITH RANGE
SEE INSTALLATION INSTRUCTIONS
ELECTRICAL SHOCK
HAZARD
DANGER
To avoid risk of electrical shock,
personal injury or death; verify your
appliance has been properly grounded in
accordance with local codes or in absence of
codes, with the National Electrical Code
(NEC) ANSI/NFPA-70 – latest edition.
GAS LEAK HAZARD
To avoid risk of personal injury or
death; leak testing of the
appliance must be conducted
according to the manufacturer’s instructions.
Before placing appliance in operation, always
check for gas leaks with soapy water solution.
• DO NOT USE AN OPEN FLAME TO
CHECK FOR GAS LEAKS.
5
Dimensions
30” and 36” W. Models
35
(91-7/8
.1 ”
cm
)
29
-7/
8”
(75
.9
cm
)
1”
(2.
5c
m)
(9135-7
.1 /8”
cm
to min.
)
(94 37”
cm
ma
x.)
48” and 60” W. Models
6
(15 0”
2.4
c
m)
47
(12 7/8
1.6 ”
cm
)
1”
(2.
5c
m)
35
(91 -7/8
”
.1
cm
)m
to in.
(94
37
”
cm
)m
ax
Note: Unit shown with standard island trim.
6
.
Dimensions
Side View
28-1/16” (71.2 cm)
1-5/8”
(4.1 cm)
26-7/16” (67.2 cm)
1” (2.5 cm)
8-1/8”
(20.6 cm)
35-7/8”
(91.1 cm) min.
to
37”
(94.0 cm) max.
19-3/8”
25-3/4” (65.4 cm)
(49.2 cm)
45-1/8” (114.6 cm)
24-5/16” (61.8 cm)
Note: Unit shown with standard island trim.
7
Specifications
Overall width
Overall height
C/VGR530
C/VGR536
29-7/8” (75.9 cm)
35-7/8” (91.1.6 cm)
To top of side trim –35-7/8” (91.1 cm) min. 37” (94.0 cm) max.
Legs adjust – 1-1/8” (2.8 cm)
Overall depth from
rear*
To end of side panel - 24-5/16” (61.8 cm)
To front of door - 25-3/4” (65.4 cm)
To end of door handle - 28-11/16” (72.9 cm)
Additions to Base
Height
To top of island trim – add 1” (.5 cm)
To top of backguard – add 8” (0.3 cm)
To top of high shelf – add 23-1/2” (59.7 cm)
Gas requirements
Gas manifold pressure
Electrical
requirements
Maximum amp usage
Surface burner rating
Natural gas/LP
Griddle burner rating
Shipped Natural or LP/Propane, accepts standard residential 1/2” (1.3 cm) ID gas
service line. Unit is field convertible with proper conversion kit
Natural 5.0” W.C.P./ Liquid Propane L/P 10.0” W.C.P.
120VAC/60 Hz; 4 ft. (121.9 cm), 3-wire cord with grounded
3-prong plug attached to unit
1.0 amps
18,500 BTU (5.4 kW)/16,600 BTU 4.9 kW) power burner
15,000 BTU (4.4 kW)/12,500 BTU (3.7 kW)
N/A
Oven burner rating
Oven interior width
1.5 amps
15,000 BTU (4.4 kW) / 12,500 BTU (3.7 kW)
30,000 BTU (8.8 kW) Nat / LP
23” (58.4 cm)
29” (73.7 cm)
Oven interior height
16-1/8” (40.9 cm)
Oven interior depth
Overall
AHAM
18-3/4 (47.6 cm)
17” (43.2 cm)
Oven volume
Overall
AHAM
Approximate
shipping weight
4.0 cu. ft.
3.7 cu. ft
5.1 cu. ft.
5.1 cu. ft.
410 lbs. (184.5 kg)
500 lbs. (225 kg)
Minimum clearances from adjacent combustible construction:
Below cooking surface (36” [91.4 cm] and below)
• Sides - 0”
• Top grate support - 36” (91.4 cm)
Above cooking surface (above 36” [91.4 cm])
• Sides - 6” (15.2 cm)
• Within 6” (15.2 cm) side clearance, wall cabinets no deeper than 13” (33.0 cm) must be minimum 18” (45.7 cm)
above cooking surface
• Wall cabinets directly above product must be a minimum of 42” (106.7 cm) above cooking surface, unless a
range hood is installed above the cooking surface.
• Rear - 0” with 8” backguard or high shelf; 0” with island trim and non-combustible rear wall;
• 6” (15.2 cm) with island trim and combustible rear wall
Note: Clearances from non-combustible materials are not part of the ANSI Z21.1 scope and not certified by
CSA. Clearances to non-combustible materials must be approved by the authority having jurisdiction.
8
Specifications
C/VGR548
C/VGR560
Overall width
47-7/8” (121.6 cm)
60” (152.4 cm)
Overall height
To top of side trim –35-7/8” (91.1 cm) min. 37” (94.0 cm) max.
Legs adjust – 1-1/8” (2.8 cm)
Overall depth from
rear*
To end of side panel - 24-5/16” (61.8 cm)
To front of door - 25-3/4” (65.4 cm)
To end of door handle - 28-11/16” (72.9 cm)
Additions to Base
Height
To top of island trim – add 1” (.5 cm)
To top of backguard – add 8” (0.3 cm)
To top of high shelf – add 23-1/2” (59.7 cm)
Gas requirements
Gas manifold pressure
Electrical
requirements
Maximum amp usage
Shipped Natural or LP/Propane, accepts standard residential 1/2” (1.3 cm) ID gas
service line. Unit is field convertible with proper conversion kit
Natural 5.0” W.C.P./ Liquid Propane L/P 10.0” W.C.P.
120VAC/60 Hz; 4 ft. (121.9 cm), 3-wire cord with grounded
3-prong plug attached to unit
2.0 amps
2.0 amps
Surface burner rating
Natural gas/LP
18,500 BTU (5.4 kW)/16,600 BTU 4.9 kW) power burner
15,000 BTU (4.4 kW)/12,500 BTU (3.7 kW)
Griddle burner rating
15,000 BTU (4.4 kW)/12,500 BTU (3.7 kW)
Grill burner rating
Oven burner rating
Oven interior width
N/A
18,000 BTU (5.3 kW)/16,000 BTU (4.7 kW)
Right oven - 30,000 (8.8 kW) BTU Nat/LP Both ovens - 30,000 (8.8 kW) BTU Nat/LP
Left oven - 15,000 (4.4 kW) BTU Nat/LP
Right oven - 23” (58.4 cm)
Left oven - 12-1/8” (30.8 cm)
Oven interior height
Oven interior depth
Overall
AHAM
Oven volume
Overall
AHAM
Approximate
shipping weight
Both ovens - 23” (58.4 cm)
16-1/8” (40.9 cm)
18-3/4 (47.6 cm)
17” (43.2 cm)
Right 4.0 cu. ft. / Left 2.1 cu. ft.
Right 3.7 cu. ft. / Left 2.0 cu. ft.
Both Ovens 4.0 cu. ft.
Both Ovens 3.7 cu. ft.
575 lbs. (258.5 kg)
750 lbs. (337.5 kg)
Minimum clearances from adjacent combustible construction:
Below cooking surface (36” [91.4 cm] and below)
• Sides - 0”
• Top grate support - 36” (91.4 cm)
Above cooking surface (above 36” [91.4 cm])
• Sides - 6” (15.2 cm)
• Within 6” (15.2 cm) side clearance, wall cabinets no deeper than 13” (33.0 cm) must be minimum 18” (45.7 cm)
above cooking surface
• Wall cabinets directly above product must be a minimum of 42” (106.7 cm) above cooking surface, unless a
range hood is installed above the cooking surface.
• Rear - 0” with 8” backguard or high shelf; 0” with island trim and non-combustible rear wall;
• 6” (15.2 cm) with island trim and combustible rear wall
Note: Clearances from non-combustible materials are not part of the ANSI Z21.1 scope and not certified by
CSA. Clearances to non-combustible materials must be approved by the authority having jurisdiction.
9
Clearance Dimensions
(Proximity to Cabinets)
• This range may be installed directly adjacent
to existing 36” (91.4 cm) high base cabinets.
IMPORTANT: The side trim MUST be
3/8” (.95 cm) above the adjacent base
cabinet countertop. This can be
accomplished by raising the unit using
the adjustment spindles on the legs.
29
(75-7/8
.9 ”
cm
.
)
x
a
m m)
”
133.0 c
(3
• The range CANNOT be installed directly
adjacent to sidewalls, tall cabinets, tall
appliances, or other side vertical surfaces
above 36” (91.4 cm) high. There must be a
minimum of 6” (15.2 cm) side clearance from
the range to such combustible surfaces
above the 36” (91.4 cm) counter height.
4 6.7
6”
0
(15 min (1
.2 .
cm
)
• Within the 6” (15.2 cm) side clearance to
combustible vertical surfaces above 36” (91.4
cm), the maximum wall cabinet depth must
be 13” (33.0 cm) and wall cabinets within this
6” (15.2 cm) side clearance must be 18”
(45.7 cm) above the 36” (91.4 cm) high
countertop.
in.
” mcm)
8
1 7
”
36 cm)
”
3/8 m)
.4
(91
95
(0.
(45
.
c
A
• Wall cabinets above the range must be a
minimum of 42” (06.7 cm) above the range
cooking surface for the full width
of the range. This minimum height
requirement does not apply if a range hood
is installed over the cooking surface.
CAUTION
Range WIdth
“A” Dimension
30”
30” (76.2 cm)
36”
36” (9.4 cm)
48”
48” (121.9 cm)
60”
BURN HAZARD
To avoid risk of personal injury;
the use of cabinets for storage
above the appliance may result
in a potential burn hazard. Combustible
items may ignite, metallic items may
become hot and cause burns. If a cabinet
storage is to be provided the risk can be
reduced by installing a rangehood that
projects horizontally a minimum 5" (12.7 cm)
beyond the bottom of cabinets.
n.
mi m)
”
c
2
60-1/4”
(153.0 cm)
Note: Minimum clearance for back wall is 0”
with backguard or high-shelf.
Note: If a range hood is installed, wall cabinets above
the range have a different minimum clearance height.
Note: Clearances from non-combustible materials are
not part of the ANSI Z21.1 scope and not certified by
CSA. Clearances to non-combustible materials must be
approved by the authority having jurisdiction.
10
Clearance Dimensions
The bottom of a standard hood should be
30” (76.2 cm) min. to 36” (91.4 cm) max.
above the countertop. This would
typically result in the bottom of the hood
being 66” (167.6 cm) to 72” (182.9 cm)
above the floor. Refer to the range hood
installation instructions for additional
information. These dimensions provide for
safe and efficient operation of the hood.
(Wood/Composite Overlay)
Wo
o
d/C
o
Ov mpo
erl sit
ay e
”
24 cm)
.0
66
(61
(16 ”mi
7.6 n.
c
72 to m)
(18 ”ma
2.9 x.
cm
)
0” )
m
c
(0
30
(76”min
.2 .
cm
36 to )
”
m
(91 a
.4 x.
cm
)
Wo
o
d/C
o
Ov mpo
erl sit
ay e
66
(16 ”mi
7.6 n.
c
72 to m)
”
(18 ma
2.9 x.
cm
)
”
30 cm)
.2
(76
6” m)
.2 c
(15
30
Wall Installation
(76”min
.2 .
cm
36 to )
”
(91 ma
.4 x.
cm
)
Note: Minimum clearance for back
wall is 0” with backguard or highshelf.
Note: This range comes standard with an
Island Trim. There must be a minimum of
6” (15.2 cm) clearance from rear of range
to a combustible wall or 0” clearance to
a non-combustible wall.
Note: Clearances from non-combustible
materials are not part of the ANSI Z21.1
scope and not certified by CSA.
Clearances to non-combustible materials
must be approved by the authority
having jurisdiction.
Island Installation
11
Electrical & Gas Requirements
Electrical Requirements - Gas Ranges
Pressure Regulator:
Check your national and local codes regarding
this unit. This range requires 120VAC/60 Hz; 4 ft.
(121.9 cm), 3-wire cord with grounded 3-prong
plug attached to unit. See “Electrical
Connection” section for grounding instructions.
Must be fused seperately from any other circuit.
• All heavy-duty, commercial type cooking
equipment must have a pressure
regulator on the incoming service line
for safe and efficient operation, since
service pressure may fluctuate with local
demand. External regulators are not
required on this range since a regulator
is built into each unit at the factory.
Under no condition bypass this built-in
regulator.
Gas Connection
The gas supply (service) line must be the
same size or greater than the inlet line of the
appliance. This range uses a 1/2” (1.3 cm) ID
NPT (Sch40) inlet. Sealant on all pipe joints must
be resistive to LP gas.
The range is designed specifically for natural
gas or liquid propane (LP) gas. Before
beginning installation verify that the model is
compatible with the intended gas supply.
Manual shut-off valve:
This installer-supplied valve must be installed in
the gas service line before the appliance in the
gas stream and in a location where it can be
reached quickly in the event of an emergency.
Any opening behind the range shall be sealed.
In Massachusetts: A “T” handle type manual
valve must be installed in the gas supply line to
the appliance.
WARNING
ELECTRICAL SHOCK
HAZARD
To avoid the risk of electrical
shock, personal injury or death;
verify electrical power is turned off at the
breaker box and gas supply is turned off until
the range is installed and ready to operate,
installation by an authorized installer only.
12
• Manifold pressure should be checked
with a manometer, natural gas requires
5.0” W.C.P. and LP gas requires 10.0”
W.C.P. Incoming line pressure upstream
from the regulator must be 1” W.C.P.
higher than the manifold pressure in
order to check the regulator. The
regulator used on this range can
withstand a maximum input pressure of
1/2” PSI (14.0” W.C.P.). If the line
pressure is in excess of that amount, a
step down regulator will be required.
• The appliance must be disconnected
from the gas supply piping system
during any pressure testing of that
system.
Electrical & Gas Requirements
Flexible Connections:
If the unit is to be installed with flexible
couplings and/or quick-disconnect fittings, the
installer must use a heavy-duty AGA
design-certified flexible connector of at least
1/2” (1.3 cm) ID NPT (with suitable strain
reliefs) in compliance with ANSI Z21.41
and Z21.69.
In Canada: CAN 1-6, 10-88 metal connectors
for gas appliances and CAN
1-6.9 M79 quick disconnect devices for use
with gas fuel.
In Massachusetts: This appliance must be
installed with a 36” (3-foot) long flexible
gas connector.
Gas connection
in this area
31-1/16”
4”
(78.9 cm)
(10.2 cm)
1-1/16”
(2.7 cm)
3-3/4”
(9.5 cm)
13
Gas or electrical
connection in
this area
General Information
READ AND FOLLOW ALL WARNING AND CAUTION INFORMATION WHEN
INSTALLING THIS APPLIANCE.
• All openings in the wall behind the appliance and in the floor under the appliance must be
sealed.
• DO NOT obstruct the flow of combustion and ventilation air.
NOTICE
CAUTION
DO NOT use the handle or oven door
to lift the oven. Remove door before
installation to ensure that it is not used
to lift the unit. DO NOT lift or carry the
door by the handle.
Avoid any damage to oven vents. The
vents need to be unobstructed and open to
provide proper airflow for optimal oven
performance.
CAUTION
Removing the door must be done by
your dealer, a qualified licensed plumber,
or certified gas installer.
The cooling fan should be operating when
the unit is in operation. If you notice the
cooling fan is not operating or you observe
unusual or excessive noise coming from
the cooling fan, contact an Authorized
Service Center before continuing operation.
Failure to do so can result in damage to
the oven or surrounding cabinets.
DO NOT DISCARD ORIGINAL PACKING
MATERIALS UNTIL UNIT HAS BEEN
INSTALLED AND IS WORKING PROPERLY.
IF UNIT IS RETURNED FOR ANY REASON,
IT MUST BE PACKED IN ORIGINAL
PACKAGING
Moving, Handling, and Unpacking
Remove and discard all packing materials,
including cardboard and tape on the outside
and inside of the range.
Remove the burner grates, burner heads, and
bases from the cardboard top packaging.
DO NOT discard the metal brackets supplied
with the range. These are the anti-tip devices
and must be installed with the unit. Refer to
“Anti-tip Device Installation” section.
Some stainless steel parts may have a plastic
protective wrap which must be peeled off.
The interior should be washed thoroughly
with hot, soapy water to remove film residues
and any dust or debris before being used,
then rinsed and wiped dry. Solutions stronger
than soap and water are rarely needed.
14
Door Removal
1
step
2
Open door completely.
Fold latches backward until locked in place.
4
3
Lift door up and out.
Slowly close until latches stop door.
15
1
2
step
step
Leg Installation
1
1
3
2
Note: It is strongly recommended
that a pallet or lift jack be used rather than tilting. Raise
unit about a foot. Unscrew shipping bolts from couplings on
all four corners.
3
4
step
step
Legs are packed in cardboard top pack. Note: Legs
should be installed near to where appliance is to be
used, as they are not secure for long transit.
Screw legs into couplings on all four corners. The 48” W.
ranges have two additional legs located in the center of
the unit.
Lower range gently to keep any undue strain from
legs and internal mounting hardware.
Leveling/Adjustments/Alignment
2
1
Measure the four corners in cutout area to verify
if flooring is level.
16
For uneven or sloped floors, level unit with metal
shims only, as the adjustment required may exceed
the thread available in the legs.
3
4
step
step
Installation
5c
0.9
m
Check that unit is level side to
side and front to back. Side trim of the lowest
corner must be 3/8” (0.95 cm) above countertop.
5
6
step
step
Move unit into opening.
1
1
2
If leveling is required, move unit out of opening.
Lift unit and prop on wood blocks.
step
7
Set the high corner of range so that the top of side trim is
3/8” (0.95 cm) above countertop. Level range to high
corner.
17
Installation
Anti-tip Device Installation (Wall Mount)
1
step
WARNING
TIPPING HAZARD
To reduce the risk of property
damage or personal injury;
install anti-tipping device
provided in accordance with
the installation instructions
in this document. Device
must be engaged properly to
prevent product from tipping
over.
Me
as
ur
em
en
t
(A
)
Measure from floor to bottom
of the anit-tip opening located on the back of
range. This will be measurement (A).
Y
step
2
30”
X
A)
t(
n
me cm)
ure(1.3
s
a ”
Me 1/2
+
Dimension
“X”
21-1/2”
(54.6 cm)
Dimension
“Y”
N/A
36”
24-1/2”
(62.2 cm)
N/A
48”
21-1/2”
(54.6 cm)
N/A
21-3/4”
(55.2 cm)
5-1/2”
(14.0 cm)
60”
3
4
step
step
Locate anti-tip bracket on rear wall with the top left corner at
measurement (A) plus 1/2” (1.3 cm) from the floor and “X” dimension
(see chart) from where the right side of range (facing range) is to be
located and “Y” dimension (60” ranges only-see chart) from where the
left side of the range (facing range) is to be located.
Mark and drill holes where bracket will be located.
Attach bracket with
mounting hardware provided.
18
Installation
Anti-tip Device Installation (Floor Mount)
1
A
B
*(Add only when
using 8” backguard)
1-1
/4”
+
12-3/4”
(32.4 cm)
16”
(40.6 cm)
3/8”
(.95 cm)
1/2”
(1.3 cm)
48”
16”
(40.6 cm)
1/2”
(1.3 cm)
60”
16”
(40.6 cm)
1”
(2.5 cm)
30”
B*
36”
A
Ø
1
(.3 /8”
2c
m)
Locate anti-tip bracket hook on the floor Dim A from side cabinet
and 1-1/4” (3.2 cm) from rear wall when using an island trim or high
shelf. If using an 8” (20.3 cm) backguard, add Dim B to the 1-1/4”.
Mark and drill 1/8” (.32 cm) holes where bracket will be located.
2
3
1
1
2
x2
Mount anti-tip bracket hook to floor using screws
provided.
1
2
Remove two screws from back of range.
4
1
1
2
Attach bracket to back of range using two screws.
19
Installation
Connecting Gas & Electric
1
step
DANGER
GAS LEAK HAZARD
To avoid risk of personal injury or
death; leak testing of the
appliance must be conducted
according to the manufacturer’s instructions.
Before placing appliance in operation, always
check for gas leaks with soapy water solution.
• DO NOT USE AN OPEN FLAME TO
CHECK FOR GAS LEAKS.
Connect gas and electrical. Before placing appliance in
operation, always check for gas leaks. This must be
performed by your dealer, a qualified licensed plumber, or
gas service company.
Standoff Spacer Removal
DANGER
FIRE HAZARD
Backguards come standard with
standoff spacers which provide
a barrier between back of range and rear
wall. These must be in place for adequate
ventilation. Standoff spacers can only be
removed if range is installed against a
Non-Combustible wall.
1
2
step
step
Final Installation
Slide range into place. Be sure
wall anit-tip bracket slides into the anit-tip
opening and floor anti-tip hook and bracket are
engaged.
Make sure rear trim is properly installed.
20
3
4
step
step
Installation
m
ccm
55
9
9
.
.
00
Check that unit is level side to side
and front to back. The side trim must be 3/8” (0.95
cm) above countertop. If unit is not level repeat
Steps 5-7 of “Leveling/Adjustments/Alignment”
section.
Burner heads and bases are packed in cardboard top
pack with the grates. Place burner bases on top of the
burner flanges and burner heads on top of the burner
base. Place burner grate on top of grate support.
1
2
step
step
Door Replacement
2
Open door completely.
Fold latches forward until locked in place.
Carefully realign door on hinges. Slide in and
down.
step
3
Close door.
21
Final Preparation
• All stainless steel body parts should be wiped with hot, soapy water and with a liquid cleaner
designed for this material. If buildup occurs, DO NOT use steel wool, abrasive cloths,
cleansers, or powders! If it is necessary to scrape stainless steel to remove encrusted
materials, soak with hot, wet cloths to loosen the material, then use a wooden or nylon
scraper. DO NOT use a metal knife, spatula, or any other material tool to scrape stainless steel!
Scratches are almost impossible to remove.
Performance Checklist
A qualified installer should carry out the following checks:
1-1/2”
□ Check top burner ignition. See drawing for proper flame
height on HI. The low flame should light at every port.
(3.8 cm)
□ Check oven bake function—bake burner on full power.
□ Check convection bake function—bake burner at full power with the
convection fan on.
□ Check broil function—broil burner at full power.
□ Check convection broil function—broil burner at full power with
convection fan on.
□ Check convection fan function—convection fan comes on when
switch is turned on.
22
3/8”
(0.95 cm)
Service & Registration
Only authorized replacement parts may be used in performing service on the appliance.
All servicing should be referred to a qualified technician.
Contact Viking Range, LLC, 1-888-(845-4641), for the nearest service parts distributor in your
area or write to:
VIKING RANGE, LLC
PREFERRED SERVICE
111 Front Street
Greenwood, Mississippi 38930 USA
The serial number and model number for your appliance can be found
by opening the door and looking under the control panel. A duplicate
label is located on the back side of the range.
Record the following information indicated below. You will need it if
service is ever required.
Model number ____________________________________________________________________________________
Serial number _____________________________________________________________________________________
Date of purchase __________________________________________________________________________________
Date installed ______________________________________________________________________________________
Dealer's name _____________________________________________________________________________________
Address ___________________________________________________________________________________________
These installation instructions should remain with the unit
for future reference.
23
Viking Range, LLC
111 Front Street
Greenwood, Mississippi 38930 USA
(662) 455-1200
For product information, call 1-888-(845-4641)
or visit vikingrange.com in the US
or brigade.ca in Canada
055065-000A EN
(031517)
Download PDF

advertising