Viking | VDR7488BSSLP | Use and Care Manual | Viking VDR7488BSSLP Use and Care Manual

Installation Guide
®
Viking Range, LLC
111 Front Street
Greenwood, Mississippi 38930 USA
(662) 455-1200
For product information, call 1-888-(845-4641)
or visit vikingrange.com
7 Series
Professional Freestanding Ranges
F21234C EN
(060114)
Table of Contents
IMPORTANT–
Warnings & Important Safety Instructions _______________________________________________3
• Before beginning, please read these
instructions completely and carefully.
Your safety and the safety of others is
very important.
• DO NOT remove permanently affixed
labels, warnings, or plates from product.
This may void the warranty.
We have provided many important safety
messages in this manual and on your
appliance. ALWAYS read and obey all
safety messages.
Dimensions _________________________________________________________________________6
Specifications _______________________________________________________________________8
Clearance Dimensions (Proximity to Cabinets)__________________________________________10
Clearance Dimensions (Wood/Composite Overlay) _____________________________________11
Read and Follow!
Electrical & Gas Requirements _______________________________________________________12
General Information ________________________________________________________________14
Installation _________________________________________________________________________15
Door Removal __________________________________________________________________15
Leg Installation _________________________________________________________________16
Electrical Connection (3-wire) _____________________________________________________17
Electrical Connectin (4-wire) ______________________________________________________19
Leveling/Adjustments/Alignment _________________________________________________19
Anti-tip Device Installation _______________________________________________________22
This is the safety alert symbol. This
symbol alerts you to hazards that
can kill or hurt you and others.
• All local and national codes and ordinances
must be observed. Installation must
conform with local codes or in the absence
of codes, the National Fuel Gas Code ANSI
Z223.1 INFPA54.
All safety messages will be preceded by
the safety alert symbol and the word
“DANGER,” “WARNING” or “CAUTION.”
These words mean:
• The installer must leave these instructions
with the consumer who should retain for
local inspector’s use and for future
reference.
DANGER
Hazards or unsafe practices
which WILL result in severe personal
injury or death.
Connecting Gas & Electric _______________________________________________________24
Standoff Spacer Removal ________________________________________________________24
Final Installation ________________________________________________________________24
Door Replacement ______________________________________________________________25
Final Preparation ___________________________________________________________________26
Performance Checklist ______________________________________________________________26
Service & Registration_______________________________________________________________27
In Canada: Installation must be in accordance
with the current CAN/CGA B149.1 & 2 Gas
Installation codes and/or local codes. Electrical
installation must be in accordance with the
current CSA C22.1 Canadian Electrical Codes
Part 1 and/or local codes.
WARNING
Hazards or unsafe practices
which COULD result in severe personal
injury or death.
CAUTION
In Massachusetts: All gas products must be
installed by a “Massachusetts” licensed
plumber or gasfitter. A “T” type handle
manual valve must be installed in the gas
supply line to the appliance.
Hazards or unsafe practices which
COULD result in minor personal injury or
property damage.
All safety messages will identify the
hazard, tell you how to reduce the chance
of injury, and tell you what can happen if
the instructions are not followed.
An air curtain or other overhead range hood
which operates by blowing a downward
airflow onto the range, shall not be used with
a gas range
2
3
IMPORTANT–
Read and Follow!
A GFI shall be used if required by NFPA-70 (National Electric Code), federal/state/local
laws, or local ordinances.
• The required use of a GFI is normally related to the location of a receptacle with respect to
any significant sources of water or moisture.
• Viking Range, LLC will NOT warranty any problems resulting from GFI outlets which are not
installed properly or do not meet the requirements below.
If
•
•
•
•
the use of a GFI is required, it should be:
Of the receptacle type (breaker type or portable type NOT recommended)
Used with permanent wiring only (temporary or portable wiring NOT recommended)
On a dedicated circuit (no other receptacles, switches or loads in the circuit)
Connected to a standard breaker of appropriate size (GFI breaker of the same size NOT
recommended)
• Rated for Class A (5 mA +/- 1 mA trip current) as per UL 943 standard
• In good condition and free from any loose-fitting gaskets (if applicable in outdoor situations)
• Protected from moisture (water, steam, high humidity) as much as reasonably possible
DANGER
WARNING
To prevent possible damage to cabinets
and cabinet finishes, use only materials
and finishes that will not discolor or
delaminate and will withstand temperatures
up to 194°F (90°C). Heat resistant
adhesive must be used if the product is to
be installed in laminated cabinetry. Check
with your builder or cabinet supplier to
make sure that the materials meet these
requirements.
FIRE/EXPLOSION
HAZARD
IF THE INFORMATION IN
THIS MANUAL IS NOT
FOLLOWED EXACTLY, A FIRE OR
EXPLOSION MAY RESULT CAUSING
PROPERTY DAMAGE, PERSONAL
INJURY, OR DEATH.
• DO NOT store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
• WHAT TO DO IF YOU SMELL GAS:
–DO NOT try to light any appliance.
–DO NOT touch any electrical switch;
DO NOT use any phone in your
building.
–Immediately call your gas supplier from
a neighbor’s phone.
–Follow the gas supplier’s instructions.
–If you cannot reach your gas supplier,
call the fire department.
• Installation and service must be
performed by a qualified installer, service
agency, or the gas supplier.
4
IMPORTANT–
Read and Follow!
WARNING
DANGER
MOVING HAZARD
CHEMICAL HAZARD
To avoid risk of severe
personal injury; this appliance
requires two or more personnel
while handling and moving. Possible
use of appliance moving devices is
recommended.
To avoid risk of property
damage and/or personal injury
or death; this appliance is not
too be used as a heating source.
• Benzene is a chemical which is part of
the gas supply to this cooking product,
which is consumed in the flames during
combustion. Exposure to a small
amount of benzene is possible if a gas
leak occurs. Formaldehyde and soot are
by-products of incomplete combustion.
• This appliance contains or produces
chemicals which can cause serious
injury or death and which are known to
the state of California to cause cancer,
birth defects or other reproductive harm.
To reduce the risk from substances in
the fuel or from fuel combustion make
sure this appliance is installed,
operated, and maintained in accordance
to the instructions in this document.
WARNING
TIPPING HAZARD
•
•
•
DANGER
•
ELECTRICAL SHOCK
HAZARD
To avoid risk of electrical shock,
personal injury or death; verify
your appliance has been properly
grounded in accordance with local codes
or in absence of codes, with the National
Electrical Code (NEC) ANSI/NFPA-70 –
latest edition.
To reduce the risk of property
damage or personal injury;
install anti-tipping device
provided in accordance with
the installation instructions in
this document. Device must be
engaged properly to prevent
product from tipping over.
THIS RANGE CAN TIP
INJURIES TO PERSONS CAN
RESULT
INSTALL ANTI-TIP DEVICE PACKED
WITH RANGE
SEE INSTALLATION INSTRUCTIONS
DANGER
GAS LEAK HAZARD
To avoid risk of personal injury
or death; leak testing of the
appliance must be conducted
according to the manufacturer’s
instructions. Before placing appliance in
operation, always check for gas leaks
with soapy water solution.
• DO NOT USE AN OPEN FLAME TO
CHECK FOR GAS LEAKS.
5
Dimensions
Dimensions
36” and 48” W. Ranges
36” and 48” W. Ranges
30” (76.2 cm)
27-3/4 (70.5 cm)
47
(1 -7/
21
35
8
.6 ”
cm
)
2-1/4”
(5.7 cm)
1”
(2.5 cm)
(91-7/8
.1 ”
cm
)
8”
(20.3 cm)
35-15/16”
(91.3 cm) min.
to
37-9/16”
(95.4 cm) max.
3
5
(91 -15
.3 /16
cm ”
)m
3 to in.
(95 7-9
.4 /16
cm ”
)m
ax
.
25-1/4”
(64.1 cm)
19-3/8”
26-15/16”
(49.2 cm)
(68.4 cm)
46-5/16”
(117.6 cm)
Note: Unit shown with standard island trim.
Note: All ranges installed with a backguard against a combustible wall require a standoff with
the backguard which will add 3/4” (1.9 cm) to the overall range depth.
6
Note: Unit shown with standard island trim.
7
Specifications
Specifications
Dual Fuel 36” and 48” W. Ranges
Gas 36” and 48” W. Ranges
Description
36” W. Models
48” W. Models
Description
36” W. Models
48” W. Models
Overall width
35-7/8” (91.1 cm)
47-7/8” (121.6 cm)
Overall width
35-7/8” (91.1 cm)
47-7/8” (121.6 cm)
Overall height
To top of side trim – 35-15/16” (91.3 cm) min. 37-9/16” (95.4 cm) max.
Legs adjust – 1-5/8” (4.1 cm)
Overall height
To top of side trim – 35-15/16” (91.3 cm) min. 37-9/16” (95.4 cm) max.
Legs adjust – 1-5/8” (4.1 cm)
Overall depth from
rear*
To end of side panel – 25-1/4” (64.1 cm)
To front of door – 26-15/16” (68.4 cm)
To end of door handle – 30” (76.2 cm)
*Add 3/4” (1.9 cm) to overall depth for models installed against a combustible wall.
Overall depth from
rear*
To end of side panel – 25-1/4” (64.1 cm)
To front of door – 26-15/16” (68.4 cm)
To end of door handle – 30” (76.2 cm)
*Add 3/4” (1.9 cm) to overall depth for models installed against a combustible wall.
Additions to Overall
Height
To top of island trim – add 1” (2.5 cm)
To top of backguard – add 10” (25.4 cm)
To top of high shelf – add 24-1/8” (61.3 cm)
Additions to Overall
Height
To top of island trim – add 1” (2.5 cm)
To top of backguard – add 10” (25.4 cm)
To top of high shelf – add 24-1/8” (61.3 cm)
Gas requirements
Gas manifold pressure
Electrical
requirements
Shipped Natural or LP/Propane, accepts
standard residential 1/2” (1.3 cm) ID gas
service line. Unit is field convertible with
proper conversion kit
Shipped Natural or LP/Propane, accepts
standard residential 3/4” (1.9 cm) ID gas
service line. Unit is field convertible with
proper conversion kit
Natural 5.0” W.C.P./ Liquid Propane L/P 10.0” W.C.P.
Gas requirements
Gas manifold pressure
Shipped Natural or LP/Propane, accepts standard residential 1/2” (1.3 cm) ID gas service
line. Unit is field convertible with proper conversion kit.
Natural 5.0” W.C.P./ Liquid Propane L/P 10.0” W.C.P.
120VAC/60 Hz; 4 ft. (121.9 cm), 3-wire cord with grounded
3-prong plug attached to unit
Electrical
requirements
Maximum amp usage
1.5 amps
Maximum amp usage
240V - 28.5 amps / 208V - 24.7 amps
Surface burner rating
Natural gas/LP
Front: (3) 23,000 BTU (6.7 kW) / 20,000 BTU (5.8 kW)
Rear: (2) 15,000 BTU (4.4 kW) / 13,500 BTU (4.0 kW)
(1) 8,000 BTU (2.3 kW) / 8,000 BTU (2.3 kW)
Surface burner rating
Natural gas/LP
Front: (3) 23,000 BTU (6.7 kW) / 20,000 BTU (5.9 kW)
Rear: (2) 15,000 BTU (4.4 kW) / 13,500 BTU (4.0 kW)
(1) 8,000 BTU (2.3 kW) / 8,000 BTU (2.3 kW)
Griddle burner rating
Nat gas/LP (if applicable)
Oven interior width
2.0 amps
15,000 BTU (4.4 kW) / 13,500 BTU (4.0 kW)
29” (73.7 cm)
Oven interior height
Approximate
shipping weight
Right oven - 23” (58.4 cm)
Left oven - 12-1/8” (30.8 cm)
16-1/8” (40.9 cm)
Oven interior depth
Overall
AHAM
Oven volume
Overall
AHAM
Front: (4) 23,000 BTU (6.7 kW) / 20,000 BTU (5.8 kW)
Rear: (3) 15,000 BTU (4.4 kW) / 13,500 BTU (4.0 kW)
(1) 8,000 BTU (2.3 kW) / 8,000 BTU (2.3 kW)
18-3/4” (47.6 cm)
17” (43.2 cm)
5.1 cu. ft.
4.6 cu. ft.
Right - 4.0 cu. ft. / Left - 2.1 cu. ft.
Right - 3.7 cu. ft. / Left - 2.0 cu. ft.
525 lbs. (236.6 kg)
641 lbs. (288.5 kg)
See Electrical Requirements information
Griddle burner rating
Nat gas/LP (if applicable)
Oven interior width
240V - 43.0 amps / 208V - 37.3 amps
Front: (4) 23,000 BTU (6.7 kW) / 20,000 BTU (5.9 kW)
Rear: (3) 15,000 BTU (4.4 kW) / 13,500 BTU (4.0 kW)
(1) 8,000 BTU (2.3 kW) / 8,000 BTU (2.3 kW)
15,000 BTU (4.4 kW) / 13,500 BTU (4.0 kW)
30-5/16” (77.0 cm)
Right oven - 25-5/16” (64.3 cm)
Left oven - 13-3/4” (34.9 cm)
Oven interior height
16-1/2” (41.9 cm)
Oven interior depth
Overall
AHAM
19-1/2” (49.5 cm)
16-13/16” (42.7 cm)
Oven volume
Overall
AHAM
Approximate
shipping weight
5.6 cu. ft.
4.9 cu. ft.
Right - 4.7 cu. ft. / Left - 2.6 cu. ft.
Right - 4.1 cu. ft. / Left - 2.2 cu. ft.
525 lbs. (236.6 kg)
641 lbs. (288.5 kg)
Minimum clearances from adjacent combustible construction:
Below cooking surface (36” [91.4 cm] and below)
• Sides - 0”
• Top grate support - 36” (91.4 cm)
Above cooking surface (above 36” [91.4 cm])
Minimum clearances from adjacent combustible construction:
Below cooking surface (36” [91.4 cm] and below)
• Sides - 0”
• Top grate support - 36” (91.4 cm)
Above cooking surface (above 36” [91.4 cm])
• Sides - 12” (30.5 cm)
• Within 12” (30.5 cm) side clearance, wall cabinets no deeper than 13” (33.0 cm) must be minimum 18” (45.7 cm)
above cooking surface
• Wall cabinets directly above product must be a minimum of 58” (147.3 cm) above cooking surface, unless a range hood is
installed above the cooking surface.
• Rear - 3/4” (1.9 cm) with 10” backguard or high shelf; 0” with island trim and non-combustible rear wall
• 6” (15.2 cm) with island trim and combustible rear wall
Note: Clearances from non-combustible materials are not part of the ANSI Z21.1 scope and not certified by
CSA. Clearances to non-combustible materials must be approved by the authority having jurisdiction.
8
• Sides - 12” (30.5 cm)
• Within 12” (30.5 cm) side clearance, wall cabinets no deeper than 13” (33.0 cm) must be minimum 18” (45.7 cm)
above cooking surface
• Wall cabinets directly above product must be a minimum of 58” (147.3 cm) above cooking surface, unless a range hood
is installed above the cooking surface.
• Rear - 3/4” (.9 cm) with 10” backguard or high shelf; 0” with island trim and non-combustible rear wall;
• 6” (15.2 cm) with island trim and combustible rear wall
Note: Clearances from non-combustible materials are not part of the ANSI Z21.1 scope and not certified by
CSA. Clearances to non-combustible materials must be approved by the authority having jurisdiction.
9
Clearance Dimensions
Clearance Dimensions
(Proximity to Cabinets)
• Wall cabinets above the range must be a
minimum of 58” (147.3 cm) above the
range cooking surface for the full width
of the range. This minimum height
requirement does not apply if a range
hood is installed over the cooking surface.
• This range may be installed directly
adjacent to existing 36” (91.4 cm) high
base cabinets.
IMPORTANT: The side panel MUST be
3/8” (.95 cm) above the adjacent base
cabinet countertop. This can be
accomplished by raising the unit using
the adjustment spindles on the legs.
• The range CANNOT be installed
directly adjacent to sidewalls, tall
cabinets, tall appliances, or other
side vertical surfaces above
36” (91.4 cm) high. There must be
a minimum of 12” (30.5 cm) side
clearance from the range to such
combustible surfaces above the
36” (91.4 cm) counter height.
The bottom of a standard hood should be
30” (76.2 cm) min. to 36” (91.4 cm) max.
above the countertop. This would
typically result in the bottom of the hood
being 66” (167.6 cm) to 72” (182.9 cm)
above the floor. Refer to the range hood
installation instructions for additional
information. These dimensions provide for
safe and efficient operation of the hood.
Wo
od
/Co
Ov mpo
erl sit
ay e
”
24 cm)
.0
(61 or
66
(16 ”mi
7.6 n.
cm
72 to )
(18 ”ma
2.9 x.
cm
)
”
27 cm)
”
0 )
cm
(0
”m )
13 .0 cm
(33
in.
”m )
587.3 cm
(30 min
.5 .
cm
)
in.
”m )
18 .7 cm
”
36 cm)
(45
.4
(91
”
3/8cm)
9
(0.
5
66
(16 ”mi
7.6 n.
cm
72 to )
”
m
(18 a
2.9 x.
cm
)
”
30 cm)
.2
(76
6” m)
.2 c
5
(1
30
Wall Installation
(76”min
.2 .
cm
36 to )
”
(91 ma
.4 x.
cm
)
Note: Minimum clearance for back wall
is 3/4” (1.9 cm) with backguard or highshelf.
A
Range
Width
36”
48”
CAUTION
BURN HAZARD
“A”
Dimension
36” (91.4 cm)
48” (121.9 cm)
Note: Minimum clearance for back wall is 3/4”
(1.9 cm) with backguard or high-shelf.
Note: This range comes standard with an Island
Trim. There must be a minimum of 6” (15.2 cm)
clearance from rear of range to a combustible
wall or 0” clearance to a non-combustible wall.
Note: If a range hood is installed, wall cabinets above
the range have a different minimum clearance height.
Note: Clearances from non-combustible materials are
not part of the ANSI Z21.1 scope and not certified by
CSA. Clearances to non-combustible materials must be
approved by the authority having jurisdiction.
10
(76”min
.2 .
cm
36 to )
”
(91 ma
.4 x.
cm
)
Wo
od
/Co
Ov mpo
erl sit
ay e
(14
12
”
30
.6
(38
.
ax
• Within the 12” (30.5 cm) side
clearance to combustible vertical
surfaces above 36” (91.4 cm), the
maximum wall cabinet depth
must be 13” (33.0 cm) and wall
cabinets within this 12” (30.5 cm)
side clearance must be
18” (45.7 cm) above the
36” (91.4 cm) high countertop.
To avoid risk of personal injury;
the use of cabinets for storage
above the appliance may result
in a potential burn hazard. Combustible
items may ignite, metallic items may
become hot and cause burns. If a cabinet
storage is to be provided the risk can be
reduced by installing a rangehood that
projects horizontally a minimum
5" (12.7 cm) beyond the bottom of cabinets.
(Wood/Composite Overlay)
Note: Clearances from non-combustible
materials are not part of the ANSI Z21.1 scope
and not certified by CSA. Clearances to noncombustible materials must be approved by the
authority having jurisdiction.
Island Installation
11
Electrical & Gas Requirements
Electrical Requirements - Gas Ranges
Gas Connection
Check your national and local codes regarding
this unit. This range requires 120VAC/60 Hz; 4 ft.
(121.9 cm), 3-wire cord with grounded 3-prong
plug attached to unit. See “Electrical
Connection” section for grounding instructions.
Must be fused seperately from any other circuit.
This range has a 3/4" (1.9 cm) ID NPT
Sch40) inlet connection. For optimal
performance of the VGR748 Ranges, the
connector from the gas supply (service) line
should also be 3/4" ID. For all other
models, the gas supply (service) line may be
reduced, but not to less than ½” (1.3 cm) ID
NPT. We recommend the use of our 3/4"
GAS CONNECTOR KIT, part no. GCKVGR.
Sealant on all pipe joints must be resistive to
LP gas
Electrical Requirements - Dual Fuel
Ranges
This product is manufactured with the neutral
terminal connected to the cabinet. Use a 3-wire,
agency approved, power supply kit with closed
loop terminals rated per the National Electrical
Code, ANSI/NFPA 70-latest edition (See Rating
chart below). If local codes prohibit grounding
through the neutral, use a 4-wire, agency
approved, power supply kit with closed loop
terminals rated per the National Electrical Code,
ANSI/NFPA 70-latest edition (See Rating chart
below).
RATING*
Specified Rating of Power Supply
Cord Kit and Circuit Protection
120/240 Volts
12.5 - 16.5 KW
16.5 - 17.5 KW
120/208 Volts
9.2 - 12.5 KW
12.5 - 13.5 KW
Amps
40 or 50
50
*The National Electric Code calculation for
Electrical Load is less than the Total Connected
Electrical Load listed on the model/serial rating
plate.
WARNING
ELECTRICAL SHOCK
HAZARD
To avoid the risk of electrical
shock, personal injury or death;
verify electrical power is turned off at the
breaker box and gas supply is turned off
until the range is installed and ready to
operate, installation by an authorized
installer only.
12
The range is designed specifically for
natural gas or liquid propane (LP) gas.
Before beginning installation verify that
the model is compatible with the
intended gas supply.
Electrical & Gas Requirements
Flexible Connections:
• Manifold pressure should be checked with
a manometer, natural gas requires 5.0”
W.C.P. and LP gas requires 10.0” W.C.P.
Incoming line pressure upstream from the
regulator must be 1” W.C.P. higher than
the manifold pressure in order to check
the regulator. The regulator used on this
range can withstand a maximum input
pressure of 1/2” PSI (14.0” W.C.P.). If the
line pressure is in excess of that amount, a
step down regulator will be required.
If the unit is to be installed with flexible
couplings and/or quick-disconnect fittings,
the installer must use a heavy-duty AGA
design-certified flexible connector of at least
1/2” (1.3 cm) ID NPT (with suitable strain
reliefs) in compliance with ANSI Z21.41
and Z21.69. For the VGR 48” gas range the
installer must use a flexible connector of at
least 3/4” (.9 cm) ID NPT.
In Canada: CAN 1-6, 10-88 metal
• The appliance must be disconnected from
the gas supply piping system during any
pressure testing of that system.
connectors for gas appliances and CAN
1-6.9 M79 quick disconnect devices for use
with gas fuel.
In Massachusetts: This appliance must be
installed with a 36” (3-foot) long flexible
gas connector.
Manual shut-off valve:
This installer-supplied valve must be installed
in the gas service line before the appliance
in the gas stream and in a location where it
can be reached quickly in the event of an
emergency. Any opening behind the range
shall be sealed.
In Massachusetts: A “T” handle type
manual valve must be installed in the gas
supply line to the appliance.
Gas connection
in this area
23-7/16”
4”
Pressure Regulator:
• All heavy-duty, commercial type cooking
equipment must have a pressure regulator
on the incoming service line for safe and
efficient operation, since service pressure
may fluctuate with local demand. External
regulators are not required on this range
since a regulator is built into each unit at
the factory. Under no condition bypass
this built-in regulator.
(59.5 cm)
(10.2 cm)
1-1/16”
16”
(40.6 cm)
(2.7 cm)
Gas or electrical
connection in
this area
3-3/4”
(9.5 cm)
13
General Information
Installation
NOTICE
READ AND FOLLOW ALL WARNING
AND CAUTION INFORMATION
WHEN INSTALLING THIS APPLIANCE.
Moving, Handling, and Unpacking
Remove and discard all packing materials,
including cardboard and tape on the outside
and inside of the range.
• All openings in the wall behind the
appliance and in the floor under the
appliance must be sealed.
Remove the burner grates, burner heads, and
bases from the cardboard top packaging.
DO NOT discard the
metal brackets
supplied with the
range. These are the
anti-tip devices and
must be installed with
the unit. Refer to “Antitip Device Installation”
section.
• DO NOT obstruct the flow of combustion
and ventilation air.
CAUTION
Avoid any damage to oven vents. The
vents need to be unobstructed and open to
provide proper airflow for optimal oven
performance.
DO NOT use the handle or oven door
to lift the oven. Remove door before
installation to ensure that it is not used
to lift the unit. DO NOT lift or carry the
door by the handle.
Removing the door must be done by
your dealer, a qualified licensed plumber,
or certified gas installer.
Door Removal
2
1
CAUTION
The cooling fan should be operating when
the unit is in operation. If you notice the
cooling fan is not operating or you observe
unusual or excessive noise coming from
the cooling fan, contact a Viking Authorized
Service Center before continuing operation.
Failure to do so can result in damage to
the oven or surrounding cabinets.
Some stainless steel parts may have a plastic
protective wrap which must be peeled off.
The interior should be washed thoroughly
with hot, soapy water to remove film
residues and any dust or debris before being
used, then rinsed and wiped dry. Solutions
stronger than soap and water are rarely
needed.
Open door completely.
Fold latches backward until locked in place
3
4
Slowly close until latches stop door.
14
Lift door up and out.
15
Installation
Installation
Leg Installation
Electrical Connection (3-wire) - Dual Fuel Ranges
Note: If you have a 4-wire connection, see following section for
4-wire connection instructions.
2
1
WARNING
WARNING
Electrical shock hazard.
Electrical shock hazard.
1
1
3
2
Note: It is strongly recommended
that a pallet or lift jack be used rather than tilting.
Raise unit about a foot. Unscrew shipping bolts from
couplings on all four corners.
Legs are packed in cardboard top pack.
Note: Legs should be installed near to where
appliance is to be used, as they are
not secure for long transit.
4
3
To avoid risk of electrical shock,
personal injury or death; verify
your appliance has been
properly grounded in accordance with
local codes or in absence of codes, with
the National Electrical Code (NEC).
ANSI/NFPA 70-latest edition.
To avoid risk or electrical
shock, personal injury or death;
grounding product to the frame
of the unit may or may not be permitted
through your local codes. If ground to the
frame is not permitted then a 4 conductor
power cord must be used.
See Electrical Requirements information.
1
Where local codes do not permit grounding
through neutral, use a 4-wire power supply
cord. The cord or conduit must be secured
to the range with the strain relief bracket.
The electrical connection is made at the
terminal block, which is located behind the
access door on the back of the range.
Remove access door.
Lower range gently to keep any undue strain from
legs and internal mounting hardware.
Screw legs into couplings on all four corners.
The 48” W. ranges have two additional legs located in the
center of the unit.
3
2
Remove supply cord strain relief
bracket and three supply cord mounting screws
on terminal block.
16
Feed supply cord up through hole in bottom
of range back.
17
Installation
Installation
Electrical Connection (3-wire) Dual Fuel Ranges (cont.)
Electrical Connection (4-wire) Dual Fuel Ranges
5
4
1
Push supply cord toward terminal
block to relieve strain, reattach supply cord strain relief
bracket over supply cord.
Attach line #1 (red) and line #2 (black)
leads to outside terminals. Attach neutral wire (white)
to center terminal on the terminal block.
2
1
Remove supply cord strain relief
bracket and three supply cord mounting screws on
the terminal block.
Remove access door.
4
3
6
Reattach access door.
Feed supply cord up through hole in bottom
of range back.
Remove grounding screw. Cut-off
and discard ground strap.
6
5
Attach line #1 (red) and line #2 (black)
leads to outside terminals. Attach neutral wire (white)
to center terminal on terminal block.
Attach ground lead (green)
with ground screw that was removed.
18
19
Installation
Installation
Electrical Connection (4-wire) (cont.)
Leveling/Adjustments/Alignment (con’t)
7
1
4
3
8
”
3/8cm)
9
(0.
Check that unit is level side to
side and front to back. Side trim of the lowest corner
must be 3/8” (0.95 cm) above countertop.
Move unit into opening.
Reattach access door.
Push supply cord toward terminal
block to relieve strain, reattach supply cord strain
relief bracket over supply cord.
6
5
1
1
2
Leveling/Adjustments/Alignment
2
1
Measure the four corners in cutout area to verify if
flooring is level.
For uneven or sloped floors, level unit with metal shims
only, as the adjustment required may exceed
the thread available in the legs.
20
5
Lift unit and prop on wood blocks.
If leveling is required, move unit out of opening.
7
Set the high corner of range so that the top of side trim is
3/8” (0.95 cm) above countertop. Level range to high corner.
21
Installation
Installation
Anti-tip Device Installation (Wall Mount)
Anti-tip Device Installation (Floor Mount)
1
WARNING
1
2
1
TIPPING HAZARD
To reduce the risk of property
damage or personal injury;
install anti-tipping device
provided in accordance with
the installation instructions
in this document. Device
must be engaged properly to
prevent product from tipping
over.
2
1
21
12
(73. -7
83 c /8
m) ”
Me
as
ure
me
nt
Range
VGR “X”
VDR “X”
Width
Dimension
Di mens ion
36” 24-5/8” (62.5 cm) 23-1/2” (59.7 cm)
48” 22-3/4” (57.8 cm) 4-1/4” (10.8 cm)
1
(4201 6”
.16
cm
)
Ø
(A
)
Measure from floor to bottom
of the anit-tip opening located on the back of range.
This will be measurement (A).
2
1
(.3 /8”
2c
m)
Locate anti-tip bracket hook on the floor 16” 40.1 cm) from side
cabinet and 2-7/8” (7.3 cm) from rear wall. Mark and
drill 1/8” (.32 cm) holes where bracket will be located.
Mount anti-tip bracket hook to floor
using screws provided.
3
3
4
X
)
(A
nt )
e
rem4 cm
asu” (.6
e
M 1/4
+
1
x2
Locate anti-tip bracket on rear wall with the top left corner at
measurement (A) plus 1/2” (1.3 cm) from the floor and “X” from
where the right side of range (facing range) is to be located.
Mark and drill holes where bracket will be located.
2
1
2
Attach bracket to back of range using two screws.
Remove two screws from back of range.
Connecting Gas & Electric
1
4
DANGER
GAS LEAK HAZARD
To avoid risk of personal injury
or death; leak testing of the
appliance must be conducted
according to the manufacturer’s
instructions. Before placing appliance in
operation, always check for gas leaks
with soapy water solution.
• DO NOT USE AN OPEN FLAME TO
CHECK FOR GAS LEAKS.
Attach bracket with
mounting hardware provided.
22
Connect gas and electrical. Before placing appliance in operation,
always check for gas leaks. This must be performed by your
dealer, a qualified licensed plumber, or gas service company.
23
Installation
Installation
Standoff Spacer Removal
Door Replacement
DANGER
1
2
FIRE HAZARD
Backguards come standard with
standoff spacers which provide a barrier
between back of range and rear wall.
These must be in place for adequate
ventilation. Standoff spacers can only be
removed if range is installed against a
Non-Combustible wall.
1
1
2
Final Installation
Reattach door to range.
1a
1
Open door completely. Fold latches forward until
locked in place.
3
Slide range into place. Be sure
wall anit-tip bracket slides into the anit-tip opening
and floor anti-tip hook and bracket are engaged.
Close door.
3
2
”
3/8cm)
95
(0.
Burner heads and bases are packed in cardboard top pack with
the grates. Place burner bases on top of the burner flanges and
burner heads on top of the burner base. Place burner grate on
top of grate support.
Check that unit is level side to side
and front to back. The side trim must be 3/8” (0.95 cm)
above countertop. If unit is not level repeat Steps 5-7
of “Leveling/Adjustments/Alignment” section.
24
25
Final Preparation
• All stainless steel body parts should be
wiped with hot, soapy water and with a
liquid cleaner designed for this material.
If buildup occurs, DO NOT use steel wool,
abrasive cloths, cleansers, or powders!
If it is necessary to scrape stainless steel
Service & Registration
to remove encrusted materials, soak with
hot, wet cloths to loosen the material, then
use a wooden or nylon scraper. DO NOT
use a metal knife, spatula, or any other
material tool to scrape stainless steel!
Scratches are almost impossible to
remove.
Performance Checklist
A qualified installer should carry out the
following checks:
Contact Viking Range, LLC, 1-888-(845-4641), for the nearest service parts distributor in your
area or write to:
VIKING RANGE, LLC
PREFERRED SERVICE
111 Front Street
Greenwood, Mississippi 38930 USA
The serial number and model number for your appliance can be found
by opening the door and looking under the control panel. A duplicate
label is located on the back side of the range.
1-1/2”
• Check top burner ignition. See drawing
for proper flame height on HI. The low
flame should light at every port.
Only authorized replacement parts may be used in performing service on the appliance.
All servicing should be referred to a qualified technician.
(3.8 cm)
3/8”
(0.95 cm)
• Check oven bake function—bake burner on
full power.
Record the following information indicated below. You will need it if
service is ever required.
Model number ____________________________________________________________________________________
• Check convection bake function—bake
burner at full power with the convection
fan on.
Serial number _____________________________________________________________________________________
• Check broil function—broil burner at full
power.
Date of purchase __________________________________________________________________________________
Date installed ______________________________________________________________________________________
• Check convection broil function—broil
burner at full power with convection fan on.
Dealer's name _____________________________________________________________________________________
• Check convection fan function—convection
fan comes on when switch is turned on.
Address ___________________________________________________________________________________________
These installation instructions should remain with the unit
for future reference.
26
27
Download PDF

advertising