GE | GUD24GSSJWW | Quick Specs | GE GUD24GSSJWW Quick Specs

GUD24ESSJ/24GSSJ
GE® 24" Unitized Spacemaker® 2.0 DOE Cu. Ft. Washer and 4.4 Cu. Ft. Dryer
Dimensions and Installation Information (in inches)
Installation Instructions
Electrical Requirements:
GUD24ESSJ Electric Dryer – This appliance should be
connected to an individual, properly-grounded branch
circuit with 120/240V single-phase 60 Hz electrical
service and should be protected by 30-amp time-delay
fuses or circuit breakers. This appliance is manufactured
with neutral connected to the frame. Power cord should
be purchased separately.
24" NOMINAL PRODUCT DIMENSIONS
*23-3/4"
43"
17-7/8"
Note:
These appliances are not approved for 120-volt operation.
Gas Requirements:
GUD24GSSJ Gas Dryer – This appliance should be
connected to an individual branch circuit with a threeprong grounding-type receptacle and 120-volt singlephase 60 Hz electrical service and should be protected
by 15- or 20-amp time-delay fuses or circuit breakers.
This appliance is equipped with a 6-foot long flexible
U.L. listed 20-amp power cord to match a 15-amp
receptacle.
Gas Rated input 10,500 BTU/HR. Factory equipped for
natural gas. Tested for LP gas.
Dryers must be exhausted to the outside.
Installation Information:
For complete information, see installation instructions
packed with the product.
Gas Inlet
2-3/4"
Water Inlets
74-1/2"
Vent
8-1/4"
2"
51°
51"
Drain outlet
33-1/4"
32-7/8"
4-1/4"
27-3/8"
23-3/4"
19-1/8"
* Dimension represents door closed including handle and knobs.
NOTE: With feet set at mid position, feet can be adjusted ±.375".
For answers to your Monogram,® Cafe™ Series,
Profile™ Series or GE® appliance questions, visit
our website at geappliances.com or call GE
Answer Center® service, 800.626.2000.
Listed by
Underwriters
Laboratories
Specification Revised 2/15
GUD24ESSJ/24GSSJ
GE® 24" Unitized Spacemaker® 2.0 DOE Cu. Ft. Washer and 4.4 Cu. Ft. Dryer
Dimensions and Installation Information (in inches)
GUD24 DRYER EXHAUST LENGTH*
RECOMMENDED MAXIMUM LENGTH
Exhaust Hood Types
Use only for short
Recommended
run installations
4" DIA.
4" DIA.
4" DIA.
4"
No. of 90º
Elbows
0
1
2
2-1/2"
Rigid
Metal
43 Feet
33 Feet
24 Feet
For answers to your Monogram,® GE Profile™ or
GE® appliance questions, visit our website at
geappliances.com or call GE Answer Center®
service, 800.626.2000.
Rigid
Metal
36 Feet
26 Feet
16 Feet
For complete information, see installation instructions packed with your dryer.
Ducting Materials:
This dryer MUST be vented with 4" diameter all rigid metal exhaust duct.
Exhaust Length Calculation:
1.Determine the number of 90° turns needed for your installation. If you exhaust to the side or bottom of dryer,
add one turn.
2.The maximum length of 4" rigid (aluminum or galvanized) duct which can be tolerated is shown in the table.
For every extra 90° elbow, reduce the allowable vent system length by 10 ft.
Two 45° elbows will be treated like one 90° elbow.
For the side exhaust installations, add one 90° elbow to the chart.
The total vent system length includes all the straight portions and elbows of the system (transition duct
included).
Dryers must be exhausted to the outside.
Caution: For personal safety do not terminate exhaust into a chimney, under any enclosed house floor (crawl
space), or into an attic, since the accumulated lint could create a fire hazard or moisture could cause damage.
Never terminate the exhaust into a common duct or plenum with a kitchen exhaust, since the combination of lint
and grease could create a fire hazard.
Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird nesting, etc. The wall cap
must also be located at least 12" above the ground or any other obstruction with the opening pointed down.
Special Installation Requirements
Alcove or Closet Installation:
• If your dryer is approved for installation in an alcove or closet, it will be stated on a label on the dryer back.
• The dryer MUST be exhausted to the outside.
• Minimum clearances between dryer cabinet and adjacent walls or other surfaces are:
0" both sides and rear
1" front and top
• Minimum vertical space from floor to overhead cabinets, ceilings, etc. is 75-1/2".
• Closet doors must be louvered or otherwise ventilated and must contain a minimum of 60 sq. in. of open area
equally distributed. If this closet contains both a washer and a dryer, doors must contain a minimum of 120 sq. in.
of open area equally distributed.
• No other fuel-burning appliance shall be installed in the same closet with a gas dryer.
Bathroom or Bedroom Installation:
• The dryer MUST be exhausted to the outdoors.
• The installation must conform with the local codes, or in the absence of local codes, with the National Electric
Code and National Fuel Gas Code, ANSI Z223 for gas dryers.
Minimum Clearances other than Alcove or Closet Installation:
• Minimum clearances to combustible surfaces
0" both sides and rear
1" front and top
Listed by
Underwriters
Laboratories
Specification Revised 2/15
GUD24ESSJ/24GSSJ
GE® 24" Unitized Spacemaker® 2.0 DOE Cu. Ft. Washer and 4.4 Cu. Ft. Dryer
Features and Benefits
• Rotary-electromechanical controls (dryer) - Allow fast, easy cycle selection
• 12 wash cycles - Cycles are designed to specifically handle various
fabrics and soils
• 6 wash/rinse temperatures - Select the right temperature for ideal
wash results
• 1 wash/spin speed combinations - Speeds are matched to fabric type
for great clothes care
• Auto-load sensing - Washer will automatically measure the load size
and add just the right amount of water
• Rotary-electronic controls (washer) - Simplify cycle selection
• Bleach and fabric softener dispensers - Solutions are automatically mixed
with wash water for clean, bright, soft-to-the-touch results
• Cycle status lights - Easily see where your load is in the cleaning process
• Model GUD24ESSJWW – White on white (Electric)
• Model GUD24GSSJWW – White on white (Gas)
Modified Energy Factor (iMEF)
1.34
Water Factor (iWF)
8.0
GUD24ESSJ_GUD24GSSJ
Specification Revised 2/15
Download PDF

advertising