GE GTX42EASJWW Quick Specs
GTX42EASJ
GE® Series 6.2 Cu. Ft. Capacity Aluminized
Alloy Drum Electric Dryer with HE Sensor Dry
22 1/2"
26 3/4"
27"
Power Cord 4 1/2"
11 3/4"
Dimensions and Installation Information (in inches)
Electric Dryer Rating:
240V
5600W
24A
60Hz
208V
4400W 22A
60Hz
44"
37 1/2"
Exhaust Option: 4-way rear, right,
left and bottom
Circuit Requirements: An
individual, properly-grounded branch
circuit, protected by a 30-amp circuit
breaker or a time-delay fuse, is required.
Note: Dryer wall outlet must be
located within 36" of service cord entry
and acessible when dryer is mounted in
position.
Installation Information:
For complete information, see installation
instructions packed with your dryer.
4 1/4"
1 3/4"
4"
Side View
5"
3 1/4"
Rear View
Special Installation Requirements
Alcove or Closet Installation:
- I f your dryer is approved for installation in an alcove or closet, it will be stated on a label on
the dryer back.
-T
he dryer MUST be exhausted to the outside.
-M
inimum clearances between dryer cabinet and adjacent walls or other surfaces are:
0" either side; 3" front and rear
-M
inimum vertical space from floor to overhead cabinets, ceilings, etc. is 52".
-C
loset doors must be louvered or otherwise ventilated and must contain a minimum of 60 sq. in.
of open area equally distributed. If this closet contains both a washer and a dryer, doors must
contain a minimum of 120 sq. in. of open area equally distributed.
- No
other fuel-burning appliance shall be installed in the same closet with a gas dryer.
Bathroom or Bedroom Installation:
- The dryer MUST be exhausted to the outdoors.
- The installation must conform with the local codes, or in the absence of local codes, with the
National Electric Code and National Fuel Gas Code, ANSI Z223 for gas dryers.
Minimum Clearances other than Alcove or Closet Installation:
-M
inimum clearances to combustible surfaces are: 0" both sides; 3" rear
Dryer Exhausting Information­:
Use metal duct only, vertical and horizontal ducting.
For answers to your Monogram®, GE Profile™ Series or GE® Series appliance questions,
visit our website at geappliances.com or call GE Answer Center® service, 800.626.2000.
Listed by
Underwriters
Laboratories
Specification Created 7/15
GTX42EASJ
GE® Series 6.2 Cu. Ft. Capacity Aluminized
Alloy Drum Electric Dryer with HE Sensor Dry
For complete information, see installation instructions
packed with your dryer.
Ducting Materials:
For best performance, this dryer should be vented with 4" diameter all
rigid metal exhaust duct. If rigid metal duct cannot be used, then UL-listed
flexible metal (semi-rigid) ducting can be used (Kit WX08X10077). In special
installations, it may be necessary to connect the dryer to the house vent using
a flexible metal (foil-type) duct. A UL-listed flexible metal (foil-type) duct
may be used ONLY in installations where rigid metal or flexible metal (semirigid) ducting cannot be used AND where a 4” diameter can be maintained
throughout the entire length of the transition duct. Please see installation
instruction packed with your dryer for complete instructions when using flexible
metal (foil type) ducting.
Exhaust Length Calculation:
1.Determine the number of 90° turns needed for your installation. If you
exhaust to the side or bottom of dryer, add one turn.
2.The maximum length of 4" rigid (aluminum or galvanized) duct which can
be tolerated is shown in the table. A turn of 45° or less may be ignored. Two
45° turns within the duct length should be treated as a 90° elbow. A turn
over 45° should be treated as a 90° elbow.
Dryers must be exhausted to the outside.
Caution: For personal safety do not terminate exhaust into a chimney, under
any enclosed house floor (crawl space), or into an attic, since the accumulated
lint could create a fire hazard or moisture could cause damage. Never terminate
the exhaust into a common duct or plenum with a kitchen exhaust, since the
combination of lint and grease could create a fire hazard.
Exhaust ducts should be terminated in a dampered wall cap to prevent back
drafts, bird nesting, etc. The wall cap must also be located at least 12" above
the ground or any other obstruction with the opening pointed down.
For more information on venting kits and accessories,
please call 1-800-GE-CARES.
Dryer exhausting information—
use metal duct only vertical and
horizontal ducting
Best performance
A
A 4
B
A
4
2-1/2
Domestic dryer
B models
2-1/2
GE Frontload Long Vent 7.0
cu. ft. capacity electric dryer
(GFDL)
Long Vent 6.0 - 8.0 cu. ft.
capacity electric & gas dryers
(GTDL and GTV)
Long Vent 6.1-7.4 cu. ft.
capacity electric & gas
(GTD42, GTD45, GTD65,
GTX42 and GTX65)
All 6.0 - 8.3 cu. ft. capacity
models electric and gas dryers
(GFDS, GFDR, GFDN, GTDS,
GTDN, GHDN, GHDS, GTDP,
GLDP, GTD, HTDP, HTDX)
DCVH480
All 3.6 cu. ft. (DSKS, DSKP)
electric dryers
Laundry Center GUD27
Laundry Center GUD24
For answers to your Monogram®, GE Profile™ Series or GE® Series appliance questions,
visit our website at geappliances.com or call GE Answer Center® service, 800.626.2000.
Maximum length
of 4" dia rigid
metal duct
Exhaust hood type
Number
A
B
of 90°
4"
2-1/2"
turns
opening opening
0
200 ft.
175 ft.
1
185 ft.
2
175 ft.
165 ft.
155 ft.
3
165 ft.
145 ft.
4
155 ft.
135 ft.
5
145 ft.
125 ft.
0
1
2
3
4
5
0
1
2
3
4
5
0
150 ft.
135 ft.
125 ft.
115 ft.
105 ft.
95 ft.
120 ft.
100 ft.
85 ft.
70 ft.
60 ft.
55 ft.
90 ft.
125 ft.
115 ft.
105 ft.
95 ft.
85 ft.
75 ft.
90 ft.
75 ft.
65 ft.
55 ft.
45 ft.
35 ft.
60 ft.
1
2
3
4
0
1
2
3
0
60 ft.
45 ft.
35 ft.
25 ft.
90 ft.
60 ft.
45 ft.
35 ft.
46 ft.
45 ft.
35 ft.
25 ft.
15 ft.
60 ft.
45 ft.
35 ft.
25 ft.
37 ft.
1
2
3
0
37 ft.
30 ft.
23 ft.
56 ft.
30 ft.
22 ft.
15 ft.
42 ft.
1
2
3
0
1
2
48 ft.
40 ft.
32 ft.
43 ft.
33 ft.
24 ft.
34 ft.
26 ft.
18 ft.
36 ft.
26 ft.
16 ft.
Specification Created 7/15
GTX42EASJ
GE® Series 6.2 Cu. Ft. Capacity Aluminized
Alloy Drum Electric Dryer with HE Sensor Dry
Features and Benefits
Auto Dry – For clothes that come out feeling and looking great, this setting
monitors air temperature to set the optimal drying time
Wrinkle Care extended tumble – Reduces wrinkling and creasing
End-of-cycle signal – Alerts you when the load is done, so clothes can be
removed before wrinkles set in
4 heat selections – Provide the right temperatures for your clothes-drying needs
Up to 120 ft. venting capability – Provides flexible installation
Model GTX42EASJWW – White
GTX42EASJWW_GTX42GASJWW_GTD42EASJ_GTD42GASJ
For answers to your Monogram®, GE Profile™ Series or GE® Series appliance questions,
visit our website at geappliances.com or call GE Answer Center® service, 800.626.2000.
Specification Created 7/15
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement