GE | GUD24ESSMWW | Specification Sheet | GE GUD24ESSMWW Specification Sheet

GUD24ESSM/24GSSM
GE® Unitized Spacemaker® 2.3 DOE Cu. Ft. Stainless Steel Washer and 4.4 Cu. Ft. Dryer
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
ELECTRICAL REQUIREMENTS:
GUD24ESSM Electric Dryer – This appliance should be
connected to an individual, properly-grounded branch
circuit with 120/240V single-phase 60 Hz electrical
service and should be protected by 30-amp time-delay
fuses or circuit breakers. This appliance is manufactured
with neutral connected to the frame. Power cord should
be purchased separately.
Installation Instructions
24" NOMINAL PRODUCT DIMENSIONS
*24-5/8"
NOTE: These appliances are not approved for 120-volt
operation.
GAS REQUIREMENTS:
GUD24GSSM Gas Dryer – This appliance should be
connected to an individual branch circuit with a threeprong grounding-type receptacle and 120-volt singlephase 60 Hz electrical service and should be protected
by 15- or 20-amp time-delay fuses or circuit breakers.
This appliance is equipped with a 6-foot long flexible
U.L. listed 20-amp power cord to match a 15-amp
receptacle.
43"
18"
INSTALLATION INFORMATION: For complete
information, see installation instructions packed with
the product.
2-3/4"
Water Inlets
74-7/8"
Vent
8-5/8"
2"
51°
51-3/8"
GAS RATED input 10,500 BTU/HR. Factory equipped
for natural gas. Tested for LP gas.
Dryers must be exhausted to the outside.
Gas Inlet
37-1/4"
Drain outlet
33-7/8"
32-3/4"
4-1/4"
27-3/8"
23-3/4"
21-1/8"
* Dimension represents door closed including handle and knobs.
NOTE: With feet set at mid position, feet can be adjusted +/- 3/8".
Listed by
Underwriters
Laboratories
For answers to your Monogram, GE Café™ Series, GE Profile™ Series or
GE Appliances product questions, visit our website at geappliances.com
or call GE Answer Center® Service, 800.626.2000.
Specification Revised 11/17
GUD24ESSM/24GSSM
GE® Unitized Spacemaker® 2.3 DOE Cu. Ft. Stainless Steel Washer and 4.4 Cu. Ft. Dryer
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
For complete information, see installation instructions packed with
your dryer.
DUCTING MATERIALS: This dryer MUST be vented with
4" diameter all rigid metal exhaust duct.
EXHAUST LENGTH CALCULATION:
1. Determine the number of 90° turns needed for your installation. If
you exhaust to the side or bottom of dryer, add one turn.
GUD24 DRYER EXHAUST LENGTH*
RECOMMENDED MAXIMUM LENGTH
Exhaust Hood Types
Use only for short
Recommended
run installations
2. The maximum length of 4" rigid (aluminum or galvanized) duct
which can be tolerated is shown in the table.
For every extra 90° elbow, reduce the allowable vent system length
by 10 ft. Two 45° elbows will be treated like one 90° elbow. For the
side exhaust installations, add one 90° elbow to the chart. The total
vent system length includes all the straight portions and elbows of the
system (transition duct included).
4" DIA.
4" DIA.
4"
Dryers must be exhausted to the outside.
CAUTION: For personal safety do not terminate exhaust into a
chimney, under any enclosed house floor (crawl space), or into an
attic, since the accumulated lint could create a fire hazard or moisture
could cause damage. Never terminate the exhaust into a common duct
or plenum with a kitchen exhaust, since the combination of lint and
grease could create a fire hazard.
4" DIA.
No. of 90º
Elbows
0
1
2
2-1/2"
Rigid
Metal
43 Feet
33 Feet
24 Feet
Rigid
Metal
36 Feet
26 Feet
16 Feet
Exhaust ducts should be terminated in a dampered wall cap to prevent
back drafts, bird nesting, etc. The wall cap must also be located at
least 12" above the ground or any other obstruction with the opening
pointed down.
Listed by
Underwriters
Laboratories
For answers to your Monogram, GE Café™ Series, GE Profile™ Series or
GE Appliances product questions, visit our website at geappliances.com
or call GE Answer Center® Service, 800.626.2000.
Specification Revised 11/17
GUD24ESSM/24GSSM
GE® Unitized Spacemaker® 2.3 DOE Cu. Ft. Stainless Steel Washer and 4.4 Cu. Ft. Dryer
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
Special Installation Requirements
ALCOVE OR CLOSET INSTALLATION:
– If your dryer is approved for installation in an alcove or closet, it will
be stated on a label on the dryer back.
– The dryer MUST be exhausted to the outside.
– Minimum clearances between dryer cabinet and adjacent walls or
other surfaces are: 0" both sides and rear, 1" front and top
GUD24 DRYER EXHAUST LENGTH*
RECOMMENDED MAXIMUM LENGTH
Exhaust Hood Types
Use only for short
Recommended
run installations
– Minimum vertical space from floor to overhead cabinets, ceilings, etc.
is 75-1/2".
– Closet doors must be louvered or otherwise ventilated and must
contain a minimum of 60 sq. in. of open area equally distributed. If
this closet contains both a washer and a dryer, doors must contain a
minimum of 120 sq. in. of open area equally distributed.
4" DIA.
4" DIA.
– No other fuel-burning appliance shall be installed in the same close
with a gas dryer.
BATHROOM OR BEDROOM INSTALLATION:
– The dryer MUST be exhausted to the outdoors.
– The installation must conform with the local codes, or in the absence
of local codes, with the National Electric Code and National Fuel Gas
Code, ANSI Z223 for gas dryers.
4" DIA.
4"
No. of 90º
Elbows
0
1
2
2-1/2"
Rigid
Metal
43 Feet
33 Feet
24 Feet
Rigid
Metal
36 Feet
26 Feet
16 Feet
MINIMUM CLEARANCES OTHER THAN ALCOVE OR CLOSET
INSTALLATION:
– Minimum clearances to combustible surfaces:
0" both sides and rear
1" front and top
Listed by
Underwriters
Laboratories
For answers to your Monogram, GE Café™ Series, GE Profile™ Series or
GE Appliances product questions, visit our website at geappliances.com
or call GE Answer Center® Service, 800.626.2000.
Specification Revised 11/17
GUD24ESSM/24GSSM
GE® Unitized Spacemaker® 2.3 DOE Cu. Ft. Stainless Steel Washer and 4.4 Cu. Ft. Dryer
FEATURES AND BENEFITS
Rotary-electromechanical controls (dryer) – Allow fast, easy cycle selection
12 wash cycles – Cycles are designed to specifically handle various
fabrics and soils
wash/rinse temperatures – Select the right temperature for ideal
6
wash results
1 wash/spin speed combinations – Speeds are matched to fabric type
for great clothes care
Auto-load sensing – Washer will automatically measure the load size
and add just the right amount of water
Rotary-electronic controls (washer) – Simplify cycle selection
Bleach and fabric softener dispensers – Solutions are automatically mixed
with wash water for clean, bright, soft-to-the-touch results
Cycle status lights – Easily see where your load is in the cleaning process
Model GUD24ESSMWW – White on white (Electric)
Model GUD24GSSMWW – White on white (Gas)
GUD24ESSMWW
GUD24GSSMWW
Specification Revised 11/17
Download PDF

advertising