GE | GFDN160GJWW | Quick Specs | GE GFDN160GJWW Quick Specs

GFDN160GJ
GE® Series 7.5 Cu. Ft. Capacity Front Load Gas Dryer
Dimensions and Installation Information (in inches)
Gas Dryer Rating
120V
27
33
60Hz, 6A
Exhaust Options: 3-way via rear, left, and
bottom.
Circuit Requirements: An individual,
properly grounded branch circuit, protected by a
15-20 amp circuit breaker or a time-delay fuse, is
required.
39-3/8
Note: Dryer wall outlet must be located within 36"
of service cord entry and accessible when dryer is
mounted in position.
Installation Information: For complete
information, see installation instructions packed with
your dryer.
4-3/8
5-3/8
For answers to your Monogram,® GE Profile™
or GE® appliance questions, visit our website
at geappliances.com or call GE Answer Center®
service, 800.626.2000.
Specification Created 3/15
GFDN160GJ
GE® Series 7.5 Cu. Ft. Capacity Front Load Gas Dryer
Special Installation Requirements
Stacked Dimensions (in inches)
Stacked Installation:
Brackets for stacking dryer over washer are not included with the
washer. Order part no. GEFLSTACK or part no. WE25X10018.
50-5/8
24-7/8
3-1/2
3
Alcove or Closet Installation:
• If your dryer is approved for installation in an alcove or closet, it
will be stated on a label on the dryer back.
• The dryer MUST be exhausted to the outside.
39-3/8
• Minimum clearances between dryer cabinet and adjacent walls
or other surfaces are: 0" either side, 3" front and rear
• Minimum vertical space from floor to overhead cabinets,
ceilings, etc. is 52".
• Closet doors must be louvered or otherwise ventilated and must
contain a minimum of 60 sq. in. of open area equally distributed. If
this closet contains both a washer and a dryer, doors must contain a
minimum of 120 sq. in. of open area equally distributed.
• No other fuel-burning appliance shall be installed in the same closet
with a gas dryer.
Bathroom or Bedroom Installation:
• The dryer MUST be exhausted to the outdoors.
• The installation must conform with the local codes, or in the absence
of local codes, with the National Electric Code and National Fuel Gas
Code, ANSI Z223 for gas dryers.
Minimum Clearance other than Alcove or Closet
Installations:
• Minimum clearances to combustible surfaces 0" both sides, 3" rear.
Pedestal Dimensions
(in inches)
SBSD137HWW - white
This optional 13" pedestal
raises the door opening and
height of the washer or dryer.
Feet on 13" pedestal allow it to
adjust to 13-3/8" height.
27
13
For more information on venting kits and accessories, please
call 1-800-GE-CARES.
28-3/4
For answers to your Monogram,® GE Profile™
or GE® appliance questions, visit our website
at geappliances.com or call GE Answer Center®
service, 800.626.2000.
Specification Created 3/15
GFDN160GJ
GE® Series 7.5 Cu. Ft. Capacity Front Load Gas Dryer
Dryer Exhausting Information – Metal Duct Only
For complete information, see installation instructions packed with your dryer.
Ducting Materials: For best performance, this dryer should be vented with 4"
diameter all rigid metal exhaust duct. If rigid metal duct cannot be used, then UL-listed
flexible metal (semi-rigid) ducting can be used (Kit WX08X10077). In special installations,
it may be necessary to connect the dryer to the house vent using a flexible metal (foil-type)
duct. A UL-listed flexible metal (foil-type) duct may be used ONLY in installations where
rigid metal or flexible metal (semi-rigid) ducting cannot be used AND where a 4" diameter
can be maintained throughout the entire length of the transition duct. Please see installation
instruction packed with your dryer for complete instructions when using flexible metal (foil
type) ducting.
Best performance
Maximum length of 4"
dia. rigid metal duct
Exhaust hood type
A
A
4
B
Domestic
dryer models
2-1/2
Exhaust Length Calculation:
1. Determine the number of 90° turns needed for your installation. If you exhaust to the
side or bottom of dryer, add one turn.
2. T
he maximum length of 4' rigid (aluminum or galvanized) duct which can be tolerated is
shown in the table.
7.5 cu. ft.
capacity models
gas dryers
Number
of
90°
turns
0
1
2
3
4
A
4"
opening
90 ft.
60 ft.
45 ft.
35 ft.
25 ft.
B
2-1/2"
opening
60 ft.
45 ft.
35 ft.
25 ft.
15 ft.
A turn of 45° or less may be ignored. Two 45° turns within the duct length should be
treated as a 90° elbow.
A turn over 45° should be treated as a 90° elbow.
Dryers must be exhausted to the outside.
Caution: For personal safety do not terminate exhaust into a chimney, under any
enclosed house floor (crawl space), or into an attic, since the accumulated lint could create
a fire hazard or moisture could cause damage. Never terminate the exhaust into a common
duct or plenum with a kitchen exhaust, since the combination of lint and grease could create
a fire hazard.
Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird
nesting, etc. The wall cap must also be located at least 12" above the ground or any other
obstruction with the opening pointed down.
For more information on venting kits and accessories, please call 1-800-GE-CARES.
2-1/2
For answers to your Monogram,® GE Profile™
or GE® appliance questions, visit our website
at geappliances.com or call GE Answer Center®
service, 800.626.2000.
3-1/2
1-3/4 Gas Pipe Electrical
12
Connection Connection
Specification Created 3/15
GFDN160GJ
GE® Series 7.5 Cu. Ft. Capacity Front Load Gas Dryer
Features and Benefits
HE Sensor Dry – Keep your clothes looking and feeling their best. Dual
thermistors continually monitor temperature with a sensor bar that measures
moisture to prevent over-drying
Quick Dry – Quickly dries items and small loads for families on the go
Damp Dry – Allows you set an alert to remove select items for hang-drying
or damp ironing
Dura Drum – Provideds long lasting durability
Delay start – Set the dryer to begin cycles whenever it’s convenient for you
Bulky Bedding cycle – Dries larger items, such as comforters, blankets and jackets
Model GFDN160GJWW – White
GFDN160GJWW_GFDN160EJWW
For answers to your Monogram,® GE Profile™
or GE® appliance questions, visit our website
at geappliances.com or call GE Answer Center®
service, 800.626.2000.
Specification Created 3/15
Download PDF

advertising