Dacor | DYWS4 | Installation Instructions Trim Kit Installs [1.12 MB] | Dacor DYWS4 Installation Instructions Trim Kit Installs [1.12 MB]

WINE DISPENSING SYSTEM MODEL: DYWS4
INSTALLATION
INSTRUCTIONS
Trim Kit
Part Number AWSTK24
IMPORTANT: The wine dispensing utilizes a thermo-electric cooling system that can normally
cool the bottle bay to a temperature 25°F less than the ambient air outside the unit. This trim kit
limits system air circulation slightly, limiting the cooling capability to 22°F less than ambient. Be
sure that this limitation is acceptable before installing this kit.
Parts Included with kit
(8) #8 x 3/8 Phillips
head screws (PN 83263)
(9) #10 x 1/2 Phillips
head screws (PN 83022)
(8) Flat head Phillips head
screws (PN 107578)
Top trim bracket
(8) Fiber washers
(PN 83555)
(2) Base supports
(1) Base divider
Top trim
piece*
Bottom left trim
bracket
Left trim
piece
Bottom right trim
bracket
Right trim
piece
Bottom
trim piece*
Foam Strips
(1 long, 2 short)
*The top and bottom trim pieces are identical, but
installed in the opposite orientation from each other.
Part No. 107554 Rev. A
Wine Dispensing System Trim Kit Instructions
Tools Required
Tape measure
Phillips head
screwdriver
Pencil
Drill with 3/32” drill bit
(for drilling pilot holes)
Introduction
For proper fit, the cutout dimensions
shown are required. The spacing above
and below the cutout are critical for
ventilation purposes. Failure to provide
proper ventilation will result in poor wine
cooling. Consult the Wine Dispensing
System Installation Instructions
for additional cabinet requirements
(electrical requirements etc.).
1 1/2” min.
(3.8 cm)
29”
(73.7 cm)
21”
(53.3 cm)
1 5/8” min.
(4.1 cm)
both sides
24” min.
(61.0 cm)
1 1/2” min.
(3.8 cm)
Page 2
Wine Dispensing System Trim Kit Instructions
Installation Instructions
STEP 1
Peel the protective backing off of the longest of the 3 foam strips and attached it to the base divider as shown.
STEP 2
Attach the (2) base pieces to the base divider using (4) #8 x 3/8 screws. The
foam strip attached in step 1 goes toward the base pieces as shown below.
Foam strip
Base Assembly
Page 3
Wine Dispensing System Trim Kit Instructions
STEP 3
Insert the base assembly, assembled in step 1, into the cutout with the divider toward
the back. Center it left to right in the cutout using a ruler or tape measure.
STEP 4
Using a pencil, mark 4 pilot hole locations in the front of the cabinet.
STEP 5
Drill 4 pilot holes for the base assembly using a 3/32” drill bit.
STEP 6
Attach the base assembly to the front of the cabinet using (4) #10 x 1/2 Phillips head
screws.
Cutout
Base assembly
(divider toward back)
Base Installation
Page 4
Wine Dispensing System Trim Kit Instructions
STEP 7
Attach the bottom left and bottom right trim brackets to the front of the base assembly
as shown, using (4) #8 x 3/8 screws.
Base
assembly
Bottom left
trim bracket
Bottom right
trim bracket
Bottom Trim Bracket Installation
STEP 8
Attach the bottom left and bottom right trim brackets to the front of the cabinet using
(2) #10 x 1/2 Phillips head screws.
Attach Bottom Trim Brackets to Cabinet
Page 5
Wine Dispensing System Trim Kit Instructions
STEP 9
Hold the top trim bracket in the mounting position on the top edge of the cutout. Center it using a ruler or tape measure
STEP 10
While holding the trim bracket in place, using a pencil, mark 3 pilot hole locations in the underside of the top of the cabinet cutout.
STEP 11
Drill 3 pilot holes for the top trim bracket using a 3/32” drill bit.
STEP 12
Attach the top trim bracket to the top front of the cabinet using (3) #10 x 1/2
Phillips head screws.
Top trim
bracket
Cutout
Top Trim Bracket Installation
Page 6
Wine Dispensing System Trim Kit Instructions
WARNING: Excessive weight hazard - Use two or more people to move and install the wine
dispensing system. Failure to do so can result in back or other injury.
STEP 13
With the help of at least one other person, place the wine dispensing system
close the the cabinet cutout. Connect the power supply and the gas supply
line according to the Wine Dispensing System Installation Instructions. Adjust the leveling legs to 1 inch in height. NOTE: The trim and the wine dispensing system will not line up properly if the legs are not adjusted to 1 inch.
STEP 14
Peel the protective backing off of the short foam strips included with the kit
and attached them to the sides of the wine dispensing system at the bottom of
the side panel. Leave a 1 inch gap between the front of the unit and the edge
of each foam strip (see below).
STEP 15
With the help of at least one other person, lift the wine dispensing system into
the cutout. Be sure that the foam strips on the sides do not pull loose. The
legs on the wine dispensing system go on top of the base supports.
STEP 16
Center the wine dispensing system left to right in the cutout using a ruler or
tape measure. The front of the system needs to protrude from the front of the
cabinet 1 inch.
1 Inch
(2.5 cm)
Foam strip,
2 places
1 Inch
(2.5 cm)
1 Inch
(2.5 cm)
Foam Strip Installation - Step 14
System Installation - Steps 15 and 16
Page 7
STEP 14
Assemble the front trim pieces as shown below. Insert the tabs on the top and
bottom pieces into the slots on the side pieces.
STEP 15
Install the trim using the (8) flat head screws included with the kit. Insert the
fiber washers between the trim and the mounting brackets as needed for a
good fit.
Fiber washers,
use as necessary
Flathead screw,
8 places
Insert tabs
into slots
Trim Assembly and Installation
Dacor ● 14425 Clark Avenue, City of Industry, CA 91745 ● Phone: (800) 793-0093 ● Fax: (626) 403-3130 ● www.dacor.com
Download PDF

advertising