Kenmore | 22-80322 | Installation Instruction | Kenmore 22-80322 Installation Instruction

Kenmore 22-80322 Installation Instruction
Installation
Instructions
Questions? Call 1-800-4-MY-HOME®
Over the Range
Microwave Oven
or Visit our Website at: http://www.kenmore.com
BEFORE YOU BEGIN
Read these instructions completely and carefully.
IMPORTANT –
•
Save these
instructions for local inspector’s use.
•
IMPORTANT –
Observe all
governing codes and ordinances.
• Note to Installer – Be sure to leave these
instructions with the Consumer.
Note to Consumer – Keep these
instructions for future reference.
• Skill level – Installation of this appliance requires
basic mechanical and electrical skills.
• Proper installation is the responsibility of the installer.
• Product failure due to improper installation is not
covered under the Warranty.
•
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
p/n 316495111
May 2013
Installation Instructions
CONTENTS
Adapting Microwave Blower
for Outside Back Exhaust................17– 18
General information
Mount the Microwave Oven ................19
Important Safety Instructions .................................. 3
C
Electrical Requirements .......................................... 3
Recirculating ........................................ 20 – 22
Attach Mounting Plate to Wall ............20
Damage – Shipment/Installation.............................. 4
Preparation of Top Cabinet ................21
Parts Included.......................................................... 4
Check Blower Plate ............................ 21
Tools You Will Need ................................................ 5
Mount the Microwave Oven ..........21– 22
Mounting Space ...................................................... 5
Installing or Change the
Charcoal Filter ....................................22
Step-by-step installation guide
Before You Use Your Microwave .......................... 23
Placement of The Mounting Plate ...................... 6–8
Template Information............................................. 24
Removing the Mounting Plate ...................... 6
Finding the Wall Studs .................................. 6
Determining Wall Plate Location .................. 7
Aligning the Wall Plate ................................ 8
Installation Types............................................... 9–22
Hood Exhaust .................................................. 10 –11
A Outside Top Exhaust ............................ 12–15
Attach Mounting Plate to Wall............12
Preparation of Top Cabinet................13
Adapting Microwave Blower for
Outside top Exhaust .................. 13–14
Checking for Proper Damper
Operation ............................................14
Mount the Microwave Oven ..........14 –15
Adjust the Exhaust Adaptor ................15
Connecting Ductwork..........................15
B Outside Back Exhaust ............................ 16–19
Preparing Rear Wall for
Outside Back Exhaust..........................16
Remove Blower Plate ..............................16
Attach Mounting Plate to Wall ............17
Preparation of Top Cabinet ................17
EN-2
Installation Instructions
IMPORTANT SAFETY INSTRUCTIONS
You should have the wall receptacle and circuit checked
by a qualified electrician to make sure the receptacle is
properly grounded.
This product requires a three-prong grounded outlet.
The installer must perform a ground continuity check
on the power outlet box before beginning the
installation to ensure that the outlet box is properly
grounded. If not properly grounded, or if the outlet
box does not meet electrical requirements noted
(under ELECTRICAL REQUIREMENTS), a qualified
electrician should be employed to correct any
deficiencies.
CAUTION: For personal
safety, remove house fuse
or open circuit breaker
before beginning
installation to avoid severe
or fatal shock injury.
Where a standard two-prong wall receptacle is
encountered, it is very important to have it replaced
with a properly grounded three-prong wall receptacle,
installed by a qualified electrician.
DO NOT, UNDER ANY CIRCUMSTANCES, CUT,
DEFORM OR REMOVE ANY OF THE PRONGS
FROM THE POWER CORD. DO NOT USE WITH
AN EXTENSION CORD.
ELECTRICAL
REQUIREMENTS
Product rating is 120 volts AC, 60 Hertz, 15 amps and
1.6 kilowatts. This product must be connected to a
supply circuit of the proper voltage and frequency.
Wire size must conform to the requirements of the
National Electrical Code or the prevailing local
code for this kilowatt rating. The power supply
cord and plug should be brought to a separate
15- to 20- ampere branch circuit single grounded
outlet. The outlet box should be located in the
cabinet above the microwave oven. The outlet box
and supply circuit should be installed by a qualified
electrician and conform to the National Electrical
Code or the prevailing local code.
CAUTION: For personal safety, the mounting surface
must be capable of supporting the cabinet load, in
addition to the added weight of this 63–85 pound
(28.5–38.5 kg) product, plus additional oven loads of
up to 50 pounds (22.7 kg) or a total weight of
113–135 pounds (51.3–61.2 kg).
CAUTION: For personal safety, this product cannot
be installed in cabinet arrangements such as an island or
a peninsula. It must be mounted to BOTH a top cabinet
AND a wall.
NOTE: For easier installation and personal safety, it is
recommended that two people install this product.
IMPORTANT – PLEASE READ CAREFULLY. FOR
PERSONAL SAFETY, THIS APPLIANCE MUST BE
PROPERLY GROUNDED TO AVOID SEVERE OR
FATAL SHOCK.
The power cord of this
appliance is equipped with a
three-prong (grounding)
plug which mates with a
standard three-prong
(grounding) wall receptacle
to minimize the possibility
of electric shock hazard
from this appliance.
Ensure proper
ground exists
before use
EN-3
Installation Instructions
PARTS INCLUDED
DAMAGE—SHIPMENT/
INSTALLATION
ADDITIONAL PARTS
• If the unit is damaged in shipment, return the
PART
unit to the store in which it was bought for repair
or replacement.
• If the unit is damaged by the customer, repair or
replacement is the responsibility of the customer.
• If the unit is damaged by the installer (if other
than the customer), repair or replacement must
be made by arrangement between customer
and installer.
INSTALL
AT
INSTRUC ION
TIONS
PARTS INCLUDED
HARDWARE PACKET
PART
QUANTITY
Wood Screws
(1⁄4“ x 2“)
2
Toggle Bolts (and
wing nuts) (3⁄16“ x 3“)
2
Self-Aligning Machine
Screws (1⁄4“-28 x 31⁄4“)
3
Nylon Grommet
(for metal cabinets)
1
(CONT.)
You will find the installation hardware contained in
a packet with the unit. Check to make sure you have
all these parts.
NOTE: Some extra parts are included.
QUANTITY
USE &
C
MANUAARE
L
Top Cabinet
Template
1
Rear Wall
Template
1
Installation
Instructions
1
Use & Care
Manual
1
Separately
Packed
Grease
Filters
2
Exhaust
adaptor
1
Glass
Tray
1
Turntable
Ring
1
Convection
wire rack
1
Shelf
1
For some models
EN-4
Installation Instructions
TOOLS YOU WILL NEED
Pencil
# 1 Phillips screwdriver
Tin snips (for cutting
damper, if required)
Ruler or tape measure and
straight edge
Scissors
(to cut template, if necessary)
Electric drill with 3⁄16“, 1⁄2“ and 5⁄8“
drill bits
Carpenter square
(optional)
Filler blocks or scrap
wood pieces, if needed
for top cabinet spacing
(used on recessed bottom
cabinet installations only)
Gloves
Saw (saber, hole or keyhole)
Stud finder or
Safety goggles
Hammer (optional)
Duct and masking tape
Level
MOUNTING SPACE
16 1⁄ 2“ (41.9 cm)
Bottom Edge of
Cabinet Needs to
be 30w (76.2 cm)
or More from the
Cooking Surface
13“ Maximum (33 cm)
30“ (76.2 cm)
2“ (5.1 cm)
30“
(76.2 cm)
min.
Backsplash
66w (167.6 cm)
or More from
the Floor to the
Top of the
Microwave
NOTES:
• The space between the cabinets must be
30“ (76.2 cm)wide and free of obstructions.
• If you are going to vent your microwave oven
to the outside, see Hood Exhaust Section for
exhaust duct preparation.
• When installing the microwave oven beneath
smooth, flat cabinets, be careful to follow the
instructions on the top cabinet template for
power cord clearance.
• As a guide to installation, see page 24 for Mounting
Template Information.
• If the cabinet depth including the cabinet doors
is more than 13'"' then the unit must be spaced
out from wall using adequate materials supporting
150 Ibs to allow proper top vent air exhaust.
Cabinet
EN-5
Cabinet
Installation Instructions
1 PLACEMENT OF THE MOUNTING PLATE
4 Cut the middle of the outer protective plastic bag to
remove the mounting plate
A. REMOVING THE MICROWAVE
OVEN FROM THE CARTON/
REMOVING THE MOUNTING
PLATE
Screws
Screws
Mounting Plate
1 Remove the installation instructions,use and care,
exhaust adapter, turntable ring, shelf, filters, glass
tray and the small hardware bag. Do not remove
the Styrofoam protecting the front of the oven.
Small Hardware Bag
Exhaust Adapter
Filters and Turntable
Ring below glass tray
5 Remove the screws from each end of the mounting
plate. This plate will be used as the rear wall template
and for mounting. Reinstall the screws into the holes
where they were removed.
B. FINDING THE WALL STUDS
Shelf
Glass Tray
2 Fold back all 4 carton flaps fully against carton
sides. Then carefully roll the oven and carton over
onto the top side. The oven should be resting in
the Styrofoam.
Wall
Studs
Center
Carton
1 Find the studs, using one of the following
methods:
A. Stud finder – a magnetic device which
locates nails.
B. Use a hammer to tap lightly across the
mounting surface to find a solid sound.
This will indicate a stud location.
2 After locating the stud(s), find the center by
probing the wall with a small nail to find the edges
of the stud. Then place a mark halfway between
the edges. The center of any adjacent studs should
be 16w (40.6 cm) or 24w (61 cm) from this mark.
3 Draw a line down the center of the studs.
THE MICROWAVE MUST BE CONNECTED TO
AT LEAST ONE WALL STUD.
Styrofoam
3 Pull the carton up and off the oven.
EN-6
Installation Instructions
C. DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET
Plate position-beneath framed
recessed cabinet bottom
Plate position-beneath flat bottom
cabinet
NOTE:
IT IS VERY
READ
IMPORTAN
AND FOLLOW
IN THE
T TO
INSTALLAT THE DIRECTION
BEFORE
ION INSTRUCT
PROCEED
S
REAR
ING
WALL
IONS
TEMPLATE WITH THIS
This Rear
Wall
.
Template
mounting
serves
plate and
outlet.
to position
to locate
the horizontal the bottom
1. Use
a level
exhaust
accurately. to check that
the template
2. Locate
is positioned
and
right side mark at least
 of the centerline.one stud on the
It is important
left or
screw mounted
to use at
least one
of the microwave.
firmly in
a stud to
wood
locations
support
Mark two
for the supplied
additional, the weight
3. Drill holes
toggle bolts. evenly spaced
in the marked
a stud,
drill a 3/16"
locations.
that do
Where
hole for
not
wood screws. there is
toggle bolts.line up with
a stud,
drill 5/8" For holes

holes for
DO NOT
AT THIS
INSTALL
TIME.
THE MOUNTING
4. Remove
PLATE
5. Review the template
from the
the
rear wall.
installation Installation
situation. Instruction
book for
your
Darle vuelta
a la hoja
versión
para
en Español.
consultar



Locate
and
mounting mark holes to
align with
plate.
IMPORTAN
holes in
the
LOCATE T:
AT LEAST
THE CENTERLI
ONE STUD
ON EITHER
NE.
MARK
THE
SIDE OF
SPACED LOCATION
FOR 2
TOGGLE
ADDITIONA
AREA.
BOLTS
L, EVENLY
IN THE
MOUNTING
PLATE
Trim the
rear wall
template
along
NOTE:
IT IS VERY
READ
IMPORTAN
AND FOLLOW
IN THE
T TO
THE DIRECTIO
INSTALLA
BEFORE
TION INSTRUCT
NS
PROCEED
REAR
ING
IONS
WALL
TEMPLATE WITH THIS
This Rear
.
3/8" TO EDGE
12"





4"

Trim the
rear wall
template
along
the dotted
mounting Wall Template
serves
plate and
outlet.
to position
to locate
the horizontal the bottom
1. Use
a level
exhaust
accurately. to check that
the template
2. Locate
is positioned
and
right side mark at least
 of the centerline.one stud on the
It is important
left or
screw mounted
to use at
least one
firmly in
of the microwave.
a stud to
wood
locations
support
Mark
for the suppliedtwo additional,
the weight
3. Drill holes
toggle bolts. evenly spaced
in the marked
a stud,
drill a 3/16"
locations.
that do
Where
hole for
not
wood screws. there is
toggle bolts.line up with
a stud,
drill 5/8" For holes

holes for
DO NOT
AT THIS
INSTALL
TIME.
THE MOUNTING
4. Remove
PLATE
5. Review the template
from the
the
rear wall.
installation Installation
situation. Instruction book
for your
line.

la
the dotted
Darle vuelta
a la hoja
versión
para consultar
en Español.


 
 

 







16-1/22″²




line.

Locate
and
mounting mark holes to
align with
plate.
IMPORTAN
holes in
the
LOCATE T:
AT LEAST
THE CENTERLI
ONE STUD
ON EITHER
NE.
MARK
THE
SIDE OF
SPACED LOCATION
FOR 2
TOGGLE
ADDITION
AREA.
BOLTS
AL, EVENLY
IN THE
MOUNTING
PLATE
Trim the
rear wall
template
Locate
and
mounting mark holes to
align with
plate.
IMPORTAN
holes in
the
LOCATE T:
AT LEAST
THE CENTERLI
ONE STUD
ON EITHER
NE.
MARK
THE
SIDE OF
SPACED LOCATION
FOR 2
TOGGLE
ADDITIONA
AREA.
BOLTS
L, EVENLY
IN THE
MOUNTING
PLATE


along
3/8" TO EDGE
12"
4"

 
 

Trim the
rear wall
template




along
the dotted
line.

la
the dotted



 
 










line.

Locate
and
mounting mark holes to
align with
plate.
IMPORTAN
holes in
the
LOCATE T:
AT LEAST
THE CENTERLI
ONE STUD
ON EITHER
NE.
MARK
THE
SIDE OF
SPACED LOCATION
FOR 2
TOGGLE
ADDITION
AREA.
BOLTS
AL, EVENLY
IN THE
MOUNTING
PLATE






C
Draw a vertical line on
the wall at the center of
the 30″ wide space.
Tape the Rear Wall
Template onto the wall
matching the centerline
and touching the
bottom of the cabinet.
At least 30″
C
Draw a vertical line on the wall at the center of the
30″ space.
Tape the Rear Wall Template onto the wall
matching the centerline and touching the bottom
cabinet frame.
Your cabinets may have decorative trim that
interferes with the microwave installation. Remove
the decorative trim to install the microwave properly
and to make it level.
Plate position-beneath recessed
bottom cabinet with front overhang
THE MICROWAVE MUST BE LEVEL.
Use a level to make sure the cabinet bottom is level.
If the cabinets have a front overhang only, with no
back or side frame, install the mounting plate down
the same distance as the front overhang depth. This
will keep the microwave level.
Draw a line on the
back wall equal to the
depth of the front
overhang.
NOTE:
IT IS VERY
READ
IMPORTA
AND FOLLOW
IN THE
NT TO
INSTALLA
THE DIRECTIO
BEFORE
TION INSTRUCT
PROCEED
NS
REAR
WALL
ING
IONS
TEMPLAT WITH THIS
This Rear
Wall
E.
mounting
Template
plate and
serves
outlet.
to position
to locate
the horizontal the bottom
1. Use
a level
exhaust
accurately. to check that
the template
2. Locate
and
is positioned
right side mark at least
 of the centerline.one stud on the
It is important
left or
screw mounted
to
of the microwave.
firmly in use at least one
a stud
locations
to support wood
Mark
the weight
3. Drill for the suppliedtwo additional,
holes in
evenly
toggle
the marked
spaced
bolts.
a stud,
drill a 3/16"
locations.
that do
hole
Where
not line
toggle
up with for wood screws. there is
bolts.
a stud,

drill 5/8" For holes
holes for
DO NOT
AT THIS
INSTALL
TIME.
THE MOUNTING
4. Remove
PLATE
5. Review the template
from the
the
installation Installation
rear
situation. Instruction wall.
book for
your
Darle vuelta
a la hoja
versión
para consultar
en Español.
along

 
 





Trim the
rear wall
template
along


the dotted
line.
la
Locate
and
mounting mark holes
to align
plate.
with holes
IMPORTA
in the
NT:
LOCATE
AT LEAST
THE CENTERL
ONE STUD
INE.
ON EITHER
MARK
THE LOCATION
SIDE OF
SPACED
FOR 2
TOGGLE
ADDITION
AREA.
BOLTS
AL, EVENLY
IN THE
MOUNTIN
G PLATE
Trim the
rear wall
template
3/8" TO EDGE
12"
4"
the dotted
300″3 to Cooktop



  

 





1 Measure the inside depth of the front overhang.



line.

Locate
and
mounting mark holes
to align
plate.
with holes
IMPORTA
in the
NT:
LOCATE
AT LEAST
THE CENTERL
ONE STUD
INE.
ON EITHER
MARK
THE LOCATION
SIDE OF
SPACED
FOR 2
TOGGLE
ADDITION
AREA.
BOLTS
AL, EVENLY
IN THE
MOUNTIN
G PLATE


NOTE:
IT IS VERY
READ
IMPORTANT
AND FOLLOW
IN THE
TO
INSTALLATION
THE DIRECTIONS
BEFORE
PROCEEDINGINSTRUCTIONS
REAR
WALL
TEMPLATE.WITH THIS
This Rear
Wall
mounting
Template
plate and
serves
outlet.
to position
to locate
the horizontal the bottom
1. Use
a level
exhaust
accurately. to check that
the template
2. Locate
and
is positioned
right side mark at least
 of the centerline.one stud on the
It is important
left or
screw mounted
to
of the microwave.
firmly in use at least one
a stud
locations
to support wood
Mark
the weight
3. Drill for the suppliedtwo additional,
holes in
evenly
toggle
the marked
spaced
bolts.
a stud,
drill a 3/16"
locations.
that do
hole
Where
not line
toggle
up with for wood screws. there is
bolts.
a stud,
drill 5/8" For holes

holes for
DO NOT
AT THIS
INSTALL
TIME.
THE MOUNTING
4. Remove
5. Review the template
PLATE
from the
the
installation Installation
rear
situation. Instruction wall.
book for
your


Darle vuelta
a la hoja
versión
para consultar
en Español.
CL
Trim the
rear wall
template
along
2 Draw a horizontal line on the back wall an equal
distance below the cabinet bottom as the inside
depth of the front overhang.
3/8" TO EDGE
12"
4"

 

 
Trim the
rear wall
template

along

the dotted
line.

la
Locate
and
mounting mark holes
to align
plate.
with holes
IMPORTANT:
in the
LOCATE
AT LEAST
THE CENTERLINE.
ONE STUD
MARK
ON EITHER
THE LOCATION
SIDE OF
SPACED
FOR 2
TOGGLE
ADDITIONAL,
AREA.
BOLTS
IN THE
EVENLY
MOUNTING
PLATE
the dotted


 










line.

Locate
and
mounting mark holes
to align
plate.
with holes
IMPORTANT:
in the
LOCATE
AT LEAST
THE CENTERLINE.
ONE STUD
MARK
ON EITHER
THE LOCATION
SIDE OF
SPACED
FOR 2
TOGGLE
ADDITIONAL,
AREA.
BOLTS
IN THE
EVENLY
MOUNTING
PLATE




C
3 For this type of installation with front overhang
only, align the mounting tabs with this horizontal
line, not touching the cabinet bottom as described
in Step D.
300″3 to Cooktop
EN-7
Installation Instructions
D. ALIGNING THE WALL PLATE
3/8" TO EDGE
12"
NOTE: IT IS VERY IMPORTANT TO
READ AND FOLLOW THE DIRECTIONS
IN THE INSTALLATION INSTRUCTIONS
BEFORE PROCEEDING WITH THIS
REAR WALL TEMPLATE.
This Rear Wall Template serves to position the bottom
mounting plate and to locate the horizontal exhaust
outlet.
1. Use a level to check that the template is positioned
accurately.
2. Locate and mark at least one stud on the left or
right side of the centerline.
016'It is important to use at least one wood
screw mounted firmly in a stud to support the weight
of the microwave. Mark two additional, evenly spaced
locations for the supplied toggle bolts.
3. Drill holes in the marked locations. Where there is
a stud, drill a 3/16" hole for wood screws. For holes
that do not line up with a stud, drill 5/8" holes for
toggle bolts.
016'DO NOT INSTALL THE MOUNTING PLATE
AT THIS TIME.
4. Remove the template from the rear wall.
5. Review the Installation Instruction book for your
installation situation.
4"
Trim the rear wall template along the dotted line.
(%76176(14*14+<106#.
1765+&'':*#756
%76*1.'6*417)*4'#49#..(14':*#756#&#2614
Darle vuelta a la hoja para consultar la
versión en Español.
%#76+10Ä+(':*#756#&#2614+5215+6+10'&1765+&'
4'%1//'0&'&&+/'05+10)4'#5'Ä.#&'0#+49+..
&+5%*#4)'+061*175'5647%674'
/+0+/7/9+&6*4'37+4'&
Locate and mark holes to align with holes in the
mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
Hole B
$
Horizontal Line
Locate and mark holes to align with holes in the
mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
4'#49#..6'/2.#6'
Centerline
notches
Draw a Vertical Line
on Wall from Center
of Top Cabinet
%
#
%
&
Area E
CL
CAUTION: Wear gloves
to avoid cutting fingers on
sharp edges.
1 Draw a vertical line on the wall at the center of the
30" wide space.
2 Draw a horizontal line on the wall at the bottom of
“Rear Wall Template”.
3 Find a wall stud in area "E" of mounting plate
Refer to section 1B. Finding the wall studs.
4 For attaching the mounting plate into stud drill
a 3/16" hole into wood stud. Drill a 5/8" hole for
toggle bolt in 1 other location (Hole A or Hole B)
NOTE: DO NOT MOUNT THE PLATE AT THIS
TIME.
EN-8
Hole A
Horizontal Line
Draw a horizontal line on wall at the
bottom of “Rear Wall Template”.
NOTE: Holes A and B are inside area E. If neither of
Holes A and B are not in a stud, find a stud somewhere
in area E and draw a circle to line up with the stud. It is
important to have at least one wood screw mounted
firmly in a stud to support the weight of the
microwave. Set the mounting plate aside.
Installation Instructions
2
INSTALLATION TYPES
This microwave oven is designed for adaptation to
the following three types of ventilation:
A. Outside Top Exhaust (Vertical Duct)
B. Outside Back Exhaust (Horizontal Duct)
C. Recirculating (Non-Vented Ductless)
A
(Choose A, B or C)
NOTE: This microwave is shipped assembled for
Recirculating. Select the type of ventilation required
for your installation and proceed to that section.
OUTSIDE TOP EXHAUST
(VERTICAL DUCT)
B
OUTSIDE BACK EXHAUST
(HORIZONTAL DUCT)
Adaptor Must Be
Moved to the Back for
Outside Back Exhaust
Adaptor in Place for
Outside Top Exhaust
See page 12
See page 16
C
RECIRCULATING
(NON-VENTED DUCTLESS)
Models are shipped for
recirculating exhaust.
Some models have a
disposable charcoal filter
installed to help remove
smoke and odors.
See page 20
NOTE: Read the next two pages only if you plan to vent your exhaust to the
outside. If you plan to recirculate the air back into the room, proceed to page 20.
EN-9
Installation Instructions
INSTALLATION INSTRUCTIONS FOR EXTERNAL EXHAUST DUCTING
NOTE: If you need to install ducts, note that the total
duct length of 31⁄4” x 10” (8.2 x 25.4 cm) rectangular or
5” (12.7 cm) diameter/ 6” (15.2 cm) diameter round duct
should not exceed 120 equivalent feet (36.5 m).
Outside ventilation requires an EXTERNAL EXHAUST
DUCT.Read the following carefully.
NOTE: It is important that venting be installed using
the most direct route and with as few elbows as possible.
This ensures clear venting of exhaust and helps prevent
blockages. Also, make sure dampers swing freely and
nothing is blocking the ducts.
Exhaust connection:
The exhaust adaptor has been designed to mate with
a standard 31⁄4” x 10” (8.2 x 25.4 cm) rectangular duct.
If a round duct is required, a rectangular-to-round
transition adaptor must be used. A 5""'" (12.7cm)/ 6" " (15.2cm)
diameter duct is acceptable to use.
Maximum duct length:
For satisfactory air movement, the total duct length of
31⁄4” x 10” (8.2 x 25.4 cm) rectangular or 5” (12.7 cm)
diameter/ 6 ”(15.2 cm) diameter round duct should not
exceed 120 equivalent feet (36.5 m).
Elbows, transitions, wall and roof caps,
etc., present additional resistance to airflow and are
equivalent to a section of straight duct which is longer
than their actual physical size. When calculating the total
duct length, add the equivalent lengths of all transitions
and adaptors plus the length of all straight duct sections.
The chart below shows you how to calculate total
equivalent ductwork length using the approximate feet
of equivalent length of some typical ducts.
EQUIVALENT
LENGTH
x
NUMBER
USED
=
Rectangular-to-Round
Transition Adaptor*
5 Ft. (1.5 m)
x
( )
=
Ft. or m
Wall Cap
40 Ft. (12.2 m)
x
( )
=
Ft. or m
90° Elbow
10 Ft. (3 m)
x
( )
=
Ft. or m
45° Elbow
5 Ft. (1.5 m)
x
( )
=
Ft. or m
90° Elbow
25 Ft. (7.6 m)
x
( )
=
Ft. or m
45° Elbow
5 Ft. (1.5 m)
x
( )
=
Ft. or m
Roof Cap
24 Ft. (7.3 m)
x
( )
=
Ft. or m
Straight Duct 6“ (15.2 cm)
Round or 31⁄4“ x 10“
(8.2 x 25.4 cm Rectangular)
1 Ft. (0.3 m)
x
( )
=
Ft. or m
=
Ft. or m
DUCT PIECES
Total Ductwork
* IMPORTANT: If a rectangular-to-round transition
adaptor is used, the bottom corners of the damper
will have to be cut to fit, using the tin snips, in order
to allow free movement of the damper.
EN-10
EQUIVALENT
LENGTH
Equivalent lengths of duct pieces are based on actual tests
and reflect requirements for good venting performance with
any vent hood.
Installation Instructions
EXTERNAL EXHAUST DUCTING
OUTSIDE TOP EXHAUST (EXAMPLE ONLY)
The following chart describes an example of one possible
ductwork installation.
EQUIVALENT
LENGTH
x
NUMBER
USED
=
EQUIVALENT
LENGTH
Roof Cap
24 Ft. (7.3 m)
x
(1)
=
24 Ft. (7.3 m)
12 Ft. (3.6 m) Straight Duct
(6”/15.2 cm Round)
12 Ft. (3.6 m)
x
(1)
=
12 Ft. (3.6 m)
Rectangular-to-Round
Transition Adaptor*
5 Ft. (1.5 m)
x
(1)
=
5 Ft. (1.5 m)
Total Length
=
41 Ft. (12.5 m)
DUCT PIECES
Equivalent lengths of duct pieces are based on actual tests and
reflect requirements for good venting performance with any vent hood.
* IMPORTANT: If a rectangular-to-round transition adaptor is used, the bottom corners of the damper
will have to be cut to fit, using the tin snips, in order to allow free movement of the damper.
OUTSIDE BACK EXHAUST (EXAMPLE ONLY)
The following chart describes an example of one possible
ductwork installation.
EQUIVALENT
LENGTH*
x
NUMBER
USED
=
EQUIVALENT
LENGTH
Wall Cap
40 Ft. (12.2 m)
x
(1)
=
40 Ft. (12.2 m)
3 Ft. Straight Duct
(31⁄4” x 10”/8.2 x 25.4 cm
Rectangular)
3 Ft. (0.9 m)
x
(1)
=
3 Ft. (0.9 m)
90° Elbow
10 Ft. (3 m)
x
(2)
=
20 Ft. (3 m)
Total Length
=
63 Ft. (19.2 m)
DUCT PIECES
Equivalent lengths of duct pieces are based on actual tests and
reflect requirements for good venting performance with any vent hood.
NOTE: For back exhaust, care should be taken to align exhaust with space between studs, or wall should be prepared
at the time it is constructed by leaving enough space between the wall studs to accommodate exhaust.
EN-11
Installation Instructions
A OUTSIDE TOP EXHAUST
(Vertical Duct)
INSTALLATION OVERVIEW
A1. Attach Mounting Plate to Wall
A2. Prepare Top Cabinet
A3. Adapting Microwave Blower for
Outside Top Exhaust
A4. Check Damper Operation
A5. Mount Microwave Oven
A6. Adjust Exhaust Adaptor
A7. Connect Ductwork
3/8" TO EDGE
along the dotted line.
Trim the rear wall template
12"
TO
NOTE: IT IS VERY IMPORTANT
THE DIRECTIONS
READ AND FOLLOW
INSTRUCTIONS
IN THE INSTALLATION
WITH THIS
BEFORE PROCEEDING
REAR WALL TEMPLATE.
serves to position the bottom
This Rear Wall Template
the horizontal exhaust
mounting plate and to locate
outlet.
that the template is positioned
1. Use a level to check
accurately.
one stud on the left or
2. Locate and mark at least
right side of the centerline.
least one wood
It is important to use at
a stud to support the weight
screw mounted firmly in
two additional, evenly spaced
of the microwave. Mark
toggle bolts.
locations for the supplied
locations. Where there is
3. Drill holes in the marked wood screws. For holes
for
a stud, drill a 3/16" hole
a stud, drill 5/8" holes for
that do not line up with
toggle bolts.
MOUNTING PLATE
DO NOT INSTALL THE
4"
AT THIS TIME.
from the rear wall.
4. Remove the template
Instruction book for your
5. Review the Installation
installation situation.
para consultar la
Darle vuelta a la hoja
versión en Español.
IMPORTANT NOTES:
• Make sure the screws for the
blower motor and blower plate
are securely tightened when
they are reinstalled. This will
help to prevent excessive
vibration.
• Make sure the motor wiring has
been properly routed and secured,
and that the wires are not pinched.
to align with holes in the
Locate and mark holes
mounting plate.
IMPORTANT:
OF
STUD ON EITHER SIDE
LOCATE AT LEAST ONE
THE CENTERLINE.
EVENLY
FOR 2 ADDITIONAL,
MARK THE LOCATION
IN THE MOUNTING PLATE
SPACED TOGGLE BOLTS
to align with holes in the
Locate and mark holes
mounting plate.
IMPORTANT:
OF
STUD ON EITHER SIDE
LOCATE AT LEAST ONE
AREA.
THE CENTERLINE.
EVENLY
FOR 2 ADDITIONAL,
MARK THE LOCATION
IN THE MOUNTING PLATE
SPACED TOGGLE BOLTS
along the dotted line.
Trim the rear wall template
AREA.
To use toggle bolts:
A1. ATTACH THE MOUNTING
PLATE TO THE WALL
Mounting
Plate
Spacing for Toggles
More Than Wall
Thickness
Toggle Wings
Toggle
Bolt
Wall
Bolt End
3 Place the mounting plate against the wall and
insert the toggle wings into the holes in the wall
to mount the plate.
NOTE: Before tightening toggle bolts and wood
screw, make sure the bottom of the mounting plate
touch the bottom of the cabinet when pushed
flush against the wall and that the plate is properly
centered under the cabinet.
CAUTION: Be careful to avoid pinching fingers
between the back of the mounting plate and the wall.
4 Tighten all bolts. Pull the plate away from the wall
to help tighten the bolts.
Attach the plate to the wall using toggle bolts.
At least one wood screw must be used to attach
the plate to a wall stud.
1 Remove the toggle wings from the bolts.
2 Insert the bolts into the mounting plate
through the holes designated to go into drywall
and reattach the toggle wings to 3⁄4″ (19 mm) onto
each bolt.
EN-12
Installation Instructions
A2. USE TOP CABINET TEMPLATE
FOR PREPARATION OF TOP
CABINET
2 Carefully pull out the blower unit. The wires
will extend far enough to allow you to adjust
the blower unit.
End B
You need to drill holes for the top support screws, a
hole large enough for the power cord to fit through,
and a cutout large enough for the exhaust adaptor.
End A
Back of
Microwave
3 Roll the blower unit 90° so that fan blade
openings are facing out the top of the
microwave.
Before Rotation
After Rotation
• Read the instructions on the TOP CABINET
TEMPLATE.
• Tape it underneath the top cabinet.
• Drill the holes, following the instructions on the
TOP CABINET TEMPLATE.
CAUTION: Wear safety goggles when drilling holes
in the cabinet bottom.
Back of
Microwave
Back of
Microwave
4 Place the blower unit back into the opening.
A3.
ADAPTING MICROWAVE
BLOWER FOR OUTSIDE
TOP EXHAUST
AFTER: Fan Blade
Openings Facing Top
1 Place the microwave in its upright position,
with the top of the unit facing up.
Blower Plate
Back of
Microwave
Back of
Microwave
CAUTION: Do not pull or stretch the blower
unit wiring. Make sure the wires are not
pinched, and that they are properly secured.
Blower Motor
Screw
Remove the screw that holds the blower plate
to the microwave. Remove and save the screw
holding the blower motor to the microwave.
EN-13
Installation Instructions
A3.
A5. MOUNT THE MICROWAVE
OVEN
ADAPTING MICROWAVE
BLOWER FOR OUTSIDE
TOP EXHAUST
5 Secure blower unit to microwave with the screw
removed in Step 1. Make sure the screw is tight.
6 Replace blower plate with the screw removed in
Step 1. Make sure the screw is tight.
FOR EASIER INSTALLATION AND PERSONAL
SAFETY, WE RECOMMEND THAT TWO PEOPLE
INSTALL THIS MICROWAVE OVEN.
IMPORTANT: Do not grip or use handle
during installation.
Back of
Microwave
NOTE: If your cabinet is metal, use the nylon
grommet around the power cord hole to prevent
cutting of the cord.
NOTE: We recommend using filler blocks if the
cabinet front hangs below the cabinet bottom shelf.
7 Attach the exhaust adaptor to the top of the
blower plate by sliding it into the guides of the
blower plate.
IMPORTANT: If filler blocks are
not used, case damage may occur from
overtightening screws.
Adaptor
Guide
NOTE: When mounting the
microwave oven, thread
power cord through hole in
bottom of top cabinet. Keep
it tight throughout Steps
1–3. Do not pinch cord or
lift oven by pulling cord.
Back of
Microwave
Locking Tab
Push in securely until it is in the locking tabs.
Take care to assure that the damper hinge is
installed so that the damper swings freely.
1 Lift microwave, tilt it
forward, and hook
slots at back bottom
edge onto four lower
tabs of mounting
plate.
A4. CHECK FOR PROPER
DAMPER OPERATION
Blower Plate
Exhaust Adaptor
Damper
2 Rotate front of oven
up against cabinet
bottom.
Back of
Microwave
3 Insert a self-aligning screw through top center
cabinet hole. Temporarily secure the oven by
turning the screw at least two full turns after the
threads have engaged. (It will be completely
tightened later.) Be sure to keep power cord
tight. Be careful not to pinch the cord, especially
when mounting flush to bottom of cabinet.
• Make sure tape securing damper is removed and
•
damper pivots easily before mounting microwave.
You will need to make adjustments to assure proper
alignment with your house exhaust duct after the
microwave is installed.
EN-14
Installation Instructions
A5. MOUNT THE MICROWAVE
OVEN (cont.)
A6. ADJUST THE EXHAUST
ADAPTOR
Open the top cabinet and adjust the exhaust adaptor
to connect to the house duct.
Cabinet Front
Cabinet Bottom Shelf
Filler Block
Blower Plate
Back of
Microwave
Damper
Equivalent
to Depth
of Cabinet
Recess
Self-Aligning Screw
For Front-to-Back or
Side-to-Side Adjustment,
Slide the Exhaust Adaptor
as Needed
Microwave Oven Top
4 Attach the microwave oven to the top cabinet.
5 Insert 2 self-aligning screws
through outer top cabinet
holes. Turn two full turns on
each screw.
A7. CONNECTING DUCTWORK
House Duct
6 Tighten center
screw completely.
7 Tighten the outer two screws to the top of the
microwave oven. (While tightening screws, hold
the microwave oven in place against the wall and
the top cabinet.)
1 Extend the house duct down to connect to
the exhaust adaptor.
2 Seal exhaust duct joints using furnance duct tape
for high temperature applications.
8 Install grease filters. See the Use a& nd Care
packed with the microwave.
EN-15
Installation Instructions
B OUTSIDE BACK EXHAUST
(Horizontal Duct)
INSTALLATION OVERVIEW
B1. Prepare Rear Wall
B2. Remove Blower Plate
B3. Attach Mounting Plate to Wall
B4. Prepare Top Cabinet
B5. Adjust Blower
B6. Mount the Microwave Oven
3/8" TO EDGE
along the dotted line.
Trim the rear wall template
12"
TO
NOTE: IT IS VERY IMPORTANT
THE DIRECTIONS
READ AND FOLLOW
INSTRUCTIONS
IN THE INSTALLATION
WITH THIS
BEFORE PROCEEDING
REAR WALL TEMPLATE.
serves to position the bottom
This Rear Wall Template
the horizontal exhaust
mounting plate and to locate
outlet.
that the template is positioned
1. Use a level to check
accurately.
one stud on the left or
2. Locate and mark at least
right side of the centerline.
least one wood
It is important to use at
a stud to support the weight
screw mounted firmly in
two additional, evenly spaced
of the microwave. Mark
toggle bolts.
locations for the supplied
locations. Where there is
3. Drill holes in the marked wood screws. For holes
for
a stud, drill a 3/16" hole
a stud, drill 5/8" holes for
that do not line up with
toggle bolts.
MOUNTING PLATE
DO NOT INSTALL THE
4"
AT THIS TIME.
from the rear wall.
4. Remove the template
Instruction book for your
5. Review the Installation
installation situation.
para consultar la
Darle vuelta a la hoja
versión en Español.
IMPORTANT NOTES:
• Make sure the screws for the
blower motor and blower plate
are securely tightened when
they are reinstalled. This will
help to prevent excessive
vibration.
• Make sure the motor wiring has
been properly routed and secured,
and that the wires are not pinched.
to align with holes in the
Locate and mark holes
mounting plate.
IMPORTANT:
OF
STUD ON EITHER SIDE
LOCATE AT LEAST ONE
THE CENTERLINE.
EVENLY
FOR 2 ADDITIONAL,
MARK THE LOCATION
IN THE MOUNTING PLATE
SPACED TOGGLE BOLTS
to align with holes in the
Locate and mark holes
mounting plate.
IMPORTANT:
OF
STUD ON EITHER SIDE
LOCATE AT LEAST ONE
AREA.
THE CENTERLINE.
EVENLY
FOR 2 ADDITIONAL,
MARK THE LOCATION
IN THE MOUNTING PLATE
SPACED TOGGLE BOLTS
along the dotted line.
Trim the rear wall template
AREA.
B2. REMOVE BLOWER PLATE
B1. PREPARING THE REAR WALL
FOR OUTSIDE BACK EXHAUST
Remove and save the screw that holds the blower
plate to the microwave. Lift off the blower plate.
You need to cut an opening in the rear wall for
outside exhaust.
Blower Plate
Back of
Microwave
NOTE:
IT IS VERY
READ
IMPORT
AND FOLLOW
IN THE
ANT TO
INSTAL
THE DIRECT
BEFORE
LATION
IONS
PROCE
INSTRU
REAR
EDING
CTIONS
WALL
WITH
TEMPLA
This Rear
THIS
TE.
Wall
mounting
Template
plate and
serves
outlet.
to position
to locate
the horizontal the bottom
1. Use
a level
exhaust
accurately. to check that
the template
2. Locate
and
is positioned
right side mark at least
 of the centerline.one stud on the
It is important
left or
screw mounted
to
of the microwave.
firmly in use at least one
a stud
locations
to support wood
Mark
the weight
3. Drill for the suppliedtwo additional,
holes in
evenly
toggle
the marked
spaced
bolts.
a stud,
drill a 3/16"
locations.
that do
hole
Where
not line
toggle
up with for wood screws. there is
a stud,
bolts.
drill 5/8" For holes
DO NOT
holes for
AT THIS
INSTALL
TIME.
THE MOUNTING
4. Remove
PLATE
5. Review the template
from the
the
installation Installation
rear
situation. Instruction wall.
book for
your
Darle vuelta
a la hoja
versión
para consultar
en Español.

 




Trim the
rear wall
templat

e along



the dotted

line.


la
Locate
and mark
mountin
holes to
g plate.
align with
IMPORT
holes in
ANT:
the
LOCATE
AT LEAST
THE CENTER
ONE STUD
LINE.
ON EITHER
MARK
THE LOCATI
SIDE OF
SPACED
ON FOR
TOGGL
AREA.
E BOLTS 2 ADDITIO
NAL, EVENLY
IN THE
MOUNT
ING PLATE


  







the dotted




Trim the
rear wall
templat
e along
3/8" TO EDGE
12"
4"

line.

Locate
and mark
mountin
holes to
g plate.
align with
IMPORT
holes in
ANT:
the
LOCATE
AT LEAST
THE CENTER
ONE STUD
LINE.
ON EITHER
MARK
THE LOCATI
SIDE OF
SPACED
ON FOR
TOGGL
AREA.
E BOLTS 2 ADDITIO
NAL, EVENLY
IN THE
MOUNT
ING PLATE




• Read the instructions on the REAR
WALL TEMPLATE.
• Tape it to the rear wall.
• Cut the opening, following the instructions of the
REAR WALL TEMPLATE.
EN-16
Installation Instructions
B3. ATTACH THE MOUNTING
PLATE TO THE WALL
B4. USE TOP CABINET TEMPLATE
FOR PREPARATION OF TOP
CABINET
You need to drill holes for the top support screws and
a hole large enough for the power cord to fit through.
Attach the plate to the wall using toggle bolts.
At least one wood screw must be used to attach
the plate to a wall stud.
1 Remove the toggle wings from the bolts.
2 Insert the bolts into the mounting plate through
the holes designated to go into drywall and reattach
the toggle wings to 3⁄4″ (19 mm) onto each bolt.
•
•
To use toggle bolts:
CAUTION: Wear safety goggles when drilling holes
in the cabinet bottom.
Mounting
Plate
• Read the instructions on the TOP CABINET
Spacing for Toggles More
Than Wall Thickness
Toggle Wings
Toggle
Bolt
Wall
TEMPLATE.
Tape it underneath the top cabinet.
Drill the holes, following the instructions on the
TOP CABINET TEMPLATE.
B5. ADAPTING MICROWAVE
BLOWER FOR OUTSIDE
BACK EXHAUST
1 Remove and save screw that holds blower motor
to microwave.
Bolt End
Blower Motor
3 Place the mounting plate against the wall and
insert the toggle wings into the holes in the wall
to mount the plate.
NOTE: Before tightening toggle bolts and wood
screw, make sure the bottom of the mounting plate
touch the bottom of the cabinet when pushed flush
against the wall and that the plate is properly
centered under the cabinet.
CAUTION: Be careful to avoid pinching fingers
between the back of the mounting plate and the wall.
4 Tighten all bolts. Pull the plate away from the wall
to help tighten the bolts.
Back of
Microwave
Blower Motor
Screw
2 Carefully pull out the blower unit. The wires
will extend far enough to allow you to adjust
the blower unit.
Before: Fan Blade
Openings Facing
Forward
End A
EN-17
End B
Installation Instructions
7 Place the blower unit back into the opening.
B5. ADAPTING MICROWAVE
BLOWER FOR OUTSIDE
BACK EXHAUST (cont.)
AFTER: Fan Blade
Openings Facing Back
End A
3 Roll the blower unit 90°
Before Rotation
After Rotation
End B
CAUTION: Do not pull or stretch the blower
unit wiring. Make sure the wires are not
pinched, and that they are properly secured.
Back of
Microwave
Back of
Microwave
NOTE: The blower unit exhaust
openings should match exhaust
openings on rear of microwave oven.
4 Rotate blower unit counterclockwise 180°.
Before Rotation
After Rotation
8
Secure the blower unit to the microwave with
the original screw.
Blower Plate
Back of
Microwave
Back of
Microwave
Back of
Microwave
Blower Motor
Screw
5 Gently remove the wires from the grooves.
Reroute the wires through grooves on other side
of the blower unit.
Before Rerouting
After Rerouting
9 Replace the blower plate in the same position
as before with the screw. Make sure the screw
is tight.
10 Attach the exhaust adaptor to the rear of the
oven by sliding it into the guides at the top
center of the back of the oven.
Wires Routed Through Right Side
Wires Routed Through Left Side
Adaptor
6 Roll the blower unit 90° so that fan blade
openings are facing out the back of the
microwave.
Before Rolling
Back of
Microwave
After Rolling
Guide
Guide
Back of
Microwave
Locking Tabs
Push in securely until it is in the lower locking
tabs. Take care to assure that the damper hinge
is installed so that it is at the top and that the
damper swings freely.
Back of
Microwave
EN-18
Installation Instructions
Cabinet Front
B6. MOUNT THE MICROWAVE
OVEN
Cabinet Bottom Shelf
Filler Block
Equivalent
to Depth
of Cabinet
Recess
Self-Aligning Screw
FOR EASIER INSTALLATION AND PERSONAL
SAFETY, WE RECOMMEND THAT TWO PEOPLE
INSTALL THIS MICROWAVE OVEN.
Microwave Oven Top
4 Attach the microwave oven to the top cabinet.
IMPORTANT: Do not grip or use handle
during installation.
5 Insert 2 self-aligning screws
through outer top cabinet
holes. Turn two full turns on
each screw.
NOTE: If your cabinet is metal, use the nylon
grommet around the power cord hole to prevent
cutting of the cord.
NOTE: We recommend using filler blocks if the
cabinet front hangs below the cabinet bottom shelf.
IMPORTANT: If filler blocks are not
used, case damage may occur from
overtightening screws.
NOTE: When mounting the
microwave oven, thread
power cord through hole in
bottom of top cabinet. Keep
it tight throughout Steps
1–3. Do not pinch cord or
lift oven by pulling cord.
6 Tighten center
screw completely.
1 Lift microwave, tilt it
forward, and hook
slots at back bottom
edge onto four lower
tabs of mounting
plate.
7 Tighten the outer two screws to the top of the
microwave oven. (While tightening screws, hold
the microwave oven in place against the wall and
the top cabinet.)
8 Install grease filters. See the Use a& nd Care
packed with the microwave.
2 Rotate front of oven
up against cabinet
bottom.
3 Insert a self-aligning screw through top center
cabinet hole. Temporarily secure the oven by
turning the screw at least two full turns after the
threads have engaged. (It will be completely
tightened later.) Be sure to keep power cord
tight. Be careful not to pinch the cord, especially
when mounting flush to bottom of cabinet.
EN-19
Installation Instructions
C RECIRCULATING
(Non-Vented Ductless)
INSTALLATION OVERVIEW
C1. Attach Mounting Plate to Wall
C2. Prepare Top Cabinet
C3. Check Blower Plate
C4. Mount the Microwave Oven
C5. Install or change Charcoal Filter
3/8" TO EDGE
along the dotted line.
Trim the rear wall template
12"
TO
NOTE: IT IS VERY IMPORTANT
THE DIRECTIONS
READ AND FOLLOW
INSTRUCTIONS
IN THE INSTALLATION
WITH THIS
BEFORE PROCEEDING
REAR WALL TEMPLATE.
serves to position the bottom
This Rear Wall Template
the horizontal exhaust
mounting plate and to locate
outlet.
that the template is positioned
1. Use a level to check
accurately.
one stud on the left or
2. Locate and mark at least
right side of the centerline.
least one wood
It is important to use at
a stud to support the weight
screw mounted firmly in
two additional, evenly spaced
of the microwave. Mark
toggle bolts.
locations for the supplied
locations. Where there is
3. Drill holes in the marked wood screws. For holes
for
a stud, drill a 3/16" hole
a stud, drill 5/8" holes for
that do not line up with
toggle bolts.
MOUNTING PLATE
DO NOT INSTALL THE
4"
AT THIS TIME.
from the rear wall.
4. Remove the template
Instruction book for your
5. Review the Installation
installation situation.
para consultar la
Darle vuelta a la hoja
versión en Español.
to align with holes in the
Locate and mark holes
mounting plate.
IMPORTANT:
OF
STUD ON EITHER SIDE
LOCATE AT LEAST ONE
THE CENTERLINE.
EVENLY
FOR 2 ADDITIONAL,
MARK THE LOCATION
IN THE MOUNTING PLATE
SPACED TOGGLE BOLTS
AREA.
along the dotted line.
Trim the rear wall template
IMPORTANT NOTES:
• Make sure the screws for the blower motor and blower
plate are securely tightened when they are reinstalled.
This will help to prevent excessive vibration.
• Make sure the motor wiring has been properly routed
and secured, and that the wires are not pinched.
C1. ATTACH THE MOUNTING
PLATE TO THE WALL
to align with holes in the
Locate and mark holes
mounting plate.
IMPORTANT:
OF
STUD ON EITHER SIDE
LOCATE AT LEAST ONE
THE CENTERLINE.
EVENLY
FOR 2 ADDITIONAL,
MARK THE LOCATION
IN THE MOUNTING PLATE
SPACED TOGGLE BOLTS
AREA.
1 Remove the toggle wings from the bolts.
2 Insert the bolts into the mounting plate through
the holes designated to go into drywall and
reattach the toggle wings to 3⁄4″ (19 mm) onto
each bolt.
To use toggle bolts:
Mounting
Plate
Attach the plate to the wall using toggle bolts.
At least one wood screw must be used to attach
the plate to a wall stud.
Wall
Bolt End
NOTE: If the cabinet depth including the cabinet doors
is more than 13"'" ' then the unit must be spaced
out from wall using adequate materials supporting
150 Ibs to allow proper top vent air exhaust.
Cabinet
Spacing for Toggles
More Than Wall
Thickness
Toggle Wings
Toggle
Bolt
3 Place the mounting plate against the wall and
insert the toggle wings into the holes in the wall
to mount the plate.
NOTE: Before tightening toggle bolts and wood
screw, make sure the bottom of the mounting plate
touch the bottom of the cabinet when pushed flush
against the wall and that the plate is properly
centered under the cabinet.
CAUTION: Be careful to avoid pinching fingers
between the back of the mounting plate and the wall.
4 Tighten all bolts. Pull the plate away from the wall
to help tighten the bolts.
Cabinet
EN-20
Installation Instructions
C2. USE TOP CABINET TEMPLATE
FOR PREPARATION OF TOP
CABINET
C4. MOUNT THE MICROWAVE OVEN
You need to drill holes for the top support screws and
a hole large enough for the power cord to fit through.
FOR EASIER INSTALLATION AND PERSONAL
SAFETY, WE RECOMMEND THAT TWO PEOPLE
INSTALL THIS MICROWAVE OVEN.
IMPORTANT: Do not grip or use handle
during installation.
•
Read the instructions on the TOP CABINET
TEMPLATE.
• Tape it underneath the top cabinet.
NOTE: Adjust top template accordingly if the microwave
is being spaced out from the wall due to cabinet depth
(including cabinet doors) of more than 13"'" '.
• Drill the holes, following the instructions on the
TOP CABINET TEMPLATE.
CAUTION: Wear safety goggles when drilling holes
in the cabinet bottom.
C3. CHECK BLOWER PLATE
NOTE: If your cabinet is metal, use the nylon
grommet around the power cord hole to prevent
cutting of the cord.
NOTE: We recommend using filler blocks if the
cabinet front hangs below the cabinet bottom shelf.
IMPORTANT: If filler blocks are not used,
case damage may occur from overtightening
screws.
NOTE: When mounting the
microwave oven, thread
power cord through hole in
bottom of top cabinet. Keep
it tight throughout Steps
1–3. Do not pinch cord or
lift oven by pulling cord.
1 Lift microwave, tilt
it forward, and hook
slots at back bottom
edge onto four lower
tabs of mounting
plate.
Blower Plate
•
•
Place the microwave in its upright position, with the
top of the unit facing up.
Check to see that the blower plate is correctly
installed on the unit.
2 Rotate front of oven
up against cabinet
bottom.
3 Insert a self-aligning screw through top center
cabinet hole. Temporarily secure the oven by
turning the screw at least two full turns after the
threads have engaged. (It will be completely
tightened later.) Be sure to keep power cord
tight. Be careful not to pinch the cord, especially
when mounting flush to bottom of cabinet.
Cabinet Front
Cabinet Bottom Shelf
Filler Block
Equivalent to Depth
of Cabinet Recess
Self-Aligning Screw
Microwave Oven Top
4 Attach the microwave oven to the top cabinet.
EN-21
Installation Instructions
C4. MOUNT THE MICROWAVE
OVEN (cont.)
2 Open the microwave door and remove the two
vent mounting screws l; ocated on top of the
microwave using a #1 Phillips screwdriver.
5 Insert 2 self-aligning screws
through outer top cabinet
holes. Turn two full turns on
each screw.
3 Slide the vent left and tip forward. Lift out to
remove.
4 Lift the bottom of the charcoal filter. Slide the filter
straight out.
6 Tighten center
screw completely.
7 Tighten the outer two screws to the top of the
microwave oven. (While tightening screws, hold
the microwave oven in place against the wall and
the top cabinet.)
5 Slide a new charcoal filter into place. The filter
should rest at below shown.
8 Install grease filters. See the Use a& nd Care
packed with the microwave.
C5. INSTALLING OR CHANGE
THE CHARCOAL FILTER
(Some Models)
6 Reinstall the vent by sliding the bottom of the
vent into place. Push the vent top into position
and slide right into place. Replace the two vent
mounting screws located on top of the microwave
using a #1 Phillips screwdriver.
NOTE: The charcoal filter is factory installed in some
models. Refer to the Use and Care to see if yours is
factory installed and for replacement information.
Follow these steps to replace or install a charcoal filter.
1 Unplug microwave oven or disconnect power.
7 Close the microwave door. Plug in microwave
oven or reconnect power.
EN-22
Installation Instructions
BEFORE YOU USE YOUR MICROWAVE
1.
Make sure the microwave oven has been
installed according to instructions.
Replace house fuse or turn breaker back on.
5.
N
LATIO S
L
A
T
INS UCTION
R
INST
6.
2.
Read the USE & CARE Manual.
Remove all packing material from the
microwave oven.
RE
&|+&= CA
USE NUAL
MA
3.
+
Install turntable ring and glas s tray in cavity.
7.
KEEP INSTALLATION INSTRUCTIONS
FOR THE LOCAL INSPECTOR’S
USE.
ION
LLAT NS
A
T
S
IN
IO
RUCT
INST
4.
Plug power cord into a dedicated 15- to 20-amp
electrical outlet.
8.
FILL OUT PRODUCT REGISTRATION CARD
AN SEND IN.
UCT
PROD ATION
STR
REGI ARD
C
Ensure proper
ground exists
before use
D
G
G
D
EN-23
D
D
3/8" TO EDGE
12"
NOTE: IT IS VERY IMPORTANT TO
READ AND FOLLOW THE DIRECTIONS
IN THE INSTALLATION INSTRUCTIONS
BEFORE PROCEEDING WITH THIS
REAR WALL TEMPLATE.
This Rear Wall Template serves to position the bottom
mounting plate and to locate the horizontal exhaust
outlet.
1. Use a level to check that the template is positioned
accurately.
2. Locate and mark at least one stud on the left or
right side of the centerline.
It is important to use at least one wood
screw mounted firmly in a stud to support the weight
of the microwave. Mark two additional, evenly spaced
locations for the supplied toggle bolts.
3. Drill holes in the marked locations. Where there is
a stud, drill a 3/16" hole for wood screws. For holes
that do not line up with a stud, drill 5/8" holes for
toggle bolts.
DO NOT INSTALL THE MOUNTING PLATE
AT THIS TIME.
4. Remove the template from the rear wall.
5. Review the Installation Instruction book for your
installation situation.
Trim the rear wall template along the dotted line.


4"

Darle vuelta a la hoja para consultar la
versión en Español.




Locate and mark holes to align with holes in the
mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.


Locate and mark holes to align with holes in the
mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
Trim the rear wall template along the dotted line.
Part No.:316902476




13-3/8"
13-3/8"
8"
3/
8-1/4"
8"
3/8"
3/
3/8"
8"
3/
3/8"
3/8"
9-27/32"
2"
2"
2"
6-1/4"
4-1/4"
4-1/2"
1/2"
12-1/2"
Part No.:316902475
PN: 261800314115
EN-24
Printed in China
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising