Sub-Zero | IW-30R-RH | Design Guide | Sub-Zero IW-30R-RH Design Guide

Sub-Zero IW-30R-RH Design Guide
SUB-ZERO DESIGN GUIDE
REVISED 7 / 2016
TA B L E O F C O N T E N T S
3
B U I L T- I N R E F R I G E R A T I O N
40
P R O 4 8 R E F R I G E R AT I O N
46
I N T E G R AT E D R E F R I G E R AT I O N
56
WINE STORAGE
88
U N D E R C O U N T E R R E F R I G E R AT I O N
98
SUB-ZERO WARRANTIES
Features and specifications are subject to change at any
time without notice. Visit subzero.com/specs for the most
up-to-date information.
Throughout this guide, dimensions may vary by ± 1/8" (3).
Dimensions in parentheses are millimeters unless otherwise
specified.
B U I L T- I N
B UILT-IN R EF R IGE RATION
Built-In Refrigeration
B UILT-IN MO DELS
I N T E G R AT E D
PRO 48
For the built-in line, Sub-Zero designers and engineers took
a fresh look at everything, inside and out. Exterior refinements include redesigned grilles and lower-profile hinges.
Inside, new technology in food preservation makes the builtin line nothing short of revolutionary.
BI-36R
BI-42UFD(ID)
BI-36F
BI-36S
UNDERCOUNTER
WINE
BI-36UFD(ID)
BI-36RG
4
|
Sub-Zero Customer Care 800.222.7820
BI-30U
BI-42S(ID)
BI-30UG
BI-42SD
BI-36U(ID)
BI-48S(ID)
BI-36UG
BI-48S
B UILT-IN R EF R IGE RATION
B U I L T- I N
Specifications
INTERIOR CAPACITY— CU FT
(L )
A L L R E F R I G E R AT O R | ALL FREE Z E R
BI-36R
BI-36RG
BI-36F
OV E R - A N D - U N D E R
SI D E - B Y- S I D E
22.7 (643)
REFR
FRZR
13.2 (374)
13.1 (371)
16.4 (464)
16.3 (462)
15.7 (445)
18.3 (518)
4.2 (119)
4.2 (119)
5.3 (150)
5.3 (150)
5.3 (150)
6.4 (181)
REFR
FRZR
12.4 (351)
16.3 (462)
15.8 (447)
16.0 (453)
19.1 (541)
18.6 (527)
18.8 (532)
8.2 (232)
8.0 (227)
7.9 (224)
7.9 (224)
9.8 (278)
9.6 (272)
9.6 (272)
I N T E G R AT E D
BI-36S
BI-42S
BI-42SID
BI-42SD
BI-48S
BI-48SID
BI-48SD
FRZR
PRO 48
BI-30U
BI-30UG
BI-36U(ID)
BI-36UG
BI-36UFD(ID)
BI-42UFD(ID)
REFR
23.5 (665)
23.4 (663)
WINE
|
5
UNDERCOUNTER
subzero.com/specs
B U I L T- I N
B UILT-IN R EF R IGE RATION
PRO 48
Built-In Design Options
F R AMED
O VER LAY
For the classic Sub-Zero look, choose framed custom
door panels that contrast with the stainless steel full-length
handles and louvered grille (shown). The framed application is an overlay model with framed design features. Panel,
grille and handle options are available.
Custom overlay door panels can be combined with unique
handle hardware for design flexibility. Shown with pro
handle option to complement Wolf ranges. Customize with
panel, grille and handle options.
Panels | Custom panels, stainless steel or white enamel.
Grille | Classic louvered grille insert or solid custom panel
for 84" (standard), 83" or 88" overall unit height. Dual wide
grille for dual installations.
Panels | Custom panels or stainless steel.
Grille | Solid custom panel or pro louvered grille for 84"
(standard), 83" or 88" overall unit height. Dual wide grille for
dual installations.
Handles | Custom, tubular or pro handles.
UNDERCOUNTER
WINE
I N T E G R AT E D
Handles | Full-length standard or extended.
Framed.
6
|
Sub-Zero Customer Care 800.222.7820
Overlay.
B UILT-IN R EF R IGE RATION
B U I L T- I N
Built-In Design Options
F LUS H INS ET
S TA I N LES S S TEEL
The flush inset design option allows for flush door and grille
panels and custom handle hardware. Shown with tubular
handle option to match Wolf built-in ovens. The flush inset
application is an overlay model with flush inset panels. Customize with panel, grille and handle options.
For a professional look, classic stainless steel models
require no customization. To complement the look of Wolf
ranges, choose the pro handle option (shown). Grille and
handle options are available.
Grille | Solid custom panel or pro louvered grille for 84"
(standard), 83" or 88" overall unit height. Dual wide grille for
dual installations.
Grille | Pro louvered grille for 84" (standard), 83" or 88"
overall unit height. Dual wide grille for dual installations.
PRO 48
Panels | Custom panels or stainless steel.
Handles | Tubular or pro handles.
Handles | Custom, tubular or pro handles.
I N T E G R AT E D
WINE
Stainless steel.
subzero.com/specs
|
7
UNDERCOUNTER
Flush inset.
B U I L T- I N
B UILT-IN R EF R IGE RATION
Overall Dimensions
A L L R EF R IG ER ATOR | AL L FRE E Z E R
26 3/16" (665)
PRO 48
36" (914)
84"
(2134)
73 3/4"
I N T E G R AT E D
(1873)
HEIGHT DIMENSIONS ± 1/2" (13)
4" (102)
23 7/8"
(606)
14 1/8"
(359)
37 1/4"
WINE
(946)
2 3/8" (60)
UNDERCOUNTER
Model BI-36R, BI-36RG, BI-36F.
8
|
Sub-Zero Customer Care 800.222.7820
23 7/8" (606)
Overall dimensions are based on stainless steel models.
For flush inset applications, add 1/2" (13) to door clearance
dimensions.
B UILT-IN R EF R IGE RATION
B U I L T- I N
Overall Dimensions
O VER -AND-UND E R
26 3/16" (665)
30" (762)
26 3/16" (665)
36" (914)
(2134)
50 3/4"
50 3/4"
(1289)
(1289)
23"
23"
4" (102)
HEIGHT DIMENSIONS ± 1/2" (13)
23 7/8" (606)
(606)
(606)
14 1/8"
12 1/8"
(308)
(600)
23 7/8" (606)
23 7/8"
23 7/8"
23 5/8"
4" (102)
I N T E G R AT E D
(584)
(584)
HEIGHT DIMENSIONS ± 1/2" (13)
PRO 48
84"
84"
(2134)
(359)
311/4"
(796)
23 5/8"
(600)
37 1/4"
(946)
WINE
2 3/8" (60)
2 3/8" (60)
Model BI-30U, BI-30UG.
Model BI-36U(ID), BI-36UG.
|
9
UNDERCOUNTER
subzero.com/specs
B U I L T- I N
B UILT-IN R EF R IGE RATION
Overall Dimensions
O VER -AND-UND E R
26 3/16" (665)
PRO 48
36" (914)
26 3/16" (665)
42" (1067)
84"
84"
(2134)
(2134)
50 3/4"
50 3/4"
(1289)
(1289)
23"
23"
I N T E G R AT E D
(584)
HEIGHT DIMENSIONS ± 1/2" (13)
(584)
4" (102)
HEIGHT DIMENSIONS ± 1/2" (13)
23 7/8" (606)
23 7/8"
4" (102)
23 7/8"
(606)
(606)
8"
9"
(203)
(229)
23 5/8"
191/2" 23 5/8"
(495)
(600)
(600)
221/4"
WINE
(565)
2 3/8" (60)
UNDERCOUNTER
Model BI-36UFD(ID).
10
|
Sub-Zero Customer Care 800.222.7820
2 3/8" (60)
Model BI-42UFD(ID).
23 7/8" (606)
B UILT-IN R EF R IGE RATION
B U I L T- I N
Overall Dimensions
S I DE-B Y-S IDE
26 3/16" (665)
36" (914)
(2134)
73 3/4"
73 3/4"
(1873)
(1873)
HEIGHT DIMENSIONS ± 1/2" (13)
23 7/8" (606)
4" (102)
23 7/8" (606)
23 7/8"
(606)
(606)
7 1/2"
(191)
8 3/4"
(222)
I N T E G R AT E D
4" (102)
23 7/8"
7 1/4"
(184)
PRO 48
84"
84"
(2134)
HEIGHT DIMENSIONS ± 1/2" (13)
26 3/16" (665)
42" (1067)
10 3/8"
(264)
26 1/4"
221/4"
(668)
(565)
WINE
2 3/8" (60)
2 3/8" (60)
Model BI-36S.
Model BI-42S(ID), BI-42SD.
|
11
UNDERCOUNTER
subzero.com/specs
B U I L T- I N
B UILT-IN R EF R IGE RATION
Overall Dimensions
S I DE-B Y-S IDE
26 3/16" (665)
PRO 48
48" (1219)
84"
(2134)
73 3/4"
I N T E G R AT E D
(1873)
HEIGHT DIMENSIONS ± 1/2" (13)
4" (102)
23 7/8"
(606)
8 3/8"
(213)
11 5/8"
(295)
30"
WINE
(762)
2 3/8" (60)
UNDERCOUNTER
Model BI-48S(ID), BI-48SD.
12
|
Sub-Zero Customer Care 800.222.7820
23 7/8" (606)
B UILT-IN R EF R IGE RATION
B U I L T- I N
Specifications
SHIPPING WEIGHT
A L L R E F R I G E R AT O R | ALL FREE Z E R
BI-36R
BI-36RG
BI-36F
OV E R - A N D - U N D E R
SI D E - B Y- S I D E
L B (KG )
538 (244)
582 (264)
608 (276)
608 (276)
630 (286)
656 (298)
656 (298)
I N T E G R AT E D
BI-36S
BI-42S
BI-42SID
BI-42SD
BI-48S
BI-48SID
BI-48SD
L B (KG )
462 (210)
476 (216)
515 (234)
529 (240)
529 (240)
582 (264)
PRO 48
BI-30U
BI-30UG
BI-36U(ID)
BI-36UG
BI-36UFD(ID)
BI-42UFD(ID)
L B (KG )
420 (191)
430 (195)
406 (184)
Shipping weights are based on stainless steel models.
WINE
|
13
UNDERCOUNTER
subzero.com/specs
B U I L T- I N
B UILT-IN R EF R IGE RATION
Opening Dimensions
S TANDAR D INS TAL L ATION
PRO 48
24" (610)
OPENING
DEPTH
I N T E G R AT E D
TOP VIEW
83 3/4"
(2127)
OPENING
HEIGHT
WINE
SIDE VIEW
W
OPENING WIDTH
FRONT VIEW
NOTE: Shaded line represents profile of unit.
UNDERCOUNTER
OPENING WIDTH
W
30" Model
29 1/2" (749)
36" Model
35 1/2" (902)
42" Model
41 1/2" (1054)
48" Model
47 1/2"
14
|
Sub-Zero Customer Care 800.222.7820
(1206)
If an 83" (2108) grille height is specified, the opening height
must be decreased by 7/8" (22). If an 88" (2235) grille height is
specified, the opening height must be increased by 4" (102).
If two units are installed side by side, refer to page 16 for
dual standard installations.
B UILT-IN R EF R IGE RATION
B U I L T- I N
Opening Dimensions
F LUS H INS ET INSTAL L ATION
26 3/16"
(665)
FLUSH
INSET
DEPTH
2 3/16"
(56)
PRO 48
FINISHED
CLEATS*
TOP VIEW
11/4"
1/4"
(6)
(32)
I N T E G R AT E D
84"
(2134)
FLUSH
INSET
HEIGHT
W
FLUSH INSET WIDTH
11/4"
(32)
4" (102)
3"
(76)*
TYPICAL
SIDE VIEW
2 3/16"
(56)
FRONT VIEW
WINE
*3" (76) typical depth. Shaded areas will be visible and should be finished to match cabinetry.
NOTE: Shaded line represents profile of unit with 3/4" (19) panel.
FLUSH INSET WIDTH
W
30" Model
32" (813)
36" Model
38" (965)
42" Model
44" (1118)
48" Model
50" (1270)
Dimensions assume a 3/4" (19) panel thickness.
If an 83" (2108) grille height is specified, the flush inset
height must be decreased by 7/8" (22). If an 88" (2235) grille
height is specified, the flush inset height must be increased
by 4" (102).
subzero.com/specs
|
15
UNDERCOUNTER
If two units are installed side by side, refer to page 17 for
dual flush inset installations.
B U I L T- I N
B UILT-IN R EF R IGE RATION
Opening Dimensions
D U AL S TANDARD INSTAL L ATION
PRO 48
24" (610)
OPENING
DEPTH
I N T E G R AT E D
TOP VIEW
(2127)
OPENING
HEIGHT
WINE
SIDE VIEW
OPENING WIDTH
FRONT VIEW
NOTE: Shaded line represents profile of unit.
DUAL OPENING WIDTH
UNDERCOUNTER
W
83 3/4"
W
Two 30" Models
59 3/4" (1518)
30" and 36" Models
65 3/4" (1670)
Two 36" Models
71 3/4" (1822)
16
|
Sub-Zero Customer Care 800.222.7820
A dual installation kit will be required for this installation.
B UILT-IN R EF R IGE RATION
B U I L T- I N
Opening Dimensions
D U AL F LUS H IN SE T INSTAL L ATION
26 3/16"
(665)
FLUSH
INSET
DEPTH
2 3/16"
(56)
PRO 48
FINISHED
CLEATS*
TOP VIEW
11/4"
1/4"
(6)
(32)
I N T E G R AT E D
W
84"
(2134)
FLUSH
INSET
HEIGHT
FLUSH INSET WIDTH
11/4"
(32)
4" (102)
3"
(76)*
TYPICAL
SIDE VIEW
2 3/16"
(56)
FRONT VIEW
WINE
*3" (76) typical depth. Shaded areas will be visible and should be finished to match cabinetry.
NOTE: Shaded line represents profile of unit with 3/4" (19) panel.
DUAL FLUSH INSET WIDTH
W
Two 30" Models
62 1/4" (1581)
30" and 36" Models
68 1/4" (1734)
Two 36" Models
74 1/4" (1886)
Dimensions assume a 3/4" (19) panel thickness. A dual installation kit will be required for this installation.
|
17
UNDERCOUNTER
subzero.com/specs
B U I L T- I N
B UILT-IN R EF R IGE RATION
Electrical
Plumbing
The electrical supply should be located within the shaded
area shown in the illustration below. A separate circuit, servicing only this appliance is required. A ground fault circuit
interrupter (GFCI) is not recommended and may cause
interruption of operation.
The water supply line should be located within the shaded
area shown in the illustration below. The water supply line
should be connected to the house supply with an easily
accessible shut-off valve. Do not use self‑piercing valves.
The water supply line must not interfere with installation of
the anti-tip brackets.
PRO 48
Installation must comply with all applicable electrical codes.
ELECTRICAL REQUIREMENTS
Electrical Supply
115 VAC, 60 Hz
Service
15 amp
Receptacle
3-prong grounding-type
A reverse osmosis system can be used provided there is
constant water pressure of 35–120 psi (2.4–8.3 bar) supplied
to the unit at all times. A copper line is not recommended
for this application.
Installation must comply with all applicable plumbing codes.
PLUMBING REQUIREMENTS
1/4"
Water Supply
Pressure
7"
E
I N T E G R AT E D
(178)
35–120 psi (2.4–8.3 bar)
Excess Line for Connection
6"
(152)
75 1/2" (1918)
FROM FLOOR
RIGHT SIDE
OF OPENING
RIGHT SIDE
OF OPENING
Electrical supply location.
18" (457)
6" (152)
3" (76)
AREA EXTENDS 1/2" (13)
UNDERCOUNTER
WINE
FORWARD ON FLOOR
Water supply location.
18
|
Sub-Zero Customer Care 800.222.7820
OD copper, braided stainless
steel or PEX tubing
36" (914)
B UILT-IN R EF R IGE RATION
B U I L T- I N
Custom Panels
For framed, overlay and flush inset applications, custom
door panels must be provided. Handle hardware must
also be provided for overlay and flush inset applications.
Refer to panel requirements below and the charts on pages
22–27 for custom panel dimensions for your specific design
application.
Finish all sides of the custom panels. They may be visible
when the door is open or through the window of glass door
models.
PANEL REQUIREMENTS
W E I G H T P E R PA N E L
BI-36R, BI-36RG, BI-36F
All Other Models
Grille Panel
If the custom panel is thinner than 1/4" (6), a filler material
must be added to achieve a proper fit. If the panel is thicker
than 1/4" (6), rout an edge around the panel or mount the
custom panel on a sheet of 1/4" (6) thick material and insert
into the channel. Refer to the illustrations below.
Routing, recessing or optional extended handles may be
required for finger clearance. Refer to the full-scale template
on page 34.
When installing two units side by side, refer to page 16 for
dual standard installations.
75 lb (34 kg)
50 lb (23 kg)
13 lb (6 kg)
MIN
1/4"
5/8"
1/4" (6) TRIM REVEAL
(6)
(16)
1/4" (6) PANEL
DOOR
Panel 1/4" thick or less.
1/4" (6) min
I N T E G R AT E D
PA N E L T H I C K N E S S
Framed
Overlay and Flush Inset
MA X
The framed application is an overlay model with framed
design features. It is not a separate model.
PRO 48
IMPORTANT NOTE: Do not cover a glass door with a solid
panel.
FR AM ED PAN ELS
ROUT TO 1/4" (6)
DOOR
Panel thicker than 1/4".
WINE
|
19
UNDERCOUNTER
subzero.com/specs
B U I L T- I N
B UILT-IN R EF R IGE RATION
PRO 48
Custom Panels
PART IAL F R AME D OPTION
PAN EL M O U N TI N G K I T
The partial framed kit includes a stainless steel panel for
above and below the external dispenser. Refer to the chart
below for panel width. The kit is avail­able through an authorized Sub-Zero dealer. For local dealer information, visit the
find a showroom section of our website, subzero.com.
A Sub-Zero custom panel mounting kit eliminates the need
for a backer and spacer panel and is avail­able through an
authorized Sub-Zero dealer. For local dealer information, visit
the find a showroom section of our website, subzero.com.
The kit consists of mounting cleats, screws and gages used
to properly position the cleats. The kit is available for all
built-in models except glass door models. Dual installations
require two mounting kits.
PARTIAL FRAMED PANEL
W
BI-42SD
15 1/16"
(383)
BI-48SD
18 3/4"
(476)
O VER LAY PA N ELS
Overlay panels are typically created by combining a 3/4" (19)
custom panel, a .10" (3) spacer panel and a 1/4" (6) backer
panel. Refer to the illustrations below.
I N T E G R AT E D
When installing two units side by side, refer to page 16 for
dual standard installations.
CUSTOM
PANEL
SPACER PANEL
SPACER
PANEL
CUSTOM PANEL
BACKER PANEL
BACKER
PANEL
TRIM
5/16" (8) min
1/8" (3) (OVERLAY)
(19)
typical
.10" (3) 1/4" (6)
Panel assembly (cross section). Panel assembly (rear view).
WINE
UNDERCOUNTER
3/4"
20
|
Sub-Zero Customer Care 800.222.7820
B UILT-IN R EF R IGE RATION
B U I L T- I N
Custom Panels
F LUS H INS ET PA NE L S
I C E A N D WATER D I S P EN S ER
The flush inset application is an overlay model with flush
inset panels. It is not a separate model.
For models BI-42SD and BI‑48SD, the refrigerator door
panel must include a cut-out to accommodate the external
dispenser. The thickness of the panel in this area can range
from 1/4" (6) to a maximum of 1 1/8" (29). Refer to the illustrations below.
For flush inset panels thicker than 3/4" (19), a 90° door stop
may be required to prevent interference with adjacent
cabinets. Refer to the full-scale templates at the end of this
guide.
PRO 48
The flush inset design allows custom panels to be installed
flush with adjacent cabinets. Similar to overlay, flush inset
panels are typically created by combining a 3/4" (19) custom
panel, a .10" (3) spacer panel and a 1/4" (6) backer panel.
Refer to the illustrations for overlay panels.
5/8"
3/32"
3/16"
(16)
(2)
(5)
When installing two units side by side, refer to page 17 for
dual flush inset installations.
6 5/16" (160)
6 5/16" (160)
12 7/8"
(327)
(327)
Dispenser dimensions.
I N T E G R AT E D
12 7/8"
Dispenser dimensions.
2"
(51)
WINE
HANDLE
GLASSWELL
1"
(25)
Handle placement.
|
21
UNDERCOUNTER
subzero.com/specs
B U I L T- I N
B UILT-IN R EF R IGE RATION
Framed Panel Dimensions
H H
H H H
H H
A A
H H AH A
A A A
H H
H H H
H AH AH H
A AH A
H H
H H AH A
H H
W W W W W
I N T E G R AT E D
BI-30U, BI-36U(ID)
H H H
H H
W
H
35 3/4" (908)
69 9/16" (1767)
W
H H H H H H
8 15/16" (227)
GRI L L E ( O P T I O N A L) H H H H H
35 3/4" (908)
BI-36RG
A
5 3/16A" A(132)
A
Stiles | Rails
B B
B
A A
10 5/16" (262)
W
(1268)
W
H
29 3/4" (756)
18 11/16" (475)
GRI L L E ( O P T I O N A L)
Grille Panel
H H
H H H
H H
H H H
W W W W W
BI-30UG, BI-36UG
W W W W W
BI-36UFD(ID),
BI-42UFD(ID)
REFRIGERATOR
Door Panel
FREEZER
Drawer Panel
GRIL L E (OPTION AL )
Grille Panel
W
H
35 3/4" (908)
49 15/16" (1268)
W
H
35 3/4" (908)
18 11/16" (475)
W
H
35 3/4" (908)
8 15/16" (227)
A
5 3/16" (132)
H
W W W3 W W
W W W W W
29 /4" (756)
49 15/16"
FREEZER
Drawer Panel
W W W WWWW W W W
A A A
Stiles | Rails
R E F R I G E R AT O R
W W W W W
W
H H H
BI-36U G
B B B
MODEL BI-30U, BI-30UG
W W W W
Door
Panel
H H
MODEL BI-36U(ID), BI-36UG
R E F R I G E R AT O R / F RE E Z E R
Grille Panel
A AH A
H AH AH H
H H H
MODEL BI-36R, BI-36RG, BI-36F
Door Panel
H H H
H H H
W W W W W
BI-36RG
H H
H H
A A A
B B B
W W W W W
BI-36R, BI-36F
WINE
A A A
A A
B B
H H H
H H
A A
PRO 48
H H
H H H
A A A
W
H
29 3/4" (756)
8 15/16" (227)
BI-30UG
Stiles | Rails
A
5 3/16" (132)
MODEL BI-36UFD(ID)
REFRIGERATOR (2 PAN EL S)
Door Panel
FREEZER
Drawer Panel
GRIL L E (OPTION AL )
Grille Panel
W
H
17 5/8" (448)
49 15/16" (1268)
W
H
35 3/4" (908)
18 11/16" (475)
W
H
35 3/4" (908)
8 15/16" (227)
MODEL BI-42UFD(ID)
REFRIGERATOR (2 PAN EL S)
Door Panel
FREEZER
Drawer Panel
UNDERCOUNTER
GRIL L E (OPTION AL )
Grille Panel
22
|
Sub-Zero Customer Care 800.222.7820
W
H
20 5/8" (524)
49 15/16" (1268)
W
H
41 3/4" (1060)
18 11/16" (475)
W
H
41 3/4" (1060)
8 15/16" (227)
B UILT-IN R EF R IGE RATION
WW
AA
HH
HH
B U I L T- I N
HH
WW
BB
WW
WW
WW
WW
WW
Framed Panel Dimensions
HH
HH
HH
HH
PRO 48
AA
BB
WW
WW
BI-36S, BI-42S(ID),
BI-48S(ID)
WW
WW
BI-42SD, BI-48SD
MODEL BI-48S, BI-48SID, BI-48SD
R E F R I G E R AT O R
Door Panel
W
H
19 13/16" (503)
69 9/16" (1767)
FREEZER
Door Panel
W
H
15 7/16" (392)
69 9/16" (1767)
GRI L L E ( O P T I O N A L)
Grille Panel
W
H
35 3/4" (908)
8 15/16" (227)
REFRIGERATOR
Door Panel
FREEZER
Door Panel
GRIL L E (OP TION AL )
Grille Panel
BI-48SD
Dispenser Cut-Out*
MODEL BI-42S, BI-42SID, BI-42SD
R E F R I G E R AT O R
Door Panel
FREEZER
Door Panel
GRI L L E ( O P T I O N A L)
BI-42SD
Dispenser Cut-Out*
Cut-Out Location
H
24 13/16" (630)
69 9/16" (1767)
W
H
16 7/16" (418)
69 9/16" (1767)
W
H
41 3/4" (1060)
8 15/16" (227)
W
H
5 7/8" (149)
12 7/16" (316)
A
B
1 7/8" (48)
28 3/4" (730)
Cut-Out Location
H
69 9/16" (1767)
W
H
18 3/4" (476)
69 9/16" (1767)
W
H
47 3/4" (1213)
8 15/16" (227)
W
H
5 7/8" (149)
12 7/16" (316)
A
B
1 7/8" (48)
28 3/4" (730)
*For models BI-42SD and BI-48SD, panel thickness in dispenser area can
range from 1/4" (6) to 1 1/8" (29) max. If panel is thicker, rout out 1/4" (6) min flat
landing area to accommodate dispenser.
WINE
Grille Panel
W
W
28 1/2" (724)
I N T E G R AT E D
MODEL BI-36S
|
23
UNDERCOUNTER
subzero.com/specs
B U I L T- I N
B UILT-IN R EF R IGE RATION
Overlay Panel Dimensions
H H
H H H
H H
H H AH A
H H
H H H
A A A
H AH AH H
A AH A
H H
H H AH A
H H
W W W W W
I N T E G R AT E D
BI-30U, BI-36U(ID)
H H H
H H
H H H
W
H
36" (914)
35 1/8" (892)
35 3/4" (908)
69 3/4" (1772)
15/16" (1751)
68
H H H H H
69 9/16" (1767)
GRI L L E
Overlay Panel
Spacer Panel
Backer Panel
W
H
36"
(914)
A A A
35 1/8" (892)
B B
35 3/4" (908)
9 1/4" (235)*
8 5/16" (211)
B
8 15/16" (227)
BI-36RG
Stiles | Rails
W W W W W
W W W W W
A A
B B
A
B
5 1/4" (133)
10 3/8" (264)
W
H
30" (762)
29 1/8" (740)
29 3/4" (756)
50 1/8" (1273)
49 5/16" (1253)
49 15/16" (1268)
W
H
30" (762)
29 1/8" (740)
29 3/4" (756)
19" (483)
18 1/16" (459)
18 11/16" (475)
W W W W W
W W W W W
MODEL BI-30U, BI-30UG
WINE
R EF R I G E R AT O R
Overlay Panel
Spacer Panel
Backer Panel
FREEZER
Overlay Panel
Spacer Panel
Backer Panel
GRI L L E
Overlay Panel
Spacer Panel
Backer Panel
W
H
30" (762)
29 1/8" (740)
29 3/4" (756)
9 1/4" (235)*
8 5/16" (211)
8 15/16" (227)
BI-30UG
Stiles | Rails
24
|
H H
H H H
W W W WWWW W W W
A A A
H H
H H H
H H
H H H
W W W W W
BI-30UG, BI-36UG
W W W W W
BI-36UFD(ID),
BI-42UFD(ID)
MODEL BI-36U(ID), BI-36UG
R E F R I G E R AT O R | F RE E Z E R
H H
A AH A
H AH AH H
H H H
MODEL BI-36R, BI-36RG, BI-36F
Overlay Panel
Spacer Panel
Backer Panel
H H H
H H H
W W W W W
BI-36RG
H H
H H
A A A
B B B
W W W W W
BI-36R, BI-36F
UNDERCOUNTER
A A A
A A
B B
H H H
H H
A A
PRO 48
H H
H H H
A A A
A A
Sub-Zero Customer Care 800.222.7820
A
5 1/4" (133)
REFRIGERATOR
Overlay Panel
Spacer Panel
Backer Panel
FREEZER
Overlay Panel
Spacer Panel
Backer Panel
GRIL L E
Overlay Panel
Spacer Panel
Backer Panel
W
H
36" (914)
35 1/8" (892)
35 3/4" (908)
50 1/8" (1273)
49 5/16" (1253)
49 15/16" (1268)
W
H
36" (914)
35 1/8" (892)
35 3/4" (908)
19" (483)
18 1/16" (459)
18 11/16" (475)
W
H
36" (914)
35 1/8" (892)
35 3/4" (908)
9 1/4" (235)*
8 5/16" (211)
8 15/16" (227)
BI-36U G
A
5 1/4" (133)
Stiles | Rails
MODEL BI-36UFD(ID)
REFRIGERATOR (2 PAN EL S)
Overlay Panel
Spacer Panel
Backer Panel
FREEZER
Overlay Panel
Spacer Panel
Backer Panel
GRIL L E
Overlay Panel
Spacer Panel
Backer Panel
W
H
17 7/8" (454)
17" (432)
17 5/8" (448)
50 1/8" (1273)
49 5/16" (1253)
49 15/16" (1268)
W
H
36" (914)
35 1/8" (892)
35 3/4" (908)
19" (483)
18 1/16" (459)
18 11/16" (475)
W
H
36" (914)
35 1/8" (892)
35 3/4" (908)
9 1/4" (235)*
8 5/16" (211)
8 15/16" (227)
B UILT-IN R EF R IGE RATION
WW
AA
HH
HH
B U I L T- I N
HH
WW
BB
WW
WW
WW
WW
WW
Overlay Panel Dimensions
HH
MODEL BI-42S, BI-42SID, BI-42SD
HH
REFRIGERATOR
HH
Overlay Panel
Spacer Panel
Backer Panel
HH
W
H
25 1/16" (637)
24 3/16" (614)
24 13/16" (630)
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
FREEZER
AA
BB
WW
WW
BI-36S, BI-42S(ID),
BI-48S(ID)
WW
W
H
16 11/16" (424)
15 13/16" (402)
16 7/16" (418)
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
GRIL L E
Overlay Panel
Spacer Panel
Backer Panel
WW
W
H
42" (1067)
41 1/8" (1045)
41 3/4" (1060)
9 1/4" (235)*
8 5/16" (211)
8 15/16" (227)
BI-42SD
BI-42SD, BI-48SD
Dispenser Cut-Out
W
H
5 7/8" (149)
12 7/16" (316)
Cut-Out Location
R E F R I G E R AT O R ( 2 PANE LS)
Overlay Panel
Spacer Panel
Backer Panel
FREEZER
Overlay Panel
Spacer Panel
Backer Panel
GRI L L E
Overlay Panel
Spacer Panel
Backer Panel
MODEL BI-48S, BI-48SID, BI-48SD
W
H
20 7/8" (530)
20" (508)
20 5/8" (524)
50 1/8" (1273)
49 5/16" (1253)
49 15/16" (1268)
W
H
42" (1067)
41 1/8" (1045)
41 3/4" (1060)
19" (483)
18 1/16" (459)
18 11/16" (475)
W
H
42" (1067)
41 1/8" (1045)
41 3/4" (1060)
9 1/4" (235)*
8 5/16" (211)
8 15/16" (227)
REFRIGERATOR
Overlay Panel
Spacer Panel
Backer Panel
FREEZER
Overlay Panel
Spacer Panel
Backer Panel
GRIL L E
Overlay Panel
Spacer Panel
Backer Panel
BI-48SD
Dispenser Cut-Out
Overlay Panel
Spacer Panel
Backer Panel
FREEZER
Overlay Panel
Spacer Panel
Backer Panel
GRI L L E
H
20 1/16" (510)
19 3/16" (487)
19 13/16" (503)
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
W
H
15 11/16" (398)
14 13/16" (376)
15 7/16" (392)
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
W
H
36" (914)
35 1/8" (892)
35 3/4" (908)
9 1/4" (235)*
8 5/16" (211)
8 15/16" (227)
Cut-Out Location
H
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
W
H
19" (483)
18 1/8" (460)
18 3/4" (476)
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
W
H
48" (1219)
47 1/8" (1197)
47 3/4" (1213)
9 1/4" (235)*
8 5/16" (211)
8 15/16" (227)
W
H
5 7/8" (149)
12 7/16" (316)
A
B
2" (51)
28 13/16" (732)
*Panel height may be increased by 7/16" (11) to hide upper main frame. Also
refer to built-in panel configurator at subzero.com/trade/panels.
Grille panel dimensions are for standard 84" (2134) overall unit height. For
83" (2108) height, subtract 1" (25) from grille panel height dimensions and for
88" (2235) height, add 4" (102). A specific panel grille must be ordered for an
83" or 88" overall unit height.
subzero.com/specs
|
25
UNDERCOUNTER
Overlay Panel
Spacer Panel
Backer Panel
W
W
28 3/4" (730)
27 7/8" (708)
28 1/2" (724)
WINE
MODEL BI-36S
R EF R I G E R AT O R
B
28 13/16" (732)
I N T E G R AT E D
MODEL BI-42UFD(ID)
A
2" (51)
PRO 48
Overlay Panel
Spacer Panel
Backer Panel
B U I L T- I N
B UILT-IN R EF R IGE RATION
Flush Inset Panel Dimensions
H H
H H H
H H
H H AH A
H H
H H H
A A A
H AH AH H
A AH A
H H
H H AH A
H H
W W W W W
I N T E G R AT E D
BI-30U, BI-36U(ID)
H H H
H H
H H H
WINE
BI-30UG, BI-36UG
W W W W W
BI-36UFD(ID),
BI-42UFD(ID)
W
H
50 1/8" (1273)
49 5/16" (1253)
49 15/16" (1268)
W
H
37"
(940)
A A A
35 1/8" (892)
B B
35 3/4" (908)
9 1/4" (235)
8 5/16" (211)
B
8 15/16" (227)
A A
B B
R EF R I G E R AT O R
W
H
Flush Inset Panel
Spacer Panel
Backer Panel
31" (787)
29 1/8" (740)
29 3/4" (756)
50 1/8" (1273)
49 5/16" (1253)
49 15/16" (1268)
W
H
31" (787)
29 1/8" (740)
29 3/4" (756)
19" (483)
18 1/16" (459)
18 11/16" (475)
W W W W W
W W W W W
FREEZER
GRI L L E
W
H
31" (787)
29 1/8" (740)
29 3/4" (756)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
BI-30UG
|
W W W W W
37" (940)
35 1/8" (892)
35 3/4" (908)
MODEL BI-30U, BI-30UG
26
H H H
Flush Inset Panel
Spacer Panel
Backer Panel
B
Stiles | Rails
H H
REFRIGERATOR
10 3/8" (264)
Flush Inset Panel
Spacer Panel
Backer Panel
H H H
69 3/4" (1772)
15/16" (1751)
68
H H H H H
69 9/16" (1767)
A
Flush Inset Panel
Spacer Panel
Backer Panel
H H
37" (940)
35 1/8" (892)
35 3/4" (908)
5 3/4" (146)
W W W W W
W W W W W
W W W WWWW W W W
B B B
H
BI-36RG
Stiles | Rails
H H H
W
GRI L L E
Flush Inset Panel
Spacer Panel
Backer Panel
H H
MODEL BI-36U(ID), BI-36UG
R E F R I G E R AT O R | F RE E Z E R
H H
H AH AH H
A AH A
H H H
MODEL BI-36R, BI-36RG, BI-36F
Flush Inset Panel
Spacer Panel
Backer Panel
H H H
H H H
W W W W W
BI-36RG
H H
H H
B B B
B B B
W W W W W
BI-36R, BI-36F
UNDERCOUNTER
A A A
B A
B B
H H H
H H
B A
PRO 48
H H
H H H
A A A
A A
A
B
5 3/4" (146)
5 1/4" (133)
Sub-Zero Customer Care 800.222.7820
FREEZER
Flush Inset Panel
Spacer Panel
Backer Panel
GRIL L E
Flush Inset Panel
Spacer Panel
Backer Panel
BI-36U G
Stiles | Rails
W
H
37" (940)
35 1/8" (892)
35 3/4" (908)
19" (483)
18 1/16" (459)
18 11/16" (475)
W
H
37" (940)
35 1/8" (892)
35 3/4" (908)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
A
B
5 3/4" (146)
5 1/4" (133)
MODEL BI-36UFD(ID)
REFRIGERATOR (2 PAN EL S)
Flush Inset Panel
Spacer Panel
Backer Panel
FREEZER
Flush Inset Panel
Spacer Panel
Backer Panel
GRIL L E
Flush Inset Panel
Spacer Panel
Backer Panel
W
H
18 3/8" (467)
17" (432)
17 5/8" (448)
50 1/8" (1273)
49 5/16" (1253)
49 15/16" (1268)
W
H
37" (940)
35 1/8" (892)
35 3/4" (908)
19" (483)
18 1/16" (459)
18 11/16" (475)
W
H
37" (940)
35 1/8" (892)
35 3/4" (908)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
B UILT-IN R EF R IGE RATION
WW
AA
HH
HH
B U I L T- I N
HH
WW
BB
WW
WW
WW
WW
WW
Flush Inset Panel Dimensions
HH
MODEL BI-42S, BI-42SID, BI-42SD
HH
HH
HH
REFRIGERATOR
W
H
Flush Inset Panel
Spacer Panel
Backer Panel
25 9/16" (649)
24 3/16" (614)
24 13/16" (630)
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
FREEZER
AA
BB
WW
WW
BI-36S, BI-42S(ID),
BI-48S(ID)
WW
W
H
17 3/16" (437)
15 13/16" (402)
16 7/16" (418)
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
GRIL L E
Flush Inset Panel
Spacer Panel
Backer Panel
WW
W
H
43" (1092)
41 1/8" (1045)
41 3/4" (1060)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
BI-42SD
BI-42SD, BI-48SD
Dispenser Cut-Out
W
H
5 7/8" (149)
12 7/16" (316)
Cut-Out Location
R E F R I G E R AT O R ( 2 PANE LS)
Flush Inset Panel
Spacer Panel
Backer Panel
FREEZER
Flush Inset Panel
Spacer Panel
Backer Panel
GRI L L E
Flush Inset Panel
Spacer Panel
Backer Panel
MODEL BI-48S, BI-48SID, BI-48SD
W
H
REFRIGERATOR
W
H
21 3/8" (543)
20" (508)
20 5/8" (524)
50 1/8" (1273)
49 5/16" (1253)
49 15/16" (1268)
Flush Inset Panel
Spacer Panel
Backer Panel
29 1/4" (743)
27 7/8" (708)
28 1/2" (724)
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
W
H
43" (1092)
41 1/8" (1045)
41 3/4" (1060)
19" (483)
18 1/16" (459)
18 11/16" (475)
W
H
43" (1092)
41 1/8" (1045)
41 3/4" (1060)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
FREEZER
Flush Inset Panel
Spacer Panel
Backer Panel
GRIL L E
Flush Inset Panel
Spacer Panel
Backer Panel
BI-48SD
Dispenser Cut-Out
R E F R I G E R AT O R
W
H
Flush Inset Panel
Spacer Panel
Backer Panel
20 9/16" (522)
19 3/16" (487)
19 13/16" (503)
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
FREEZER
GRI L L E
H
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
W
H
37" (940)
35 1/8" (892)
35 3/4" (908)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
H
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
W
H
49" (1245)
47 1/8" (1197)
47 3/4" (1213)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
W
H
5 7/8" (149)
12 7/16" (316)
A
B
2" (51)
28 13/16" (732)
Grille panel dimensions are for standard 84" (2134) overall unit height. For
83" (2108) height, subtract 1" (25) from grille panel height dimensions and for
88" (2235) height, add 4" (102). A specific panel grille must be ordered for an
83" or 88" overall unit height.
subzero.com/specs
|
27
UNDERCOUNTER
Flush Inset Panel
Spacer Panel
Backer Panel
W
16 3/16" (411)
14 13/16" (376)
15 7/16" (392)
Cut-Out Location
W
19 1/2" (495)
18 1/8" (460)
18 3/4" (476)
WINE
MODEL BI-36S
Flush Inset Panel
Spacer Panel
Backer Panel
B
28 13/16" (732)
I N T E G R AT E D
MODEL BI-42UFD(ID)
A
2" (51)
PRO 48
Flush Inset Panel
Spacer Panel
Backer Panel
B UILT-IN R EF R IGE RATION
TOP VIEW
TOP VIEW
B U I L T- I N
BACKER
CABINETRY
SPACER
BACKER
SPACER
PANEL O F F S ET
5/16" (8)
BACKER
SPACER
PRO 48
IL L U S
Door (hinge) | Drawer | Grille Sides
Doors (handle) Sides (French door only)
Grille Top
Grille Bottom | Door Top
Door Bottom | Drawer Top
Drawer Bottom
SI D E - B Y- S I D E
Doors (hinge) | Grille Sides
Doors (handle) Sides
Grille Top
Grille Bottom | Door Top
Door Bottom
5/16A
" (8)
A
B
GRILLE
C
CABINETRY
D
E
F
IL L U S
GRILLE
A
B
C
D
F
CABINETRY
GRILLE
1/2"
(13)
CABINETRY
5/8"
(16)
5/8"
(16)
5/16" (8)
1/2"
(13)
CABINETRY
1/2" (13)
5/8"
(16)
1/2"
(13)
1/8"
5/16" (3) GRILLE
(8)
CABINETRY
1/2" (13)
1/8"
5/16VIEW
SIDE
" (3)GRILLE
(8)
CABINETRY
1/2" (13)
1/8"
5/16
" (3)
GRILLE
SIDE
VIEW
(8)
WINE
5/16"
5/32
3/DRAWER
(8)
"32"
5/16" (4)(2)
(8)
DOOR
/8" (16)
5/16"
DRAWER
35//32
(8)
Illus.
32"E
"
5/16" (2)
(4)
(8) DOOR
UNDERCOUNTER
5/8" (16)
SIDE VIEW
DRAWER
5/DRAWER
32"
5/16" (4)
(8)
SIDE VIEW
28
|
Sub-Zero Customer Care 800.222.7820
5/16" (8)
5/16" (8)
DOOR
1/8" (3)
DOOR
DOOR
1/8" (3)
DOOR
1/4" (6)
1/4" (6)
REVEAL
5/16" (8)
5/16" (8)
1/8" (3)
1/8" (3)
1/4" (6)
REVEAL
1/2" (13)
5/16" DOOR
3/32
5/"32GRILLE
"
5/16(8)
" (2)(4)
(8)
DOOR
GRILLE
5/16"
35/32"
/32"
5/(8)
16" (2)
(4)
(8)
SIDE VIEW
SIDE VIEW
1/2" (13)
1/2
5/16"
DOOR
GRILLE
32
(8) 53//32
""
5/16" (4)
(2)
(8)
DOOR
GRILLE
1/8"
5/16
" (3)
SIDE
VIEW
(8)
5/16"
32""
(8) 53//32
5/16" (4)
(2)
(8)
SIDE VIEW
SIDE VIEW
1/2" (13)
Illus.DOOR
D
SIDE VIEW
1/2
1/2" (13)
1/8"
5SIDE
VIEW
/16" (3)
(8)
1/2" (13)
5/16"
(8) 5/32"
(4)
5/16"
(8) 5/32" GRILLE
(4)
GRILLE
1/8"
5/16" (3)
(8)
1/2" (13)
REVEAL
1/2
DOOR
3/32"
5/16" (2)
(8)
SIDE VIEW
DOOR /
DRAWER
3/32"
5/16" (2)
(8)
DOOR /
DRAWER
SIDE VIEW
DOOR
SIDE VIEW
5
DOOR
TOP VIEW REVEAL
5/16"
(8) 3/32"
(2)
5/8" (16)
DRAWER
TOP VIEWREVEAL
Illus. B
SIDE VIEW
DOOR
DOOR
1/4" (6)
1/4" (6)
1/4" (6)
Illus. A
5/16"
(8) 3/32"
(2)
DRAWER
1/8" (3)
DOOR
DOOR
1/8DOOR
" (3)
REVEAL
Illus. C
DOOR
5/16" (8)
5/16" (8)
FLUSH INSET PANEL
IL L U S
OV E R - A N D - U N D E R
5/CABINETRY
8"
(16)
5/16" (8)
BACKER
CABINETRY
FLUSH INSET PANEL
C
D
CABINETRY
F
1/2"
(13)
TOP VIEW
5/8"
SPACER
(16)
Door | Grille Sides
Grille Top
Grille Bottom | Door Top
Door Bottom
TOP VIEW
DOOR / DRAWER / GRILLE
FLUSH INSET PANEL
1/2"
(13)
PANEL OFFSET
A L L R E F R I G E R AT O R | ALL FREE Z E R
5/16" (8)
BACKER
5/8"CABINETRY
SPACER
TOP VIEW (16)
BACKER
SPACER
TOP VIEW
DOOR
DOOR / DRAWER / GRILLE
FLUSH INSET PANEL
1/2"
(13)
The illustrations provide panel offsets and reveals for built-in
models in a flush inset application. Refer to the chart below
5/16" (8)
for reference to the illustrations.
DOOR DOOR
DOOR
TOP VIEW
DOOR / DRAWER / GRILLE
FLUSH INSET PANEL
I N T E G R AT E D
CABINETRY
TOP VIEW
DOOR / DRAWER / GRILLE
FLUSH INSET PANEL
Flush Inset Panels
TOP VIEW
TOP VIEW
DOOR / DRAWER / GRILLE
DOOR / DRAWER / GRILLE
5/8" (16)
DOOR /
DRAWER
5/16"
(8)
DOOR /
DRAWER
5/16"
(8)
5/16"
(8) 53/32"
5/16" (4)
(2)
(8)
SIDE VIEW
5
SIDE VIEW
DOOR /
DRAWER
/8" (16)
5/16"
(8) 35//32
32""
5/16" (2)
(4)
(8)
5/8" (16)
SIDE VIEW
3/32"
(2)
SIDE VIEW
5/16"
DOOR /
(8) DRAWER
3
5/16"
(8)
Illus. F
SIDE VIEW
3/32"
5/16" (2)
(8)
3
SIDE VIEW
5/16"
(8)
5/32"
5/16" (4)
(8)
SIDE VIEW
SIDE VIEW
3/32"
(2)
3
SIDE VIEW
B UILT-IN R EF R IGE RATION
B U I L T- I N
Dual Installation
For dual standard installations, panel dimensions are the
same as for single installations. Refer to the charts on pages
22–25. Panel dimensions and offsets for dual flush inset
installations are listed on the following pages.
PRO 48
If two units are installed side by side, a dual installation kit
may be required. Installations without a custom filler strip
require a dual installation kit. If a dual installation kit is not
specified, a 2" (51) filler strip is recommended between units.
A custom filler strip is required when installing two French
door or side-by-side models. Dual installations without a
filler strip can only be accomplished using two units with
opposite hinges. Refer to the illustrations below.
Dual installation kits are available through an authorized
Sub-Zero dealer. For local dealer information, visit the find a
showroom section of our website, subzero.com. For questions regarding the installation, call Sub‑Zero customer care
at 800-222-7820.
I N T E G R AT E D
WITHOUT FILLER STRIP
Opposite hinges.
FILLER STRIP
Same side hinges.
WINE
|
29
UNDERCOUNTER
subzero.com/specs
B U I L T- I N
B UILT-IN R EF R IGE RATION
Dual Flush Inset Panel Dimensions
H H
H H
H H
H H
H H
H H A AH AH A
A AH H
H H
W W
W W
BI-36R, BI-36F
B B
H H
W W
W W
BI-36RG
I N T E G R AT E D
W W
W W
W W
W
H
36 1/2" (927)
35 1/8" (892)
35 3/4" (908)
50 1/8" (1273)
49 5/16" (1253)
49 15/16" (1268)
W
H
36 1/A2" A(927)
35 1/8" (892)
B B
35 3/4" (908)
9 1/4"A(235)
A
8 5/16" (211)
B
8 15/16" (227)
W
W
WW
A
B
5 3/4" (146)
10 3/8" (264)
W W
W W
30 1/2" (775)
29 1/8" (740)
29 3/4" (756)
50 1/8" (1273)
49 5/16" (1253)
49 15/16" (1268)
FREEZER
W
H
30 1/2" (775)
29 1/8" (740)
29 3/4" (756)
19" (483)
18 1/16" (459)
18 11/16" (475)
GRI L L E
W
H
30 1/2" (775)
29 1/8" (740)
29 3/4" (756)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
BI-30UG
A
B
5 3/4" (146)
5 1/4" (133)
Sub-Zero Customer Care 800.222.7820
FREEZER
B
W W
Flush Inset Panel
Spacer Panel
Backer Panel
|
BI-30UG, BI-36UG
Flush Inset Panel
Spacer Panel
H H
Backer Panel
H
30
W W
W W
REFRIGERATOR
W
Stiles | Rails
H H
H H
69 3/4" (1772)
15/16" (1751)
68
H H
69 9/16" (1767)
R EF R I G E R AT O R
Flush Inset Panel
Spacer Panel
Backer Panel
W W
36 1/2" (927)
35 1/H8" H(892)
35 3/4" (908)
MODEL BI-30U, BI-30UG
Flush Inset Panel
Spacer Panel
Backer Panel
W W
W W
W W
H
BI-36RG
Stiles | Rails
H H
W
GRI L L E
Flush Inset Panel
Spacer Panel
Backer Panel
H H
MODEL BI-36U(ID), BI-36UG
R E F R I G E R AT O R | F RE E Z E R
H H
A AH H
H H
H H
MODEL BI-36R, BI-36RG, BI-36F
Flush Inset Panel
Spacer Panel
Backer Panel
H H
H H
H H
W W
BI-30U, BI-36U(ID)
H H
H H
WINE
W W
W W
H H
W W
B B
B A
B B
H H
B B
H H A AH AH A
A A
H H
UNDERCOUNTER
H H
B A
PRO 48
A A
H H
H H
A A
A A
Flush Inset Panel
Spacer Panel
Backer Panel
GRIL L E
Flush Inset Panel
Spacer Panel
Backer Panel
BI-36U G
Stiles | Rails
W
H
36 1/2" (927)
35 1/8" (892)
35 3/4" (908)
19" (483)
18 1/16" (459)
18 11/16" (475)
W
H
36 1/2" (927)
35 1/8" (892)
35 3/4" (908)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
A
B
5 3/4" (146)
5 1/4" (133)
Grille panel dimensions are for standard 84" (2134) overall unit height. For
83" (2108) height, subtract 1" (25) from grille panel height dimensions and for
88" (2235) height, add 4" (102). A specific panel grille must be ordered for an
83" or 88" overall unit height. For dual wide grilles, refer to page 32.
B UILT-IN R EF R IGE RATION
TOP VIEW
TOP VIEW
CABINETRY
TOP VIEW
Dual Installation
D U AL F LUS H IN SE T PANE L OFFSE T
BACKER
5/8"CABINETRY
(16) SPACER
IL L U S
Door (hinge) | Grille Sides
Door (handle) Sides
Grille Top
Grille Bottom | Door Top
Door Bottom
A
B
C
CABINETRY
D
F
OV E R - A N D - U N D E R
IL L U S
TOP VIEW
GRILLE
5/CABINETRY
8"
(16)
5/16" (8)
1/2"
(13)
BACKER
1/2"
(13)
CABINETRY
5/8"
(16)
5/16" (8)
CABINETRY
1/2" (13)
5/8"
(16)
1/2"
(13)
5/16" (8)
5/16" (8)
DOOR
1/8" (3)
DOOR
DOOR
1
/8" (3)
DOOR
1/4" (6)
1/4" (6)
REVEAL
1/8" (3)
1/8" (3)
CABINETRY
1/2" (13)
1/8"
5/16VIEW
SIDE
" (3)GRILLE
CABINETRY
1/4" (6)
REVEAL
REVEAL
1/2" (13)
1/8"
5/16" (3)
(8)
1/2" (13)
1/2
1/2" (13)
5/16" DOOR
3/32
5/"32GRILLE
"
5/16(8)
" (2)(4)
(8)
DOOR
GRILLE
1/8"
5SIDE
VIEW
/16" (3)
(8)
5/16"
35/32"
/32"
5/(8)
16" (2)
(4)
(8)
SIDE VIEW
SIDE VIEW
1/2" (13)
DOOR
1/2
5/16"
32""
(8) 53//32
5/16" (4)
(2)
(8)
DOOR
3/32
GRILLE
"
5/16" (2)
(8)
1/8"
5/16
" (3)
SIDE
VIEW
(8)
SIDE VIEW
SIDE VIEW
1/2
DOOR
Illus. D
SIDE VIEW
5/16"
(8) 5/32"
(4)
5/16"
(8) 5/32" GRILLE
(4)
GRILLE
Illus. B
1/8"
5/16" (3) GRILLE
(8)
(8)
5/16" (8)
5/16" (8)
1/4" (6)
Illus. A
3/32"
5/16" (2)
(8)
DOOR /
DRAWER
DOOR /
DRAWER
SIDE VIEW
5/16"
(8) 3/32"
(2)
5/16"
(8) 3/32"
(2)
DOOR
5/16"
5/32
3/DRAWER
(8)
"32"
5/16" (4)(2)
(8)
DOOR
SIDE VIEW
5
/8" (16)
5/DRAWER
Illus.
32E
"
5/16" (4)
(8) DOOR
SIDE VIEW
DOOR /
DRAWER
5/16"
(8)
DOOR /
DRAWER
5/16"
(8) 53/32"
5/16" (4)
(2)
(8)
SIDE VIEW
5
SIDE VIEW
/8" (16)
5/16"
(8) 35//32
32""
5/16" (2)
(4)
(8)
5/8" (16)
SIDE VIEW
3/32"
(2)
SIDE VIEW
5/16"
DOOR /
(8) DRAWER
5/16"
(8)
3
5/16"
(8)
Illus. F
SIDE VIEW
3/32"
(2)
3
SIDE VIEW
5/32"
5/16" (4)
(8)
SIDE VIEW
SIDE VIEW
subzero.com/specs
|
31
5/16"
(8)
UNDERCOUNTER
DRAWER
5/8" (16)
WINE
5/8" (16)
DRAWER
TOP VIEW REVEAL
TOP VIEWREVEAL
REVEAL
Illus. C
DOOR
DOOR
1/4" (6)
1/4" (6)
FLUSH INSET PANEL
GRILLE
SIDE VIEW
DRAWER
1/8" (3)
DOOR
DOOR
1/8DOOR
" (3)
DUAL
TRIM
1/2" (13)
DOOR
5/16" (8)
5/16" (8)
I N T E G R AT E D
A
B
CABINETRY
C
D
E
F
GRILLE
TOP VIEW
PRO 48
A L L R E F R I G E R AT O R | ALL FREE Z E R
1/2"
(13)
DOOR / DRAWER / GRILLE
FLUSH INSET PANEL
5/8"
SPACER
(16)
PANEL OFFSET
Door (hinge) | Drawer | Grille Sides
Door (handle) Sides
Grille Top
Grille Bottom | Door Top
Door Bottom | Drawer Top
Drawer Bottom
5/16" (8)
1/2"
(13)
The illustrations provide panel offsets and reveals for
built-in
FLUSH
INSET PANEL
models in a dual flush inset application. Refer to the chart
5/16" (8)
below for reference to the illustrations.
TOP VIEW
DOOR
DOOR / DRAWER / GRILLE
FLUSH INSET PANEL
5/16" (8)
BACKER
SPACER
DOOR DOOR
DOOR
TOP VIEW
DOOR / DRAWER / GRILLE
FLUSH INSET PANEL
B U I L T- I N
BACKER
CABINETRY
SPACER
BACKER
SPACER
TOP VIEW
TOP VIEW
DOOR / DRAWER / GRILLE
DOOR / DRAWER / GRILLE
3
B U I L T- I N
B UILT-IN R EF R IGE RATION
Dual Installation
D U AL WIDE G R IL L E
DUAL WIDE GRILLE—FLUSH INSET
PRO 48
A dual wide grille spans the entire width of both units in a
dual installation and is a part of a dual installation kit.
For overlay and flush inset panel dimensions for the dual
wide grille, refer to the charts below. Dimensions listed are
for a standard 84" (2134) finished height.
DUAL WIDE GRILLE—OVERLAY
T WO 3 0 " M O D E L S
Overlay Panel
Spacer Panel
Backer Panel
W
H
60 1/4" (1530)
59 3/8" (1508)
60" (1524)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
30" A N D 3 6 " M O D E L
Overlay Panel
Spacer Panel
Backer Panel
W
H
66 1/4" (1683)
65 3/8" (1661)
66" (1676)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
Overlay Panel
Spacer Panel
Backer Panel
W
H
72 1/4" (1835)
71 3/8" (1813)
72" (1829)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
WINE
I N T E G R AT E D
T WO 3 6 " M O D E L S
UNDERCOUNTER
TWO 30" MOD EL S
32
|
Sub-Zero Customer Care 800.222.7820
Flush Inset Panel
Spacer Panel
Backer Panel
30" AN D 36" MOD EL
Flush Inset Panel
Spacer Panel
Backer Panel
TWO 36" MOD EL S
Flush Inset Panel
Spacer Panel
Backer Panel
W
H
61 1/4" (1556)
59 3/8" (1508)
60" (1524)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
W
H
67 1/4" (1708)
65 3/8" (1661)
66" (1676)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
W
H
73 1/4" (1861)
71 3/8" (1813)
72" (1829)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
B UILT-IN R EF R IGE RATION
B U I L T- I N
Standard Handles
The custom side panels must be a minimum of 24" (610)
deep and 1/2" (13) thick. Routing will be necessary for the
side panel to fit flush against the side of the unit. Refer to
the illustrations below.
Optional stainless steel tubular and pro handles are avail­
able through an authorized Sub-Zero dealer. For local dealer
information, visit the find a showroom section of our
website, subzero.com.
When installing a built-in unit with a custom side panel, an
accessory kit is required. Stainless steel and white enamel
side panels are available through an authorized Sub-Zero
dealer. For local dealer information, visit the find a showroom section of our website, subzero.com.
Refer to the chart below for standard handle lengths for
built-in models.
24" (610)
FRONT
OF SIDE
PANEL
HANDLE LENGTH
TU BU L A R
PRO
Full Door
63 7/8"
Over-and-Under Door
44 1/4"
30" Drawer
24 5/16" (633)
17 9/16" (447)
36" Drawer
30 5/16" (770)
23 5/8" (600)
42" Drawer
36 5/16" (922)
29 5/8" (753)
(1622)
(1124)
45 3/16"
(1147)
37 1/2"
PRO 48
Side Panel
(952)
1" (25)
1 7/8" (48)
I N T E G R AT E D
1/8" (3)
1/2" (13)
ROUT TO 1/8" (3)
1 7/8"(48)
84"
1" (25)
MAIN
FRAME
SIDE PANEL
ROUTING
(2134)
Routing detail.
4 1/4" (108)
ROUT TO
3/16" (5)
(OVER-AND-UNDER
MODELS)
5 3/4"
(146)
20 1/2"
(521)
WINE
4" (102)
OPTIONAL
TOE KICK
CUT-OUT
2 5/8"
(67)
Side panel dimensions.
|
33
UNDERCOUNTER
subzero.com/specs
B U I L T- I N
B UILT-IN R EF R IGE RATION
Framed Panels
PRO 48
F ULL-S CALE T E MPL ATE
OPTIONAL EXTENDED
FULL-LENGTH HANDLE
I N T E G R AT E D
STANDARD
FULL-LENGTH HANDLE
2"
1"
(51)
(25)
3"
(76)
11/4" (32) PANEL
1" (25) PANEL
3/4" (19) PANEL
1/2" (13) PANEL
WINE
1/4" (6) FRAMED PANEL
DOOR
UNDERCOUNTER
Framed panel thickness.
34
|
Sub-Zero Customer Care 800.222.7820
B UILT-IN R EF R IGE RATION
B U I L T- I N
Overlay | Flush Inset Panels
F ULL-S CALE T E MPL ATE
Overlay and flush inset panels must be a minimum of 5/8"
(16) thick to support mounting the handle. Panel thickness
does not include backer and spacer panel. Mount handle
close to the opening edge of the door.
PRO 48
DEPTH OF TUBULAR
AND PRO HANDLES
2"
(51)
3"
I N T E G R AT E D
1"
(25)
(76)
11/4" (32) PANEL
1" (25) PANEL
3/4" (19) PANEL
.10" (3) SPACER PANEL
1/4" (6) BACKER PANEL
WINE
DOOR
Overlay and flush inset panel thickness.
|
35
UNDERCOUNTER
subzero.com/specs
B U I L T- I N
B UILT-IN R EF R IGE RATION
Overlay Application
F ULL-S CALE T E MPL ATE
237/8" (606)
TO REAR OF UNIT
OVERALL WIDTH OF UNIT
PRO 48
0" (0)
1/4" (6)
1/2" (13)
3/4" (19)
1" (25)
11/4" (32)
11/2" (38)
13/4" (44)
I N T E G R AT E D
2" (51)
21/4" (57)
21/2" (63)
23/4" (70)
3" (76)
31/4" (83)
31/2" (89)
WINE
1" (25) THICK
PANEL
3/4" (19) THICK
OVERLAY PANEL
(TYPICAL)
UNDERCOUNTER
1/4" (6) BACKER
PANEL
0"
1" (25)
SCALE
90° door opening (top view).
36
|
Sub-Zero Customer Care 800.222.7820
B UILT-IN R EF R IGE RATION
B U I L T- I N
Flush Inset Application
F ULL-S CALE T E MPL ATE
24" (610)
TO BACK WALL
For panels thicker than 3/4" (19), a 90° door stop may be
required to prevent interference with adjacent cabinets.
1 1/4" (32)
PRO 48
2 3/16" (56)
ASSUMES
3/4" (19)
FLUSH INSET
PANEL
THICKNESS
I N T E G R AT E D
WINE
1" (25) THICK
PANEL
3/4" (19) THICK
FLUSH INSET PANEL
(TYPICAL)
1/4" (6) BACKER
0"
1" (25)
SCALE
110° door opening (top view).
subzero.com/specs
|
37
UNDERCOUNTER
PANEL
B U I L T- I N
B UILT-IN R EF R IGE RATION
PRO 48
FILLER STRIP
11/4" (32)
WINE
I N T E G R AT E D
APPROX PROFILE OF
STAINLESS STEEL WRAPPED
DOOR AND HANDLE
Dual Standard Installation
F ULL-S CALE T E MPL ATE
UNDERCOUNTER
Typical framed, overlay or stainless steel dual installation
with filler strip at maximum 110° door opening. Panel thickness may require a 90° door stop.
0"
1" (25)
SCALE
Dual standard installation (top view).
38
|
Sub-Zero Customer Care 800.222.7820
DOOR
CLOSED
DOOR
OPEN 110°
B UILT-IN R EF R IGE RATION
B U I L T- I N
FILLER STRIP
PRO 48
1 1/2" (38)
1/2" (13)
WINE
Dual Flush Inset Installation
DOOR
CLOSED
I N T E G R AT E D
PROFILE OF 3/4" (19) FLUSH INSET PANEL
AND TUBULAR HANDLE
DOOR
OPEN 110°
F ULL-S CALE T E MPL ATE
Typical flush inset dual installation with filler strip at maximum 110° door opening. Panel thickness may require a 90°
door stop.
1" (25)
SCALE
Dual flush inset installation (top view).
subzero.com/specs
|
39
UNDERCOUNTER
0"
P RO 48 R EF R IGE RATION
B U I L T- I N
PRO 48 Refrigeration
P R O 4 8 MO D ELS
PRO 48
Freshness finds unmistakable expression in the Sub-Zero
PRO 48. An 800-pound monument to food preservation—
equal parts sculpted metal design statement and culinary
secret weapon. Its vast interior, like its bold exterior, is
crafted of stainless steel. The PRO 48 is available with
or without a glass door and may be either built in or
freestanding.
648PRO
648PROG
I N T E G R AT E D
WINE
|
41
UNDERCOUNTER
subzero.com/specs
B U I L T- I N
P RO 48 R EF R IGE RATION
Overall Dimensions
P RO 48
25 7/8" (657)
PRO 48
48" (1219)
84"
(2134)
42 1/8"
(1070)
30 1/2"
I N T E G R AT E D
(775)
4" (102)
HEIGHT DIMENSIONS ± 1/2" (13)
30 3/16" (767)
23 7/8"
(606)
14 1/2"
(368)
21"
(533)
30 3/4"
WINE
(781)
2 3/8" (60)
Model 648PRO, 648PROG.
SPECIFICATIONS
IN TERIOR C APAC ITY
648PRO
648PROG
UNDERCOUNTER
SH IPP IN G WEIGH T
648PRO
648PROG
42
|
Sub-Zero Customer Care 800.222.7820
R C U FT (L)
F CU FT (L)
18.4 (521)
18.4 (521)
11.7 (331)
11.7 (331)
LB ( K G )
860 (390)
875 (397)
P RO 48 R EF R IGE RATION
B U I L T- I N
Opening Dimensions
S TANDAR D | F LU SH INSTAL L ATION
D
OPENING
DEPTH
PRO 48
TOP VIEW
I N T E G R AT E D
W
H
OPENING WIDTH
OPENING
HEIGHT
SIDE VIEW
FRONT VIEW
WINE
OPENING DIMENSIONS
Standard
Flush
W
H
D
47 1/2" (1206)
48" (1219)
83 3/4" (2127)
84 1/8" (2137)
24" (610)
26" (660)
For standard built-in installations, the face frame of the unit
will extend 2" (51) beyond cabinetry. For flush installations,
the front of the face frame will be flush with surrounding
cabinetry.
|
43
UNDERCOUNTER
subzero.com/specs
B U I L T- I N
P RO 48 R EF R IGE RATION
Electrical
Plumbing
The electrical supply should be located within the shaded
area shown in the illustration below. A separate circuit, servicing only this appliance is required. A ground fault circuit
interrupter (GFCI) is not recommended and may cause interruption of operation.
The water supply line should be located within the shaded
area shown in the illustration below. The water supply line
should be connected to the house supply with an easily
accessible shut-off valve. Do not use self‑piercing valves.
The water supply line must not interfere with installation of
the anti-tip bracket.
PRO 48
Installation must comply with all applicable electrical codes.
ELECTRICAL REQUIREMENTS
Electrical Supply
115 VAC, 60 Hz
Service
15 amp
Receptacle
3-prong grounding-type
A reverse osmosis system can be used provided there is
constant water pressure of 35–120 psi (2.4–8.3 bar) supplied
to the unit at all times. A copper line is not recommended
for this application.
Installation must comply with all applicable plumbing codes.
PLUMBING REQUIREMENTS
1/4"
Water Supply
Pressure
7"
E
I N T E G R AT E D
(178)
35–120 psi (2.4–8.3 bar)
Excess Line for Connection
6"
(152)
75 1/2" (1918)
FROM FLOOR
RIGHT SIDE
OF OPENING
RIGHT SIDE
OF OPENING
Electrical supply location.
6"
(152)
5 3/16"
(132)
3" (76)
UNDERCOUNTER
WINE
AREA EXTENDS 1/2" (13)
FORWARD ON FLOOR
Water supply location.
44
|
Sub-Zero Customer Care 800.222.7820
OD copper, braided stainless
steel or PEX tubing
36" (914)
P RO 48 R EF R IGE RATION
B U I L T- I N
Standard Handles
Optional stainless steel tubular and pro handles are avail­
able through an authorized Sub-Zero dealer. For local dealer
information, visit the find a showroom section of our
website, subzero.com.
Refer to the chart below for standard handle lengths for
PRO 48 models.
TUBULAR
PRO
NA
27 11/16"
(703)
Refrigerator Drawer
NA
19 15/16"
(506)
Freezer Drawer
NA
Door
PRO 48
HANDLE LENGTH
11 9/16" (294)
I N T E G R AT E D
WINE
|
45
UNDERCOUNTER
subzero.com/specs
I N T EG R AT ED R E FRIGE RATION
B U I L T- I N
Integrated Refrigeration
With custom front panels and hardware, Sub-Zero invented
integrated columns, tall and drawer models that disappear
into the decor. Integrated units fit flush with other cabinets,
making integrated refrigeration as practical and beautiful in
the master suite, bar or theatre room as in the kitchen.
PRO 48
C OLUMN MO DEL S
IC-24R
IC-24FI
IC-30R(ID)
IC-30FI
I N T E G R AT E D
IC-18FI
IC-36R(ID)
IC-36FI
TALL MO DELS
WINE
IT-30R(ID)
IT-30FI
IT-30CI(ID)
IT-36R(ID)
IT-36CI(ID)
D RAWER MO DEL S
ID-27R
ID-30R(P)
ID-30F(I)
ID-30C(I)
ID-36R(P)
ID-36C(I)
subzero.com/specs
|
47
UNDERCOUNTER
ID-24R
ID-24F(I)
B U I L T- I N
I N T EG R AT ED R E FRIGE RATION
Specifications
INTERIOR CAPACITY— CU FT
PRO 48
CO L U M N
IC-18FI
IC-24R
IC-24FI
IC-30R(ID)
IC-30FI
IC-36R(ID)
IC-36FI
TA L L
C O LU MN
(L )
RE FR
FRZR
8.4 (238)
17.3 (490)
15.3 (433)
21.4 (606)
20.0 (566)
FRZR
16.5 (467)
10.6 (300)
20.5 (580)
13.3 (377)
DRAWE R
RE FR
ID-24R
ID-24F(I)
ID-27R
ID-30R(P)
ID-30F(I)
ID-30C(I)
ID-36R(P)
ID-36C(I)
4.0 (113)
69 1/2"
84"*
(2134)
(1765)
15.1 (428)
5.0 (142)
6.4 (181)
FRZR
3.8 (108)
4.6 (130)
5.2 (147)
3.0 (85)
6.6 (187)
3.4 (96)
CO L U M N
18" Column
24" Column
30" Column
36" Column
TA L L
WINE
24" (610)
4 1/2" (114)
12.3 (348)
4.9 (139)
2.0 (57)
2.5 (71)
3 5/8" (92)
*83 1/2" (2121) MIN TO 84 1/2" (2146) MAX
SHIPPING WEIGHT
UNDERCOUNTER
W
12.9 (365)
RE FR
IT-30R(ID)
IT-30FI
IT-30CI(ID)
IT-36R(ID)
IT-36CI(ID)
I N T E G R AT E D
Overall Dimensions
L B (KG )
260 (118)
340 (154)
400 (181)
440 (200)
A
13/4" (45)
L B (KG )
30" Tall
36" Tall
DRAWE R
24" Drawer
27" Drawer
30" Drawer
36" Drawer
400 (181)
460 (209)
L B (KG )
B
170 (77)
190 (86)
210 (95)
250 (113)
IMPORTANT NOTE: Overall dimensions do not include panels
COLUMN
W
A
B
or handles. Dimensions will vary with panel thickness.
18" Column
18" (457)
2 1/2" (64)
16 1/2" (419)
24" Column
24" (610)
4" (102)
22 1/2" (572)
30" Column
30" (762)
5 5/8" (143)
28 1/2" (724)
36" (914)
7 1/4"
34 1/2" (876)
36" Column
48
|
Sub-Zero Customer Care 800.222.7820
(184)
I N T EG R AT ED R E FRIGE RATION
B U I L T- I N
Overall Dimensions
TALL
D R AW ER
W
W
24" (610)
24" (610)
1/4" (6)
4 1/2" (114)
13 5/16"
(338)
(876)
3/8" (10)
10 9/16"
(268)
44 7/8"
84"*
(2134)
PRO 48
34 1/2"*
(1140)
3 5/8" (92)
*34" (864) MIN TO 35" (889) MAX
3/8" (10)
13 5/16"
(338)
I N T E G R AT E D
3/8" (10)
10 9/16"
(268)
18 3/8"
(467)
3 5/8" (92)
*83 1/2" (2121) MIN TO 84 1/2" (2146) MAX
DRAWER
A
13/4" (45)
(467)
TA LL
24" Drawer
24" (610)
27" Drawer
27" (686)
30" Drawer
30" (762)
36" Drawer
36" (914)
B
A
B
30" (762)
5 5/8" (143)
28 1/2" (724)
36" Tall
36" (914)
7 1/4" (184)
34 1/2" (876)
subzero.com/specs
|
49
UNDERCOUNTER
W
30" Tall
WINE
18 3/8"
W
B U I L T- I N
I N T EG R AT ED R E FRIGE RATION
Opening Dimensions
I N T EG R AT ED
OPENING DIMENSIONS
PRO 48
25" (635)
OPENING
DEPTH
H
18" (457)
24" (610)
30" (762)
36" (914)
84" (2134)
84" (2134)
84" (2134)
84" (2134)
24" Drawer
27" Drawer
30" Drawer
36" Drawer
W
H
24" (610)
27" (686)
30" (762)
36" (914)
34 1/2" (876)
34 1/2" (876)
34 1/2" (876)
34 1/2" (876)
The depth of each integrated model is 24" (610). Allow for
panel thickness when planning the finished opening depth.
A minimum 3 1/2" (89) finished return is required on all sides
of the opening. Framed cabinets will require additional
finished filler material behind the face frame for a proper
installation. Refer to the illustration.
I N T E G R AT E D
WINE
W
18" Column
24" Column
30" Column | Tall
36" Column | Tall
D RAWER
TOP VIEW
H
W
OPENING
HEIGHT
OPENING WIDTH
D U A L I N S TA LLATI O N
When installing two units side by side in a dual installation, the opening width is the width of the two units added
together. A dual installation kit will be required for this installation. If a dual installation kit is not specified, a minimum
2" (51) filler strip is required between units.
SIDE VIEW
FRONT VIEW
NOTE: 3 1/2" (89) finished returns will be visible and should be finished to match cabinetry.
3/4"
3 1/2" (89)
UNDERCOUNTER
C OL U MN | TA L L
(19)
TYPICAL
FINISHED
RETURN
W
W
FRAMELESS CABINETRY
50
|
3 1/2" (89)
FINISHED
RETURN
FILLER
FRAMED CABINETRY
Sub-Zero Customer Care 800.222.7820
Dual installation kits are available through an authorized
Sub-Zero dealer. For local dealer information, visit the find a
showroom section of our website, subzero.com. For questions regarding the installation, call Sub‑Zero customer care
at 800-222-7820.
I N T EG R AT ED R E FRIGE RATION
B U I L T- I N
Electrical
Plumbing
The electrical supply must be located within the shaded
area shown in the illustration and chart below. A separate
circuit, servicing only this appliance is required. A ground
fault circuit interrupter (GFCI) is not recommended and may
cause interruption of operation.
The water supply line should be located within the shaded
area shown in the illustration below. The water supply line
should be connected to the house supply with an easily
accessible shut-off valve. Do not use self‑piercing valves.
The water supply line must not interfere with installation of
the anti-tip bracket.
Installation must comply with all applicable electrical codes.
ELECTRICAL REQUIREMENTS
Electrical Supply
115 VAC, 60 Hz
Service
15 amp
Receptacle
3-prong grounding-type
ELECTRICAL SUPPLY LOCATION
A
6" (152)
24" Model
9 1/2" (241)
27" Model
11" (279)
30" Model
12 1/2" (318)
36" Model
15 1/2" (394)
Installation must comply with all applicable plumbing codes.
PLUMBING REQUIREMENTS
1/4"
Water Supply
Pressure
OD copper, braided stainless steel or PEX tubing
35–120 psi (2.4–8.3 bar)
Excess Line for Connection
36" (914)
WATER SUPPLY LOCATION
A
18" Model
3" (76)
24" Model
5 1/2" (140)
30" Model
6" (152)
36" Model
9" (229)
I N T E G R AT E D
18" Model
A reverse osmosis system can be used provided there is
constant water pressure of 35–120 psi (2.4–8.3 bar) supplied
to the unit at all times. A copper line is not recommended
for this application.
PRO 48
The electrical outlet must be positioned with the grounding
prong to the right of the thinner blades.
LEFT SIDE
OF OPENING
41/2"
(114)
RIGHT SIDE
OF OPENING
A
WINE
4 1/4"
(108)
1/4" (6)
FLOOR
A
6" (152)
3" (76)
Electrical supply location.
AREA EXTENDS 1/2" (13)
FORWARD ON FLOOR
Water supply location.
|
51
UNDERCOUNTER
subzero.com/specs
B U I L T- I N
I N T EG R AT ED R E FRIGE RATION
Custom Panels
PRO 48
For integrated models, custom door panels and handle
hardware must be provided. Refer to the panel requirements
chart and typical panel dimensions.
TY PI C AL PAN EL D I M EN S I O N S
The thickness of the custom panel can vary. A minimum
5/8" (16) thick panel is required, but the thickness can be
increased provided it does not exceed the weight limit. The
depth of each integrated model is 24" (610). Allow for panel
thickness when planning the finished opening depth. Refer
to the full-scale template on page 55.
79 7/8"
49 3/8"
(2029)
(1254)
13 9/16"
(345)
CAUTION
16 11/16"
As reveals between cabinetry and the unit decrease,
severe finger pinching can occur while door is closing.
(424)
I N T E G R AT E D
W
W
Finish all sides of custom panels. They will be visible when
the door/drawer is open.
Column
D-style handles are recommended. Door handles must be
located near the edge of the panel opposite the hinge and
should be centered top to bottom. Drawer handles must
be located near the top edge of each panel. Stainless steel
tubular and pro handles are avail­able through an authorized
Sub-Zero dealer. For local dealer information, visit the find a
showroom section of our website, subzero.com.
Typical panel dimensions are based on an 84" (2134) finished
height for column and tall models and 34 1/2" (876) for drawer
models, with a 4" (102) toe kick and 1/8" (3) reveals. Panel
dimensions must be adjusted accordingly for all other installations. Refer to the illustration for panel heights and the
chart below for panel widths.
W E I G H T P E R PA N E L
18" Column
24" Column
30" Column
36" Column
W E I G H T P E R PA N E L
30" Tall (door)
36" Tall (door)
Drawer
PA N E L T H I C K N E S S
All Panels
Tall
Drawer
PANEL WIDTH
PANEL REQUIREMENTS
WINE
W
MA X
45 lb (20 kg)
60 lb (27 kg)
75 lb (34 kg)
75 lb (34 kg)
W
18" Model
17 3/4"
24" Model
23 3/4" (603)
27" Model
26 3/4" (679)
30" Model
29 3/4" (756)
36" Model
35 3/4" (908)
MAX
50 lb (22 kg)
60 lb (27 kg)
15 lb (7 kg)
MIN
5/8"
(16)
D U A L I N S TA LLATI O N
For dual installations, refer to the illustration for panel
heights and the chart below for panel widths.
UNDERCOUNTER
PANEL WIDTH
52
|
Sub-Zero Customer Care 800.222.7820
(451)
W
18" Model
17 13/16"
24" Model
23 13/16" (605)
27" Model
26 13/16" (681)
30" Model
29 13/16" (757)
36" Model
35 13/16" (910)
(452)
I N T EG R AT ED R E FRIGE RATION
B U I L T- I N
Custom Panels
TO E K I C K C LEAR A N C E
The height of the custom door panel can extend beyond the
typical panel height, provided it does not exceed the weight
limit. Refer to the illustration below.
The height of the toe kick area can extend beyond the
typical toe kick height, provided it does not exceed the
dimensions in the illustration below. Toe kick heights from
2" (51) to 3 7/8" (98) require a reduced toe kick accessory
available through an authorized Sub-Zero dealer. For local
dealer information, visit the find a showroom section of our
website, subzero.com. For questions regarding the installation, call Sub‑Zero customer care at 800-222-7820.
1 3/4"
(45)
PRO 48
D OO R PANEL HEIGHT
A DECORATIVE VALANCE
CANNOT EXTEND
BEYOND THIS PLANE
1/8" (3)
DOOR
PANEL
84"
24" (610)
(2134)
TO BACK OF UNIT
HINGE**
VENTED
LOUVERS
I N T E G R AT E D
24" (610)
TO BACK OF UNIT
HINGE
DOOR
PANEL
1 1/8" (29)
MAX
TOE KICK
ADJUSTMENT
2" (51)*
TO
6" (152)
FROM
FLOOR
A DECORATIVE TOE KICK
CANNOT EXTEND
BEYOND THIS PLANE
Upper valance—column and tall (side view).
*2" (51) to 3 7/8" (98) requires sales accessory.
**Column models only.
WINE
Toe kick (side view).
|
53
UNDERCOUNTER
subzero.com/specs
B U I L T- I N
I N T EG R AT ED R E FRIGE RATION
Standard Handles
Optional stainless steel tubular and pro handles are avail­
able through an authorized Sub-Zero dealer. For local dealer
information, visit the find a showroom section of our
website, subzero.com.
HANDLE LENGTH
Column Door
TUBULAR
50 1/8"
(1273)
(1229)
Tall Door
24" Drawer
21 1/4" (540)
19 1/2" (495)
27" Drawer
24 1/4" (616)
22 1/2" (572)
30" Drawer
27 1/4" (692)
25 1/2" (648)
36" Drawer
33 1/4"
31 1/2" (800)
(845)
(845)
WINE
UNDERCOUNTER
PRO
48 3/8"
33 1/4"
I N T E G R AT E D
PRO 48
Refer to the chart below for standard handle lengths for
integrated models.
54
|
Sub-Zero Customer Care 800.222.7820
31 1/2"
(800)
I N T EG R AT ED R E FRIGE RATION
B U I L T- I N
Maximum Door Opening
F ULL-S CALE T E MPL ATE
As the panel width and/or depth increases, so does the
potential for panel interference. Interference may be
minimized by utilizing the 90° door stop.
PRO 48
3/4" (19) PANEL
DOOR OPEN
MAXIMUM 105°
POTENTIAL
INTERFERENCE
I N T E G R AT E D
1/8" (3) REVEAL
DOOR CLOSED
3/4" (19) PANEL
ADJACENT
CABINETRY
WINE
POTENTIAL INTERFERENCE
1" (25)
SCALE
Maximum door opening (top view).
subzero.com/specs
|
55
UNDERCOUNTER
0"
W INE S T O R AG E
B U I L T- I N
Wine Storage
Wine finds a well-deserved place of honor in a Sub-Zero
wine storage unit. Every detail is designed to ensure better
wine preservation. Cherrywood-faced racks, soft lighting,
custom cabinetry if desired—Sub-Zero helps make a wine
collection an element of beauty in the home.
PRO 48
W INE S T O R AG E MODE L S
424G
424FSG
UW-24FS
IW-24
IW-30
IW-30R
I N T E G R AT E D
UW-24
IW-18
WS-30
BW-30
WINE
|
57
UNDERCOUNTER
subzero.com/specs
B U I L T- I N
W INE S T O R AG E
Overall Dimensions
M ODEL 424G | UW-24
23 7/8" (606)
MO D EL 4 2 4 FS G | U W-2 4 FS
24 1/4" (616)
24" (610)
34 3/16"
PRO 48
34"
(864)
(868)
I N T E G R AT E D
4" (102)
4" (102)
25 3/8"
25 3/8"
(645)
(645)
1 3/4" (44)
1 3/4" (44)
SPECIFICATIONS
ST O R A G E C A PA C I TY
WINE
424G, UW-24
424FSG, UW-24FS
UNDERCOUNTER
BOTTL ES*
46
46
SH I P P I N G W E I G H T
L B (KG )
424G, UW-24
424FSG, UW-24FS
195 (88)
220 (100)
*750 ml bottles.
58
|
Sub-Zero Customer Care 800.222.7820
24 5/8" (625)
Overall dimensions for models 424G and UW-24 are
based on the stainless steel models. Refer to page 81 for
door clearance information. Freestanding models 424FSG
and UW-24FS have a finished stainless steel exterior and
handle.
W INE S T O R AG E
B U I L T- I N
Opening Dimensions
M ODEL 424G | UW-24
24" (610)
OPENING
DEPTH
PRO 48
TOP VIEW
34 1/2"
W
(876)
OPENING
HEIGHT
OPENING WIDTH
OPENING WIDTH
424G, UW-24
DUAL OPENING WIDTH
Two 24" Models
I N T E G R AT E D
SIDE VIEW
FRONT VIEW
W
24" (610)
W
48 1/8" (1222)
Dual installation kit required.
WINE
|
59
UNDERCOUNTER
subzero.com/specs
B U I L T- I N
W INE S T O R AG E
Overall Dimensions
C OLUMN
TALL
W
W
24" (610)
PRO 48
4 1/2" (114)
4 1/2" (114)
69 1/2"
84"*
(2134)
24" (610)
44 7/8"
84"*
(1765)
(2134)
(1140)
3/8" (10)
13 5/16"
(338)
I N T E G R AT E D
3/8" (10)
10 9/16"
(268)
3 5/8" (92)
*83 1/2" (2121) MIN TO 84 1/2" (2146) MAX
A
A
WINE
13/4" (45)
UNDERCOUNTER
13/4" (45)
17 3/4"
B
COLUMN
3 5/8" (92)
*83 1/2" (2121) MIN TO 84 1/2" (2146) MAX
(451)
W
A
B
IW-18
18" (457)
2 1/2" (64)
16 1/2" (419)
IW-24
24" (610)
4" (102)
22 1/2" (572)
IW-30
30" (762)
5 5/8" (143)
28 1/2" (724)
TALL
IW-30R
B
W
A
B
30" (762)
5 5/8" (143)
28 1/2" (724)
IMPORTANT NOTE: Overall dimensions do not include panels
or handles. Dimensions will vary with panel thickness.
60
|
Sub-Zero Customer Care 800.222.7820
W INE S T O R AG E
B U I L T- I N
Specifications
STORAGE CAPACITY
CO L U M N
BOTTL ES*
IW-18
IW-24
IW-30
TA L L
RE FR
BOTTL ES*
4.0 cu ft (113 L)
86
PRO 48
IW-30R
59
102
146
*750 ml bottles.
SHIPPING WEIGHT
CO L U M N
IW-18
IW-24
IW-30
TA L L
IW-30R
L B (KG )
350 (159)
410 (186)
460 (209)
L B (KG )
490 (222)
I N T E G R AT E D
WINE
|
61
UNDERCOUNTER
subzero.com/specs
B U I L T- I N
W INE S T O R AG E
Opening Dimensions
I N T EG R AT ED WINE STORAGE
OPENING DIMENSIONS
PRO 48
25" (635)
OPENING
DEPTH
TOP VIEW
W
H
18" Column
18" (457)
84" (2134)
24" Column
24" (610)
84" (2134)
30" Column | Tall
30" (762)
84" (2134)
The depth of each integrated (IW) model is 24" (610). Allow
for panel thickness when planning the finished opening
depth. A minimum 3 1/2" (89) finished return is required on all
sides of the opening. Framed cabinets will require additional
finished filler material behind the face frame for a proper
installation. Refer to the illustration.
I N T E G R AT E D
D U A L I N S TA LLATI O N
H
W
OPENING
HEIGHT
OPENING WIDTH
The unit can be installed next to an integrated refrigeration
model or another integrated wine storage model in a dual
installation. When installing two units side by side, the
opening width is the width of the two units added together.
A dual installation kit will be required for this installation. If a
dual installation kit is not specified, a minimum 2" (51) filler
strip is required between units.
Dual installation kits are available through an authorized
Sub-Zero dealer. For local dealer information, visit the find a
showroom section of our website, subzero.com. For questions regarding the installation, call Sub‑Zero customer care
at 800-222-7820.
WINE
SIDE VIEW
FRONT VIEW
NOTE: 3 1/2" (89) finished returns will be visible and should be finished to match cabinetry.
3/4"
UNDERCOUNTER
3 1/2" (89)
(19)
TYPICAL
FINISHED
RETURN
W
W
FRAMELESS CABINETRY
62
|
3 1/2" (89)
FINISHED
RETURN
FILLER
FRAMED CABINETRY
Sub-Zero Customer Care 800.222.7820
W INE S T O R AG E
B U I L T- I N
Overall Dimensions
M ODEL WS -30 | BW-30
SPECIFICATIONS
26 3/16" (665)
30" (762)
STORAGE C A PAC ITY
B OT T LE S *
WS-30
BW-30
SH IPP IN G WEIGH T
LB ( K G )
445 (202)
445 (202)
*750 ml bottles.
84"
(2134)
PRO 48
WS-30
BW-30
147
146
73 3/4"
(1873)
4" (102)
I N T E G R AT E D
HEIGHT DIMENSIONS ± 1/2" (13)
23 7/8" (606)
23 7/8"
(606)
17"
(432)
311/4"
(796)
WINE
2 3/8" (60)
Overall dimensions are based on the stainless steel model.
For flush inset applications, add 1/2" (13) to door clearance
dimensions.
|
63
UNDERCOUNTER
subzero.com/specs
B U I L T- I N
W INE S T O R AG E
Opening Dimensions
M ODEL WS -30 | BW-30 STANDARD INSTAL LATI O N
PRO 48
24" (610)
OPENING
DEPTH
I N T E G R AT E D
TOP VIEW
83 3/4"
(2127)
OPENING
HEIGHT
SIDE VIEW
WINE
W
OPENING WIDTH
FRONT VIEW
NOTE: Shaded line represents profile of unit.
OPENING WIDTH
W
WS-30
29 1/2" (749)
BW-30
29 1/2" (749)
If an 83" (2108) grille height is specified, the opening height
must be decreased by 7/8" (22). If an 88" (2235) grille height is
specified, the opening height must be increased by 4" (102).
UNDERCOUNTER
If two units are installed side by side, refer to page 66 for
dual standard installations.
64
|
Sub-Zero Customer Care 800.222.7820
W INE S T O R AG E
B U I L T- I N
Opening Dimensions
M ODEL WS -30 | BW-30 FL USH INSE T INSTA LLATI O N
26 3/16"
(665)
FLUSH
INSET
DEPTH
2 3/16"
(56)
PRO 48
FINISHED
CLEATS*
TOP VIEW
11/4"
1/4"
(6)
(32)
I N T E G R AT E D
W
84"
(2134)
FLUSH
INSET
HEIGHT
FLUSH INSET WIDTH
11/4"
(32)
4" (102)
3"
(76)*
TYPICAL
SIDE VIEW
2 3/16"
(56)
FRONT VIEW
WINE
*3" (76) typical depth. Shaded areas will be visible and should be finished to match cabinetry.
NOTE: Shaded line represents profile of unit with 3/4" (19) panel.
FLUSH INSET WIDTH
W
WS-30
32" (813)
BW-30
32" (813)
Dimensions assume a 3/4" (19) panel thickness.
If an 83" (2108) grille height is specified, the flush inset height
must be decreased by 7/8" (22). If an 88" (2235) grille height
is specified, the flush inset height must be increased by 4"
(102).
subzero.com/specs
|
65
UNDERCOUNTER
If two units are installed side by side, refer to page 67 for
dual flush inset installations.
B U I L T- I N
W INE S T O R AG E
Opening Dimensions
M ODEL WS -30 | BW-30 DUAL STANDARD IN S TALLATI O N
PRO 48
24" (610)
OPENING
DEPTH
I N T E G R AT E D
TOP VIEW
(2127)
OPENING
HEIGHT
WINE
SIDE VIEW
OPENING WIDTH
FRONT VIEW
NOTE: Shaded line represents profile of unit.
DUAL OPENING WIDTH
UNDERCOUNTER
W
83 3/4"
W
WS-30 and 30" Built-In Model
59 3/4" (1518)
BW-30 and 30" Built-In Model
59 3/4" (1518)
WS-30 and 36" Built-In Model
65 3/4" (1670)
BW-30 and 36" Built-In Model
65 3/4" (1670)
66
|
Sub-Zero Customer Care 800.222.7820
A dual installation kit will be required for this installation.
W INE S T O R AG E
B U I L T- I N
Opening Dimensions
M ODEL WS -30 | BW-30 DUAL FL USH INSE T I N S TA LLATI O N
26 3/16"
(665)
FLUSH
INSET
DEPTH
2 3/16"
(56)
PRO 48
FINISHED
CLEATS*
TOP VIEW
11/4"
1/4"
(6)
(32)
I N T E G R AT E D
W
84"
(2134)
FLUSH
INSET
HEIGHT
FLUSH INSET WIDTH
11/4"
(32)
4" (102)
3"
(76)*
TYPICAL
SIDE VIEW
2 3/16"
(56)
FRONT VIEW
WINE
*3" (76) typical depth. Shaded areas will be visible and should be finished to match cabinetry.
NOTE: Shaded line represents profile of unit with 3/4" (19) panel.
DUAL FLUSH INSET WIDTH
W
WS-30 and 30" Built-In Model
62 1/4" (1581)
BW-30 and 30" Built-In Model
62 1/4" (1581)
WS-30 and 36" Built-In Model
68 1/4" (1734)
BW-30 and 36" Built-In Model
68 1/4" (1734)
Dimensions assume a 3/4" (19) panel thickness. A dual installation kit will be required for this installation.
|
67
UNDERCOUNTER
subzero.com/specs
B U I L T- I N
W INE S T O R AG E
Electrical
PRO 48
The electrical supply must be located within the shaded
area shown in the illustration for your specific model. For
integrated (IW) models, also refer to the chart. A separate
circuit, servicing only this appliance is required. A ground
fault circuit interrupter (GFCI) is not recommended and may
cause interruption of operation.
ELECTRICAL LOCATION—INTEGRATED
18" Model
6" (152)
24" Model
9 1/2" (241)
30" Model
12 1/2" (318)
If the unit will be connected to a home security system,
allow 36" (914) of excess wiring for proper connection.
IMPORTANT NOTE: For integrated (IW) models, the electrical
outlet must be positioned with the grounding prong to the
right of the thinner blades.
Installation must comply with all applicable electrical codes.
LEFT SIDE
OF OPENING
41/2"
(114)
A
4 1/4"
ELECTRICAL REQUIREMENTS
(108)
Electrical Supply
115 VAC, 60 Hz
I N T E G R AT E D
Service
15 amp
Receptacle
Integrated models.
7"
E
(178)
6"
(152)
2"
(51)
15 1/2"
(394)
3" (76)
75 1/2" (1918)
FROM FLOOR
WINE
FLOOR
UNDERCOUNTER
1/4" (6)
FLOOR
3-prong grounding-type
LEFT SIDE
OF OPENING
Model 424G, UW-24.
68
|
RIGHT SIDE
OF OPENING
Model WS-30, BW-30.
Sub-Zero Customer Care 800.222.7820
A
W INE S T O R AG E
B U I L T- I N
Custom Panels
Custom Panel—424G | UW-24
For framed, overlay, integrated and flush inset applications,
a custom door panel must be provided. Handle hardware
must also be provided for overlay, integrated and flush
inset applications. Refer to panel requirements and custom
panel dimensions charts for your specific model and design
application.
For models 424G and UW-24, the custom door panel will
attach directly to the door frame with screws through a
series of pre-drilled holes.
Do not install a solid panel on a glass door unit. A solid door
is available as a sales accessory (except models WS-30 and
BW-30) and must be installed if a solid panel is being specified. Service may be required to install the door. Contact an
authorized Sub-Zero dealer for more information. Overall
dimensions are the same for glass and solid door panels.
WEIGH T PER PAN EL
MAX
424G, UW-24
10 lb (5 kg)
PAN EL TH IC KN ESS
M IN
5/8"
424G, UW-24
(16)
O V ER LAY PAN EL D I M EN S I O N S
A
A
A
H
I N T E G R AT E D
Models 424FSG and UW-24FS have a finished stainless
steel exterior that is designed to be used in a freestanding
application.
PANEL REQUIREMENTS
PRO 48
Finish all sides of the custom panels. They may be visible
when the door is open or through the window of glass door
models.
Refer to the charts for panel requirements and dimensions.
A
W
424G, UW-24
PANEL DIMENSIONS
PAN EL
424G, UW-24
W
H
23 3/4" (603)
30 1/16" (764)
STIL ES | RAIL S
Minimum
A
2 1/4" (57)
DOOR CLEARANCE
|
69
UNDERCOUNTER
subzero.com/specs
WINE
Models 424G and UW-24 can be installed flush with surrounding cabinetry. Depending on the thickness of the
overlay door panel, it may be necessary to install the unit
1/4" (6) beyond the front surface of adjacent cabinetry to
prevent interference when the door is opened to 145°. Refer
to the full-scale template on page 81.
B U I L T- I N
W INE S T O R AG E
Custom Panel—Integrated
For integrated (IW) models, a custom door panel and handle
hardware must be provided. Refer to the panel requirements
chart and typical panel dimensions.
PRO 48
Do not install a solid panel on the glass door unit. A solid
door is available as a sales accessory through an authorized
Sub-Zero dealer.
The thickness of the custom panel can vary. A minimum
5/8" (16) thick panel is required, but the thickness can be
increased provided it does not exceed the weight limit. The
depth of each integrated model is 24" (610). Allow for panel
thickness when planning the finished opening depth. Refer
to the full-scale template on page 55.
Finish all sides of custom panels. They will be visible when
the door/drawer is open.
W E I G H T P E R PA N E L
Door Frame (column)
Door Frame (tall)
Drawer Panel (tall)
PA N E L T H I C K N E S S
All Panels
UNDERCOUNTER
WINE
I N T E G R AT E D
PANEL REQUIREMENTS
70
|
Sub-Zero Customer Care 800.222.7820
MA X
35 lb (16 kg)
25 lb (11 kg)
15 lb (7 kg)
MIN
5/8"
(16)
CAUTION
As reveals between cabinetry and the unit decrease,
severe finger pinching can occur while door is closing.
D-style handles are recommended. Door handles must be
located near the edge of the panel opposite the hinge and
should be centered top to bottom. Drawer handles must
be located near the top edge of each panel. Stainless steel
tubular and pro handles are avail­able through an authorized
Sub-Zero dealer. For local dealer information, visit the find a
showroom section of our website, subzero.com.
W INE S T O R AG E
B U I L T- I N
Custom Panel—Integrated
D U AL I N S TALLATI O N
T Y PICAL PANEL DIME NSIONS
For dual installations, refer to the illustration for panel height
and the chart below for panel width.
PANEL WIDTH
79 7/8"
49 3/8"
MOD EL
(1254)
18" Model
24" Model
30" Model
W
17 13/16" (452)
23 13/16" (605)
29 13/16" (757)
13 9/16"
PRO 48
(2029)
(345)
16 11/16"
(424)
W
Column
W
Tall
I N T E G R AT E D
Typical panel dimensions are based on an 84" (2134) finished
height, 4" (102) toe kick and 1/8" (3) reveals. Panel dimensions must be adjusted accordingly for all other installations.
Refer to the illustration for panel height and the chart below
for panel width.
PANEL WIDTH
MODEL
18" Model
24" Model
30" Model
ST I L E S | R A I L S
MIN
3 1/4" (83)
7 3/4" (197)
9 1/2" (241)
4 1/2" (114)
WINE
Stiles
Top Rail
Bottom Rail (column)
Bottom Rail (tall)
W
17 3/4" (451)
23 3/4" (603)
29 3/4" (756)
|
71
UNDERCOUNTER
subzero.com/specs
B U I L T- I N
W INE S T O R AG E
Custom Panel—Integrated
TO E K I C K C LEAR A N C E
The height of the custom door panel can extend beyond the
typical panel height, provided it does not exceed the weight
limit. Refer to the illustration below.
The height of the toe kick area can extend beyond the
typical toe kick height, provided it does not exceed the
dimensions in the illustration below. Toe kick heights from
2" (51) to 3 7/8" (98) require a reduced toe kick accessory
available through an authorized Sub-Zero dealer. For local
dealer information, visit the find a showroom section of our
website, subzero.com. For questions regarding the installation, call Sub‑Zero customer care at 800-222-7820.
PRO 48
D OO R PANEL HEIGHT
1 3/4"
(45)
A DECORATIVE VALANCE
CANNOT EXTEND
BEYOND THIS PLANE
1/8" (3)
DOOR
PANEL
84"
24" (610)
(2134)
TO BACK OF UNIT
HINGE**
24" (610)
TO BACK OF UNIT
I N T E G R AT E D
HINGE
DOOR
PANEL
1 1/8" (29)
MAX
TOE KICK
ADJUSTMENT
2" (51)*
TO
6" (152)
FROM
FLOOR
Upper valance (side view).
*2" (51) to 3 7/8" (98) requires sales accessory.
**Column models only.
Toe kick (side view).
WINE
UNDERCOUNTER
VENTED
LOUVERS
72
|
Sub-Zero Customer Care 800.222.7820
A DECORATIVE TOE KICK
CANNOT EXTEND
BEYOND THIS PLANE
W INE S T O R AG E
B U I L T- I N
Custom Panel—WS-30 | BW-30
F R AMED
FR AM ED PAN EL D I M EN S I O N S
The framed application is an overlay model with framed
design features. It is not a separate model.
H
A
1/4"
Routing, recessing and optional extended handles may be
required for finger clearance. Refer to the full-scale template
on page 82.
A
A
H
PRO 48
(6), a filler material
If the custom panel is thinner than
must be added to achieve a proper fit. If the panel is thicker
than 1/4" (6), rout an edge around the panel or mount the
custom panel on a sheet of 1/4" (6) thick material and insert
into the channel.
A
W
PANEL REQUIREMENTS
W E I G H T P E R PA N E L
Door
Grille (optional)
Framed
75 lb (34 kg)
13 lb (6 kg)
MIN
1/4"
(6)
WS-30, BW-30
PANEL DIMENSIONS
FRAMED PAN EL
Door
Grille (optional)
W
H
29 3/4" (756)
29 3/4" (756)
69 9/16" (1767)
8 15/16" (227)
STIL ES | RAIL S
Minimum
A
3 3/16" (81)
I N T E G R AT E D
PA N E L T H I C K N E S S
MA X
WINE
|
73
UNDERCOUNTER
subzero.com/specs
B U I L T- I N
W INE S T O R AG E
Custom Panel—WS-30 | BW-30
O VER LAY
O VER LAY PA N EL D I MEN S I O N S
Overlay panels are typically created by combining a 3/4" (19)
custom panel, a .10" (3) spacer panel and a 1/4" (6) backer
panel. Refer to the illustrations below.
PRO 48
PANEL REQUIREMENTS
W E I G H T P E R PA N E L
MA X
Door
Grille
H
A
A
A
H
75 lb (34 kg)
13 lb (6 kg)
PA N E L T H I C K N E S S
MIN
5/8"
Overlay
(16)
A
W
CUSTOM
PANEL
SPACER PANEL
SPACER
PANEL
WS-30, BW-30
OVERLAY PANELS
CUSTOM PANEL
I N T E G R AT E D
D OOR
BACKER PANEL
BACKER
PANEL
TRIM
DOOR FRAME
GLASS
Overlay Panel
Spacer Panel
Backer Panel
GRIL L E
5/16" (8) min
1/8"
(3)
3/4"
(19)
typical
.10" (3) 1/4" (6)
Panel assembly (cross section). Panel assembly (rear view).
Overlay Panel
Spacer Panel
Backer Panel
W
H
30" (762)
29 1/8" (740)
29 3/4" (756)
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
W
H
30" (762)
29 1/8" (740)
29 3/4" (756)
9 1/4" (235)*
8 5/16" (211)
8 15/16" (227)
STIL ES | RAIL S
Minimum
A
3 1/4" (83)
*Panel height may be increased by 7/16" (11) to hide upper main frame. Also
refer to built-in panel configurator at subzero.com/trade/panels.
UNDERCOUNTER
WINE
Grille panel dimensions are for standard 84" (2134) overall unit height. For 83"
(2108) height, subtract 1" (25) from grille panel height dimensions and for 88"
(2235) height, add 4" (102). A specific panel grille must be ordered for an 83"
or 88" overall unit height.
74
|
Sub-Zero Customer Care 800.222.7820
W INE S T O R AG E
B U I L T- I N
Custom Panel—WS-30 | BW-30
F LUS H INS ET
FLU S H I N S ET PA N EL D I MEN S I O N S
The flush inset application is an overlay model with flush
inset panels. It is not a separate model.
H
A
A
For flush inset panels thicker than 3/4" (19), a 90° door stop
may be required to prevent interference with adjacent cabinets. Refer to the full-scale template on page 85.
PANEL REQUIREMENTS
W E I G H T P E R PA N E L
Door
Grille
Flush Inset
H
A
W
WS-30, BW-30
MA X
75 lb (34 kg)
13 lb (6 kg)
MIN
5/8"
(16)
FLUSH INSET PANELS
D OOR
Flush Inset Panel
Spacer Panel
Backer Panel
GRIL L E
Flush Inset Panel
Spacer Panel
Backer Panel
W
H
31" (787)
29 1/8" (740)
29 3/4" (756)
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
W
H
31" (787)
29 1/8" (740)
29 3/4" (756)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
STIL ES | RAIL S
Minimum
I N T E G R AT E D
PA N E L T H I C K N E S S
A
PRO 48
The flush inset design allows custom panels to be installed
flush with adjacent cabinets. Similar to overlay, flush inset
panels are typically created by combining a 3/4" (19) custom
panel, a .10" (3) spacer panel and a 1/4" (6) backer panel.
Refer to the illustrations for overlay panels on the previous
page.
A
3 3/4" (95)
Grille panel dimensions are for standard 84" (2134) overall unit height. For
83" (2108) height, subtract 1" (25) from grille panel height dimensions and for
88" (2235) height, add 4" (102). A specific panel grille must be ordered for an
83" or 88" overall unit height.
WINE
|
75
UNDERCOUNTER
subzero.com/specs
5/16" (8)
B U I L T- I N
W INE S T O R AG E
5/8"
(16)
TOP VIEW
TOP VIEW
CABINETRY
DOOR / DRAWER / GRILLE
1/2" (13)
BACKER
1/8"
5/16" (3)
(8)
CABINETRY
GRILLE
The illustrations provide
offsets and reveals for model
FLUSHpanel
INSET PANEL
WS-30 or BW-30 in a flush
inset
application. Refer to the
5/16" (8)
1/2"
chart below for reference to the illustrations.
(13)
5/8"
(16)
PRO 48
PANEL OFFSET
DOOR
DOOR
DOOR
1/8" (3)
BACKER
Grille Top
B
Grille Bottom | Door Top
C
Door Bottom
D
REVEAL
DOOR
GRILLE
5/16" (8)
5/8"
(16)
5/16" (8)
1/2"
(13)
1/8" (3)
1/4" (6)
SIDE VIEW
REVEAL
Illus. B
DOOR /
DRAWER
5/16"
(8) 3/32" GRILLE
(2)
1/2" (13)
5/16"
(8) 5/32"
(4)
DOOR
I N T E G R AT E D
DOOR
1
/16" (3)
(8)
/8"
SIDE
5 VIEW
FLUSH INSET PANEL
CABINETRY
1/8"
5/16" (3)
(8)
5/8" (16)
SIDE VIEW
1/2" (13)
3/32"
5/16" (2)
(8)
1/8"
5SIDE
/16" (3)
VIEW
(8)
5/32" DOOR
5/16" (4)
(8)
SIDE VIEWGRILLE
5/16"
(8)
1/2" (13)
CABINETRY
DRAWER
Illus. C
5/16"
(8) 5/32"
(4)
5/16"
GRILLE
(8) 3/32
"
(2)
DOOR
SIDE VIEW
Illus.
D
DRAWER
SIDE VIEW
WINE
3/32" 1/2" (13)
5/16" (2)
(8)
CABINETRY
1/4" (6)
Illus. A
GRILLE
TOP VIEW
CABINETRY
5/16" (8)
IL L U S
A
1/2" (13)
TOP VIEW
DOOR / DRAWER / GRILLE
SIDE SPACER
VIEW
Door | Grille Sides
5/16"
(8) 5/32"
(4)
GRILLE
Custom Panel—WS-30 | BW-30
F LUS H INS ET PA SPACER
NE L OFFSE T
1/2"
(13)
3/32"
(2)
5/8" (16)
1/2
DOOR
3/32"
5/16" (2)
(8)
5/32"
5/16" (4)
(8)
SIDE VIEW
SIDE VIEW
DOOR /
DRAWER
5/16"
(8) 3/32"
(2)
DOOR
5/8" (16)
DRAWER
5/32"
5/16" (4)
(8)
5/16"
(8)
5/16"
(8) 3/32"
(2)
DOOR
SIDE VIEW
UNDERCOUNTER
DOOR /
DRAWER
SIDE VIEW
DRAWER
3/32"
5/8"(2)
(16)
5/16"
(8)
5/32"
5/16" (4)
(8)
3
SIDE VIEW
76
|
Sub-Zero Customer Care 800.222.7820
SIDE VIEW
W INE S T O R AG E
B U I L T- I N
Custom Panel—WS-30 | BW-30
D U AL FLU S H I N S ET PA N EL D I MEN S I O N S
D U AL INS TALLATIONS
Dual installation kits are available through an authorized
Sub-Zero dealer. For local dealer information, visit the find a
showroom section of our website, subzero.com. For questions regarding the installation, call Sub‑Zero customer care
at 800-222-7820.
A
A
A
H
A
W
WS-30, BW-30
DUAL FLUSH INSET PANELS
D OOR
Flush Inset Panel
Spacer Panel
Backer Panel
GRIL L E
Flush Inset Panel
Spacer Panel
Backer Panel
W
H
30 1/2" (775)
29 1/8" (740)
29 3/4" (756)
69 3/4" (1772)
68 15/16" (1751)
69 9/16" (1767)
W
H
30 1/2" (775)
29 1/8" (740)
29 3/4" (756)
9 1/4" (235)
8 5/16" (211)
8 15/16" (227)
STIL ES | RAIL S
Minimum
I N T E G R AT E D
For dual standard installations, panel dimensions are the
same as for single installations. Refer to the chart on page
74. Panel dimensions and offsets for dual flush inset installations are listed on the following pages.
H
PRO 48
A dual installation kit may be required if two models WS-30
or a model WS-30 and built-in unit are installed side by side,
or two models BW-30 or a model BW-30 and built-in unit.
Installations without a custom filler strip require a dual installation kit. If a dual installation kit is not specified, a 2" (51)
filler strip is recommended between units. Dual installations
without a filler strip can only be accomplished using two
units with opposite hinges. Refer to the illustrations below.
A
3 3/4" (95)
Grille panel dimensions are for standard 84" (2134) overall unit height. For
83" (2108) height, subtract 1" (25) from grille panel height dimensions and for
88" (2235) height, add 4" (102). A specific panel grille must be ordered for an
83" or 88" overall unit height.
WITHOUT FILLER STRIP
WINE
Opposite hinges.
FILLER STRIP
Same side hinges.
|
77
UNDERCOUNTER
subzero.com/specs
W INE S T O R AG E
TOP VIEW
TOP VIEW
B U I L T- I N
DOOR / DRAWER / GRILLE
BACKER
SPACER
DOOR
CABINETRY
TOP VIEW
5/16" (8)
Custom Panel—WS-30
| BW-30
1/2"
5/8"
(13)
D U AL F LUS H IN SE T PANE L OFFSE
T
(16)
1/8" (3)
BACKER
SPACER
BACKER
CABINETRY
SPACER
IL L U S
Door (hinge) | Grille Sides
A
Door (handle) Sides
B
Grille Top
CABINETRY
CABINETRY
TOP VIEWREVEAL
BACKER
GRILLE
1/8"
5/16" (3)
(8)
E
5/8"
(16)
5/16" (8)
5/8"
(16)
GRILLE
Illus. A
CABINETRY
I N T E G R AT E D
GRILLE
TOP VIEW
5/16" (8)
5/16" (8)
DOOR
1/8" (3)
DOOR
DOOR
1
/8" (3)
DOOR
1/4" (6)
1/4" (6)
REVEAL
REVEAL
FLUSH INSET PANEL
1/8"
5/16" (3)GRILLE
(8)
CABINETRY
1/2"
(13)
5/16" (8)
5/16" (8)
1/8" (3)
1/8" (3)
1/4" (6)
1/4" (6)
REVEAL
REVEAL
5/16"
(8) 5/32"
(4)
Illus. B
1/2" (13)
CABINETRY
1/2" (13)
DOOR
SIDE VIEW
1/2"
(13)
CABINETRY
5/8"
SPACER
(16)
DOOR
DUAL
TRIM
5/16" (8)
1/2"
(13)
DOOR
DOOR
TOP VIEW
DOOR / DRAWER / GRILLE
FLUSH INSET PANEL
D
1/2" (13)
Door Bottom
DOOR
1/4" (6)
C
Grille Bottom | Door Top
TOP VIEW
DOOR / DRAWER / GRILLE
5/16" (8)
The illustrations provide panel offsets and reveals for
model
FLUSH
INSET PANEL
WS-30 or BW-30 in a dual flush inset application. Refer to
5/16" (8)
the chart below for reference to the illustrations.
PANEL OFFSET
TOP VIEW
TOP VIEW
DOOR / DRAWER / GRILLE
FLUSH INSET PANEL
PRO 48
DOOR
1
3/32" /2" (13)
5/16" (2)
(8)
1/8"
5/16VIEW
SIDE
" (3)
(8)
1/2" (13)
GRILLE
SIDE VIEW
5/16"
(8) 5/32"
(4)
1/2" (13)
DOOR
1/2
5/16"
32""
(8) 53//32
5/16" (4)
(2)
(8)
DOOR
3/32
GRILLE
"
5/16" (2)
(8)
1/8"
5/16
" (3)
SIDE
VIEW
(8)
Illus. C
DOOR /
DRAWER
5/16"
(8) 5/32GRILLE
"
(4)
GRILLE
SIDE VIEW
SIDE VIEW
1/2
DOOR
Illus. D
3/32"
5/16" (2)
(8)
SIDE VIEW
SIDE VIEW
5/16"
(8) 3/32"
(2)
DOOR
WINE
5/8" (16)
DRAWER
5/32"
5/16" (4)
(8)
5/16"
(8)
5/16"
(8) 3/32"
(2)
DOOR
DRAWER
5/DRAWER
Illus.
32E
"
5/16" (4)
(8) DOOR
SIDE VIEW
UNDERCOUNTER
DOOR /
DRAWER
DOOR
5/8" (16)SIDE VIEW
SIDE VIEW
DOOR /
DRAWER
5/16"
(8) 3/32"
(2)
DRAWER
3/32"
5(2)
/8" (16)
5/16"
DOOR /
(8) DRAWER
5/16"
(8)
5/16"
(8) 35//32
32""
5/16" (2)
(4)
(8)
5/8" (16)
SIDE VIEW
SIDE VIEW
3/32"
(2)
3
SIDE VIEW
5/16"
(8)
5/32"
5/16" (4)
(8)
3
SIDE VIEW
78
|
Sub-Zero Customer Care 800.222.7820
SIDE VIEW
W INE S T O R AG E
B U I L T- I N
Custom Panel—WS-30 | BW-30
Standard Handles
S I DE PANEL
Optional stainless steel tubular and pro handles are avail­
able through an authorized Sub-Zero dealer. For local dealer
information, visit the find a showroom section of our
website, subzero.com.
The custom side panel must be a minimum of 24" (610) deep
and 1/2" (13) thick. Routing will be necessary for the side
panel to fit flush against the side of the unit. Refer to the
illustrations below.
HANDLE LENGTH
TU BU L A R
424G, UW-24 Door
24 1/4"
IW-18, IW-24, IW-30 Door
FRONT
OF SIDE
PANEL
(616)
(1273)
48 3/8"
(572)
(1229)
IW-30R Door
33 1/4" (845)
31 1/2" (800)
IW-30R Drawer
24 1/4" (616)
22 1/2" (572)
63 7/8" (1622)
45 3/16" (1147)
WS-30, BW-30 Door
24" (610)
50 1/8"
PRO
22 1/4"
1" (25)
1/8" (3)
1/2" (13)
1 7/8"(48)
1" (25)
I N T E G R AT E D
1 7/8" (48)
ROUT TO 1/8" (3)
84"
PRO 48
When installing model WS-30 or BW-30 with a custom side
panel, an accessory kit is required. Stainless steel and white
enamel side panels are available through an authorized
Sub-Zero dealer. For local dealer information, visit the find a
showroom section of our website, subzero.com.
Refer to the chart below for standard handle lengths for
wine storage models.
MAIN
FRAME
SIDE PANEL
ROUTING
(2134)
Routing detail.
WINE
4" (102)
OPTIONAL
TOE KICK
CUT-OUT
2 5/8"
(67)
Side panel dimensions.
|
79
UNDERCOUNTER
subzero.com/specs
B U I L T- I N
W INE S T O R AG E
Wine Rack Wood Facing
F ULL-S CALE T E MPL ATE
WOOD FACING WIDTH
PRO 48
The natural cherrywood facing on wine storage racks can
be stained and sealed, or replaced with wood more complementary to surrounding cabinetry. Refer to the full-scale
template below for profile dimensions of the wood facing
and the chart for width.
1/2"
5/8"
(13)
(16)
7/64" (3)
1/4"
(6)
27/32"
7/64"
(3)
I N T E G R AT E D
(21)
11/2"
(38)
27/32"
(21)
7/32" (6)
23/64"
23/64"
(9)
9/16"
(14)
(9)
5/64"
(2)
IW-18, IW-24,
IW-30, IW-30R
9/16"
(14)
WINE
UNDERCOUNTER
|
(2)
424G, UW-24,
424FSG, UW-24FS, WS-30
Wine rack wood facing profile.
80
5/64"
Sub-Zero Customer Care 800.222.7820
W
424G, UW-24
19 1/2"
424FSG, UW-24FS
19 1/2" (495)
IW-18
11 5/8" (295)
IW-24
17 5/8" (448)
IW-30, IW-30R
23 5/8" (600)
WS-30, BW-30
24 9/16" (624)
(495)
W INE S T O R AG E
B U I L T- I N
Door Clearance—424G | UW-24
F ULL-S CALE T E MPL ATE
To allow for a 145° door opening, the unit should extend
a minimum of 1/4" (6) beyond the front surface of adjacent cabinetry. The unit can be installed flush, however,
there is potential for interference with the panel if the
door is opened past 90°.
PRO 48
UNDERCOUNTER
UNIT
ADJACENT
CABINETRY
I N T E G R AT E D
DOOR CLOSED
1/2"
(13)
3/4" (19) DOOR PANEL
1/4" (6)
1/8" (3)
WINE
HINGE AT 145°
OPENING
(DOOR OPENS PAST 145°)
1" (25)
SCALE
145° door opening (top view).
subzero.com/specs
|
81
UNDERCOUNTER
0"
B U I L T- I N
W INE S T O R AG E
Framed Panel—WS-30 | BW-30
PRO 48
F ULL-S CALE T E MPL ATE
OPTIONAL EXTENDED
FULL-LENGTH HANDLE
I N T E G R AT E D
STANDARD
FULL-LENGTH HANDLE
2"
1"
(51)
(25)
3"
(76)
11/4" (32) PANEL
1" (25) PANEL
3/4" (19) PANEL
1/2" (13) PANEL
WINE
1/4" (6) FRAMED PANEL
DOOR
UNDERCOUNTER
Framed panel thickness.
82
|
Sub-Zero Customer Care 800.222.7820
W INE S T O R AG E
B U I L T- I N
Overlay | Flush Inset Panels—WS-30 | BW-30
F ULL-S CALE T E MPL ATE
Overlay and flush inset panels must be a minimum of 5/8"
(16) thick to support mounting the handle. Panel thickness
does not include backer and spacer panel. Mount handle
close to the opening edge of the door.
PRO 48
DEPTH OF TUBULAR
AND PRO HANDLES
2"
(51)
3"
I N T E G R AT E D
1"
(25)
(76)
11/4" (32) PANEL
1" (25) PANEL
3/4" (19) PANEL
.10" (3) SPACER PANEL
1/4" (6) BACKER PANEL
WINE
DOOR
Overlay and flush inset panel thickness.
|
83
UNDERCOUNTER
subzero.com/specs
B U I L T- I N
W INE S T O R AG E
Overlay Application—WS-30 | BW-30
F ULL-S CALE T E MPL ATE
237/8" (606)
TO REAR OF UNIT
OVERALL WIDTH OF UNIT
PRO 48
0" (0)
1/4" (6)
1/2" (13)
3/4" (19)
1" (25)
11/4" (32)
11/2" (38)
13/4" (44)
I N T E G R AT E D
2" (51)
21/4" (57)
21/2" (63)
23/4" (70)
3" (76)
31/4" (83)
31/2" (89)
WINE
1" (25) THICK
PANEL
3/4" (19) THICK
OVERLAY PANEL
(TYPICAL)
UNDERCOUNTER
1/4" (6) BACKER
PANEL
0"
1" (25)
SCALE
90° door opening (top view).
84
|
Sub-Zero Customer Care 800.222.7820
W INE S T O R AG E
B U I L T- I N
Flush Inset Application—WS-30 | BW-30
F ULL-S CALE T E MPL ATE
24" (610)
TO BACK WALL
For panels thicker than 3/4" (19), a 90° door stop may be
required to prevent interference with adjacent cabinets.
1 1/4" (32)
PRO 48
2 3/16" (56)
ASSUMES
3/4" (19)
FLUSH INSET
PANEL
THICKNESS
I N T E G R AT E D
WINE
1" (25) THICK
PANEL
3/4" (19) THICK
FLUSH INSET PANEL
(TYPICAL)
1/4" (6) BACKER
0"
1" (25)
SCALE
110° door opening (top view).
subzero.com/specs
|
85
UNDERCOUNTER
PANEL
B U I L T- I N
W INE S T O R AG E
PRO 48
FILLER STRIP
11/4" (32)
DOOR
CLOSED
Dual Standard Installation—WS-30 | BW-30
DOOR
OPEN 110°
WINE
I N T E G R AT E D
APPROX PROFILE OF
STAINLESS STEEL WRAPPED
DOOR AND HANDLE
F ULL-S CALE T E MPL ATE
UNDERCOUNTER
Typical framed, overlay or stainless steel dual installation
with filler strip at maximum 110° door opening. Panel thickness may require a 90° door stop.
0"
1" (25)
SCALE
Dual standard installation (top view).
86
|
Sub-Zero Customer Care 800.222.7820
W INE S T O R AG E
B U I L T- I N
FILLER STRIP
PRO 48
1 1/2" (38)
1/2" (13)
WINE
Dual Flush Inset Installation—WS-30 | BW-30
DOOR
CLOSED
I N T E G R AT E D
PROFILE OF 3/4" (19) FLUSH INSET PANEL
AND TUBULAR HANDLE
DOOR
OPEN 110°
F ULL-S CALE T E MPL ATE
Typical flush inset dual installation with filler strip at maximum 110° door opening. Panel thickness may require a 90°
door stop.
1" (25)
SCALE
Dual flush inset installation (top view).
subzero.com/specs
|
87
UNDERCOUNTER
0"
U N DER CO UNT E R RE FRIGE RATION
B U I L T- I N
Undercounter Refrigeration
U N D ER C O U N TER MO D ELS
UC-24R
UC-24BG
UC-24C(I)
PRO 48
Sub-Zero undercounter refrigeration is a helpful addition to a
master suite, bar, home office or media room. In the kitchen,
a high-volume ice machine is a must for entertaining. The
design flexibility of these compact yet roomy units makes
them all the more welcome in any room or outdoor kitchen.
They are ready to be fitted with a custom cabinet panel or
can be ordered with a stainless steel panel.
UC-24RO
I N T E G R AT E D
I C E MAC H I N E M O D ELS
UC-15I(P)
UC-15I(P)O
WINE
|
89
UNDERCOUNTER
subzero.com/specs
B U I L T- I N
U N DER CO UNT E R RE FRIGE RATION
Overall Dimensions
U N DER CO UNT E R
I C E MAC H I N E
23 7/8" (606)
14 3/4" (375)
24" (610)
33 5/8"
34"
PRO 48
23" (584)
(854)
(864)
4" (102)
I N T E G R AT E D
4" (102)
18"
(457)
25 3/8"
(645)
6"
(152)
26" (660)
8"
(203)
SPECIFICATIONS
WINE
I NT E R I O R C A PA C I T Y—CU FT (L )
UC-24R, UC-24RO
UC-24BG
UC-24C(I)
SPECIFICATIONS
RE FR
5.7 (161)
6.0 (170)
3.6 (102)
1.1 (31)
SH I P P I N G W E I G H T
L B (KG )
24" Model
130 (59)
Refer to page 95 for door clearance information.
UNDERCOUNTER
FRZR
90
|
Sub-Zero Customer Care 800.222.7820
STORAGE C A PAC ITY
LB ( K G )
UC-15I(P), UC-15I(P)O
26 (12)
SH IP P IN G WEIGH T
LB ( K G )
Ice Machine
100 (45)
Model UC-15I overall dimensions do not include panel or
handle.
U N DER CO UNT E R RE FRIGE RATION
B U I L T- I N
Opening Dimensions
DUAL INSTALLATION
U N DER CO UNT E R
24" (610)
OPENING
DEPTH
TOP VIEW
Dual installation kits are available through an authorized
Sub-Zero dealer. For local dealer information, visit the find a
showroom section of our website, subzero.com. For questions regarding the installation, call Sub‑Zero customer care
at 800-222-7820.
34 1/2"
W
(876)
OPENING
HEIGHT
OPENING WIDTH
I N T E G R AT E D
SIDE VIEW
FRONT VIEW
OPENING WIDTH
24" Model
Ice Machine
W
24" (610)
15 1/4" (387)
DUAL OPENING WIDTH
Two 24" Models
PRO 48
If two units are installed side by side, a dual installation kit
may be required. Installations without a custom filler strip
require a dual installation kit. If a dual installation kit is not
specified, a 2" (51) filler strip is recommended between units.
Dual installations without a filler strip can only be accomplished using two units with opposite hinges. Refer to the
illustrations below.
W
48 1/8"
WITHOUT FILLER STRIP
Opposite hinges.
FILLER STRIP
Same side hinges.
(1222)
Dual installation kit required.
WINE
|
91
UNDERCOUNTER
subzero.com/specs
B U I L T- I N
U N DER CO UNT E R RE FRIGE RATION
Electrical
PRO 48
The electrical supply should be located within the shaded
area shown in the illustration. For ice machine models, it is
recommended that electrical supply be placed in an adjacent cabinet. A separate circuit, servicing only this appliance is required.
IMPORTANT NOTE: For outdoor models UC-24RO and
UC-15I(P)O, a ground fault circuit interrupter (GFCI) is
required to reduce the risk of electrical shock. A GFCI is not
recommended for use with other undercounter models and
may cause interruption of operation.
Installation must comply with all applicable electrical codes.
I N T E G R AT E D
LEFT SIDE
OF OPENING
2"
(51)
15 1/2"
(394)
3" (76)
FLOOR
UNDERCOUNTER
WINE
Electrical supply location.
92
|
Sub-Zero Customer Care 800.222.7820
ELECTRICAL REQUIREMENTS
Electrical Supply
Service
Receptacle
115 VAC, 60 Hz
15 amp
3-prong grounding-type
U N DER CO UNT E R RE FRIGE RATION
B U I L T- I N
Plumbing
IMPORTANT NOTE: A reverse osmosis system can be used
provided there is constant water pressure as indicated in the
chart below at all times. A copper line is not recommended
for this application.
ICE MACHINE DRAIN
Ice machine models can be ordered with or without a drain
pump. Models without a pump will drain water by gravity.
A drain must be installed.
The drain and inlet water tubes must be plumbed before
connecting to the ice machine. For the gravity drain, horizontal drain lines must have a 1/4" (6) per 12" (305) fall. An air
gap will likely be required between the unit and drain.
A stand pipe with a trap below is acceptable for the drain.
PRO 48
The water supply line should be located within the shaded
area shown in the illustrations below. The water supply line
should be connected to the house supply with an easily
accessible shut-off valve between the supply and the
unit. Do not use self‑piercing valves. A saddle valve kit is
avail­able through an authorized Sub-Zero dealer. For local
dealer information, visit the find a showroom section of our
website, subzero.com.
PLUMBING REQUIREMENTS
1/4"
Water Supply
Pressure (UC-24CI)
OD copper, braided stainless steel or PEX tubing
20–100 psi (1.4–6.9 bar)
20–80 psi (1.4–5.5 bar)
Excess Line for Connection
I N T E G R AT E D
Pressure (UC-15I)
36" (914)
LEFT SIDE
OF OPENING
8"
1/2"
(13)
2"
(51)
(203)
24" (610)
ROUGH
OPENING
DEPTH
LOCATION OF
WATER LINE
15 1/2"
(394)
3" (76)
Model UC-24CI.
WINE
AREA EXTENDS 1/2" (13)
FORWARD ON FLOOR
TOP VIEW
Ice machine.
15 1/4" min (387)
ROUGH
OPENING WIDTH
341/2" (876)
POSITION OUTLET
WITH GROUNDING
PRONG ON RIGHT
LOCATE
ELECTRICAL
WITHIN
SHADED AREA
MINIMUM
HEIGHT
REQUIRED
4" (102)
FRONT VIEW
subzero.com/specs
|
93
UNDERCOUNTER
ROUGH
OPENING
HEIGHT
33 5/8" (854)
B U I L T- I N
U N DER CO UNT E R RE FRIGE RATION
Custom Panel
For overlay undercounter models, custom door panels and
handle hardware must be provided. Refer to the charts for
panel requirements and dimensions.
PRO 48
Finish all sides of the custom panels. They may be visible
when the door is open or through the window of glass door
models.
PANEL REQUIREMENTS
W E I G H T P E R PA N E L
UC-24R, UC-24C(I)
UC-24BG
UC-15I(P)
PA N E L T H I C K N E S S
UNDERCOUNTER
WINE
I N T E G R AT E D
All Panels
94
|
Sub-Zero Customer Care 800.222.7820
MA X
20 lb (9 kg)
10 lb (5 kg)
15 lb (7 kg)
MIN
5/8"
(16)
M O D EL U C -2 4 B G
For model UC-24BG, the custom door panel will attach
directly to the door frame with screws through a series of
pre-drilled holes. Refer to the illustration below.
Do not install a solid panel on a glass door unit. A solid door
is available as a sales accessory and must be installed if a
solid panel is being specified. Service may be required to
install the door. Contact an authorized Sub-Zero dealer for
more information. Overall dimensions are the same for glass
and solid door panels.
U N DER CO UNT E R RE FRIGE RATION
B U I L T- I N
Custom Panel
Standard Handles
O VER LAY PANEL DIME NSIONS
Optional stainless steel tubular and pro handles are avail­
able through an authorized Sub-Zero dealer. For local dealer
information, visit the find a showroom section of our
website, subzero.com.
A
H
A
A
H
Refer to the chart below for standard handle lengths for
undercounter models.
A
UC-24R, UC-24C(I),
UC-15I(P)
W
UC-24BG
HANDLE LENGTH
TU BU L A R
Undercounter
24 1/4"
Outdoor Model
PRO
(616)
22 1/2"
(572)
NA
15 11/16"
(399)
|
95
PRO 48
W
PANEL DIMENSIONS
MODEL
24" Model
Ice Machine
ST I L E S | R A I L S
UC-24BG
W
H
23 3/4" (603)
15" (381)
30 1/16" (764)
30 3/8" (772)
A
2 1/4" (57) min
I N T E G R AT E D
DOOR CLEARANCE
Undercounter models can be installed flush with surrounding cabinetry. Depending on the thickness of the
custom door panel, it may be necessary to install the unit
1/4" (6) beyond the front surface of adjacent cabinetry to
prevent interference when the door is opened to 145°. Refer
to the full-scale template on page 97.
WINE
UNDERCOUNTER
subzero.com/specs
B U I L T- I N
U N DER CO UNT E R RE FRIGE RATION
Wine Rack Wood Facing
F ULL-S CALE T E MPL ATE
WOOD FACING WIDTH
UC-24BG
UC-24C(I)
19 1/2" (495)
(495)
PRO 48
The natural cherrywood facing on wine storage racks can
be stained and sealed, or replaced with wood more complementary to surrounding cabinetry. Refer to the full-scale
template below for profile dimensions of the wood facing
and the chart for widths.
W
19 1/2"
1/2"
5/8"
(13)
(16)
7/64" (3)
1/4"
(6)
I N T E G R AT E D
27/32"
7/64"
(3)
(21)
11/2"
(38)
27/32"
(21)
23/64"
7/32" (6)
23/64"
(9)
9/16"
(14)
IW-18, IW-24,
IW-30, IW-30R
(9)
5/64"
(2)
9/16"
(14)
5/64"
(2)
424G, UW-24,
424FSG, UW-24FS, WS-30
UNDERCOUNTER
WINE
Wine rack wood facing profile.
Sub-Zero, Sub-Zero & Design, Dual Refrigeration, The Living Kitchen, Great American Kitchens The Fine Art of Kitchen Design, and Ingredients are registered trademarks and service
marks of Sub-Zero, Inc. Wolf, Wolf & Design, Wolf Gourmet, W & Design and the color red as applied to knobs are registered trademarks and service marks of Wolf Appliance, Inc.
All other trademarks or registered trademarks are property of their respective owners in the United States and other countries.
96
|
Sub-Zero Customer Care 800.222.7820
U N DER CO UNT E R RE FRIGE RATION
B U I L T- I N
Door Clearance—Undercounter
F ULL-S CALE T E MPL ATE
To allow for a 145° door opening, the unit should extend
a minimum of 1/4" (6) beyond the front surface of adjacent cabinetry. The unit can be installed flush, however,
there is potential for interference with the panel if the
door is opened past 90°.
PRO 48
UNDERCOUNTER
UNIT
ADJACENT
CABINETRY
I N T E G R AT E D
DOOR CLOSED
1/2"
(13)
3/4" (19) DOOR PANEL
1/4" (6)
1/8" (3)
WINE
HINGE AT 145°
OPENING
(DOOR OPENS PAST 145°)
1" (25)
SCALE
145° door opening (top view).
subzero.com/specs
|
97
UNDERCOUNTER
0"
Sub-Zero Residential Limited Warranty
FOR RESIDENTIAL USE
FULL TWO YEAR WARRANTY*
For two years from the date of original installation, this Sub-Zero product warranty covers all parts and
labor to repair or replace, under normal residential use, any part of the product that proves to be defective in materials or workmanship. All service provided by Sub-Zero under the above warranty must be
performed by Sub-Zero factory certified service, unless otherwise specified by Sub-Zero, Inc. Service will
be provided during normal business hours.
FULL FIVE YEAR SEALED SYSTEM WARRANTY
For five years from the date of original installation, this Sub-Zero product warranty covers all parts and
labor to repair or replace, under normal residential use, these parts that prove to be defective in materials
or workmanship: compressor, condenser, evaporator, drier and all connecting tubing. All service provided
by Sub-Zero under the above warranty must be performed by Sub-Zero factory certified service, unless
otherwise specified by Sub-Zero, Inc. Service will be provided during normal business hours.
LIMITED TWELVE YEAR SEALED SYSTEM WARRANTY
For twelve years from the date of original installation, Sub-Zero will repair or replace the following parts
that prove to be defective in materials or workmanship: compressor, condenser, evaporator, drier and all
connecting tubing. If the owner uses Sub-Zero factory certified service, the service provider will repair or
replace these parts with the owner paying for all other costs, including labor. If the owner uses non-certified service, the owner must contact Sub-Zero, Inc. (using the information below) to receive repaired or
replacement parts. Sub-Zero will not reimburse the owner for parts purchased from non-certified service
or other sources.
TERMS APPLICABLE TO EACH WARRANTY
The warranty applies only to products installed for normal residential use. The warranty applies only to
products installed in any one of the fifty states of the United States, the District of Columbia or the ten
provinces of Canada. This warranty does not cover any parts or labor to correct any defect caused by
negligence, accident or improper use, maintenance, installation, service or repair.
THE REMEDIES DESCRIBED ABOVE FOR EACH WARRANTY ARE THE ONLY ONES THAT SUB-ZERO, INC.
WILL PROVIDE, EITHER UNDER THIS WARRANTY OR UNDER ANY WARRANTY ARISING BY OPERATION OF
LAW. SUB-ZERO, INC. WILL NOT BE RESPONSIBLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES
ARISING FROM THE BREACH OF THIS WARRANTY OR ANY OTHER WARRANTY, WHETHER EXPRESS,
IMPLIED OR STATUTORY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you. This warranty gives you specific legal rights and you may also
have other legal rights that vary from state to state.
To receive parts and/or service and the name of Sub-Zero factory certified service nearest you, contact
Sub-Zero, Inc., P.O. Box 44848, Madison, WI 53744; check the contact & support section of our website,
subzero.com, email us at customerservice@subzero.com or call 800-222-7820.
*Stainless steel (doors, panels, handles, product frames and interior surfaces) are covered by a limited
60-day parts and labor warranty for cosmetic defects.
*Replacement water filters and air purification cartridges are not covered by the product warranty.
Sub-Zero Outdoor Limited Warranty*
FOR RESIDENTIAL USE
FULL ONE YEAR WARRANTY**
For one year from the date of original installation, this Sub-Zero product warranty covers all parts and labor
to repair or replace, under normal residential use, any part of the product that proves to be defective in
materials or workmanship. All service provided by Sub-Zero under the above warranty must be performed
by Sub-Zero factory certified service, unless otherwise specified by Sub-Zero, Inc. Service will be provided
during normal business hours.
FULL FIVE YEAR SEALED SYSTEM WARRANTY
For five years from the date of original installation, this Sub-Zero product warranty covers all parts and
labor to repair or replace, under normal residential use, these parts that prove to be defective in materials
or workmanship: compressor, condenser, evaporator, drier and all connecting tubing. All service provided
by Sub-Zero under the above warranty must be performed by Sub-Zero factory certified service, unless
otherwise specified by Sub-Zero, Inc. Service will be provided during normal business hours.
TERMS APPLICABLE TO EACH WARRANTY
The warranty applies only to products installed for normal residential use. The warranty applies only to
products installed in any one of the fifty states of the United States, the District of Columbia or the ten
provinces of Canada. This warranty does not cover any parts or labor to correct any defect caused by
negligence, accident or improper use, maintenance, installation, service or repair.
THE REMEDIES DESCRIBED ABOVE FOR EACH WARRANTY ARE THE ONLY ONES THAT SUB-ZERO, INC.
WILL PROVIDE, EITHER UNDER THIS WARRANTY OR UNDER ANY WARRANTY ARISING BY OPERATION OF
LAW. SUB-ZERO, INC. WILL NOT BE RESPONSIBLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES
ARISING FROM THE BREACH OF THIS WARRANTY OR ANY OTHER WARRANTY, WHETHER EXPRESS,
IMPLIED OR STATUTORY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you. This warranty gives you specific legal rights and you may also
have other legal rights that vary from state to state.
To receive parts and/or service and the name of Sub-Zero factory certified service nearest you, contact
Sub-Zero, Inc., P.O. Box 44848, Madison, WI 53744; check the contact & support section of our website,
subzero.com, email us at customerservice@subzero.com or call 800-222-7820.
*Product must be approved for outdoor use, designated by model and serial number.
**Stainless steel (doors, panels, handles, product frames and interior surfaces) are covered by a limited
60-day parts and labor warranty for cosmetic defects.
**Replacement water filters are not covered by the product warranty.
SUBZERO.COM
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising