EN Installation, Operation and Maintenance Instructions FR Instructions d’installation, d’utilisation et d’entretien ES Instrucciones de instalación, operación y mantenimiento Wine Cellars Celliers Bodegas para vinos ML15WS ML24WS ML24WD Note: Wine Cellars are designed exclusively for the storage of wine. Wine Cellars cannot attain storage temperatures suitable for fresh food storage. Remarque : Les celliers sont conçues exclusivement pour y garder des vins. Elles ne peuvent pas atteindre des températures de conservation convenant à l’entreposage d’aliments frais. Nota: Estas bodegas están diseñadas exclusivamente para el almacenamiento de vino. Las bodegas para vinos no pueden alcanzar las temperaturas adecuadas para el almacenamiento de alimentos frescos. CONTENTS Important Safety Instructions Contents: Warnings and safety instructions appearing in this guide are not meant to cover all possible conditions and situations that may occur. Common sense, caution, and care must be exercised when installing, maintaining, or operating this appliance. Safety information ...............................................................2 Unpacking your appliance ..................................................3 Warranty registration .....................................................3 Installing your appliance ......................................................4 Cabinet clearances .........................................................4 Leveling the appliance ....................................................4 Electrical connection ......................................................5 Installing the anti-tip device .................................................6 Product dimensions ............................................................8 Using your Electronic control ............................................10 Starting your appliance ..................................................10 Sleep mode ...................................................................10 Turning your appliance "ON" or "OFF" ..........................10 Adjusting the temperature .............................................11 Interior display lighting ...................................................11 Temperature mode ........................................................12 Control lock ....................................................................12 Alarms ...........................................................................12 Door ajar ..................................................................12 Power failure .............................................................12 Temperature alarm ....................................................12 Vacation mode ..............................................................13 Overlay door panel installation ........................................14 Shelving configurations ....................................................18 Care and cleaning .............................................................20 Energy saving tips ............................................................20 Door alignment .................................................................21 Obtaining service .............................................................21 Troubleshooting ................................................................22 Warranty ...........................................................................23 Recognize Safety Symbols, Words, and Labels. ! WARNING WARNING - You can be killed or seriously injured if you do not follow these instructions. ! CAUTION CAUTION-Hazards or unsafe practices which could result in personal injury or property / product damage. NOTE NOTE-Important information to help assure a problem free installation and operation. State of California Proposition 65 Warnings: WARNING: This product contains one or more chemicals known to the State of California to cause cancer. WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other reproductive harm.. is committed to building a quality product in an environmentally friendly manner. Our processes are tightly controlled and closely monitored. We have achieved certifications in ISO 9001 for quality assurance, ISO 14001 for environmental management, and OHSAS 18001 for occupational health and safety from Lloyd’s Register Quality Assurance. 2 UNPACKING YOUR APPLIANCE ! Warranty Registration WARNING It is important you send in your warranty registration card immediately after taking delivery of your appliance or you can register online at www.agamarvel.com. EXCESSIVE WEIGHT HAZARD Use two or more people to move product. Failure to do so can result in personal injury. The following information will be required when registering your appliance. Service Number Serial Number Date of Purchase Dealer’s name and address Remove Interior Packaging Your appliance has been packed for shipment with all parts that could be damaged by movement securely fastened. Remove internal packing materials and any tape holding internal components in place. The owners manual is shipped inside the product in a plastic bag along with the warranty registration card, and other accessory items. The service number and serial number can be found on the serial plate which is located inside the cabinet on the left side near the top. (See figure 1). Important Keep your carton and packaging until your appliance has been thoroughly inspected and found to be in good condition. If there is damage, the packaging will be needed as proof of damage in transit. Afterwards please dispose of all items responsibly. ! Online registration available at www.agamarvel.com CAUTION Dispose of the plastic bags which can be a suffocation hazard. XXXXXXXXXXXX XXXXXXXXXXXX Note to Customer This merchandise was carefully packed and thoroughly inspected before leaving our plant. Responsibility for its safe delivery was assumed by the retailer upon acceptance of the shipment. Claims for loss or damage sustained in transit must be made to the retailer. Figure 1 NOTE DO NOT RETURN DAMAGED MERCHANDISE TO THE MANUFACTURER - FILE THE CLAIM WITH THE RETAILER. ! ! CAUTION Help Prevent Tragedies Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous - even if they sit out for "just a few days". CAUTION If you are getting rid of your old refrigerator, please follow the instructions below to help prevent accidents. If the appliance was shipped, handled, or stored in other than an upright position for any period of time, allow the appliance to sit upright for a period of at least 24 hours before plugging in. This will assure oil returns to the compressor. Plugging the appliance in immediately may cause damage to internal parts. Before you throw away your old refrigerator or freezer: • Take off the doors or remove the drawers. • Leave the shelves in place so children may not easily climb inside. 3 INSTALLING YOUR APPLIANCE Select Location The proper location will ensure peak performance of your appliance. We recommend a location where the unit will be out of direct sunlight and away from heat sources. To ensure your product performs to specifications, the recommended installation location temperature range is from 55 to 100°F (13 to 38°C). Front Grille, keep this area open. Cabinet Clearance Ventilation is required from the bottom front of the appliance. Keep this area open and clear of any obstructions. Adjacent cabinets and counter top can be installed around the appliance as long as the front grille remains unobstructed. Overlay door models with articulated hinges are intended for built-in applications only. Rear Leveling Legs Front Leveling Legs Figure 2 Leveling Legs ! Adjustable legs at the front and rear corners of the appliance should be set so the unit is firmly positioned on the floor and level from side to side and front to back. The overall height of your Marvel appliance may be adjusted higher (by turning the leveling leg out, CCW) and lower (by turning the leveling leg in, CW) dimensions as shown in Table "B". WARNING An optional stacking kit, shown in Table "A", is required to stack products. Failure to use a stacking kit could result in personal injury. Contact your dealer or Aga Marvel customer service at 800-223-3900 to order. Color Door Swing Kit Part Number Stainless Steel Left Hand 42249095 Stainless Steel Right Hand 42249096 Black Left Hand 42249097 Black Right Hand 42249098 White Left Hand 42249099 White Right Hand 42249100 To adjust the leveling legs, place the appliance on a solid surface and protect the floor beneath the legs to avoid scratching the floor. With the assistance of another person, lean the appliance back to access the front leveling legs. Raise or lower the legs to the required dimension by turning the legs. Repeat this process for the rear by tilting the appliance forward using caution. On a level surface check the appliance for levelness and adjust accordingly. The front grille screws may be loosened and the grille adjusted to the desired height. When adjustment is complete tighten the two front grille screws. (See Figure 3). Table A ! CAUTION Front Grille Do not obstruct the front grille. The openings within the front grille allow air to flow through the condenser heat exchanger. Restrictions to this air flow will result in increased energy usage and loss of cooling capacity. For this reason it is important this area not be obstructed and the grille openings kept clean. AGA MARVEL does not recommend the use of a custom made grille as air flow may be restricted. (See Figure 2). Minimum Height Maximum Height (S) or (G) 33 3⁄4" (85.7 cm) 34 3⁄4" (88.3 cm) (P) or (F) 34" (86.4 cm) 35" (88.9 cm) Model Door Style ML(15)(24)* ML(15)(24)* Table B 4 INSTALLING YOUR APPLIANCE ! WARNING Electrical Shock Hazard • Do not use an extension cord with this appliance. They can be hazardous and can degrade product performance. • This appliance should not, under any circumstances, be installed to an un-grounded electrical supply. • Do not remove the grounding prong from the power cord. • Do not use an adapter. • Do not splash or spray water from a hose on the appliance. Doing so may cause an electrical shock, which may result in severe injury or death. Electrical Connection A grounded 115 volt, 15 amp dedicated circuit is required. Front grille Figure 3 This product is factory equipped with a power supply cord that has a three-pronged, grounded plug. It must be plugged into a mating grounding type receptacle in accordance with the National Electrical Code and applicable local codes and ordinances (see Figure 4). If the circuit does not have a grounding type receptacle, it is the responsibility and obligation of the customer to provide the proper power supply. The third ground prong should not, under any circumstances, be cut or removed. Front grille screw Figure 4 NOTE Ground Fault Circuit Interrupters (GFCI) are prone to nuisance tripping which will cause the appliance to shut down. GFCI’s are generally not used on circuits with power equipment that must run unattended for long periods of time, unless required to meet local building codes and ordinances. 5 INSTALLING THE ANTI TIP DEVICE Anti-Tip Bracket WARNING ! • ALL APPLIANCES CAN TIP RESULTING IN INJURY. • INSTALL THE ANTI-TIP BRACKET PACKED WITH THE APPLIANCE. • FOLLOW THE INSTRUCTIONS BELOW 211⁄2" (54.6 cm) Leveling Leg Bottom View of Wine Cellar Front of cabinet Anti-Tip Device ! Figure 5 CAUTION Step by step instructions for locating the position of the bracket: If your wine cellar is not located under a counter top (free standing), you must use an anti-tip device installed as per these instructions. If the wine cellar is removed from its location for any reason, make sure that the device is properly engaged when you push the wine cellar back into the original location. If the device is not properly engaged, there is a risk of the wine cellar tipping over, with the potential for property damage or personal injury. 1) Decide where you want to place the wine cellar. Slide it into place, being careful not to damage the floor, leaving 1" (2.5 cm) of clearance from the rear wall to allow room for the anti-tip bracket. 2) Raise the rear leveling legs approximately 1⁄4" (6 mm) to allow engagement with the anti-tip bracket. Level the unit by adjusting all the leveling legs as required. Turning the leveling leg counterclockwise will raise the unit and clockwise will lower the unit. 3) Make sure the wine cellar is in the desired location, then mark on the floor the rear and side corner of the cabinet where the anti-tip bracket will be installed. If the installation does not allow marking the rear corner of the cabinet, then make temporary lines on the floor marking the front corner of the cabinet, excluding the door. Slide the wine cellar out of the way. From the temporary line extend the sidewall line back 211⁄2" (54.6 cm) as shown in Figure 6. NOTE If installing on a concrete floor, concrete fasteners are required, (not included with the anti-tip kit). ! 4) Align the anti-tip bracket to the marks on the floor so the side of the bracket lines up with the side of the cabinet mark, and the "V" notches on the anti-tip bracket line up with the end of the 211⁄2" (54.6 cm) line (Rear of cabinet line). CAUTION Any finished flooring should be protected with appropriate material to avoid damage when moving the unit. 5) Fasten the anti-tip bracket to the floor using the supplied screw. (See Figure 6). 6) Slide the cabinet back into position, making sure the rear cabinet leveling leg slides under the anti-tip bracket engaging the slot. Floor Mount Installation The anti-tip bracket is to be located on the floor in the left or right rear corner of the wine cellar as shown in Figure 5. 6 INSTALLING THE ANTI TIP DEVICE ! WARNING TIP OVER HAZARD: One of the rear cabinet leveling legs must be engaged under an anti-tip bracket. NOTE When the floor mounted anti-tip bracket is used the minimum adjusted height of the cabinet is increased by 3 ⁄8" (9 mm). nt o Fro net bi f ca line Sid eo f c Rear Leveling leg ab ine t li ne Figure 6a Screw 211⁄2" (54.6 cm) Figure 6 f ca Re o ar e t lin e bin "V" notches in bracket 7 "V" notches in bracket PRODUCT DIMENSIONS ROUGH-IN OPENING DIMENSIONS CABINET DIMENSIONS MODEL "A" "B" "C" "D" "E" "F" "G" "H" "J" ML15WSG 15" (38.1 cm) **34" to 35" (86.4 to 88.9 cm) * 147⁄8" (37.8 cm) 333⁄4" to 343⁄4" (85.7 to 88.3 cm) 2323⁄32" (60.2 cm) 2521⁄32" (65.2 cm) 3713⁄32" (95 cm) 1611⁄16" (42.4 cm) ML15WS(P) or (F) 15" (38.1 cm) **34 ⁄4" to 35 ⁄4" (87 to 89.5 cm) * 147⁄8" (37.8 cm) 34" to 35" (86.4 to 88.9 cm) 227⁄8" (58.1 cm) - 371⁄2" (95.2 cm) 141⁄8" 35.9 cm) ML24W*G 24" (61 cm) **34" to 35" (86.4 to 88.9 cm) * 237⁄8" (60.7 cm) 333⁄4" to 343⁄4" (85.7 to 88.3 cm) 2323⁄32" (60.2 cm) 2521⁄32" (65.2 cm) 4613⁄32" (117.9 cm) 2511⁄16" (65.2 cm) ML24W*(P) or (F) 24" (61 cm) **341⁄4" to 351⁄4" (87 to 89.5 cm) * 237⁄8" (60.7 cm) 34" to 35" (86.4 to 88.9 cm) 227⁄8" (58.1 cm) - 461⁄2" (118.1 cm) 231⁄8" (58.7 cm) 1 1 DOOR STYLE (G) Glass Frame Door (P) Solid Overlay Door (no handle) (F) Frame Glass Overlay Door (no handle) "A" "B" "E" "C" Figure 7 "D" Figure 7a If necessary to gain clearance inside the rough-in opening a hole can be cut through the adjacent cabinet and the power cord routed through this hole to a power outlet. Another way to increase the available opening depth is to recess the power outlet into the rear wall 1" (2.5 cm) to gain the thickness of the power cord plug. 8 PRODUCT DIMENSIONS PRODUCT DATA MODEL ELECTRICAL REQUIREMENTS # PRODUCT WEIGHT ML15WSG 115V/60Hz/15A 105 lbs (47.7 kg) ML15WS(P) or (F) 115V/60Hz/15A 105 lbs (47.7 kg) ML24W*G 115V/60Hz/15A 140 lbs (63.6 kg) ML24W*(P) or (F) 115V/60Hz/15A 140 lbs (63.6 kg) "J" "H" "D" "G" "E" 1" (2.5 cm) Figure 8 211⁄2" (54.6cm) "F" * Depth dimension of rough-in opening may vary depending on each individual installation. To recess entire door "F" dimension plus 1" (2.5 cm) for thickness of power cord plug is required. APPLIES TO THE FOLLOWING MARVEL MODELS ML15WS ML24WS ML24WD ** Minimum rough-in opening required is to be larger than the adjusted height of the cabinet. # A grounded 15 amp dedicated circuit is required. Follow all local building codes when installing electrical and appliance. ! WARNING Floor mount Anti-tip Bracket must be installed for freestanding applications. Not required for built in applications. 9 USING YOUR ELECTRONIC CONTROL Temp Minus keypad On/Off keypad Upper/Lower Temp zones Plus (Dual Zone keypad models only) Lights keypad (glass door Lock only) keypad Display Area System Status indicators Figure 9 Electronic control Power Failure ALARM RESET To wake the display press any keypad. A confirm tone will sound, and the current storage compartment temperature will be displayed. Starting your appliance (Single and Dual Zone: Plug the appliance power cord into a 115 volt wall outlet. Your appliance is shipped from the factory in the "On" position and will begin start-up of cooling as soon as power is supplied. If the appliance does not start, confirm that the wall outlet has power, and that the control is in the "On" position, (See "Turning your appliance On and Off" below). The control display is covered with a clear plastic film. This film may be removed by carefully lifting the film at a corner. On initial power up, the control display will indicate a "Power Failure" alarm. This is a normal condition as the appliance was powered-up at the factory for quality inspection and then removed from power. A momentary press of the "On/Off" keypad will reset this alarm condition. (See Alarms section on page 12). The sleep mode can be disabled if you prefer to have the display on continuously. Press and hold the "Lock" keypad until the display goes past "Loc" and reads "nSL". To enable the sleep mode, repeat the instruction, again going past "Loc" until the display reads "SLP". Turning your appliance ON and OFF (Single and Dual Zone): Sleep mode (Single and Dual Zone): If no keypads are pressed for 60 seconds, the display will enter sleep mode to conserve power. The control panel will go dark with the exception of the system status "OK" indicator which will remain enabled. Alarm conditions will wake the display, (see alarms on page 12). To make the following changes to the control settings (turning the appliance ON/OFF, adjusting the temperature, changing the interior lights, and activating vacation mode), the control must be awake. If the appliance is "On", (and out of sleep mode) the temperature will be shown in the display area of the control. To turn the appliance "Off", press and hold the "On/Off" keypad for 4-seconds. "OFF" will now be displayed on the control. To turn the appliance "On", press and hold the "On/Off" keypad for 4-seconds. 10 USING YOUR ELECTRONIC CONTROL Adjusting the temperature: Lower zone selected NOTE When initially loading your product with warm contents, it may take up to 48-hours for the storage compartment temperature to stabilize. When making temperature set-point changes, it may take up to 24-hours for the stored contents to stabilize at your new set-point temperature. Factors that affect the storage compartment stabilized temperature: • Changes to temperature setting. • Room temperature changes. • Temperature of stored contents. - Loading warm contents. - Cold content load will delay the change to a warmer set-point temperature. - Warm content load will delay the change to a colder set-point temperature. • Usage, (number and duration of the door openings). • Use of the storage compartment display lighting, (glass door product only). • Installation of the appliance in direct sunlight or next to a heat source. Single Zone Models: To set or check the set-point temperature (with the control out of sleep mode), press the "-" or "+" keypads. "SET" will be indicated on the user interface panel and the current set-point temperature will display and flash. Subsequent presses of the "-" or "+" keypads will adjust the temperature colder or warmer respectively. When you have reached your desired set-point temperature, press the "On/Off" keypad to accept, or do nothing and the "Set" mode will timeout in 10-seconds accepting the displayed temperature as the new set-point. The available set-point temperature range for your appliance is 40°F (4.5°C) to 65°F (18.4°C). If you attempt to adjust the temperature outside of this range you will receive an audible notification. Upper zone selected Dual Zone Models: Temperatures can be set for each individual zone (upper and lower) in the dual zone wine cellar. To do so you must first select the zone you want to set the temperature for. You do so by pressing the upper or lower button on the display. When pressed the LED light will be illuminated for the respective display. To change the set temperature for a particular zone, with the zone selected and out of sleep mode, press the "-" or "+" keypads. "SET" will be indicated on the user interface panel and the current set-point temperature will display and flash. Subsequent presses of the "-" or "+" keypads will adjust the temperature colder or warmer respectively. When you have reached your desired set-point temperature, press the "On/Off" keypad to accept, or do nothing and the "Set" mode will time-out in 10-seconds accepting the displayed temperature as the new set-point. The available set-point temperature range for your appliance is 45°F (7.3°C) to 55°F (12.9°C) for the lower zone and 55°F (12.9°C) to 62°F (16.8°C) for the upper zone. If you attempt to adjust the temperature outside of these ranges you will receive an audible notification. Interior display lighting (Single and Dual Zone): (Glass door models only) Your appliance is equipped with a dual light level display lighting feature. With the control out of sleep mode press the "Light" keypad once to activate the interior lighting display feature at full illumination. A confirmation tone will sound, and the light bulb "Icon" will illuminate. Pressing the "Light" keypad a 2nd time will dim the lighting to 50%. A 3rd press will deactivate the display lighting feature. The display lighting will automatically deactivate after 4-hours. 11 USING YOUR ELECTRONIC CONTROL Power Failure Temperature mode (Single and Dual Zone): • The temperature mode is preset from the factory in Fahrenheit (°F) but you have the option to change it to Centigrade (°C). To change the mode, press and hold the "-" keypad, while pressing the "+" keypad, then release the "-" keypad. The temperature will now be displayed in Centigrade (°C). Repeat the procedure to change the temperature mode back to Fahrenheit (°F). Control lock (Single and Dual Zone): The control panel can be locked to avoid unintentional changes. To lock the control, press and hold the "Lock" keypad until the display reads "Loc" then release your finger from the keypad. The lock icon will flash 3-times and then continuously illuminate. When the control panel is locked, only the Lock keypad, System Status OK indicator , and the Alarm indicator are active. To un-lock the control panel, repeat this instruction until the display reads "nLc". Power failure - If power to the appliance is inter- rupted the System Status indicator will turn-off and the "Power Failure" indicator will flash. Additionally, an "ALARM RESET" indicator will be displayed below the "On/Off" keypad. No audible tone will sound. This alarm condition can be reset by momentarily pressing the "On/Off" keypad. If this alarm occurs, it is recommended that you check the condition of any perishables, even if the appliance is operating normally and the temperature has recovered, as prolonged power outages could result in excessive temperature excursions which may spoil perishables. Temp • Alarms (Single and Dual Zone): The control will alert you to conditions that could adversely affect the performance of the appliance. ALARM RESET ALARM RESET Temperature alarm - If the storage compartment temperature exceeds 10°F from set-point for more than a 1-hour duration, the System Status indicator will turn off, the "Temp" indicator will flash, and an audible tone will sound every 60-seconds. Additionally, an "ALARM RESET" indicator will be displayed below the "On/Off" keypad. This alarm condition can be reset by momentarily pressing the "On/Off" keypad. If this alarm occurs it is recommended that you check the condition of your stored contents, even though the appliance is operating normally and the temperature has recovered, as prolonged temperature excursions could spoil perishables. Door Ajar ALARM RESET NOTE • Door ajar - If the door is open, or not closed prop- erly, for more than 5-minutes the System Status OK indicator will turn-off, the "Door Ajar" indicator will flash, and a tone will sound every 60 seconds. Additionally, an "ALARM RESET" indicator will be displayed below the "On/Off" keypad. This alarm condition can be reset by closing the door or momentarily pressing the "On/ Off" keypad, (i.e.-if you are cleaning the storage compartment, etc.). The alarm will recur in 5-minutes if the alarm condition persists. Door Ajar Temp Multiple alarms are possible, i.e.- "Door Ajar" for a prolonged period may trigger a "Temp" alarm, in which case both "Door Ajar" and "Temp" indicators will activate. 12 USING YOUR ELECTRONIC CONTROL Vacation mode (Single and Dual Zone): This operating mode can be used to save energy during high cost energy periods, or when you won't be using your appliance for an extended period of time by disabling the lights, alarm tones, and keypad entry tones. Vacation mode also serves as a Sabbath mode, disabling functions and its controls in accordance with the weekly Sabbath and religious holidays observed within the Orthodox Jewish community. When used as Sabbath mode, you may open or close the door at any time to access contents without concern of directly turning on or off any lights, digital readouts, solenoids, fans, valves, compressor, icons, tones, or alarms. When activated, the display, alarm indicators and tones, keypad touch tones, interior lights, and all options are disabled. All keypad functions are disabled, with the exception of the "On/Off" keypad which is required to exit Vacationmode. Storage compartment temperatures are monitored and controlled at the settings prior to entering Vacation mode. To enter Vacation Mode (with the control out of sleep mode), press and hold the "On/Off" keypad until the display goes past "OFF" and reads "VAC". The display will flash "VAC" 3-times to acknowledge your request, then will display "VAC" continuously until Vacation mode is exited. A power outage will not exit Vacation mode, exiting can only be accomplished manually. To exit Vacation mode and return to normal operation, press and hold the "On/Off" keypad until the control displays the temperature. 13 OVERLAY DOOR PANEL INSTALLATION If you purchased an overlay panel model, your unit is equipped with articulated hinges to allow fully integrated built-in installations. Custom panel thicknesses of 5⁄8" (15 mm) and 3⁄4" (18 mm) are accommodated. ! ! Use extreme caution with the articulated hinges. The hinge is self closing and many pinch points exist prior to built-in installation. Do not remove the cabinet "Z" bracket from the top of the cabinet. CAUTION It is important to use the factory provided grille that came with the product to assure proper air flow is maintained through the condenser. The use of a custom grille is not recommended and will void the warranty. ! WARNING Loosen (do not remove ) these 2 phillips head screws on the top and bottom hinges WARNING Figure 10a Cabinet "Z" Bracket Overlay panel models are designed for use with builtin installations only. Use in freestanding installations could result in personal injury. Step 1: Removing the Door With a phillips screwdriver remove the screw and "P" clamp from the bottom of the door near the hinge. See Figure 10b. Disconnect the door wire harness by pressing and holding down the locking tab on the wire connector and pulling the connector apart. See Figure 11. Open the door and loosen the screws holding the hinges to the cabinet (2 at the top and 2 at the bottom hinge). Do not remove the screws but loosen them enough so the hinges can be slipped off of the screws when sliding the door to the side. ! Figure 10 "P" clamp and screw WARNING Figure 10b Bottom of door The articulated hinges have many pinch points. Carefully close / collapse the hinges as soon as the door is removed from the cabinet. With a helper, and being careful not to scratch the cabinet or the door, slide the door to the side about 1⁄2 inch and remove the hinges and door from the unit. Wire connector see Figure 11 Step 2: Remove the door gasket With the door laying on a flat surface and starting at a corner of the door remove the magnetic door gasket from the interior side of the door, see Figure 12. Set the gasket aside on a flat surface. There are 10 holes in the gasket retainer extrusions, (3 on each side and 2 at the top and bottom which are used to fasten the panel to the front of the door. The screws are provided in the literature pack. 14 OVERLAY DOOR PANEL INSTALLATION Press and hold down this tab on the wire connector and pull the connector apart. Figure 11 Hinge side of door Clearance for screw head, 4 places Figure 13 Left Hand Hinged Door 15" (38.1 cm) wide appliance Overlay panel flush with top and side of door. Clearance for hinge 2 places 143⁄4" (37.5 cm) Overlay panel to be centered on width of door. Holes in gasket retainer. 1 ⁄4" (6 mm) Deep 1" (25.4 mm) diameter counter bore 1⁄4" (6.4mm) 5" 47⁄8" deep 4 places. (12.7 cm) (12.4 cm) Figure 12a 31⁄8" (7.9 cm) 13⁄16" (3 cm) 13⁄4" (4.4 cm) 327⁄32" (9.7 cm) ⁄4" (6 mm) radius is permissible 1 Magnetic Gasket remove starting at a corner, grasp and pull away from the door. 31⁄8" (7.9 cm) Minimum 15⁄32" (2.9 cm) Figure 12 ! 3011⁄32" (77.1 cm) 41⁄8" (10.5 cm) Minimum 31⁄8" (7.9 cm) Minimum This side facing interior CAUTION Weight of overlay door panel must not exceed 15 pounds (6.8 kg) for a solid door model or 10 pounds (4.5 kg) for a glass door model. 111⁄16" (4.3 cm) 311⁄16" (9.4 cm) Figure 14 Left Hand Hinged Door 15" (38.1 cm) Wide Appliance Step 3: Cut and drill the overlay panel Depending on your model cut the overlay door panel to the dimensions shown in Figures 13 to 20. 11⁄2" (3.8 cm) typical 15 2" (5.1 cm) OVERLAY DOOR PANEL INSTALLATION ! Clearance for screw head, 4 places CAUTION Clearance for screw head, Weight of overlay door panel must not 4 places exceed 15 pounds (6.8 kg) for a solid door model or 10 pounds (4.5 kg) for a glass door model. Figure 15 Right Hand Hinged Door 15" (38.1 cm) wide appliance p To Figure 17 Left Hand Hinged Door 24" (61 cm) wide appliance Clearance for hinge 2 places 1 233⁄4" (60.3 cm) 47⁄8" 5" (12.4 cm) (12.7 cm) 13⁄4" (4.4 cm) Clearance for hinge at top and bottom 143⁄4" (37.5 cm) ⁄4" (6 mm) Deep 31⁄8" (7.9 cm) r oo d of Hinge side of door o Hinge side of door p To or o fd 1" (25.4 mm) diameter counter bore 1⁄4" (6 mm) deep 4 places. 13⁄4" (4.4 cm) 14" (35.6 cm) 47⁄8" (12.4 cm) 13⁄16" (3 cm) 1 ⁄4" (6 mm) Deep 13⁄16" (3 cm) 327⁄32" (9.7 cm) 3 1 ⁄8 " (7.9 cm) 327⁄32" (9.8 cm) ⁄4" (6 mm) radius is permissible 1 ⁄4" (6 mm) radius is permissible 1 3011⁄32" (77.1 cm) 31⁄8" (7.9 cm) Minimum This side facing interior 31⁄8" (7.9 cm) 3 1 ⁄8 " (7.9 cm) 31⁄8" (7.9 cm) Minimum 3011⁄32" (77.1 cm) 15⁄32" (2.9 cm) 15⁄32" (2.9 cm) This side facing interior 111⁄16" (4.3 cm) 41⁄8" (10.5 cm) 2" (5.1 cm) 311⁄16" (9.4 cm) 11⁄2" (3.8 cm) typical 111⁄16" (4.3 cm) Figure 16 Right Hand Hinged Door 15" (38.1 cm) wide appliance 41⁄8" (10.5 cm) Minimum 11⁄2" (3.8 cm) typical 16 2" (5.1 cm) 1" (2.5 cm) diameter x 1⁄4" (6 mm) deep 4 places 311⁄16" (9.4 cm) Figure 18 Left Hand Hinged Door 24" (61 cm) wide appliance OVERLAY DOOR PANEL INSTALLATION Clearance for hinge at top and bottom of do or ! Clearance for screw head, 4 places CAUTION Weight of overlay door panel must not exceed 15 pounds (6.8 kg) for a solid door model or 10 pounds (4.5 kg) for a glass door model. Hinge side of door To p Material Type #10 Wood Screw Hardwood 1 Softwood 7 ⁄8" (3.2 mm) Diameter. Pilot Hole ⁄64 (2.8 mm) Diameter. Pilot Hole Table C Step 4: Assemble the panel to the door The preferred method of attaching the panel to the door is to clamp the panel to the door so it cannot move while drilling the screw pilot holes. Use bar clamps or "C" clamps with pads on the clamping surfaces that will not mar the panel or the door. The custom overlay panel should be flush with the top of the door and centered along the width of the door. See Figure 12a. Drill holes through the gasket extrusion using the 10 holes as pilot holes. Use the drill size from the chart in Table "C", being careful not to drill through the front surface of the panel, drill no deeper than 1 ⁄2" (12.7 mm) deep. If the overlay panel is thinner than 5 ⁄8" (16 mm) thick shorter screws will have to be obtained. Fasten the panel to the door with the 10 screws provided in the literature pack. (See Figure 21). Remove the clamps and replace the gasket in the gasket extrusion channels of the door. Some force may be required to seat the gasket into the channels. Be sure the gasket corners are seated properly. Figure 19 Right Hand Hinged Door 24" (61 cm) wide appliance 233⁄4" (60.3 cm) 1 ⁄4" (6 mm) Deep 13⁄4" (4.4 cm) 31⁄8" (7.9 cm) 14" (35.6 cm) 47⁄8" (12.4 cm) 13⁄16" (3 cm) 327⁄32" (9.8 cm) ⁄4" (6 mm) radius is permissible 1 31⁄8" (7.9 cm) 31⁄8" (7.9 cm) 3011⁄32" (77.1 cm) This side facing interior #10 x 1/2" screw 15⁄32" (2.9 cm) 111⁄16" (4.3 cm) 41⁄8" (10.5 cm) 2" (5.1 cm) 311⁄16" (9.4 cm) 1" (2.5 cm) diameter x 1⁄4" (6 mm) deep 4 places Figure 20 Right Hand Hinged Door 24" (61 cm) wide appliance 11⁄2" (3.8 cm) typical 17 Figure 21 OVERLAY DOOR PANEL INSTALLATION AND SHELVING CONFIGURATIONS Step 5: Install the door Carefully open the top and bottom hinges on the door being careful as there are many pinch points. Place the hinges over the 4 screws in the cabinet, 2 at the top and 2 at the bottom and slide the door into position. Tighten the 4 hinge screws with a phillips screwdriver. (See Figures 10 and 10a). Place wire harness from the grille and mount to the bottom of the door with the screw and "P" clamp removed in step 1. (See Figure 10b). Reconnect the wire harness, (See Figure 11). Loading Tips and Suggestions Your appliance is equipped with a rollout shelf system which provides maximum access and visibility for the product stored on the shelving arrangements listed below. Step 6: Secure the cabinet Use the #8 x 3⁄4" black screws from the literature pack to secure the counter top to the cabinet top through the holes in the cabinet "Z" bracket. Figure 23 Single Zone Wine Cellar: 15" (38.1 cm) Wide models: Cabinet "Z" bracket (6) 4 bottle tray shelf with vibration dampening mat #8 x 3⁄4" black screws (3 places) Figure 24 Figure 22 Single Zone Wine Cellar: 24" (61 cm) Wide models: 18 (1) 8 bottle tray shelf with vibration dampening mat (2) 7 bottle rollout display rack (1) 5 bottle rollout display rack with vibration dampening mat SHELVING CONFIGURATIONS Figure 27 Dual Zone Wine Cellar: 24" (61 cm) Wide models: Figure 25 Upper Zone: (3) 8 bottle tray shelf with vibration dampening mat Lower Zone: (1) 8 bottle tray shelf with vibration dampening mat (2) 4 bottle half depth tray shelf with vibration dampening mat Single Zone Wine Cellar: 24" (61 cm) Wide models: (5) 8 bottle tray shelf with vibration dampening mat (1) 5 bottle rollout display rack with vibration dampening mat To remove a shelf: ! CAUTION Extend the shelf out of the cabinet until it stops. Unload the shelf. Lift up on the front of the shelf and pull forward to disengage the slide stops. Remove the shelf from the cabinet. (See Figure 26a). Never try to move a loaded shelf, remove everything from the shelf before removing. Use both hands when removing the shelf. Lift up on the front of the shelf Figure 26a Figure 26 19 CARE AND CLEANING AND ENERGY SAVING TIPS Front Grille Be sure that nothing obstructs the required air flow openings in front of the cabinet. At least once or twice a year, brush or vacuum lint and dirt from the front grille area (see page 4). ! CAUTION SHOCK HAZARD: Disconnect electrical power from the appliance before cleaning with soap and water. Cabinet The painted cabinet can be washed with either a mild soap and water and thoroughly rinsed with clear water. NEVER use abrasive scouring cleaners. Interior Wash interior compartment with mild soap and water. Do NOT use an abrasive cleaner, solvent, polish cleaner or undiluted detergent. Care of Appliance 1. Avoid leaning on the door, you may bend the door hinges or tip the appliance. 2. Exercise caution when sweeping, vacuuming or mopping near the front of the appliance. Damage to the grille can occur. 3. Periodically clean the interior of the appliance as needed. 4. Periodically check and/or clean the front grille as needed. In the Event of a Power Failure If a power failure occurs, try to correct it as soon as possible. Minimize the number of door openings while the power is off so as not to adversely affect the appliance's temperature. The following suggestions will minimize the cost of operating your refrigeration appliance. 1. Do not install your appliance next to a hot appliance (cooker, dishwasher, etc.), heating air duct, or other heat sources. 2. Install product out of direct sunlight. 3. Ensure the front grille vents at front of appliance beneath door are not obstructed and kept clean to allow ventilation for the refrigeration system to expel heat. 4. Plug your appliance into a dedicated power circuit. (Not shared with other appliances). 5. When initially loading your new product, or whenever large quantities of warm contents are placed within refrigerated storage compartment, minimize door openings for the next 12 hours to allow contents to pull down to compartment set temperature. 6. Maintaining a relatively full storage compartment will require less appliance run time than an empty compartment. 7. Ensure door closing is not obstructed by contents stored in your appliance. 8. Allow hot items to reach room temperature before placing in product. 9. Minimize door openings and duration of door openings. 10. Use the warmest temperature control set temperature that meets your personal preference and provides the proper storage for your stored contents. 11. When on vacation or away from home for extended periods, set the appliance to warmest acceptable temperature for the stored contents. 12. Set the control to the “off” position if cleaning the appliance requires the door to be open for an extended period of time. 13. For wine storage products: When serving temperatures are not required, return the compartment(s) set temperature to the ideal red and white wine long term storage temperature of 13°C / 55°F. Light assembly replacement All models use LED lamps to illuminate the interior of the appliance. This component is very reliable, but should one fail, contact a qualified service technician for replacement of the LED. 20 DOOR ALIGNMENT AND OBTAINING SERVICE Door alignment for solid and glass door models: The door should be parallel to the sides and top of the appliance. If alignment is necessary the door may be adjusted by loosening the 2 screws which secure the door adjustment bracket on the bottom of the door (see Figure 28a) and adjusting the door side to side. Use a 5⁄32” allen wrench for this procedure. (See Figure 28 below). When finished aligning the door, tighten the screws securely. If Service is Required: • • • • • If the product is within the first year warranty period please contact your dealer or call AGA MARVEL Customer Service at 800.223.3900 for directions on how to obtain warranty coverage in your area. If the product is outside the first year warranty period, AGA MARVEL Customer Service can provide recommendations of service centers in your area. A listing of authorized service centers is also available at www. agamarvel.com under the service and support section. In all correspondence regarding service, be sure to give the service number, serial number, and proof of purchase. Try to have information or description of nature of the problem, how long the appliance has been running, the room temperature, and any additional information that may be helpful in quickly solving the problem. Table "D" is provided for recording pertinent information regarding your product for future reference. For Your Records Date of Purchase Dealer’s name Dealer’s Address Dealer’s City Dealer’s State Dealer’s Zip Code Appliance Serial Number Appliance Service Number Date Warranty Card Sent (Must be within 10 days of purchase). Table D Door should be parallel to top and sides of the appliance. Figure 28 Door adjustment bracket Bottom of door Figure 28a Loosen (don't remove) these two screws. 21 TROUBLESHOOTING Before You Call for Service Problem Appliance not cold enough WARNING ! If the appliance appears to be malfunctioning, read through this manual first. If the problem persists, check the troubleshooting guide below. Locate the problem in the guide and refer to the cause and its remedy before calling for service. The problem may be something very simple that can be solved without a service call. However, it may be required to contact your dealer or a qualified service technician. Electrocution Hazard • Never attempt to repair or perform maintenance on the appliance until the main electrical power has been disconnected. Turning the appliance control "OFF" does not remove electrical power from the unit's wiring. • Replace all parts and panels before operating. Possible Cause • • Control set too warm Content temperature not stabilized. Excessive usage or prolonged door openings. Airflow to front grille blocked. • Door gasket not sealing properly. • Appliance too cold • Control set too cold • (See “Adjusting the Temperature” on page 11) • Door gasket not sealing properly. • No interior light. • Failed LED light assembly or light switch. • Contact a qualified service technician. Light will not go out when door is closed • Display light is turned on. (Glass door models only. Door not activating light switch. • Turn off display light, shut door. • Appliance not level, level appliance, (See page 4, “leveling legs”) Verify the door is aligned properly, refer to page 21 for instructions. Contact a qualified service technician. (See “Adjusting the temperature" on page 11) • • Remedy • • • • • Noise or Vibration Appliance will not run. • Failed light switch • • Appliance not level • • Fan hitting tube obstruction. • • Appliance turned off • • • Power cord not plugged in. No power at outlet. • • 22 Adjust temperature colder. Allow 24 hours for temperature to stabilize. Allow temperature to stabilize for at least 24 hours. Airflow must not be obstructed to front grille. See “clearances” on page 4. Check door alignment and/or replace door gasket. Adjust temperature warmer. Allow 24 hours for temperature to stabilize. Check door alignment and/or replace door gasket. Level appliance, see “Leveling Legs” on page 4. Contact a qualified service technician. Turn appliance on. See “Starting your appliance” on page 10. Plug in power cord. Check house circuit. HOUSEHOLD PRODUCT WARRANTY Entire Product Limited One Year Parts and Labor Warranty Parts or Service Not Supplied or Designated by AGA MARVEL AGA MARVEL warrants that it will supply all necessary parts and labor to repair or replace in the end user’s home or office, any component which proves to be defective in material or workmanship, subject to the condition and exclusions stated below, for a period of one year from the date of purchase by the end user. The above warranties also do not apply if: • • • Additional Second Through Fifth Year Limited Parts Only Warranty The original bill of sale, deliver date, or serial number cannot be verified. Defective parts are not returned for inspection if so requested by AGA MARVEL. The refrigeration equipment is not in the possession of the original end use purchaser. During the four years following expiration of the one year limited warranty, AGA MARVEL will supply replacement parts for the hermetically sealed refrigeration system which consists of the compressor, condenser, drier, accumulator, bypass valve, connecting tubing and the evaporator that are proven to be defective due to workmanship or materials subject to the conditions and exclusions below. The warranties set forth herein are the only warranties extended by AGA MARVEL. Any implied warranties, including the implied warranty of merchantability, are limited to the duration of these express warranties. In no event shall AGA MARVEL be liable for any consequential or incidental damages or expenses resulting from breach of these or any other warranties, whether express or implied. The above warranties do not cover: Some states do not allow the exclusion or limitation of consequential damages or a limitation on how long an implied warranty lasts, so the above exclusion or limitation may not apply to you. This warranty gives you specific legal rights and you may have other rights that may vary from state to state. • • • • Shipping costs of replacement parts or returned defective parts. Customer education or instructions on how to use the appliance. Any content loss due to product failure. Removal or installation of product. No person, firm, or corporation is authorized to make any other warranty or assume any other obligation for AGA MARVEL. These warranties apply only to products used in any of the fifty states of the United States and the District of Columbia. Nor do the above warranties cover failure of this product or its components due to: • • • Transportation or subsequent damages. Commercial use or use other than normal household or small office. Improper installation, misuse, abuse, accident or alteration, use of wiring not conforming to electrical codes, low or high voltages, failure to provide necessary maintenance, or other unreasonable use. To obtain performance of this warranty, report any defects to: 1260 E. VanDeinse St. Greenville MI 48838 Phone: 800.223.3900 23 www.agamarvel.com 1260 E. VanDeinse St. Greenville MI 48838 800.223.3900 41013358-EN Rev E 11/5/14 All specifications and product designs subject to change without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions, replacements or compensation for previously purchased products.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project