Futuro Futuro | WL34FOLIO-BLK | Folio Range Hood Installation Manual | Futuro Futuro WL34FOLIO-BLK Folio Range Hood Installation Manual

Futuro Futuro WL34FOLIO-BLK Folio Range Hood Installation Manual
Futuro Futuro
Folio
Designer Range Hood
Installation & User’s Manual
20”
20.7”
0.4”
Overall Dimensions
33.5”
16”
4.2”
6”
13.75”
14.3”
4.1”
27.6”
Weight: 55 lbs. (25 kg)
Must be attached to
load-bearing component
(joist/frame/plywood),
NOT to bare sheetrock.
General Components Location
6”
6”
Duct Output Collar
Locations:
Top or Rear
.
iam
d
dia
11.3”
15.79”
min. 12”
m.
6”
dia
11.3”
m.
”
3
4.1
Mounting Bracket & Hooks
0.4”
Ducted installation - vertical blower output
Mounting, Part I:
18”
11.3”
It is recommended for the center of the range hood
to be approximately 26” - 28” above the cooktop,
for best capture performance.
1.) Measure 16”-18” from the cooktop to the bottom
of the hood.
2.) Remove the mounting bracket from the hood, position
it on the wall, and ensure it’s level.
3.) Mark the location of the mounting screws. Note that
these LOAD-BEARING screws should be connected to
a stud, framework, or 3/4” plywood - NOT to bare sheetrock.
4.) Attach the bracket to the wall.
Mounting, Part II:
1-3.) Open the bottom panel, if installed, and remove the
metal lters, if present. Locate 2 the security L-brackets on top,
unscrew & remove them.
4.) Hang the range hood on the mounting bracket, making sure
to engage BOTH mounting hooks.
5.) If adjustment is necessary, each mounting hook has 2
adjustment screws - the upper screw (B) controls distance from
wall, the lower screw (C) controls vertical adjustment.
6.) Find the 2 security L-brackets that were removed
during Step 1-3, install them on top of the hood body,
and secure them to the wall.
Backdraft Damper Installation
A backdraft damper is supplied with the range hood.
For DUCTED installation, it’s strongly recommended to DISCARD this damper, and use a damper built into the
end-cap (wall or roof cap).
For DUCTLESS installation: insert the damper as shown into the blower output collar, open the blades, and secure
the damper with the provided screw.4.) Attach the bracket to the wall.
Ducted installation - rear (horizontal) blower output
Mounting, Part I:
18”
11.3”
It is recommended for the center of the range hood
to be approximately 26” - 28” above the cooktop,
for best capture performance.
1.) Measure 16”-18” from the cooktop to the bottom
of the hood.
2.) Remove the mounting bracket from the hood, position
it on the wall, and ensure it’s level.
3.) Mark the location of the mounting screws. Note that
these LOAD-BEARING screws should be connected to
a stud, framework, or 3/4” plywood - NOT to bare sheetrock.
4.) Attach the bracket to the wall.
Mounting, Part II: Blower Removal
1-2.) Remove the indicated screws & remove bottom panel.
3-4.) Remove the indicated screws & remove top panel.
5.) Disconnect the control panel cable from blower.
6.) Disconnect the power cable from the blower.
7.) Disconnect the grounding wire from the hood backplate.
8.) Remove the 6 screws holding the blower.
Blower Motor Removal
Ducted installation - rear (horizontal) blower output
Blower Motor Repositioning
Remove the blower, remove the knock-out plate (1), and re-install the blower in new direction,
repeating the steps described on the previous page in reverse.
Bottom Panel Operation
Filters Installation
Metal Mesh Filters
For ducted AND ductless installation
Carbon (charcoal) Filters
ONLY for DUCTLESS installation
The electric circuit to which the hood is to be connected
must be:
* In compliance with local electrical standards,
* Properly grounded,
* Dedicated, not shared with other appliances or dimmable lights.
The duct (air pipe) must have:
* A diameter of 6” throughout its entire run, including the end-cap (roof or wall cap).
* A slight slope downward in horizontal sections - to prevent condensation from
dripping back into the blower motor.
* Minimum number of angles & elbows, to minimize turbulence and loss of suction.
* Minimum required length to avoid vibrations / turbulence, which can affect
the performance of the hood as well as user’s comfort level.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising