ELICA | EMZ630S2 | Install Instructions Mezzano | Elica EMZ630S2 Install Instructions Mezzano

Use, Care, and Installation Guide
READ AND SAVE THESE INSTRUCTIONS
EN
Contents
page
1
English
Contents
Important safety Notice..............................................................................................................................................3
Electrical & Installation requirements ......................................................................................................................4
Electrical requirements ........................................................................................................................................................................................ 4
Before installing the hood .................................................................................................................................................................................... 4
List of Materials...........................................................................................................................................................5
Parts supplied ...................................................................................................................................................................................................... 5
Parts not supplied ................................................................................................................................................................................................ 5
Ducting Options and Examples.................................................................................................................................7
Venting methods .................................................................................................................................................................................................. 7
Preparation .......................................................................................................................................................................................................... 7
Installation ...................................................................................................................................................................8
Installation - Ducting version................................................................................................................................................................................ 8
Installation - Ductless (Recirculating) version .................................................................................................................................................... 12
Description of the hood & Controls ........................................................................................................................16
Controls.............................................................................................................................................................................................................. 17
Maintenance ..............................................................................................................................................................19
Cleaning............................................................................................................................................................................................................. 19
Grease Filter ...................................................................................................................................................................................................... 19
Replacing the light bulb...................................................................................................................................................................................... 19
Charcoal Filter.................................................................................................................................................................................................... 20
APPROVED FOR RESIDENTIAL APPLIANCES
FOR RESIDENTIAL USE ONLY
READ AND SAVE THESE INSTRUCTIONS
PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING.
INSTALLATION MUST COMPLY WITH ALL LOCAL CODES.
IMPORTANT: Save these Instructions for the Local Electrical Inspector’s use.
INSTALLER: Please leave these Instructions with this unit for the owner.
OWNER: Please retain these instructions for future reference.
Safety Warning: Turn off power circuit at service panel and lock out panel, before wiring this appliance.
Requirement: 120 V AC, 60 Hz. 15 or 20 A Branch Circuit
READ AND SAVE THESE INSTRUCTIONS
Important safety Notice
WARNING
CAUTION
TO REDUCE THE RISK OF INJURY TO PERSONS, IN
THE EVENT OF A RANGE TOP GREASE FIRE,
OBSERVE THE FOLLOWING:
a) SMOTHER FLAMES with a close-fitting lid, cookie
sheet, or other metal tray, then turn off the gas burner or
the electric element. BE CAREFUL TO PREVENT
BURNS. If the flames do not go out immediately,
EVACUATE AND CALL THE FIRE DEPARTMENT.
b) NEVER PICK UP A FLAMING PAN - you may be
burned.
c) DO NOT USE WATER, including wet dishcloths or
towels - a violent steam explosion will result.
d) Use an extinguisher ONLY if:
1) You know you have a class ABC extinguisher,
and you already know how to operate it.
2) The fire is small and contained in the area where
it started.
3) The fire department is being called.
4) You can fight the fire with your back to an exit.
FOR GENERAL VENTILATING USE ONLY. DO NOT USE
TO
EXHAUST
HAZARDOUS
OR
EXPLOSIVE
MATERIALS OR VAPORS.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS, OBSERVE THE FOLLOWING:
A. Use this unit only in the manner intended by the
manufacturer.
If you have questions, contact the
manufacturer.
B. Before servicing or cleaning the unit, switch power off at
service panel and lock service panel disconnecting
means to prevent power from being switched on
accidentally. When the service disconnecting means
cannot be locked, securely fasten a prominent warning
device, such as a tag, to the service panel.
C. Installation Work and Electrical Wiring Must Be Done By
Qualified Person(s) In Accordance With All Applicable
Codes & Standards, Including Fire-rated Construction.
D. Sufficient air is needed for proper combustion and
exhausting of gases through the flue (Chimney) of fuel
burning equipment to prevent back- drafting. Follow the
heating equipment manufacturers guideline and safety
standards such as those published by the National Fire
Protection Association (NFPA), the American Society for
Heating, Refrigeration and Air Conditioning Engineers
(ASHRAE), and the local code authorities.
E. When cutting or drilling into wall or ceiling, do not
damage electrical wiring and other hidden utilities.
F. Ducted systems must always be vented to the outdoors.
OPERATION
a. Always leave safety grills and filters in place. Without
these components, operating blowers could catch onto hair,
fingers and loose clothing.
The manufacturer declines all responsibility in the event of
failure to observe the instructions given here for installation,
maintenance and suitable use of the product. The
manufacturer further declines all responsibility for injury due
to negligence and the warranty of the unit automatically
expires due to improper maintenance.
CAUTION
To reduce risk of fire and to properly exhaust air, be
sure to duct air outside - do not vent exhaust air into
spaces within walls, ceilings, attics, crawl spaces, or
garages.
WARNING
TO REDUCE THE RISK OF FIRE, USE ONLY METAL
DUCT WORK.
Install this hood in accordance with all requirements
specified.
WARNING
To Reduce The Risk Of Fire Or Electric Shock, Do Not
Use This Hood With Any External Solid State Speed
Control Device.
WARNING
TO REDUCE THE RISK OF A RANGE TOP GREASE
FIRE.
a) Never leave surface units unattended at high settings.
Boilovers cause smoking and greasy spillovers that may
ignite. Heat oils slowly on low or medium settings.
b) Always turn hood ON when cooking at high heat or when
flambeing food (I.e. Crepes Suzette, Cherries Jubilee,
Peppercorn Beef Flambe’).
c) Clean ventilating fans frequently. Grease should not be
allowed to accumulate on fan or filter.
d) Use proper pan size. Always use cookware appropriate
for the size of the surface element.
3
Electrical & Installation requirements
Electrical requirements
Before installing the hood
IMPORTANT
1. For the most efficient air flow exhaust, use a straight run
or as few elbows as possible.
CAUTION: Vent unit to outside of building, only.
Observe all governing codes and ordinances.
It is the customer’s responsibility:
To contact a qualified electrical installer.
To assure that the electrical installation is adequate and in
conformance with National Electrical Code, ANSI/NFPA 70
— latest edition*, or CSA Standards C22.1-94, Canadian
Electrical Code, Part 1 and C22.2 No.0-M91 - latest
edition** and all local codes and ordinances.
2. At least two people are necessary for installation.
3. The hood is fitted with Screws and Drywall Anchors
suitable for most surfaces, consult a Qualified Installer,
check if they perfectly fit with your cabinet/wall.
4. Do not use flex ducting.
If codes permit and a separate ground wire is used, it is
recommended that a qualified electrician determine that the
ground path is adequate.
5. COLD WEATHER installations should have an additional
backdraft damper installed to minimize backward cold air
flow and a nonmetallic thermal break to minimize
conduction of outside temperatures as part of the
ductwork. The damper should be on the cold air side of
the thermal break.
The break should be as close as possible to where the
ducting enters the heated portion of the house.
Do not ground to a gas pipe.
Check with a qualified electrician if you are not sure range
hood is properly grounded.
Do not have a fuse in the neutral or ground circuit.
IMPORTANT
6. Make up air: Local building codes may require the use of
Make-Up Air Systems when using Ducted Ventilation
Systems greater than specified CFM of air movement.
The specified CFM varies from locale to locale. Consult
your HVAC professional for specific requirements in your
area.
Removing the packaging
Save Installation Instructions for electrical inspector’s use.
The range hood must be connected with copper wire only.
The range hood should be connected directly to the fused
disconnect (Or circuit breaker) box through metal electrical
conduit.
CAUTION!
Remove carton carefully, Wear gloves to protect against
sharp edges.
Wire sizes must conform to the requirements of the National
Electrical Code ANSI/NFPA 70 — latest edition*, or CSA
Standards C22.1-94, Canadian Electrical Code Part 1 and
C22.2 No. 0-M91 - latest edition** and all local codes and
ordinances.
WARNING!
Remove the protective film covering the product before
putting into operation.
A U.L.- or C.S.A.-listed conduit connector must be provided
at each end of the power supply conduit (at the range hood
and at the junction box).
Copies of the standards listed may be obtained from:
* National Fire Protection Association Batterymarch Park Quincy,
Massachusetts 02269
** CSA International 8501 East Pleasant Valley Road Cleveland,
Ohio 44131-5575
4
List of Materials
Parts supplied
Parts not supplied
Removing the packaging
Optional Accessories
CAUTION!
Remove carton carefully, Wear gloves to protect against
sharp edges.
•
WARNING!
Remove the protective film covering the product before
putting into operation.
• Hood canopy assembly with blower, transition.
• Lamp already installed.
• Grease filter.
• Duct cover.
• Hardware bag with:
• Plastic Gasket.
• Template.
• Duct cover support bracket (1 piece)
• Use, care and installation guide
• Glass bracket (2 pieces)
• Wood screws (6 pieces - 3/16" x 1" 3/4)
• Hood attachment anchors screws (6 pieces - 1/8" x
3/8")
• Assembly screws (8 pieces)
Ductless Recirculating Kit
To be used only in the Ductless (Recirculating)
version
includes: charcoal filter, charcoal filter support and
fixing bracket, deflector
Optional Accessories
•
Ductless Recirculating Kit
To be used only in the Ductless (Recirculating)
version
includes: charcoal filter, charcoal filter support and
fixing bracket, deflector
Tools/Materials required
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
5
Wire nuts
Tape to mount template
8" rounded metal duct length to suit installation
Measuring tape
Pliers
Gloves
Knife
Safety glasses
Electric drill with 5/16” and 3/8” Bits
Strain relief
Spirit level
Duct tape
Screwdrivers:
Phillips (Posidrive) # 2
Torx # 2
Wire cutter/stripper
Masking tape
Hammer
Saw, jig saw or reciprocating saw
6
Ducting Options and Examples
Closely follow the instructions set out in this manual.
All responsibility, for any eventual inconveniences, damages or fires caused by not complying with the instructions in this
manual, is declined.
Venting methods
The hood is equipped with a transition B for discharge of fumes to the outside (Ducting version).
Should it not be possible to discharge cooking fumes and vapour to the outside, the hood can be used in the Ductless
(Recirculating) version. Attach a charcoal filter and the deflector F on the duct cover support bracket G. Fumes and vapors
are recycled through the top grille H by means of a duct connected to the transition B and the transition mounted on the
deflector F.
NOTE: For ductless (Recirculating) version only: purchase the Ductless Recirculating Kit.
Minimum Duct Size (Ducting/Ductless version): 8" Round Pipe.
Preparation
Do not cut a joist or stud unless absolutely necessary. If a joist or stud must be cut, then a supporting frame must be
constructed.
Fittings material is provided to secure the hood to most types of walls/ceilings.
However, a qualified technician must verify suitability of the materials in accordance with the type of wall/ceiling.
Before making cutouts, make sure there is proper clearance within the ceiling or wall for exhaust vent.
Hood installation height above cooktop is the users preference. The lower the hood is above the cooktop, the more efficient the
capturing of cooking odors, grease and smoke.
The hood shall be installed at 24" minimum to 32" above the countertop.
Check your ceiling height and the hood height maximum before you select your hood.
7
Installation
Installation - Ducting version
•
If possible, disconnect and move freestanding or slide-in
range from cabinet opening to provide easier access to
rear wall. Otherwise put a thick, protective covering over
countertop, cooktop or range to protect from damage
and debris. Select a flat surface for assembling the unit.
Cover that surface with a protective covering and place
all canopy hood parts and hardware in it.
•
Determine and mark the centerline on the wall where the
canopy hood will be installed.
•
Select a mounting height comfortable for the user and
mark on wall.
•
Tape template, matching center-line and hood bottom.
Wall ducting
If ductwork will vent to rear:
Note: for minimum duct cover extension we suggest to use
a round to rectangle duct adapter.
• Use a level to draw a line straight up from the centerline
on the template.
• Measure at least 26 - 1/4" (the measure might vary
dependig on the elbow used) above the pencil line that
indicates the bottom installation height, to the circle
center of an 8-½” diameter duct hole (Hole may be
elongated for duct elbow).
House wiring location
• The junction box is located on the top left side of the
hood.
• Wiring should enter the back wall at least 20 - 1/4"
above the bottom of the installation height, and within 75/8" and 4-7/8"of the left side of the centerline.
Mounting the duct cover bracket
The duct bracket should be installed against the back wall
and flush with the ceiling.
This bracket will hold the telescopic duct cover in place at
the top.
Secure the bracket to the wall:
• Align the marked centerline on the bracket with the
centerline on the wall.
• Mark 2 screw hole locations in the wall.
• Drill 5/16" pilot holes in the marked locations.
• Install wall fastener anchors.
• Drive wood screws, by hand, into the fastener to allow
anchors to expand. Remove the screws.
• Secure the bracket to the wall with wood screws and/or
fasteners.
Ceiling ducting
If the duct will vent straight up to the ceiling:
• Use level to draw a line straight up, from the centerline
on the template to the ceiling.
• Measure at least 4 -3/4 ” from the back wall to the circle
center of an 8-½” hole on the ceiling.
8
Install framing for hood support
•
Mark “lower” wood screw holes locations in the wall
using a pencil.
•
•
•
•
•
Remove the hood.
Drive “lower” wood screws, by hand. Remove screws.
Mount the hood onto the “upper” screws.
Drive and tighten the “upper” wood screws, by hand.
Drive and tighten the “lower” wood screws, by hand.
•
If drywall is present, mark the screw hole locations.
Remove the template.
• Cut away enough drywall to expose 2 vertical studs at
the holes location indicated by the template.
Install two horizontal supports at least 4" X 2" between
two wall studs at the bottom and upper mounting holes
installation location.
• The horizontal support must be flush with the room side
of the studs.
Use cleats behind both sides of the support to secure to
wall studs.
• Reinstall drywall and refinish.
IMPORTANT- Framing must be capable of supporting
100 lbs.
Mounting the hood
WARNING: 2 people are required to lift and position the
hood onto the mounting screws.
• Place the template on the wall along the horizontal line,
make sure the template is leveled and centered with the
centerline.
• Mark “upper” screw holes locations in the wall.
• IMPORTANT. Check to be sure that hole locations are
leveled and correctly centered by the vertical centerline.
• Drive “upper” wood screws by hand. Leave ¼ “ of
distance between the screw head and the wall.
• Remove the grease filter and mount the hood onto the
“upper” screws.
Connecting the ductwork
• Install ductwork, making connections in the direction of
airflow as illustrated.
• Push duct over the exhaust outlet.
• Wrap all duct joints and the flange connections with duct
tape for an airtight seal.
• Make the same connection in the wall or ceiling vent
exit.
Electrical connection
WARNING
Electrical Shock Hazard
Warning: Turn off power circuit at the service panel
before wiring this unit.
9
120 VAC, 15 or 20 Amp circuit required.
Mounting the duct cover
•
•
•
ELECTRICAL GROUNDING INSTRUCTIONS
THIS APPLIANCE IS FITTED WITH AN ELECTRICAL
JUNCTION BOX WITH 3 WIRES, ONE OF WHICH
(GREEN/YELLOW) SERVES TO GROUND THE
APPLIANCE. TO PROTECT YOU AGAINST
ELECTRIC SHOCK, THE GREEN AND YELLOW WIRE
MUST BE CONNECTED TO THE GROUNDING WIRE
IN YOUR HOME ELECTRICAL SYSTEM, AND IT
MUST UNDER NO CIRCUMSTANCES BE CUT OR
REMOVED.
Failure to do so can result in death or electrical
shock.
•
Position the duct cover over the mounted hood.
Slide the bottom of the duct into the canopy area.
Position the top of the duct over the duct mounting
bracket. If a telescopic duct cover is used, grab the
upper part of the telescopic duct cover, pull it and place
it in the duct cover mounting bracket.
Secure the top of the duct with 2 assembly screws
provided.
Facing the front of the range hood, remove the left
knockout and the Junction box cover and install the
conduit connector (cULus listed) in junction box.
•
•
If not already done, install 1/2” conduit connector in jbox.
Secure the bottom of the duct with 2 assembly screws
provided.
Install the grease filter and turn power on at service panel.
Check operation of the hood.
10
If range hood does not operate:
•
•
Check that the circuit breaker is not tripped or the house
fuse blown.
Disconnect power supply. Check that wiring is correct.
• Check that the internal General ON/OFF Push button
Switch is switched ON.
To get the most efficient use from your new range hood,
read the “Use and Care Information” section.
Keep your Installation Instructions and Use and Care
Guide close to range hood for easy reference.
11
Installation - Ductless (Recirculating) version
Install framing for hood support
CAUTION
To install the hood in this version, first purchase the
Ductless Recirculating Kit.
includes: charcoal filter and deflector
•
If possible, disconnect and move freestanding or slide-in
range from cabinet opening to provide easier access to
rear wall. Otherwise put a thick, protective covering over
countertop, cooktop or range to protect from damage
and debris. Select a flat surface for assembling the unit.
Cover that surface with a protective covering and place
all canopy hood parts and hardware in it.
•
Determine and mark the centerline on the wall where the
canopy hood will be installed.
•
Select a mounting height comfortable for the user and
mark on wall.
•
Tape template, matching center-line and hood bottom.
•
If drywall is present, mark the screw hole locations.
Remove the template.
• Cut away enough drywall to expose 2 vertical studs at
the holes location indicated by the template.
Install two horizontal supports at least 4" X 2" between
two wall studs at the bottom and upper mounting holes
installation location.
• The horizontal support must be flush with the room side
of the studs.
Use cleats behind both sides of the support to secure to
wall studs.
• Reinstall drywall and refinish.
IMPORTANT- Framing must be capable of supporting
100 lbs.
Mounting the duct cover bracket
The duct bracket should be installed against the back wall
and flush with the ceiling.
This bracket will hold the telescopic duct cover in place at
the top.
Secure the bracket to the wall:
• Align the marked centerline on the bracket with the
centerline on the wall.
• Mark 2 screw hole locations in the wall.
• Drill 5/16" pilot holes in the marked locations.
• Install wall fastener anchors.
• Drive wood screws, by hand, into the fastener to allow
anchors to expand. Remove the screws.
• Secure the bracket to the wall with wood screws and/or
fasteners.
House wiring location
• The junction box is located on the top left side of the
hood.
• Wiring should enter the back wall at least 20 - 1/4" above
the bottom of the installation height, and within 7-5/8"
and 4-7/8"of the left side of the centerline.
12
Mounting the hood
WARNING: 2 people are required to lift and position the
hood onto the mounting screws.
• Place the template on the wall along the horizontal line,
make sure the template is leveled and centered with the
centerline.
• Mark “upper” screw holes locations in the wall.
• IMPORTANT. Check to be sure that hole locations are
leveled and correctly centered by the vertical centerline.
• Drive “upper” wood screws by hand. Leave ¼ “ of
distance between the screw head and the wall.
• Remove the grease filter and mount the hood onto the
“upper” screws.
•
•
•
•
•
Remove the hood.
Drive “lower” wood screws, by hand. Remove screws.
Mount the hood onto the “upper” screws.
Drive and tighten the “upper” wood screws, by hand.
Drive and tighten the “lower” wood screws, by hand.
Air deflector installation
• Assemble the air deflector with the duct cover bracket
with 4 assembly screws provided as shown.
•
Mark “lower” wood screw holes locations in the wall
using a pencil.
13
•
Measure from the bottom of the air deflector to the
bottom of the hood outlet, as shown.
•
•
Cut the duct at the measured size.
Uninstall the air deflector removing the 4 assembly
•
•
•
screws.
Slip the duct onto the bottom of the deflector.
Place the assembled deflector and duct over the exhaust
outlet from the hood.
Assemble the air deflector to the duct cover bracket with
4 assembly screws provided as shown.
Electrical connection
WARNING
Electrical Shock Hazard
Warning: Turn off power circuit at the service panel
before wiring this unit.
120 VAC, 15 or 20 Amp circuit required.
ELECTRICAL GROUNDING INSTRUCTIONS
THIS APPLIANCE IS FITTED WITH AN ELECTRICAL
JUNCTION BOX WITH 3 WIRES, ONE OF WHICH
(GREEN/YELLOW) SERVES TO GROUND THE
APPLIANCE. TO PROTECT YOU AGAINST
ELECTRIC SHOCK, THE GREEN AND YELLOW WIRE
MUST BE CONNECTED TO THE GROUNDING WIRE
IN YOUR HOME ELECTRICAL SYSTEM, AND IT
MUST UNDER NO CIRCUMSTANCES BE CUT OR
REMOVED.
Failure to do so can result in death or electrical
shock.
Mounting the duct cover
•
•
•
Facing the front of the range hood, remove the left
knockout and the Junction box cover and install the
conduit connector (cULus listed) in junction box.
•
•
If not already done, install 1/2” conduit connector in jbox.
14
Position the duct cover over the mounted hood.
Slide the bottom of the duct into the canopy area.
Position the top of the duct over the duct mounting
bracket. If a telescopic duct cover is used, grab the
upper part of the telescopic duct cover, pull it and place
it in the duct cover mounting bracket.
Secure the top of the duct with 2 assembly screws
provided.
•
Secure the bottom of the duct with 2 assembly screws
provided.
Install the charcoal filter on the back side of the grease filter,
install both on the range hood and turn power on at service
panel. Check operation of the hood.
If range hood does not operate:
•
Check that the circuit breaker is not tripped or the house
fuse blown.
• Disconnect power supply. Check that wiring is correct.
• Check that the internal General ON/OFF Push button
Switch is switched ON.
To get the most efficient use from your new range hood,
read the “Use and Care Information” section.
Keep your Installation Instructions and Use and Care
Guide close to range hood for easy reference.
15
Description of the hood & Controls
1.
2.
3.
4.
5.
6.
7.
Blower and light controls
Lamp housings
Grease filter Handle
Grease filter
Canopy
Duct covers
Louver holes (Only for Recirculating version)
16
•
This button is used to increase the fan speed, or turn
ON the fan.
• The fan will turn ON if the “+” button is pressed and
the hood was OFF.
• If the fan is at first speed and the “+” button is
pressed, the fan will be set to second speed.
• If the fan is at second speed and the “+” button is
pressed, the fan will be set to third speed.
• If the fan is at third speed and the “+” button is
pressed, the fan will be set to fourth speed.
• If the fan is at fourth speed and the “+” button is
pressed, a beep will sound.
Clock programming
Controls
Use the high suction speed in cases of concentrated kitchen
vapours. It is recommended that the cooker hood suction is
switched on for 5 minutes prior to cooking and to leave in
operation during cooking and for another 15 minutes
approximately after terminating cooking.
Note: Hood retains last speed setting when aspiration
switch is turned off.
Description of control panel
•
The clock can be reprogrammed at any time except
during an active timed function.
• The clock can be displayed in a twelve hour format and
valid clock times are from 1:00 to 12:59.
• The clock can be reprogrammed pressing the “Timer”
button for 3 seconds, and after, the clock can be
adjusted with the “+” and “-” buttons. Colon “:” will flash
indicating clock programming mode.
• The user can have minute increments / decrements of 1
minute, but if the user keep pressing the “+” / ”-” buttons
for more than 1 second, the increments / decrements will
be of 5 minutes.
During this option the control will round to the nearest 5
minutes.
• The user can finish on reprogramming the clock pressing
the “Timer” button.
• After 1 minute of no button pressed the control will
accept the programmed clock time and will add one
minute to the set clock.
Grease filter saturation alarm (Optional)
1. Light Button
•
Press lamp button to turn ON the light on High
Intensity (Lamp state previously OFF).
• Press lamp button to turn ON the light on Low
Intensity (Lamp state previously ON).
• Press lamp button to turn OFF the light (Lamp state
previously ON).
2. Timer Button
•
The default timer setting is 10 minutes, and it can be
adjusted between 60 minutes and 1 minute.
• After pressing the timer button, the control enters to a
timer setup mode, and user can adjust the timer
countdown time with the “+” and “-” buttons within 5
seconds. The timer can be initiated immediately
pressing the timer button, after setting the timer
duration or pressing the timer button twice (default 10
minutes setting).
• If no action occurs within 5 seconds, the countdown
will start.
• During the timer setup the “+” and “-” buttons are
dedicated to the timer and no motor action will occur.
• Once the timer is initiated, it can be cancelled by
pressing the timer button again.
3. Display
•
•
After thirty fan functional hours, the display will show
“Grease Filter” if the fan is active.
When this icon is shown in the display, the grease filters
installed are required to be washed.
To reset the grease filter saturation alarm the user must
press the “+” button for 5 seconds, after this action the
icon “Grease filter” is not displayed, and the hood has
the normal display operation.
Charcoal filter saturation alarm (Optional)
•
After one hundred and twenty functional hours of the fan,
the display will show “Charcoal Filter” if the fan is
active. When this icon flashes on display, the charcoal
filters installed are required to be replaced or
reactivated.
• To reset the charcoal filter saturation indication the user
must press the “-” button for 5 seconds, after this time
the icon “Charcoal filter” is not displayed and the hood
has the normal display operation.
Audible signal activation and deactivation
• Shows the hood settings.
4. “-” Button. Speed Decrease / OFF
•
This button is used to decrease the fan speed, or
turn OFF the fan.
• The fan will turn OFF if the “-” button is pressed and
the hood was in the first speed.
• If the fan is at second speed and the “-” button is
pressed, the fan will be set to first speed.
• If the fan is at third speed and the “-” key is pressed,
the fan will be set to second speed.
• If the fan is at fourth speed and the “-” button is
pressed, the fan will be set to third speed.
• If the fan is OFF and the “-” button is pressed, the
control backlight will light up.
5. “+” Button. Speed Increase / ON
•
The audible signals can be activated or deactivated
pressing the “Light” button for 5 seconds.
• If the audible signal is activated, a tone must sound and
the “Snd” symbol must appear on the display for 3
seconds.
• If the audible signal is deactivated, the “Snd” symbol
must appear on the display for 3 seconds and no tone
must sound.
Charcoal filter inclusion and exclusion (Recirculating
accessories)
•
17
The charcoal filter inclusion or exclusion can be set by
pressing the “+” and “-” buttons at the same time for 5
seconds.
•
The Inclusion or exclusion of charcoal filter must be
selected while the lamps and the motor are OFF.
• When the charcoal filter has been excluded, the charcoal
filter alarm is disabled.
Heat sensor
•
•
•
•
The control is equipped with a heat sensor that will turn
on the blower at second speed if excessive heat occurs
(over 158° F or 70°C) surrounding the control area.
If the blower is OFF or if it is operating at first or second
speed, the blower will be set automatically to third
speed, the display shows the word "CArE" to indicate
that heat sensor has detected an excessive heat.
During this state, the user may raise the blower speed to
fourth speed but can not decrease the speed.
When the temperature level on the hood drops to
normal, the blower will operate in the setting defined by
the user before the alarm occured.
18
Maintenance
ATTENTION! Before performing any maintenance operation, isolate the hood from the electrical supply by switching off at the connector and removing the connector fuse.
Or if the appliance has been connected through a plug and socket, then the plug must be removed from the socket.
Cleaning
The cooker hood should be cleaned regularly (at least with the same frequency
with which you carry out maintenance of the fat filters) internally and externally.
Clean using the cloth dampened with neutral liquid detergent. Do not use abrasive
products. DO NOT USE ALCOHOL!
Warning:
Failure to carry out the basic cleaning recommendations of the cooker hood and
replacement of the filters may cause fire risks.
Therefore, we recommend oserving these instructions.
The manufacturer declines all responsibility for any damage to the motor or any
fire damage linked to inappropriate maintenance or failure to observe the above
safety recommendations.
Replacing the light bulb
CAUTION
Before replacing the lamps, switch power off at service
panel and lock service panel disconnecting means to
prevent power from being switched on accidentally.
NOTE: Turn off the lights and fan. Allow the lights to
cool before handling. If new lights do not operate be
sure lights are inserted correctly before calling service.
Grease Filter
Traps cooking grease particles.
This must be cleaned once a month using non aggressive detergents, either by
hand or in the dishwasher, which must be set to a low temperature and a short
cycle. When washed in a dishwasher, the grease filter may discolour slightly, but
this does not affect its filtering capacity.
To remove the grease filter, pull the spring release handle.
Replace Lights
• Remove the inner lamp lens cover by inserting a small
flat blade screwdriver into each of the three slots and
gently prying it free.
NOTE: Do not remove the outer trim ring (lamp
assembly).
• Grasp the bulb and pull it straight out.
• Replace with 12 volt, 20 watt halogen bulbs with a G4
base SUITABLE FOR USE IN OPEN LUMINAIRES.
Follow package directions, wear gloves, do not
touch bulb with your bare fingers.
• Replace inner cover by inserting the three retaining tabs
into the three slots and pressing them firmly in place.
19
Charcoal Filter
If the model is not vented to the outside, the air will be
recirculated through disposable charcoal filters that help
remove smoke and odors.
The charcoal filters cannot be cleaned.
They must be replaced.
The charcoal filters are clipped inside of each metal grease
filter.
The charcoal filters should be replaced every 4-6 months
(depending on hood usage).
NOTE: DO NOT rinse, or put charcoal filters in an automatic
dishwasher.
NOTE: Charcoal filters are not included with the hood.
They must be ordered from your supplier.
Order the needed kit specifying your hood model and width
size.
20
Download PDF

advertising