ELICA | EAI430SS | Installation instructions | Elica ECM630S3 Installation Instructions

Elica ECM630S3 Installation Instructions
Use, Care, and
Installation Guide
Guide
d’utilisation,
d’entretien et
d’installation
Guía de
instalación, uso y
mantenimiento
READ AND SAVE THESE
INSTRUCTIONS
LISEZ CES
INSTRUCTIONS ET
CONSERVEZ-LES
Models:
EAI430SS
EAI436SS
LEA Y CONSERVE
ESTAS INSTRUCCIONES
LIB0131463
Printed in Mexico
1
ENGLISH
Contents
Important safety notice................................................................................................................................................................................................. 3
Electrical & installation requirements ................................................................................................................................................................ 4
Before installing the hood ...................................................................................................................................................................................... 4
Dimensions and clearances......................................................................................................................................................................................... 4
List of materials.................................................................................................................................................................................................................5
Parts supplied .............................................................................................................................................................................................................. 5
Parts not supplied ...................................................................................................................................................................................................... 5
Ducting options and examples.................................................................................................................................................................................. 6
Installation ......................................................................................................................................................................................................................... 7
Electrical connection................................................................................................................................................................................................ 9
Complete the installation........................................................................................................................................................................................ 9
Description of the hood................................................................................................................................................................................................. 9
Control.................................................................................................................................................................................................................................. 10
Maintenance ...................................................................................................................................................................................................................... 10
Warranty ........................................................................................................................................................................................................................... 12
APPROVED FOR RESIDENTIAL APPLIANCES
FOR RESIDENTIAL USE ONLY
READ AND SAVE THESE INSTRUCTIONS
PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING.
INSTALLATION MUST COMPLY WITH ALL LOCAL CODES.
IMPORTANT: Save these Instructions for the Local Electrical Inspector’s use.
INSTALLER: Please leave these Instructions with this unit for the owner.
OWNER: Please retain these instructions for future reference.
Safety Warning: Turn off power circuit at service panel and lock out panel, before wiring this appliance.
Requirement: 120 V AC, 60 Hz. 15 or 20 A Branch Circuit.
2
I IMPORTANT SAFETY NOTICE
I CAUTION
IWARNING
IWARNING
b) Always turn hood ON when cooking at high heat or when
flambeing food (I.e. Crepes Suzette, Cherries Jubilee,
Peppercorn Beef Flambe’).
FOR GENERAL VENTILATING USE ONLY. DO NOT USE TO
EXHAUST HAZARDOUS OR EXPLOSIVE MATERIALS OR
VAPOURS.
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS, OBSERVE THE FOLLOWING:
A. Use this unit only in the manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
B. Before servicing or cleaning the unit, switch power off
at service panel and lock service panel disconnecting
means to prevent power from being switched on
accidentally.
When the service disconnecting means cannot be
locked, securely fasten a prominent warning device,
such as a tag, to the service panel.
C. Installation work and electrical wiring must be done by
qualified person(s) in accordance with all applicable
codes & standards, including fire-rated construction.
D. Sufficient air is needed for proper combustion and
exhausting of gases through the flue (Chimney) of fuel
burning equipment to prevent back- drafting.
Follow the heating equipment manufacturers guideline
and safety standards such as those published by the
national fire protection association (NFPA), the american
society for heating, refrigeration and air conditioning
engineers (ASHRAE), and the local code authorities.
E. When cutting or drilling into wall or ceiling, do not
damage electrical wiring and other hidden utilities.
F. Ducted systems must always be vented to the outdoors.
I CAUTION
To reduce risk of fire and to properly exhaust air, be sure to
duct air outside - do not vent exhaust air into spaces within
walls, ceilings, attics, crawl spaces, or garages.
TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE.
a) Never leave surface units unattended at high settings.
Boilovers cause smoking and greasy spillovers that may
ignite. Heat oils slowly on low or medium settings.
c) Clean ventilating fans frequently. Grease should not be
allowed to accumulate on fan or filter.
d) Use proper pan size. Always use cookware appropriate
for the size of the surface element.
IWARNING
TO REDUCE THE RISK OF INJURY TO PERSONS, IN THE
EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE
FOLLOWING:a
a) SMOTHER FLAMES with a close-fitting lid, cookie sheet,
or other metal tray, then turn off the gas burner or the
electric element. BE CAREFUL TO PREVENT BURNS. If the
flames do not go out immediately, EVACUATE AND CALL
THE FIRE DEPARTMENT.
b) NEVER PICK UP A FLAMING PAN - you may be burned.
c) DO NOT USE WATER, including wet dishcloths or towels a violent steam explosion will result.
d) Use an extinguisher ONLY if:
1)
You know you have a class ABC extinguisher, and
you already know how to operate it.
2) The fire is small and contained in the area where it
started.
3) The fire department is being called.
4) You can fight the fire with your back to an exit.
e) Ducted fans must always be vented to the outdoor.
aBased on “Kitchen Fire Safety Tips” published by NFPA.
IWARNING
TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCT
WORK.
Install this hood in accordance with all requirements specified.
IWARNING
To reduce the risk of fire or electric shock, do not use this
hood with any external solid state speed control device.
3
ELECTRICAL & INSTALLATION REQUIREMENTS
IMPORTANT
Copies of the standards listed may be obtained from:
* National Fire Protection Association Batterymarch Park Quincy,
Massachusetts 02269
** CSA International 8501 East Pleasant Valley Road Cleveland,
Ohio 44131-5575
Observe all governing codes and ordinances.
It is the customer’s responsibility:
• To contact a qualified electrical installer.
•
To assure that the electrical installation is adequate and in
conformance with National Electrical Code, ANSI/NFPA 70
— latest edition*, or CSA Standards C22.1-94, Canadian
Electrical Code, Part 1 and C22.2 No.0-M91-latest edition**
and all local codes and ordinances.
•
If codes permit and a separate ground wire is used, it is
recommended that a qualified electrician determine that
the ground path is adequate.
•
Do not ground to a gas pipe.
•
Check with a qualified electrician if you are not sure range
hood is properly grounded.
•
Do not have a fuse in the neutral or ground circuit.
BEFORE INSTALLING THE HOOD
1
2
3
4
5
IMPORTANT
•
Save Installation Instructions for electrical inspector’s use.
•
The range hood must be connected with copper wire only.
•
The range hood should be connected directly to the fused
disconnect (Or circuit breaker) box through metal
electrical conduit.
•
Wire sizes must conform to the requirements of the
National Electrical Code ANSI/NFPA 70 — latest edition*,
or CSA Standards C22.1-94, Canadian Electrical Code Part
1 and C22.2 No. 0-M91 - latest edition** and all local codes
and ordinances.
•
A U.L.- or C.S.A.-listed conduit connector must be
provided at each end of the power supply conduit (at the
range hood and at the junction box).
6
For the most efficient air flow exhaust, use a straight run
or as few elbows as possible.
CAUTION: Vent unit to outside of building, only.
At least two people are necessary for installation.
Fittings material is provided to secure the hood to most
types of walls/ceilings, consult a Qualified Installer,
check if they perfectly fit with your cabinet/wall.
Do not use flex ducting.
COLD WEATHER installations should have an additional
backdraft damper installed to minimize backward cold air
flow and a nonmetallic thermal break to minimize
conduction of outside temperatures as part of the
ductwork. The damper should be on the cold air side of
the thermal break.
The break should be as close as possible to where the
ducting enters the heated portion of the house.
Make up air: Local building codes may require the use of
Make-Up Air Systems when using Ducted Ventilation
Systems greater than specified CFM of air movement.
The specified CFM varies from locale to locale. Consult
your HVAC professional for specific requirements in your
area.
DIMENSIONS AND CLEARANCES
Models
F
E
A
EAI430SS
EAI436SS
30” (76.2 cm)
36” (91.4 cm)
B
20” (51.2 cm)
C
47⁄10” (12 cm)
D
2” (5.2 cm)
E
31⁄4” x 10” (8.3 x 25.4 cm)
F
7” (17.8 cm)
D
C
A
4
B
LIST OF MATERIALS
Removing the packaging.
I CAUTION
Remove carton carefully, Wear gloves to protect against sharp edges.
I WARNING
Remove the protective film covering the product before putting into operation.
Supplied Part
Pieces
Supplied Part
Pieces
1
1
Rectangular duct 3 ⁄4” x 10” (8.3 x 25.4 cm)
with back draft dampers
1
Hood assembly and
LED lamps already installed
4.5x13 mm
4
1
7” (17.8 cm) round transition
3.5x6.5 mm
1
Parts no supplied
Tools/Materials required
• Drill
• 11⁄4” (3.0 cm) drill bit
• 1⁄8” (3.0 mm) drill bit for pilot holes
• Pencil
• Wire stripper or utility knife
• Tape measure or ruler
• Caulking gun and weatherproof caulking compound
• Saber or keyhole saw
• Metal snips
• Screwdrivers:
- Phillips
- Flat-blade
Optional accessories and consumable parts
KIT
Recirculating Kit
7” Round Kit
Upgrade Filters
Kit
# Part
30” (76.2 cm)
36” (91.4 cm)
KIT02178
(EBLRCK02)
KIT02179
(EBLRCK03)
KIT02723 (EXXNRVRD)
KIT02591
(EBLGFK30)
KIT02592
(EBLGFK36)
5
Ducting Options
Closely follow the instructions set out in this manual.
All responsability, for any eventual inconveniences, damages or fires caused by not complying with the instructions in this
manual, is declined.
Ductless (Recirculating)
Horizontal Discharge
NOTE:
In cases where it should not be
possible to discharge cooking
fumes and vapour to the outside,
purchase:
The Ductless Recirculating Kit.
Use a rectangular duct
31⁄4” x 10” for discharge of
fumes to the outside.
Vertical Discharge
Use a rectangular duct 31⁄4” x 10” or use a
7” (17.8 cm) round transition for discharge of
fumes to the outside.
Preparation
Do not cut a joist or stud unless absolutely necessary. If a joist
or stud must be cut, then a supporting frame must be
constructed.
Fittings material is provided to secure the hood to most types
of walls/ceilings.
However, a qualified technician must verify suitability of the
materials in accordance with the type of wall/ceiling.
Before making cutouts, make sure there is proper clearance
within the ceiling or wall for exhaust vent.
Recommended installation height:
Hood installation height above cooktop is the users preference.
The lower the hood is above the cooktop, the more efficient
the capturing of cooking odors, grease and smoke.
6
I CAUTION
THAT THE BOTTOM EDGE IS AT 30” (76.2 CM) ABOVE THE
COOKING SURFACE.
FOR ELECTRIC RANGES INSTALLATION: MOUNT THIS HOOD
SO THAT THE BOTTOM IS NOT LESS THAN 24” (61 CM)
AND NOT MORE THAT 30” (76.2 CM) ABOVE THE COOKING
SURFACE.
HOUSEHOLD USE. PLEASE, READ INSTALLATION MANUAL
FOR SPECIFIC APPLICATION.
Check your ceiling height and the hood height maximum
before you select your hood.
Installation- Ducting Version
After having choosen the vent option, proceed as follows:
1
R1
Remove the grease filters.
Rectangular
vertical discharge
vertical
R2 Round
discharge
R1 Rectangular
horizontal discharge
4
2
Remove the junction box cover. Remove either the top or
the back wiring knockout according the preference and
install an approved wiring clamp.
J-Box cover
For rectangular ducted discharge installations only.
Attach exhaust adaptor/damper over knockout opening
with two exhaust adaptor screws. Make sure damper pivot is nearest to top/back edge of
hood. Remove tape from damper flap.
NOTE: The exhaust adaptor/damper can be installed up to 1 inch
on either side of the hood center to accommodate off-center
ductwork. In extreme offcenter installations,one end of the duct
connector may need to be trimmed to clear the electrical cable
clamp.
Pivot
Wiring clamp
Top/back edge
Exhaust transition/ damper
5
For round ducted discharge installations install 7” (17.8 cm)
transition with its screws (2).
NOTE: The round transition can be installed up to 1 inch on
either side of the hood center to accommodate off-center
ductwork. In extreme offcenter installations, one end of the
duct connector may need to be trimmed to clear the electrical
cable clamp.
3
Remove the duct knockouts using a flat blade screwdriver
and a small hammer. Use the screwdriver by knocking
out the pannel in similar fashion to a scalpel. Take care of
sharp edges.
7” round transition
IATTENTION
If it is intended to use the hood in the recirculating version do
not remove any duct knockouts and order the necessary
charcoal filter from your supplier.
R1 = Remove rectangular duct knockout only.
R2 = Remove semicircular and rectangular duct knockouts.
7
Mark holes
1 Select the vent option that your installation will require
and proceed to that section:
Outside top exhaust
(Vertical duct– 3 1⁄4”x 10” Rectangular)
Use the diagram or the hood as a template and mark the
locations on the cabinet for ductwork, electrical wiring and
keyhole screw slots.
Hood mounting screws (4)
13 15⁄16” (30” hood)
16 15⁄16” (36” Hood)
Cabinet front
13 15⁄16” (30” hood)
16 15⁄16” (36” Hood)
12 1⁄2”
Cabinet bottom
5 1⁄4”
5 1⁄4”
5”
Choose Venting Option 1 The hood can be set to vent outside or to recirculate air
back into the kitchen. The plastic vent lever is located near
the center of the hood opening. To vent to the outside, make sure the plastic vent lever is
in the HORIZONTAL position (flat against the metal top
of the hood). To recirculate air into the kitchen, make sure
the plastic vent lever is in the VERTICAL position
(flat against the plastic blower housing).
NOTE: In order to change the vent lever position, you will
need to pull the lever out slightly to clear the plastic tabs.
10 1⁄2”
1 1⁄4”
Vertical duct
access hole
Installation- Recirculating
Use the hood as a template and mark the locations on the
cabinet for the electrical wiring and keyhole screw slots.
Since the hood is to be recirculated (not to be vented outside),
do not cut out any vent openings in the wall or cabinet bottom.
Set for
outside venting
1 1⁄2”
1 1⁄4”
Wood shims (recessed Centerline
bottom cabinets only)
Set for
recirculating
Stop tab
Electrical access
hole (in cabinet
bottom)
Stop tab
Outside top exhaust (Only recirculating version)
(Vertical duct–7” Round)
Use the diagram or the hood as a template and mark the
locations on the cabinet for ductwork, electrical wiring and
keyhole screw slots.
Hood mounting screws (4)
13 15 16” (30” hood)
16 15 16” (36” Hood)
Cabinet front
13 15 16” (30” hood)
16 15 16” (36” Hood)
12 1 2”
Cabinet bottom
Access hole for
7” round duct
HOLE
8” DIA.
5”
Wood shims (recessed
bottom cabinets only)
1 1 4”
10 1 2”
1 1 2”
Electrical access hole
(in cabinet bottom)
Centerline
Hood shown lying upside down
For recessed bottom cabinet only 1 If the cabinets have front, side or back trim, make 2 wood
shims the width of the trim and attach them to the cabinet
bottom recess on both sides. See previous page for marking locations.
Outside rear exhaust
(Horizontal duct– 3 1⁄4”x 10” Rectangular)
Use the diagram or the hood as a template and mark the
locations on the cabinet for ductwork, electrical wiring and
keyhole screw slots.
Cabinet front
1
3 34”
Cabinet
bottom
8
” 1 9 16”
Horizontal duct
access hole
5 1 4 ”5
13 15 16” (30” hood)
16 15 16” (36” Hood)
Hood mounting
screws (4)
8
”
12 16”
13 15 16” (30” hood)
16 15 16” (36” Hood)
1
4
Wood shims
2
3
7
Centerline
Electrical access hole
(in wall)
4
5
Cut holes at marked locations for duct and electrical
wiring. For the vertical duct, cut out 3⁄4” extra toward the
front of the cabinet so you can move the duct freely when
installing the hood. It may also ease installation by cutting
the hole 101⁄ 2” instead of 10”.
Drive a mounting screw (from the hardware packet)
partway into each center of the narrow neck of the keyhole
slots marked on the cabinet bottom.
Fix the wiring conduit to the hood.
Slide the hood back against the wall. Tighten the mounting
screws. Be sure the screw heads are in the narrow neck of
the keyhole slot. Connect Ductwork to hood.
Electrical Connection
IWARNING
•
ELECTRICAL SHOCK HAZARD.
IWARNING
Run 3 wires; black, white and green ,according to the
National Electrical Code and local codes and ordinances,
in 1⁄2” conduit from service panel to junction box.
TURN OFF POWER CIRCUIT AT THE SERVICE PANEL
BEFORE WIRING THIS UNIT.
120 VAC, 15 OR 20 AMP CIRCUIT REQUIRED.
G
•
A
B
F
Remove the knockout and the Junction box cover and
install the conduit connector (cULus listed) in junction box.
A
A.
A.
B.
C.
D.
White wires
Black wires
UL listed wire connector
Green (or bare) ground wire
E.
Home power supply cable or
power cord accessory kit
F. UL listed or CSA approved ½”
strain relief
G. Green ground screw
•
Connect black wire from service panel to black or red in
junction box, white to white and green to green-yellow.
•
Close and secure junction box cover.
Terminal box cover
Complete Installation
Description of the Hood
Replace filters.
Check operation of the hood.
If range hood does not operate:
• Check that the circuit breaker is not tripped or the house
fuse blown.
•
E
D
C
ELECTRICAL GROUNDING INSTRUCTIONS
THIS APPLIANCE IS FITTED WITH AN ELECTRICAL JUNCTION
BOX WITH 3 WIRES, ONE OF WHICH (GREEN/YELLOW)
SERVES TO GROUND THE APPLIANCE. TO PROTECT YOU
AGAINST ELECTRIC SHOCK, THE GREEN AND YELLOW WIRE
MUST BE CONNECTED TO THE GROUNDING WIRE IN YOUR
HOME ELECTRICAL SYSTEM, AND IT MUST UNDER NO
CIRCUMSTANCES BE CUT OR REMOVED.
Failure to do so can result in death or electrical shock.
Disconnect power supply. Check that wiring is correct.
1
3
2
To get the most efficient use from your new range hood,
read the “Mainteinance” section.
Keep your Installation Instructions and Use and Care Guide
close to range hood for easy reference.
4
3
1.
2.
3.
4.
Blower and light controls
LED lamps
Grease filter handle
Grease filter
9
CFM
REDUCTION
SYSTEM
Control
1
2
3
4
5
Mainteinance
6
1. Button ON/OFF motor (stand by)
2. Button for low speed (suction power) selection
When flashing, it indicates that you must wash the grease filter.
3. Button for medium speed (suction power) selection
4. Button for high speed (suction power) selection
5. Button for intensive speed (suction power) selection Cleaning
Do not spray cleaners directly to the control while cleaning the
Hood. The cooker hood should be cleaned regularly (at least
with the same frequency with which you carry out maintenance
of the fat filters) internally and externally. Clean using the
cloth dampened with neutral liquid detergent. Do not use
abrasive products.
DO NOT USE ALCOHOL!
I WARNING:
Failure to carry out the basic cleaning recommendations of the
cooker hood and replacement of the filters may cause fire risks.
Therefore, we recommend oserving these instructions.
The manufacturer declines all responsibility for any damage to
the motor or any fire damage linked to inappropriate maintenance
or failure to observe the above safety recommendations.
It lasts 5 minutes then it returns to medium speed (suction power).
6. Button ON/OFF lighting
Press briefly to switch on or off the lighting of the hood.
Press and hold to adjust the intensity of the light.
Grease Filter
Traps cooking grease particles.
This must be cleaned once a month using non aggressive
detergents, either by hand or in the dishwasher, which must be
set to a low temperature and a short cycle. When washed in
a dishwasher, the grease filter may discolour slightly, but this
does not affect its filtering capacity.
To remove the grease filter, pull the spring release handle.
Indicators of filter saturation:
At regular time intervals, the hood indicates the need of
performing filter maintenance.
Button
on with steady light:
Perform grease filter maintenance.
Button
flashing:
Perform activated charcoal filter maintenance.
Note: Filter saturation signal is visible within the first minute
after switching off the hood; within this time, the reset of
saturation indicators must be performed.
A
Reset of filter saturation indicators:
Press and hold the button
Activation of saturation indicator activated charcoal filter:
Note: This operation must be performed with the hood off.
This indicator is normally desactivated; press and hold the
button
to activate the function: the button lights up with
steady light.
To desactivate the function, press and hold the button
the button lights up flashing.
,
Before operating your hood:
Some regions and provinces of the US and Canada restrict
the exhausting power of range hoods to performances below
certain values. These values are underlined in the local code
for your area.
Please check your local code to find out if you will need to
restrict the power of your hood.
If your local code restricts the performance values of range
hoods, please execute the following button-pressing sequence:
Low performance:
This function allows to lock the user interface to control the
third and four speeds.
This function can be enabled only with motor OFF.
1
5
•
Press the ON/OFF (1) and Intensive speed (5) buttons
together for 3 seconds.
•
You will hear a beep and all control lights will go on for 3
seconds.
The 3rd and 4th speeds will be Disabled.
10
Replacing a LED Lamp
The LED lights are replaceable by a service technician only.
See “Assistance and Service” section for service contact
information.
Charcoal Filter
If the model is not vented to the outside, the air will be
recirculated through disposable charcoal filters that help
remove smoke and odors.
The charcoal filters cannot be cleaned.
They must be replaced.
The charcoal filters are clipped inside of each metal grease
filter (mounting instructions included with charcoal filters kit).
The charcoal filters should be replaced every 4-6 months
(depending on hood usage).
NOTE: DO NOT rinse, or put charcoal filters in an automatic
dishwasher.
NOTE: Charcoal filters are not included with the hood.
They must be ordered from your supplier.
Order the needed kit specifying your hood model and width
size.
Charcoal filter placement (Recirculating accessories)
Fit the charcoal filter mattress on the upper side of each
grease filter.
Use provided springs to fix it in place.
NOTE: When removing for replacing for a new one do not
remove Fixing Springs, simply pull out one and rotate outwards.
Fixing spring
Charcoal filter
Grease filter
top side
11
ELICA North America
TWO-YEARS LIMITED WARRANTY
TO OBTAIN SERVICE UNDER WARRANTY
Owner must present proof of original purchase date. Please keep a copy of your dated proof of purchase (sales slip) in
order to obtain service under warranty.
PARTS AND SERVICE WARRANTY
For the period of two (2) years from the date of the original purchase, Elica will provide free of charge, non consumable
parts or components that failed due to manufacturing defects. During these two (2) years limited warranty, Elica will
also provide free of charge, all labor and in-home service to replace any defective parts.
WHAT IS NOT COVERED
•
Damage or failure to the product caused by accident or act of God, such as, flood, fire or earthquake.
•
Damage or failure caused by modification of the product or use of non-genuine parts.
•
Damage or failure to the product caused during delivery, handling or installation.
•
Damage or failure to the product caused by operator abuse.
•
Damage or failure to the product caused by dwelling fuse replacement or resetting of circuit breakers.
•
Damage or failure caused by use of product in a commercial application.
•
Service trips to dwelling to provide use or installation guidance.
•
Light bulbs, metal or carbon filters and any other consumable part.
•
Normal wear of finish.
•
Wear to finish due to operator abuse, improper maintenance, use of corrosive or abrasive cleaning products/pads and
oven cleaner products.
WHO IS COVERED
This warranty is extended to the original purchaser for products purchased for ordinary residential use in North America
(Including the United States, Guam, Puerto Rico, US Virgin Islands & Canada).
This warranty is non-transferable and applies only to the original purchaser and does not extend to subsequent owners of
the product. This warranty is made expressly in lieu of all other warranties, expressed or implied, including, but not limited
to any implied warranty of merchantability or fitness for a particular purpose and all other obligations on the part of Elica
North America, provided, however, that if the disclaimer of implied warranties is ineffective under applicable law, the duration of any implied warranty arising by operation of law shall be limited to two (2) years from the date of original purchase
at retail or such longer period as may be required by applicable law.
This warranty does not cover any special, incidental and/or consequential damages, nor loss of profits, suffered by the
original purchaser, its customers and/or the users of the Products.
WHO TO CONTACT
To obtain service under warranty or for any service related question:
• Elica North America Authorized Service - 888 732 8018
• elica@servicepower.com
12
13
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising