Kobe | RA0248SQB-1 | Manual-PDF | Kobe RA0248SQB-1 Manual-PDF

Kobe RA0248SQB-1 Manual-PDF
KOBE Brand Range Hood
CH-100 Series (18” Height)
Model No.:
CH0030SQB-1 (30”)
CH0036SQB-1 (36”)
CH0042SQB-1 (42”)
CH0048SQB-1 (48”)
RA-02 Series (18” Height)
Model No.:
RA0230SQB-1 (30”)
RA0236SQB-1 (36”)
RA0242SQB-1 (42”)
RA0248SQB-1 (48”)
INSTALLATION INSTRUCTIONS
AND OPERATION MANUAL
- READ AND SAVE THESE INSTRUCTIONS -
CONTENTS
IMPORTANT SAFETY INSTRUCTIONS .................................................................................... 1
COMPONENTS OF PACKAGE.................................................................................................. 3
INSTALLATION .......................................................................................................................... 5
OPERATION INSTRUCTIONS..................................................................................................15
MAINTENANCE ........................................................................................................................16
SPECIFICATIONS ....................................................................................................................17
MEASUREMENTS & DIAGRAMS.............................................................................................19
PARTS LIST..............................................................................................................................22
CIRCUIT DIAGRAM ..................................................................................................................28
TROUBLE SHOOTING .............................................................................................................29
DISCLAIMER ............................................................................................................................30
WARRANTY .............................................................................................................................31
PRODUCT REGISTRATION .....................................................................................................33
- READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING ALL WIRING MUST BE DONE BY A PROFESSIONAL AND IN ACCORDANCE WITH
NATIONAL AND LOCAL ELECTRICAL CODES.
IMPORTANT SAFETY INSTRUCTIONS
- PLEASE READ THIS SECTION CAREFULLY BEFORE INSTALLATION -
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL
INJURY, OBSERVE THE FOLLOWING:
1) Installation and electrical wiring must be done by qualified professionals and in accordance with all
applicable codes and standards, including fire-rated construction.
2) When cutting or drilling into wall or ceiling, be careful not to damage electrical wiring or other hidden
utilities.
3) Ducted fans must be vented to the outside.
a) Before servicing or cleaning unit, open the light panel and SWITCH POWER OFF AT SERVICE
PANEL.
b) Clean all grease laden surfaces frequently. To reduce the risk of fire and to disperse air
properly, make sure to vent air outside. DO NOT vent exhaust air into wall spaces, attics, crawl
spaces or garages.
NOTE
-
This warranty is invalid without an authorized agent’s receipt or if unit is
damaged due to misuse, poor installation, improper use, mistreatment,
negligence or any other circumstances beyond the control of KOBE
RANGE HOODS authorized agents. Any repair carried out without the
supervision of KOBE RANGE HOODS authorized agents will
automatically void the warranty.
-
KOBE RANGE HOODS will not be held responsible for any damages to
personal property or real estate or any bodily injuries whether caused
directly or indirectly by the range hood.
WARNING:
TO REDUCE THE RISK OF PERSONAL INJURY IN THE EVENT OF A RANGE
TOP GREASE FIRE:
1. Keep all fan, baffle/spacer/filter/oil tunnel/oil container and grease-laden surfaces clean. Grease
should not be allowed to accumulate on fan, baffle/spacer/filter/oil tunnel/oil container.
2. Always turn hood ON when cooking.
3. Use high settings on cooking range ONLY when necessary.
4. Do not leave cooking range unattended when cooking.
5. Always use cookware and utensils appropriate for the type and amount of food prepared.
6. Use this unit only in the manner intended by the manufacturer.
7. Before servicing, switch power off at service panel and lock service panel (if possible) to prevent
power from switching on accidentally.
8. Clean ventilating fan frequently.
1
What to Do In The Event Of a Range Top Grease Fire
•
•
•
•
SMOTHER FLAMES with a tight fitting lid, cookie sheet, or metal tray, and then turn off the burner.
KEEP FLAMMABLE OR COMBUSTIBLE MATERIAL AWAY FROM FLAMES. If the flames do not
go out immediately, EVACUATE THE AREA AND CALL THE FIRE DEPARTMENT or 911.
NEVER PICK UP A BURNING PAN – You May Get Burned.
DO NOT USE WATER, including wet dishcloths or towels – a violent steam blast will result.
Use an extinguisher ONLY if:
a) You have a Class A, B, C extinguisher and know how to operate it.
b) The fire is small and contained in the area where it started.
c) The fire department has been called.
d) You can fight the fire with your back to an exit.
What to Do If You Smell Gas
-
Extinguish any open flame.
Do not try to turn on the lights or any type of appliance.
Open all doors and windows to disperse the gas. If you still smell gas, call the Gas Company and
Fire Department right away.
CAUTION
1) For general ventilation use only. Do not use to exhaust hazardous or explosive materials and
vapors.
2) To reduce the risk of fire, use only metal ductwork. Sufficient air is needed for proper combustion
and exhausting of gases through the flue (chimney) to prevent back drafting.
3) Follow the heating equipment manufacturer’s guideline and safety standards such as those
published by the National Fire Protection Association (NFPA), and the American Society for
Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and code authorities.
4) Activating any switch on may cause ignition or an explosion.
5) Due to the size and weight of this hood, two people installation is recommended.
ELECTRICAL SHOCK HAZARD – Can result in serious injury or death.
Disconnect appliance from electric power before servicing. If equipped,
the fluorescent light bulb contains small amounts of mercury, which
must be recycled or disposed of according to Local, State, and Federal
Codes.
2
COMPONENTS OF PACKAGE
(Must keep all material for returns or refunds)
CH-100 Series
RANGE HOOD BOX
{A} KOBE Range Hood – 1
{B} Warranty Registration Card –1
{C} Instructions Manual – 1
{D} Oil Tunnel – 1
{E} Baffle Filter
- 2 (30” & 36”)
- 3 (42” & 48”)
{F} Spacer – 2
{G} 8” Round Exhaust Plate – 1
{H}
(42” & 48” only)
{H}
{I}
{J}
Screws Package – 1
Hood-Mounting Bracket – 2
Screws Package – 1
{I}
{J}
{A}
Duct Cover
(Sold Separately)
Option Of:
Model No. CH0030DC-12 for 30'' hood
KOBE Duct Cover – 1
Screw Package for Duct Cover – 1
{B}
{C}
Model No. CH0036DC-12 for 36'' hood
KOBE Duct Cover – 1
Screw Package for Duct Cover – 1
Model No. CH0042DC-12 for 42'' hood
KOBE Duct Cover – 1
Screw Package for Duct Cover – 1
{D}
{E}
{F}
{G}
Model No. CH0048DC-12 for 48'' hood
KOBE Duct Cover – 1
Screw Package for Duct Cover – 1
3
RA-02 Series
RANGE HOOD BOX
(BOX 1 OF 2)
{A} KOBE Range Hood – 1
{B} Warranty Registration Card –1
{C} Instructions Manual – 1
{D} Oil Tunnel – 1
{E} Baffle Filter
2 (30” & 36”)
3 (42” & 48”)
{F} Spacer – 2
{G} 8” Round Exhaust Plate – 1
{F}
{G}
{H}
(42” & 48” only)
{H} Screws Package – 1
{I} Hood-Mounting Bracket – 1
{J} Screws Package – 1
{A}
{I}
{B}
{J}
{C}
BOX 2 OF 2
ITEM NO.: RA02DC
{K}
{D}
Duct Cover
{E}
{K}
-
FOR MORE INFORMATION, PLEASE VISIT OUR W EBSITE www.KOBERangeHoods.com OR
CONTACT KOBE RANGE HOODS AT (626) 775-8880.
4
INSTALLATION
PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING
Calculation before Installation
Calculate the length of the installation, before installing the hood. (All calculation is measure in inches.)
- FOR UNDER THE CABINET TABLE 1
CH-100 Series
A = Height of Floor to Ceiling
B = Height of Floor to Counter Top
(Standard: 36”)
C = Preferred Height of Counter Top to Hood
Bottom (Recommended 30” to 36”)
D = Height of Hood
E = Height of the Cabinet
- FOR STAND ALONE TABLE 2
CH-100 Series
A = Height of Floor to Ceiling
B = Height of Floor to Counter Top
(Standard: 36”)
C = Preferred Height of Counter Top to Hood
Bottom (Recommended 30” to 36”)
[(A – B] – (D + E)]
D = Height of Hood
E = Height of Duct Cover
5
RA-02 Series
SAFETY WARNING
HOOD MAY HAVE VERY SHARP EDGES; PLEASE WEAR PROTECTIVE GLOVES IF IT IS
NECESSARY TO REMOVE ANY PARTS FOR INSTALLING, CLEANING OR SERVICING.
NOTE: BE CAREFUL WHEN USING ELECTRICAL SCREWDRIVER, DAMAGE TO THE HOOD
MAY OCCUR.
CH-100 SERIES – UNDER THE CABINET INSTALLATION ................................................................. 7
CH-100 SERIES – STAND ALONE INSTALLATION ............................................................................. 9
RA-02 SERIES - INSTALLATION ........................................................................................................ 12
6
CH-100 SERIES – UNDER THE CABINET INSTALLATION
Figure 1
Preparation before Installation
NOTE:
TO AVOID DAMAGE TO YOUR HOOD,
PREVENT DEBRIS FROM ENTERING
THE VENT OPENING.
Decide the location of the venting pipe from the
hood to the outside. Refer to Figure 1.
A straight, short venting run will allow the hood
to perform more efficiently.
Try to avoid as many transitions, elbows, and
long run as possible. This may reduce the
performance of the hood.
Temporarily wire the hood to test for proper
operation before installing.
Important: Peel protective film off the hood
(if any).
For installing under the cabinet with recessed
bottom, attach 4-inch wide wood filler strips (not
included) on each side. Refer to Figure 2.
Measure and create access opening for
electrical wires under the cabinet.
Figure 2
Hood Installation
CAUTION: If required to move the cooking
range to install the hood, turn off the power on
an electric range at the main electrical box.
SHUT OFF THE GAS BEFORE MOVING A GAS
RANGE.
Figure 3
1. Puncture the knockout holes on the hood as
shown in Figure 3.
2. (This step only applies to 42” and 48”
models.) Attach exhaust plate on hood with
four (3/16” x 3/8”) screws (included). Shown
in Figure 4.
3. Using
references
on
Table
1
and
measurements on page 19 center the hood in
place beneath the cabinet and flush with the
front of the cabinet.
4. Draw electrical wires through cabinet access
opening. Refer to Figure 6.
5. From the bottom of the hood, place screw (not
provided) into the exact center of each
knockout hole. Make sure all screws are in
place before tightening screws. CAUTION:
MAKE SURE THE HOOD IS SECURE
BEFORE RELEASING.
6. For safety purpose, pre-drilled mounting holes
are provided through the back of the hood. For
a more secure installation, use as many
mounting holes as needed to secure from the
inside of hood (screws not included).
Figure 4
7
Figure 5
Ductwork Installation
7. Use 6” round steel pipe for 30” and 36”
models or 8” round steel pipe for 42” and 48”
models (follow building codes in your area) to
connect the exhaust on the hood to the
ductwork above. Use duct tape to make all
joints secure and air tight. Refer to Figure 5.
Wiring to Power Supply
SAFETY WARNING
Figure 6
RISK OF ELECTRICAL SHOCK. THIS RANGE
HOOD MUST BE PROPERLY GROUNDED.
MAKE SURE THIS IS DONE BY SPECIALIZED
ELECTRICIAN IN ACCORDANCE WITH ALL
APPLICABLE
NATIONAL
AND
LOCAL
ELECTRICAL CODES. BEFORE CONNECTING
WIRES, SWITCH POWER OFF AT SERVICE
PANEL AND LOCK SERVICE PANEL TO
PREVENT POWER FROM BEING SWITCHED
ON ACCIDENTALLY.
8. Connect the electrical wires.
- Connect three wires (black, white and
green) to house wires and cap with wire
connectors. Connect according to color:
black to black, white to white, and green to
green as shown on Figure 6.
- If necessary to hide the electrical wire
connections, push wires back into the
wiring box. Access the wire connections
underneath the hood. To prevent any
damage, make sure wires do not slip
between motor or any moving parts.
Figure 7
Install Accessories
Figure 8
9. Attach Oil Tunnel. Refer to Figure 7.
10. Refer to Figure 8. Slide the baffle filter into
the hood. Push the baffle filter upward. Slide forward. Pull downward. Fit into
place.
11. Repeat until all baffle filters and spacers are
resting against oil tunnel. Refer to page 20.
12. Install heat lamps (not included), 120 Volts 175
Watts max. each.
Final Assembly
13. Turn power ON in control panel. Check all
lights and fan operation.
14. Make sure to leave this manual for the
homeowner.
8
CH-100 SERIES – STAND ALONE INSTALLATION
***This installation only applies with the purchase
of an optional duct cover:
Figure 9
Preparation before Installation
NOTE:
TO AVOID DAMAGE TO YOUR HOOD,
PREVENT DEBRIS FROM ENTERING
THE VENT OPENING.
Decide the location of the venting pipe from the
hood to the outside. Refer to Figure 9.
A straight, short venting run will allow the hood
to perform more efficiently.
Try to avoid as many transitions, elbows, and
long run as possible. This may reduce the
performance of the hood.
Temporarily wire the hood to test for proper
operation before installing.
Important: Peel protective film off the hood
and the duct cover (if any).
If necessary, prepare back wall frame with
cross framing lumber for secure installation.
Using
references
on
Table
2
and
measurements on page 19-20, decide the level
of the lumber. Refer to Figure 10.
Figure 10
Hood Installation
Figure 11
CAUTION: If required to move the cooking
range to install the hood, turn off the power on
an electric range at the main electrical box.
SHUT OFF THE GAS BEFORE MOVING A GAS
RANGE.
1. (This step only applies to 42” and 48” models.)
Attach exhaust plate on hood with four (3/16” x
3/8”) screws (included). Shown in Figure 11.
2. If necessary, remove the rubber stand on the
back of the hood and discard.
3. Use twelve (3/16” x 3/8”) screws (included) to
attach the two hood-mounting brackets
(included) to the back of the hood. Refer to
Figure 12.
4. Using references in Table 2 on page 5 and
Measurements and Diagrams on pages 19-20,
mark the leveling point of the hood. Position
two mounting screws (not included) on the wall,
leaving 1/8” away from the wall. Refer to Figure
13.
Figure 12
9
5. Align hood-mounting bracket to the two screws
on the wall and hook hood into place. Tighten
screws to secure hood to the wall.
6. For safety purpose, pre-drilled mounting holes
are provided through the back of the hood. For
a more secure installation, use as many
mounting holes as needed to secure from the
inside of hood (screws not included).
CAUTION: MAKE SURE HOOD
SECURE BEFORE RELEASING.
Figure 13
WALL
IS
Wiring to Power Supply
Figure 14
SAFETY WARNING
RISK OF ELECTRICAL SHOCK. THIS RANGE
HOOD MUST BE PROPERLY GROUNDED.
MAKE SURE THIS IS DONE BY SPECIALIZED
ELECTRICIAN IN ACCORDANCE WITH ALL
APPLICABLE
NATIONAL
AND
LOCAL
ELECTRICAL CODES. BEFORE CONNECTING
WIRES, SWITCH POWER OFF AT SERVICE
PANEL AND LOCK SERVICE PANEL TO
PREVENT
POWER FROM BEING SWITCHED ON
ACCIDENTALLY.
7. Connect the electrical wires.
- Connect three wires (black, white and
green) to house wires and cap with wire
connectors. Connect according to color:
black to black, white to white, and green to
green as shown on Figure 14.
- If necessary to hide the electrical wire
connections, push wires back into the
wiring box. Access the wire connections
underneath the hood. To prevent any
damage, make sure wires do not slip
between motor or any moving parts.
10
Figure 15
Duct Cover Installation
8. Use 6” round steel pipe for 30” and 36” models
or 8” round steel pipe for 42” and 48” models
(follow building codes in your area) to connect
the exhaust on the hood to the ductwork
above. Use duct tape to make all joints secure
and air tight. Refer Figure 15. Slide the duct
cover onto the hood.
9. Use 3/16” x 3/8” screws (included) to attach
duct cover to hood.
Figure 16
Install Accessories
10. Attach oil tunnel. Refer to Figure 16.
11. Refer to Figure 17. Slide the baffle filter into
the hood. Push the baffle filter upward. Slide forward. Pull downward. Fit into
place.
12. Repeat until all baffle filters and spacers are
resting against oil tunnel. Refer to page 20.
13. Install heat lamps (not included), 120 Volts 175
Watts max. each.
Final Assembly
Figure 17
14. Turn power ON in control panel. Check all
lights and fan operation.
15. Make sure to leave this manual for the
homeowner.
11
RA-02 SERIES - INSTALLATION
Figure 19
Preparation before Installation
NOTE:
TO AVOID DAMAGE TO YOUR HOOD,
PREVENT DEBRIS FROM ENTERING
THE VENT OPENING.
Decide the location of the venting pipe from the
hood to the outside. (Figure 18)
A straight, short venting run will allow the hood
to perform more efficiently.
Try to avoid as many transitions, elbows, and
long run as possible. This may reduce the
performance of the hood.
Temporarily wire the hood to test for proper
operation before installing
Important: Peel protective film off the hood
and the duct cover (if any).
If necessary, prepare back wall frame with cross
framing lumber for secure installation. Refer to
Table 2 and measurements on Page 21 to
decide the level of the lumber. (Figure 19)
Loosen hood-mounting brackets at the back of
the hood, adjust brackets and tighten screws as
shown in Figure 20.
If necessary, remove the rubber stand on the
back of the hood and discard. (Figure 21)
Figure 18
Figure 20
Figure 21
12
Figure 22
Hood Installation
CAUTION: If required to move the cooking
range to install the hood, turn off the
power on an electric range at the main
electrical box.
SHUT OFF THE GAS
BEFORE MOVING A GAS RANGE.
1. Using references in Table 2 and measurements
on Page 21, mark the leveling locations point for
hood-mounting bracket on the wall.
2. Secure two mounting screws (not provided) to
the wall, leaving an 1/8” space from the wall.
(Figure 22)
3. Align the hood-mounting bracket to the
mounting screws on the wall and hang hood into
place.
4. Secure and tighten the mounting screws.
Figure 23
CAUTION: MAKE SURE HOOD IS SECURE
BEFORE RELEASING.
Wiring to Power Supply
SAFETY WARNING
RISK OF ELECTRICAL SHOCK. THIS RANGE
HOOD MUST BE PROPERLY GROUNDED.
MAKE SURE THIS IS DONE BY SPECIALIZED
ELECTRICIAN IN ACCORDANCE WITH ALL
APPLICABLE
NATIONAL
AND
LOCAL
ELECTRICAL CODES. BEFORE CONNECTING
WIRES, SWITCH POWER OFF AT SERVICE
PANEL AND LOCK SERVICE PANEL TO
PREVENT POWER FROM BEING SWITCHED ON
ACCIDENTALLY.
5. Connect the electrical wires.
- Connect three wires (black, white and
green) to house wires and cap with wire
connectors. Connect according to color:
black to black, white to white, and green to
green as shown on Figure 23.
- If necessary to hide the electrical wire
connections, push wires back into the wiring
box.
Access the wire connections
underneath the hood. To prevent any
damage, make sure wires do not slip
between motor or any moving parts.
13
Figure 24
Figure 25
Figure 26
Duct Cover Installation
6. Use 6” round steel pipe for 30” and 36” models
or 8” round steel pipe for 42” and 48” models
(follow building codes in your area) to connect
the exhaust on the hood to the ductwork above.
Use duct tape to make all joints secure and air
tight. Refer Figure 24.
7. Use four 4mm x 8mm screws (included) to attach
duct cover to hood. Refer to Figure 25.
Install Accessories
8. Attach oil tunnel. Refer to Figure 26.
9. Refer to Figure 27. Slide the baffle filter into
the hood. Push the baffle filter upward. Slide forward. Pull downward. Fit into
place.
10. Repeat until all baffle filters and spacers are
resting against oil tunnel. Refer to page 21.
Final Assembly
11. Turn power ON in control panel. Check all lights
and fan operation.
12. Make sure to leave this manual for the
homeowner.
14
Figure 27
OPERATION INSTRUCTIONS
This KOBE hood is equipped with two rotary controls with powerful centrifugal squirrel cage, baffle
filters, and bright LED lights.
The two rotary controls are Light Control & Speed Control. Refer to Figure 28.
Figure 28
Note: For best results, turn hood to QuietMode™ prior to preparation or cooking to establish
airflow in the kitchen. Adjust speed as needed.
•
Rotate the Speed Control clockwise to cycle from QuietMode™, Low, High, and Off;
and rotate counterclockwise to cycle from High, Low, QuietMode™, and off
•
Rotate the Light Control clockwise to turn on the light.
For CH-100 Series only
•
Press the back Red button to turn on heat lamps.
(Note: Heat lamps are sold separately. Heat lamps required 120-volt,
175-watt.)
15
MAINTENANCE
For the optimal level of operation, clean the range hood surface and baffles regularly.
To Clean Hood Surface
CAUTION: NEVER USE ABRASIVE CLEANERS, PADS, OR CLOTHS.
*** Regular care will help preserve its fine appearance.
1. Use only mild soap or detergent solutions. Dry surfaces using soft cloth.
2. If hood looks splotchy (stainless steel hood), use an orange base cleaner to clean the surface of
the hood. Avoid cleaner to get on the control switches. Only spread a light coating over the
surface of the hood and leave on for a few minutes (do not leave on too long or this may cause
damage to hood finish). Use soft towel to wipe off the cleaning solution, gently rubs any
stubborn spots. Use a slightly damp towel to get rid of any cleaning solution. Use dry soft towel
to dry the hood.
3. To bring the glow back into a stainless steel finish, use a stainless steel cleaner.
4. DO NOT allow deposits to remain for long periods of time.
5. DO NOT use ordinary steel wool or steel brushes. Small bits of steel may adhere to the surface
causing rust.
6. DO NOT allow salt solutions, disinfectants, bleaches, or cleaning compounds to remain in
contact with stainless steel for extended periods. Many of these compounds contain chemicals,
which may be harmful. Rinse with water after exposure and wipe dry with a clean cloth.
To Clean Baffle Filters & Oil Tunnel
CAUTION: DRAIN BAFFLE FILTERS AND OIL TUNNEL BEFORE OIL WILL OVERFLOW.
1. Remove the baffle filters and oil tunnel..
2. Using a sponge, wash with warm soapy water. Dry completely before returning into place.
(Note: Baffle Filters are top rack dishwasher safe.)
16
SPECIFICATIONS
CH-100 Series
MODEL / SIZE
CH0030SQB-1 / 30” / Single Blower
CH0036SQB-1 / 36" / Single Blower
CH0042SQB-1 / 42” / Dual Blowers
CH0048SQB-1 / 48” / Dual Blowers
COLOR
Commercial Grade Stainless Steel
CONSUMPTION / AMPERE
CH0030SQB-1 – 700W
CH0036SQB-1 – 700W
CH0042SQB-1 – 700W
CH0048SQB-1 – 700W
VOLTAGE
120V 60Hz
NUMBER OF BLOWER
1 – 30”, 36”
2 – 42”, 48”
DESIGN
18-Gauge Seamless / Satin Finish
FAN TYPE: CENTRIFUGAL
Squirrel Cage
EXHAUST
Top 6” Round – 30”, 36”
Top 8” Round – 42”, 48”
CONTROLS
Rotary Switch
LIGHTS
3-Watt LED x 2 – 30”, 36”
3-Watt LED x 3 – 42”, 48”
HOOD DIMENSION
(W x D x H)
(CH0030SQB-1)
(CH0036SQB-1)
(CH0042SQB-1)
(CH0048SQB-1)
OPTIONAL ACCESSORIES
(W x D x H)
1) Duct Cover:
Model No. CH0030DC-12 (30” x 12” x 12”)
Model No. CH0036DC-12 (36” x 12” x 12”)
Model No. CH0042DC-12 (42” x 12” x 12”)
Model No. CH0048DC-12 (48” x 12” x 12”)
2) Model No. SSP30
30” Stainless Steel Back Panel (30” x 1/10” x 32”)
3) Model No. SSP36
36” Stainless Steel Back Panel (36” x 1/10” x 32”)
29-3/4” x 24” x 18”
35-3/4” x 24” x 18”
41-3/4” x 24” x 18”
47-3/4” x 24” x 18”
(CH0030SQB-1)
(CH0036SQB-1)
(CH0042SQB-1)
(CH0048SQB-1)
Net
60.0
67.0
86.0
93.0
Gross
78.0
87.0
108.0
117.0
QuietMode™
Low
High
Air Capacity (cfm)
Sone*
300
1.8
580
4.7
760
5.4
Air Capacity (cfm)
Sone*
450
2.5
800
6.0
1100
8.0
HOOD WEIGHT (lbs)
SPEED
SINGLE BLOWER
CH0030SQB-1
CH0036SQB-1
DUAL BLOWERS
CH0042SQB-1
CH0048SQB-1
/ 6A
/ 6A
/ 6A
/ 6A
*One sone is equivalent to the sound of a refrigerator at 40 decibels.
**Specifications subject to change without notice.
17
RA-02 Series
MODEL / SIZE
RA0230SQB-1 / 30” / Single Blower
RA0236SQB-1 / 36" / Single Blower
RA0242SQB-1 / 42” / Dual Blowers
RA0248SQB-1 / 48” / Dual Blowers
COLOR
Commercial Grade Stainless Steel
CONSUMPTION / AMPERE
RA0230SQB-1 – 350W
RA0236SQB-1 – 350W
RA0242SQB-1 – 350W
RA0248SQB-1 – 350W
VOLTAGE
120V 60Hz
NUMBER OF BLOWER
1 – 30”, 36”
2 – 42”, 48”
DESIGN
18-Gauge Seamless / Satin Finish
FAN TYPE: CENTRIFUGAL
Squirrel Cage
EXHAUST
Top 6” Round – 30”, 36”
Top 8” Round – 42”, 48”
CONTROLS
Rotary Switch
LIGHTS
3-Watt LED x 2 – 30”, 36”
3-Watt LED x 3 – 42”, 48”
HOOD DIMENSION
(W x D x H)
(RA0230SQB-1)
(RA0236SQB-1)
(RA0242SQB-1)
(RA0248SQB-1)
OPTIONAL ACCESSORIES
(W x D x H)
1) Model No. RA02DC-24
1-Piece Extension Duct Cover (15” x 12” x 24-1/2”)
2) Model No. SSP30
30” Stainless Steel Back Panel (30” x 1/10” x 32”)
3) Model No. SSP36
36” Stainless Steel Back Panel (36” x 1/10” x 32”)
29-3/4” x 24” x 18”
35-3/4” x 24” x 18”
41-3/4” x 24” x 18”
47-3/4” x 24” x 18”
Net
Gross
(RA0230SQB-1)
(RA0236SQB-1)
(RA0242SQB-1)
(RA0248SQB-1)
RA02DC
46
53
65
72
66
73
87
94
5
7
QuietMode™
Low
High
Air Capacity (cfm)
Sone*
300
1.8
580
4.7
760
5.4
Air Capacity (cfm)
Sone*
450
2.5
800
6.0
1100
8.0
HOOD WEIGHT (lbs)
SPEED
SINGLE BLOWER
RA0230SQB-1
RA0236SQB-1
DUAL BLOWERS
RA0242SQB-1
RA0248SQB-1
/ 3A
/ 3A
/ 3A
/ 3A
*One sone is equivalent to the sound of a refrigerator at 40 decibels.
**Specifications subject to change without notice.
18
MEASUREMENTS & DIAGRAMS
All measurements in ( ) are millimeters.
All inch measurements are converted from millimeters. Inch measurements are
estimated.
CH-100 Series
MODEL NO.: CH0030SQB-1 (30”)
CH0036SQB-1 (36”)
CH0042SQB-1 (42”)
CH0048SQB-1 (48”)
- FOR UNDER THE CABINET -
- FOR STAND ALONE -
19
- FOR STAND ALONE (WITH OPTIONAL DUCT COVER) CH-100 Series
MODEL NO.: CH0030SQB-1 (30”)
CH0036SQB-1 (36”)
CH0042SQB-1 (42”)
CH0048SQB-1 (48”)
***Hood-Mounting Bracket
***Rear Knockout Holes
20
All measurements in ( ) are millimeters.
All inch measurements are converted from millimeters. Inch measurements are
estimated.
RA-02 Series
MODEL NO.: RA0230SQB-1 (30”)
RA0236SQB-1 (36”)
RA0242SQB-1 (42”)
RA0248SQB-1 (48”)
21
PARTS LIST
CH-100 Series
MODEL NO.: CH0030SQB-1 (30”)
CH0036SQB-1 (36”)
CH0042SQB-1 (42”)
CH0048SQB-1 (48”)
NO.
1
2
3
DESCRIPTION
Screw (3/16” x 3/8” )
Hood Mounting Bracket
6” Round Plastic Exhaust
8” Round Exhaust Plate
4
Hood Casing
5
6
Heat Lamp Socket Cover
Heat Lamp Socket
7
Motor Mounting Bracket
8
Air Chamber & Motor
9
Safety Screen
10
LED Light
11
Capacitor Panel
12
Light Transformer
13
Capacitor
14
15
16
A
B
C
D
17
Valve Stem
Knob
Spacer
2” wide
5” wide
1-1/2” wide
4-1/2” wide
Baffle Filter
18
Oil Tunnel
MODEL /SIZE
CH0030SQB-1 / CH0036SQB-1
CH0042SQB-1 / CH0048SQB-1
CH0030SQB-1
CH0036SQB-1
CH0042SQB-1
CH0048SQB-1
CH0030SQB-1 / CH0036SQB-1
CH0042SQB-1 / CH0048SQB-1
CH0030SQB-1 / CH0036SQB-1
CH0042SQB-1 / CH0048SQB-1
CH0030SQB-1 / CH0036SQB-1
CH0042SQB-1 / CH0048SQB-1
CH0030SQB-1
CH0036SQB-1
CH0042SQB-1
CH0048SQB-1
CH0030SQB-1 / CH0036SQB-1
CH0042SQB-1 / CH0048SQB-1
CH0030SQB-1
CH0036SQB-1
CH0042SQB-1
CH0048SQB-1
CH0030SQB-1
CH0036SQB-1
CH0042SQB-1
CH0048SQB-1
PART NO.
C1-0707-0001
C1-0221-0330
C1-0505-0001
C1-0606-0101
B101-2130-02
B101-2136-02
B101-2142-02
B101-2148-02
C1-0204-2130
C1-0414-0120
C1-0105-2100-L
C1-0105-2142-L
C1-0302-A110-06
C1-0302-A120-01
C1-0302-A110-06-C
C1-0302-A120-01-C
C1-0403-0306
C1-0201-2130
C1-0201-2136
C1-0201-2142
C1-0201-2148
C1-0402-D001
C1-0401-A250-22
C1-0401-A300-08
C1-0405-0404-B
C1-0405-0400-A
B101-2130-09
B101-2136-09
B101-2142-09
B101-2148-09
B101-2130-15
B101-2130-14
B101-2136-14
B101-2142-14
B101-2148-14
(Optional Duct Cover)
ORIGINAL KIT
NO.
DESCRIPTION
01
Duct Cover
02
Screw (3/16” x 3/8”)
MODEL /SIZE
CH0030DC-12
CH0036DC-12
CH0042DC-12
CH0048DC-12
22
PART NO.
B102-6012-030
B102-6012-036
B102-6012-042
B102-6012-048
C1-0707-0001
CH-100 Series
MODEL NO.: CH0030SQB-1 (30”)
CH0036SQB-1 (36”)
23
CH-100 Series
MODEL NO.: CH0042SQB-1 (42”)
CH0048SQB-1 (48”)
24
RA-02 Series
MODEL NO.:
NO.
1
2
3
RA0230SQB-1 (30”)
RA0236SQB-1 (36”)
RA0242SQB-1 (42”)
RA0248SQB-1 (48”)
DESCRIPTION
6” Round Plastic Exhaust
8” Round Exhaust Plate
Duct Cover
Hood Mounting Bracket
4
Hood Casing
5
6
7
LED Light
Valve Stem
Knob
8
Oil Tunnel
9
Motor Mounting Bracket
10
Air Chamber & Motor
11
Safety Screen
12
Capacitor
13
Light Transformer
14
Capacitor Panel
15
16
A
B
C
D
Baffle Filter
Spacer
1” wide
4” wide
3/4” wide
3-3/4” wide
MODEL /SIZE
RA0230SQB-1 / RA0236SQB-1
RA0242SQB-1 / RA0248SQB-1
RA02DC
RA0230SQB-1
RA0236SQB-1
RA0242SQB-1
RA0248SQB-1
RA0230SQB-1
RA0236SQB-1
RA0242SQB-1
RA0248SQB-1
RA0230SQB-1 / RA0236SQB-1
RA0242SQB-1 / RA0248SQB-1
RA0230SQB-1 / RA0236SQB-1
RA0242SQB-1 / RA0248SQB-1
RA0230SQB-1 / RA0236SQB-1
RA0242SQB-1 / RA0248SQB-1
RA0230SQB-1 / RA0236SQB-1
RA0242SQB-1 / RA0248SQB-1
RA0230SQB-1
RA0236SQB-1
RA0242SQB-1
RA0248SQB-1
RA0230SQB-1
RA0236SQB-1
RA0242SQB-1
RA0248SQB-1
25
PART NO.
C1-0505-0001
C1-0606-0101
12-56000-012-51
C1-0221-0092
B101-5630-01
B101-5636-01
B101-5642-01
B101-5648-01
C1-0403-0306
C1-0405-0404-B
C1-0405-0400-A
B101-5630-14
B101-5636-14
B101-5642-14
B101-5648-14
C1-0105-2100-L
C1-0105-2142-L
C1-0302-A110-06
C1-0302-A120-01
C1-0302-A110-06-C
C1-0302-A120-01-C
C1-0401-A250-22
C1-0401-A300-08
C1-0402-D001
C1-0201-5630
C1-0201-5636
C1-0201-5642
C1-0201-5648
B101-1930-15
B101-5630-09
B101-5636-09
B101-5642-09
B101-5648-09
RA-02 Series
MODEL NO.:
RA0230SQB-1 (30”)
RA0236SQB-1 (36”)
26
RA-02 Series
MODEL NO.:
RA0242SQB-1 (42”)
RA0248SQB-1 (48”)
27
CIRCUIT DIAGRAM
CH-100 Series
MODEL NO.: CH0030SQB-1 (30”)
CH0036SQB-1 (36”)
CH0042SQB-1 (42”)
CH0048SQB-1 (48”)
RA-02 Series
MODEL NO.:
RA0230SQB-1 (30”)
RA0236SQB-1 (36”)
RA0242SQB-1 (42”)
RA0248SQB-1 (48”)
28
TROUBLE SHOOTING
Issue
After Installation,
both motors and
lights are not
working.
Possible Cause
The power is not on.
The wire connection is not secure.
The control panel is defective.
Solution
Make sure the circuit breaker and the unit’s power is
ON. Use a voltage meter to check the power supply.
Check and tighten wire connection.
Replace the control panel.
Lights are
working, but
motor(s) is not.
The motor(s) is defective.
The capacitor(s) is defective.
The control panel is defective.
Replace the motor.
Replace capacitor(s).
Replace the control panel.
The range
hood is
vibrating.
The blower system is not secure.
The motor is
working, but
the lights are
not working.
LED Light(s) is defective.
Tighten the turbine impeller/squirrel cage and air
chamber.
Replace the squirrel cage.
Check the installation of hood, tighten the
mounting bracket.
Replace the LED light.
The squirrel cage is not balanced.
Hood is not secured in place.
The light wiring(s) is loose.
Light transformer is defective.
The range
hood is not
venting out
correctly.
The control panel is defective.
The range hood is installed outside of
the manufacture recommended
clearance.
There is no make-up air inside the
house.
Obstacle blocking the pipe work.
The pipe size is smaller than the
suggested pipe size.
Cold air is
The pipe connection is not properly
coming into the sealed.
home.
The damper is not properly installed or
is missing from the installation.
The damper is not installed.
29
Check wire continuity from light transformer to
LED light housing(s).
Check power input and power output on the light
transformer. If it’s needed, replace the light
transformer.
Replace the control panel.
Adjust the clearance between the range hoods
and cook top to 27” to 30”. For Island range
hood, the clearance between the range hoods
and cook top is 30” to 36”.
Open the window to enhance the performance
of the range hood by creating a sufficient makeup air.
Remove all obstacles from the duct work.
Change the ducting according to the
manufacture suggestion.
Check the pipe installation.
Check the damper installation.
By installing the damper, it will help to eliminate
air backflow.
DISCLAIMER
1. CAREFULLY INSPECT ALL ITEMS FOR DAMAGES BEFORE ACCEPTING DELIVERY. NOTE
ANY DAMAGES ON THE FREIGHT BILL OR EXPRESS RECEIPT. REQUEST NAME AND
SIGNATURE OF THE CARRIER’S AGENT AND KEEP COPY TO SUPPORT YOUR CLAIM.
Upon acceptance of items, owner assumes responsibility for its safe arrival. Report damages to the
carrier and file a claim immediately. Failure to do so may result in the denial of your claim. The
carrier will furnish you with necessary forms for filing a claim.
DAMAGES CAUSED DURING TRANSIT ARE NOT COVERED UNDER OUR WARRANTY.
2. PLEASE INSPECT CONTENTS OF PACKAGE(S) CAREFULLY UPON RECEIVING!
We must be notified in writing of any damages and/or missing parts within the allocated days upon
your receipt of package(s). Contact your local KOBE dealer or distributor or call KOBE for the time
limit.
CLAIMS WILL NOT BE ACCEPTED AFTER THE ALLOCATED DAYS.
NOTE: ITEMS WERE THOROUGHLY TESTED AND CAREFULLY PACKED IN OUR FACTORY
BEFORE SHIPPING.
3. Products must be returned in good working condition with ALL original parts and documentation
packed in ALL original cartons, fillers and shipping cartons. A restocking fee of 25% will be charged
for all approved return(s).
EXCHANGES OR RETURNS MAY NOT BE ACCEPTED IF ANY PACKAGING IS MISSING.
4. MAKE SURE TO INSPECT THE HOOD FOR DAMAGES AND DEFECTS BEFORE
INSTALLATION. Appearance flaws of the hood found after installation and not affecting hood
performance is not covered under our warranty for returns or exchanges. Service visits not covered
under warranty will carry a service charge.
A)
Before Installation: Return for exchange or refund (please see above for acceptable
returns).
B)
After Installation:
NO exchange or refund.
30
WARRANTY
WARRANTY CERTIFICATE
KOBE Range Hoods warrants all products manufactured or supplied by it to be free from defects in
workmanship and materials. Its obligations pursuant to this warranty are limited to a period of two
years from the date of purchase and to the repair or replacement at its option and subject to the terms
and conditions stated below, of any component part, which its examination shall disclose to be so
defective.
TWO-YEAR WARRANTY SERVICE PERIOD
Any covered failure occurring within two years of original purchase arising from defective workmanship
or material in manufacture will be repaired (or at our discretion, replaced) free of charge by an
authorized KOBE Range Hoods Agent or KOBE Range Hoods as applicable. Keep proof of purchase
(or original invoice) handy for inspection.
If the range hood is sold by the original purchaser during the warranty period the new owner is
protected until expiration of the original purchaser’s warranty.
CONDITIONS
The following conditions apply only in relation to the warranty expressly given in this certificate.
1) This warranty applies only:
a) within U.S.A. and Canada.
b) to range hoods used for PRIVATE SINGLE FAMILY USE (if used for COMMERCIAL or
MULTIPLE FAMILY USE or other purposes, warranty will be voided).
2) Repair of any fault to be provided under this warranty shall not be provided:
a) if the identification number attached to the range hood has been altered, rendered illegible or
removed;
b) if notice of the defect has not been given within the period applicable;
c) for failure of light bulbs or heat lamps;
d) for physical damage;
e) for surfaces damaged by use of improper chemical cleaning agents;
f) if the appliance has been:
i) subject to misuse, abuse, negligence, accident, incorrect installation or failure to follow the
operating instructions;
ii) connected to improper, inadequate or faulty electricity service or exhaust ducts, flues or duct
cover, or operated using incorrect or contaminated lubricants;
iii) installed, maintained or operated otherwise than in accordance with the instructions
furnished by KOBE Range Hoods including the improper use of detergents, bleaches, or
cleaners.
g) for damage to range hood during transit, delivery, installation or removal;
h) for damage by or resulting from attempted repairs conducted by anyone other than our
Authorized Service Agent.
i) noise or vibration caused by improper installation of range hood and/or damper.
31
3) The purchaser shall be responsible for any expenses involved in making the range hood readily
accessible for servicing and where the range hood is installed outside the main sales territory of the
retailer or service territory of the nearest approved KOBE Range Hoods Agent as applicable, for any
traveling expenses and any costs of transporting the range hood or parts thereof to and from the
dealer or Service Agent
4) The purchaser must produce proof of purchase together with this warranty certificate when making
the claim.
5) Damages caused during shipment are not covered under our warranty.
CONSEQUENTIAL DAMAGE
The warrantor is not responsible for any consequential damage. SOME STATES DO NOT ALLOW
THE EXCLUSION OF CONSEQUENTIAL DAMAGE SO THE ABOVE EXCLUSION MAY NOT APPLY
TO YOU.
IMPLIED WARRANTIES/STATE LAW
Any implied warranties, including the implied warranty of merchantability and fitness for purpose,
imposed on the sale by the laws of the state of sale are limited to two year from the date of original
purchase. Some states do not allow limitations on the duration of implied warranties. This warranty
gives you specific legal rights, and may also have rights, which vary from state to state.
SERVICE
For service contact:
KOBE Range Hoods
11775 Clark Street
Arcadia, CA 91006
U.S.A.
Tel: (626) 775-8880
Email:
customer.service@KOBERangeHoods.com
Website:
www.KOBERangeHoods.com
32
PRODUCT REGISTRATION
Register Your Product!
Any covered failure occurring within two years of original purchase arising from defective
workmanship or material in manufacture will be repaired or at our option the unit will be replaced
free of charge by an authorized KOBE Range Hoods Agent or KOBE Range Hoods as applicable.
Keep proof of purchase (original invoice) handy for inspection.
If the range hood is sold by the original purchaser during the warranty period the new owner is
protected until expiration of the original purchaser’s warranty. See warranty section for complete
warranty coverage information.
This appliance has been manufactured, tested, and inspected to the standards required by KOBE
Range Hoods.
PLEASE MAIL IN YOUR WARRANTY REGISTRATION CARD AND PROOF OF PURCHASE TO:
KOBE Range Hoods
11775 Clark Street
Arcadia, CA 91006
U.S.A.
RECORD THE FOLLOWING INFORMATION FOR YOUR RECORD:
Model No. ________________________
Serial No. ________________________
Purchased Date
_____/_____/_____
Purchased From:
______________________________
______________________________
______________________________
IMPORTANT: PLEASE KEEP A COPY OF YOUR SALE RECEIPT OR INVOICE HANDY WHEN
REQUESTING FOR SERVICE.
33
KOBE Range Hoods
11775 Clark Street
Arcadia, CA 91006 USA
http://www.KOBERangeHoods.com
This KOBE hood is made for use in the USA and CANADA only. We do not recommend
using this hood overseas as the power supply may not be compatible and may violate
the electrical code of that country. Using a KOBE hood overseas is at your own risk
and will void your warranty.
Information subject to change without notice.
VER.111109
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising