Wolf | VI42S | Remote Blower Installation Guide | Wolf VI42S Remote Blower Installation Guide

MODEL 801640
Page 1
EXTERIOR VENTILATOR KITS
!
WARNING
CAUTION
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer or your
distributor.
2. Before servicing or cleaning unit, switch power off at service
panel and lock the service disconnecting means to prevent
power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten
a prominent warning device, such as a tag, to the service
panel.
3. Installation work and electrical wiring must be done by a
qualified person(s) in accordance with all applicable codes
and standards, including fire-rated construction codes and
standards.
4. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment
manufacturer’s guidelines and safety standards such as
those published by the National Fire Protection Association
(NFPA), and the American Society for Heating, Refrigeration
and Air Conditioning Engineers (ASHRAE), and the local
code authorities.
5. When cutting or drilling into wall or ceiling, do not damage
electrical wiring and other hidden utilities.
6. Ducted fans must always be vented to the outdoors.
7. Do not use this unit with an additional speed control device.
8. To reduce the risk of fire, use only steel ductwork.
9. This unit must be grounded.
TO REDUCE THE RISK OF A COOKTOP GREASE FIRE:
1. Never leave surface units unattended at high settings.
Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings.
2. Always turn hood ON when cooking at high heat or when
cooking flaming foods.
3. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter.
4. Use proper pan size. Always use cookware appropriate for
the size of the surface element.
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE
EVENT OF A COOKTOP GREASE FIRE, OBSERVE THE
FOLLOWING:*
1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or
metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately,
EVACUATE AND CALL THE FIRE DEPARTMENT.
2. NEVER PICK UP A FLAMING PAN - You may be burned.
3. DO NOT USE WATER, including wet dishcloths or towels violent steam explosion will result.
4. Use an extinguisher ONLY if:
A. You know you have a Class ABC extinguisher and you
already know how to operate it.
B. The fire is small and contained in the area where it started.
C. The fire department is being called.
D. You can fight the fire with your back to an exit.
* Based on “Kitchen Fire Safety Tips” published by NFPA.
1. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.
2. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray, construction dust, etc.
off power unit.
3. Your ventilator motor has a thermal overload which will automatically shut off the motor if it becomes overheated. The
motor will restart when it cools down. If the motor continues to
shut off and restart, have the hood serviced.
4. Please read specification label on product for further information and requirements.
SPECIFICATIONS
MODEL
801640
VOLTS
120
AMPS
2.4
CFM
600
DUCT SIZE
10 "DIA.
PLAN THE INSTALLATION
1. Locate the ventilator so the length of the duct run and number
of elbows and transitions needed are kept to a minimum.
2. Where possible, ventilator should be located between wall
studs or roof rafters.
3. Avoid pipes, wires, or other ductwork that may be running
through the wall.
4. Be sure that there is enough space for any transitions that may
be needed between the ventilator and the connecting
ductwork.
5. For best performance, locate transitions nearest to ventilator.
MODEL 801640
ROOF MOUNT
Page 2
INSTALLATION
For use with Wolf CTWH30/CTWH36 wall mount, IH4227 island chimney hoods, 10” tall & 30” wide x 18” tall wall hoods.
WIRE THE VENTILATOR
PREPARE THE ROOF
BLACK
TO
BLACK
20¾"
8½"
Rafter
Pilot
Hole
Roof
Roof
10 3 /8 "
Rafter
REMOVE
SHINGLES
1¼"
dia. hole
11"
dia.
hole
120 VAC
LINE IN
20½"
q5
9 1 /8 "
q6
q7
7¼"
GREEN
TO
GREEN
Remove 7 COVER SCREWS and lift off ventilator cover.
Remove BIRD SCREEN and WIRING COVER.
Feed the electric power cable through the 1¼" DIAMETER
HOLE and connect cable to ventilator with a proper
connector for the type of cable being used.
Connect BLACK TO BLACK, WHITE TO WHITE, and the
GREEN TO GREEN or bare wire. Replace wiring cover.
INSTALL THE VENTILATOR
OUTSIDE - ROOF VIEW
From inside the attic space:
q 1 Drill a PILOT HOLE up through the roof, 8½" from the
inside edge of a ROOF RAFTER.
6
Mounting
Holes
7 Cover
Screws
From outside - on the roof:
q 2 Measure and mark the 20¾" x 20½" rectangle. Cut and
remove only the shingles inside this rectangle.
q 3 Measure and mark the 11" DIAMETER HOLE and the
1¼" DIAMETER HOLE. Cut these holes all the way through
the roof.
Shipping
Cardboard
2"
2
WHITE
TO
WHITE
Remove
roofing
nails from
top 2/3 of
shingles.
Wiring
Cover
Bird Screen
"
9½
7"
Flashing Sheet
OUTSIDE - ROOF VIEW
25"
2"
q8
q9
q
For flat roof installations:
q 4 Build a curb that will mount the blower at a minimum pitch
of 2/12. Discharge end of the blower should be pointed
away from prevailing winds.
q
q
q
Remove SHIPPING CARDBOARD from blower wheel.
Remove roofing nails from top 2/3 of shingles around cutout area.
10 Slide the ventilator's FLASHING SHEET up and under
the loosened shingles until ventilator's discharge collar
fits into 11" diameter hole.
11 Use the 6 screws (provided) to attach the ventilator to the
roof. 6 MOUNTING HOLES are provided.
12 Seal the screw heads, loosened shingles, and edges of
the flashing sheet, with a good grade of roofing cement.
13 Check for free movement of the spring-loaded damper,
re-install BIRD SCREEN and ventilator cover. Turn on
power and check operation.
MODEL 801640
Page 3
INSTALLATION
WALL MOUNT
For use with Wolf CTWH30/CTWH36 wall mount, IH4227 island chimney hoods, 10” tall & 30” wide x 18” tall wall hoods.
WIRE THE VENTILATOR
PREPARE THE WALL
BLACK
TO
BLACK
25"
10¾"
REMOVE
SIDING
11" dia.
hole
Pilot
Hole
120 VAC
LINE IN
Wall Stud
12 7 /8 "
Wall Stud
8½"
1¼"
dia. hole
29½"
9 1 /8 "
q4
q5
q6
WHITE
TO
WHITE
GREEN
TO
GREEN
Remove 7 COVER SCREWS and lift off ventilator cover.
Remove BIRD SCREEN and WIRING COVER.
Feed the electric power cable through the 1¼" DIAMETER
HOLE and connect cable to ventilator with a proper
connector for the type of cable being used.
Connect BLACK TO BLACK, WHITE TO WHITE, and the
GREEN TO GREEN or bare wire. Replace wiring cover.
7¼"
INSTALL THE VENTILATOR
OUTSIDE - WALL VIEW
From inside the wall:
q 1 Drill a PILOT HOLE through the wall, 8½" from the inside
edge of a WALL STUD.
6
Mounting
Holes
7 Cover
Screws
From outside - on the wall:
q 2 Measure and mark the 25" x 29½" rectangle. Cut and
remove only the siding inside this rectangle.
q 3 Measure and mark the 11" DIAMETER HOLE and the
1¼" DIAMETER HOLE. Cut these holes all the way
through the wall.
Shipping
Cardboard
Wiring
Cover
Bird Screen
Flashing Sheet
OUTSIDE - WALL VIEW
q7
q8
q
q
q
Remove SHIPPING CARDBOARD from blower wheel.
Place ventilator on wall so that ventilator's discharge collar
fits into 11" diameter hole.
9 Use the 6 screws (provided) to attach the ventilator to the
wall. 6 MOUNTING HOLES are provided.
10 Seal the screw heads and edges of the flashing sheet
with a good grade of roofing cement.
11 Check for free movement of the spring-loaded damper,
re-install BIRD SCREEN and ventilator cover. Turn on
power and check operation.
MODEL 801640
Page 4
ATTACH POWER CORD TO HOOD
Some hoods require the use of a separate power cord and strain relief bushing (included), for proper
wiring of exterior blowers. Please refer to the hood manual for proper installation instructions.
MODEL 801641
Page 1
EXTERIOR VENTILATOR KITS
!
WARNING
CAUTION
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer or your
distributor.
2. Before servicing or cleaning unit, switch power off at service
panel and lock the service disconnecting means to prevent
power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten
a prominent warning device, such as a tag, to the service
panel.
3. Installation work and electrical wiring must be done by a
qualified person(s) in accordance with all applicable codes
and standards, including fire-rated construction codes and
standards.
4. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment
manufacturer’s guidelines and safety standards such as
those published by the National Fire Protection Association
(NFPA), and the American Society for Heating, Refrigeration
and Air Conditioning Engineers (ASHRAE), and the local
code authorities.
5. When cutting or drilling into wall or ceiling, do not damage
electrical wiring and other hidden utilities.
6. Ducted fans must always be vented to the outdoors.
7. Do not use this unit with an additional speed control device.
8. To reduce the risk of fire, use only steel ductwork.
9. This unit must be grounded.
TO REDUCE THE RISK OF A COOKTOP GREASE FIRE:
1. Never leave surface units unattended at high settings.
Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings.
2. Always turn hood ON when cooking at high heat or when
cooking flaming foods.
3. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter.
4. Use proper pan size. Always use cookware appropriate for
the size of the surface element.
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE
EVENT OF A COOKTOP GREASE FIRE, OBSERVE THE
FOLLOWING:*
1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or
metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately,
EVACUATE AND CALL THE FIRE DEPARTMENT.
2. NEVER PICK UP A FLAMING PAN - You may be burned.
3. DO NOT USE WATER, including wet dishcloths or towels violent steam explosion will result.
4. Use an extinguisher ONLY if:
A. You know you have a Class ABC extinguisher and you
already know how to operate it.
B. The fire is small and contained in the area where it started.
C. The fire department is being called.
D. You can fight the fire with your back to an exit.
* Based on “Kitchen Fire Safety Tips” published by NFPA.
1. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.
2. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray, construction dust, etc.
off power unit.
3. Your ventilator motor has a thermal overload which will automatically shut off the motor if it becomes overheated. The
motor will restart when it cools down. If the motor continues to
shut off and restart, have the hood serviced.
4. Please read specification label on product for further information and requirements.
SPECIFICATIONS
MODEL
801641
VOLTS
120
AMPS
5.7
CFM
900
DUCT SIZE
10 "DIA.
PLAN THE INSTALLATION
1. Locate the ventilator so the length of the duct run and number
of elbows and transitions needed are kept to a minimum.
2. Where possible, ventilator should be located between wall
studs or roof rafters.
3. Avoid pipes, wires, or other ductwork that may be running
through the wall.
4. Be sure that there is enough space for any transitions that may
be needed between the ventilator and the connecting
ductwork.
5. For best performance, locate transitions nearest to ventilator.
MODEL 801641
ROOF MOUNT
Page 2
INSTALLATION
For use with Wolf CTWH30/CTWH36 wall mount, IH4227 island chimney hoods, DD30R/DD36R downdraft ventilators, 10” tall
& 30-54” wide x 18” tall wall hoods, 36-54” x 18” tall island hoods & 12” tall liners.
WIRE THE VENTILATOR
PREPARE THE ROOF
BLACK
TO
BLACK
20¾"
8½"
Rafter
Pilot
Hole
Roof
Roof
10 3 /8 "
Rafter
REMOVE
SHINGLES
1¼"
dia. hole
11"
dia.
hole
120 VAC
LINE IN
20½"
q5
9 1 /8 "
q6
q7
7¼"
GREEN
TO
GREEN
Remove 7 COVER SCREWS and lift off ventilator cover.
Remove BIRD SCREEN and WIRING COVER.
Feed the electric power cable through the 1¼" DIAMETER
HOLE and connect cable to ventilator with a proper
connector for the type of cable being used.
Connect BLACK TO BLACK, WHITE TO WHITE, and the
GREEN TO GREEN or bare wire. Replace wiring cover.
INSTALL THE VENTILATOR
OUTSIDE - ROOF VIEW
From inside the attic space:
q 1 Drill a PILOT HOLE up through the roof, 8½" from the
inside edge of a ROOF RAFTER.
6
Mounting
Holes
7 Cover
Screws
From outside - on the roof:
q 2 Measure and mark the 20¾" x 20½" rectangle. Cut and
remove only the shingles inside this rectangle.
q 3 Measure and mark the 11" DIAMETER HOLE and the
1¼" DIAMETER HOLE. Cut these holes all the way through
the roof.
Shipping
Cardboard
2"
2
WHITE
TO
WHITE
Remove
roofing
nails from
top 2/3 of
shingles.
Wiring
Cover
Bird Screen
"
9½
7"
Flashing Sheet
OUTSIDE - ROOF VIEW
25"
2"
q8
q9
q
For flat roof installations:
q 4 Build a curb that will mount the blower at a minimum pitch
of 2/12. Discharge end of the blower should be pointed
away from prevailing winds.
q
q
q
Remove SHIPPING CARDBOARD from blower wheel.
Remove roofing nails from top 2/3 of shingles around cutout area.
10 Slide the ventilator's FLASHING SHEET up and under
the loosened shingles until ventilator's discharge collar
fits into 11" diameter hole.
11 Use the 6 screws (provided) to attach the ventilator to the
roof. 6 MOUNTING HOLES are provided.
12 Seal the screw heads, loosened shingles, and edges of
the flashing sheet, with a good grade of roofing cement.
13 Check for free movement of the spring-loaded damper,
re-install BIRD SCREEN and ventilator cover. Turn on
power and check operation.
MODEL 801641
Page 3
INSTALLATION
WALL MOUNT
For use with Wolf CTWH30/CTWH36 wall mount, IH4227 island chimney hoods, DD30R/DD36R downdraft ventilators, 10” tall
& 30-54” wide x 18” tall wall hoods, 36-54” x 18” tall island hoods & 12” tall liners.
WIRE THE VENTILATOR
PREPARE THE WALL
BLACK
TO
BLACK
25"
10¾"
REMOVE
SIDING
11" dia.
hole
Pilot
Hole
120 VAC
LINE IN
Wall Stud
12 7 /8 "
Wall Stud
8½"
1¼"
dia. hole
29½"
9 1 /8 "
q4
q5
q6
WHITE
TO
WHITE
GREEN
TO
GREEN
Remove 7 COVER SCREWS and lift off ventilator cover.
Remove BIRD SCREEN and WIRING COVER.
Feed the electric power cable through the 1¼" DIAMETER
HOLE and connect cable to ventilator with a proper
connector for the type of cable being used.
Connect BLACK TO BLACK, WHITE TO WHITE, and the
GREEN TO GREEN or bare wire. Replace wiring cover.
7¼"
INSTALL THE VENTILATOR
OUTSIDE - WALL VIEW
From inside the wall:
q 1 Drill a PILOT HOLE through the wall, 8½" from the inside
edge of a WALL STUD.
6
Mounting
Holes
7 Cover
Screws
From outside - on the wall:
q 2 Measure and mark the 25" x 29½" rectangle. Cut and
remove only the siding inside this rectangle.
q 3 Measure and mark the 11" DIAMETER HOLE and the
1¼" DIAMETER HOLE. Cut these holes all the way
through the wall.
Shipping
Cardboard
Wiring
Cover
Bird Screen
Flashing Sheet
OUTSIDE - WALL VIEW
q7
q8
q
q
q
Remove SHIPPING CARDBOARD from blower wheel.
Place ventilator on wall so that ventilator's discharge collar
fits into 11" diameter hole.
9 Use the 6 screws (provided) to attach the ventilator to the
wall. 6 MOUNTING HOLES are provided.
10 Seal the screw heads and edges of the flashing sheet
with a good grade of roofing cement.
11 Check for free movement of the spring-loaded damper,
re-install BIRD SCREEN and ventilator cover. Turn on
power and check operation.
MODEL 801641
Page 4
ATTACH POWER CORD TO HOOD
Some hoods require the use of a separate power cord and strain relief bushing (included), for proper
wiring of exterior blowers. Please refer to the hood manual for proper installation instructions.
MODEL 801642
Page 1
EXTERIOR VENTILATOR KITS
!
WARNING
CAUTION
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer or your
distributor.
2. Before servicing or cleaning unit, switch power off at service
panel and lock the service disconnecting means to prevent
power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten
a prominent warning device, such as a tag, to the service
panel.
3. Installation work and electrical wiring must be done by a
qualified person(s) in accordance with all applicable codes
and standards, including fire-rated construction codes and
standards.
4. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment
manufacturer’s guidelines and safety standards such as
those published by the National Fire Protection Association
(NFPA), and the American Society for Heating, Refrigeration
and Air Conditioning Engineers (ASHRAE), and the local
code authorities.
5. When cutting or drilling into wall or ceiling, do not damage
electrical wiring and other hidden utilities.
6. Ducted fans must always be vented to the outdoors.
7. Do not use this unit with an additional speed control device.
8. To reduce the risk of fire, use only steel ductwork.
9. This unit must be grounded.
TO REDUCE THE RISK OF A COOKTOP GREASE FIRE:
1. Never leave surface units unattended at high settings.
Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings.
2. Always turn hood ON when cooking at high heat or when
cooking flaming foods.
3. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter.
4. Use proper pan size. Always use cookware appropriate for
the size of the surface element.
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE
EVENT OF A COOKTOP GREASE FIRE, OBSERVE THE
FOLLOWING:*
1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or
metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately,
EVACUATE AND CALL THE FIRE DEPARTMENT.
2. NEVER PICK UP A FLAMING PAN - You may be burned.
3. DO NOT USE WATER, including wet dishcloths or towels violent steam explosion will result.
4. Use an extinguisher ONLY if:
A. You know you have a Class ABC extinguisher and you
already know how to operate it.
B. The fire is small and contained in the area where it started.
C. The fire department is being called.
D. You can fight the fire with your back to an exit.
* Based on “Kitchen Fire Safety Tips” published by NFPA.
1. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.
2. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray, construction dust, etc.
off power unit.
3. Your ventilator motor has a thermal overload which will automatically shut off the motor if it becomes overheated. The
motor will restart when it cools down. If the motor continues to
shut off and restart, have the hood serviced.
4. Please read specification label on product for further information and requirements.
SPECIFICATIONS
MODEL
801642
VOLTS
120
AMPS
3.0
CFM
1200
DUCT SIZE
10" DIA.
PLAN THE INSTALLATION
1. Locate the ventilator so the length of the duct run and number
of elbows and transitions needed are kept to a minimum.
2. Where possible, ventilator should be located between wall
studs or roof rafters.
3. Avoid pipes, wires, or other ductwork that may be running
through the wall.
4. Be sure that there is enough space for any transitions that may
be needed between the ventilator and the connecting
ductwork.
5. For best performance, locate transitions nearest to ventilator.
MODEL 801642
ROOF MOUNT
Page 2
INSTALLATION
For use with Wolf CTWH30/CTWH36 wall mount, IH4227 island chimney hoods, DD30R/DD36R downdraft ventilators, 18” tall
island/wall hoods & 12” tall liners.
WIRE THE VENTILATOR
PREPARE THE ROOF
q5
15"
q6
1¼" dia. hole
REMOVE SHINGLES
1"
Pilot Hole
(centered
between rafters)
Roof Rafter
Roof Rafter
12 11 /16 "
20½"
q7
11" dia.
hole
Remove 10
COVER SCREWS
and lift off
ventilator cover.
Feed the electric
power cable
through the 1¼"
DIAMETER HOLE
and connect cable
to ventilator with a
proper connector
for the type of
cable being used.
Connect BLACK
TO BLACK,
WHITE TO BLUE,
and GROUND TO
GROUNDING
SCREW.
GROUND
TO
GROUNDING
SCREW
WHITE
TO
BLUE
120
VAC
LINE
IN
BLACK TO BLACK
11 / 16 "
9 13
INSTALL THE VENTILATOR
18"
10 Cover
Screws
From inside the attic space:
q 1 Drill a PILOT HOLE up through the roof, centered between
ROOF RAFTERS.
From outside - on the roof:
q 2 Measure and mark the 18" x 20½" rectangle. Cut and
remove only the shingles inside this rectangle.
q 3 Measure and mark the 11" DIAMETER HOLE and the
1¼" DIAMETER HOLE. Cut these holes all the way through
the roof.
Remove
roofing
nails from
top 2/3 of
shingles.
Flashing
Sheet
2"
29
Drill 6
Mounting
Holes
Damper
½"
Bird Screen
7"
OUTSIDE - ROOF VIEW
q8
22"
2"
For flat roof installations:
q 4 Build a curb that will mount the blower at a minimum pitch
of 2/12. Discharge end of the blower should be pointed
away from prevailing winds.
q
q
q
q
Remove roofing nails from top 2/3 of shingles around
cut-out area.
9 Slide the ventilator's FLASHING SHEET up and under
the loosened shingles until ventilator's discharge collar
fits into 11" diameter hole.
10 Use the 6 screws (provided) to attach the ventilator to
the roof. DRILL 6 MOUNTING HOLES inside the
ventilator, as necessary.
11 Seal the screw heads, loosened shingles, and edges
of the flashing sheet, with a good grade of roofing
cement.
12 Check for free movement of the spring-loaded
DAMPER, and re-install the ventilator cover. Turn on
power and check operation.
MODEL 801642
Page 3
INSTALLATION
WALL MOUNT
For use with Wolf CTWH30/CTWH36 wall mount, IH4227 island chimney hoods, DD30R/DD36R downdraft ventilators, 18” tall
island/wall hoods & 12” tall liners.
WIRE THE VENTILATOR
PREPARE THE WALL
q4
17"
q5
1¼" dia. hole
14 11 /16 "
Pilot Hole
(centered between studs)
3"
REMOVE
SIDING
11" dia.
hole
q6
Wall Stud
Wall Stud
29½"
Remove 10
COVER SCREWS
and lift off
ventilator cover.
Feed the electric
power cable
through the 1¼"
DIAMETER HOLE
and connect cable
to ventilator with a
proper connector
for the type of
cable being used.
Connect BLACK
TO BLACK,
WHITE TO BLUE,
and GROUND TO
GROUNDING
SCREW.
GROUND
TO
GROUNDING
SCREW
WHITE
TO
BLUE
120
VAC
LINE
IN
BLACK TO BLACK
INSTALL THE VENTILATOR
13/16
11 13
16"
Drill 6
Mounting
Holes
10 Cover
Screws
22"
From inside the wall:
q 1 Drill a PILOT HOLE through the wall, centered between
WALL STUDS.
From outside - on the wall:
q 2 Measure and mark the 22" x 29½" rectangle. Cut and
remove only the siding inside this rectangle.
q 3 Measure and mark the 11" DIAMETER HOLE and the
1¼" DIAMETER HOLE. Cut these holes all the way through
the wall.
Flashing
Sheet
Damper
Bird Screen
OUTSIDE - WALL
ROOF VIEW
q7
q
q
q
Place ventilator on wall so that ventilator's discharge collar
fits into 11" diameter hole.
8 Use the 6 screws (provided) to attach the ventilator to the
wall. DRILL 6 MOUNTING HOLES inside the ventilator, as
necessary.
Seal
the screw heads and edges of the flashing sheet with
9
a good grade of roofing cement.
10 Check for free movement of the spring-loaded DAMPER
and re-install ventilator cover. Turn on power and check
operation.
MODEL 801642
Page 4
ATTACH POWER CORD TO HOOD
Some hoods require the use of a separate power cord and strain relief bushing (included), for proper
wiring of exterior blowers. Please refer to the hood manual for proper installation instructions.
MODEL 804701
Page 1
EXTERIOR VENTILATOR KITS
!
WARNING
CAUTION
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer or your
distributor.
2. Before servicing or cleaning unit, switch power off at service
panel and lock the service disconnecting means to prevent
power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten
a prominent warning device, such as a tag, to the service
panel.
3. Installation work and electrical wiring must be done by a
qualified person(s) in accordance with all applicable codes
and standards, including fire-rated construction codes and
standards.
4. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment
manufacturer’s guidelines and safety standards such as
those published by the National Fire Protection Association
(NFPA), and the American Society for Heating, Refrigeration
and Air Conditioning Engineers (ASHRAE), and the local
code authorities.
5. When cutting or drilling into wall or ceiling, do not damage
electrical wiring and other hidden utilities.
6. Ducted fans must always be vented to the outdoors.
7. Do not use this unit with an additional speed control device.
8. To reduce the risk of fire, use only steel ductwork.
9. This unit must be grounded.
TO REDUCE THE RISK OF A COOKTOP GREASE FIRE:
1. Never leave surface units unattended at high settings.
Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings.
2. Always turn hood ON when cooking at high heat or when
cooking flaming foods.
3. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter.
4. Use proper pan size. Always use cookware appropriate for
the size of the surface element.
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE
EVENT OF A COOKTOP GREASE FIRE, OBSERVE THE
FOLLOWING:*
1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or
metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately,
EVACUATE AND CALL THE FIRE DEPARTMENT.
2. NEVER PICK UP A FLAMING PAN - You may be burned.
3. DO NOT USE WATER, including wet dishcloths or towels violent steam explosion will result.
4. Use an extinguisher ONLY if:
A. You know you have a Class ABC extinguisher and you
already know how to operate it.
B. The fire is small and contained in the area where it started.
C. The fire department is being called.
D. You can fight the fire with your back to an exit.
* Based on “Kitchen Fire Safety Tips” published by NFPA.
1. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.
2. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray, construction dust, etc.
off power unit.
3. Your ventilator motor has a thermal overload which will automatically shut off the motor if it becomes overheated. The
motor will restart when it cools down. If the motor continues to
shut off and restart, have the hood serviced.
4. Please read specification label on product for further information and requirements.
SPECIFICATIONS
MODEL
804701
VOLTS
120
AMPS
3.8
CFM
1500
DUCT SIZE
10" DIA.
PLAN THE INSTALLATION
1. Locate the ventilator so the length of the duct run and number
of elbows and transitions needed are kept to a minimum.
2. Where possible, ventilator should be located between wall
studs or roof rafters.
3. Avoid pipes, wires, or other ductwork that may be running
through the wall.
4. Be sure that there is enough space for any transitions that may
be needed between the ventilator and the connecting
ductwork.
5. For best performance, locate transitions nearest to ventilator.
MODEL 804701
ROOF MOUNT
Page 2
INSTALLATION
For use with Wolf CTWH30/CTWH36 wall mount, IH4227 island chimney hoods, DD30R/DD36R downdraft ventilators, 18” tall
island/wall hoods & 12” tall liners.
WIRE THE VENTILATOR
PREPARE THE ROOF
q5
18"
q6
1¼" dia. hole
REMOVE SHINGLES
1"
Pilot Hole
(centered
between rafters)
Roof Rafter
Roof Rafter
12 11 /16 "
20½"
q7
11" dia.
hole
Remove 10
COVER SCREWS
and lift off
ventilator cover.
Feed the electric
power cable
through the 1¼"
DIAMETER HOLE
and connect cable
to ventilator with a
proper connector
for the type of
cable being used.
Connect BLACK
TO BLUE, WHITE
TO BROWN, and
GROUND TO
GROUNDING
SCREW.
GROUND
TO
GROUNDING
SCREW
WHITE
TO
BROWN
120
VAC
LINE
IN
BLACK TO BLUE
INSTALL THE VENTILATOR
115/ /16
912
8"
Drill 6
Mounting
Holes
21"
18"
10 Cover
Screws
From inside the attic space:
q 1 Drill a PILOT HOLE up through the roof, centered between
ROOF RAFTERS.
From outside - on the roof:
Measure and mark the 21" x 20½" rectangle. Cut and
remove only the shingles inside this rectangle.
q 3 Measure and mark the 11" DIAMETER HOLE and the
1¼" DIAMETER HOLE. Cut these holes all the way
through the roof.
Remove
roofing
nails from
top 2/3 of
shingles.
q2
Flashing
Sheet
Damper
2"
29
Bird Screen
½"
7"
OUTSIDE - ROOF VIEW
q8
25"
q
2"
For flat roof installations:
q 4 Build a curb that will mount the blower at a minimum pitch
of 2/12. Discharge end of the blower should be pointed
away from prevailing winds.
q
q
q
Remove roofing nails from top 2/3 of shingles around cutout area.
Slide
the ventilator's FLASHING SHEET up and under the
9
loosened shingles until ventilator's discharge collar fits
into 11" diameter hole.
10 Use the 6 screws (provided) to attach the ventilator to the
roof. DRILL 6 MOUNTING HOLES inside the ventilator,
as necessary.
11 Seal the screw heads, loosened shingles, and edges of
the flashing sheet, with a good grade of roofing cement.
12 Check for free movement of the spring-loaded DAMPER,
and re-install the ventilator cover. Turn on power and
check operation.
MODEL 804701
Page 3
INSTALLATION
WALL MOUNT
For use with Wolf CTWH30/CTWH36 wall mount, IH4227 island chimney hoods, DD30R/DD36R downdraft ventilators, 18” tall
island/wall hoods & 12” tall liners.
WIRE THE VENTILATOR
PREPARE THE WALL
q4
20"
17"
q5
1¼" dia. hole
14 11 /16 "
Pilot Hole
(centered between studs)
3"
q6
REMOVE
SIDING
11" dia.
hole
Wall Stud
Wall Stud
29½"
Remove 10
COVER SCREWS
and lift off
ventilator cover.
Feed the electric
power cable
through the 1¼"
DIAMETER HOLE
and connect cable
to ventilator with a
proper connector
for the type of
cable being used.
Connect BLACK
TO BLUE, WHITE
TO BROWN, and
GROUND TO
GROUNDING
SCREW.
GROUND
TO
GROUNDING
SCREW
WHITE
TO
BROWN
120
VAC
LINE
IN
BLACK TO BLUE
INSTALL THE VENTILATOR
11
14135 / 16
8 ""
Drill 6
Mounting
Holes
10 Cover
Screws
22"
25"
From inside the wall:
q 1 Drill a PILOT HOLE through the wall, centered between
WALL STUDS.
From outside - on the wall:
q 2 Measure and mark the 25" x 29½" rectangle. Cut and
remove only the siding inside this rectangle.
q 3 Measure and mark the 11" DIAMETER HOLE and the
1¼" DIAMETER HOLE. Cut these holes all the way through
the wall.
Flashing
Sheet
Damper
Bird Screen
OUTSIDE - WALL
ROOF VIEW
q7
q
q
q
Place ventilator on wall so that ventilator's discharge collar
fits into 11" diameter hole.
8 Use the 6 screws (provided) to attach the ventilator to the
wall. DRILL 6 MOUNTING HOLES inside the ventilator, as
necessary.
9 Seal the screw heads and edges of the flashing sheet with
a good grade of roofing cement.
10 Check for free movement of the spring-loaded DAMPER
and re-install ventilator cover. Turn on power and check
operation.
MODEL 804701
Page 4
ATTACH POWER CORD TO HOOD
Some hoods require the use of a separate power cord and strain relief bushing (included), for proper
wiring of exterior blowers. Please refer to the hood manual for proper installation instructions.
Download PDF

advertising