Windster | RA60TB30SS | User manual | Windster RA60TB30SS User Manual

Windster RA60TB30SS User Manual
TABLE OF CONTENTS
1
Table of Contents
www.windsterhood.com
Safety Information ................................................................ 2 – 3
User’s Manual
Content Checklist ....................................................................... 4
WALL MOUNT SERIES
Measurements ............................................................................ 5
RA-60TB30SS
RA-60TB36SS
RA-60TB42SS
RA-60TB48SS
NOTE: PLEASE INSPECT HOOD
IMMEDIATELY UPON RECEIVING.
CLAIM OF DAMAGE AFTER 7 DAYS
OF DELIVERY WILL BE DENIED.
This unit is designed for indoor
residential use only. DO NOT USE
OVER A WOOD GRILL OR MOUNT
IN OUTDOOR ENVIRONMENT.
Preparation ................................................................................ 6
Installation ............................................................................ 7 – 8
Installation Diagram ................................................................... 9
Operation & Features ....................................................... 10 – 11
Cleaning & Maintenance .......................................................... 12
Troubleshooting ....................................................................... 13
Part List / Replacement ........................................................... 14
Please read this operation manual thoroughly before
using your range hood. Store it in a safe location for
when you need to reference it in the future.
Warranty / Contact Us ...................................................... 15 – 16
2
SAFETY INFORMATION
SAFETY INFORMATION
SAFETY INFORMATION
TO REDUCE THE RISK OF A FIRE, ELECTRICAL SHOCK,
AND/OR INJURY OBSERVE THE FOLLOWING:




Unit is intended for indoor residential use only. If you should have questions,
contact the manufacturer at the address or telephone number listed in the
warranty.
In case the unit should need to be cleaned or repaired, switch power off at
service panel and lock service disconnecting means to prevent power from
being switched on accidentally. When the service disconnecting means cannot
be locked, securely fasten a prominent warning device, such as a tag, to the
service panel.
Installation work and electrical wiring must be done by a qualified technician in
accordance with all applicable codes and standards, including fire-rated
construction.
Sufficient air is needed for proper combustion and exhausting of gases
through the flue (chimney) of fuel burning equipment to prevent back drafting.
Follow the heating equipment manufacturer’s guideline and safety standards
such as those published by the National Fire Protection Association (NFPA),
and the American Society of Heating, Refrigeration and Air Conditioning
Engineers (ASHRAE), and the local code authorities.
3
TO REDUCE THE RISK OF FIRE, OR ELECTRIC SHOCK, DO NOT
USE THIS FAN WITH ANY SOLID-STATE SPEED CONTROL DEVICE.

Regardless of heat level, never leave any surface materials unattended while
operating an open flame.

Always turn hood ON when cooking at high heat or when flambéing food (i.e.
Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambé).

Depending on amount of usage, clean ventilating fans and filters frequently.
Grease should not be allowed to accumulate on fan or filter. For instructions
on the how to clean, see maintenance page.

Never leave surface units unattended at high settings. Boil-overs may cause
smoking and greasy spillovers may ignite as result. Heat oils slowly on low or
medium settings.

Use proper pan size. Always use cookware appropriate for the size of the
surface element.
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE
EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE
FOLLOWING:

SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then
turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not
go out immediately, EVACUATE AND CALL 911.

NEVER PICK UP A FLAMING PAN —Doing so may result in serious burns
and possibly spread the fire.
Before you begin to cut or drill into the wall, verify that there is no electrical
wiring or any other hidden electrical components.
Ducted fans must always be vented to the outdoors.

DO NOT USE WATER – Grease fire must be extinguished before further
action may be taken. Using water will agitate the grease and may cause a
violent steam explosion.

The unit must be properly grounded and installed at the recommended height
before beginning operation.


To reduce the risk of fire, use only metal ductwork.
Use a Fire Extinguisher ONLY if:
 You know you have a Class ABC extinguisher, and you already know
how to operate it.
 The fire is small and contained in the area where it started.
 The fire department is being called.
 You are able to safely control the fire with your back to an open exit. *



Because the unit is made of stainless steel, it may contain sharp edges.
Be careful to avoid cuts and abrasions by wearing protective gloves during
installation and cleaning.
CAUTION: FOR GENERAL VENTILATING USE ONLY. DO NOT
USE TO EXHAUST HAZARDOUS OR EXPLOSIVE MATERIALS
AND VAPORS
Based on “Kitchen Fire safety Tips” published by NFPA.
4
CONTENT CHECKLIST
CONTENT CHECKLIST
1. CONTENTS INCLUDED
a.
(1) RA-60TB series (30”, 36”, 42” or 48”) hood assembly
b.
(1) Lower duct cover (18-3/16”)
c.
(1) Upper duct cover (18-1/16”)
d.
(1) User’s manual
e.
(1) 6” – 7” transition collar
f.
(2) Baffle filters (RA-60TB 30” model only)
g.
(3) Baffle filters (RA-60TB 36” / 42” model only)
h.
(4) Baffle filters (RA-60TB 48” model only)
i.
(1) Screw packet
j.
(1) Duct cover bracket
2. CONTENTS NOT INCLUDED
a.
RA-60TBEXTDC (Extension duct cover)
b.
RA-60TBDK (Ductless kit)
c.
RA-60TBCFMR (CFM reducer)
d.
RA-60TBCF (Charcoal filter for ductless operation only)
e.
6” / 7” round solid metal duct or flexible aluminum duct
3. TOOLS REQUIRED (NOT INCLUDED)
a.
Safety gloves
b.
Safety glasses
c.
Electric drill w/ starter bit
d.
Utility knife
e.
Spirit level
f.
Measuring tape
g.
Writing instrument (pen, marker, pencil)
h.
Aluminum tape
MEASUREMENTS
5
6
INSTALLATION
PREPARATION
PREPARATION
1. BEFORE YOU START
INSTALLATION
1. WALL MOUNT INSTALLATION
**BE SURE YOUR UNIT WILL FIT YOUR CEILING HEIGHT**
a.
Make sure all preparation steps are completed.
**DO NOT INSTALL IF DAMAGED**
b.
Determine your ceiling height to see if you need an extension.
**RETURN OR EXCHANGE WILL BE DENIED IF INSTALLED**
a.
Be sure you have all the content of your purchase and required tools for
this installation.
b.
Installation may take at least 1 to 2 hours from start to finish.
c.
Plan to use as few elbows or turns as possible for more efficient air flow.
d.
Collar size may need to be increased if utilizing a long duct run.
e.
At least 12” of vertical duct is required before any turn.
f.
Do not try to install this unit by yourself, SERIOUS INJURY MAY OCCUR.
g.
At least two people are needed for installation.
h.
Hiring a certified installer and electrician is recommended.
2. LOCATION
**THIS MODEL MAY NOT FIT ALL CEILING HEIGHTS**
a.
Determine the exact location where you want to install the range hood.
b.
Recommended installation height above cooktop 27”-33”.
c.
Range hood should be mounted at stated measurements to ensure
performance and lifespan of electrical components.
d.
Correctly measure the dimension needed to install the unit.
e.
Electrical outlet feed will be positioned at the top right base of the unit.
3. HOOD
a.
Inspect for signs of defect or damage. (ie. scratches, dents, loose seams,
etc.)
b.
Before mounting, power up the unit to make sure it is working properly.
c.
Remove the protective file on the aluminum filters.
Use Fig. 1a and 1b on page 5 for measurements
7
i.
Hood unit height = 12-1/4”
ii.
Duct cover height = 18-3/16” (lower) + 18-1/16” (upper)
iii.
Duct cover minimum height = 19-7/16”
iv.
Duct cover maximum height = 35-5/8”
v.
(OPTIONAL) Extension duct cover height = 46”
vi.
Minimum height (lower duct cover with extension only) = 46-5/8”
vii.
Maximum height (lower duct cover with extension only) = 63-5/8”
c.
Determine the location you want to install the range hood. (Fig. 2a)
d.
Prepare back wall frame with cross wood support.
e.
Mount the unit onto wall with mounting screws (not included)
f.
Adjust the duct cover mounting bracket to your desired height.
g.
Use a spirit level to ensure the balance of the hood is true.
h.
(OPTIONAL) Use the conversion collar for 7” ducting.
i.
Connect a 6” or 7” ducting to the collar of the hood.
j.
Connect the exhaust piping to the outlet of the unit. (Fig. 2b)
k.
Finish off by sealing the connection point with aluminum tape.
l.
Slide the duct cover into the unit and adjust its height. (Fig. 2c)
m. Secure it with the (6) duct cover screws provided. (Fig. 2d)
2. EXTENSION DUCT COVER INSTALLATION
a.
Replace the original upper duct cover piece with the extension.
b.
Determine the desired height to mount the duct cover.
c.
REPEAT “STEP F – M” from WALL MOUNT INSTALLATION section.
8
INSTALLATION
3. COLD WEATHER INSTALLATION (OPTIONAL)
a.
Check with your local building codes to see if a CFM reducer is an
acceptable alternative to make-up air.
b.
Remove the RA-60TBCFMR (CFM reducer) and inspect for any sign of
defect or damage. (ie. Cracks, broken flips)
c.
AFTER COMPLETING Step A – G of Section 1 WALL MOUNT
INSTALLATION
d.
Place the CFM reducer onto the outlet of the unit and seal the connection
point with aluminum tape. (Be sure it is secure with no opening or gaps)
e.
REPEAT “STEP F – M” from WALL MOUNT INSTALLATION section.
4. DUCTLESS INSTALLATION
a.
AFTER COMPLETING Step A – G of Section 1 WALL MOUNT
b.
Remove the RA-60TBDK (ductless kit) and inspect for any sign of defect
INSTALLATION
or damage. (ie. dents, broken inlet)
c.
Mount the ductless kit at the top of the ceiling using the screws provided.
d.
Make sure the duct cover vent opening aligns with the air diverter. (Fig.
2e)
e.
Connect a 6” or 7” ducting to the collar of the hood.
f.
Connect the exhaust pipe to the outlet of the unit. (Fig. 2b)
g.
Connect the exhaust pipe to the air diverter collar.
h.
REPEAT “STEP K – M” from WALL MOUNT INSTALLATION section.
Installation diagram available on next page
INSTALLATION DIAGRAM
INSTALLATION DIAGRAM
9
10 OPERATION & FEATURES
CLEANING & MAINTENANCE
OPERATION & FEATURES
CLEANING & MAINTENANCE
WARNING!!!
1. EASY ACCESS CONTROL SWITCH (from left to right)
a.
Button 1 – Power ON / OFF
b.
Button 2 – Low speed
c.
Button 3 – Medium speed
d.
Button 4 – High speed
e.
Button 5 – Lights ON/OFF
11
To prevent the possibility of a fire and explosion, do not use
flammable liquids or solvents to clean the unit or any of its parts.
Check to make sure all power sources are disconnected
before servicing or taking unit apart for cleaning.
2. BAFFLE FILTERS
Please thoroughly clean the unit weekly as stainless steel
a.
(2) 14-7/8” x 10-5/8” baffle filters (30” model only)
b.
(3) 14-7/8” x 10-5/8” baffle filters (36” / 42” model only)
c.
(4) 14-7/8” x 10-5/8” baffle filters (48” model only)
can rust under certain condition or by improper cleaning
1. RANGE HOOD
a.
3. CHARCOAL FILTERS
unit. Spray on wiping cloth or sponge and wipe in the direction of the grain
**DO NOT WASH CHARCOAL FILTERS! IT WILL DISSOLVE!!**
a.
Use household cleaner to remove grease or dirt from the outer shell of the
Insert the charcoal filters on each side of the motor on top of the white
protective grill as shown below. (Fig. 3a)
to avoid scratching the unit. (DO NOT SPRAY DIRECTLY ONTO UNIT)
b.
Clean the inner working of the unit periodically to avoid grease build-up.
c.
Do not open control switch panel while the hood is connected to power.
d.
Use stainless steel cleaner to bring back the luster of the unit.
2. BAFFLE FILTERS
Fig. 3a
b.
Fig. 3b
Rotate the charcoal filters in a counter-clockwise motion until you hear a
click. (Fig. 3b)
c.
Installation is complete after the charcoal filters are secured in place.
a.
Remove filters from unit and place in warm soapy water.
b.
Clean each filter regularly to maintain efficient suction power.
c.
Do not drop filters.
d.
Let it soak thoroughly and then clean it with a wiping cloth or sponge.
e.
Filters may also be cleaned using residential dishwasher.
PART LIST / REPLACEMENT 13
12 TROUBLESHOOTING
PART LIST / REPLACEMENT
TROUBLESHOOTING
WARNING!!!
Check to make sure all power sources are disconnected
before starting any troubleshooting. Safety gloves and glasses
should be worn when working on the unit. Serious injury or death
may occur if safety precautions are not followed.
RA-60TB Series
Light issue (All not
turning on)
New transformer/ driver replacement is required.
LED light issue
1. Check all wiring to and from the unit.
2. LED may require new fixture or transformer.
Light issue (One light
not turning on)
Replace defective fixture.
Speed indicator not
showing speed levels
Complete control switch replacement is required.
Burnt/melted control
switch
Complete control switch replacement is required.
Speed levels not
working correctly
1. Check all wiring to and from the unit.
2. Complete control switch replacement is required.
Unit lacking smoke
intake
1. Check ducting for foreign object.
2. Ensure the ducting is properly sealed.
3. Clean filters to increase airflow.
Unit showing no power
indication
Unit making humming
noise
1. Make sure the power source is working properly.
2. All wiring is connected.
Replace defective capacitor with new one.
#
Description
#
Description
1
Duct cover bracket
8
Control Bracket
2
Duct cover
9
LED transformer
3
Duct cover holder
10
Capacitor
4
Hood bracket
11
Squirrel cage motor
5
Hood body assembly
12
Oil collector
6
LED lights
13
Baffle filters
7
Switch
14
6” – 7” round collar
14 WARRANTY / CONTACT US
WARRANTY / CONTACT US
WARRANTY / CONTACT US 15
WHAT IS NOT COVERED BY MANUFACTURE WARRANTY
1.
Damages resulting from any of the following:
LIMITED WARRANTY
a.
Improper installation or maintenance
Windster Hoods Inc. warrants its product against defects in material or workmanship as
b.
Any repair, modification, alteration or adjustment not authorized by
follows:
the manufacturer or an authorized service dealer
c.
Misuse and/or accidents
Labor: For a period of one (1) year from the date of purchase, if the product is
d.
Incorrect electric current, voltage or power supply
determined to be defective, Windster will attempt to repair the product, at its option, at
e.
Improper setting of any control (Pressing multiple selections at the
no charge. After the warranty period, customer must pay for all labor charges. During
same time)
the "labor" warranty period there will be no charge for any work done on the purchased
f.
Improper chemical cleaning (commercial or industrial cleaning agents)
model. (All labor repairs are limited only to the installation of electrical components.)
2.
Parts: In addition, Windster will supply, at no charge, new or rebuilt replacements in
Products purchased for use in a commercial or industrial setting (such as in a
hotel, office, restaurant, or other business)
exchange for defective parts for a period of two (2) years. After the warranty period, you
3.
must pay for all parts costs. During the "parts" warranty period, there will be no charge
4.
Aluminum Filters, Baffle Filters, Charcoal Filters, and Oil Cup Filters
for parts
5.
Light Bulbs
You must provide the serial number of your unit for any replacement parts during the
Damage resulting from natural disasters (earthquake, flood, storm, etc.)
CONTACT US
warranty period. This warranty applies to products purchased and serviced in the
United States only.
For products purchased in Canada, please contact your local retailer where you
purchased the unit for service.
* Windster Hoods, Inc. will attempt to repair malfunctioning units prior to shipping a
replacement. In the case that a unit cannot be repaired and must be replaced, Windster
Hoods, Inc. will not be held liable for removal/installation fees of the malfunctioning /
replacement unit.
Windster Hoods, Inc.
15210 Nelson Ave.
City of Industry, CA 91744
TEL: (626) 330-5800
FAX: (626) 330-5811
Toll Free: (877) 350 – 5215
E-mail: support@windsterhood.com
© Windster Hoods, Inc.
Information subject to change without notice
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising