XO XOE30W Manual

XO XOE30W Manual
XOE30
XOE36
READ AND SAVE THE INSTRUCTIONS
FOR RESIDENTIAL COOKING ONLY
Register your product online at: www.xoventilation.com
NEED HELP?
Call our ventilation experts at 800-966-8300
Dear Customer,
If you follow the recommendations contained in this Instruction Manual, our appliance
will give you constant high performance and will remain efficient for many years to
come.
1
1
CONTENTS
WARNING & CAUTION
CHARACTERISTICS
INSTALLATION & USE
MAINTENANCE & CLEAN
P r o d u ct S p eci f i ca t i o n & T ech n i ca l P a r a m et er s
Rated Voltage
120V
Rated Power Frequency
60Hz
Light Power
2x50W Halogen bulbs
Motor Power
150W
Total Power
250W
Motor
1
Parameters of Ducting Outlets
Options
- 6" Round Vertical Duct
- 3 1/4" x 10" Rectangle Vertical Duct
- 3 1/4 x 10" Rectangle Horizontal Duct
Ampere
2.08 Amps
Mounting height
26” to 32” from cooking surface
X O How B eautiful K itc hens B reath
1
2
WARNING
TO RUDUCE THE RICK OF FIRE, ELECTRIC SHOCK OR INJURE TO PERSONS,
PLEASE OBSERVE THE FOLLOWINGS:
length)
1. Installation work and electric wiring (including switch location) must be done by the
qualified person(s) in accordance with local applicable codes and standards, including firerated construction.
2. This hood may have sharp edges. Be careful to avoid cuts and abrasions during installation
and cleaning.
3. The hood must be placed at a minimum distance of 26” and a maximum of 32” from the
cooktop for best capture of cooking impurities and a minimum distance of 28” from gas
range.
4. Provide sufficient air for proper combustion and exhausting of gases through the chimney
of the burning equipment to prevent back drafting. Follow the heating equipment
manufacturer’s guideline and safety standards such as those published by the National Fire
Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air
Conditioning Engineer (ASHRAE), and the local code authorities.
5. Ducted fans must always be vented to the outdoors.
6. This appliance is design to be operated by adults. Children should not be allowed to temper
with the controls or play with this appliance.
7. To reduce the risk of fire or electric shock, do not use this fan with any solid-state speed
control device.
round
8. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other
hidden utilities.
9. Before servicing or cleaning unit, switch power off at service panel and lock the service
disconnecting means to prevent power from being switched on accidentally. When the
service disconnecting means cannot be locked, securely fasten a prominent warning device,
such as a tag, to the service panel.
10.Use this unit only in the manner intended by manufacturer. If you have questions, please
contact the manufacturer or local agent.
11.This unit must be grounded.
WARNING-TO REDUCE THE RISK OF FIRE, USE ONLY THE METAL DUCTWORK.
and ASHRAE.
3
4
WARNING - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
1. Never leave surface units unattended at high settings. Boilovers cause smoking
and greasy spillovers that may ignite. Heat oils slowly on low or medium
settings.
2. Always turn hood ON when cooking at high heat or when cooking flaming
best capture of cooking impurities.
6. This hood is not intended to be used as a shelf.
7. Please read specification for further information and requirements.
NOTE: If hood is to be installed non-ducted, buy a set of (2) non-ducted filters from your
local retailer and attach them to the aluminum mesh filters.
foods (i.e. Crepes Suzette, Cherries Jubilee, and Peppercorn Beef Flambé).
3. Clean ventilating fans frequently. Grease should not be allowed to accumulate
CHARACTERISTICS
on fan or filter.
4. Use proper pan size. Always use cookware appropriate for the size of the
Dimension
surface element.
WARNING – TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF
1 2 .6 "
30 "/ 36
A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING:
"
1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn
5.68"
off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out
immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.
2. NEVER PICK UP A FLAMING PAN – You may be burned or spread the fire.
3. DO NOT USE WATER, including wet dishcloths or towels – violent steam
explosion will result.
21"
4. Use an extinguisher ONLY if:
INSTALLATION & USE
a. You know you have a Class ABC extinguisher and you already know how to
operate it.
b. The fire is small and contained in the area where it started.
c. The fire department is being called.
NOTE: on the stainless steel hoods, carefully remove the plastic protective film from exterior of
the surfaces of the hood prior to final installation.
Caution: To Reduce Risk of Fire and Electric Shock, install this range hood only with
integral blowers supplied by manufacturer.
d. You can fight the fire with your back to an exit.
Based on “Kitchen Fire Safety Tips” published by NFPA.
CAUTION
1. For indoor use only.
2. For general ventilating use only. Do not use to exhaust hazardous or explosive materials
and vapors.
3. To avoid motor bearing damage and noisy and/or unbalanced impeller, keep drywall spray,
construction dust, etc., off power unit.
4. Your hood motor has a thermal fuse which will automatically shut off the motor if it
becomes overheated.
5. The hood MUST NOT BE LESS than 26” and at a maximum of 32” above cooktop for
5
DESCRIPTION / CONNECTION
This appliance may be installed in ducted version or non-ducted version. Use proper
installation template, for replacement of ductwork and electrical cutout in cabinet or wall.
For a non-ducted version installation, do not cut a duct access hole.
DUCTED VERSION
The hood discharge kitchen air saturated with odor and fume passes it through the grease filters
and expels it to the outside through an outlet pipe. With this version the charcoal filters are not
required.
1. Determine whether the hood will discharge vertically (3 1/4″×10″ or 6” round) or horizontally
(3 1/4″×10″ only). For vertical or horizontal discharge, run ductwork between the hood
location and a roof cap or wall cap. For best results, use a minimum number of transitions and
elbows.
6
2. Remove the bottom cover fixed in place with 3 screws.
HOUSE WIRING
26"-32"
** Duct and roof cap/wall cap are not supplied.
3. Remove the Accessory parts box from inside of the hood.
Warning: to avoid the risk of fire, use only the metal ductwork.
NON-DUCTED VERSION
1.No need of plastic or metal duct.
HOUSE WIRING
4.Non-ducted installation only
Remove the Recirculation Plate out of the hood and use sealing plate (supplied in the
accessory box) to seal the outlet off.
26"-32"
2. Must be installed charcoal filter on the hood.
NOTE: Buy a set of (2) non-ducted filters from your local retailer and attach them
to the aluminum mesh filters.
PREPARATION OF THE HOOD BEFORE INSTALLATION
1. Remove the Aluminum filter from the hood.
5.Non-ducted installation only
Attach the charcoal filter to the aluminum filter back, locking well with metal wires.
7
8
2. Attach house power cable to hood using appropriate clamp.
3. Hold the hood in position under the cabinet. Tighten all 4 mounting screws completely to
secure the hood to the cabinet.
5.Ducted installation only
Tighten the Recirculation Plate and the outlet with screws.
4.For ducted installation, connect ductwork to hood and use duct tape to make joints
secure and air-tight. Make sure the damper/duct connector enters ductwork and that the
damper opens and closes freely.
5.Connect the house power cable to the range hood wiring: BLACK to BLACK, WHITE to WHITE
and GREEN or BEAR WIRE to GREEN GROUD SCREW.
6. Ducted installation only
6.1 Remove 3 1/4″×10″ vertical, 3 1/4″×10″ horizontal, or 6” round knockout
plates as appropriate for your ducting method.
6.2 Attach 3 1/4″×10″ Damper/Duct connector (if using 3 1/4″×10″duct) or 6”
Damper/Duct connector (if using 6” round duct) over the Knockout openings.
6.Reinstall the Bottom Cover to the hood.
INSTALLATION
WARNING: To reduce the risk of electrical shock, switch power off at service panel. Lock
or tag service panel to prevent power from being switched on accidentally.
1.Remove Electrical Wiring Box Cover from inside of hood and appropriate Electrical Power
Cable Knockout from top or back of hood.
9
10
7.Install the Halogen lamp.
* Grease filters are washable.
Remove the grease filters from the hood. Wash the filters, taking care not to bend them. Allow
them to be dry before refitting.
When refitting the filters, make sure that the handle is visible from the outside.
Reinstall the grease filters to the hood.
e
e clockwis
(2)Rotat
(1)Push
in
8.Replace the filters and turn on the power at service panel and test for proper operation.
OPERATION
The hood is operated using a rocker switch on the front panel.
Blower switch
The 3-position blower switch turns the blower ON/OFF and controls the blower speed.
Set the left side of the switch (0) turns blower on and off.
Set the middle of the switch (1) turns blower on to low speed.
Set the right side of the switch (2) turns blower to high speed.
Light switch
The 3-position blower switch turns the lights ON/OFF and controls their intensity.
Set the left side of the switch (0) turns the lights on and off.
Set the middle of the switch (1) turns the lights on to low intensity.
RECIRCULATION CHARCOAL FILTER (FILTERING VERSION)
This charcoal filter is not washable, can not be regenerated, and should be replaced
approximately every 3 months of operation, or more frequently in the case of heavy usage.
HOOD CLEANING
Stainless steel is one of the easiest materials to keep clean. Occasional care will help preserve
its fine appearance.
Cleaning tips:
* Hot water with soap or detergent is all that is usually needed.
* Follow all cleaning by rinsing with clear water. Wipe dry with a clean, soft cloth to avoid water
marks.
* For discolorations or deposits that persist, use a non-scratching household cleanser or
stainless steel polishing powder with a little water and a soft cloth.
* For stubborn cases use a plastic scouring pad or soft bristle brush together with cleanser and
water. Rub lightly in direction of polishing lines or “grain” of the stainless finish. Avoid using
too much pressure that may mar the surface.
* Do not allow deposits to remain for long periods of time.
* Do not use ordinary steel wool or steel brushes. Small bits of steel may adhere to the surface
causing rust.
* Do not allow salt solutions, disinfectants, bleaches, or cleaning compounds to remain in
contact with stainless steel for extended periods. Many of these compounds contain
chemicals that may be harmful. Rinse with water after exposure and wipe dry with a clean
cloth.
* Painted surfaces should be cleaned with warm water and mild detergent only.
Set the right of the switch (2) turns the lights on to high intensity.
CAUTION- The unit is for General Ventilating Use Only. Do Not Use To Exhaust Hazardous
Or Explosive Materials And Vapors
MAINTENTANCE & CLEAN
FILTER & REPLACEMENT PARTS
Light Bulb: Model: XOPXOE12B (GU10, 120V, 50W Max)
Recirculation Filters: Model: XORFK10 = 30”, Model: XORFK11=36”
Replacement Mesh Filters:
Model: XOPXOE3012F = 30”, Model: XOPXOE3612F=36”
Caution: Unplug or disconnect the appliance from the power supply before servicing.
GREASE FILTER
* The grease filters should be cleaned frequently (ever y two months of operation, or
more frequently for heavy use). Use a warm detergent solution.
11
12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement