XO XOMI36G Manual
XOMI36G
XOMI42G
NEED HELP?
Call our ventilation experts toll free al 800-966-8300
AVEZ-VOUS BESOIN D’AIDE ?
Contactez nos experts au numéro gratuit 800-966-8300
¿NECESITA AYUDA?
Póngase en contacto con nuestros expertos a través del número gratis 800-966-8300
USA RANGE HOOD - User instructions
F
HOTTE DE CUISINE - Notice d’utilisation
E
CAMPANA EXTRACTORA - Manual de utilización
XO Hood Warranty
Proof of original purchase date and invoice is needed to obtain
service under warranty.
What is covered
Limited 2 Year Warranty.
For 2 years from the original date of purchase, we will provide,
free of charge, parts and service labor in your home to repair or
replace any part of the hood that fails because of a manufacturing
defect.
The warranty is extended to the original purchaser for products
purchased for ordinary home use in North America.
Should you require service for your XO product call a product
service specialist at 800.966.8300
What is not covered
Improper Installation.
Service trips to the home to teach you how to use the product.
Resetting circuit breakers.
Damage caused after delivery.
EXPECT MORE FROM XO
When buying any XO appliance
you can be confident
you have purchased a high quality,
innovative, and stylish product,
from a company who cares about you
ENGLISH
USA
IMPORTANT SAFETY INSTRUCTIONS
FOR RESIDENTIAL USE ONLY
READ AND SAVE THESE INSTRUCTIONS
PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING.
IMPORTANT: Save these Instructions for the Local Electrical Inspectors use.
INSTALLER: Please leave these Instructions with this unit for the owner.
OWNER: Please retain these instructions for future reference.
Take care when using cleaning agents or detergents.
Suitable for use in household cooking area.
WARNING - To reduce the risk of fire or electric shock, do not use this fan with any
Solid-State Speed Control Device.
CAUTION - To reduce risk of fire and to properly exhaust air, be sure to duct air outside – Do not vent exhaust air into spaces within walls or ceilings or into attics, crawl
spaces, or garages.
CAUTION - For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.
CAUTION - To avoid motor bearing damage and noisy and/or unbalanced impellers,
keep drywall spray, construction dust, etc. off power unit.
CAUTION - Please read specification label on product for further information and
requirements.
WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
A. Use this unit only in the manner intended by the manufacturer. If you have questions,
contact the manufacturer.
B. Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally.
When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
WARNING - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
A. Never leave surface units unattended at high settings. Boilovers cause smoking and
greasy spillovers that may ignite. Heat oils slowly on low or medium settings.
B. Always turn hood ON when cooking at high heat or when flambeing foods (i.e.
-3-
Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambè).
C. Clean ventilating fans frequently. Grease should not be allowed to accumulate on
fan or filter.
D. Use proper pan size. Always use cookware appropriate for the size of the surface
element.
E. Keep fan, filters and grease laden surface clean.
F. Use high range setting on range only when necessary.Heat oil slowly on low to medium setting.
G. Don’ t leave range unattended when cooking.
H. Always use cookware and utensils appropriate for the type and amount off food being prepared.
WARNING – TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE
TOP GREASE FIRE, OBSERVE THE FOLLOWINGa:
A. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off
the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately,
EVACUATE AND CALL THE FIRE DEPARTMENT.
B. NEVER PICK UP A FLAMING PAN – You may be burned.
C. DO NOT USE WATER, including wet dishcloths or towels – a violent steam explosion
will result.
D. Use an extinguisher ONLY if:
1. You know you have a Class ABC extinguisher, and you already know how to operate
it.
2. The fire is small and contained in the area where it started.
3. The fire department is being called.
4. You can fight the fire with your back to an exit.
aBased on “kitchen firesafety tips” published by NFPA.
Proper maintenance of the Range Hood will assure proper performance of the
unit.
INSTALLATION INSTRUCTIONS
WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
A. Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction.
B. Sufficient air is needed for proper combustion and exhausting of gases through the
flue (chimney) of fuel burning equipment to prevent back drafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society
for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local
code authorities.
C. When cutting or drilling into wall or ceiling, do not damage electrical wiring and
other hidden utilities.
-4-
D. Ducted fans must always be vented to the outdoors.
E. This unit must be grounded.
WARNING - TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.
WARNING - UNDER CERTAIN CIRCUMSTANCES DOMESTIC APPLIANCES MAY BE
DANGEROUS.
A. Do not check filters with hood working.
B. Do not touch the lamps after a prolonged use of the appliance.
C. No food must be cooked flambè underneath the hood.
D. The use of an unprotected flame is dangerous for the filters and could cause fires.
E. Watch constantly the fried food in order to avoid the cooking oil flares up.
F. Before performing any mainteinance operation, disconnect the hood from the
electrical service.
The manufacturers will not to accept any responsability for eventual damages,
because of failure to observe the above instructions.
-5-
Installation Preparation
DUCT FITTINGS:
This Hood Must Use an
6" Round Duct. It Can
Transition to 3-1/4" x
10" or 3-1/4" x 12" Duct.
Use this chart to compute maximum permissible
lengths for duct runs to
outdoors.
NOTE: Do not exceed maximum permissible equivalent
lengths!
Maximum duct length:
100 feet for range hoods.
Flexible ducting:
If flexible metal ducting
is used, all the equivalent
feet values in the table
should be doubled. The
flexible metal duct should
be straight and smooth
and extended as much as
possible.
DO NOT use flexible plastic
ducting.
NOTE: Any home ventilation
system, such as a ventilation
hood, may interrupt the
proper flow of combustion
air and exhaust required
by fireplaces, gas furnaces,
gas water heaters and other
naturally vented systems. To
minimize the chance of interruption of such naturally
vented systems, follow the
heating equipment manufacturer’s guidelines and
safety standards such as
those published by NFPA.
Duct
Piece:
Equivalent
Dimensions: Number
Length*:
Quantity
Used:
Total
Equivalent
Length:
ft. (per foot
Round, straight 1
lenhgth)
3-1/4" x 10"
straight
1 ft. (per foot
lenhgth)
90° elbow
12 ft.
45° elbow
7 ft.
3-1/4" x 10"
3-1/4" x 12"
90° elbow
14 ft.
10 ft.
3-1/4" x 10"
3-1/4" x 12"
45° elbow
8 ft.
6 ft.
3-1/4" x 10"
3-1/4" x 12"
90° elbow
33 ft.
24 ft.
6" round to
rectangular
2 ft.
Rectangular to
8" round
2 ft.
3-1/4" x 10"
3-1/4" x 12"
6" round to
rectangular
transition 90°
elbow
4 ft.
4 ft.
3-1/4" x 10"
3-1/4" x 12"
Rectangular to
6" transition
90° elbow
4 ft.
4 ft.
Round wall
cap with
dramper
24 ft.
3-1/4" x 10"
3-1/4" x 12"
Rectangular
wall cap with
dramper
24 ft.
18 ft.
Round roof
cap
33 ft.
*Actual length of straight duct plus duct
fitting equivalent. Equivalent length of duct Total Duct Run =
pieces reflect requirements for good venting
performance with any ventilation hood.
-6-
NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces,
ceiling, attics or garages.
All exhaust must be ducted to the outside, unless using the recirculating option.
Use single wall rigid Metal ductwork only.
Fasten all connections with sheet metal screws and tape all joints w/ certified Silver
Tape or Duct Tape.
INSTALL THE DUCTWORK:
NOTE: To reduce the risk of fire, use only metal ductwork.
1.
2.
3.
4.
Decide where the ductwork will run between the hood and the outside.
A straight, short duct run will allow the hood to perform most efficiently.
Long duct runs, elbows, and transitions will reduce the performance of the
hood. Use as few of them as possible.
Install a roof or wall cap. Connect 6” round metal ductwork to cap and work
back towards hood location. Use duct tape to seal the joints between ductwork
sections.
-7-
Installation - Ducting Options
WARNING FIRE HAZARD
› Front of hood
› Side of hood
��������
�������
��������
��������������������������
��������������������
���������
› Top of hood
› Mounting height
and clearance:
�������
Hood Specifications
Product dimensions and clearance
XOMI36G - XOMI42G:
�����������������
���������
���
-8-
Installation Instructions
Installation - Vented to the outside
1. Installation:
Remove the structure from the packaging and remove the 2 screws A to separatethe upper part from the lower part
(Fig.1).
- Position hole template on the ceiling
paying attention that the arrow is positioned on the same side as the appliance
controls (Fig.2).
Make 4, Ø8 holes in the ceiling and drive
in 3 screws without completely tightening them. Pay attention not to insert
the screw into the hole marked with an
X on the hole template (the screws and
expansion plugs must be suitable for the
type of wall).
- Take the upper part of the structure B
(Fig.3) and insert the 3 slots onto the 3
screws that are not completely tightened. Rotate slightly to fit (Fig.3). Drive in
the fourth screw X and tighten the remaining 3 to allow definitive blocking of the
upper part ofstructure B.
- Take the lower part of the telescopic
structure C and insert it into the upper
�
�
Fig.1
�
�
Fig.2
�
�
Fig.3
-9-
structure B (Fig.4).
Adjust the height by referring to the
amounts indicated in (Fig.5) and block
it usingthe 8 screws G that are supplied
(Fig.6).
- Fix the flexible pipe to the prepared air
evacuation hole (Fig.7).
- Take the upper chimney piece and fix
it to the structure using the 2 screws A
(Fig.8). Join the lower chimney piece
with the upper one and fix it carefully
using adhesive tape L (Fig.9A).
- Unscrew the 2 screws O, max 3 mm
(Fig.9A). Insert the exhaust unit inside
�
�
Fig.4
�
�
�
�������
�
�
��������
�
�
�
������������������������������
�
Fig.5
Fig.6
- 10 -
�
Fig.7
Fig.8
�
�
�
�
�
�
�
��������
�
�
�
Fig.9
- 11 -
the structure paying attention that the
previously unscrewed screws O, hook
into the slots in the lower part as indicated in (Fig.9B). Drive in the 3 screws
N (supplied)and tighten the 2 screws O
(Fig.9B).
- Fix the air evacuation pipe H (not
supplied) onto the connection flange F
(Fig.10).
- Remove adhesive tape L and rest the
lower chimney piece above the cooker
hood (Fig.11).
- If the cooker hood is supplied with a
lower chimney piece that must be fixed
�
�
Fig.10
�
�
Fig.12
Fig.11
Fig.13
- 12 -
to the hood body with screws, remove the anti-grease filters from the hood by acting on
the relevant handles (Fig.13). Then screw the lower chimney piece pipe to the inside of
the hood, using screws P (Fig.12). Relocate the filters in their seat.
IMPORTANT - The range hood must be secured to wall studs or use drywall anchors
capable of supporting 75 lbs.
- 13 -
POWER SUPPLY:
IMPORTANT – (Please read carefully)
WARNING:
FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED.
Remove house fuse or open circuit breaker before beginning installation. Do not use an
extension cord or adapter plug with this appliance. Follow National electrical codes or
prevailing local codes and ordinances.
Electrical supply:
These vent hoods must be supplied with 120V, 60Hz, and connected to an individual,
properly grounded branch circuit, and protected by a 15 or 20 amp circuit breaker or
time delay fuse.
• Wiring must be 2 wire with ground.
• If the electrical supply does not meet the above requirements, call a licensed
electrician before proceeding.
• Route house wiring as close to the installation location as possible, in the ceiling or
back wall. Refer to Wiring Locations on page 15.
• Connect the hood wiring to the house wiring in accordance with local codes.
WARNING: The improper connection of the equipment-grounding conductor
can result in a risk of electric shock. Check with a qualified electrician or service representative if you are in doubt whether the appliance is properly grounded.
- 14 -
2. CONNECT ELECTRICAL:
WARNING - TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: Before making electrical connections to power
supply, the electrical box must be secured in place as indicated in Fig.14.
Before installing the appliance fix the electrical box as indicated in Fig.14.
�
�
Fig.14A: Lift the electrical plant box.
Fig.14B: Remove the 3 fixed screws.
�
Fig.14C: Position the electrical box so it is in the line with the holes of the previously
removed screws and tighten.
- 15 -
• Power Supply Connection:
For connection to the power supply refer to the following Fig.15:
1. Remove the power supply cover by undoing the (2) screws (Fig.15A).
2. Break through the hole on the box cover.
3. Secure the power supply conduit to the cover.
4. Connect the wires of the hood to those of the power supply as described
Fig.15B:
BLACK = L line
WHITE = N neutral
GREEN/YELLOW = G ground
- A double-pole switch properly rated must be installed to provide the range hood
power supply disconnection.
- Connect the electrical conduit to the Field Wiring Compartment using listed conduit
fittings.
�
�
Fig.15
- 16 -
- Carry out the power supplly connection in accordance with the national electric
code, ANSI/NFPA 70-1999.
5. Insert the wires into the box, then close the box cover, securing it using the screws
that were previously removed.
The appliance must be installed at a minimum height of 27" from an electric cooker
stove, or 32" from gas or combined cooker
stoves. If a connection ductwork composed
of two parts is used, the upper part must
be placed outside the lower part. Do not
connect the range hood exhaust duct air
to the same duct air used to exhaust hot
air or fumes from other appliances other
than electrical. Before proceeding with
the assembly operations, remove the antigrease filter(s) (Fig.16) so that the unit is
easier to handle.
Fig.16
3. Connect the Ductwork:
�����������������
���
- 17 -
Ductless Recirculating Option:
�
�
�
Carbon filter kit XORFK01: The kit includes an air diverter A, 1 screw B and 2 rectangular filters C.
���
�
���
�
�
Fig.1: Put together the two parts of the air deviator as shown in picture no 3.1. It may be necessary to cut the deviator to fit the width of the
chimney as shown in picture 3.2. A sharp blade
or Hacksaw is recommended to trim the plastic.
- 18 -
�
Fig.2: To remove the two screws
E, to take down the lower chimeny F.
�
�
�
�
�
�
�
6" Round Flexible
Metal Duct Pipe Not
Included
Fig.3: To fix the air diverter A on the support’s
bracket using the screw B as it is shown in
the figure. Once that the air diverter A has
been fixed, it is necessary to connect the
flexible pipe (6" Round Flexible Metal
Duct Pipe Not Included).
Fig.4: To take the upper chimeny F
and to fix it to the structure using the
two screws E.
�
�
�
�
6" Round
Flexible
Metal
Duct Pipe
Not
Included
Fig.5: To join the lower chimney 1 with the
upper one and to fix it carefully with the
adhesive tape 2. To fix the flexible pipe (6"
Round Flexible Metal Duct Pipe Not
Included) on the flange of connection 3.
- 19 -
Fig.6: Remove adhesive tape 2 and
rest the lower chimney piece above
the cooker hood.
�
�
�
�
Fig.7: Remove the aluminum panels
by pulling the lever 1 out and pushing
downwards 2.
Fig.8: The charcoal filters C must be fitted in the ducting unit located inside the
hood.
�
�
�
�
Fig.9: Put the aluminum panels back in
place (Fig.7).
- 20 -
USE
• If the apparatus is equipped with the
following controls luminous:
A = LIGHT
B = OFF
C = SPEED I
D = SPEED II
E = SPEED III
F = AUTOMATIC STOP TIMER - 15 minutes
(*)
�
�
�
�
�
�
• If your appliance does not have the
INTENSIVE speed function, press key E
for two seconds and it will be activated for
10 minutes after which it will return to the
previously set speed. When the function
is active the LED flashes. To interrupt it
before the 10 minutes have expired press
key E again.
• By pressing key F for two seconds (with the hood switched off ) the “clean air” function
is activated. This function switches the appliance on for ten minutes every hour at the first
speed. As soon as this function is activated the motor starts up at the first speed for ten
minutes, During this time key F and key C must flash at the same time. After ten minutes
the motor switches off and the LED of key F remains switched on with a fixed light until
the motor starts up again at the first speed after fifty minutes and keys F and C start to
flash again for ten minutes and so on. By pressing any key for the exclusion of the hood
light the hood will return immediately to its normal functioning (e.g. if key D is pressed
the “clean air” function is deactivated and the motor moves to the 2nd speed straight
away. By pressing key B the function is deactivated).
(*) The “automatic stop timer” delays stopping of the hood, which will continue functioning for 15 minutes at the operating speed set at the time this function is activated.
• Active carbon/grease filter saturation:
- When button A flashes at a frequency of 2 seconds, the grease filters must be
cleaned.
- When button A flashes at a frequency of 0.5 seconds, the carbon filters must be
replaced.
After the clean filter has been replaced, the electronic memory must be reset by pressing
button A for approximately 5 seconds, until the light on the button stops flashing.
- 21 -
MAINTENANCE
• We recommend that the cooker hood
is switched on before any food is cooked.
We also recommend that the appliance
is left running for 15 minutes after the
food is cooked, in order to thoroughly
eliminate all contaminated air. The effective performance of the cooker hood
depends on constant maintenance; the
anti-grease filter and the active carbon
filter both require special attention.
• The anti-grease filter is used to trap
any grease particles suspended in the air,
therefore is subject to saturation (the time
it takes for the filter to become saturated
depends on the way in which the appliance is used). The grease filters should be
cleaned frequently. Use a warm detergent
solution. Grease filters are a dishwasher safe.
- To prevent potential fire hazards, the anti-grease filters should be washed a minimum
of every 2 months (it is possible to use the dishwasher for this task).
- After a few washes, the colour of the filters may change. This does not mean they have
to be replaced. If the replacement and washing instructions are not followed, the antigrease filters may present a fire hazard.
• The active carbon filters are used to purify the air which is released back into the room.
The filters are not washable or re-usable and must be replaced at least once every four
months. The active carbon filter saturation level depends on the frequency with which
the appliance is used, the type of cooking performed and the regularity with which the
anti-grease filters are cleaned.
• Clean the cooker hood frequently, both inside and outside, using a cloth which has
been dampened with denatured alcohol or neutral, non-abrasive liquid detergents.
• The light on the cooker hood is designed for use during cooking and not for general
room illumination. Extended use of the light reduces the average duration of the bulb.
• Hood Cleaning:
Stainless steel is one of the easiest materilas to keep clean. Occasional care will help
preserve its fine appearance.
Cleaning tips:
- Hot water with soap or detergent is all that is usually needed.
- Follow all cleaningby rising with clear water. Wipe dry with a clean, soft cloth to avoid
water marks.
- For discolorations or deposit that persist, use a non-scratching household cleanser or
stainless steel polishing powder with a little water and a soft cloth.
- For stubborn cases, use a plastic scouring pad or soft bristle brush together with cleaser
and water. Rub lightly in direction of polishing lines or “grain” of the stainless finish. Avoid
using too much pressure wich may mar the surface.
- 22 -
- DO NOT allow deposit to remain for long periods of time.
- DO NOT use ordinary steel wool or steel brushes. Small bits of steel may adhere to the
surface causing rust.
- DO NOT allow salt solutions, disinfectants, bleaches, or cleaning compounds to remain
in contact with stainless steel for extended periods. Many of these compounds contain
chemicals with may be harmful. Rinse with water after exposure and wipe dry with a clean
cloth.
Painted surfaces should be cleaned with warm water and mild detergent only.
- 23 -
FUSE
• The halogen lamps circuit is controlled
by a fuse 5x20 mm, 125V 5A. In case of
necessity it can be replaced only by specialized personnel.
• Replacing halogen light bulbs:
To replace the halogen light bulbs B,
remove the glass panel C using a lever
action on the relevant cracks.
Replace the bulbs with new ones of the
same type.
Caution: do not touch the light bulb with
bare hands.
�
�
- 24 -
XOMI36G - XOMI42G:
���
��
���
��
���
��
���
���
���
��
���
���
���
���
���
��
���
��
��
���
- 25 -
���
OPTIONS AND ACCESSORIES:
Model XORFK01 - Ductless Recirculating Filter Kit.
Model XOEDCMI - Duct Cover Extension.
This accessory is available for installation with ceiling heights above 9 ft to 10 ft.
- 26 -
INSTALLATION PREPARATION:
Check installation hardware:
Locate the hardware package packed with the hood and check contents.
TYPE
DESCRIPTION
N°
A
1/8" x 6/16"
12
B
3/16" x 5/16"
9
Aluminum filters
2-piece decorative duct cover
(dimension shown for reference only)
���
���
���
��������
���������
�
���
����
- 27 -
XOMI Spec Sheet
Model: XOMI36G - XOMI42G
Sizes: 36"- 42" Depth: 23-5/8"
Features and Benefits:
- 600 CFM high velocity blower optimally removes
Smoke, Grease and Odors.
- 3+1 speed electronic illuminated controls.
- Four 20W Halogen Lights - Provide brilliant
illumination over the cooking surface.
- High quality Stainless Steel with incomparable
handcrafted Italian finish.
- Aluminum Mesh Filters - Trap airborne smoke and
grease particles. They can be easily be removed for
dishwasher-safe cleaning.
- Standard Chimney fits ceilings up to 9 ft tall, optional
chimney extension for ceilings up to 10 ft.
- Mounting Height from cooking surface 27"-32".
Duct Options and Electrical Requirements:
- 6 inch duct required.
- Ductless Option for applications where no ducting
in available.
- AC 120v-60Hz (4.18amp).
Options:
- Optional duct cover extension is available for ceiling
heights up to 10 ft tall.
Model: XOEDCMI
- Optional recirculating kit if outside venting is
available.
Model: XORFK01
XO is Exclusively Distributed by:
Eastern Marketing Corp 24 Eisenhower Parkway Roseland,
New Jersey 07068 800-966-8300
www.easternmarketingcorp.com
www.xoappliace.com
- 28 -
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising