Jenn-Air | JGC3215GS | Dimension Guide | Jenn-Air JGC3215GS Dimension Guide

JENN-AIR DETAILED PLANNING DIMENSIONS
®
1 of 2
15" 2-BURNER MODULAR GAS COOKTOP
JGC3215G – 15" x 45⁄32" x 21"
PRODUCT DIMENSIONS
MODEL #
A
A
A
B
B
in
cm
A
Overall width
15
38.1
B
Overall depth
21
53.3
C
Center of cooktop to center of gas inlet
21
4 ⁄32
11.8
14 ⁄64
36.3
1
D* Width of cooktop base
B
JGC3215G
19
E
Height of cooktop base
3 ⁄4
8.3
F
Height from gas inlet to underside
of cooktop
45⁄32
10.6
G
Height of cooktop with grates
11⁄4
3.2
H
Depth of cooktop base
20 ⁄64
51.6
19
*Measured from tab to tab. Tabs should not be bent during installation.
TOP VIEW
G
E
E
F
G
F
E
C
C
D*
D*
G
F
C
D*
FRONT VIEW
B
B
B
H
H
H
SIDE VIEW
IMPORTANT: Dimensional specifications are provided for planning purposes only.
Do not make any cutouts based on this information. Refer to the Installation Guide before
selecting cabinetry, verifying electrical/gas connections, making cutouts or beginning installation.
All Jenn-Air® appliances are appropriately UL, CUL or CSA approved.
8995AdZw217
JENN-AIR DETAILED PLANNING DIMENSIONS
®
2 of 2
15" 2-BURNER MODULAR GAS COOKTOP
JGC3215G – 15" x 45⁄32" x 21"
OPENING/CLEARANCE DIMENSIONS
MODEL #
JGC3215G
in
cm
Width of combustible area above
cooking surface (min.)
Width from cooktop to fixed wall
B
or other combustible material (min.)
Side
Width to outer
edge of electrical outlet
C
Cabinet
(recommended)
Width to gas supply line location
D
I
(recommended)
Height to bottom
J of uncovered wood or
E*
metal cabinet above cooking surface (min.)
Height to bottom of uncovered wood
F
or metal cabinet (min.)
Height to top edge of electrical outlet
G
(min.)
Height to gas supply line location
H
(recommended)
Depth of upper cabinet (recommended)
I
J Depth from cutout to wall (min.)
K Width of cutout (recommended)
L Depth of cutout (recommended)
M Depth from cutout to front of countertop
e Recommended electrical access location
g Recommended gas supply line location
15
38.1
6
15.2
9
22.9
12
30.5
30
76.2
18
45.7
18
45.7
18
45.7
13
25⁄16
143⁄8
203⁄8
25⁄16
33.0
5.9
36.5
51.8
5.9
A
A
E*
F
B
B
G
H
e
C
g
D
FRONT VIEW
*Dimension can be reduced by 6" (15.2 cm) when bottom of wood or metal
cabinet is covered by not less than 1⁄4" (0.6 cm) flame retardant millboard
covered with not less than No. 28 MSG sheet metal, 0.015" (0.4 mm)
stainless steel, 0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper.
If installing a hood or microwave hood combination above the cooktop,
A
follow the hood or microwave hood combination instructions for
dimensional clearances above the cooking surface.
Side
Cabinet
GAS REQUIREMENTS
I
J
K
J
LOCATION REQUIREMENTS
M
TOP VIEW – CUTOUT
ELECTRICAL REQUIREMENTS
F
B
G
H
120 volt, 60 Hz, AC only, 15-amp fused, electrical circuit is required.
e
A time-delay fuse or dedicated circuit is recommended.
L
SIDE VIEW
E*
Natural Gas
This cooktop is factory-set for use with natural gas.
LP Gas Conversion
B
Conversion must be done by a qualified service technician. To convert to
LP gas, use an LP gas conversion kit.
g
C
• T o ensure cooktop base clearance, cabinet side walls need to be wider
than the cutout
D
• If cabinet has a drawer, allow a 4" (10.2 cm) minimum clearance
between countertop and top of drawer. Drawer depth may need to be
shortened to avoid interfering with the regulator.
IMPORTANT: Dimensional specifications are provided for planning purposes only.
Do not make any cutouts based on this information. Refer to the Installation Guide before
selecting cabinetry, verifying electrical/gas connections, making cutouts or beginning installation.
All Jenn-Air® appliances are appropriately UL, CUL or CSA approved.
8995AdZw217
Download PDF

advertising