Jenn-Air | JGC7530BP | Dimension Guide | Jenn-Air JGC7530BP Dimension Guide

Jenn-Air JGC7530BP Dimension Guide
JENN-AIR DETAILED PLANNING DIMENSIONS
®
1 of 2
30" GAS COOKTOP
JGC7530B – 30" x 51⁄4" x 21"
A
PRODUCT DIMENSIONS
A
A
MODEL #
B
B
B
TOP VIEW
JGC7530B
in
cm
A
Overall width
30
76.2
B
Overall depth
21
53.3
C
Center of cooktop to center of gas inlet
12
30.5
D
Width of recessed cooktop
29 ⁄4
74.3
E
Height of recessed cooktop
1
3 ⁄4
8.3
1
1
F
Height from gas inlet to countertop
5 ⁄4
13.3
G
Height with grates
11⁄4
3.2
H
Depth of recessed cooktop
20 ⁄4
51.4
1
G
E
E
E
G
C
D
D
D
C
C
F
FG
F
FRONT VIEW
B
B
H
SIDE VIEW
H
B
H
IMPORTANT: Dimensional specifications are provided for planning purposes only.
Do not make any cutouts based on this information. Refer to the Installation Guide before
selecting cabinetry, verifying electrical/gas connections, making cutouts or beginning installation.
All Jenn-Air® appliances are appropriately UL, CUL or CSA approved.
8658CdZw1015
JENN-AIR DETAILED PLANNING DIMENSIONS
®
2 of 2
30" GAS COOKTOP
JGC7530B – 30" x 51⁄4" x 21"
OPENING/CLEARANCE DIMENSIONS
MODEL #
JGC7530B
in
cm
Width of combustible area above
cooking surface (min.)
Width from cooktop to fixed wall
B
Side
or other combustible
material (min.)
Cabinet
C Width to outer edge of outlet (max.)
Height to bottom of uncovered wood or
D*
metal cabinet
G above cooking surface (min.)
Height to bottom of uncovered wood
E
or metal cabinetH(min.)
F Height to top edge of outlet (min.)
G Depth of upper cabinet (recommended)
H Depth from cutout to wall (min.)
Width of cutout
I
J Depth of cutout
K Depth from cutout to front of countertop
e Recommended electrical access location
g Recommended gas supply line location
A
A
D*
E
B
B
F
e
C
30
76.2
6
15.2
24
61.0
30
76.2
18
45.7
51⁄2
13
25⁄16
293⁄8
203⁄8
25⁄16
14.0
33.0
5.9
74.6
51.8
5.9
*Dimension can be reduced by 6" (15.2 cm) when bottom of wood or metal
cabinet is covered by not less than 1⁄4" (0.6 cm) flame retardant millboard
covered with not less than No. 28 MSG sheet metal, 0.015" (0.4 mm)
stainless steel, 0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper.
If installing a hood or microwave hood combination above the cooktop,
follow the hood or microwave hood combination instructions for
dimensional clearances above the cooking surface.
FRONT VIEW
GAS REQUIREMENTS
Natural Gas
This cooktop is factory-set for use with natural gas.
LP Gas Conversion
A
Conversion must be done by a qualified service technician. To convert to
LP gas, use an LP gas conversion kit.
Side
Cabinet
ELECTRICAL REQUIREMENTS
D*
120 volt, 60 Hz, AC only, 15-amp fused, electrical circuit is required.
A time-delay fuse or dedicated circuit is recommended.
G
LOCATION REQUIREMENTS
H
I
H
J
E
B
B
• T o ensure cooktop base clearance, cabinet side walls need to be wider
than the cutout.
F
• If cabinet has a drawer, allow a 4" (10.2 cm) minimum clearance
between countertop and top of drawer. Drawer depth may need to be
e
shortened to avoid interfering with the regulator.
C
K
SIDE VIEW
TOP VIEW – CUTOUT
IMPORTANT: Dimensional specifications are provided for planning purposes only.
Do not make any cutouts based on this information. Refer to the Installation Guide before
selecting cabinetry, verifying electrical/gas connections, making cutouts or beginning installation.
All Jenn-Air® appliances are appropriately UL, CUL or CSA approved.
8658CdZw1015
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising