Jenn-Air | JGC2530EB | JGC2530EB Dimensions Guide | Jenn-Air JGC2530EB JGC2530EB Dimensions Guide

JENN-AIR DETAILED PLANNING DIMENSIONS
®
1 of 2
30" GAS COOKTOP
JGC2530EB – 30" x 43⁄16" x 21"
PRODUCT DIMENSIONS
A
A
A
MODEL #
B
B
B
TOP VIEW
JGC2530EB
in
cm
A
Overall width
30
76.2
B
Overall depth
21
53.3
C
Center of cooktop to center of gas inlet
12 ⁄16
31.3
D* Width of recessed cooktop
29 ⁄16
74.5
E
Height of recessed cooktop
3
3 ⁄16
8.1
F
Height from gas inlet to countertop
3
4 ⁄16
10.6
G
Height with grates
25⁄16
5.9
20 ⁄16
51.6
H* Depth of recessed cooktop
5
5
5
*Measured from tab to tab. Tabs should not be bent during installation.
G
E
E
E
F
G
C
D*
D*
C
C
F
G
F
D*
FRONT VIEW
B
B
B
H*
SIDE VIEW
H*
H*
IMPORTANT: Dimensional specifications are provided for planning purposes only.
Do not make any cutouts based on this information. Refer to the Installation Guide before
selecting cabinetry, verifying electrical/gas connections, making cutouts or beginning installation.
All Jenn-Air® appliances are appropriately UL, CUL or CSA approved.
8765BdZw416
JENN-AIR DETAILED PLANNING DIMENSIONS
®
2 of 2
30" GAS COOKTOP
JGC2530EB – 30" x 43⁄16" x 21"
OPENING/CLEARANCE DIMENSIONS
MODEL #
JGC2530EB
in
cm
Width of combustible area above
cooking surface (min.)
Width from cooktop to fixed wall
B
or other combustible material (min.)
Side
Width to outer
edge of electrical outlet
C
Cabinet
(recommended)
Width to gas supply line location
D
I
(recommended)
Height to bottom
J of uncovered wood or
E*
metal cabinet above cooking surface (min.)
Height to bottom of uncovered wood
F
or metal cabinet (min.)
Height to top edge of electrical outlet
G
(recommended)
Height to gas supply line location
H
(recommended)
Depth of upper cabinet (recommended)
I
J Depth from cutout to wall (min.)
K Width of cutout
L Depth of cutout
Depth from cutout to front of countertop
M
(recommended)
e Recommended electrical access location
g Recommended gas supply line location
30
76.2
6
15.2
9
22.9
12
30.5
30
76.2
18
45.7
9
22.9
18
45.7
13
25⁄16
293⁄8
203⁄8
33.0
5.9
74.6
51.8
25⁄16
5.9
A
A
E*
F
B
B
G
H
e
C
g
D
FRONT VIEW
*Dimension can be reduced by 6" (15.2 cm) when bottom of wood or metal
cabinet is covered by not less than 1⁄4" (0.6 cm) flame retardant millboard
covered with not less than No. 28 MSG sheet metal, 0.015" (0.4 mm)
stainless steel, 0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper.
A
If installing a hood or microwave hood combination above the cooktop,
follow the hood or microwave hood combination instructions for
dimensional clearances above the cooking surface.
Side
Cabinet
GAS REQUIREMENTS
I
J
K
J
Natural Gas
This cooktop is factory-set for use with natural gas.
B
LP Gas Conversion
Conversion must be done by a qualified service technician. To convert to
LP gas, use an LP gas conversion kit.
G
ELECTRICAL REQUIREMENTS
LOCATION REQUIREMENTS
M
TOP VIEW – CUTOUT
F
B
H
120 volt, 60 Hz, AC only, 15-amp fused, electrical circuit is required. e
A time-delay fuse or dedicated circuit is recommended.
L
SIDE VIEW
E*
g
C
• T o ensure cooktop base clearance, cabinet side walls need to be wider
D
than the cutout.
• If cabinet has a drawer, allow a 4" (10.2 cm) minimum clearance
between countertop and top of drawer. Drawer depth may need to be
shortened to avoid interfering with the gas connection or regulator.
IMPORTANT: Dimensional specifications are provided for planning purposes only.
Do not make any cutouts based on this information. Refer to the Installation Guide before
selecting cabinetry, verifying electrical/gas connections, making cutouts or beginning installation.
All Jenn-Air® appliances are appropriately UL, CUL or CSA approved.
8765BdZw416
Download PDF

advertising