INSTALLATION INSTRUCTIONS FOR DOWNDRAFT VENT Table of Contents COOKTOP SAFETY.........................................................................1 INSTALLATION REQUIREMENTS..................................................3 Tools and Parts..............................................................................3 Location Requirements.................................................................3 Electrical Requirements................................................................4 Venting Requirements...................................................................8 External Venting Dimensional Planning........................................9 INSTALLATION INSTRUCTIONS..................................................11 Mounting Bracket Installation.....................................................11 Install Foam Strips......................................................................11 Recirculation (Non-ducted) Installation.......................................11 Install Cooktop, Downdraft and Blower Motor Assembly..........12 Complete Installation..................................................................13 WIRE DIAGRAM............................................................................14 COOKTOP SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.” These words mean: DANGER WARNING You can be killed or seriously injured if you don't immediately follow instructions. You can be killed or seriously injured if you don't follow instructions. All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed. IMPORTANT: Save for local electrical inspector’s use. W11170792A IMPORTANT SAFETY INSTRUCTIONS READ AND SAVE THESE INSTRUCTIONS 2 INSTALLATION REQUIREMENTS Tools and Parts Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. ■■ ■■ Use the countertop opening dimensions that are given with these Installation Instructions. Given dimensions are minimum clearances and provide 0" (0 cm) clearance. The model/serial/rating label is located on the front face of the electrical junction box cover. Tools Needed ■■ Tape measure ■■ Marker or pencil ■■ Phillips screwdriver ■■ Pliers ■■ Flat-blade screwdriver ■■ Jigsaw ■■ Level ■■ Caulking ■■ Drill ■■ Aluminum duct tape Parts Supplied Check that all parts are included. ■■ Blower housing assembly with electronic box and intake assembly ■■ (4) Mounting brackets (front and rear mounting brackets) with screws ■■ Grease filter ■■ (2) Blower hold down brackets to secure blower to cabinet ■■ Round duct 2-piece telescoping (blower assembly) ■■ Foam strip ■■ (4) Sheet metal screws to secure transition to downdraft intake and one transition Parts Needed For vented installations: ■■ 6” (15.2 cm) round metal ducting ■■ Jenn-Air® wall cap: Jenn-Air® 6” (15.2 cm) round wall cap with damper ■■ (8) Round or pan head wood and sheet metal screws See the “Assistance or Service” section in your Use and Care manual to order. For non-vented installations: ■■ Recirculation Kit part number W10807915 (See the “Assistance or Service” section in your Use and Care manual to order.) a. Recirculation duct housing b. (4) Mounting screws c. (2) Charcoal filters d. Recirculation housing cover e. (2) Mounting screws – cover f. Duct extension g. (4) Mounting screws – duct extension For non-vented installations side recirculation only: ■■ 1-6” (15.2 cm) round 90 degree elbow and 1-6” (15.2 cm) round to 3Z\v” x 10” (8.3 cm x 25.4 cm) transition and 1- 3Z\v” x 10” (8.3 cm x 25.4 cm) elbow. ■■ Plywood Pedestal to raise blower mounting. See instruction detail for non-vented installation. Check local codes. Check existing electrical supply. See the “Electrical Requirements” section. It is recommended that all electrical connections be made by a licensed, qualified electrical installer. A A. Model/serial/rating label location Grounded electrical supply is required. See the “Electrical Requirements” section. ■■ If cabinet has drawers, drawers will need to be removed and drawer fronts installed on front of cabinet. NOTE: The exhaust system is for outside venting. For non-vented (recirculating) installation, see “For non-vented (recirculating) installations only” in the “Connect Vent System” section. Recirculating Kit part number W10807915 is available from your dealer or an authorized parts distributor. IMPORTANT: An undercounter built-in oven cannot be installed under this product. ■■ Electrical Connection Locations Center of Intake C A B Location Requirements IMPORTANT: Observe all governing codes and ordinances. When installing the downdraft, use the minimum dimensions given. A. 3 prong grounding type outlet with correct polarity B. 12” (30.5 cm) from centerline of downdraft intake C. 18” (45.7) minimum 3 Electrical Requirements WARNING If codes permit and a separate ground wire is used, it is recommended that a qualified electrical installer determine that the ground path is adequate. A copy of the above code standards can be obtained from: National Fire Protection Association 1 Batterymarch Park Quincy, MA 02169-7471 CSA International 8501 East Pleasant Valley Road Cleveland, OH 44131-5575 ■■ A 120-volt, 60 Hz., AC-only, 15-amp fused, electrical circuit is required. A time-delay fuse or circuit breaker is also recommended. It is recommended that a separate circuit serving only this downdraft vent be provided. ■■ Electronic touch pad systems operate within wide voltage limits, but proper grounding and polarity are necessary. Check that the outlet provides 120-volt power and is correctly grounded and polarized. Do not use an extension cord. ■■ Failure to follow these instructions can result in death, fire, or electrical shock. The wiring diagram is provided with this downdraft vent. See the “Wiring Diagram” section. ■■ Downdraft must have a dedicated electrical receptacle and power supply. Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. IMPORTANT: The downdraft vent must be electrically grounded in accordance with local codes and ordinances, or in the absence of local codes, with the National Electrical Code, ANSI/ NFPA 70 or Canadian Electrical Code, CSA C22.1. This downdraft is equipped with an electronic touch pad system that will not operate if plugged into an outlet that is not properly polarized. 4 Planning Your Cabinet Cutout Installation Options for Modular Downdraft Downdraft (DD) 1 2 15 min OFF 15" (38.1 cm) DD 15" (38.1 cm) (DD between cooktops) 15" (38.1 cm) cooktop (15" [38.1 cm]) 1 2 15 min OFF DD 15" (38.1 cm) (DD on outside of cooktop) 1 2 1 2 1 2 1 2 15 min OFF 15 min OFF 15 min OFF 15 min OFF 15" (38.1 cm) DD 15" (38.1 cm) DD DD 15" (38.1 cm) 15" (38.1 cm) 15" (38.1 cm) DD 1 2 1 2 1 2 1 2 15 min OFF 15 min OFF 15 min OFF 15 min OFF 15" (38.1 cm) DD 15" (38.1 cm) 15" (38.1 cm) DD 15" (38.1 cm) DD 30" (76.2 cm) OR 36" (91.4 cm) DD 1 2 1 2 1 2 1 2 15 min OFF 15 min OFF 15 min OFF 15 min OFF 15" (38.1 cm) DD 30" (76.2 cm) OR 36" (91.4 cm) DD 15" (38.1 cm) DD 30" (76.2 cm) OR 36" (91.4 cm) DD 15" (38.1 cm) Planning your counter cutout, refer to installation instruction for modular cooktops and full size cooktops and add: ■■ 355\64” (9.8 cm) for each downdraft mounted between cooktops 351\64” (9.6 cm) for each downdraft mounted on outside of cooktops The downdraft can be mounted between cooktops or on the sides of them. If mounted on the side, this requires relief cuts (back cutting) on the countertop. ■■ [3.1 cm] 114.7 1 13 ” 64 0 [2.2 cm] 7 8” [3.18 cm] 11 ” 4 [3.2 cm] 11 ” 4 [2.2 cm] 7 8” Figure A Figure B NOTE: When downdraft is mounted on outside of cooktop on right hand side, against the countertop, the countertop must be cut as shown in Figure A or Figure B. The shaded areas of the figures represent the countertop. 5 Product Dimensions Vent C A B A. 37/8” (9.8 cm) B. 21” (53.3 cm) C. 7/64” (2.9 mm) radius (4-corner radius) Blower Housing Assembly Right Side Front Side K A C L B D N E F M O G P Q S R H T J I A. B. C. D. E. F. G. H. I. J. 6 63/8" (16.2 cm) 11/2" (3.8 cm) 115/16" (4.9 cm) Ø 1/8" (3 mm) 87/8" (22.5 cm) 19" (48.3 cm) 31/32” (7.7 cm) 11/8” (2.9 cm) 11” (27.9 cm) 4” (10.2 cm) K. 21" (53.3 cm) L. 205/16" (51.6 cm) M. 87/8" (22.5 cm) N 13/32" (1.0 cm) O. 115/32" (3.7 cm) P. 9" (22.9 cm) Q. 315/32" (8.8 cm) R. 317/32" (9.0 cm) S. 51/2" (14.0 cm) T. 4" (10.2 cm) Recirculation Assembly (Accessory) Internal (Non Ducted) Venting N F D A G B Center Line of Down Draft Intake C Plan View of Cutouts A E C F D E Front of Cabinet G H H K A Kick Plate L A. 19" (48.3 cm) B. 53/4" (14.6 cm) C. 7" (17.8 cm) D. 15/16” (2.4 cm) J E. F. G. H. 171/8" (43.5 cm) 131/8" (33.3 cm) 21/2" (6.4 cm) 243/64" (61.1 cm) B M A. B. C. D. E. F. G. 183/8" (46.6 cm) 33/4" (9.5 cm) 53/4" (14.7 cm) 63/4" (17.1 cm) 9 16 / " (14 mm) 9 16 / ” (14 mm) 97/8" (25.0 cm) H. 175/8" (44.8 cm) J. 33/32" (7.8 cm) K. 2" (5.0 cm) L. 3/16" (4.8 mm) diameter (4) M. 5/16" (7.9 mm) N. 17" (43.2 cm) Center line of Down Draft Intake Recirculation Cover (Part of Recirculation Kit) A Pedestal C B A. 181/2" (47.0 cm) B. 331/32" (10.1 cm) C. 11/16" (1.7 cm) Pedestal A B Reinforce all joints C Plywood 3/4" [1.9 cm] A. 11" (27.9 cm) B. 13" (33 cm) C. 73/4" (19.7 cm) 7 Venting Requirements IMPORTANT: This appliance must be exhausted outdoors unless you are using the Recirculation Accessory Kit. See the “Venting Methods” section and the “Accessories” section in your Use and Care manual to order. ■■ Do not terminate the vent system in an attic or other enclosed area. ■■ Vent system must terminate to the outside. ■■ Use only a 3Z\v" x 10" (8.3 cm x 25.4 cm) rectangular metal vent or 6" (15.2 cm) round metal vent. Rigid metal vent is recommended. Do not use plastic or metal foil vent. ■■ Before making cutouts, make sure there is proper clearance within the wall or floor for the exhaust vent. ■■ Do not cut a joist or stud unless absolutely necessary. If a joist or stud must be cut, then a supporting frame must be constructed. ■■ The size of the vent should be uniform. ■■ The vent system must have a damper. ■■ Use vent clamps and metal duct tape to seal all joints in the vent system. ■■ Use caulking to seal exterior wall or roof opening around the cap. Cold Weather Installations An additional backdraft damper should be installed to minimize backward cold air flow and a thermal break installed to minimize conduction of outside temperatures as part of the vent system. The damper should be on the cold air side of the thermal break. Makeup Air Local building codes may require the use of makeup air systems when using ventilation systems greater than specified CFM of air movement. The specified CFM varies from locale to locale. Consult your HVAC professional for specific requirements in your area. Venting Methods Common venting methods are shown for a counter-mounted downdraft cooktop. The cooktop may be vented through the wall or floor. Option 1 – Roof Venting Option 2 – Wall Venting B Determine which venting method is best for your application. For Best Performance: ■■ ■■ Use 26-gauge minimum galvanized or 25-gauge minimum aluminum metal vent. Poor quality pipe fittings can reduce airflow. For external venting, flexible metal vent is not recommended. NOTE: Local codes may require a heavier gauge material. ■■ Metal duct may be reduced to 30-gauge galvanized steel or 26-gauge aluminized steel if allowed by local codes. This reduction is based on information in the International Residential Codes Section M1601.1 (2006 edition). ■■ Avoid installing 2 elbows together. ■■ Use no more than three 90° elbows. ■■ If an elbow is used, install it as far away as possible from the hood’s vent motor exhaust opening. ■■ Make sure there is a minimum of 18" (45.7 cm) of straight vent between the elbows if more than one elbow is used. Elbows too close together can cause excess turbulence that reduces airflow. ■■ Do not use a 5" (12.7 cm) elbow in a 6" (15.2 cm) or 3¼" x 10" (8.3 cm x 25.4 cm) system. ■■ Do not reduce to a 5" (12.7 cm) system after using a 6" (15.2 cm) or 3¼" x 10" (8.3 cm x 25.4 cm) fittings. ■■ Avoid forming handmade crimps. Handmade crimps may restrict airflow. ■■ Use a Jenn-Air® vent cap for proper performance. If an alternate wall or roof cap is used, be certain the cap size is not reduced and that it has a backdraft damper. ■■ Use vent clamps and metal duct tape to seal all joints in the vent system. Use caulking to seal exterior wall or roof opening around the cap. The length of vent system and number of elbows should be kept to a minimum to provide efficient performance. The maximum equivalent length of the vent system is 35 ft (10.7 m). For altitudes above 4,500 ft (1272 m), reduce recommended vent run by 20% for best performance. ■■ 8 B A A A. 6” (15.2 cm) round ducting transitioned to 31/4" x 10" (8.3 cm x 25.4 cm) rectangular floor venting B. Roof cap A. 6” (15.2 cm) round ducting B. Wall cap Option 3 – Venting Between Floor Joist Front view of cabinet with doors removed B A A. 6” (15.2 cm) round wall venting B. Wall cap External Venting Dimensional Planning Single Unit with 6" (15.2 cm) External Discharge ■■ This configuration accommodates one or two 15" (38.1 cm) cooktops, one on either or each side of the downdraft intake. A Center Line of Downdraft Inlet Center Line of Blower Discharge Option: Two Downdrafts with Single 8" (20.3 cm) External Discharge ■■ This configuration accommodates three 15" (38.1 cm) cooktops, one between downdraft intakes and one on each side of the down draft intakes. ■■ Order Y-Transition Ducting Kit: W11180669 A B C Center Line Downdraft Intake D Center Line T- Ducting Transition Center Line Downdraft Intake Center Line Blower Intake Center Line Cutout Cutout Opening Depth Cutout Opening Width A. 623/32" (16.2 cm) Option: Two Downdrafts with Single 8" (20.3 cm) External Discharge ■■ This configuration accommodates one or two 15" (38.1 cm) cooktops and a 30" (76.2 cm) or 36" (91.4 cm) cooktop. As shown, the 30" (76.2 cm) or 36" (91.4 cm) (note: 30" [76.2 cm] cooktop requirement shown, add 6" [15.2 cm] to the 189/64" [46.1 cm] dimension for a 36" [91.4 cm] cooktop) cooktop would be located between downdraft intakes and the 15" (38.1 cm) on the left side of the larger cooktop. A second 15" (38.1 cm) cooktop can be located on the right side of the 30" (76.2 cm)/36" (91.4 cm) cooktop. ■■ For a 30" (76.2 cm)/36" (91.4 cm) cooktop and single 15" (38.1 cm) cooktop on the right hand side of the cooktop, the dimensions shown are to be applied as a mirror image. ■■ Y-Transition Ducting Kit: W11180669 Center Line of Downdraft intake E C F B G A D A. B. C. D. 195/64" (48.8 cm) 1529/32" (40.4 cm) 623/64" (16.2 cm) Center line blower intake Center Line of Downdraft Intake H Center line of Blower Intake Center Line of Cutout Cutout Opening Depth 45° 6" (15.2 cm) Elbow Center line of Blower Intake Cutout Opening Width A. B. C. D. E. 337/8" (86 cm) 345/64" (86.5 cm) 1547/64" (40 cm) 189/64" (46.1 cm) 623/64" (16.2 cm) F. Center line of blower intake G. Center line of Y ducting transition H. 6" (15.2 cm) ducting to size 9 Concrete Slab Installations – Exhaust Through Wall A O N M Vent Piece 6" (15.2 cm) Round 6" (15.2 cm) to 3Z\v" x 10" (8.3 cm x 25.4 cm) 90° elbow transition 5.0 ft (1.5 m) E F 3Z\v" x 10" (8.3 cm x 25.4 cm) 90° elbow 5.0 ft (1.5 m) H G J I 3Z\v" x 10" (8.3 cm x 25.4 cm) flat elbow 5.0 ft (1.5 m) 3Z\v" x 10" (8.3 cm x 25.4 cm) wall cap 0.0 ft (0.0 m) B C D L K A. Wall cap B. 6" (15.2 cm) round metal vent C. 16" (40.6 cm) maximum D. 6" (15.2 cm) round PVC sewer pipe E. 6” (15.2 cm) round elbow F. 6” round duct as required G. 6" (15.2 cm) round PVC coupling H. Concrete slab I. 6" (15.2 cm) round PVC sewer pipe J. 6" (15.2 cm) round 90° PVC sewer pipe elbow K. Tightly pack gravel or sand completely around pipe. L. 30 ft (9.1 m) maximum M. 6" (15.2 cm) round 90° PVC sewer pipe elbow N. 6" (15.2 cm) round PVC coupling O. 12" (30.5 cm) minimum Example vent system wall cap 90˚ elbow 6 ft (1.8 m) 2 ft (0.6 m) Calculating Vent System Length To calculate the length of the system you need, add the equivalent feet (meters) for each vent piece used in the system. Vent Piece 6" (15.2 cm) Round 45° elbow 2.5 ft (0.8 m) 90° elbow 5.0 ft (1.5 m) 1 - 90° elbow = 5 ft (1.5 m) 8 ft (2.4 m) straight = 8 ft (2.4 m) 1 - wall cap = 0 ft (0 m) System length = 13 ft (3.9 m) NOTE: A flexible vent is not recommended. Flexible vents create back pressure and air turbulence that greatly reduce performance. Recirculation: Non-Vented (Recirculating) Installations Only 6" (15.2 cm) wall cap 0.0 ft (0.0 m) 3Z\v" x 10" (8.3 cm x 25.4 cm) to 6" (15.2 cm) transition 4.5 ft (1.4 m) 6" (15.2 cm) to 3Z\v" x 10" (8.3 cm x 25.4 cm) transition 1 ft (0.3 m) 3Z\v" x 10" (8.3 cm x 25.4 cm) to 6" (15.2 cm) 90° elbow transition 5.0 ft (1.5 m) 10 You will need to order: ■■ Recirculation Kit part number W10807915 (See the “Assistance or Service” section in your Use and Care manual to order.) ■■ You may also need a section of 3Z\v" x 10" (8.3 cm x 25.4 cm) metal duct – length required is determined by the distance from the exhaust outlet to the back flat surface of the Recirculation Kit housing. INSTALLATION INSTRUCTIONS Mounting Bracket Installation Install Foam Strips Downdraft Intake Gasket (Foam Strip) Surface Bridge Bracket Adjusting Screw Adjusting Direction (Bridge Bracket) Bracket-A Bracket-B 1. Mount Bracket-A to downdraft body. Screws are in place on downdraft body. 2. a) Mount Bracket-B to Bracket-A. Position short leg of “B” against “A” for mounting to front or rear of cabinet. This results in minimum extension of bracket positioning. HINT: Pre-drive screws into Bracket-A. b) Position long leg of “B” against “A” for maximum extension of bracket position. Positioning will be determined by final location of the downdraft in the cabinet/counter top. 3. To fasten Bracket-B to cabinet, assemble “B” to “A” per instruction (Item-2). Snug screws to allow “B” to be positioned against cabinet (front or rear). Position downdraft intake unit in its final position in countertop. Secure screws holding Bracket-B to “A”. Use wood screws (not provided) to secure Bracket-B to front and rear of cabinet. NOTE: The mounting brackets must be secured to the cabinet, front and rear. The front of the cabinet must have a secure wood surface to mount the bracket to. Depending on the cabinet construction a wooden brace (1 x 2 or equivalent) may be required to be added to the cabinet. Determine planned position of downdraft in cabinet and secure brace to cabinet. Downdraft Cabinet Wood Brace 1. If the right side of the downdraft is positioned against the countertop, remove and discard the bridge, do not remove screws. If the right side of the downdraft is positioned adjacent to a cooktop, adjust the position of the bridge bracket to be level with the top of the countertop. NOTE: The bridge kit included with a 15" (38.1 cm) module cannot be used on the right side of the downdraft. The bridge bracket provides the required foam strip surface. 2. Install foam strips, cut to size, on the counter top (front and rear) and left side supporting surface (bridge kit or counter top) and on the downdraft bridge bracket. Recirculation (Non-ducted) Installation Cabinet Cutouts for Non-ducted Installations 1. After laying out the positioning of the desired cooktop and downdraft units to be installed determine the location of the centerline of the downdraft intake. Mark out the required cut out in the cabinet floor and kick plate. It is recommended that the complete layout of downdraft and cooktop(s) be established before cutting any openings. 2. Countertop and cabinet can now be cut to the prepared requirements. 3. Assemble the 6" (15.2 cm) round elbow to 6" (15.2 cm) 31/4" x 10” (8.3 cm x 25.4 cm) transition (stack boot) to 31/4" x 10” (8.3 cm x 25.4 cm) elbow to recirculating assembly. Secure all joints and seal using the aluminum metal duct tape. This assembly can now be dropped into the opening in the cabinet floor. 4. Secure the recirculation assembly to the kick plate. 5. Assemble the blower to the pedestal using supplied brackets and use wood screws (not supplied) to secure blower to pedestal. 6. Position assembly from item-5 onto cabinet floor to engage 6” elbow on assembly from item-3. Secure joint and seal with aluminum duct tape. 7. Position prepared downdraft intake into cabinet and engage with blower assembly intake. Secure and seal duct joints 8. Anchor the pedestal to the cabinet floor with wood screws. 9. Assemble the downdraft mounting brackets previously described. 10. Assemble the recirculation cover to the recirculation assembly in the cabinet kick plate. 11. Option: The opening in the cabinet floor can be covered to trim out the cabinet interior. 11 Install Cooktop, Downdraft and Blower Motor Assembly Rear Discharge Prepare Blower Motor Assembly Vented 1. Assemble the 2-piece telescoping round duct to the blower motor assembly top duct extension. Secure with screw and metal duct tape. A B Internal (Non Ducted) Venting and Right Discharge C A. Intake transition B. Telescoping round duct C. Blower motor Alternate Blower Configuration 1. After establishing the location of the products to be installed. The blower can be configured to support the desired ducting location. 2. Prepare the blower assembly for installation and assemble the two hold down brackets supplied to he blower. 3. Locate the downdraft in the countertop. 4. Assemble the supplied transition for connection to the blower assembly using 4-screws supplied. 5. Assemble the telescoping duct, supplied to the blower assembly. Secure all joints and seal using aluminum tape. 6. Use wood screws to secure the blower to the cabinet floor using the 2-brackets supplied. Secure one at the front and one at the rear. Left Discharge 12 Complete Installation 1. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped. 2. Check that you have all your tools. 3. Dispose of/recycle all packaging materials. 4. Use a mild solution of liquid household cleaner and warm water to clean cooktop and/or vent before use. Dry thoroughly with a soft cloth. For more information, see the “Cooktop Care” and “Vent Care” sections of the Use and Care manuals. 5. See the “Cooktop Use” and “Vent Use” sections of the Use and Care manuals for operating instructions. If you need Assistance or Service: Please reference the “Warranty” section of your Use and Care manual. WARNING Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. 6. Plug into a grounded 3 prong outlet. 7. Test cooktop and downdraft to confirm all are working. NOTE: If the cooktop and/or vent does not work after turning on the power, check that a circuit breaker has not tripped or a household fuse has not blown. See the “Troubleshooting” section of your Use and Care manual for further information. 13 WIRE DIAGRAM GREEN C LED STRIP 12V DC 2.4 W USER INTER. LED LAMP SWITCH 1 2 HOLD ELECTRO DOOR MAGNET CLOSED 1 DC 12V .33A 2 PANEL SWITCH A G POWER BLACK L1 SUPPLY WHITE N 3 12V DC MAIN BOARD B On Board L1 E.M.C Filter N CAPACITOR MOTOR A - NO OPERATION UNTIL DOOR IS CLOSED. B - 12V RED & BLACK OUTPUT IS ENERGIZED HOLDING THE DOOR OPEN AND TURNS ON LED STRIP. C - ONCE B HAS BEEN ENERGIZED USER INTERFACE IS NOW ACTIVE. 14 LOW HI GH N MOTOR OUTPUTS GREY BLA CK RED BLA CK LOW VOLTAGE 12 V DC YELLOW - LOW GND BLUE - HIGH GREEN MOTOR PLUG YELLOW BLUE WHITE MOTOR max. 245W amps 2.42 120 volts WHITE W11170792A / ® TM ©2017 Jenn-Air. Used under license in Canada. All rights reserved. 10/17
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021