GE UVC9300SLSS Installation Guide

Add to my manuals
40 Pages

advertisement

GE UVC9300SLSS Installation Guide | Manualzz
INSERT HOODS
Custom
SAFETY INFORMATION
...........3
USING THE HOOD
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Chef Connect . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Wi-Fi Connect . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
CARE AND CLEANING
OWNER’S MANUAL &
INSTALLATION
INSTRUCTIONS
UVC9300
UVC9360
Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Surfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
INSTALLATION INSTRUCTIONS . . 9
TROUBLESHOOTING TIPS. . . . . . . .
17
LIMITED WARRANTY . . . . . . . . . . . . .
18
ACCESSORIES . . . . . . . . . . . . . . . . . . . . .
19
CONSUMER SUPPORT . . . . . . . . . . . . 20
Write the model and serial
numbers here:
Model # _________________
Serial # _________________
ESPAÑOL
Para consultar una version en
español de este manual de
instrucciones, visite nuestro sitio de
internet GEAppliances.com.
You can find them on a label on
the inside of the hood.
GE is a trademark of the General Electric Company. Manufactured under trademark license.
49-80813-2 07-18 GEA
THANK YOU FOR MAKING GE APPLIANCES A PART OF YOUR HOME.
Whether you grew up with GE Appliances, or this is your first, we’re happy to have you in the family.
We take pride in the craftsmanship, innovation and design that goes into every GE Appliances
product, and we think you will too. Among other things, registration of your appliance ensures that we
can deliver important product information and warranty details when you need them.
Register your GE appliance now online. Helpful websites and phone numbers are available in the
Consumer Support section of this Owner’s Manual. You may also mail in the pre-printed registration
card included in the packing material.
2
49-80813-2
WARNING TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
A. Use this unit only in the manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
B. Before servicing or cleaning unit, switch power off
at service panel and lock the service disconnecting
means to prevent power from being switched
on accidentally. When the service disconnecting
means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the
service panel.
C. Do not use this unit with any solid-state speed
control device.
D. This unit must be grounded.
CAUTION FOR GENERAL VENTILATING USE
ONLY. DO NOT USE TO EXHAUST HAZARDOUS
OR EXPLOSIVE MATERIALS AND VAPORS.
WARNING TO REDUCE THE RISK OF INJURY
TO PERSONS IN THE EVENT OF A RANGE TOP
GREASE FIRE, OBSERVE THE FOLLOWING*:
A. SMOTHER FLAMES with a close-fitting lid, cookie
sheet or metal tray, then turn off the burner. BE
CAREFUL TO PREVENT BURNS. If the flames do
not go out immediately, EVACUATE AND CALL
THE FIRE DEPARTMENT.
B. NEVER PICK UP A FLAMING PAN—You may be
burned.
C. DO NOT USE WATER, including wet dishcloths or
towels—a violent steam explosion will result.
D. Use an extinguisher ONLY if:
1. You know you have a Class ABC extinguisher,
and you already know how to operate it.
2. The fire is small and contained in the area where
it started.
3. The fire department is being called.
4. You can fight the fire with your back to an exit.
*Based on “Kitchen Fire Safety” published by NFPA.
SAFETY INFORMATION
IMPORTANT SAFETY INFORMATION
READ ALL INSTRUCTIONS BEFORE USING
CAUTION TO REDUCE RISK OF FIRE AND
TO PROPERLY EXHAUST AIR, BE SURE TO DUCT
AIR OUTSIDE. DO NOT VENT EXHAUST AIR INTO
SPACES WITHIN WALLS OR CEILINGS OR INTO
ATTICS, CRAWL SPACES OR GARAGES.
READ AND SAVE THESE INSTRUCTIONS
49-80813-2
3
SAFETY INFORMATION
IMPORTANT SAFETY INFORMATION
READ ALL INSTRUCTIONS BEFORE USING
WARNING TO REDUCE THE RISK OF A
C. When cutting or drilling into wall or ceiling, do not
damage electrical wiring and other hidden utilities.
RANGE TOP GREASE FIRE:
D. Ducted fans must always be vented to the outdoors.
A. Never leave surface units unattended at high
settings. Boilovers cause smoking and greasy
spillovers that may ignite. Heat oils slowly on
medium settings.
E. When applicable, install any makeup (replacement)
air system in accordance with local building
code requirements. Visit GEAppliances.com for
available makeup air solutions.
B. Always turn hood ON when cooking at high heat or
when flambéing food (i.e. Crepes Suzette, Cherries
Jubilee, Peppercorn Beef Flambé).
F. Turn off breaker to adjacent rooms while working.
C. Clean ventilating fans frequently. Grease should not
be allowed to accumulate on fan or filter.
USE ONLY METAL DUCTWORK.
D. Use proper pan size. Always use cookware
appropriate for the size of the surface element.
WARNING TO REDUCE THE RISK OF FIRE,
WARNING TO REDUCE THE RISK OF FIRE,
Ŷ'RQRWDWWHPSWWRUHSDLURUUHSODFHDQ\SDUWRI\RXU
hood unless it is specifically recommended in this
manual. All other servicing should be referred to a
qualified technician.
ELECTRIC SHOCK OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
A. Installation work and electrical wiring must be
done by qualified person(s) in accordance with all
applicable codes and standards, including fire-rated
construction.
B. Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney) of
fuel burning equipment to prevent back drafting.
Follow the heating equipment manufacturer’s
guidelines and safety standards such as those
published by the National Fire Protection
Association (NFPA), the American Society for
Heating, Refrigeration and Air Conditioning
Engineers (ASHRAE) and the local code authorities.
How to Remove Protective Shipping Film and Packaging Tape
Carefully grasp a corner of the protective shipping film
with your fingers and slowly peel it from the appliance
surface. Do not use any sharp items to remove the film.
Remove all of the film before using the appliance for the
first time.
To assure no damage is done to the finish of the
product, the safest way to remove the adhesive from
packaging tape on new appliances is an application of
a household liquid dishwashing detergent. Apply with a
soft cloth and allow to soak.
NOTE: The adhesive must be removed from all parts.
NOTE: For further cleaning instructions/suggestions,
please refer to the Care and Cleaning section.
READ AND SAVE THESE INSTRUCTIONS
4
49-80813-2
7
3
4
8
7
5
6
2
1
3
4
2
5
Remote Control
1. Rangehood Control Panel: The control panel
5. Chef Connect: This is a Bluetooth® pairing feature
is located on the front of the canopy. The position
and function of each control button are noted below.
for use with other compatible Chef Connect enabled
products on a cooktop or range. When the device is
paired, the light and fan will turn ON at the Default
Sync Settings upon receiving a command from the
range or cooktop. It will remain ON at that setting until
the user changes it. To pair devices, hold down the
Chef Connect button for 3 seconds. To turn it back
off, hold the button down for another 3 seconds, see
the Chef Connect section for details.
2. Fan On/Off Button: On/Off switch for the fan.
The fan can be operated by pressing any of the fan
setting buttons. Hold for 3 seconds to activate Delay
Off feature, which automatically turns the fan off
after 15 minutes.
3. Fan Setting Button: Speed control for the
fan. Press the Low button for LOW speed, Med for
MEDIUM speed, and High for HIGH speed. Hold
down the High button for 3 seconds to activate the
BOOST speed that will run for 10 minutes.
On Remote, press Up to increase fan speed, press
Down to decrease fan speed, including Boost.
4. Light Button: On/Dim/Off switch for the LED
lights. Press the Light button to turn the lights on,
again to set the lights to dim setting, and again to
turn the lights off.
USING THE HOOD: Controls
Controls
6. IR Sensor: Remote control reciever when used
with Remote Control Kit (UXRC1).
7. Wi-Fi: Hold down the Light and Chef Connect
buttons for 3 seconds to activate the Wi-Fi. The
Wi-Fi light turns on when connected, see the Wi-Fi
Connect section for details. On Remote, press Wi-Fi
to toggle Wi-Fi function.
8. Delay Off (Remote only): Press and hold
Delay Off to toggle Delay Off function.
Heat Sensor
Your hood is equipped with a HEAT SENSOR
thermostat. This thermostat is a device that will turn on
or speed up the blower if it senses excessive heat above
the cooking surface.
Ŷ,IEORZHULV2IILWWXUQVEORZHU2QWR0HGVSHHG
Ŷ,IEORZHULV2QDWDORZHUVSHHGVHWWLQJLWWXUQV
blower up to Med speed.
When the temperature level drops to normal, the blower
will return to its original setting.
49-80813-2
5
USING THE HOOD: Chef Connect / Wi-Fi Connect
Chef Connect
Chef Connect Operation Bluetooth® Connection
To pair with another device:
Default Sync Settings:
To start the pairing process on the hood, press and hold
the Chef Connect button for 3 seconds. The backlight
for the Low-Med-High-Light-Chef Connect buttons will
flash in that sequence until the hood is paired with the
range or other device. If the pairing is successful, all five
backlights (Low, Med, High, Light, Chef Connect) will
flash simultaneously three times and then turn off and
the backlight for the Chef Connect button will turn on.
The factory default setting for the light will be the
brightest.
It will time out after 2 minutes if the pairing is not
completed, after which the pairing sequence will need to
be restarted.
To cancel pairing:
To cancel the pairing, hold the Chef Connect button
down for 3 seconds and then turn off the hood.
The factory default setting for the fan sync will be OFF.
The user can change the Default Sync Settings by
pressing and holding the Low button for 3 seconds. This
will enter the Default Settings Mode. Once in this mode,
the backlights for all buttons (Low, Med, High, Light,
Chef Connect) will blink On/Off indefinitely and the fan
and light will switch to the current Default Sync Setting,
so the user knows what the current default value is.
At this time, set the light and fan to the desired default
levels. Once the user is satisfied with the selection,
press and hold the On/Off button for 3 seconds. This
will exit this mode. At that time the backlights will stop
blinking and the state of the fan and light will change
back to their prior state before entering the Default
Settings Mode.
Wi-Fi Connect
Connecting your Wi-Fi Connect Enabled hood (on some models)
Your GE Appliances hood is designed to provide you with two-way communication between your appliance and smart
device. By using the GE Appliances Wi-Fi Connect features, you will be able to control essential hood operations such
as fan speed, light functions, timer/clock function, delay off and filter reset using your smartphone or tablet.*
Connect your GE Appliances hood
What you will need
1. On your smart phone or tablet visit
Your GE Appliances hood uses your existing home Wi-Fi
GEAppliances.com/connect to learn more about
network to communicate between the appliance and your
connected appliance features and to download the
smart device. In order to setup your GE Appliances hood,
appropriate app.
you will need to gather some information:
1. Each GE Appliances hood has a connected
2. Follow the app onscreen instructions to connect your
appliance information label that includes an
GE Appliances hood.
Appliance Network Name and Password. These
3. Once the process is complete, the connection light
are the two important details that you will need to
located on your GE Appliances hood display will stay
connect to the appliance. The label is located on the
on solid and the app will confirm you are connected.
side of the unit behind the filters.
4. If the connection light does not turn on or is blinking,
follow the instructions on the app to reconnect. If
Connected Appliance Information
issues continue please call 800.220.6899 and ask for
assistance regarding hood wireless connectivity.
Network: ************
FCC ID: ZKJ-WCATA005
To
connect
additional smart devices, repeat steps 1 and 2.
Password: **********
IC: 10229A-WCATA001
Note that any changes or modifications to the remote
MAC ID: ************
enable device installed on this hood that are not
Sample Label
expressly approved by the manufacturer could void the
user’s authority to operate the equipment.
2. Have your smart phone or tablet ready with the ability
to access the internet and download apps.
3. You will need to know the password of your home
Wi-Fi router. Have this password ready while you are
setting up your GE Appliances hood.
* Compatible Apple or Android devices and home Wi-Fi network required.
6
49-80813-2
Be sure the circuit breaker is off and all surfaces are cool before cleaning or servicing any part of the vent hood.
The metal baffles channel grease released by foods on the cooktop into the drip trays. The baffles also help prevent
flaming foods on the cooktop from damaging the inside of the hood.
The baffles must ALWAYS be in place when the hood is in use. The grease baffles and drip trays are dishwashersafe and should be cleaned every month, depending on usage of the hood.
Grease Drip Tray
To install:
Place and seat the drip trays into the designated hood
track. Slide them left or right until all trays are side-byside in place in the track.
To remove:
Carefully, use the grease tray lip to lift the tray upwards
and out. The tray will be free of the designated hood track.
To clean:
Swish the drip tray in hot soapy water and rinse in clean
water or wash it in the dishwasher. Do not use abrasive
cleaners.
Drip Tray Replacement
CARE AND CLEANING: Filters
Filters
NOTE: Some discoloration of the filter may occur in the
dishwasher.
Baffle Metal Grease Filter
To install:
Insert the top of the baffle into the track behind the
control panel. The arrows on the side of the baffle
should be pointing towards the front of the unit. Slide
the baffle up and push the bottom end back until it firmly
seats into place.
1
To remove:
Use front knob to pull filter forward, towards the control
panel. The bottom of the filter becomes free of the
grease drip tray. Use back knob to pull the baffle away
from the track behind the control panel.
2
Baffle Replacement
It is important for baffles to be placed correctly with
arrows on the side pointing towards the front of the
unit to channel grease to the drip trays and avoid
grease accumulation in the baffles.
To clean:
Swish the filter in hot soapy water and rinse in clean
water or wash it in the dishwasher. Do not use abrasive
cleansers.
Baffle Removal
NOTE: Some discoloration of the filter may occur in the
dishwasher.
49-80813-2
7
CARE AND CLEANING: Surfaces / Lights / Filters
Filters (Cont.)
Charcoal Filter (for recirculation installation only)
NOTE: DO NOT rinse, or put charcoal filter in an
automatic dishwasher.
The charcoal filter is included with the unit. It cannot
be cleaned; it must be replaced. It is recommended
that the charcoal filter be replaced every 6 months or
if it is noticeably dirty or discolored.
Order Charcoal Filter UXCF91
To inquire about purchasing replacement charcoal filters
or to find the location of a dealer nearest you, please call
our toll-free number:
National Parts Center 800.626.2002
To Install
1. Remove the grease filters. See Filters section.
2. Install the charcoal filter mounts to either side of the
motor using three screws per side.
3. Insert the tab on the charcoal filter into the triangular
slot on the mount.
4. Clip the charcoal filter in until it is locked
5. Repeat with second filter on the other side of the
motor.
6. Reattach the metal filters. See Filters section.
To Remove
1. Remove grease filters-See Filters section
2. Unclip the charcoal filter by pressing the release clip.
3. Carefully remove charcoal filter from tab.
Charcoal Filter Mount
Surfaces
Stainless Steel Surfaces (on some models)
Do not use a steel wool pad; it will scratch the
surface.
Use only a liquid cleanser free of grit and rub in the
direction of the brush lines with a damp soft sponge.
To clean the stainless steel surface, use warm sudsy
water or a stainless steel cleaner or polish. Always wipe
the surface in the direction of the brush line. Follow
the cleaner instructions for cleaning the stainless steel
surface. Cleaners with oxalic acid such as Bar Keepers
Friend Soft Cleanser™ will
remove surface rust, tarnish, and
small blemishes. To receive a
coupon for a trial sample of Bar
Keepers Friend Soft Cleanser™
follow the link below or scan the
QR Code.
To inquire about purchasing stainless steel appliance
cleaner or polish, or to find the location of a dealer
nearest you, please call our toll-free number:
National Parts Center
800.626.2002
GEApplianceParts.com
barkeepersfriend.com/ge
Lights
CAUTION Allow lights to cool before touching.
1. Before attempting to replace the lights, make sure that
the light switch is turned off.
2. Rotate light counterclockwise to unlock and pull out.
Wearing latex gloves may offer a better grip.
3. Replace with new light of same type, making sure
pins are inserted properly into the sockets of the lamp
holder and turn clockwise to lock.
All lamps need to be GU10 compatible.
8
Lamp
Holder
Rotate the lamp until the
pins are located in narrow
neck of the socket to lock.
49-80813-2
Custom Insert Hood
UVC9300, UVC9360
“If you have questions, call GE Appliances at 800.GE.CARES (800.432.2737)
or visit our website at: GEAppliances.com”
BEFORE YOU BEGIN
Read these instructions completely and
carefully.
Ŷ
Ŷ
IMPORTANT
— Save these
instructions for local inspector’s use.
IMPORTANT — Observe all governing
codes and ordinances.
Ŷ Note to Installer – Be sure to leave these
instructions with the Consumer.
Ŷ Note to Consumer – Keep these instructions for
future reference.
Ŷ Skill level – Installation of this vent hood requires
basic mechanical and electrical skills.
Ŷ Completion time – Approximately 1 to 3 hours
Ŷ Proper installation is the responsibility of the
installer.
Ŷ Product failure due to improper installation is not
covered under the Warranty.
CAUTION Due to the weight and size of
these vent hoods and to reduce the risk of personal
injury or damage to the product, TWO PEOPLE
ARE REQUIRED FOR PROPER INSTALLATION.
FOR YOUR SAFETY
WARNING Before beginning the installation,
switch power off at service panel and lock the
service disconnecting means to prevent power from
being switched on accidentally. When the service
disconnecting means cannot be locked, securely
fasten a prominent warning device, such as a tag,
to the service panel.
49-80813-2
WARNING TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
A. Installation work and electrical wiring must be
done by qualified person(s) in accordance with
all applicable codes and standards, including
fire-rated construction.
B. Sufficient air is needed for proper combustion
and exhausting of gases through the flue
(chimney) of fuel burning equipment to prevent
back drafting. Follow the heating equipment
manufacturer’s guidelines and safety standards
such as those published by the National Fire
Protection Association (NFPA), the American
Society for Heating, Refrigeration and Air
Conditioning Engineers (ASHRAE) and the local
code authorities.
C. When cutting or drilling into wall or ceiling, do
not damage electrical wiring and other hidden
utilities.
D. Ducted fans must always be vented to the
outdoors.
E. Turn off breaker to adjacent rooms while
working.
INSTALLATION INSTRUCTIONS
Installation
Instructions
WARNING TO REDUCE THE RISK OF FIRE,
USE ONLY METAL DUCT WORK.
WARNING Disconnect all electrical power
at the main circuit breaker or fuse box before
installing.
9
INSTALLATION PREPARATION
Installation Preparation
PRODUCT DIMENSIONS
INSTALLATION CLEARANCES
This vent hood must be installed between the 24"
required minimum and 36" recommended maximum
above the cooking surface.
Ŷ$OZD\VUHIHUWRWKHFRRNWRSRUUDQJHLQVWDOODWLRQ
instructions for product-specific clearances.
6-15/16"
Design varies by model
11-1/2"
12"
3-1/8"
1-15/16"
NOTE: Installation height should be measured
from the cooking surface to the bottom edge of the
cabinet surface.
NOTE: UL requires any combustible surface to be a
minimum of 30" above the cooking surface. Lower
combustible surfaces may be covered to meet
requirements.
Ŷ7KHFXVWRPFDELQHWLQWHUQDOKHLJKWPXVWEH
18-1/2" minimum for vertical venting and 29"
minimum for recirculation.
18" or 24"
9"
Ŷ7KLVKRRGFDQEHYHQWHGWRWKHRXWGRRUVRULW
can be installed for recirculating operation. For
recirculating operation, refer to Recirculating
Installation Planning.
4-1/4"
Ŷ7KLVKRRGPD\EHPRXQWHGLQDZDOOFDELQHWRU
installed over an island.
28-1/4" or
34-1/4"
19-1/8"
18-1/2" min.
11-1/2"
CABINET PREPARATION
*24" Minimum required
*36" Maximum recommended
FRONT VIEW
18-1/2" min.
11-1/2"
Typically 36"
1"
1"
NOTE: The exhaust duct on the hood is closer to
the rear of the hood. It is important to plan for the
alignment to the connection point of the hood.
SIDE VIEW
29" min.
6-1/2"
11-1/2"
3"
10
1"
49-80813-2
TOOLS AND MATERIALS REQUIRED (NOT SUPPLIED)
Needle-nose pliers
Aluminized
duct tape
Pencil and tape measure
Electric drill and
appropriate bits
Step ladder
Safety glasses
Level
8" ducting and
caps as needed
Flashlight
Tin snips
Wire cutter/
stripper
UL listed wire nuts
Phillips and flat-blade
screwdrivers
PARTS PROVIDED
Strain relief for
junction box
Gloves
INSTALLATION PREPARATION
Installation Preparation
PLAN THE INSTALLATION
Locate the parts packed with the hood.
NOTE: The hardware bag may contain extra pieces
to accommodate a variety of installation methods
for various models.
CAUTION To reduce risk of fire and to
properly exhaust air, be sure to duct the air
outside – Do not vent exhaust air into spaces
within walls or ceilings or into attics, crawl
spaces, or garages.
WARNING
PERSONAL INJURY HAZARD
It is recommended that 2 people are used to
install the range hood. Failure to properly
lift rangehood could result in damage to the
product or personal injury.
Hardware Bag
Hood
A
NOTE: This rangehood can be installed as either
ducted or recirculation. In a ducted application,
this rangehood can be vented through the wall
or ceiling. When installed for recirculation, the
rangehood vents back into the room.
B
Phillips Head
Wood Screws
3/16" x 1-1/2"
(QTY: 4)
Philips Head
Machine Screw
1/8" X 3/8"
(QTY: 16)
D
Phillips Head
Wood Screws
1/8" X 3/8" (QTY: 4)
49-80813-2
Damper
Assembly
L
Phillips Head
Wood Screws
3/16" x 1"
(QTY: 8)
REMOVE THE PACKAGING
CAUTION Wear gloves to protect against
sharp edges.
Ŷ Remove the hardware bag, literature package
and other boxed parts.
Ŷ Remove and properly discard the protective
plastic wrapping and other packaging materials.
11
INSTALLATION PREPARATION
Installation Preparation
ADVANCE PLANNING
ADVANCE PLANNING (CONT.)
Duct Install Planning
Custom Cabinet Frame Planning
ŶThe custom canopy or cabinet should have a
rectangular hole to accommodate the custom
hood insert by itself. This hole is the same
size for both a wall installation and an island
installation. Ensure parallelism and levelness of
the cabinet so that it doesn't affect flushness of
the hood with the cabinet.
Ŷ7KLVKRRGLVGHVLJQHGWREHYHQWHGYHUWLFDOO\
through the ceiling. Use a 8" round duct. Use
locally supplied elbows to vent horizontally
through the rear wall.
Ŷ8VHPHWDOGXFWZRUNRQO\
Ŷ'HWHUPLQHWKHH[DFWORFDWLRQRIWKHYHQWKRRG
Front of hole
must be 3"
minimum from
cabinet front
ŶPlan the route for venting exhaust to the outdoors.
To maximize the ventilation performance of the
vent system:
1. Minimize the duct run length and number of
transitions and elbows.
2. Maintain a constant duct size.
Back of hole
must be 1"
minimum from
back wall
Depth
Width
3. Seal all joints with duct tape to prevent any leaks.
NOTE: Flexible vent is not recommended. Flexible
vent creates back pressure and air turbulence that
greatly reduces performance.
Ŷ0D[LPXPHTXLYDOHQWGXFWOHQJWKIRU&)0
150 foot for vent hoods.
Ŷ,QVWDOODZDOOFDSRUURRIFDSZLWKGDPSHUDWWKH
exterior opening. Purchase the wall or roof cap
and any transition and length of duct needed in
advance.
ŶWhen applicable, install any makeup (replacement)
air system in accordance with local building
code requirements. Visit GEAppliances.com for
available makeup air solutions.
UVC9300
UVC9360
Width (in.)
28-1/4
34-1/4
Depth (in.)
19-1/8
19-1/8
RECIRCULATION INSTALL PLANNING
This hood may be installed in recirculation mode.
The charcoal filter is necessary for recirculation
installation and is included with the unit.
Vent system can terminate either through the roof
RUWKHZDOO7RYHQWWKURXJKDZDOOD๦HOERZLV
needed and installed immediately above the hood.
Roof Cap
Add Insulation
and/or Caulk
Cabinet
Round Duct
Wall Cap
Add tape to joint
Hood
Add Insulation
and/or Caulk
Wall and Ceiling Framing for Adequate Support
This vent hood is heavy and the cabinet
structure needs to support the weight of the
loaded insert sleeve. Adequate structural support
must be provided in all types of installations.
Ŷ,QVWDOODWLRQZLOOEHHDVLHULIWKHYHQWKRRGLV
installed before the cooktop is installed.
12
49-80813-2
POWER SUPPLY
IMPORTANT – (Please read carefully)
WARNING
FOR PERSONAL SAFETY, THIS APPLIANCE
MUST BE PROPERLY GROUNDED.
Remove house fuse or open circuit breaker before
beginning installation.
Do not use an extension cord or adapter plug with
this appliance. Follow National Electrical Codes or
prevailing local codes and ordinances.
Electrical supply
These vent hoods must be supplied with 120V,
60Hz, and connected to an individual, properly
grounded branch circuit, and protected by a 15 or
20 amp circuit breaker or time delay fuse.
Ŷ Wiring must be 2 wire with ground.
ŶIf the electrical supply does not meet the above
requirements, call a licensed electrician before
proceeding.
ŶRoute house wiring as close to the installation
location as possible in the ceiling or wall.
ŶConnect the wiring to the house wiring in
accordance with local codes.
Grounding instructions
The grounding conductor must be connected to
a ground metal, permanent wiring system, or an
equipment-grounding terminal or lead on the hood.
PREPARE FOR CABINET
INSTALLATION
NOTE: This bracket must be removed prior to
installation. Remove 2 back (rear) and 2 bottom
screws per illustration bellow.
INSTALLATION PREPARATION
Installation Preparation
1. Securely press the damper on top of the exhaust
opening. Check that the damper opens freely.
Attach damper to hood using screws (B) provided.
WARNING
The improper connection of the
equipment-grounding conductor can result in a risk
of electric shock. Check with a qualified electrician
or service representative if you are in doubt whether
the appliance is properly grounded.
PREPARE HOUSE ELECTRICAL
WIRING
The custom cabinet must allow spacing for house
wiring to reach junction box located in diagram
below. If unit is installed over an island, the wiring
must come from ceiling. If power cord is needed,
accessory is available.
18" or 24"
Electrical
Area
9-1/2"
5-3/4"
or
8-3/4"
49-80813-2
2. The hood should be centered left to right over
the cooktop.
3. Remove and properly discard the protective
plastic wrapping from the hood.
4. The back surface of the hood must be 1"
minimum from the back wall. The front surface
of the hood must be 3" minimum from the front
custom cabinet panel.
5. The custom cabinet should provide for
removal of panels to provide access to the
electrical wiring and to the ducting and its
connections to the hood in case of any need
for servicing or other reasons.
13
INSTALLATION
Installation
STEP 1 INSTALL THE HOOD
ELECTRICAL CONNECTION
1. Remove the electrical junction box cover.
1. Confirm the damper is in place in the hood
exhaust opening, see previous page for
instructions.
2. Insert the hood into the cabinet opening.
2. Remove the electrical box knockout.
Electrical Box
Knockout with
Strain Relief
3. Feed the Power Supply Cable through the hole
and secure with a strain relief.
3. Fasten with 8 screws [(A), (L) or (D) as needed],
4 in the front and 2 on each side, toward the
back of the hood. It is recommended to start
with one corner and fasten screws diagonally to
ensure unit flushness with cabinet.
4. Attach the white lead of the power supply (A) to
the white lead of the range hood (D) with a wire
nut. Attach the black lead of the power supply (B)
to the black lead of the range hood (C) with a wire
nut. Connect the house ground wire under the
green grounding screw (E).
E
A
House Wiring
B
D
C
Hood Wiring
4. Once the hood is in place, seal the duct to the
hood with duct tape (Do not use screws).
14
5. Reattach the electrical junction box cover.
49-80813-2
INSTALLATION
Installation
STEP 2 RECIRCULATION OPTION (IF USED)
1. Cut a hole into the soffit for the exhaust duct.
2. Install the vent grill over the exhaust duct.
3. Seal the duct joints with duct tape.
Visit GEAppliances.com to order the optional recirculation kit.
Soffit Cutout
6-15/16"
90° Angle Boot
Hood Center Line
11-1/2"
8” ducting
Filters
STEP 3 FINALIZE INSTALLATION
1. Insert filters, see the Filters section.
2. Check operation of the lights and blower.
3. Finish the custom cabinetry.
49-80813-2
15
INSTALLATION
Installation
MAKE UP AIR TECHNOLOGY
Note to Installers and Inspectors: This product comes equipped with a simple installation feature that limits
maximum CFM levels in order to comply with certain local codes or regulations. This installation method may not
be necessary for all installations, please refer to your local codes for further guidelines.
CAUTION Hood must be disconnected from main power prior performing the conversion instructions
listed below. Failure to do so could result in personal injury or damage to the product.
To modify unit (if needed for local codes):
390CFM or 290CFM
By design, the maximum blower speed is greater than
400 CFM. For local codes requiring reduced CFM,
modify the wiring as described below:
1. Remove the baffles, see Filters section.
2. Remove the control board box cover.
3. Locate the motor harness plugged into the control
board.
4. A - For a maximum of 390 CFM
Unit can operate with 4 speeds
(Low, Medium, High, Boost).
1. Disconnect the connector of the blue wire
from the red wire.
Control Board Box Cover
2. Connect the 2 red wires together.
3. Cut off the blue unused connector and crimp
the end if desired.
B - For a maximum of 290 CFM
Unit can operate with 3 speeds
(Low, Medium, High).
1. Disconnect the connector of the blue wire
from the red wire.
Motor Harness Connector
2. Cut off the blue unused connector and crimp
the end if desired.
5. Reattach the control board box cover and install
baffles.
Note to Inspectors: To verify this product was
installed in either configuration, check motor wiring
connections as described above.
Red
Blue
Red
Motor Harness
16
49-80813-2
Save time and money! Review the charts on the following pages first and you may not need to call for service.
Problem
Possible Cause
What To Do
Fan/Light does not
operate when button is
turned ON
A house fuse may be blown or a circuit
breaker tripped.
Replace fuse or reset circuit breaker.
Loud or abnormal
airflow noise
Wrong duct size used in installation.
This hood requires 8” ducting to perform optimally.
Using smaller duct pipe will cause reduced venting.
Minimize the duct run length and number of transitions
and elbows. GE Appliances service technicians cannot
correct this issue if installed improperly.
Fan fails to circulate
air or moves air slower
than normal and/or
fan is making loud or
abnormal airflow noise
Obstructions in duct work.
Make sure nothing is blocking the vent. Make sure
your wall or roof cap has a blade or door.
Damper blade on wall or roof cap may
not be open.
Make sure damper swings freely. Damper blades may
flip over and will not fully open when this happens.
Adjust to original position.
Metal grease filter and charcoal filter
(if present) may be dirty.
Clean the metal grease filter and replace charcoal filter
(if present). See Care and Cleaning of the Vent Hood.
Insufficient makeup (replacement) air
Sufficient makeup (replacement) air is required for
exhausting appliances to operate to rating. Check with
local building codes, which may require or strongly
advise the use of makeup air. Visit GEAppliances.com
for available makeup air solutions.
Early light failure
Light wattage is too high.
Replace with correct wattage.
Fan automatically turns
on and can not be
turned off.
This is normal.
The sensor feature will automatically turn the fan on if
cooking temperature becomes too hot. The fan will then
turn off when temperatures cool to an appropriate level.
Fan keeps going off
and on
The motor is probably overheating and
turning itself off. This can be harmful to
the motor.
Check to be sure the filters are clean. If off and on
cycling continues, call for service.
Lights not functioning
Wrong bulbs are used. Must use GU10
compatible dimmable bulbs.
Visit GEAppliances.com for replacement bulbs.
No grease captured in
the drip trays
No grease captured in the drip trays
Install the baffles properly making sure the arrows on
the sides of the baffles are pointing towards the front of
the unit so that the grease openings on the bottom of
the baffles are inserted in the drip trays, see the Filters
section.
Hood will not work
remotely
Router issues, no wireless signal, etc.
For assistance with hood wireless network connectivity,
please call 800.220.6899.
49-80813-2
Hood is not connected.
TROUBLESHOOTING TIPS
Troubleshooting tips ... Before you call for service
17
LIMITED WARRANTY
GE Appliances Vented Range Hood Limited Warranty
GEAppliances.com
All warranty service is provided by our Factory Service Centers, or an authorized Customer Care® technician. To
schedule service online, visit us at geappliances.com/service_and_support/, or call GE Appliances at 800.GE.CARES
(800.432.2737). Please have your serial number and your model number available when calling for service.
Servicing your appliance may require the use of the onboard data port for diagnostics. This gives a GE Appliances factory
service technician the ability to quickly diagnose any issues with your appliance and helps GE Appliances improve its
products by providing GE Appliances with information on your appliance. If you do not want your appliance data to be
sent to GE Appliances, please advise your technician not to submit the data to GE Appliances at the time of service.
For the period of
GE Appliances will replace
One year
From the date
of the original
purchase
Any part of the cooking product which fails due to a defect in materials or workmanship.
During this limited one-year warranty, GE Appliances will provide, free of charge, all labor
and related service costs to replace the defective part.
What GE Appliances will not cover:
Ŷ Service trips to your home to teach you how to use
Ŷ Damage to finish, such as surface rust, tarnish, or small
Ŷ
Ŷ
Ŷ Incidental or consequential damage caused by
Ŷ
Ŷ
the product.
Improper installation, delivery, or maintenance.
Failure of the product if it is abused, misused,
modified, or used for other than the intended purpose
or used commercially.
Replacement of house fuses or resetting of circuit
breakers.
Damage to the product caused by accident, fire,
floods, or acts of God.
blemishes not reported within 48 hours of delivery.
possible defects with this appliance.
Ŷ Damage caused after delivery.
Ŷ Product not accessible to provide required service.
Ŷ Service to repair or replace light bulbs, except for LED
lamps.
Staple your receipt here. Proof of the original purchase
date is needed to obtain service under the warranty.
EXCLUSION OF IMPLIED WARRANTIES
Your sole and exclusive remedy is product repair as provided in this Limited Warranty. Any implied warranties,
including the implied warranties of merchantability or fitness for a particular purpose, are limited to one year or
the shortest period allowed by law.
This limited warranty is extended to the original purchaser and any succeeding owner for products purchased for home
use within the USA. If the product is located in an area where service by a GE Appliances Authorized Servicer is not
available, you may be responsible for a trip charge or you may be required to bring the product to an Authorized GE
Appliances Service location for service. In Alaska, the limited warranty excludes the cost of shipping or service calls to
your home.
Some states do not allow the exclusion or limitation of incidental or consequential damages. This limited warranty
gives you specific legal rights, and you may also have other rights which vary from state to state. To know what your
legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.
Warrantor: GE Appliances, a Haier company
Louisville, KY 40225
Extended Warranties: Purchase a GE Appliances extended warranty and learn about special discounts that are
available while your warranty is still in effect. You can purchase it online anytime at
geappliances.com/service_and_support/shop-for-extended-service-plans.htm
or call 800.626.2224 during normal business hours. GE Appliances Service will still be there after your warranty expires.
18
49-80813-2
Looking For Something More?
GE Appliances offers a variety of accessories to
improve your cooking and maintenance experiences!
Refer to the Consumer Support page for phone numbers
and website information.
The following products and more are available:
Parts
Power Cord Kit
ACCESSORIES
Accessories
Make-up Air Kit
Charcoal Filter
Recirculation Kit
Remote Control
Cleaning Supplies
CitruShine™ Stainless Steel Wipes
CERAMA BRYTE® Stainless Steel Appliance Cleaner
Bar Keepers Friend Soft Cleanser™
49-80813-2
19
CONSUMER SUPPORT
Consumer Support
GE Appliances Website
Have a question or need assistance with your appliance? Try the GE Appliances Website 24 hours a day, any day
of the year! You can also shop for more great GE Appliances products and take advantage of all our on-line support
services designed for your convenience. In the US: GEAppliances.com
Register Your Appliance
Register your new appliance on-line at your convenience! Timely product registration will allow for enhanced
communication and prompt service under the terms of your warranty, should the need arise. You may also mail in
the pre-printed registration card included in the packing material. In the US: GEAppliances.com/register
Schedule Service
Expert GE Appliances repair service is only one step away from your door. Get on-line and schedule your service at
your convenience any day of the year. In the US: GEAppliances.com/service
or call 800.432.2737 during normal business hours.
Extended Warranties
Purchase a GE Appliances extended warranty and learn about special discounts that are available while your
warranty is still in effect. You can purchase it on-line anytime. GE Appliances Services will still be there after your
warranty expires. In the US: GEAppliances.com/extended-warranty
or call 800.626.2224 during normal business hours.
Remote Connectivity
For assistance with wireless network connectivity (for models with remote enable),
visit our website at GEAppliances.com/connected-home-smart-appliances/ or call 800.220.6899 in the US.
Parts and Accessories
Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes
(VISA, MasterCard and Discover cards are accepted). Order on-line today 24 hours every day.
In the US: GEApplianceparts.com or by phone at 877.959.8688 during normal business hours.
Instructions contained in this manual cover procedures to be performed by any user. Other servicing
generally should be referred to qualified service personnel. Caution must be exercised, since improper
servicing may cause unsafe operation.
Contact Us
If you are not satisfied with the service you receive from GE Appliances, contact us on our Website with all the
details including your phone number, or write to:
In the US: General Manager, Customer Relations | GE Appliances, Appliance Park | Louisville, KY 40225
GEAppliances.com/contact
Printed in China
20
49-80813-2
Estándares
CAMPANAS DE INSERCIÓN
INFORMACIÓN DE SEGURIDAD
....3
USO DE LA CAMPANA
Controles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Chef Connect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Conexión Wi-Fi . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
CUIDADO Y LIMPIEZA
MANUAL DEL
PROPIETARIO E
INSTALACIÓN
UVC9300
UVC9360
Filtros . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Superficies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Lámparas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
INSTRUCCIONES
DE INSTALACIÓN . . . . . . . . . . . . . . . . . . 9
CONSEJOS PARA LA SOLUCIÓN
DE PROBLEMAS . . . . . . . . . . . . . . . . . . .
GARANTÍA LIMITADA
ACCESORIOS
17
. . . . . . . . . . . . . . 18
. . . . . . . . . . . . . . . . . . . . . . . . 19
SOPORTE PARA
EL CONSUMIDOR . . . . . . . . . . . . . . . . . . 20
Escriba los números de modelo y
de serie aquí:
Nº de Modelo ____________
Nº de Serie ______________
Los encontrará en una etiqueta
dentro de la campana.
GE es una marca registrada de General Electric Company. Fabricado bajo licencia de marca.
49-80813-2 07-18 GEA
GRACIAS POR HACER QUE GE APPLIANCES SEA PARTE DE SU HOGAR.
Ya sea que haya crecido usando GE Appliances, o que ésta es su primera vez, nos complace
tenerlo en la familia.
Sentimos orgullo por el nivel de arte, innovación y diseño de cada uno de los electrodomésticos de
GE Appliances, y creemos que usted también. Entre otras cosas, el registro de su electrodoméstico
asegura que podamos entregarle información importante del producto y detalles de la garantía
cuando los necesite.
Registre su electrodoméstico GE ahora a través de Internet. Sitios Web y números telefónicos útiles
están disponibles en la sección de Soporte para el Consumidor de este Manual del Propietario.
También puede enviar una carta en la tarjeta de inscripción preimpresa que se incluye con
el material embalado.
2
49-80813-2
ADVERTENCIA
PARA REDUCIR EL RIESGO
DE INCENDIO, DESCARGA ELÉCTRICA O LESIONES A
PERSONAS, CUMPLA CON LOS SIGUIENTES PUNTOS:
A. Utilice esta unidad sólo de la manera concebida por el
fabricante. Si tiene alguna pregunta, comuníquese con el
fabricante.
B. Antes de realizar reparaciones o limpiar la unidad,
desconecte la energía del panel de servicio y bloquee los
medios de desconexión para evitar el accionamiento de
la energía de manera accidental. Cuando los medios de
desconexión de servicio no pueden bloquearse, coloque
sobre el panel de servicio un dispositivo de advertencia
bien visible, como una etiqueta.
C. No utilice esta unidad con ningún dispositivo de control
de velocidad de estado sólido.
D. Esta unidad debe estar conectada a tierra.
PRECAUCIÓN
SÓLO PARA USO DE
VENTILACIÓN GENERAL. NO LO UTILICE PARA
ELIMINAR MATERIALES Y VAPORES PELIGROSOS O
EXPLOSIVOS.
PRECAUCIÓN
PARA REDUCIR EL RIESGO
DE INCENDIO Y PARA ELIMINAR EL AIRE DE ESCAPE
CORRECTAMENTE, ASEGÚRESE DE DIRIGIR EL AIRE
DEL CONDUCTO HACIA EL EXTERIOR. NO VENTILE EL
AIRE DE ESCAPE EN ESPACIOS DENTRO DE PAREDES
O CIELORRASOS O EN ÁTICOS, HUECOS SANITARIOS
O GARAJES.
ADVERTENCIA
PARA REDUCIR EL RIESGO DE
LESIONES A PERSONAS EN CASO DE UN INCENDIO
DE GRASA SOBRE UNA ESTUFA, CUMPLA CON LOS
SIGUIENTES PUNTOS*:
A. APAGUE LAS LLAMAS con una tapa que ajuste bien,
una plancha para galletas o una bandeja de metal, y
luego apague el quemador. TENGA MUCHO CUIDADO
A FIN DE EVITAR QUEMADURAS. Si las llamas no
se apagan de inmediato, SALGA DE LA VIVIENDA Y
LLAME AL DEPARTAMENTO DE BOMBEROS.
B. NUNCA LEVANTE UNA SARTÉN EN LLAMAS—
Usted puede quemarse.
C. NO UTILICE AGUA, incluyendo repasadores o toallas
húmedos—se provocará una violenta explosión de vapor.
D. Utilice un extintor SÓLO si:
1. Usted sabe que cuenta con un extintor Clase ABC y
ya sabe cómo utilizarlo.
2. El incendio es pequeño y se contuvo en el área donde
comenzó.
INFORMACIÓN DE SEGURIDAD
INFORMACIÓN IMPORTANTE DE SEGURIDAD
LEA TODAS LAS INSTRUCCIONES ANTES DE USAR
3. Se está llamando al departamento de bomberos.
4. Usted puede combatir el incendio con su espalda
dirigida hacia una salida.
*Basado en “Kitchen Fire Safety” publicado por NFPA.
LEA Y GUARDE ESTAS INSTRUCCIONES
49-80813-2
3
INFORMACIÓN DE SEGURIDAD
INFORMACIÓN IMPORTANTE DE SEGURIDAD
LEA TODAS LAS INSTRUCCIONES ANTES DE USAR
ADVERTENCIA
PARA REDUCIR EL RIESGO DE
UN INCENDIO DE GRASA SOBRE UNA ESTUFA:
A. Nunca deje unidades de superficie desatendidas en
configuraciones de calor elevadas. Los alimentos que
hierven y se derraman provocan humo y derrames
grasosos que pueden prenderse fuego. Caliente los
aceites lentamente en configuraciones bajas o medias.
B. Siempre encienda el sistema de ventilación cuando
cocine con configuraciones de calor elevadas o cuando
flambee alimentos (por ej., Crepes Suzette, cerezas
Jubilee, carne flambeada a la pimienta en grano).
C. Limpie los ventiladores con frecuencia. No debe
permitirse la acumulación de grasa en el ventilador o en
el filtro.
D. Utilice el tamaño de recipiente adecuado. Siempre utilice
recipientes de cocción apropiados para el tamaño del
elemento de superficie.
C. Al cortar o perforar una pared o un cielorraso, no dañe el
cableado eléctrico y de otros servicios ocultos.
D. Los ventiladores con conducto siempre deben contar con
ventilación hacia el exterior.
E. Cuando corresponda, instale un sistema de reposición
(reemplazo) de aire de acuerdo con los requisitos
del código local de construcción. Para acceder a
soluciones relacionadas con la reposición de aire, visite
GEAppliances.com.
F. Desconecte el disyuntor de habitaciones adyacentes
mientras esté trabajando.
ADVERTENCIA
A FIN DE REDUCIR EL RIESGO
DE INCENDIOS, USE SÓLO CONDUCTOS DE METAL.
Ŷ1RLQWHQWHUHSDUDURUHHPSOD]DUQLQJXQDSDUWHGHOD
cocina, a menos que esto se recomiende específicamente
en este manual. Cualquier otra reparación deberá ser
realizada por un técnico calificado.
ADVERTENCIA
A FIN DE REDUCIR EL
RIESGO DE INCENDIOS, DESCARGAS ELÉCTRICAS
O LESIONES PERSONALES, CUMPLA CON LO
SIGUIENTE:
A. El trabajo de instalación y el cableado eléctrico deben
ser realizados por una persona(s) calificada de acuerdo
con todos los códigos y estándares aplicables, incluyendo
construcciones resistentes al fuego.
B. Es necesario contar con suficiente cantidad de aire
para una combustión y salida de gases adecuadas a
través del conducto (chimenea) del equipo de consumo
de combustible, a fin de evitar ráfagas de aire. Siga las
pautas del fabricante del equipo de calefacción y los
estándares de seguridad, tales como aquellos publicados
por la Asociación Nacional de Protección contra
Incendios (National Fire Protection Association, NFPA), la
Sociedad Estadounidense para la Calefacción (American
Society for Heating), los Ingenieros de Refrigeración
y Acondicionadores de Aire (Refrigeration and Air
Conditioning Engineers, ASHRAE) y las autoridades de
los códigos locales.
Cómo Retirar la Película Protectora de Envío y la Cinta de Embalaje
Con cuidado tome un extremo de la película protectora
de envío con los dedos y lentamente retire la misma de la
superficie del electrodoméstico. No utilice ningún producto
filoso para retirar la película. Retire toda la película antes de
usar el electrodoméstico por primera vez.
Para asegurar que no haya daños sobre el acabado del
producto, la forma más segura de retirar el adhesivo de la cinta
de embalaje en electrodomésticos nuevos es aplicando un
detergente líquido hogareño para lavar platos. Aplique con una
tela suave y deje que se seque.
NOTA: El adhesivo deberá ser eliminado de todas las partes.
No se puede retirar si se hornea con éste dentro.
NOTA: Para acceder a más instrucciones/ sugerencias, por
favor consulte la sección de Cuidado y Limpieza.
LEA Y GUARDE ESTAS INSTRUCCIONES
4
49-80813-2
7
3
4
8
7
5
6
2
1
3
4
2
5
Control Remoto
1. Panel de Control de la Campana Extractora:
5.
Chef Connect: Ésta es una función de emparejamiento
de Bluetooth® para uso con otros productos compatibles
con Chef Connect en una superficie de cocción o una
cocina. Cuando el dispositivo es emparejado, la luz y
el ventilador se encenderán en Default Sync Settings
(Configuraciones de Sincronización por Omisión), al recibir
una orden desde la cocina o la superficie de cocción.
Permanecerá en ON (Encendido) en esa configuración
hasta que el usuario la modifique. Para emparejar
dispositivos, mantenga presionado el botón Chef Connect
durante 3 segundos. Para volver a apagarlo, mantenga
presionado el botón durante otros 3 segundos; para más
detalles, consulte la sección de Chef Connect.
6.
Sensor IR: Receptor del Control Remoto cuando es
usado con el Kit del Control Remoto (UXRC1).
7.
Wi-Fi: Mantenga presionados los botones Light (Luz)
y Chef Connect durante 3 segundos para activar el
Wi-Fi. La luz del Wi-Fi se enciende cuando se encuentra
conectada; para más detalles, consulte la sección Wi-Fi
Connect. En la función Remote (Remoto), presione Wi-Fi
para pasar a esta función.
El panel de control está ubicado en el frente de la base.
La posición y función de cada botón del control aparece
escrito debajo.
2.
Botón Fan On/Off (Ventilador Encendido/
Apagado): Interruptor de Encendido/Apagado del
ventilador. El ventilador puede ser usado presionando
cualquiera de los botones de configuración del
ventilador. Mantenga presionado el botón durante 3
segundos para activar la función Delay Off (Retraso
Apagado), el cual apaga de forma automática el
ventilador durante 15 minutos.
3.
Botones de la Configuración del Ventilador:
Control de velocidad del ventilador. Presione el botón Low
(Baja) para usar la velocidad BAJA, Med para MEDIUM
(Media) y High para HIGH (Alta). Mantenga presionado
el botón High (Alto) durante 3 segundos para activar la
función BOOST speed (Aumento de Velocidad), la cual
funcionará durante 10 minutos. En la función Remote
(Remoto), presione Up (Arriba) para incrementar la
velocidad del ventilador, y Down (Abajo) para reducir la
velocidad del ventilador, incluyendo Boost (Aumentado).
4.
Botón de Luz: Interruptor de Encendido/ Atenuado/
Apagado de las luces LED. Presione la tecla LIGHT (Luz)
para encender las luces, nuevamente para ajustar las
luces en la configuración atenuada, y una vez más para
apagar las luces.
8.
USO DE LA CAMPANA: Controles
Controles
Delay Off (Retraso Apagado) (Sólo Remoto):
Mantenga presionada la tecla Delay Off (Retraso
Apagado) para pasar a esta función.
Sensor de Calor
Su campana está equipada con un termostato con SENSOR
DE CALOR. Este termostato es un dispositivo que se enciende
o acelera el calefactor si siente calor excesivo sobre la
superficie de cocción.
Ŷ6LHOFDOHIDFWRUHVWiHQ2II $SDJDGR ±HQFLHQGHHO
calefactor en velocidad Media.
Ŷ6LHOFDOHIDFWRUHVWiHQ2Q (QFHQGHU HQXQDFRQILJXUDFLyQ
GHYHORFLGDGEDMD±VXEHHOFDOHIDFWRUDYHORFLGDG0HGLD
Cuando el nivel de temperatura baja hasta el nivel normal, el
calefactor regresa a su configuración original.
49-80813-2
5
USO DE LA CAMPANA: Chef Connect / Conexión Wi-Fi
Chef Connect
Conexión de Bluetooth® al Funcionamiento de Chef Connect
Para emparejar con otro dispositivo:
Configuraciones de Sincronización por Omisión:
A fin de iniciar el proceso de emparejamiento, mantenga
presionado el botón Chef Connect durante 3 segundos. La luz
de fondo de los botones Low-Med-High-Light-Chef Connect (BajaMedia-Alta-Luz-Chef Connect) parpadeará en dicha secuencia
hasta que la campana esté emparejada con la cocina u otro
dispositivo. Si el emparejamiento es exitoso, las cinco luces de
fondo (Baja, Media, Alta, Luz, Chef Connect) parpadearán de
forma simultánea tres veces y luego se apagarán y la luz de
fondo del botón Chef Connect se encenderá.
La configuración por omisión de fábrica de la luz será la más
brillante.
Se desactivará luego de 2 minutos si el emparejamiento no es
completado. Luego de esto, la secuencia de emparejamiento
deberá ser reiniciada.
Para cancelar el emparejamiento:
Para cancelar el emparejamiento, mantenga presionada la tecla
Chef Connect durante 3 segundos y luego apague la campana.
La configuración por omisión de fábrica de la sincronización
del ventilador estará APAGADA.
El usuario podrá modificar las Configuraciones de
Sincronización por Omisión manteniendo presionado el botón
Low (Baja) durante 3 segundos. Esto permitirá ingresar a
Default Settings Mode (Modo de Configuraciones por Omisión).
Una vez en este modo, las luces de fondo de todos los
botones (Baja, Media, Alta, Luz, Chef Connect) parpadearán
encendiéndose y apagándose de forma indefinida, y el
ventilador y la luz pasarán a la Configuración de Sincronización
por Omisión actual, de modo que el usuario sepa cuál es el
valor por omisión actual. En este momento, configure la luz y
el ventilador en los niveles por omisión deseados. Una vez que
el usuario se encuentre satisfecho con la selección, se deberá
mantener presionado el botón On/Off (Encendido/ Apagado)
durante 3 segundos. Esto hará que se abandone este modo.
En este momento, las luces de fondo dejarán de parpadear
y el estado del ventilador y de la luz volverán a cambiar a
su estado anterior, antes de entrar en Default Settings Mode
(Modo de Configuraciones por Omisión).
Conexión Wi-Fi
Conecte su campana con Conexión Habilitada de Wi-Fi (en algunos modelos)
Su campana de GE Appliances está diseñado para brindarle una comunicación recíproca entre su electrodoméstico y el
dispositivo inteligente. Al usar las funciones de la conexión Wi-Fi de GE Appliances, usted podrá controlar funciones esenciales
de su campana tales como las configuraciones de velocidad del ventilador, función de la luz, función del temporizador/ reloj,
retraso apagado y reinicio del filtro utilizando su teléfono inteligente o tableta*.
Qué necesitará
Conexión de su campana de GE Appliances
Su campana de GE Appliances utiliza su red de Wi-Fi hogareña
1. A través de su teléfono inteligente o tableta, visite
existente para realizar la comunicación entre el electrodoméstico
GEAppliances.com/connect para aprender más sobre las
y su dispositivo inteligente. A fin de configurar su campana de
funciones del electrodoméstico conectado y para descargar
GE Appliances, usted necesitará reunir cierta información:
la aplicación correspondiente.
1. Cada campana de GE Appliances cuenta con una etiqueta
2. Siga las instrucciones en pantalla de la aplicación para
informativa del electrodoméstico conectado, que incluye
conectar su campana de GE Appliances.
un Nombre y Contraseña de Red del Electrodoméstico.
3. Una vez que el proceso se haya completado, la luz
Estos son los dos detalles importantes que necesitará para
de conexión ubicada en la pantalla de su campana
conectar el electrodoméstico. La etiqueta está ubicada al
GE Appliances, permanecerá en sólido y la aplicación
costado de la unidad, detrás de los filtros.
confirmará que usted está conectado.
4. Si la luz de conexión no se enciende o está titilando, siga
las instrucciones en la aplicación para volver a realizar la
Connected Appliance Information
conexión. Si continúan los problemas, comuníquese al
800.220.6899 y solicite asistencia en relación a la
Network: ************
FCC ID: ZKJ-WCATA005
conectividad inalámbrica del campana.
Password: **********
IC: 10229A-WCATA001
Para conectar dispositivos inteligentes adicionales, repita los
MAC ID: ************
pasos 1 y 2.
Ejemplo de Etiqueta
Observe que todos los cambios o modificaciones al dispositivo
de acceso remoto instalado en este campana que no están
2. Su teléfono inteligente o tableta deben estar preparados
expresamente aprobados por el fabricante podrían anular la
con la capacidad de acceder a Internet y descargar
autoridad del usuario para operar el equipamiento.
aplicaciones.
3. Usted deberá conocer la contraseña del enrutador Wi-Fi de
su hogar. Tenga esta contraseña a mano al configurar el
campana de GE Appliances.
* Se requiere el uso de dispositivos y de una red Wi-Fi hogareña que sean compatibles con Apple o Android.
6
49-80813-2
Asegúrese de que la energía eléctrica esté apagada y que todas las superficies estén frías antes de limpiar o arreglar cualquier
pieza de la campana de ventilación.
Los deflectores metálicos hacen circular la grasa liberada por las comidas en la superficie de cocción sobre las bandejas de
goteo. Los deflectores también evitan que las llamas de las comidas en la superficie de cocción dañen el interior de la campana.
Los deflectores SIEMPRE deberán ser colocados cuando la campana se encuentre en uso. Los deflectores de grasa y las
bandejas de goteo son de uso seguro en lavavajillas y deberán ser limpiados cada mes, dependiendo del uso de la campana.
Bandeja de Goteo de Grasa
Para instalar:
Coloque e instale las bandejas de goteo en los espacios
designados de la campana. Deslice las mismas sobre la
izquierda o derecha hasta que todas las bandejas estén
posicionadas sobre sus espacios una al lado de la otra.
Para quitar:
Con cuidado, use el borde de la bandeja de grasa para
levantar la bandeja hacia arriba y afuera. La bandeja estará
libre del espacio designado en la campana.
Para limpiar:
Reemplazo de la Bandeja de Goteo
Coloque la bandeja de goteo en agua caliente con jabón y
enjuague la misma con agua limpia o lávela en el lavavajillas.
No use limpiadores abrasivos.
CUIDADO Y LIMPIEZA: Filtros
Filtros
NOTA: Cierta descoloración del filtro podrá producirse en el
lavavajillas.
Filtro de Grasa Metálico con Deflector
Para instalar:
Inserte la parte superior del deflector en el espacio detrás
del panel de control. Las flechas que están al costado del
deflector deberán apuntar hacia el frente de la unidad. Deslice
el deflector hacia arriba y empuje el extremo hacia atrás hasta
que se ajuste de manera firme en su posición.
1
Para quitar:
Use la perilla frontal para empujar el filtro hacia adelante, hacia
el panel de control. La parte inferior del filtro se libera de la
grasa de la bandeja de goteo. Use la perilla trasera para retirar
el deflector de su espacio detrás del panel de control.
2
Reemplazo del Deflector
Es importante que los deflectores sean colocados de forma
correcta con las flechas laterales apuntando hacia el frente
de la unidad, a fin de dirigir la grasa hasta las bandejas de
goteo y evitar su acumulación en los deflectores.
Para limpiar:
Coloque el filtro en agua caliente con jabón y enjuague el
mismo con agua limpia o lávelo en el lavavajillas. No use
limpiadores abrasivos.
NOTA: Cierta descoloración del filtro podrá producirse en el
lavavajillas.
49-80813-2
Retiro del Deflector
7
CUIDADO Y LIMPIEZA: Superficies / Lámparas / Filtros
Filtros (Cont.)
Filtro de carbón (Sólo Para Instalación con Recirculación)
NOTA: NO enjuague o coloque el filtro de carbón en el
lavavajillas automático.
El filtro de carbón no puede ser limpiado. Debe ser
reemplazado. Se recomienda que el filtro de carbón
sea reemplazado cada entre 6 meses, o si se encuentra
notoriamente sucio o descolorido.
Solicite el filtro de carbón UXCF91.
Para consultar sobre la compra de filtros de carbón de
repuesto o para encontrar la ubicación del distribuidor más
cercano a su domicilio, llame a nuestro número gratuito:
4. Enganche el filtro de carbón hasta que quede bloqueado.
5. Repita esto con el segundo filtro del otro lado del motor.
6. Vuelva a adherir los filtros metálicos. Consulte la sección
de Filtros.
Para retirar
5HWLUHORVILOWURVGHJUDVD±&RQVXOWHODVHFFLyQGH)LOWURV
2. Desenganche el filtro de carbón presionando el sujetador
para liberarlo.
3. Con cuidado retire el filtro de carbón de la lengüeta.
Montaje del Filtro de Carbón
Centro nacional de piezas 800.626.2002
Para instalar
1. Retire los filtros de grasa. Consulte la sección de Filtros.
2. Instale los montajes del filtro de carbón sobre cada lado del
motor, usando tres tornillos por lado.
3. Inserte la lengüeta que se encuentra en el filtro de carbón
dentro de la ranura triangular del montaje.
Superficies
Superficies de acero inoxidable (en algunos modelos)
No utilice almohadillas de acero porque rayan la
superficie.
Para limpiar la superficie de acero inoxidable, utilice agua
tibia jabonosa o un limpiador o lustrador de acero inoxidable.
Siempre limpie la superficie en dirección de la veta. Siga las
instrucciones del producto para limpiar la superficie de acero
inoxidable. Los limpiadores con ácido oxálico tales como Bar
Keepers Friend Soft Cleanser™
eliminarán el óxido sobre la superficie,
deslustres y pequeñas manchas. Para
recibir un cupón para una muestra de
Bar Keepers Friend Soft Cleanser™,
ingrese al siguiente link o escanee el
Código QR.
Use sólo un limpiador líquido libre de material abrasivo y frote
en la dirección de las líneas del cepillo con una esponja suave
y húmeda.
Para consultar sobre la compra de limpiadores o lustradores
de aparatos de acero inoxidable, o para encontrar la ubicación
del distribuidor más cercano, llame a nuestro número gratuito:
Centro nacional de piezas
800.626.2002
GEApplianceParts.com
barkeepersfriend.com/ge
Lámparas
PRECAUCIÓN
Espere a que las lámparas se
enfríen antes de tocar las mismas.
1. Antes de intentar reemplazar una lámpara, asegúrese de
que su interruptor esté apagado.
2. Gire la lámpara en dirección contraria a las agujas del reloj
para desbloquear y extraer la misma. Colocarse guantes de
látex puede brindar un mejor agarre.
3. Reemplace por una lámpara nueva del mismo tipo,
asegurándose de que las clavijas queden correctamente
insertadas en las fichas del portalámparas y gire en
dirección de las agujas del reloj para bloquear la lámpara.
Portalámparas
Gire la lámpara hasta que los pernos
queden ubicados en el cuello angosto
del enchufe generando el bloqueo.
Todas las lámparas deben ser compatibles con GU10.
8
49-80813-2
Campana de Inserción Estándar
UVC9300, UVC9360
“Ante cualquier duda, llame a GE Appliances al 800.GE.CARES (800.432.2737)
o visite nuestro sitio Web en: GEAppliances.com”
ANTES DE COMENZAR
Lea estas instrucciones por completo y con
detenimiento.
•
IMPORTANTE — Guarde estas
instrucciones para el uso de inspectores locales.
•
IMPORTANTE
— Cumpla con todos los
códigos y ordenanzas vigentes.
• Nota al instalador ±$VHJ~UHVHGHGHMDUHVWDV
instrucciones con el Consumidor.
• Nota al consumidor ±&RQVHUYHHVWDVLQVWUXFFLRQHV
para referencia futura.
• Nivel de capacidad ±/DLQVWDODFLyQGHHVWDFDPSDQD
de ventilación requiere capacidades mecánicas y
eléctricas básicas.
• Tiempo de compleción ±$SUR[LPDGDPHQWHHQWUH
1 y 3 horas
• El instalador tiene la responsabilidad de efectuar una
instalación adecuada.
• La Garantía no cubre las fallas del producto debido a
una instalación incorrecta.
PRECAUCIÓN
Debido al peso y tamaño de
estas campanas de ventilación, y a fin de reducir el
riesgo de lesiones personales o daños sobre el producto
- SE DEBERÁ CONTAR CON DOS PERSONAS PARA
UNA INSTALACIÓN ADECUADA.
ADVERTENCIA
PARA REDUCIR EL RIESGO
DE INCENDIO, DESCARGA ELÉCTRICA O LESIONES A
PERSONAS, CUMPLA CON LOS SIGUIENTES PUNTOS:
A. El trabajo de instalación y el cableado eléctrico
deben ser realizados por una persona(s) calificada de
acuerdo con todos los códigos y estándares aplicables,
incluyendo construcciones resistentes al fuego.
B. Es necesario contar con suficiente cantidad de aire
para una combustión y salida de gases adecuadas
a través del conducto (chimenea) del equipo de
consumo de combustible, a fin de evitar ráfagas de
aire. Siga las pautas del fabricante del equipo de
calefacción y los estándares de seguridad, tales como
aquellos publicados por la Asociación Nacional de
Protección contra Incendios (National Fire Protection
Association, NFPA), la Sociedad Estadounidense
para la Calefacción (American Society for Heating),
los Ingenieros de Refrigeración y Acondicionadores
de Aire (Refrigeration and Air Conditioning Engineers,
ASHRAE) y las autoridades de los códigos locales.
C. Al cortar o perforar una pared o un cielorraso, no dañe
el cableado eléctrico y de otros servicios ocultos.
D. Los ventiladores con conducto siempre deben contar
con ventilación hacia el exterior.
E. Desconecte el disyuntor de habitaciones adyacentes
mientras esté trabajando.
INSTRUCCIONES DE INSTALACIÓN
Instrucciones
de instalación
ADVERTENCIA
A FIN DE REDUCIR EL RIESGO
DE INCENDIOS, USE SÓLO CONDUCTOS DE METAL.
ADVERTENCIA
PARA SU SEGURIDAD
ADVERTENCIA
Desconecte toda la corriente
eléctrica del disyuntor principal o de la caja de fusibles
antes de la instalación.
Antes de comenzar la
instalación, desconecte la energía del panel de servicio
y bloquee los medios de desconexión para evitar el
accionamiento de la energía de manera accidental.
Cuando los medios de desconexión de servicio no
pueden bloquearse, coloque sobre el panel de servicio un
dispositivo de advertencia bien visible, como una etiqueta.
49-80813-2
9
PREPARACIÓN PARA LA INSTALACIÓN
Preparación para la instalación
DIMENSIONES DEL PRODUCTO
ESPACIOS PARA LA INSTALACIÓN
Esta campana de ventilación deberá ser instalada entre
el mínimo requerido de 24” y el máximo recomendado de
36” sobre la superficie de cocción.
Ŷ Siempre consulte las instrucciones de instalación
de la estufa o cocina en relación a los espacios
específicos del producto.
6-15/16"
El diseño varía de acuerdo
al modelo
11-1/2"
12"
3-1/8"
1-15/16"
NOTA:La altura de instalación debe medirse desde
la superficie de cocción hasta el lado inferior del la
superficie del gabinete
NOTA: UL requiere que cualquier superficie combustible
se halle a un mínimo de 30" sobre la superficie de
cocción. Las superficies combustibles inferiores podrán
estar cubiertas para cumplir con los requisitos.
Ŷ/DDOWXUDLQWHUQDGHOJDELQHWHHVWiQGDUGHEHUiSRVHHU
un mínimo de 18 1/2” para la ventilación vertical, y un
mínimo de 29” para la recirculación.
18" o 24"
9"
Ŷ(VWDFDPSDQDSXHGHFRQWDUFRQYHQWLODFLyQKDFLDHO
exterior, o puede ser instalada para un funcionamiento
con recirculación. Para un funcionamiento con
recirculación, consulte la Planificación de la Instalación
para Funcionamiento con Recirculación.
4-1/4"
Ŷ(VWDFDPSDQDSRGUiVHUPRQWDGDHQXQJDELQHWHGH
pared o ser instalada sobre una isla.
28-1/4" o
34-1/4"
19-1/8"
18-1/2" mín.
11-1/2"
PREPARACIÓN DEL GABINETE
24" mínimo requerido
36" máximo recomendado
VISTA
FRONTAL
18-1/2" mín.
Típicamente 36"
11-1/2"
1"
1"
NOTA: El conducto de salida de la campana está más
cerca de la parte trasera de la campana. Es importante
planificar la alineación sobre el punto de conexión de
la campana.
VISTA
LATERAL
29" mín.
6-1/2"
11-1/2"
3"
10
1"
49-80813-2
HERRAMIENTAS Y MATERIALES REQUERIDOS (NO SUMINISTRADOS)
Cinta aislante
de aluminio
Alicates de punta larga
Lápiz y cinta métrica
Perforadora eléctrica y
brocas correspondientes
Escalera de mano
Nivel
Gafas de seguridad
Conductos de 8"
y tapas según sea
necesario
Linterna
Alicate
pelacables
Tijeras para
hojalata
Tapones de alambre
aprobados por UL
Destornilladores de estrella y
de lados planos
PIEZAS PROVISTAS
Alivio de tensión para
la caja de conexiones
Guantes
PLAN DE INSTALACIÓN
Ubique las piezas empacadas con la campana.
NOTA: Es posible que la valija de herramientas contenga
piezas adicionales para realizar una serie de métodos de
instalación para diferentes modelos.
PRECAUCIÓN
A fin de reducir riesgos de
incendios y para que el aire salga de forma apropiada,
asegúrese de que el aire sea conducido hacia fuera - No
ventile el aire de la salida hacia espacios dentro de paredes
o cielorrasos o áticos, espacios muy bajos o garajes.
PREPARACIÓN PARA LA INSTALACIÓN
Preparación para la instalación
ADVERTENCIA
! RIESGO DE LESIONES PERSONALES
Valija de
Herramientas
Es recomendable que la campana extractora sea
instalada por 2 personas. Si la campana no es elevada
de forma correcta, se podrán producir daños sobre el
producto o lesiones personales.
Campana
A
NOTA: Esta campana puede ser instalada con conducto
o con recirculación. En una aplicación con conducto,
esta campana puede ser ventilada a través de la pared
o del cielorraso. Al ser instalada por recirculación, la
campana ventila hacia afuera los costados de la cubierta
del conducto.
B
Tornillos de Madera
con Cabeza Phillips
3/16" x 1-1/2" (QTY: 4)
Ensamble del
Regulador
49-80813-2
Tornillos para Máquina
con Cabeza Phillips
1/8" X 3/8" (QTY: 16)
D
L
Tornillos de Madera
con Cabeza Phillips
1/8" X 3/8" (QTY: 4)
Tornillos de
Madera con
Cabeza Phillips
3/16" x 1"
(QTY: 8)
QUITE EL ENVOLTORIO
PRECAUCIÓN
Se guantes para protegerse de
los bordes afilados.
Ŷ Quite la bolsa de piezas, el paquete de instrucciones y
otras piezas en cajas.
Ŷ Quite y descarte adecuadamente el envoltorio plástico
de protección y otros materiales de empaque.
11
PREPARACIÓN PARA LA INSTALACIÓN
Preparación para la instalación
PLANIFICACIÓN PREVIA
PLANIFICACIÓN PREVIA (CONT.)
Planificación para la Instalación con Conducto
Planificación de la Estructura del Gabinete Estándar
ŶEsta campana está diseñada para ventilarse en forma
vertical a través del cielorraso. Use un conducto circular
de 8”. Utilice codos suministrados en forma local para
ventilación horizontal a través de la pared trasera.
Ŷ El techo o gabinete estándar debe contar un con
agujero rectangular para ubicar por sí sola la inserción
de la campana estándar, o con el cobertor. Este
agujero es del mismo tamaño tanto para una instalación
de pared como de una isla. Asegure el paralelismo y
la nivelación del gabinete, de modo que no afecte la
nivelación de la campana con el gabinete.
Ŷ8VHWXEHUtDVPHWiOLFDV~QLFDPHQWH
ŶDetermine la ubicación exacta de la campana
de ventilación.
El frente del
agujero debe
tener un mínimo
de 3" desde
el frente del
gabinete
ŶPlanifique el recorrido de la salida de ventilación hacia
el exterior. A fin de maximizar el rendimiento de la
ventilación del sistema de ventilación:
1. Minimice la longitud del conducto y el número de
transiciones y codos.
Profundidad
La parte trasera
del agujero debe
tener un mínimo
de 1" desde la
pared trasera
2. Mantenga un tamaño de conducto constante.
3. Selle todas las juntas con cinta para conductos a fin
de evitar pérdidas.
NOTA: No se recomienda una ventilación flexible. La
ventilación flexible crea una presión trasera y turbulencia
del aire que reduce el rendimiento significativamente.
Ŷ Longitud máxima equivalente del conducto para 100
CFM: 150 pies para campanas de ventilación.
ŶInstale una tapa de pared o una tapa de techo con
regulador en la abertura externa. Solicite por adelantado
la cubierta de pared o el casquete de techo y cualquier
transición o longitud de conducto necesarios.
ŶCuando corresponda, instale un sistema de reposición
(reemplazo) de aire de acuerdo con los requisitos del
código local de construcción. Para acceder a soluciones
de aire disponibles, visite GEAppliances.com.
Ancho
UVC9300
UVC9360
Ancho (pulg.)
28-1/4
34-1/4
Profundidad (pulg.)
19-1/8
19-1/8
PLANIFICACIÓN DE INSTALACIÓN CON
RECIRCULACIÓN
Esta campana podrá ser instalada en el modo de
recirculación. El filtro de carbón es necesario para la
instalación con recirculación y está incluido con la unidad.
El sistema de ventilación puede desembocar a través
del techo o de la pared. Para ventilar a través de una
pared, es necesario un codo de 90° que se encuentre
instalado inmediatamente sobre la campana.
Tapa del Techo
Agregue Aislante
y/o Sellador
Gabinete
Agregue cinta a
la junta
Campana
Conducto Redondo
Tapa de
Pared
Agregue Aislante
y/o Sellador
Marco de Pared y Cielo Raso para un Soporte Adecuado
Esta campana de ventilación es pesada y la estructura
del gabinete necesita soportar el peso de la carcasa
de inserción cargada. Se deberá proveer un soporte
estructural adecuado en todos los tipos de instalación.
Ŷ/DLQVWDODFLyQVHUiPiVIiFLOVLODFDPSDQDGH
ventilación es instalada antes que la superficie
de cocción.
12
49-80813-2
SUMINISTRO DE ENERGÍA
IMPORTANTE – (Tenga a bien leer cuidadosamente)
ADVERTENCIA
PARA SEGURIDAD PERSONAL, ESTE APARATO DEBE
CONECTARSE A TIERRA DE MANERA ADECUADA.
Quite el fusible o abra el interruptor de circuitos antes de
comenzar la instalación.
No utilice un cable de extensión o un enchufe adaptador
con este artefacto. Siga los Códigos Eléctricos
Nacionales o códigos y ordenanzas locales vigentes.
Suministro eléctrico
Estas campanas de ventilación deben contar con un
suministro de 120V, 60Hz, deben estar conectadas a un
circuito derivado individual con una adecuada conexión a
tierra y deben contar con la protección de un interruptor
de circuitos o un fusible con retraso de 15 o 20 amperios.
Ŷ El cableado debe ser de 2 hilos con conexión a tierra.
Ŷ Si el suministro eléctrico no cumple con los requisitos
anteriores, llame a un electricista con licencia antes de
continuar.
Ŷ Dirija el cableado doméstico lo más cerca posible a
la ubicación de la instalación, en el cielorraso o pared
trasera. Ver página 14 para más detalles.
Ŷ Conecte el cableado al cableado doméstico en
cumplimiento con los códigos locales.
Instrucciones de conexión a tierra
El conductor a tierra debe conectarse a un metal con
conexión a tierra, un sistema de cableado permanente
o una terminal o conductor de conexión a tierra del
equipamiento en la campana.
PREPARACIÓN PARA LA
INSTALACIÓN DEL GABINETE
NOTA: Este soporte deberá ser retirado antes de
la instalación. Retire los 2 tornillos traseros y los 2
inferiores, de acuerdo con la siguiente ilustración.
1. De forma segura, presione el regulador ubicado en la
parte superior de la abertura del extractor. Controle que
el regulador se abra libremente. Adhiera el regulador a
la campana, usando los tornillos (B) provistos.
PREPARACIÓN PARA LA INSTALACIÓN
Preparación para la instalación
ADVERTENCIA
Una conexión inadecuada del
conductor de conexión a tierra del equipamiento puede
provocar un riesgo de descarga eléctrica. Consulte a un
electricista calificado o representante de servicio técnico si
tiene dudas sobre la correcta conexión a tierra del artefacto.
PREPARACIÓN DEL CABLEADO
ELÉCTRICO HOGAREÑO
El gabinete estándar deberá permitir que quede espacio
para el cableado hogareño, a fin de llegar a la caja
de empalmes ubicada en el siguiente diagrama. Si la
unidad es instalada sobre una isla, el cableado deberá
llegar desde el cielorraso. Si es necesario un cable de
corriente, el accesorio está disponible.
18" o 24"
Área
Eléctrica
9-1/2"
5-3/4"
o
8-3/4"
49-80813-2
2. La campana debe estar centrada de izquierda a
derecha sobre la superficie de cocción.
3. Retire y descarte de forma adecuada el envoltorio
plástico protector de la campana.
4. La superficie trasera de la campana debe estar a un
mínimo de 1” desde la pared trasera. La superficie
frontal de la campana debe estar a un mínimo de 3”
desde el panel del gabinete estándar frontal.
5. El gabinete estándar deberá permitir el retiro de
los paneles, a fin de brindar acceso al cableado
eléctrico y al conducto y sus conexiones a la
campana en caso de que sea necesario realizar el
servicio técnico o por otras razones.
13
INSTALACIÓN
Instalación
STEP 1 INSTALACIÓN DE LA
CAMPANA
CONEXIÓN ELÉCTRICA
1. Retire la tapa de la caja de empalmes eléctricos.
1. Confirme que el regulador esté en su posición en la
abertura de la salida de la campana, para acceder a
instrucciones, consulte la página anterior.
2. Inserte la campana en la abertura del gabinete.
2. Retire el tablero de la caja eléctrica.
Tablero de la
Caja Eléctrica con
Amortiguador de
Refuerzo
3. Alimente el Cable de Suministro Eléctrico a través del
agujero y asegure el mismo con un amortiguador de
refuerzo.
4. Adhiera el cable blanco del suministro de corriente
3. Ajuste con 8 tornillos [(A) (L) o (D) según sea
necesario), 4 en el frente y 2 a cada lado, hacia
la parte trasera de la campana. Un resorte está
bloqueando el perno a cada lado de la campana, el
cual ayuda a sostener la unidad mientras los tornillos
son instalados.
NOTA: No se aleje de la campana mientras la
campana está siendo sostenida sólo por los pernos.
(A) al cable blanco de la campana extractora (D)
con una tuerca para cable. Adhiera el cable negro
del suministro de corriente (B) al cable negro de la
campana extractora (C) con una tuerca para cable.
Conecte el cable a tierra verde (E) (verde y amarillo)
debajo del tornillo de conexión a tierra verde.
E
A
Cableado
Hogareño
B
D
C
Cableado de
la Campana
5. Vuelva a colocar la tapa de la caja de empalmes
eléctricos.
4. Una vez ubicada la campana, selle el conducto de la
campana con cinta para conductos
(No use tornillos).
14
49-80813-2
STEP 2 OPCIÓN DE RECIRCULACIÓN (PIEZAS SUMINISTRADAS LOCALEMENTE)
1. Haga un agujero en el sofito para el conducto de salida.
2. Instale la parrilla de ventilación sobre el conducto de salida.
3. Selle las uniones del conducto con cinta para conductos.
Para ordenar el kit de recirculación opcional, visite GEAppliances.com.
Línea central
de la campana
Corte del Sofito
INSTALACIÓN
Instalación
6-15/16"
Bota en Ángulo
de 90º
11-1/2"
Conducto de 8”
Filtros
STEP 3 FINALICE LA INSTALACIÓN
1. Inserte los filtros; consulte la sección de Filtros.
2. Controle el funcionamiento de las luces y del
calefactor.
3. Finalice los gabinetes estándares.
49-80813-2
15
INSTALACIÓN
Instalación
TECNOLOGÍA DE REPOSICIÓN DE AIRE
Nota para los Instaladores e Inspectores: Este producto está equipado con una función de instalación simple que limita
los niveles máximos de CFM, a fin de cumplir con ciertos códigos o regulaciones locales. Es posible que este método de
instalación no sea necesario en todas las instalaciones; para acceder a más pautas, por favor consulte sus códigos locales.
PRECAUCIÓN
La campana deberá ser desconectada de la alimentación de corriente principal siguiendo
las instrucciones de conversión que figuran a continuación. Si no se siguen estos pasos, se podrán producir lesiones
personales o daños sobre el producto.
A fin de modificar la unidad (si es necesario para
cumplir con los códigos locales):
390CFM o 290CFM
Por diseño, la velocidad máxima del calefactor es superior a
los 400 CFM. Si los códigos locales requieren una reducción
de los CFM, modifique el cableado como se describe a
continuación:
1. Retire los deflectores; consulte la sección de Filtros.
2. Retire la tapa de la caja del tablero de control.
3. Ubique el arnés del motor enchufado al tablero de
control.
4. A - Para un máximo de 390 CFM, la unidad puede
funcionar en 4 velocidades (Baja, Media, Alta,
Aumentada).
Tapa de la Caja del Tablero de Control
1. Desconecte el conector del cable azul del cable
rojo.
2. Conecte los 2 cables rojos juntos.
3. Desconecte el conector azul no utilizado y ondule
el extremo si así lo desea.
B - Para un máximo de 290 CFM, la unidad puede
funcionar en 3 velocidades (Baja, Media, Alta).
1. Desconecte el conector del cable azul del cable
rojo.
Conector del Arnés del Motor
2. Desconecte el conector azul no utilizado y ondule
el extremo si así lo desea.
5. Vuelva a adherir la tapa de la caja del tablero de control
e instale los deflectores.
Nota para los Inspectores: A fin de verificar que este
producto fue instalado en una de estas configuraciones,
controle las conexiones del cableado del motor de acuerdo
con la descripción previa.
Red
Blue
Red
Arnés del Motor
16
49-80813-2
¡Ahorre tiempo y dinero! Primero revise los cuadros que aparecen en las siguientes páginas y es posible que no
necesite solicitar reparaciones.
Problema
Causas posibles
Qué hacer
El Ventilador/ la Luz no
funciona cuando el botón
está en ON (Encendido)
El fusible puede haberse quemado o
el interruptor decircuitos puede haber
saltado.
Cambie los fusibles o reconfigure el interruptor de
circuitos.
Ruido de flujo de aire muy
elevado o anormal
Tamaño de conducto incorrecto
utilizado en la instalación.
Esta campana requiere un conducto de 8” para
funcionar de manera óptima. El uso de un conducto
más pequeño hará que la ventilación se reduzca.
Minimice la longitud del conducto y el número de
transiciones y codos. Los técnicos de GE Appliances
no pueden corregir este problema si hay una
instalación inadecuada.
El ventilador no hace
circular aire o desplaza
desplaza el aire más
despacio que lo normal y/o
hace ruido de flujo de aire
elevado o anormal
Obstrucciones en el conducto.
Verifique que no haya obstrucciones en la ventilación.
Controle que la cubierta de pared o casquete de
techo tengan una hoja o puerta.
La hoja del regulador de tiro de la
cubierta de pared o casquete de
techo puede estar cerrada.
Asegúrese de que el regulador de tiro se mueva
libremente. Las hojas del regulador de tiro pueden
darse vuelta y no se abrirán por completo cuando
esto suceda. Ajústela con la posición original.
El filtro de grasa metálico y el filtro
de carbón (si lo hubiera) pueden
estar sucios.
Limpie el filtro de grasa metálico y vuelva a colocar el
filtro de carbón (si lo hubiera). Ver Cuidado y limpieza
de la campana de ventilación.
Insuficiente reposición (reemplazo)
de aire
Se requiere suficiente reposición (reemplazo) de aire
para que los artefactos con salida de aire funcionen
de acuerdo con sus calificaciones energéticas.
Controle los códigos locales de construcción, que
podrán requerir o aconsejar enfáticamente el uso de
reposición de aire. Para acceder soluciones de aire
disponibles, visite GEAppliances.com.
Falla temprana de la
lámpara
El voltaje de la lámpara es
demasiado alto.
Reemplace la misma por una con el voltaje correcto.
El ventilador se enciende
automáticamente y no
puede ser apagado.
Esto es normal.
La función del sensor encenderá el ventilador de
forma automática si la temperatura de cocción se
eleva demasiado. El ventilador luego se apagará
cuando las temperaturas desciendan a un nivel
apropiado.
El ventilador continúa
encendiéndose y
apagándose.
Es posible que el motor se esté
sobrecalentando y apagando solo.
Esto puede ser nocivo para el motor.
Asegúrese de que los filtros estén limpios. Si el ciclo
de encendido y apagado continúa, comuníquese al
servicio técnico.
Las luces no funcionan
Se usaron lámparas incorrectas. Se
deberán usar lámparas regulables
que sean compatibles con GU10.
Para solicitar lámparas de reemplazo, visite
GEAppliances.com.
No quedó grasa capturada
en las bandejas de goteo
No quedó grasa capturada en las
bandejas de goteo.
Instale los deflectores de forma adecuada
asegurándose de que la flechas a ambos lados de
los mismos estén apuntando hacia el frente de la
unidad, de modo que las aberturas para la grasa en
la parte inferior de los deflectores sean insertadas en
las bandejas de goteo; consulte la sección de Filtros.
La campana no funciona de
forma remota
Problemas en el enrutador, no hay
señal inalámbrica, etc.
Para solicitar asistencia para la conectividad de la red
inalámbrica de la campana, por favor comuníquese al
800.220.6899.
La campana no se encuentra
conectada.
49-80813-2
CONSEJOS PARA LA SOLUCIÓN DE PROBLEMAS
Consejos para la Solución de Problemas... Antes de solicitar el servicio técnico
17
GARANTÍA LIMITADA
Garantía Limitada de la Cocina Eléctrica de GE Appliances
GEAppliances.com
Todo el servicio de garantía es provisto por nuestros Centros de Servicio de Fabricación, o un técnico autorizado de Customer Care®.
Para programar una visita del servicio técnico a través de Internet, visítenos en geappliances.com/service_and_support/, o llame al
800.GE.CARES (800.432.2737). Cuando llame para solicitar el servicio, tenga los números de serie y modelo disponibles.
Para realizar el servicio técnico de su electrodoméstico, se podrá requerir el uso de datos del puerto de abordaje para su diagnóstico.
Esto da al técnico del servicio de fábrica de GE Appliances la habilidad de diagnosticar de forma rápida cualquier problema con
su electrodoméstico, y de ayudar a GE Appliances a mejorar sus productos al brindarle a GE Appliances la información sobre su
electrodoméstico. Si no desea que los datos de su electrodoméstico sean enviados a GE Appliances, solicitamos que le indique a su
técnico no entregar los datos a GE Appliances en el momento del servicio.
Por el Período de
GE Appliances reemplazará
Un Año
Desde la fecha de la
compra original
Cualquier pieza del producto de cocción que falle debido a un defecto en los materiales o la
fabricación. Durante esta garantía limitada de un año, GE Appliances también proveerá, sin costo,
todo el trabajo y costos del servicio relacionados con el reemplazo de la pieza defectuosa.
Qué no cubrirá GE Appliances:
Ŷ Viajes del técnico del servicio a su hogar para enseñarle
sobre cómo usar el producto.
Ŷ ,QVWDODFLyQHQWUHJDRPDQWHQLPLHQWRLQDGHFXDGRV
Ŷ )DOODVGHOSURGXFWRHQFDVRGHDEXVRPDOXVRPRGLILFDFLyQ
o uso para propósitos diferentes al original o uso comercial.
Ŷ 5HHPSOD]RGHIXVLEOHVGHODFDVDRUHLQLFLRGHGLV\XQWRUHV
Ŷ 'DxRVRFDVLRQDGRVVREUHHOSURGXFWRSRUDFFLGHQWH
incendio, inundaciones o catástrofes naturales.
Ŷ 'DxRVLQFLGHQWDOHVRFRQVHFXHQWHVFDXVDGRVSRUSRVLEOHV
defectos sobre este producto.
Ŷ 'DxRVVREUHHODFDEDGRWDOHVFRPRy[LGRVREUHOD
superficie, deslustres o manchas pequeñas no informadas
dentro de las 48 horas luego de la entrega.
Ŷ 'DxRFDXVDGRGHVSXpVGHODHQWUHJD
Ŷ 3URGXFWRQRDFFHVLEOHSDUDEULQGDUHOVHUYLFLRUHTXHULGR
Ŷ 0DUFDVRPDQFKDV LQFOX\HQGRPDQFKDVGHy[LGRVREUH
la superficie) que pueden ser eliminadas siguiendo las
instrucciones de limpieza.
Ŷ 6ROLFLWHHOVHUYLFLRWpFQLFRSDUDUHSDUDURUHHPSOD]DUODV
lámparas, excepto las lámparas LED.
EXCLUSIÓN DE GARANTÍAS IMPLÍCITAS
Abroche su recibo aquí. Para acceder al servicio técnico de acuerdo con
la garantía deberá contar con la prueba de la fecha original de compra.
Su única y exclusiva alternativa es la reparación del producto, como se indica en la Garantía Limitada. Las
garantías implícitas, incluyendo garantías implícitas de comerciabilidad o conveniencia sobre un propósito
particular, se limitan a un año o al período más corto permitido por la ley.
18
Esta garantía limitada se extiende al comprador original y a cualquier dueño subsiguiente de productos comprados
para uso hogareño dentro de EE.UU. Si el producto está en un área donde no se encuentra disponible un Proveedor
Autorizado del Servicio Técnico de GE Appliances, usted será responsable por el costo de un viaje o se podrá
requerir que traiga el producto a una ubicación del Servicio Técnico de GE Appliances autorizado para recibir el
servicio. En Alaska, la garantía limitada excluye el costo de envío o llamadas del servicio a su hogar. Algunos estados
no permiten la exclusión o limitación de daños fortuitos o consecuentes. Esta garantía limitada le da derechos legales
específicos y es posible que tenga otros derechos legales que varían entre un estado y otro. Para conocer cuáles son
sus derechos legales, consulte a la oficina de asuntos del consumidor local o estatal o al Fiscal de su estado.
Garante: GE Appliances, a Haier company
Louisville, KY 40225
Garantías Extendidas: Adquiera una garantía extendida de GE Appliances y conozca los descuentos especiales que
están disponibles mientras su garantía aún está vigente. Puede acceder a la misma a través de Internet en cualquier
momento en
geappliances.com/service_and_support/shop-for-extended-service-plans.htm
o llamando al 800.626.2224 durante el horario comercial. Los Servicios para los GE Appliances aún estarán
disponibles cuando su garantía caduque.
49-80813-2
¿Busca Algo Más?
GE Appliances ofrece una variedad de accesorios para
mejorar sus experiencias de cocción y mantenimiento!
Para acceder a números telefónicos e información de sitios
Web, consulte la página de Soporte para el Consumidor.
Estos y otros productos están disponibles:
Piezas
ACCESORIOS
Accesorios
Kit del Cable de Corriente
Kit de Aire de Reposición
Filtro de Carbón
Kit de Recirculación
Control Remoto
Suministros de Limpieza
Limpiadores de Acero Inoxidable CERAMA BRYTE®
Limpiador para Electrodomésticos de Acero Inoxidable CERAMA BRYTE®
Bar Keepers Friend Soft Cleanser™
49-80813-2
19
SOPORTE PARA EL CONSUMIDOR
Soporte para el Consumidor
Sitio Web de GE Appliances
¿Desea realizar una consulta o necesita ayuda con su electrodoméstico? ¡Intente a través del Sitio Web de GE Appliances las
24 horas del día, cualquier día del año! Usted también puede comprar más electrodomésticos maravillosos de GE Appliances y
aprovechar todos nuestros servicios de soporte a través de Internet, diseñados para su conveniencia.
En EE.UU.: GEAppliances.com
Registre su Electrodoméstico
¡Registre su electrodoméstico nuevo a través de Internet, según su conveniencia! Un registro puntual de su producto permitirá
una mejor comunicación y un servicio más puntual de acuerdo con los términos de su garantía, en caso de surgir la necesidad.
También puede enviar una carta en la tarjeta de inscripción preimpresa que se incluye con el material embalado.
En EE.UU.: GEAppliances.com/register
Servicio Programado
El servicio de reparación de expertos de GE Appliances está a sólo un paso de su puerta. Conéctese a través de Internet y programe
su servicio a su conveniencia cualquier día del año. En EE.UU.: GEAppliances.com/service
o comuníquese al 800.432.2737 durante el horario de atención comercial.
Garantías Extendidas
Adquiera una garantía extendida de GE Appliances y conozca los descuentos especiales que están disponibles mientras su
garantía aún está vigente. La puede adquirir en cualquier momento a través de Internet. Los servicios de GE Appliances aún
estarán allí cuando su garantía caduque.
En EE.UU.: GEAppliances.com/extended-warranty
o comuníquese al 800.626.2224 durante el horario de atención comercial.
Conectividad Remota
Para solicitar asistencia para la conectividad de red inalámbrica (para modelos con acceso remoto),
visite nuestro sitio web en GEAppliances.com/connected-home-smart-appliances/ o comuníquese al 800.220.6899 en EE.UU.
Piezas y Accesorios
Aquellos individuos calificados para realizar el servicio técnico de sus propios electrodomésticos podrán solicitar el envío de
piezas o accesorios directamente a sus hogares (se aceptan las tarjetas VISA, MasterCard y Discover). Ordene hoy a través de
Internet durante las 24 horas, todos los días. En EE.UU.: GEApplianceparts.com o de forma telefónica al 877.959.8688 durante
el horario de atención comercial.
Las instrucciones que figuran en este manual cubren los procedimientos que serán realizados por cualquier usuario.
Otros servicios técnicos generalmente deben ser derivados a personal calificado del servicio. Se deberá tener cuidado,
ya que una reparación indebida podrá hacer que el funcionamiento no sea seguro.
Contáctenos
Si no se encuentra satisfecho con el servicio que recibió de GE Appliances, comuníquese con nosotros a través de nuestro sitio
Web con todos los detalles, incluyendo su número telefónico, o escriba a:
En EE.UU.: General Manager, Customer Relations | GE Appliances, Appliance Park | Louisville, KY 40225
GEAppliances.com/contact
Impreso en China
20
49-80813-2

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement