XO XOI27S User manual

XO XOI27S User manual
XOI27S
NEED HELP?
Call our ventilation experts toll free al 800-966-8300
AVEZ-VOUS BESOIN D’AIDE ?
Contactez nos experts au numéro gratuit 800-966-8300
¿NECESITA AYUDA?
Póngase en contacto con nuestros expertos a través del número gratis 800-966-8300
USA RANGE HOOD - User instructions
F
HOTTE DE CUISINE - Notice d’utilisation
E
CAMPANA EXTRACTORA - Manual de utilización
XO Hood Warranty
Proof of original purchase date and invoice is needed to obtain
service under warranty.
What is covered
Limited 2 Year Warranty.
For 2 years from the original date of purchase, we will provide,
free of charge, parts and service labor in your home to repair or
replace any part of the hood that fails because of a manufacturing defect.
The warranty is extended to the original purchaser for products
purchased for ordinary home use in North America.
Should you require service for your XO product call a product
service specialist at 800.966.8300
What is not covered
Improper Installation.
Service trips to the home to teach you how to use the product.
Resetting circuit breakers.
Damage caused after delivery.
EXPECT MORE FROM XO
When buying any XO appliance
you can be confident
you have purchased a high quality,
innovative, and stylish product,
from a company who cares about you
ENGLISH
USA
IMPORTANT SAFETY INSTRUCTIONS
FOR RESIDENTIAL USE ONLY
READ AND SAVE THESE INSTRUCTIONS
PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING.
IMPORTANT: Save these Instructions for the Local Electrical Inspectors use.
INSTALLER: Please leave these Instructions with this unit for the owner.
OWNER: Please retain these instructions for future reference.
Take care when using cleaning agents or detergents.
Suitable for use in household cooking area
WARNING - To reduce the risk of fire or electric shock, do not use this fan with any
Solid-State Speed Control Device.
CAUTION - To reduce risk of fire and to properly exhaust air, be sure to duct air
outside – Do not vent exhaust air into spaces within walls or ceilings or into attics,
crawl spaces, or garages.
CAUTION - For general ventilating use only. Do not use to exhaust hazardous or
explosive materials and vapors.
CAUTION - To avoid motor bearing damage and noisy and/or unbalanced impellers,
keep drywall spray, construction dust, etc. off power unit.
CAUTION - Please read specification label on product for further information and
requirements.
WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
A. Use this unit only in the manner intended by the manufacturer. If you have questions,
contact the manufacturer.
B. Before servicing or cleaning unit, switch power off at service panel and lock the
service disconnecting means to prevent power from being switched on accidentally.
When the service disconnecting means cannot be locked, securely fasten a prominent
warning device, such as a tag, to the service panel.
WARNING - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
A. Never leave surface units unattended at high settings. Boilovers cause smoking
and greasy spillovers that may ignite. Heat oils slowly on low or medium settings.
B. Always turn hood ON when cooking at high heat or when flambeing foods ( i.e.
-3-
Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambè ).
C. Clean ventilating fans frequently. Grease should not be allowed to accumulate on
fan or filter.
D. Use proper pan size. Always use cookware appropriate for the size of the surface
element.
E. Keep fan, filters and grease laden surface clean.
F. Use high range setting on range only when necessary.Heat oil slowly on low to
medium setting.
G. Don’ t leave range unattended when cooking.
H. Always use cookware and utensils appropriate for the type and amount off food
being prepared.
WARNING – TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE
TOP GREASE FIRE, OBSERVE THE FOLLOWINGa:
A. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off
the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately,
EVACUATE AND CALL THE FIRE DEPARTMENT.
B. NEVER PICK UP A FLAMING PAN – You may be burned.
C. DO NOT USE WATER, including wet dishcloths or towels – a violent steam explosion
will result.
D. Use an extinguisher ONLY if:
1. You know you have a Class ABC extinguisher, and you already know how to operate it.
2. The fire is small and contained in the area where it started.
3. The fire department is being called.
4. You can fight the fire with your back to an exit.
aBased on “kitchen firesafety tips” published by NFPA
Proper maintenance of the Range Hood will assure proper performance of the
unit.
INSTALLATION INSTRUCTIONS
A.
B.
C.
D.
WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
Installation work and electrical wiring must be done by qualified person(s) in accord
ance with all applicable codes and standards, including fire-rated construction.
Sufficient air is needed for proper combustion and exhausting of gases through the
flue (chimney) of fuel burning equipment to prevent back drafting. Follow the
heating equipment manufacturer’s guideline and safety standards such as those
published by the National Fire Protection Association (NFPA), and the American
Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and
the local code authorities.
When cutting or drilling into wall or ceiling, do not damage electrical wiring and
other hidden utilities.
Ducted fans must always be vented to the outdoors.
-4-
E. This unit must be grounded.
WARNING - TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.
WARNING - UNDER CERTAIN CIRCUMSTANCES DOMESTIC APPLIANCES MAY BE
DANGEROUS.
A. Do not check filters with hood working.
B. Do not touch the lamps after a prolonged use of the appliance.
C. No food must be cooked flambè underneath the hood.
D. The use of an unprotected flame is dangerous for the filters and could cause fires.
E. Watch constantly the fried food in order to avoid the cooking oil flares up.
F. Before performing any mainteinance operation, disconnect the hood from the
electrical service.
The manufacturers will not to accept any responsability for eventual damages, because
of failure to observe the above instructions.
-5-
Installation Preparation
DUCT FITTINGS:
This Hood Must Use an
6" Round Duct. It Can
Transition to 3-1/4" x
10" or 3-1/4" x 12" Duct.
Use this chart to compute maximum permissible
lengths for duct runs to
outdoors.
NOTE: Do not exceed maximum permissible equivalent
lengths!
Maximum duct length:
100 feet for range hoods.
Flexible ducting:
If flexible metal ducting
is used, all the equivalent
feet values in the table
should be doubled. The
flexible metal duct should
be straight and smooth
and extended as much as
possible.
DO NOT use flexible plastic
ducting.
NOTE: Any home ventilation
system, such as a ventilation
hood, may interrupt the
proper flow of combustion
air and exhaust required
by fireplaces, gas furnaces,
gas water heaters and other
naturally vented systems. To
minimize the chance of interruption of such naturally
vented systems, follow the
heating equipment manufacturer’s guidelines and
safety standards such as
those published by NFPA.
Duct
Piece:
Equivalent
Dimensions: Number
Length*:
Quantity
Used:
Total
Equivalent
Length:
ft. (per foot
Round, straight 1
lenhgth)
3-1/4" x 10"
straight
1 ft. (per foot
lenhgth)
90° elbow
12 ft.
45° elbow
7 ft.
3-1/4" x 10"
3-1/4" x 12"
90° elbow
14 ft.
10 ft.
3-1/4" x 10"
3-1/4" x 12"
45° elbow
8 ft.
6 ft.
3-1/4" x 10"
3-1/4" x 12"
90° elbow
33 ft.
24 ft.
6" round to
rectangular
2 ft.
Rectangular to
8" round
2 ft.
3-1/4" x 10"
3-1/4" x 12"
6" round to
rectangular
transition 90°
elbow
4 ft.
4 ft.
3-1/4" x 10"
3-1/4" x 12"
Rectangular to
6" transition
90° elbow
4 ft.
4 ft.
Round wall
cap with
dramper
24 ft.
3-1/4" x 10"
3-1/4" x 12"
Rectangular
wall cap with
dramper
24 ft.
18 ft.
Round roof
cap
33 ft.
*Actual length of straight duct plus duct
fitting equivalent. Equivalent length of duct Total Duct Run =
pieces reflect requirements for good venting
performance with any ventilation hood.
-6-
NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces,
ceiling, attics or garages.
All exhaust must be ducted to the outside, unless using the recirculating option.
Use single wall rigid Metal ductwork only.
Fasten all connections with sheet metal screws and tape all joints w/ certified Silver
Tape or Duct Tape.
INSTALL THE DUCTWORK:
NOTE: To reduce the risk of fire, use only metal ductwork.
1. Decide where the ductwork will run between the hood and the outside.
2. A straight, short duct run will allow the hood to perform most efficiently.
3. Long duct runs, elbows, and transitions will reduce the performance of the
hood. Use as few of them as possible.
4. Install a roof or wall cap. Connect 6" round metal ductwork to cap and work
back towards hood location. Use duct tape to seal the joints between ductwork
sections.
-7-
Installation - Ducting Options
WARNING FIRE HAZARD
› Front of hood
› Side of hood
�����
�������
��������
�������
�������
��������
��������
��������
��������
���������
› Mounting height and
clearance:
��������
�������
› Top of hood
��
�
Hood Specifications
Product dimensions and clearance
XOI27S:
�����������������
���
-8-
Installation Instructions
Installation - Vented to the outside
1. Fixing the hood to the lower
part of the wall cabinet:
This type of appliance must be fitted inside
a cabinet or inside another type of support
structure. The overall measurements of the
range hood are given in figure 1-2. Before
proceeding with range hood installation,
remove grille D by pressing the two side
buttons A, as shown in figure 3.
Fix the appliance in place using 8 screws
(not supplied) which are suited to the
type of cabinet. To install the range hood
correctly, first fit the 4 screws A and then
the 4 screws B, in accordance with the
diagram in figure 4. After fixing the range
hood to the lower part of the cabinet,
place grille D (Fig.4) back in the correct
position. During this procedure, make
sure that grille D is fastened properly.
The appliance expels the fumes through
an outside wall or a duct. It is necessary to
buy a telescopic pipe in accordance with
the standards in use (inflammable) and
connect it to flange H (Fig.5).
���
�����
��
��
��
��
�
Fig.1
�������
��������
��������
��������
IMPORTANT - The range hood must
be secured to wall studs or use drywall
anchors capable of supporting 75 lbs.
�������
��������
�������
�����
��������
���������
Fig.2
-9-
�
�
Fig.3
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
Fig.4
�
Fig.5
- 10 -
POWER SUPPLY:
IMPORTANT – (Please read carefully)
WARNING:
FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED.
Remove house fuse or open circuit breaker before beginning installation. Do not use an
extension cord or adapter plug with this appliance. Follow National electrical codes or
prevailing local codes and ordinances.
Electrical supply:
These vent hoods must be supplied with 120V, 60Hz, and connected to an individual,
properly grounded branch circuit, and protected by a 15 or 20 amp circuit breaker or
time delay fuse.
• Wiring must be 2 wire with ground.
• If the electrical supply does not meet the above requirements, call a licensed
electrician before proceeding.
• Route house wiring as close to the installation location as possible, in the ceiling or
back wall. Refer to Wiring Locations on page 12.
• Connect the hood wiring to the house wiring in accordance with local codes.
Grounding instructions:
The grounding conductor must be connected to a grounded metal, permanent wiring
system, or an equipment-grounding terminal or lead on the hood.
WARNING: The improper connection of the equipment-grounding conductor
can result in a risk of electric shock. Check with a qualified electrician or service representative if you are in doubt whether the appliance is properly grounded.
- 11 -
2. CONNECT ELECTRICAL:
• Power Supply Connection:
For connection to the power supply refer
to the follows Fig.6:
BLACK = L line
WHITE = N neutral
GREEN / YELLOW = G ground
- A double-pole switch properly rated
must be installed to provide the range
hood power supply disconnection.
- Connect the electrical conduit to the
Field Wiring Compartment using listed
conduit fittings.
- Carry out the power supply connection
in accordance with the national electric
code, ANSI/NFPA 70-1999.
5. Insert the wires into the box, then close
the box cover, securing it using the
s c r e w s t h a t w e r e p r e v i o u s l y
removed.
The appliance should be installed at a
minimum height of 27" up to a maximum
height of 32" for optimal performance.
If a connection ductwork composed of
two parts is used, the upper part must
be placed outside the lower part. Do not
connect the range hood exhaust duct air
to the same duct air used to exhaust hot
air or fumes from other appliances other
than electrical.
• In the FILTERING version it is necessary to apply a metal air exhaust tube M
(Fig.7), with a minimum length of 15",
connected to the flange of the collector.
It must be positioned vertically and fastened to a specific opening made on the
top part of the cabinet.
��������
Fig.6
�
Fig.7
3. CONNECT THE DUCTWORK:
�����������������
���
- 12 -
DUCTLESS RECIRCULATING OPTION:
�
�
�
Carbon filter kit XORFK04: The kit includes an air diverter A, 2 screws and 2 expansions plugs B and 2 round filters C. To convert this model from the sunction to the filtering version, it is not necessary to use the air deviator A and the screws B.
�
�
Fig.1: Remove the aluminum panels by pulling the lever 1 out and pushing downwards 2.
- 13 -
�
Fig.2: The filters C must be applied to the suction unit inside the hood, centering them inside
of it and turning them 90° until they snap into place.
�
�
Fig.3: Put the aluminum panels back in place (Fig.1).
- 14 -
USE
• If the apparatus is equipped with the
following controls:
A = LIGHT
B = OFF
C = SPEED I
D = SPEED II
E = SPEED III
G = MOTOR WORKING indicator.
�
- 15 -
�
�
�
�
�
MAINTENANCE
• We recommend that the range hood is
switched on before any food is cooked.
We also recommend that the appliance
is left running for 15 minutes after the
food is cooked, in order to thoroughly
eliminate all contaminated air.
The effective performance of the range
hood depends on constant maintenance;
the anti-grease filter and the active carbon
filter both require special attention.
• The anti-grease filter is used to trap
any grease particles suspended in the
air, therefore is subject to saturation
(the time it takes for the filter to become
saturated depends on the way in which
the appliance is used). The grease filters
should be cleaned frequently. Use a
warm detergent solution. Grease filters
are a dishwasher safe.
- To prevent potential fire hazards, the
anti-grease filters should be washed a
�
minimum of every 2 months (it is possible
to use the dishwasher for this task).
- After a few washes, the colour of the
filters may change. This does not mean
they have to be replaced.
If the replacement and washing
Fig.8
instructions are not followed, the antigrease filters may present a fire hazard.
• The active carbon filters are used to
purify the air which is released back into the room. The filters are not washable or reusable and must be replaced at least once every four months. The active carbon filter
saturation level depends on the frequency with which the appliance is used, the type of
cooking performed and the regularity with which the anti-grease filters are cleaned.
• Clean the range hood frequently, both inside and outside, using a cloth which has
been dampened with denatured alcohol or neutral, non-abrasive liquid detergents.
• The light on the range hood is designed for use during cooking and not for general
room illumination. Extended use of the light reduces the average duration of the bulb.
• Hood Cleaning:
Stainless steel is one of the easiest materilas to keep clean. Occasional care will help
preserve its fine appearance.
Cleaning tips:
- Hot water with soap or detergent is all that is usually needed.
- Follow all cleaningby rising with clear water. Wipe dry with a clean, soft cloth to avoid
- 16 -
water marks.
- For discolorations or deposit that persist, use a non-scratching household cleanser or
stainless steel polishing powder with a little water and a soft cloth.
- For stubborn cases, use a plastic scouring pad or soft bristle brush together with cleaser
and water. Rub lightly in direction of polishing lines or “grain” of the stainless finish. Avoid
using too much pressure wich may mar the surface.
- DO NOT allow deposit to remain for long periods of time.
- DO NOT use ordinary steel wool or steel brushes. Small bits of steel may adhere to the
surface causing rust.
- DO NOT allow salt solutions, disinfectants, bleaches, or cleaning compounds to remain
in contact with stainless steel for extended periods. Many of these compounds contain
chemicals with may be harmful. Rinse with water after exposure and wipe dry with a clean
cloth.
Painted surfaces should be cleaned with warm water and mild detergent only.
• Replacing the aluminum panels:
To replace the aluminium panels, simply pull handle A as shown in Fig.8.
- 17 -
FUSE
• The halogen lamps circuit is controlled
by a fuse 5x20 mm, 125V 5A. In case of
necessity it can be replaced only by specialized personnel.
• Replacing halogen light bulbs:
To replace the halogen lamps B, from the
inside of the cooker hood press downwards
with two fingers as shown in Fig.9.
�
�
Fig.9
- 18 -
XOI27S:
���
���
���
���
��
���
���
���
���
��
���
��
���
���
��
- 19 -
��
���
OPTIONS AND ACCESSORIES:
Model XORFK04 Ductless Recirculating Filter Kit.
- 20 -
INSTALLATION PREPARATION:
Check installation hardware:
Locate the hardware package packed with the hood and check contents.
TYPE
DESCRIPTION
N°
A
1/8" x 1/2"
8
Aluminum filter
- 21 -
XOI Spec Sheet
Model: XOI27S
Sizes: 27-3/4" Depth: 11"
Features and Benefits:
- 600 CFM high velocity blower optimally removes
Smoke, Grease and Odors.
- 3 speed push button controls.
- Two 50W Halogen Lights - Provide brilliant
illumination over the cooking surface.
������
��
�
��������
- Aluminum Mesh Filters - Trap airborne smoke and
grease particles. They can be easily be removed
for dishwasher-safe cleaning.
�
�����
��������
������
- Unit Dimensions: 27-3/4" W x 11" D x 10" T
Cut Out Dims: 26-7/16" W x 10-1/16" D.
��
��
- Mounting Height from cooking surface 27”-32”.
��
��
��
������
Duct Options and Electrical Requirements:
- 6 inch duct required.
- Ductless Option for applications where no
ducting in available.
��
�
���
����
- AC 120v-60Hz (4.35amp).
Options:
- Optional recirculating kit if outside venting is
unavailable.
Model: XORFK04
XO is Exclusively Distributed by:
Eastern Marketing Corp 24 Eisenhower Parkway Roseland,
New Jersey 07068 800-966-8300
www.easternmarketingcorp.com
www.xoappliace.com
- 22 -
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement