Miele 52718663USA Installation Plan

Miele 52718663USA Installation Plan
Installation Plan
Tumble dryer
PT 7186 EL (Electrically Heated)
en - US
18.15
10 183 440 / 00
U.S.A.
Miele, Inc.
National Headquarters
9 Independence Way
Princeton, NJ 08540
Phone: 800-991-9380
609-419-4241
Fax:
www.mieleusa.com
Technical Service & Support
Nationwide
Phone: 800-991-9380
Fax:
800-220-1348
[email protected]
It is essential to read the operating and installation instructions before
installing, commissioning or using the machine.
This avoids the risk of accidents or damage.
All rights reserved
10 183 440 / 00
2
27 3/16
1 3/4
12
40 3/16
30 1/16
12
13 3/4
12
12
52 3/16
17 5/16
3/4
20 7/8
12
27 1/4
40 3/16
3/4
28 3/8
21 1/4
27 9/16
43 5/16
27 9/16
3/4
27 1/4
30 1/16
3/4
27 3/16
27 1/4
17 5/16
13 3/4
40 3/16
27 3/16
28 3/8
43 5/16
PT 7186 EL - measurements in inches
3
3 5/8
12
12
5 13/16
PT 7186 EL - measurements in inches
3 5/8
51 3/16
3 15/16
51 3/16
12
3 5/8
5 13/16
23 5/16
3 5/8
51 3/16
3 15/16
51 3/16
23 5/16
4
Option: Installation on Miele base (US)
22 1/16
27
10 13/16
12 1/4
24 5/8
17 5/16
13/16
43 5/16
24 3/4
27
27 1/8
43 1/4
27 1/4
21 5/8
2 13/16
3 15/16
26 7/8
27 1/4
17 3/8
12
12 5/8
13/16
39 3/8
40 3/16
Option: Installation on Miele base (UG/UO)
2 13/16
2
2 1/2
1 5/8
1/2
PT 7186 EL - measurements in inches
1/4
5
Standard installation
17 3/8
3/4
11 3/4
3/4
40 1/8
40 1/8
Option: Installation on concrete platform (BS)
21 5/8
3
39 3/8
21 5/8
2 3/4
4
27 1/8
10 7/8
4
10 7/8
3
27 1/4
43 1/4
22
27 1/2
43 1/4
27 1/2
2 3/4
1 5/8
1/4
PT 7186 EL - measurements in inches
2
2
1 5/8
1/4
6
PT 7186 EL - measurements in millimeters
7
PT 7186 EL - measurements in millimeters
8
Option: Installation on Miele base (UG/UO)
PT 7186 EL - measurements in millimeters
Option: Installation on Miele base (US)
9
Option: Installation on concrete platform (BS)
PT 7186 EL - measurements in millimeters
Standard installation
10
Technical datasheet
Tumble dryer:
Heating:
PT 7186
Electric (EL)
Legend:
en - US
Abbreviations in bold type:
Connection required
Abbreviations in circle with dashes:
Connection optional or required depending on model version
Optional extras:
UM
BS
Miele base
Concrete base
UO 6008 (UO = open base )
Height
Width
Depth
12''
26 15/16''
27 1/16''
305 mm
684 mm
687 mm
UG 6008 (UG = closed base)
Height
Width
Depth
12''
27 1/4''
27 1/16''
305 mm
692 mm
688 mm
US 6008 (US = base with drawer)
Height
Width
Depth
12 5/8''
27 1/4''
27''
320 mm
692 mm
685 mm
12''
2 3/4''
≥27 1/2''
≥27 1/2''
300 mm
70 mm
≥700 mm
≥700 mm
1. Standard voltage (2 AC 208V 60Hz)
Voltage
Frequency
Rated load
Fuse rating
Length of supply lead
Supplied with plug
V
Hz
kW
A
78 3/4''
NEMA L6-30P
2AC 208V
60
4.84
2 x 30
2000 mm
NEMA L6-30P
2. Standard voltage (2 AC 240V 60Hz)
Voltage
Frequency
Rated load
Fuse rating
Length of supply lead
Supplied with plug
V
Hz
kW
A
78 3/4''
NEMA L6-30P
2AC 240V
60
5.7
2 x 30
2000 mm
NEMA L6-30P
Quality and density of concrete must comply with load.
Concrete base must be firmly secured to floor!
Recommended height
Minimum height
Recommended width
Recommended depth
Machine connections:
Electrical
connection
Technical datasheet: PT 7186 EL (Electrically Heated)
Date: 2015-04-29
Page: 11
Electrical connection must comply with national regulations.
Connection using multi-pole lockable wall socket in
compliance with IEC/EN 60309 and IEC/EN 60947 is
recommended in order to simplify electrical tests. If machines
are hard-wired, a multi-pole mains switch must be provided
on site. Switches with a contact gap of more than 3 mm can
be used. These include switches, fuses and contactors
(IEC/EN 60947). A wall socket or mains isolator must be
easily accessible after installation.
Reinstallation of the supply point, changes to the equipment
or checks on the protective conductor, including determination
of correct fuse rating, should only be performed by a properly
trained electrician.
If necessary, equipotential bonding with good galvanic contact
must be provided in accordance with all appropriate national
and local regulations.
Vented
Nominal air throughput in vented mode
188 cfm
320 m³/h
Max. permissible pressure loss
Waste air/gas temperature, max.
Connector on machine (int. diameter)
Connection pipe provided on site (ext. diameter)
0.06 psi
176°F
3 15/16''
3 15/16''
420 Pa
80°C
100 mm
100 mm
37 in2
237 cm2
5/16'' x 2 9/16''
1/2'' x 2 3/8''
8 mm x 65 mm
12 mm x 60 mm
1/4'' x 2''
5/16'' x 1 9/16''
6 mm x 50 mm
8 mm x 40 mm
1/4'' x 2''
5/16'' x 1 9/16''
6 mm x 50 mm
8 mm x 40 mm
Miele adapter, Mat. no. 6595070 (int. diameter 100 mm) for
flexible aluminum ducting and adapter, Mat. no. 915051, (ext.
diameter 110 mm) for connection to standard heat-resistant
plastic pipes supplied.
As relative humidity inside the vent ducting can be as high as
100%, suitable measures must be taken to prevent a
backflow of condensate into the machine.
Air intake
Standard connection:
=> Air intake from installation site
Min. air intake cross-section
(to prevent draughts in room)
A sufficient supply of fresh air should be ensured to replace
the air extracted.
Fittings for base Miele base UG/UO 6008
/ floor
4 × metal angled brackets
installation
(to secure machine to base)
4 × screws DIN 571 (Ø × length)
4 × rawl plugs (Ø × length)
Base must be bolted to the floor. Machine must be fixed to the
base. Fixing materials for a floating screed floor are to be
provided on site.
Miele US 6008 base
4 x metal angled brackets
(to secure machine to base)
4 × screws DIN 571 (Ø × length)
4 × rawl plugs (Ø × length)
Base must be bolted to the floor. Machine must be fixed to the
base. Fixing materials for a floating screed floor are to be
provided on site.
Installation on floor or concrete base
2 × clamps
2 × screws DIN 571 (Ø × length)
2 × rawl plugs (Ø × length)
Machine must be fixed to the base or floor. Fittings are
supplied with machine. Fixing materials for a floating screed
floor are to be provided on site.
Technical datasheet: PT 7186 EL (Electrically Heated)
Date: 2015-04-29
Page: 12
Machine data
Unit width
Unit depth
Unit height
Casing width
Casing depth
27 9/16''
30 1/16''
40 3/16''
27 1/4''
27 3/16''
700 mm
763 mm
1020 mm
692 mm
690 mm
Minimum width of delivery access to installation site
Recommended rear wall gap (measured to front of machine)
Minimum rear wall gap (to front of machine)
Recommended rear wall gap ensures sufficient space for
maintenance and servicing.
28 3/8''
43 5/16''
35 7/16''
720 mm
1100 mm
900 mm
Net weight
170 lbs
77 kg
Dynamic floor load, max.
Average heat dissipation
(dependent on ambient room temperature and program
selected)
Sound pressure (re 20 mPA), workplace-related
(at distance of 1 m and height of 1.6 m)
1000 N
1535 BTU/hr
0.45 kWh
<70 dB (A)
Installation should only be carried out by authorized installers in accordance with valid regulations! Observe installation
instructions when installing machine! All rights reserved!
Technical datasheet: PT 7186 EL (Electrically Heated)
Date: 2015-04-29
Page: 13
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement